Zinwell ZWA-G192-OD User Manual

Wireless LAN Device Series

WLAN Outdoor Bridge

ZPlus-G192-OD User Manual

Version. 1.2.1 (25.03.2005)

Preface............................................................................................................................2

Chapter 1 - ZWA-G192 Installation...............................................................................4

Packing List ...........................................................................................................4

Hardware Installation.............................................................................................5

Chapter 2 - First Time Configuration ............................................................................8

Before Start to Configure.......................................................................................8

Knowing the Network Application........................................................................8

Basic Settings.......................................................................................................14

Advanced Settings ...............................................................................................34

Configuring Wireless Security.............................................................................37

Configuring as WLAN Client Adapter ................................................................ 40

Quick start to configure .......................................................................................40

Chapter 3 - Configuring WDS.....................................................................................43

WDS network topology .......................................................................................43

WDS Application.................................................................................................45

Chapter 4 - Advanced Configurations..........................................................................47

Configuring LAN to WAN Firewall....................................................................47

Port Filtering........................................................................................................47

IP Filtering...........................................................................................................47

MAC Filtering......................................................................................................48

Configuring Port Forwarding (Virtual Server) ....................................................48

Multiple Servers behind NAT Example:..............................................................49

Configuring DMZ................................................................................................49

Configuring WAN Interface.................................................................................50

Static IP................................................................................................................51

DHCP Client (Dynamic IP).................................................................................52

PPPoE ..................................................................................................................52

PPTP ....................................................................................................................53

Configuring Clone MAC Address.......................................................................54

Configuring DHCP Server...................................................................................57

Using CLI Menu..................................................................................................57

The System Management.....................................................................................59

About SNMP Agent .............................................................................................59

Firmware Upgrade...............................................................................................59

Configuration Data Backup & Restore................................................................60

Preface

This guide is for the networking professional who installs and manages the Ziwell

ZWA-G192 outdoor product, hereafter referred to as the “device”. To use this guide, you should have experience working with the TCP/IP configuration and be familiar with the concepts and terminology of wireless local area networks.

Chapter 1 - ZWA-G192 Inst allation

Packing List

Before you start to install the ODU, make sure the package contains the following items：

z Wireless Outdoor Bridge unit * 1 z Mounting Kit * 1 z Waterproof (IP67) RJ-45 Cable (30M) * 1 z Waterproof (IP66) RF Cable (1M) * 1 z Power Over Ethernet Kit * 1 z Ground Wire * 1 z 2.5” /4” U bolts * 2 and Anchor * 4 z 6 dBi omni directional antenna * 1 (separated package) z RJ-45 Cable (1.5M) * 1

ODU Mounting Kit

Waterproof RJ-45 Cable Waterproof RF Cable

Power Over Ethernet Kit Ground Wire

RJ-45 Cable 6 dBi omni directional antenna

2.5” /4” U bolt and Anchor

Hardware Installation

Once you check off everything from the package, you can start to install the ODU. You can mount to a pipe, a pole or to the side of a building. The steps are showed in the following：

1. You must mount the ODU into the bracket first.

Note:

ALL the 4 screws had been tightened onto the ODU and

bracket

2. Y ou can use the 2 or 4 inches U bolt to mount on the pipe, depending on the radius of the pipe. (Wall mounting is referred to Wall Mounting Figure) The two U bolts must be mounted tightly. Be aware of not over-tighten the U bolt.

Pipe Mounting Figure

Wall Mounting Figure

3. After checking the ODU is mounted well, you can connect the following two cables: the Waterproof RJ-45 network cable to “P+ DATA OUT” port of ODU and the RF cable to antenna port. Additional waterproof tool, such as waterproof tape, is recommended to use to enhance the waterproof function. It is suggested to have a lightening protector between antenna and antenna port. Connecting the ground wire as the figure of “ODU ground wire connection.”

ZPlus-G192-OD Cable Connection ZPlus-G192-OD Cable Connection

4. Plug the other end of the waterproof RJ-45 cable to the PoE device. The PoE device is guaranteed only in indoor environment.

DATA

P+DATA

OUT

Caution: DON’T plug the power cord into PoE device before you finish install

the antenna and Ground wire to ensure the safety.

If the RJ-45 cable’s length is not long enough to connect to your network device for indoor parts installation, you can extend the cable length. However, make sure the maximum length of the RJ-45 cable is shorter than 100M (about 109 yards) for normal operation under IEEE 802.3 standards.

When you plug the regular RJ-45 cable into the PoE device, you should use the regular RJ-45 cable to plug into the “DATA IN” of “Power Over Ethernet Kit” to connect to hub/switch or use the crosslink RJ-45 cable (Not included in the Packing List) to connect with user’s PC.

The waterproof RJ-45 cable must be connected to the “P+DATA OUT” port.

Caution: Be careful! Don’t plug the two cables inversely. It will damage the

devices!

We recommend you refer to the following illustration as a guideline for hardware installation.

Chapter 2 - First Time Configuration

Before Start to Configure

There are two interfaces to configure the device, one is web-browser interface, and the other is Secure Shell CLI interface. To access the configuration interfaces, make sure you are using a computer connected to the same network as the device. The default IP address of the device is

192.168.2.254, and the subnet-mask is 255.255.255.0.

The device has three operation modes (Router/Bridge/WISP). In bridge mode, you can access the device by both WLAN (Wireless Local Area Network) and wired LAN. And in router/WISP modes, the device can be accessed by both WLAN and WAN. The default IP addresses for the device are 192.168.2.254(for LAN), 172.1.1.1(for WAN), so you need to make sure the IP address of your PC is in the same subnet as the device, such as

192.168.2.X(for LAN), 172.1.1.X(for WAN).

Please note that the DHCP server inside the device is default to up and running. Do not have multiple DHCP servers in your subnet, otherwise it will cause abnormal situation.

Inside the CD, we provide the device auto-discovery tool, the tool can detect the device even your PC is not in the same subnet as the device in case the IP address of device is changed and forgot by user. The tool only can discover the device in your local area network.

Knowing the Network Application

ZWA-G192-OD can act as the following roles, and it supports WDS (Wireless Distribution System) function.

z Access Point z WDS (Wireless Repeater) z Bridge/Router z WISP z AP Client

The device provides 3 different operation modes and the wireless radio of device can act as AP/Client/WDS. The operation mode is about the communication mechanism between the wired Ethernet NIC and wireless NIC, the following is the types of operation mode.

Router The wired Ethernet (WAN) port is used to connect with ADSL/Cable modem and the wireless NIC is used for your private WLAN. The NAT is existed between the 2 NIC and all the wireless clients share the same public IP address through the WAN port to ISP. The default IP configuration for WAN port is static IP. You can access the web server of device through the default WAN IP address 172.1.1.1 and modify the setting base on your ISP requirement.

Bridge The wired Ethernet and wireless NIC are bridged together. Once the mode is selected, all the WAN related functions will be disabled.

WISP (Wireless ISP) This mode can let you access the AP of your wireless ISP and share the same public IP address form your ISP to the PCs connecting with the wired Ethernet port of the device. To use this mode, first you must set the wireless radio to be client mode and connect to the AP of your ISP then you can configure the WAN IP configuration to met your ISP requirement.

The wireless radio of the device acts as the following roles.

AP (Access Point) The wireless radio of device serves as communications “hub” for wireless clients and provides a connection to a wired LAN.

AP Client This mode provides the capability to connect with the other AP using infrastructure/Ad-hoc networking types. With bridge operation mode, you can directly connect the wired Ethernet port to your PC and the device becomes a wireless adapter. And with WISP operation mode, you can connect the wired Ethernet port to a hub/switch and all the PCs connecting with hub/switch can share the same public IP address from your ISP.

WDS (Wireless Distribution System) This mode serves as a wireless repeater, the device forwards the packets to another AP with WDS function. When this mode is selected, all the wireless clients can’t survey and connect to the device. The device only allows the WDS connection.

WDS+AP This mode combines WDS plus AP modes, it not only allows WDS connections but also the wireless clients can survey and connect to the device.

The following table shows the supporting combination of operation and wireless radio modes.

WDS

Client

AP+WDS

Bridge Router WISP

v v x v v x v x v v v x

Hereafter are some topologies of network application for your reference.

WDS+AP - Router

Internet

ADSL

WDS+AP - Bridge

AP - Bridge

Infrastructure Client – Router (WISP)

Infrastructure Client - Bridge

+ 21 hidden pages

Zinwell ZWA-G192-OD User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual