How it Works
Zebra Technologies
Loading...
AP716101
User Manual
52 pgs884.73 Kb0
Installation Guide
44 pgs1.02 Mb0
Table of contents
Loading...

Zebra Technologies AP716101, AP716102 Installation Guide

AP-7161 ACCESS POINT
INSTALLATION GUIDE
2 AP-7161 Access Point Installation Guide
AP-7161 Access Point Installation Guide 3
Motorola Solutions reserves the right to make changes to any product to improve reliability, function, or design.
Motorola Solutions does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Motorola Solutions Support at: http://supportcentral.motorola.com.
4 AP-7161 Access Point Installation Guide
Introduction.......................................................................................................................................... 3
Document Conventions........................................................................................................................ 3
Package Contents................................................................................................................................ 4
Hardware Installation........................................................................................................................... 5
Precautions.......................................................................................................................................... 5
Warnings.............................................................................................................................................. 5
Site Preparation................................................................................................................................... 6
Grounding Requirements..................................................................................................................... 6
AP-7161 Grounding Connection.......................................................................................................... 7
Ethernet and Lightning Protection........................................................................................................ 7
Access Point Placement...................................................................................................................... 7
Antenna Options.................................................................................................................................. 8
Installing an AP-7161......................................................................................................................... 10
Required Tools................................................................................................................................... 10
Mounting Bracket Options.................................................................................................................. 10
Extension Bracket.............................................................................................................................. 11
Pole Mounted Installations................................................................................................................. 13
Wall Mounted Installations................................................................................................................. 16
AP-7161 Connections and Ports.........................................................................................................18
Antenna Connectors........................................................................................................................... 18
Console, GE1/POE and GE2 Ports.................................................................................................... 19
Grounding Screw................................................................................................................................ 20
LED Indicators.................................................................................................................................... 21
Three Radio LEDs.............................................................................................................................. 22
Dual Radio LEDs................................................................................................................................ 23
Installing the Power-Over Ethernet (PoE) Unit................................................................................... 24
PoE Unit Specifications...................................................................................................................... 24
PoE Interface Connections................................................................................................................ 25
Installing the PoE Unit........................................................................................................................ 25
Basic AP-7161 Configuration............................................................................................................. 26
Specifications..................................................................................................................................... 26
Regulatory Compliance...................................................................................................................... 30
Country Approvals.............................................................................................................................. 30
Health and Safety Recommendations................................................................................................ 30
Warnings for the Use of Wireless Devices......................................................................................... 30
Potentially Hazardous Atmospheres.................................................................................................. 30
Safety in Hospitals............................................................................................................................. 30
RF Exposure Guidelines.................................................................................................................... 31
Safety Information.............................................................................................................................. 31
Reduce RF Exposure - Use Properly................................................................................................. 31
Remote and Standalone Antenna Configurations.............................................................................. 31
Power Supply..................................................................................................................................... 31
Wireless Devices - Countries............................................................................................................. 31
Country Selection............................................................................................................................... 31
Operation in the US............................................................................................................................ 31
AP-7161 Access Point Installation Guide 5
Radio Frequency Interference Requirements - FCC.......................................................................... 31
Radio Transmitters (Part 15).............................................................................................................. 32
Radio Frequency Interference Requirements - Canada..................................................................... 32
Radio Transmitters............................................................................................................................. 32
CE Marking and European Economic Area (EEA)............................................................................. 32
Statement of Compliance................................................................................................................... 32
Japan (VCCI) - Voluntary Control Council for Interference................................................................ 32
Korea Warning Statement for Class B............................................................................................... 33
Other Countries.................................................................................................................................. 33
Waste Electrical and Electronic WEEE.............................................................................................. 35
Motorola’s Enterprise Mobility Support Center................................................................................... 36
AP-7161 Series ROHS Compliance................................................................................................... 37
6 AP-7161 Access Point Installation Guide
AP-7161 Access Point Installation Guide 7

Introduction

The AP-7161 is a wireless broadband data system that uses mesh networking technology to support broadband data coverage. The system offers both 2.4 GHz 802.11b/g/n and 5.x GHz 802.11n Wi-Fi client access with 2.4 GHz 802.11 b/g/n and 5.x GHz
802.11a/n meshing. The dual-band system supports industry standard client devices and features easily deployed fixed infrastructure nodes.
The AP-7161 is also designed to extend the network with outdoor deployments. Deployments can be managed using the Motorola Solutions WiNG 5 architecture. The WiNG 5 architecture is a solution designed for 802.11n networking. It leverages the best aspects of independent and dependent architectures to create a smart network that meets the connectivity, quality and security needs of each user and their applications, based on the availability of network resources, including wired networks. WiNG 5 is a Third Generation WLAN solution – taking the best of both the first generation Autonomous access point WLAN and the second generation Centralized Controller Based WLAN.
The control plane is now distributed between the access points and the controllers. The network administrator has the flexibility of directing the data plane either being forwarded directly from the access points, or via the controllers. By distributing intelligence and control between the wireless controllers and APs, the WiNG 5 network can route directly via the best path, as determined by factors including the user, the location, the application and the available wireless and wired resources.
Once adopted by a Motorola Solutions RFS4000, RFS6000 or RFS7000 series controller, the AP-7161 is managed as an Adaptive AP running the WiNG 5 network management protocol. Motorola Solutions WiNG 5 Networks extend the differentiation that Adaptive APs offered to the next level by having the services and security now available at every point in the network. The traffic flow is optimized to prevent wired congestion as well as wireless congestion. Traffic flows dynamically, based on user and application, and finds alternate routes to work around any possible network choke points. Mixed-media application optimization is the hallmark of WiNG 5 networks.
For the latest version of this guide go to:http://support.symbol.com/support/product/manuals.do

Document Conventions

The following graphical alerts are used in this document to indicate notable situations.AP-7161
.
NOTE Tips, hints, or special requirements that you should take note of.
CAUTION Care is required. Disregarding a caution can result in data loss or equipment
malfunction.
WARNING! Indicates a condition or procedure that could result in personal injury or
equipment damage.
8 AP-7161 Access Point Installation Guide

Package Contents

Carefully remove all protective material from around the AP-7161 and save the shipping container for later storage and shipping.
Verify that you received the equipment listed below:
• AP-7161 access point
• Weatherproof RJ45 plug kit
• AP-7161 Access Point Installation Guide
Inspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment, contact the Motorola Solutions Support immediately.
AP-7161 Access Point Installation Guide 9

Hardware Installation

The AP-7161 access point has the following port designations:
• GE1/POE - LAN Port
• GE2 - WAN Port
• Console Port
An AP-7161 must be installed by trained professionals familiar with RF planning and regulatory limits defined by the regulatory bodies of the country where the devices are being deployed. All common precautions for grounding and ESD (Electrostatic Discharge) protection should be observed during deployment and installation. AP-7161 devices must be installed such that no harmful interference results from device operation.
CAUTION All device wiring must comply with the National Electric Code (NEC) or
regulations and procedures defined by the regulatory bodies of the country or region where the devices are being deployed. All local building and structure codes must be observed.
WARNING! Strictly observe the following Safety Warnings and Precautions when installing
an AP-7161 access point.

Precautions

Before installing an AP-7161 model access point verify the following:
• Become familiar with all grounding requirements (see Installing an AP-7161 on page 14)
• The grounding cable for an AP-7161 must be a #10 gauge wire cross section. The cable can be attached to the unit using one of the three recommended methods:
• Loosen the grounding screw, insert the grounding cable into the hole below it and tighten the screw.
• Loosen the grounding screw, wind the grounding cable around and tighten the screw.
• Attach a ring lug to the grounding cable and secure it to the unit using the grounding screw.
• Verify that the deployment environment has a continuous temperature range compatible with the operating temperature range of the device.

Warnings

• Read all installation instructions and site survey reports, and verify correct equipment installation before connecting the access point to its power source.
• Remove jewelry and watches before installing this equipment.
• Verify that the unit is grounded before connecting it to the power source.
• Verify that any device connected to this unit is properly wired and grounded.
• Connect all power cords to a properly wired and grounded electrical circuit. Verify that the electrical circuits have appropriate overload protection.
• Attach only approved power cords to the device.
• Verify that the power connector and socket are accessible at all times during the operation of the equipment.
10 AP-7161 Access Point Installation Guide
• Do not hold any component containing a radio such that it is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.
• Do not work with power circuits in dimly lit spaces.
• Do not install this equipment or work with its power circuits during thunderstorms or other weather conditions that could cause a power surge.
• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications.
• Avoid contact with overhead power lines.
• Take precautions to avoid injury from falling tools and equipment. Crews should wear hard hats in and around the installation work site.
• Be aware of vehicular traffic in and around the installation work site.
• Do not operate a portable transmitter near unshielded blasting caps or in an environment where explosives are present unless the transmitter is especially certified for such use.

Site Preparation

• Consult your site survey and network analysis reports to determine specific equipment placement, power drops, and so on.
• Assign installation responsibility to the appropriate personnel.
• Identify and document where all installed components are located.
• Identify and prepare Ethernet and console port connections.
• Verify that cable lengths are within the maximum allowable distances for optimal signal transmission.

Grounding Requirements

To avoid damage to the equipment, become familiar with Motorola Solutions Policy R56 before installing AP-7161 units. Refer to Standards and Guidelines For Communication Sites, Version B. Both the hardcopy manual (Part Number 68P81089E50-B) and the CD version (Part Number 9880384V83) can be ordered from Motorola Solutions.
Section 7.6.4 Broadband - Wireless Access Point Network from the Standards and Guidelines For Communication Sites applies directly to AP-7161 deployments: SPD (Surge Protection Device) considerations for broadband shall include the
use of SPDs to protect pole-mounted access points and ground-based cabinet architecture. It is important to install proper SPD applications on both ends of Ethernet, Power-Over Ethernet (POE), Giga-Ethernet (GigE) and AC cable runs. SPDs shall be located within the node or cabinet, or as close to the entrance as possible, and properly installed into load centers, control panels and utility power cabinets. While RF protection is a consideration, it shall only be required when antennas are connected to the node with coaxial cables greater than 610 mm (2 ft.) in length.
Lightning protection should be used on all shielded CAT-5E Ethernet connections.
An outdoor rated Lightning Protection Unit (LPU) kit such as the Motorola Solutions PTP WB2978AA or the HyperLink AL-CAT6HPJW Lightning Protector should be used.
NOTE Lightning damage is not covered under the conditions of a standard Motorola Solutions product
warranty. When installed correctly, LPUs provide the best protection from the harmful effects of lightning. Observe all regional and national codes that apply for lightning protection.
AP-7161 Access Point Installation Guide 11

AP-7161 Grounding Connection

The grounding cable for an AP-7161 must be a #10 gauge wire cross section.The grounding screw is located to the right of the GE1/POE port above the ground symbol.
The cable can be attached to the unit using one of the three recommended methods:
• Loosen the grounding screw, insert the grounding cable into the hole below it and tighten the screw.
• Loosen the grounding screw, wind the grounding cable around and tighten the screw.
• Attach a ring lug to the grounding cable and secure it to the unit by tightening the grounding screw.
When connecting the grounding cable to the unit, use an 8mm Socket and driver to tighten the grounding screw to between 21.9 and 29.2 inch pounds (lbf-in).

Ethernet and Lightning Protection

When installing an AP-7161, lightning protection should be used on all Shielded CAT-5E Ethernet connections. An outdoor rated Lightning Protection Unit (LPU) kit such as the Motorola Solutions PTP WB2907AA or the HyperLink AL-CAT6HPJW Lightning Protector should be used. For more information on Motorola Solutions PTP Lightning Protection Unit, refer to the PTP-LPU Technical Specifications.

Access Point Placement

Observe the following recommended guidelines to help ensure a successful network deployment:
• Mount the device with the black gore vent down.
• Mounting height for network devices should not exceed 30 to 35 feet. Mounting height should vary to accommodate the topography of the deployment area, foliage, and other obstructions.
• Devices can be deployed using any of the recommended outdoor Deployment Procedures.
• Line of sight (LoS) guidelines should be given special consideration whenever devices will not be installed in a straight line, such as deploying devices on alternating sides of a roadway.
12 AP-7161 Access Point Installation Guide

Antenna Options

Motorola Solutions supports two antenna suites for AP-7161 access points, one suite supporting the 2.4 GHz band and another suite supporting the 5 GHz band. Select a model best suited to the intended operational environment of your access point. The AP-7161 model access point can be purchased in a three radio configuration. If a three radio unit is purchased, the access point ships with two dual-band radios that should be connected to ports R3-A and R3-B. This is in addition to the other six antennas available to the access point’s other two radios. The single antenna supporting the third radio supports sensor mode only and can not function as a WLAN radio.
WARNING! Antenna ports where no antenna is mounted must be properly terminated using
an approved IP 67 terminator.
AP-7161 Access Point Installation Guide 13
The AP-7161 antenna suite includes the following models:
Antenna Description Band Gain
2,4 GHz, fixed DP, Omni, 80 dBi, Type N-M 2.4 8 19.5/495 ML-2499-FHPAG8-01
5.4 GHz, fixed DP, Omni, 10 dBi, Type N-M 4.9-5.8. 10 19.5/495 ML-5299-FHPAG10-01
Dual Band WIPS antenna 2.4, 5.2-5.8 4.5-7.5 11/280 ML-2452-HPAG5A8-01-01
4.9-5.9 GHz, fixed DP, 6 dBi,Type N-M 4.9-5.8 7.5 11/280 ML-5299-FHPA6-01R
2.4 GHz, fixed DP, 5DBI,Type N-M 2.4 5 - ML-2499-FHPA5-01R
2.4 GHz, downtilt 8 dBi, Type N-M 2.4 8 21/533 RAN4054A
Height
(in/mm)
P/N
14 AP-7161 Access Point Installation Guide

Installing an AP-7161

The following guidelines and procedures should be observed when installing an AP-7161:

Required Tools

The following is a list of the minimal tool set required to install an AP-7161:
• 8 mm socket and driver
• Torque wrench or ratchet with 10mm, 1/2 inch and 3/4 inch sockets.
• Adjustable wrench

Mounting Bracket Options

The mounting bracket kit and extension mounting hardware for the AP-7161 support several options for installation.
The AP-7161 mounting bracket kit contains:
Description Part Number Quantity
Mounting bracket section 1 SKJC120210-001 1
Mounting bracket section 2 SKJC120210-002 1
Mounting bracket section 3 SKJC120210-003 1
Serrated hex flanged screw, M6 x1.0 x 12 SKJC120210-004 8
Hex nut, 1/2inch - 13 thread SKJC120210-006 4
Hex head bolt, 1/2 inch - 13 thread x 3/4 inch SKJC120210-007 2
The three individual sections for the AP-7161 mounting bracket kit (P/N SKJC120210-001, -002 and -003) can be adjusted to rotate (plus or minus 15 degrees) and tilt (up to 45 degrees) during installation to orient the unit for optimum positioning.
Loading...
+ 30 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use