Z8400/84C00
Z
ILOG
Z8400/84C00
NMOS/CMOS Z80 CPU
CENTRAL PROCESSING UNIT
GENERAL DESCRIPTION
The Z8400/Z84C00 CPUs are fourth-generation enhanced
microprocessors with exceptional computational power.
They offer higher system throughput and more efficient
memory utilization than comparable second- and thirdgeneration microprocessors. The speed offerings from 6 20 MHz suit a wide range of applications which migrate
software. The internal registers contain 208 bits of read/
write memory that are accessible to the programmer.
These registers include two sets of six general purpose
registers which may be used individually as either 8-bit
registers or as 16-bit register pairs. In addition, there are
two sets of accumulator and flag registers. A group of
“Exchange” instructions makes either set of main or alternate registers accessible to the programmer. The alternate set allows operation in foreground-background mode
or it may be reserved for very fast interrupt response.
The CPU also contains a Stack Pointer, Program Counter,
two index registers, a Refresh register (counter), and an
Interrupt register. The CPU is easy to incorporate into a
system since it requires only a single +5V power source. All
output signals are fully decoded and timed to control
standard memory or peripheral circuits; the CPU is supported by an extensive family of peripheral controllers.
FEATURES
■ The Extensive Instruction Set.Contains 158 Instructions,
Including the 8080A Instructions Set as a Subset.
■ Single 5 Volt Power Supply
■ NMOS Version for Low Cost, High Performance
Solutions; CMOS Version for High Performance, Low
Power Designs.
■ NMOS Z084004 - 4 MHz
Z0840006 - 6.17 MHz
Z084008 - 8 MHz
■ CMOS Z0840006 - DC to 6.17 MHz
Z84C0008 - DC to 8 MHz
Z84C0010 - DC to 10 MHz
Z84C0020 - DC to 20 MHz
■ 6 MHz Version can be Operated at 6.144 MHz Clock
Speed
■ The Z80 Microprocessors and Associated Family of
Peripherals can be Linked by a Vectored Interrupt
System. This System can be Daisy-Chained to Allow
Implementation of a Priority Interrupt Scheme.
■ Duplicate Set of Both General-Purpose and Flag
Registers
■ Two 16-Bit Index Registers
■ Three Modes of Maskable Interrupts:
- Mode 0 - 8080A Similar
- Mode 1 - Non-Z80 Environment, Location 38H
- Mode 2 - Z80 Family Peripherals, Vectored Interrupts
■ On-Chip Dynamic Memory Refresh Counter
PB006301-0301
Z8400/84C00
Z
ILOG
GENERAL DESCRIPTION (Continued)
PB006301-0301
8-Bit
Data Bus
Data Bus
Interface
+5V
GND
Clock
Instruction
Decoder
CPU
Timing
Control
8 Systems
and CPU
Control
Outputs
Figure 1. Z8400/C00 Functional Block Diagram
5 CPU
Control
Inputs
Instruction
Register
CPU
Timing
Internal Data Bus
Register
Array
Address
Logic and
Buffers
16-Bit
Address Bus
ALU
© 1997 by Zilog, Inc. All rights reserved. No part of this document
may be copied or reproduced in any form or by any means
without the prior written consent of Zilog, Inc. The information in
this document is subject to change without notice. Devices sold
by Zilog, Inc. are covered by warranty and patent indemnification
provisions appearing in Zilog, Inc. Terms and Conditions of Sale
only.
ZILOG, INC. MAKES NO WARRANTY, EXPRESS, STATUTORY,
IMPLIED OR BY DESCRIPTION, REGARDING THE INFORMATION SET FORTH HEREIN OR REGARDING THE FREEDOM OF
THE DESCRIBED DEVICES FROM INTELLECTUAL PROPERTY
INFRINGEMENT. ZILOG, INC. MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
Zilog, Inc. shall not be responsible for any errors that may appear
in this document. Zilog, Inc. makes no commitment to update or
keep current the information contained in this document.
Zilog’s products are not authorized for use as critical components in life support devices or systems unless a specific written
agreement pertaining to such intended use is executed between
the customer and Zilog prior to use. Life support devices or
systems are those which are intended for surgical implantation
into the body, or which sustains life whose failure to perform,
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result in
significant injury to the user.
Zilog, Inc. 210 East Hacienda Ave.
Campbell, CA 95008-6600
Telephone (408) 370-8000
Telex 910-338-7621
FAX 408 370-8056
Internet: http://www.zilog.com
Loading...