Page 1
Mist Kit for EBZ8000 / EBZ8001
848L8293A1 (708)
OWNER’S MANUAL
MIST KIT FOR BLOWERS
G
G
B
B
MIST KIT FOR
EBZ8000
EBZ8001
GB-1
Page 2
Mist Kit for EBZ8000 / EBZ8001
SAFETY FIRST
Instructions contained in warnings within this manual marked
with a
into consideration to prevent possible serious bodily injury, and
for this reason you are requested to read all such instructions
carefully and follow them without fail.
WARNINGS IN THE MANUAL
This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
This mark indicates instructions, which must be followed, or it
leads to mechanical failure, breakdown, or damage.
This mark indicates hints or directions useful in the use of the
product.
symbol concern critical points which must be taken
WARNING
IMPORTANT
NOTE
WARNING
Never attach this mist kit to other than applicable models. Failure to do so may void your
warranty.
APPLICABLE MODEL : EBZ8000, EBZ8001
Contents
1. Specifications ................................................. 2
2. Warning labels on the machine ...................... 2
3. For safe operation ........................................... 3
4. Set up ............................................................. 6
5. Operation ........................................................ 7
6. Maintenance ................................................... 7
7. Storage ........................................................... 8
8. Disposal .......................................................... 8
1. Specification
This data is when the “Mist Kit” is mounted on EBZ8000, EBZ8001.
Model Mist Kit for EBZ8000, EBZ8001
Purpose Spraying agricultural chemicals and cold water
for pest control, weeding, and growth control
Capacity of chemical fluid tank liters 14
Pump Longitudinal coverage Horizontal m 22
Vertical m 14
Maximum water absorption liters / min. 5.5
Specifications are subject to change without notice.
2. Warning labels on the machine
If warning label peels off or becomes soiled and
Read owner’s manual before operating this machine.
Wear head, eye and ear protection.
Warning / Attention
Keep all children, bystanders and helpers 15
meters away from the machine.
GB-2
impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the required
location(s).
Never modify your machine.
We won’t warrant the machine, if you use the
remodeled blower or if you don’t observe
proper usage written in the manual.
the
Page 3
3. For safe operation
Mist Kit for EBZ8000 / EBZ8001
Before using this product, please read this Operator's
Manual thoroughly to ensure correct operation. The following are precautions that should be observed in order
to use the product smoothly. Elsewhere in the Manual,
the
warning mark is used to bring your attention to
these precautions.
BEFORE USING THE PRODUCT
• This product has been designed mainly for the purpo se of sp rayi ng pest con tro l ch emic als and
weedkillers. Please do not use it for any other purpose, as this may cause unforeseen accidents.
• Since this product uses agricultural chemicals that
require careful operation, misuse can be dangerous.
Do not use this product when tired or otherwise in
poor physical condition, or when you may be unable
to judge correctly or operate accurately, such as after taking cold relief medicines or drinking alcohol.
Also, children or persons who are unable to understand the contents of this Manual should under no
circumstances be permitted to use the product.
• The engine exhaust gas contains toxic carbon monoxide. Please do not use the product indoors, in vinyl
houses or tunnels, or in other poorly ventilated places.
• Do not use this product in the following cases.
1. When the product could fall over or in other situations when it is difficult to hold or operate.
2. After sunset or at other times when eyesight is poor
and the safety of the spraying area is difficult to ascertain.
3. In worsening weather (rain, fog, strong wind, lightning, etc.)
• When using for the first time, before commencing
actual spraying please receive guidance in operating the product from a person with adequate experience.
• Fatigue reduces powers of concentration and increases the risk
of accidents. When planning work, please allow
ample time,
setting a limit of 30-40 minutes for single spraying
sessions and breaks of 10-20 minutes in between.
Also, do not spray for more than 2 hours in any one
day.
• Please take good care of this Operator's Manual and
refer to it for additional information from time to time.
• When selling or lending this product, it should be accompanied by this Operator's Manual.
PRECAUTIONS BEFORE SPRAYING
• Make sure you have the correct protective clothing,
headgear, rubber gloves and boots, a protective
mask, goggles, a towel, protective cream, etc., to
prevent chemicals from coming into contact with your
skin or entering your lungs. When spraying, please
wear this protective gear to prevent any risk of injury.
1. Protective headgear
2. Protective goggles
3. Protective mask
4. Rubber boots
5. Ear muffs
6. Neck covering
7. Protective clothing
8. Rubber gloves
9. Protective clothing
• Please store chemicals in a locked storage box,
locker, or other safe place out of the reach of children.
• Carefully read the instructions for using the chemicals, and familiarize yourself with the level of toxicity,
method of use, etc.
• Please pay all due consideration to the area in which
you will be spraying, to ensure that you do not pollute the water supply, rivers, lakes, ponds, etc., or
cause any damage to residents, passers-by, livestock, etc.
• Prepare yourself physically on the day before spraying, by for example cutting down on alcoholic beverages or late-night work.
• Do not allow children, animals, etc., to enter the
chemical spraying area.
• Before spraying, please prepare fully by inspecting
sprayer nozzles and checking for abnormalities such
as loose screws or spray hose connections, fuel
leaks, defective or broken fluid gaskets, or damage
to the carrying band.
PR E CA U T IO N S WH E N TR A N SP O R TI N G
CHEMCALS
• When transporting chemicals, please handle with
care to ensure that there is no spillage of chemicals
from torn bags, broken bottles, or loose stoppers.
• Do not carry chemicals in the same container as food.
PRECAUTIONS WHEN TRANSPORTING THE
SPRAYER
• Do not transport the sprayer while it has chemicals
or fuel in the tank, as these could leak out as a result
GB-3
G
B
Page 4
Mist Kit for EBZ8000 / EBZ8001
3. For safe operation
of impact during transportation.
• When transporting in a vehicle, please use a rope or
similar to fix the sprayer firmly to the cargo trailer in
an upright position. Please do not transport by bicycle or motorbike, as this is dangerous.
PRECAUTIONS CONCERNING FUEL
• The engine of this product is fueled by "mixed gasoline" that includes highly combustible fuel. Do not
refuel or store fuel containers where there is any risk
of combustion from incinerators, burners, bonfires,
kitchen stoves, electric sparks, welding sparks, etc.
• Smoking while spraying or refueling is dangerous.
Please avoid this at all costs.
• When refueling during use, always stop the engine
and make sure there are no naked flames in the vicinity before refilling.
• Any fuel spilt during refueling should be wiped off
completely with a rag or similar before starting the
engine.
• After refueling, seal the fuel container, tightly close
the fuel tank cap, and start the engine at least 3
meters away.
peratures are relatively cool and winds are low.
• When starting work, please pay all due consideration
to the spraying time, wind direction, etc., to ensure
that no noise disturbance or chemical hazard is
caused to nearby residents, passers-by, farm crops,
and so on.
• While spraying please hold the grip firmly at all times
and be careful not to point the nozzle in the direction
of people or animals.
• While spraying please be careful of the wind direction and always stand on the upwind side, to avoid
spraying yourself with chemicals.
• Should you begin to feel even
slightly unwell while spraying, consult a doctor immediately. When doing so, inform the doctor of the
name of the chemical you were using, the conditions
of use, etc.
• If the sprayer is tilted the chemical may leak out
through the air holes in the cap. When spraying always make sure you have a firm footing and maintain your balance.
• Do not touch the spark plugs or plug cords while the
engine is running, as you may get an electric shock.
PRECAUTIONS WHEN REFILLING CHEMCALS
• Before filling the tank with chemicals, please make
sure that the intermediate valve is closed.
• After chemical refilling, firmly tighten the tank cap. If
not fully tightened the cap may become loose during spraying, with the risk of physical exposure to
the chemicals.
(2)
(1)
(1)OPEN
(2)CLOSE
• Do not fill chemicals over 14 liters.
• Do not mix different chemicals.
• Wash the chemical fluid tank and the nozzle cleanly
when you change the type of chemical.
PRECAUTION WHEN STARTING THE ENGINE
• Please keep children, animals, etc. well away when
starting the engine and spraying.
PRECAUTIONS WHEN SPRAYING
• Since protective clothing generally offers poor ventilation and thus places stress on the body, there is a
risk of contracting heatstroke or other illness when
operating for long periods under high temperatures.
Please avoid spraying on hot days, aiming instead
for early morning and late afternoon times when tem-
GB-4
• Do not touch the muffler, spark plugs, or other metal
parts with your bare hands while the engine is running or immediately after stopping the engine, as
there is the risk of burns due to high temperatures.
PRECAUTIONS AFTER SPRAYING
• Please seal unused chemicals and store them out of
the reach of children.
• Do not simply discard empty chemical containers,
but dispose of them safely by incinerating, burying,
or another similar method. In addition, please take
every care that the water used to clean spraying tools
does not create any hazard.
• Fully inspect and maintain protective clothing, masks,
gloves, and other protective gear in preparation for
the next session.
• After completing the work and tidying away chemicals and spraying tools, you should immediately take
a bath or wash your hands, feet, face, etc. thoroughly
with soap, as well as washing your mouth out.
• You should change all clothes worn, including underwear, and wash them thoroughly. Clothes worn
during spraying should not be worn again the following day.
• After spraying, please limit your alcohol intake and
Page 5
3. For safe operation
rest thoroughly by going to bed early. If you feel even
slightly unwell, please see a doctor as soon as
possible.
Mist Kit for EBZ8000 / EBZ8001
OTHER PRECAUTIONS
• When engaged in spraying work over a protracted
period of time, please have your health checked regularly.
• Please carry out spraying in a planned fashion, keeping a daily record of the date and time of spraying,
the chemicals used, the target pest, contents of the
work, duration of the work, and other details.
• Please keep the following points in mind when selecting or using protective gear.
a) Protective clothing
Choose clothing that is cool to wear and offers good
ventilation and waterproofing. In addition, wear items
that enable you to carry out spraying work in total
comfort and safety.
b) Spraying hood
Use a hood with a brim that is waterproof and covers
your neck and shoulders.
c) Gloves
Use gloves that are difficult for chemicals to penetrate
and do not slip even if you perspire while doing the
work.
d) Rubber apron
When mixing chemicals, wear a long, thick, and wide
apron that cann ot be penetra ted by chem ical
splashes.
e) Protective goggles, mask, etc.
Select suitable protective goggles, mask, rubber
boots, eye washer, and protective cream, etc., paying attention to standards and the recommendations
of farm work safety promotion organizations.
G
B
• For replacement parts, please use original ZENOAH
parts or brands designated by ZENOAH.
MAINTENANCE OF LABELS
1. Please keep warning labels clean and unmarked.
2. If warning labels become soiled or peel off, please
order from your supplier and replace with new ones.
3. When affixing new labels please wipe off all dirt and
moisture.
MAINTENANCE PRECAUTIONS
• In order to maintain the functions of the product, regularly carry out the maintenance inspections listed in
this Manual. When maintenance or parts replacement
not indicated in this Manual are required, please consult your product supplier or nearest ZENOAH product dealer.
• Never keep the engine running while carrying out
inspections or maintenance.
• Do not modify the sprayer or dismantle the engine.
This could lead to breakdown and serious accidents
during operation.
• Do not touch the muffler or spark plugs with your bare
hands immediately after stopping the engine. There
is the risk of burns due to high temperature.
GB-5
Page 6
Mist Kit for EBZ8000 / EBZ8001
4. Set up
COMPONENTS (pcs.)
(A) Tank Ass’y ............. 1
(B) Valve Ass’y............ 1
(C) Mist Nozzle Ass’y .. 1
(D) Frame .................... 1
(E) Plate ...................... 1
(F) Plate ...................... 2
(G) Plate ...................... 2
(H) Spacer .................. 1
(I) Pipe ....................... 1
(J) Screw 5 x 14 ......... 4
(K) Screw 5 x 20 ......... 2
(L) Screw 5 x 25 ......... 6
(M) Tube ...................... 1
(N) Clip ....................... 4
(O) Clamp ................... 1
(D)
(A)
(F)
(M)
(B)
(E)
(G)
(K)
(J)
(C)
(N)
(H)
(O)
(L)
(I )
ASSEMBLY
1. Remove the back pad from the back plate.
(2)
(1) Back plate
(1)
2. Fit frame (D) in the groove of the back plate, and fasten it with 2 plates (G) and 6 screws (L).
3. Fasten the spacer (H) with 2 screws (K) .
4. Replace the back pad.
(D)
(L)
(G)
(2) Back pad
(L)
(G)
(H)
5. Set the tank (A) as shown in the picture, and fasten it
with the plate (E), 2 plates (F) and 4 screws (J) .
6. Connect the tube (M) to the volute and tank (A) , and
fasten it with 2 clips (N) .
(A)
(N)
(M)
(N)
(J)
(F)
(E)
(J)
(F)
(1)
(1) Volute
7. Connect the mist nozzle ass’y (C) with the pipe (I) .
8. Connect the valve ass'y (B) to the tank (A) and mist
nozzle ass'y (C) , and fix them with 2 clips (N) .
(N)
(B)
(N)
(C)(I)
GB-6
(L)
(K)
(L)
TIGHTENING TORQUE
3.5 ± 0.5 N·m
Page 7
5. Operation
HOW TO USE
1. Pour the solution into the tank with the intermediate
valve closed.
WARNING
• Do not fill chemicals over 14 liters.
• Do not mix different chemicals.
2. Adjust the solution flow and the spray range according to work conditions.
The solution flow is changed by shifting the number
on the top of the valve at the mist nozzle. The figure
shows 5.5 lit/min. position.
Mist Kit for EBZ8000 / EBZ8001
Discharge rate
Valve travel (lit/min.)
1 1.0
2 2.1
3 3.8
4 5.5
Max. Longitudinal coverage
Horizontal direction : 22 m
Vertical direction : 14 m
6. Maintenance
WARNING
Make sure that the engine has stopped and is
cool before performing any service to the
blower. Contact with rotating blower fan or hot
muffler may result in a personal injury.
G
B
The spray range is changed by shifting the bell position after loosening the lock ring.
(A) Pulled out position: Long distance, narrow angle spray
(B) Pushed In position: Short distance, wide angle spray
3. Start the engine and carry the unit on your back.
4. While holding the swivel joint in your right hand, move
the throttle lever upward and turn the intermediate
valve to the open position.
5. After spraying work has finished, close the intermediate valve and stop the engine.
WARNING
• Before the solution spraying work, supply water into
the tank and operate the mister to make sure that there
is any leakage or any mechanical failure.
• Repair it if there is any leakage or failure before the
solution spraying work.
• Use only ZENOAH replacement parts. Failure to do
so may cause poor performance, possible injury and
may void your warranty.
• Inspect unit before each use for loose fasteners,
leaks, etc. Replace damaged parts.
GB-7
Page 8
Mist Kit for EBZ8000 / EBZ8001
7. Storage
On completion of all work procedures, when not planning to use again for a protracted period please carry
out the following pre-storage care, to prevent trouble
caused by time-lapse changes.
1. Clean the chemical fluid tank and nozzle.
2. Remove dirt from the sprayer, inspect it for any damage or looseness, and, if any abnormality is found,
correct it thoroughly in preparation for the next time
you use the unit.
3. Drain the fuel tank.
4. Start the engine, and leave it in idling condition until
all the fuel inside the carburetor is spent and the engine comes to a natural stop.
Limited warranty
Should any failure occur on the product under normal operating conditions within the applicable warranty period, the
failed part will be replaced or repaired free of charge by a
ZENOAH authorized dealer.
WARRANTY PERIOD: 1 year (6 months if used professionally, and 30 days if used for rental purpose) from the date of
initial purchase.
THE PURCHAS ER SHAL L BEA R COS TS OF T RANSPORTING THE UNIT TO AND FROM THE ZENOAH DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE ZENOAH DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE
PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.
5. Remove the spark plug and put a few drops (1~2 cc)
of 2-cycle oil inside the engine. After pulling the starter
rope 2 or 3 times, return the spark plugs to their original position and stop in compressed position.
6. After oiling the throttle lever and other metal parts with
anti-corrosive oil, cover the sprayer and store indoors
in a low-humidity location.
8. Disposal
When disposing your machine, fuel or oil for the machine,
be sure to allow your local regulations.
WARRANTY MAINTENANCE OR REPAIRS, AND SHALL
NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER
ENGINE COMPONENTS CAUSED BY THE FAIRURE OF A
WARRANTED PARTS STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS
WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL
FOR PROPER USE AND MAINTENANCE OF THE UNITS
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBRICATION, USE OF ANY PARTS OR ACCESSARIES OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE COMPANY’S
CONTROL.
THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES
IN THEIR APPEARANCE.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR
REPLACEMEN T AS REQUIRED M AIN TENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION
TO THE EFFECT OF REPAIR OR “REPLACE AS NECESSARY” SHALL BE WARRANTED FOR THE WARRANTY PERIOD. ANY WARRANTED PART WHICH IS SCHEDULED
FOR REPLACEME NT AS R EQUIRED MAINTENANCE
SHALL BE WARRANTED FOR THE PERIOD OF TIME UP
TO THE FIRST SCHEDULED REPLACEMENT POINT FOR
THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DULABILITY MAY BE USED IN NON-
GB-8
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO TWO (2) YEARS OF HOME USE
[ONE (1) YEAR FOR ANY OTHER USE] FROM THE ORIGINAL DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGE UNDER ANY AND ALL WARRANTIES ARE
EXCLUDED.
IF YOU NEED TO OBTAIN MORE INFORMATION, PLEASE
C A L L Y O U R N E A R E S T S E R V I C E C E N T E R ,
O R C H E C K P L E A S E Z E N O A H W E B S I T E
http://www.zenoah.net
Loading...