ZiLOG Z8F08200100KIT User Manual

Z8F08200100KIT

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

User Manual

UM015006-1207

Copyright ©2007 by Zilog®, Inc. All rights reserved.

www.zilog.com

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

Revision History

Each instance in Revision History reflects a change to this document from
its previous revision. For more details, refer to the corresponding pages
and appropriate links in the table below.

Revision

Date

Level Description Page No

User Manual

ii

December
2007

November
2006

November
2005

06 Updated document with new Zilog

logo and disclaimer. Implemented
Style Guide. Replaced Z8 Encore!
8K/4K Series with Z8 Encore! XP
F0822 Series Flash Microcontrollers.

05 Changed Figure 14 to Figure 2. 5

04 Removed the word Preliminary from

all page footers and updated
trademarks.

®

®

All

All

UM015006-1207 Revision History

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Software (on CD-ROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System/Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Supported Host System Configuration . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Z8 Encore! XP

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

UART with IrDA Endec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Power and Communication Interfaces . . . . . . . . . . . . . . . . . . . . . 8

External Interface Headers JP1 and JP2 . . . . . . . . . . . . . . . . . . . 9

Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Customer Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

®

F0822 Series Flash MCU Evaluation Board . . . . 5

User Manual

iii

UM015006-1207 Table of Contents

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

Introduction

User Manual

1

Zilog’s Z8 Encore! XP® F0822 Series Flash MCU is a part of Zilog®
microcontroller products. The Z8 Encore! XP
(Z8F08200100KIT) allows you to get familiar with the hardware and
software tools available with this product. This kit consists of the 8 KB
version of the Z8 Encore! XP evaluation board that supports and presents
the features of the Z8 Encore! XP F0822 Series Flash MCU. This kit
allows you to write application software and contains all supporting
documents.

This user manual acquaints you with the Z8 Encore! XP F0822 Series
Flash MCU development kit and provides instructions on setting up and
using the tools to start building designs and applications.

Safeguards

The following precaution must be observed when working with the
devices described in this document.

Caution:

electrostatic discharge (ESD).

Kit Contents

Z8 Encore! XP F0822 Series Flash MCU development kit (see Figure 1
on page 2) contains the following:

®

MCU development kit

Always use a grounding strap to prevent damage resulting from

Hardware

The hardware included are:

•

Z8 Encore! XP F0822 Series Flash MCU evaluation board

•

Smart Cable for PC to Z8 Encore! XP F0822 Series Flash MCU
evaluation board (DB9 to six-pin male)

UM015006-1207 Introduction

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

•

5 V DC power supply

CD-ROM Containing

Documentation

Smart Cable

User Manual

2

Packaging

Power

Supply

Evaluation
Board

Figure 1. Z8 Encore! XP® MCU Development Kit Contents

Software (on CD-ROM)

The software (on CD-ROM) includes:

•

Zilog Developer Studio (ZDS II)- Z8 Encore! IDE with ANSI C­Compiler

•

Sample code

•

Document browser

•

Acrobat Reader

UM015006-1207 Introduction

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

Documentation

The documentation includes:

•

Quick Start Guide

•

Z8 Encore! XP F0822 Series Flash MCU technical documentation (on
CD-ROM):

– Development kit User Manual

– ZDS II - IDE User Manual

– eZ8 CPU User Manual

– Product Specification

– Product brief

– Application notes

– Programmer’s Reference Sheet

User Manual

3

The sample code is installed with ZDS II and resides in the disk drive at:

<installation directory>\samples

The documentation can be installed with the DemoShield interface or
can be viewed on the CD-ROM using the DemoShield menus and a PDF
reader. A copy of the Acrobat installer is provided on the CD-ROM and
can be installed from the DemoShield install screen. After installing the
documentation, Windows Explorer can be used to select any document
to be viewed with PDF file viewer.

System/Software Requirements

An IBM PC (or compatible computer) with the following minimum
configurations:

Supported Host System Configuration

The host system configuration for Z8 Encore! XP F0822 Series Flash
MCU development kit includes:

•

Win98 Second Edition/ WinNT 4.0 Service Pack 6/ Win2000 Service
Pack 3/ WinXP Service Pack 1

UM015006-1207 Introduction

Installation

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

User Manual

•

Pentium II/233 MHz processor or higher up to Pentium IV, 2.8 GHz

•

96 MB RAM or more

•

25 MB hard disk space or more

•

Super VGA video adapter

•

CD-ROM

•

One or more RS-232 communication ports

Follow the directions in the Quick Start Guide for software installation
and setup of the Z8 Encore! XP development kit.

4

UM015006-1207 Introduction

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

®

Z8 Encore! XP

F0822 Series Flash

MCU Evaluation Board

Z8 Encore! XP® F0822 Series Flash MCU evaluation board (see

Figure 2) is an evaluation and prototyping board for the Z8 Encore! XP

F0822 Series Flash MCU. The board provides you with a tool to evaluate
features of Z8 Encore! XP F0822 Series Flash MCU, and to start
developing an application before building the hardware.

User Manual

5

RESET

P2

RS-232

Serial Port

TEST

U6

J1

Figure 2. Z8 Encore! XP F0822 Series Flash MCU Evaluation Board

Y1

J2

LEDs

UM015006-1207 Z8 Encore! XP® F0822 Series Flash MCU

Features

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

User Manual

The features of Z8 Encore! XP F0822 Series Flash MCU evaluation board
include:

•

Z8 Encore! XP MCU (28-pin SOIC)

•

3 LEDs

•

RS-232 interface

•

IrDA transceiver

•

Two pushbuttons–RESET and TEST

•

5 V DC power connector

•

On-Chip Debugger (OCD) interface

•

Crystal Oscillator at 18.432 MHz

6

•

Header for ADC input

•

Prototyping area

•

External interface connectors JP1 and JP2

•

2.7 V to 3.6 V operating voltage with 5 V-tolerant inputs

MCU

Z8 Encore! XP F0822 Series Flash MCU is member of Zilog family of
microcontroller products based upon the 8-bit eZ8 core CPU. The Flash
in-circuit programming capability allows for faster development time and
program changes in the field. The eZ8 core CPU is upward compatible
with existing Z8
Z8 Encore! XP F0822 Series Flash MCU makes it suitable for various
applications including motor control, security systems, home appliances,
personal electronic devices, and sensors.

The evaluation board contains circuitry to support and present all the
features of the Z8 Encore! XP F0822 Series Flash MCUs.

UM015006-1207 Z8 Encore! XP® F0822 Series Flash MCU

®

instructions. The rich peripheral set of

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

User Manual

The main features of Z8 Encore! XP F0822 Series Flash MCUs include:

•

eZ8 core CPU

•

8 KB Flash memory with in-circuit programming capability

•

1 KB register RAM

•

5-channel, 10-bit Analog-to-Digital Converter (ADC)

•

Full-duplex UART

•

I2C interface (Master Mode only)

•

Serial Peripheral Interface (SPI)

•

Infrared Data Association (IrDA)-compliant infrared encoder/decoder
(Endec)

•

Two 16-bit timers with capture, compare, and PWM capability

7

•

Watchdog Timer (WDT) with internal RC oscillator

•

Eleven or nineteen I/O pins

•

Programmable priority interrupts

•

On-Chip Debugger

•

Voltage Brownout Protection (VBO)

•

Power-On Reset (POR)

•

2.7 V to 3.6 V operating voltage with 5 V-tolerant inputs

•

Operating temperatures: 20 °C ±10 °C

For further information on the Z8 Encore! XP family of devices, refer to
Z8 Encore! 8K and 4K Series Product Specification (PS0243) available
for download at www.zilog.com

UM015006-1207 Z8 Encore! XP® F0822 Series Flash MCU

.

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

UART with IrDA Endec

The Z8 Encore! XP F0822 Series Flash MCU contains a fully-functional,
high-performance UART with Infrared Encoder/Decoder, component U6.
The Infrared ENDEC is integrated with an on-chip UART allowing easy
communication between the Z8 Encore! XP F0822 Series Flash MCU and
IrDA transceivers. Infrared communication provides secure, reliable, low­cost, point-to-point communication between PCs, PDAs, cell phones,
printers, and other infrared enabled devices.

Crystal Oscillator

The evaluation board is shipped with an 18.432 MHz Crystal Oscillator
(Y1). To change the crystal oscillator you must change the clock
frequency of ZDS II. The frequency settings is found at

→ Debugger → ZDB: Configure ZDB Driver: Clock Frequency. For

tings

supported frequencies, refer to Z8 Encore! XP

User Manual

Project → Set-

®

Product Specification .

8

Power and Communication Interfaces

Table 1 provides jumper information concerning the shunt status,

functions, devices and defaults affected by jumpers JP3 and JP4.

UM015006-1207 Z8 Encore! XP® F0822 Series Flash MCU

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

User Manual

Table 1. Jumpers JP3 and JP4

Device

Jumper Status

JP3**OUT*RS-232

JP3 IN RS-232

JP4 OUT* IrDA

JP4 IN IrDA

* These jumpers must not be OUT at the same time.

** If the module is plugged onto an eZ80

demonstration board the local RS-232 can be disabled by connecting header
JP2 pin 50 to the corresponding GND on the mating connector

Affected Status Default

Enabled X

interface

Disabled

interface

Enabled

interface

Disabled X

interface

®

Evaluation platform or eZ80

.

9

External Interface Headers JP1 and JP2

The external interface headers, JP1 and JP2 contain no connectors when
the board is shipped. You can insert 0.1" space connectors of choice.

UM015006-1207 Z8 Encore! XP® F0822 Series Flash MCU

Schematics

Figure 3 and Figure 4 displays the schematics for Z8 Encore! XP® F0822 Series Flash MCU Evaluation Board.

5 4 3 2 1

GND

PA6_SCL
PA7_SDA

-RESET
GND
XIN
XOU
VCC_33V

PA0_T0IN
PA1_T0O

PA2

C15
18pF

VCC_33V

GND

PA0_T0IN

PA1_T0O

PA2

T

UT

Y1

18.432MHz

R14

100K

D2

RED
D3

UT

GREEN

D4

YELL

20 pin Socket 28 pin Socket

U7

1

PA6/SCL

2

PA7/SDA

3

RESET

4

GND

5

XIN

6

XOUT

7

VDD

8

PA0/T0IN

9

PA1/T0OUT
PA2/DE

Z8F0xx1

XIN

XOU

T

R13
220

18pF

C16

VCC_33V

D D

C C

B B

A A

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

User Manual

10

VCC_33V

+

C13

C12

0.01uF

22uF

GND

R8

21

21

21

100

R9

100

R11

100

20

PC0/T1IN
PB0/ANA0
PB1/ANA1

PA5/TXD0
PA4/RXD0
PA3/CTS0

RESET

PB0_ANA0

19
18
17

VREF

16

AGND

VCC_33V

15

AVDD

14

DBG

PA

13

PA4_RXD0

12

PA3_CTS0

1110

VCC_33V

-RESET

SW1

PB0_ANA0 PB2_ANA2

PC0_T1IN

VREF
AGND

DBG

5_TXD0

R3
10K

C10

0.01uF

VCC_33V

-RESET

PB1_ANA1

C17

0.001uF

R10

100K

R12
100

C18

0.001uF

SW2

TEST

PC0_T1IN
PA6_SCL
PA7_SDA

-RESET

PC5_MISO
PC4_MOSI
PC3_SCK
PC2_SS
PA0_T0IN
PA1_T0O

1
2
3
4

GND

5

XIN

6

XOU

T

7

VCC_33V

8

9
10
11
12
13

UT

14 15

PB3_ANA3

C19

0.001uF

GND

U8

PC0/T1IN
PA6/SCL
PA7/SDA
RESET
VSS
XIN
XOUT
VDD
PC5/MISO
PC4/MOSI
PC3/SCK
PC2/SS
PA0/T0IN
PA1/T0OUT

Z8F0XX2

PB4_ANA4

C20

0.001uF

C4

0.1uF

C21

0.001uF

PB0/ANA0
PB1/ANA1
PB2/ANA2
PB3/ANA3
PB4/ANA4

VREF
AVSS
AVDD

DBG

PC1/T1OUT

PA5/TXD0
PA4/RXD0
PA3/CTS0

PA2/DE

AGND

28
27
26
25
24
23
22
21
20
19
18
17
16

VREF

PB0_ANA0
PB1_ANA1
PB2_ANA2PB1_ANA1
PB3_ANA3
PB4_ANA4

VREF
AGND
VCC_33V

DBG
PC1_T1OUT
PA

5_TXD0
PA4_RXD0
PA3_CTS0

PA2

+

C14
22uF

DBG

C22

0.01uF

VCC_33V
PC4_MOSI

PC3_SCK
PC0_T1IN

GND

PC1_T1OUT

PA3_CTS0
PA4_RXD0

GND

PA6_SCL
PA7_SDA

-RESET
VCC_33V

VCC_33V

PB0_ANA0
PB1_ANA1
PB2_ANA2
PB3_ANA3
PB4_ANA4

connector

JP2

1
3
5
7

9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59

HEADER 30x2/SM

DBG

DBG

PA

5_TXD0

PA5

PA3_CTS0

PA3_CTS0

PA4_RXD0

PA4_RXD0

2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60

_TXD0

J2
12

34
56
78
9

10

Header 5x2

2

GND
PC5_MISO

PA1_T0O

PA

-DIS_IrDA

PC2_SS
PA0_T0IN

PA2

GND

5_TXD0

GND

GND

UT

If Module is plugged onto the Dev Platform the local

RS232 interface is disabled by pin 50 of JP2

-DIS_232

-DIS_IRDA

connector
for
referenc
only

1
3

-TRSTN

5

-F91_WE

7

GND

9

A6

11

A10

13

GND

15

A8

17

A13

19

A15

21
23

A19

25
27

A11

29

A4

31

A5

33
35

A21

37

A22

39

-CS0

41

-CS2

43

D1

45

D3

47

D5

49

D7

51

-MREQ

53

GND

55

-WR

57

-BUSACK

59

JP1

2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60

HEADER 30x2/SM

1

e

VCC_33V
A0
A3

VCC_33V

A7

A9
A14
A16A18

GND
A1A2
A12
A20

A17

-DIS_FLASH
VCC_33V

A23

-CS1
D0
D2
D4

GND

D6

-IOREQ

-RD

-INSTRD

-BUSREQ

VCC_33V

Figure 3. Schematic for Z8 Encore! XP F0822 Series Flash MCU Evaluation Board

UM015006-1207 Schematics

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

96C0897-001

B

User Manual

11

J1

PWR JACK

D D

GND

C C

B B

A A

5 4 3 2 1

2
3
1

F1

RXE

110

U2

3 2

VIN

VOUT

1

GND

LT1086-3.3/TO220

TP1

0.1uF

12345

GND

5V

C9

GND

C23

0.1uF

+

100/10

C8

TP2

+

C1

100/10

VCC_33V

R1
680

21

D1

12345

VCC

LED

VCC_33V

VCC

VCC_33V

3.3 O

-DIS_232

JP3

1
2

DIS RS232

K

VCC_33V

R15
10K

PA5

_TXD0

PA3_CTS0
PA4_RXD0

1 2

GND

PA

147

5_TXD0

U4A

C3

0.1uF

C5

0.1uF

PA3_CTS0

PA4_RXD0

74LVC04/SO

GND

VCC_33V

2
4
5
6

13
12

15
10

1

20

GND

U10
C1+
C1­C2+
C2-

T1IN
T2IN

R1OUT
R2OUT

EN
SHDN
MAX3

VCC_33V

1918

VCCGND

222

-DIS_IRDA

JP4

1
2

DIS IRDA

DBG
INTERFACE

P2
12

34
56

Header 3x2

T1OUT
T2OUT

R1IN
R2IN

GND

3

V+

GND

C7

R4
10K

VCC_33V

R7
10K

-RESET
DBG

0.1uF

3 4

GND

-RESET
DBG

147

U4B

74LVC04/SO

7

V-

17
8

16
9

14

NC

11

NC

C6

0.1uF

R5

68

R6
2R7

PA

5_TXD0

IRDA_SD

PA4_RXD0

Title

Encore! F08. Evaluation Module. Schemati

SizeDocument Number

B

TXD

5
1
2
4
3
6

CTS0
RXD0

0

C11

330nF

VCC
LEDA
TXD
SD
RXD
GND

U6

CONSO

1
6
2
7
3
8
4
9
5

DB9 Female

T

ZHX1810

0

USER

LE

P1

c.

Rev

Figure 4. Schematic for Z8 Encore! XP F0822 Series Flash MCU Evaluation Board

UM015006-1207 Schematics

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

Customer Support

For answers to technical questions about the product, documentation, or
any other issues with Zilog’s offerings, please visit Zilog’s Knowledge
Base at http://www.zilog.com/kb.

For any comments, detail technical questions, or reporting problems,
please visit Zilog’s Technical Support at http://support.zilog.com.

User Manual

12

UM015006-1207 Customer Support

Z8 Encore! XP® F0822 Series Flash MCU Development Kit

User Manual

Warning:

DO NOT USE IN LIFE SUPPORT

LIFE SUPPORT POLICY

ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF ZILOG CORPORATION.

As used herein

Life support devices or systems are devices which (a) are intended for surgical implant
into the body, or (b) support or sustain life and whose failure to perform when properly
used in accordance with instructions for use provided in the labeling can be reasonably
expected to result in a significant injury to the user. A critical component is any
component in a life support device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.

Document Disclaimer

©2007 by Zilog, Inc. All rights reserved. Information in this publication concerning the
devices, applications, or technology described is intended to suggest possible uses and
may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR
PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE.The
information contained within this document has been verified according to the general
principles of electrical and mechanical engineering.
Z8, eZ80, Z8 Encore!, and Z8 Encore! XP are trademarks or registered trademarks of
Zilog, Inc. All other product or service names are the property of their respective owners.

UM015006-1207