Zebra VC6000, VC6096, VC6090 Product Reference Guide

VC6000 SERIES VEHICLE COMPUTERS
PRODUCT REFERENCE GUIDE
VC6000 Series
Product Reference Guide
MN002219A01
Rev. A
ii VC6000 Series Product Reference Guide
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Zebra grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Zebra. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Zebra.
The user agrees to maintain Zebra’s copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof.
Zebra reserves the right to make changes to any software or product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any Zebra intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Zebra products.

Warranty

Subject to the terms of Zebra's hardware warranty statement, the VC6000 Series computer VC6000 Series products are warranted against defects in workmanship and materials for a period of one year from the date of shipment. For the complete Zebra hardware product warranty statement, go to:
www.zebra.com/warranty.

Revision History

Changes to the original manual are listed below:
Change Date Description
Rev A 11/30/2008 Initial release
Rev B 3/30/2009
Rev C 5/29/2012
Rev D 4/04/2013
Rev A 6/22/15 Zebra re-branding. Changed to new part number.
iii
iv VC6000 Series Product Reference Guide

Table of Contents

Warranty ............................................................................................................................................... ii
Revision History.................................................................................................................................... iii
About This Guide
About This Guide
Introduction ........................................................................................................................................... xiii
Documentation Set xiii
Configurations....................................................................................................................................... xiii
Software and Hardware Versions ......................................................................................................... xiv
Chapter Descriptions ............................................................................................................................ xv
Notational Conventions......................................................................................................................... xv
Related Documents .............................................................................................................................. xvi
Service Information............................................................................................................................... xvi
Chapter 1: Getting Started
Introduction .......................................................................................................................................... 1-1
Unpacking the VC6000 Series ............................................................................................................. 1-1
Optional Accessories ..................................................................................................................... 1-2
Model Configurations ........................................................................................................................... 1-3
Features ............................................................................................................................................... 1-3
Indication LEDs .................................................................................................................................... 1-6
System Indication LED ................................................................................................................... 1-6
Application LEDs ............................................................................................................................ 1-6
Getting Started ..................................................................................................................................... 1-7
Installing a SIM Card ...................................................................................................................... 1-7
Installing an SD Memory Card ....................................................................................................... 1-8
Installing the VC6000 Series .......................................................................................................... 1-8
Starting with the VC6000 Series .................................................................................................... 1-9
Standby Mode .......................................................................................................................... 1-9
Resume from Standby Mode ................................................................................................... 1-9
viii VC6000 Series Product Reference Guide
Controlling Screen Brightness ................................................................................................. 1-9
Controlling Keypad Illumination ............................................................................................... 1-9
Resetting the VC6000 Series ......................................................................................................... 1-10
Warm Boot ............................................................................................................................... 1-10
Cold Boot ................................................................................................................................. 1-10
Clean Boot ............................................................................................................................... 1-10
Function Keys ................................................................................................................................ 1-11
Chapter 2: Installation
Introduction .......................................................................................................................................... 2-1
Installing the VC6000 Series in a Vehicle ............................................................................................ 2-2
Guidelines for Routing Cables ....................................................................................................... 2-2
Mounting the VC6000 Series on Gas/Diesel-Powered Vehicles ......................................................... 2-3
Connecting the Vehicle Power Cable ............................................................................................ 2-3
Mounting the VC6090 on Electric-Powered Lift Trucks ....................................................................... 2-4
Access Requirements .................................................................................................................... 2-4
Important Mounting Information ..................................................................................................... 2-4
Telemetry Cables (VC6096 only) ................................................................................................... 2-6
Supported Bus Types .............................................................................................................. 2-6
6 Pin Deutsch Cable ................................................................................................................ 2-6
Auxiliary Port Pin layout ........................................................................................................... 2-7
Mounting the Combination Antenna (VC6096 only) ....................................................................... 2-10
Installing the GPS Antenna .................................................................................................................. 2-12
Mounting the VC6000 Series on AC-powered Carts and Stationary Installation ................................. 2-13
Optional Mounting ................................................................................................................................ 2-14
Free-standing Pedestal Mount ................................................................................................. 2-14
Desk Mount .............................................................................................................................. 2-14
Mounting Bracket Template for the VC6000 Series ....................................................................... 2-15
Lift Trucks ...................................................................................................................................... 2-16
Chapter 3: Operating the VC6000 Series
Introduction .......................................................................................................................................... 3-1
Using the Keyboard ............................................................................................................................. 3-2
Keyboard Functionality ........................................................................................................................ 3-3
Soft Keyboard ...................................................................................................................................... 3-4
Starting the Mobile Computer Boot Up ................................................................................................ 3-5
Today Screen ...................................................................................................................................... 3-5
Status Icons ......................................................................................................................................... 3-6
Programs ............................................................................................................................................. 3-8
Settings ................................................................................................................................................ 3-11
Adjusting Volume ................................................................................................................................. 3-14
Chapter 4: Using the Phone
Introduction .......................................................................................................................................... 4-1
Accessing the Phone Keypad .............................................................................................................. 4-1
Turning the Phone On and Off ............................................................................................................. 4-2
Audio Modes ........................................................................................................................................ 4-3
Table of Contents ix
Using a Bluetooth Headset ............................................................................................................ 4-3
Adjusting Audio Volume ................................................................................................................. 4-3
Making a Call ....................................................................................................................................... 4-4
Using the Phone ............................................................................................................................ 4-4
Using Contacts ............................................................................................................................... 4-4
Using Call History .......................................................................................................................... 4-5
Making a Speed Dial Call ............................................................................................................... 4-5
Making an Emergency Call .................................................................................................................. 4-6
Answering a Call .................................................................................................................................. 4-6
Incoming Call Features .................................................................................................................. 4-7
Smart Dialing ....................................................................................................................................... 4-7
Muting a Call ........................................................................................................................................ 4-8
Taking Notes ........................................................................................................................................ 4-9
Using Speed Dial ................................................................................................................................. 4-10
Adding a Speed Dial Entry ............................................................................................................. 4-10
Editing a Speed Dial Entry ............................................................................................................. 4-12
Deleting a Speed Dial Entry ........................................................................................................... 4-13
Using Call History ................................................................................................................................ 4-13
Managing Call History .................................................................................................................... 4-13
Changing the Call History View ............................................................................................... 4-14
Resetting the Recent Calls Counter ......................................................................................... 4-14
Deleting Call History Items by Call Date .................................................................................. 4-15
Deleting All Call History Items .................................................................................................. 4-15
Viewing Call Status .................................................................................................................. 4-16
Using the Call History Menu .................................................................................................... 4-17
Swapping Calls .................................................................................................................................... 4-17
Conference Calling .............................................................................................................................. 4-18
Text Messaging ................................................................................................................................... 4-20
Viewing Text Messages ................................................................................................................. 4-20
Sending a Text Message ............................................................................................................... 4-22
Chapter 5: Wireless Applications
Introduction .......................................................................................................................................... 5-1
Signal Strength Icon ............................................................................................................................ 5-2
Turning the WLAN Radio On and Off .................................................................................................. 5-3
Chapter 6: Using Bluetooth
Introduction .......................................................................................................................................... 6-1
Adaptive Frequency Hopping .............................................................................................................. 6-1
Security ................................................................................................................................................ 6-2
Turning the Bluetooth Radio Mode On and Off ................................................................................... 6-3
Disabling Bluetooth ........................................................................................................................ 6-3
Enabling Bluetooth ......................................................................................................................... 6-3
Bluetooth Power States ................................................................................................................. 6-4
Cold Boot ................................................................................................................................. 6-4
Warm Boot ............................................................................................................................... 6-4
Suspend ................................................................................................................................... 6-4
Resume .................................................................................................................................... 6-4
x VC6000 Series Product Reference Guide
Modes .................................................................................................................................................. 6-4
Wizard Mode .................................................................................................................................. 6-4
Explorer Mode ................................................................................................................................ 6-4
Discovering Bluetooth Device(s) .......................................................................................................... 6-6
Available Services ............................................................................................................................... 6-9
File Transfer Services .................................................................................................................... 6-10
Creating a New File or Folder .................................................................................................. 6-10
Deleting a File .......................................................................................................................... 6-11
Getting a File ............................................................................................................................ 6-11
Copying a File .......................................................................................................................... 6-11
Connecting to the Internet Using an Access Point ......................................................................... 6-11
Dial-Up Networking Services ......................................................................................................... 6-12
Object Exchange Push Services .................................................................................................... 6-12
Sending a Contact ................................................................................................................... 6-13
Swapping Contacts .................................................................................................................. 6-14
Fetching a Contact ................................................................................................................... 6-15
Sending a Picture ..................................................................................................................... 6-16
Headset Services ........................................................................................................................... 6-17
Hands-free Services ...................................................................................................................... 6-17
Serial Port Services ....................................................................................................................... 6-18
ActiveSync Using Serial Port Services .......................................................................................... 6-18
Personal Area Network Services ................................................................................................... 6-19
IrMC Synchronization Services ...................................................................................................... 6-19
Bonding with Discovered Device(s) ..................................................................................................... 6-20
Deleting a Bonded Device ....................................................................................................... 6-21
Accepting a Bond ..................................................................................................................... 6-21
Bluetooth Settings ................................................................................................................................ 6-21
Device Info Tab .............................................................................................................................. 6-22
Services Tab .................................................................................................................................. 6-22
Dial-Up Networking Service ..................................................................................................... 6-23
File Transfer Service ................................................................................................................ 6-24
Hands-Free Audio Gateway Service ........................................................................................ 6-25
Headset Audio Gateway Service ............................................................................................. 6-25
IrMC Synchronization Service .................................................................................................. 6-25
OBEX Object Push Service ..................................................................................................... 6-26
Personal Area Networking Service .......................................................................................... 6-27
Serial Port Service ................................................................................................................... 6-28
Security Tab ................................................................................................................................... 6-28
Discovery Tab ................................................................................................................................ 6-29
Virtual COM Port Tab ..................................................................................................................... 6-30
HID Tab .......................................................................................................................................... 6-31
Profiles Tab .................................................................................................................................... 6-31
System Parameters Tab ................................................................................................................ 6-32
Miscellaneous Tab ......................................................................................................................... 6-32
Chapter 7: GSM Configuration
Introduction .......................................................................................................................................... 7-1
Quick Startup Steps ............................................................................................................................. 7-1
VC6096 Service Verification ................................................................................................................ 7-2
Table of Contents xi
Ensuring Network Coverage .......................................................................................................... 7-2
Configuring a Data Connection ...................................................................................................... 7-3
Establishing a Data Connection ..................................................................................................... 7-5
Ending a Data Connection ............................................................................................................. 7-6
VC6096 Settings .................................................................................................................................. 7-7
Phone ............................................................................................................................................. 7-7
Sounds ..................................................................................................................................... 7-7
Security .................................................................................................................................... 7-8
Services ......................................................................................................................................... 7-9
Call Barring (Call Blocking) ...................................................................................................... 7-9
Caller ID ................................................................................................................................... 7-10
Call Forwarding ........................................................................................................................ 7-10
Call Waiting .............................................................................................................................. 7-11
Voice Mail and Text Messages ................................................................................................ 7-11
Fixed Dialing ............................................................................................................................ 7-12
Network .......................................................................................................................................... 7-12
Changing Networks Manually .................................................................................................. 7-13
Viewing Available Networks ..................................................................................................... 7-13
Setting Preferred Networks ...................................................................................................... 7-13
Phone Info ...................................................................................................................................... 7-14
Chapter 8: Using GPS Navigation
Introduction .......................................................................................................................................... 8-1
Software Installation ............................................................................................................................ 8-1
VC6096 GPS Setup ............................................................................................................................. 8-1
Operation ............................................................................................................................................. 8-2
GPS Maps on SD Cards ................................................................................................................ 8-2
Answering a Phone Call While Using GPS .................................................................................... 8-2
Losing the GPS Signal While in a Vehicle ..................................................................................... 8-2
Assisted GPS ....................................................................................................................................... 8-2
Chapter 9: ActiveSync
Introduction .......................................................................................................................................... 9-1
Installing and Setting Up ActiveSync ................................................................................................... 9-1
First Time Sync Connection ........................................................................................................... 9-1
Routine Sync Connection .............................................................................................................. 9-2
Chapter 10: Maintenance and Troubleshooting
Introduction .......................................................................................................................................... 10-1
Maintaining the VC6000 Series ........................................................................................................... 10-1
Cleaning ............................................................................................................................................... 10-2
Materials Required ......................................................................................................................... 10-2
Cleaning the VC6000 Series .......................................................................................................... 10-2
Housing .................................................................................................................................... 10-2
Display ..................................................................................................................................... 10-2
Connectors ............................................................................................................................... 10-2
Cleaning Frequency ....................................................................................................................... 10-3
xii VC6000 Series Product Reference Guide
Troubleshooting ................................................................................................................................... 10-4
Bluetooth Connection ..................................................................................................................... 10-5
Appendix A: Specifications
VC6096/VC6000 Specifications ........................................................................................................... A-1
Index
Glossary

About This Guide

Introduction

This guide provides information about using the VC6000 Series and accessories.
NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.

Documentation Set

The documentation set for the VC6000 Series is divided into guides provide information for specific user needs.
VC6000 Quick Reference Guide - describes how to start using the VC6000 Series.

Configurations

This guide covers the following configurations:
VC6000, VC6096, VC6090
xiv VC6000 Series Product Reference Guide

Software and Hardware Versions

This guide covers various software/hardware configurations and references are made to:
Operating system version
Hardware version
Fusion, Bluetooth and phone software versions
Hardware/software configuration
To determine the Operating System (OS) version:
Ta p Start > Settings > System info icon > System tab.
To determine the hardware version:
Ta p Start > Settings > System Info icon > HW Version tab.
To determine the Wireless LAN (Fusion), Bluetooth (OemBluetooth) and Wireless WAN radio (OemGSM) software software package information:
Ta p Start > Settings > System Info icon > Package tab.
To view the hardware and software configuration information:
Ta p Start > Settings > System Info icon > ConfigInfo tab.

Chapter Descriptions

Topics covered in this guide are as follows:
Chapter 1, Getting Started, provides information on getting the VC6000 Series up and running for the first time.
About This Guide xv
Chapter 2, Installation, provides instructions for installing the VC6000 Series in a vehicle or on a desktop. Provides instructions for installing accessories.
Chapter 3, Operating the VC6000 Series, explains how to use the VC6000 Series. This includes resetting the VC6000 Series entering data.
Chapter 4, Wireless Applications, provides instructions for using and configuring the VC6000 Series on a wireless LAN.
Chapter 5, Using Bluetooth, explains how to use Bluetooth functionality on the VC6000 Series.
Chapter 6, ActiveSync, provides instructions for installing and configuring ActiveSync.
Chapter 7, Maintenance and Troubleshooting, includes instructions on cleaning the VC6000 Series, and provides troubleshooting solutions for potential problems during VC6000 Series operation.

Notational Conventions

The following conventions are used in this document:
“VC6000 Series” refers to the Vehicle Computers 6000 and 6096.
Italics are used to highlight the following:
Chapters and sections in this and related documents
xvi VC6000 Series Product Reference Guide
Bold text is used to highlight the following:
Key names on a keypad
Button names on a screen or window.
Dialog box, window and screen names
Drop-down list and list box names
Check box and radio button names
Icons on a screen.
Bullets (•) indicate:
Action items
Lists of alternatives
Lists of required steps that are not necessarily sequential
Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
NOTE This symbol indicates something of special interest or importance to the reader. Failure to read the note
will not result in physical harm to the reader, equipment or data.
CAUTION This symbol indicates that if this information is ignored, the possibility of data or material damage may
occur.
WARNING! This symbol indicates that if this information is ignored the possibility that serious personal

Related Documents

VC6000 Series Quick Reference Guide, p/n 6802986C09.
Microsoft® Applications for Windows Mobile 6 User Guide, p/n 72E-108299-xx
ActiveSync software, available at: http://www.microsoft.com.
Application Guide, p/n 72E-68901-xx
Enterprise Mobility Developer Kits (EMDKs), available at: http://www.zebra.com/support.
For the latest version of this guide and all guides, go to: www.zebra.com/support.

Service Information

injury may occur.
If you have a problem with your equipment, contact Zebra Support for your region. Contact information is available at: www.zebra.com/support.
When contacting Zebra Support, please have the following information available:
About This Guide xvii
Serial number of the unit
Model number or product name
Software type and version number.
Zebra responds to calls by E-mail, telephone or fax within the time limits set forth in support agreements.
If your problem cannot be solved by Zebra Support, you may need to return your equipment for servicing and will be given specific directions. Zebra is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your business product from a Zebra business partner, contact that business partner for support.
xviii VC6000 Series Product Reference Guide
Chapter 1 Getting Started

Introduction

The VC6000 Series is a high-performing and rugged data communication and computing solution. It is specifically designed for the harsh conditions of the mobile environment areas that are not suitable for conventional notebook or desktop computers.
The computer enables real-time data access, collection, capture and report of information related to the driver’s workflow, status and location.
The fixed-mount computer consists of a touch-screen with an integrated QWERTY keyboard. Data can be entered using the touch-screen or keyboard.
The VC6000 Series has multiple communication capabilities that include: Wireless Local Area Network (WLAN), Wireless Wide Area Network (WWAN), Bluetooth
Bluetooth technology is used for cordless connection of peripheral devices such as printers, bar code scanners, handsfree speakers and headsets to the computer. Cellular and Wi-Fi radios are used to exchange voice and data with wide and local area networks. Among its many communication interfaces, the computer contains an internal GPS module, ensuring reliable and accurate vehicle location.

Unpacking the VC6000 Series

When you remove the VC6000 Series from its box, save the box and shipping material in case you need to ship or store it. Check the contents of the box against the invoice for completeness and contact your local Zebra service representative if there is a problem.
The VC6000 Series shipping box contains:
VC6000 Series vehicle computer
Hardware Kit (including five M4 installation screws)
Quick Reference Guide.
TM
and a Global Positioning System (GPS) receiver.
1 - 2 VC6000 Series Product Reference Guide
Inspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment, contact the Zebra Support immediately. See Service Information on page xvi for contact information.
NOTE A hardware kit that contains optional accessories is provided separately inside the shipping box.

Optional Accessories

Table 1-1 describes the optional accessories for all VC6000 Series devices.
Table 1-1
FLN4048 Combination Antenna
8508851K59 External GPS Antenna
PWRS-0102246H51R 100-240VAC Indoor Power Supply Unit.
Optional Accessories for All VC6000 Series Devices
Part Number Description
Use to power the VC6090 and VC6096 when it is fix mounted or installed on AC-powered carts.
23844-00-00R AC Cord (USA), grounded, 3-wire
3087568V84 VC6096 WWAN RF Cable (3m, 9.8ft.)
3087568V83 VC6096 WLAN RF Cable (3m, 9.8ft.)
3071815Y13 10-33VDC power cable with fuse, includes ignition sense. Use to power the
VC6090 and VC6096 from a gas/diesel-powered truck using 12V or 24V battery.
3071815Y15 9-Pin Deutsch Cable
3071815Y14 6-Pin Deutsch Cable
3071815Y88 RS232 and GPIO cable.
Supports (2) RS-232 connection, (8) digital inputs, (8) digital outputs, (2 analog inputs and DB9 connector to support a Telematic (VC6096 only) connectivity.
3089906V63 9-Pin Deutsch Telemetry Cable
3089906V61 6-Pin Deutsch Telemetry Cable
0771837Y26 Sapphire Mounting Adaptor
RAM-246U RAM mount VESA100 C-size (1.5") ball, 4.75 SQ. Requires a RAM mount arm
and base (sold directly by RAM mount).
PWRS-14000-251R DC-to-DC converter, 18 to 75VDC, including a power cable with fuse. Use to
power the VC6090 on electric lift trucks with 24V, 36V and 48V batteries.
30013095001 Power Cable, VC6090 to PWRS-14000-251R DC-to-DC Converter
23844-00-00R US AC line cord, grounded, three wire for power supplies PWRS-14000-148R and
PWRS-14000-241R as well as PWRS-0102246H51R

Model Configurations

Table 1-3 describes the VC6000 Series model configurations.
Getting Started 1 - 3
Table 1-2
Operating System Windows Mobile
GPS No Yes No
Bluetooth (BT) Yes Yes Yes
Wireless LAN No Yes
Cellular Radio (HSDPA, UMTS, GSM, GPRS, EDGE) No
Vehicle Telemetry No Yes No
Internal BT Antenna Yes Yes Yes
Internal WLAN Antenna No No Yes

Features

The VC6000 Series has the following features:
VC6000 Series - Model Configurations
Table 1-1.
Configuration Model VC6000 VC6096 VC6090
Windows Mobile
6.5 Classic
6.5 Professional
(802.11 a/b/g)
(Voice and
Yes
data)
Windows Mobile
6.5 Classic
Yes
(802.11 a/b/g)
No
Ergonomic design with a color LCD touch screen
Windows Mobile 6.5 operating system
Internal Bluetooth radio to enable wireless connection to a Bluetooth printer, bar code scanner, headset and other Bluetooth peripherals
Connection to WLAN in 802.11a/b/g standards (VC6090 and VC6096)
Connection to WWAN using a Global Positioning System (GSM) for mobile communication, cellular radio and High-Speed Downlink Packet Access (HSDPA) (VC6096 only)
10/100 Ethernet port for connection to Local Area Network (LAN)
Vehicle motion and location detection via the vehicle telemetry and the GPS receiver (VC6096 only)
Serial RS232 interface and GPIOs
Two full speed USB ports (One with 1A power output, VC6090 only)
Flexible power options:
- Direct 10V to 33Vdc, with ignition sense for gas/diesel-powered lift trucks and vehicles with 12V or 24V battery.
- External 18 to 75V DC-to-DC converter for electric-powered lift truck with 24V, 36V or 48V battery (VC6090 only).
- External 100 to 240VAC power supply for AC-powered carts and stationary installation.
Reliable operation in cold environments, as low as -20 °C (- 4 °F)
1 - 4 VC6000 Series Product Reference Guide
Volume up/down Key
Application LEDs - two Green LEDs Driven by Application
2
Power Button with System Indication LED
1
Brightness up/down Key
Microphone (embedded)
Full QWERTY Keypad
3
Left Soft Key
4
Right Soft Key
4
Call Key (Model VC6096)
5
Home Key (Model VC6000)
End Key (Model VC6096)
6
Back Key (Model VC6000)
Navigation Key
Select Key
Speaker (embedded)
Function Keys
7
Touch Screen
Maximum operational temperature 60 °C (140 °F)
Figure 1-1
Front View
1
See System Indication LED on page 1-6.
2
For LED indications, refer to Application LEDs on page 1-6.
3
VC6090 numeric keys also marked as F1-F20 function keys (with Ctrl / Alt keys)
4
For key function, refer to the text displayed on the screen.
5
Model VC60x0-Home key. Model VC6096-Call key (For Home, press Fn+H keys).
6
Model VC60x0-Back key. Model VC6096-End key (For Back, press Fn+J keys).
7
For keys operation, refer to your application guide.
Getting Started 1 - 5
Auxiliary Port
3, 4
M4 Ground Screw Boss
5
M4 Screw Mounting Bosses
Power Connector
GPS Antenna Connector
(used in VC6096 only)
WWAN Antenna Connector
1
(used in VC6096 only)
WLAN Antenna Connector
1, 2
(used in VC6096 only)
Mini USB Port, Type B
2
USB Port, Type A
3
10/100 Ethernet LAN Port
2, 6
SIM Card Slot
3
(used in VC6096 only)
USB Port, Type A
3
SD Memory Card Slot
3
Cable Retention Bracket
Host USB port, type A
3
Client mini USB port, type B
3
Figure 1-2
1. Only for VC6096.
2. Reverse thread - rotate counterclockwise to fasten connector.
3. 1A power output (VC6090 only). Keep covered when not in use.
4. Includes: 8 digital inputs, 8 digital outputs, 2 analog inputs, 2 pins for debugging, 2 full RS232, CAN2.0 - J1939
(Telemetry), J1708 (Telemetry). Note that VC6090 does not support telemetry.
5. To avoid damage to the boss threads, use only the supplied screw.
6. To activate the 10/100 Ethernet LAN Port, refer to Ethernet LAN Power program in Table 3-5 on page 3-9.
Back View
1 - 6 VC6000 Series Product Reference Guide
Indication LEDs

System Indication LED

The system indication LED is located inside the Suspend Button.
Table 1-3 describes the LED indications.
Table 1-3
Off
Fast flashing amber
Slowly flashing amber
LED Indications
LED State Indication
Normal operation.
Critical power event. Input power is out of operating range. The computer may turn off - save your entries.
Vehicle engine start - no action is required.
Cold reset is active - no action is required.
Critical temperature event. Ambient temperature is out of operating range -20 °C to 60 °C (-4 °F to 140 °F). The VC6000 Series may turn off.

Application LEDs

The Application LEDs are located on the upper left hand side of the VC6000 Series front panel.
To know more about the function of Application LEDs, refer to the operating manual provided by your organization.
Getting Started
SIM Card
SIM Slot
SIM Card Door
T8 Screw
In order to start using the VC6000 Series for the first time:
Install a SIM Card (VC6096 only, when cellular communication is required)
Install an SD Memory Card (optional)
Install the VC6000 Series in a vehicle or on a desktop.
Start the VC6000 Series.

Installing a SIM Card

Before using the VC6096 in a cellular network, make sure that the VC6096 is equipped with a Subscriber Identity Module (SIM) card, obtained form your service provider. The SIM card is a small smart card that fits into the VC6096. The SIM card holds the personalized information about the VC6096, including network activation and phone book entries.
To install the SIM card:
Getting Started 1 - 7
1. Remove the T8 screw that secures the SIM card door and open the door.
2. Position the SIM card with the contacts facing the back of the VC6096, and insert into the SIM slot. The SIM
card corner notch fits into the slot only one way (see Figure 1-3).
3. Use a pen to push the SIM card inwards to lock.
4. Place the SIM card door and secure the T8 screw.
NOTE The VC6096 powers on only if the T8 screw is fully secured.
5. Torque the T8 screw to 3.4 kgf-cm (3 in-lbs).
Figure 1-3
CAUTION Ensure to torque the screw to seal the VC6000 Series properly. Otherwise, sealing can be
SIM Card Installation
compromised.
1 - 8 VC6000 Series Product Reference Guide
SD Memory Card
Memory Card Slot
Protective Rubber Cap

Installing an SD Memory Card

A Secure Digital (SD) memory card provides secondary non-volatile data storage. Use MMC and non-SDHC SD memory cards. The card slot is located on the side panel of the VC6000 Series.
To install the SD memory card:
1. Lift up the Protective Rubber Cap that covers the Memory Card Slot.
2. Position the SD memory card with the contacts facing the back of the VC6000 Series and insert into the
Memory Card Slot. The corner notch of the SD memory card fits into the Memory Card slot only one way.
3. Use a pen to push the SD memory card inwards to lock.
4. Replace the Protective Rubber Cap to seal the Memory card slot.
Figure 1-4
SD Card Installation

Installing the VC6000 Series

Refer to Chapter 2, Installation for information on installing the VC6000 Series onto a vehicle or on a desktop, as well as installing accessories.
Getting Started 1 - 9
Power Button
Starting with the VC6000 Series
The VC6000 Series is automatically powered on when connected to the vehicle or desktop power supply. The VC6000 Series turns to Standby mode when the vehicle is turned off. In Standby mode, the screen automatically turns off after some time.
Standby Mode
Standby mode is a power saving mode enabled only when the vehicle ignition key is switched to the OFF position.
In Standby mode, the screen display and backlight illumination automatically turn off after a period of two minutes when VC6000 Series is not active.
Figure 1-5
Power Button
Resume from Standby Mode
To resume from Standby mode, press any key, touch the screen or momentarily press the Power Button .
The VC6000 Series can be programmed to automatically resume from Standby mode when: turning On the ignition key, connecting or removing a USB device, pressing a keyboard key, receiving an alarm, pressing the touch screen, communicating over Bluetooth, communicating over WWAN, Telemetry signal (1939 protocol only), Ethernet signal (magicPacket), GPIO signal.
To program the operation of Standby mode, refer to the VC6000 Series Software Enterprise Mobility Developer Kit for C (EMDK).
Controlling Screen Brightness
There are five levels of screen brightness.
To adjust the brightness of the screen, press the Brightness down button to decrease the brightness or the Brightness up button to increase the brightness.
Controlling Keypad Illumination
There are five levels of keypad illumination. To adjust the keypad illumination:
1. Press the Ctrl key to lock in down position.
2. Press the Brightness up/down key to increase/decrease the keypad illumination.
3. Press the Ctrl key to unlock in up position.
1 - 10 VC6000 Series Product Reference Guide

Resetting the VC6000 Series

If the VC6000 Series stops responding to inputs, perform the reset actions in the following order:
Warm Boot
Warm boot may become necessary when an application running on your VC6000 Series does not respond after performing initial reset.
CAUTION Warm boot may cause lost of information from programs currently running on the computer.
To perform warm boot:
Press and hold the Power Button for five seconds and release.
Cold Boot
Cold boot may become necessary when your VC6000 Series is jammed and does not respond after performing warm boot.
Cold boot restarts the VC6000 Series by performing an ungraceful shutdown of all running applications and powering off the VC6000 Series. Cold boot resets information stored in all running applications. Data saved on flash memory or a memory card is not lost.
To perform a cold boot:
Press and hold + + Power Button .
You can also perform cold boot by holding the Power Button pressed for 25 seconds.
Clean Boot
CAUTION A clean boot should only be performed by an authorized system administrator. Removing power from
the VC6000 during a clean boot may render the VC6000 inoperable.
Clean boot may become necessary when your VC6000 Series is jammed and does not respond to cold boot.
A clean boot resets the VC6000 Series to the factory default settings. All applications installed by your organization are erased and should be re-installed on the VC6000 Series. Before performing a clean boot, download the Clean Boot Package files from the Support Central web site.
The Clean Boot Package include the following files:
Cleanps.bin: to clean the persistent storage
CleanAppl.bin: to clean the application volume
Pkgs.Lst: control file to select the file to be programmed.
To perform a clean boot:
1. Download the Clean Boot Package from the Support Central web site. Follow the updated instructions included
in the package for installing the package onto the VC6000 Series.
2. Copy the attached files to either the SD memory card root directory (if used) or the VC6000 Series Temp
directory.
Getting Started 1 - 11
3. Press and hold + + Power Button + Left Soft key .
4. Immediately, as soon as the VC6000 Series starts to boot and before the splash screen is visible, release all
keys and press and hold the left soft key.
5. Within the popup 'IPL' menu displayed on the screen, make sure the Update Loader line is marked and then
release the Soft key.
6. At the end of the clean boot programming you should see the Windows Mobile calibration screen.

Function Keys

The five function keys on the front right hand side of the panel can be set to perform dedicated functions, such switching between different software application screens. To know more about the function of each key, refer to your application guide. To program the operation of the Function keys, refer to the VC6000 Series Software Enterprise Mobility Developer Kit for C (EMDK).
1 - 12 VC6000 Series Product Reference Guide
Chapter 2 Installation

Introduction

This chapter describes how to install the VC6000 Series in a vehicle or on a desktop and connecting the VC6000 Series to a power source. This chapter also describes how to install the various accessories for the VC6000 Series. Read all of the following instructions before you begin.
WARNING! To avoid injury, the VC6000 Series must be firmly secured to a surface of the vehicle that can
support the VC6000 Series weight in extreme driving conditions. Do not install the VC6000 Series or any accessory in a location that affects the vehicle safety, driveability, or visibility.
CAUTION The installation of the VC6000 Series should be performed in accordance with your organization
procedures and requirements.
A competent engineer must perform the installation in a vehicle. Improper installation can damage your vehicle and/or the VC6000.
2 - 2 VC6000 Series Product Reference Guide
Cable Tie Bracket
Figure 2-1
Cable Tie Bracket
Installing the VC6000 Series in a Vehicle

Guidelines for Routing Cables

Establish a neat route for the cable, staying clear of moving parts or hot surfaces.
Fix the cable to an existing cable runs inside the vehicle using cable ties.
When the cabling must go through a panel, use a suitable cable guard.
When fixing a conduit or a cable on the outside of a vehicle, use P-Clips. Either drill and tap the hole or use a nut and bolt to secure the clip.
Ensure the cable does not have tight bends. The minimum recommended radius is 6.35 cm (2.5 inches).
Ensure cables do not swing or chafe on the structure. This often requires using cable ties approximately every one foot, and ensuring the cables do not flex often, especially where they connect to the VC6000 series.
If you must re-position the VC6000 series occasionally, ensure there is enough slack in the cable to accommodate movement without putting tension on the cable.
Use plastic cable ties to secure the cables to the Cable Tie Bracket of the VC6000 (see Figure 2-1).
Connect the power as close to the battery as possible, but not directly from the battery terminals, and not before any main fuse.
On gasoline, diesel or propane electric lift trucks, connect the power as close to the battery terminals as possible, and avoid using existing wiring.
Ensure that the fuse is as close as possible to the power source.
The fuse must be securely mounted and in an accessible location.
Do not install where the cable will be a trip hazard or interfere with safety of day-to-day activities or otherwise create a hazardous condition.
Fix the cable to existing cable runs inside the electric lift truck using cable ties, but make sure they are away from any moving or hot surfaces.
If the VC6090 needs to be re-positioned, be sure there is enough slack in the cable to accommodate movement without putting tension on the cable.
DO NOT wind a cable in and out of the mesh on a cage.
DO NOT route the cables on the outside of the electric lift truck or areas where the electric lift truck may come in contact with objects.
CAUTION Shortening or modifying the cable and/or by-passing the in-line fuse voids the product warranty, nullifies
the product UL safety mark, and may result in a hazardous condition. Do not modify the cable under any circumstance.
CAUTION The VC6000 series should operate only in negative ground electrical systems. Check the ground polarity
of the vehicle before starting the VC6000 series installation to verify that the polarity is correct. Accidentally reversing the polarity will not damage the VC6000 series, but will cause the cable fuse to blow.
Mounting the VC6000 Series on Gas/Diesel-Powered Vehicles
Power - Red Wire
Ground - Black Wire
Ignition - Green Wire
10 A Fuse SLO BLO
Power Plug
Pin 1 - Power Pin 2 - Ignition Pin 3 - N.C Pin 4 Ground
Shrink Tubing
Fuse Holder
Direct 10V to 33Vdc, with ignition sense for gas/diesel-powered lift trucks and vehicles with 12V or 24V battery.

Connecting the Vehicle Power Cable

CAUTION DO NOT install the VC6000 Series in a vehicle with a positive ground electrical system.
To connect the power cable (see Figure 2-2):
1. Disconnect the power terminals from the vehicle battery.
CAUTION Failure to disconnect the battery before installing the power converter may result in the injury or death
of the installer by electric shock.
2. Connect the black wire to the vehicle’s negative power source.
3. Connect the green wire to the vehicle’s ignition switch.
Installation 2 - 3
4. Connect the red wire to the vehicle’s positive power source. Place a 10 A slow blow fuse inside the fuse holder,
connected in-line with the red wire approximately 4” from the cable end, as shown in the figure below.
5. Connect the cable’s Power Plug to the VC6000 Series Power Connector (PWR) (see Figure 2-2) and turn
clockwise to lock. The length of the cable is 9.8 ft. (3 m).
Figure 2-2
6. When routing wires, slide Shrink Tubing over wires as required.
7. Connect the power terminals of the Vehicle Power Cable to the terminals of the vehicle battery.
8. Reconnect the vehicle battery.
Power Cable
2 - 4 VC6000 Series Product Reference Guide
Cap Screws (4x)
DC Cable
Flat Washers (4x)
Nyloc Nuts (4x)
Figure 2-3
Mounting the Power Converter
on an Electric-Powered Lift Trucks
Mounting the VC6090 on Electric-Powered Lift Trucks
When installing the VC6090 on an electric-powered lift truck with 24V, 36V or 48V batteries, an external 18-75V DC-to-DC converter is required.

Access Requirements

NOTE Do not directly connect the VC6090 to the electric lift truck battery without the DC-to-DC converter.
Determine the best location for mounting the power converter, taking into consideration the ease of accessing the power converter and mounting requirements.
Make sure that you have access to the power converter’s power-out connection.

Important Mounting Information

Mounting surface must be flat and rigid and it must extend evenly for the entire length of the power converter surface.
All four mounting holes must be used.
Use the following mounting hardware to mount the Power Converter:
1. Four stainless steel cap screws, 1/4”-20-X (M6x1.0-X) where X represents the length of the cap screws.
2. Four 1/4”-20 (M6x1.0) nyloc nuts
3. Four 1/4” (M6) flat washers
When installing the power converter, care must be taken to ensure that the mounting surface is fully supported. Additional plates may be required to
achieve this.
CAUTION If mounting to a thin surface, a
reinforcing plate is required.
• Check that any attached cables are routed so that they do not
interfere with the operation of forks or other moving parts.
To connect the Electric Lift Truck Power Converter to power:
NOTE See the electric lift truck Owner's Manual for specific wiring information.
1. Disconnect the fork lift battery.
2. Connect the Power Converter to the vehicle battery as shown below
3. Confirm the fuse is in the fuse mount:
For a 12V or 24V fork lift, use a 8A fast blow ceramic fuse.
Installation 2 - 5
For a 36V, 48V, or 60V fork lift, use a 5A fast blow ceramic fuse.
4. Route the cable from the power converter to the power source using the Cabling Installation Guidelines (See
Guidelines for Routing Cables on page 2-2).
5. Connect the red wire to the electric lift truck's positive power source. Connect the black wire to the electric lift
truck's negative power source.
6. Ensure the wiring connections created are sufficiently insulated from each other.
7. Reconnect the electric lift truck battery.
2 - 6 VC6000 Series Product Reference Guide
J1 to VC6000 Series Auxiliary Port
J2 RS232 (D-type -
Male) Connector
J3 Deutsch 6 Pin Telemetry Connector (HD16-6-12s)
I/O Wires: 8 digital inputs, 8 digital outputs, 2 analog inputs, Debug (2 wires for debugging). See label on wires. Maximum current through wires 0.5 A

Telemetry Cables (VC6096 only)

The VC6096 vehicle telemetry system enables remote access to information and services relating to the operation and performance of a vehicle. Information from the vehicle telemetry circuit is received via wire communication and processed by VC6096. The driver then access the computer application menus, such as the Web browser or GPS, in order to obtain various telemetry data relating to the vehicle(s).
Vehicle telemetry information is also used for maintenance and diagnose of the vehicle condition
.
The VC6096 is equipped with a built in (on–board) capability to interface with Heavy-Duty type bus (SAE J1708, J1939) without an external adapter. Vehicle bus type can be selected manually or automatically via API.
Supported Bus Types
The VC6096 supports communication with the following Vehicles Telemetry Bus types (see Table 2-1):
Table 2-1
Vehicles Telemetry Bus Types
Table 2-1.
Vehicle Bus Type
(Including data link & network layers)
Physical Layer
Protocol Layer
Heavy-Duty Vehicle SAE J1708 SAE J1587
Heavy-Duty Vehicle SAE J1939-21 (CAN2.0) SAE J1939-71
Heavy-Duty Vehicle SAE J1708 SAE J1587
6 Pin Deutsch Cable
1. Connect J1 connector into the Auxiliary port of the VC6000 Series (see Figure 2-4). Fasten the connector’s
screws.
2. Connect J2 - J3 plugs to the telemetry receptacles of your vehicle data bus.
3. Connect the I/O Wires as required (see Table 2-2).
Figure 2-4
6 Pin Deutsch Cable
Installation 2 - 7
Auxiliary Port Pin layout
For connecting the I/O wires, use the I/O wires labels and the Auxiliary connector pinout detailed in Table 2-2 below.
Table 2-2
1
3
5
7
9
11
15
2
4
Auxiliary Connector Pinout Details
Pin # Name Functionality
RD_OUT1 General purpose output port for relay drive (maximum current load 0.5A)
Relay state restores to initial position after Warm or Cold boot.
RD_OUT2 General purpose output port for relay drive (maximum current load 0.5A)
Relay state restores to initial position after Warm or Cold boot.
RD_OUT3 General purpose output port for relay drive (maximum current load 0.5A)
Relay state restores to initial position after Warm or Cold boot.
RD_OUT4 General purpose output port for relay drive (maximum current load 0.5A)
Relay state restores to initial position after Warm or Cold boot.
RD_OUT5 General purpose output port for relay drive (maximum current load 0.5A)
Relay state restores to initial position after Warm or Cold boot.
RD_OUT6 General purpose output port for relay drive (maximum current load 0.5A)
Relay state restores to initial position after Warm or Cold boot.
RD_OUT8 General purpose output port for relay drive (maximum current load 0.5A)
Relay state restores to initial position after Warm or Cold boot.
DI_SP0
DI_SP1
General purpose digital input port1 (switch detect, 5,12 or 24V inputs). Negative sense to either vehicle Ground or battery negative terminal.
General purpose digital input port1 (switch detect, 5,12 or 24V inputs). Negative sense to either vehicle Ground or battery negative terminal.
6
8
10
12
14
16
17
18
19
20
DI_SP2
DI_SP3
DI_SP4
DI_SP5
DI_SP6
DI_SP7
UART_Tx/XCVR Debugging port for maintenance only.
UART_Rx/XCVR Debugging port for maintenance only.
ANALOG19 Sense of analog input signal 1 2 (positive terminal)
ANALOG GND Ground point
General purpose digital input port1 (switch detect, 5,12 or 24V inputs). Negative sense to either vehicle Ground or battery negative terminal.T
General purpose digital input port1 (switch detect, 5,12 or 24V inputs). Negative sense to either vehicle Ground or battery negative terminal.
General purpose digital input port1 (switch detect, 5,12 or 24V inputs). Negative sense to either vehicle Ground or battery negative terminal.
General purpose digital input port1 (switch detect, 5,12 or 24V inputs). Negative sense to either vehicle Ground or battery negative terminal.T
General purpose digital input port1 (switch detect, 5,12 or 24V inputs). Negative sense to either vehicle Ground or battery negative terminal.
General purpose digital input port1 (switch detect, 5,12 or 24V inputs). Negative sense to either vehicle Ground or battery negative terminal.
2 - 8 VC6000 Series Product Reference Guide
Table 2-2
21
22
23
24
25
26
27
28
29
30
31
32
33
Auxiliary Connector Pinout Details (Continued)
Pin # Name Functionality
ANALOG21 Sense of analog input signal 2 2 (positive terminal)
ANALOG GND Ground point
GND Ground point
GND Ground point
BAT_POS Vehicle battery output (maximum current load 0.5A)
GND Ground point
GND Ground point
GND Ground point
RS232 Port 1 RxD
RS232 Port 1 TxD
RS232 Port 1 RTS
RS232 Port 1 CTS
RS232 Port 1 DSR
34
35
36
37
38
39
40
41
42
43
44
45
46
RS232 Port 1 DTR
RS232 Port 1 CD
RS232 Port 1 RI
RS232 Port 2 RxD
RS232 Port 2 TxD
RS232 Port 2 RTS
RS232 Port 2 CTS
RS232 Port 2 DSR
RS232 Port 2 DTR
RS232 Port 2 CD
RS232 Port 2 RI
J1708_P J1708 Telemetry Communication port for receiving and transmitting data
to the ECU’s (Electronic Control Unit) over vehicle bus (positive terminal). Non functional in VC6000
J1708_N J1708 Telemetry communication port (negative terminal)
Non functional in VC6000
47
CAN2B_P J1939 telemetry communication port with vehicle bus (positive terminal)
Non functional in VC6000
Installation 2 - 9
Table 2-2
Auxiliary Connector Pinout Details (Continued)
Pin # Name Functionality
48
CAN2B_N J1939 telemetry communication port (negative terminal)
Non functional in VC6000
49
CAN_Shield CAN Shield (RC to GND)
Non functional in the VC6000.
50
1
To program the operation of input/output, refer to Enterprise Mobility Developer Kits (EMDKs).
2
To program minimum and maximum thresholds for port notification, refer to the VC6000 Series Software Developer
GND GND
Kit for C (SDK).
2 - 10 VC6000 Series Product Reference Guide
Vehicle Windshield
or
WWAN Cable Connector (Keep covered when not in use).
WLAN Cable Connector (Keep covered when not in use).
Lower Cables Bracket
Upper Cables Bracket
M4 Screws (x2)
Screw Inserts (x2)
Antenna Bracket Inserts (x3)

Mounting the Combination Antenna (VC6096 only)

The Combination Antenna is an optional omni-directional WWAN and WLAN antenna used with the VC6096. The antenna mounts inside/outside the vehicle cabin or indoors/outdoors (see Figure 2-6).
Figure 2-5
Combination Antenna - Vehicle Mount
The antenna has two external RF connectors that connect to the VC6096 via two low loss RF coax cables
CAUTION To avoid damage to the VC6096, make sure to disconnect the power cable from the VC6096 before
connecting the antenna cable. When installing the antenna cable, make sure to connect the antenna side of the cable before connecting to the VC6096.
To install the Combination Antenna (see Figure 2-6):
1. Connect the WWAN and WLAN Cable
Connectors.
2. Place the Lower Cables Bracket under the
cables so that the two holes align with the
screw inserts on the antenna.
3. Place the Upper Cables Bracket on top of the
4. Align the two holes on the Upper and Lower
WWAN and WLAN Cable Connectors.
Cables Brackets with the screw inserts and
secure the two M4 Screws (Torque 5 in-lbs).
5. Use the three (x3) Antenna Bracket Inserts to
mount the antenna. Secure the antenna using
three M4 screws.
Figure 2-6
Combination Antenna - Installation Guidelines
Installation 2 - 11
Combination antenna installation guidelines (see Figure 2-6):
1. For best performance, it is recommended to install the antenna outside of the cabin. When installing the
antenna in the vehicle cabin or indoors, keep a minimum distance of 70 cm (2.3 ft.) between the antenna and
the VC6096.
2. The antenna should be directed vertically to the horizon to assure maximum exposure.
3. To ensure best performance, the antenna should be mounted as far away as possible from walls, floors and
metal containing objects. Keep an obstacle free zone of 10 cm (3.9 inches) from walls, cabinets, air duct,
metal-framed windows, doors etc.
4. When mounting the antenna inside the vehicle, it is recommended to install the antenna at the top right hand
side of the windshield.
WARNING! 1. Keep a minimum lateral distance of 20 cm (8 inches) between the driver/passenger and the antenna.
Contact your professional installer, VAR, or antenna manufacturer for proper installation requirements.
2. To ensure safe driving, when mounting the Combination Antenna next to the windshield, do not block the driver’s field of view.
2 - 12 VC6000 Series Product Reference Guide
GPS Antenna
Metal Plate

Installing the GPS Antenna

The VC6096 is supplied with an internal module of Global Positioning System (GPS).
Connect the cable connector of the GPS antenna to the GPS connector at the back of the VC6096 (see Figure 1-2
on page 1-5).
CAUTION To avoid damage to the VC6000 Series, disconnect the power cable from the VC6000 Series before
connecting the antenna cable.
GPS antenna Installation guidelines (see Figure 2-7):
1. Recommended GPS antenna - Zebra part number 8508851K59.
2. The GPS antenna must be installed on the top of the dashboard or on vehicle roof (see Figure 2-7). For best
performance, install the GPS antenna on the center-line of the vehicle roof.
3. Keep a minimum distance of 40 cm (16”) between the Combination antenna and the GPS antenna.
4. The antenna is attached by a magnet to a flat metal surface. Before installing the GPS antenna on a
dashboard, install a flat Metal Plate (minimum 2.75” x 2.75”, 7cm x 7 cm) on the dashboard to hold the GPS
antenna.
5. The antenna should be directed parallel to the horizon to assure exposure to as many GPS satellites as
possible.
6. If possible, the antenna location must not be obstructed by any structure or object. When installing the antenna
on a roof, ensure at least 3” of clear space around it.
Figure 2-7
GPS Antenna Installation
Installation 2 - 13

Mounting the VC6000 Series on AC-powered Carts and Stationary Installation

AC-powered carts and stationary installation are powered using an a 100 to 240VAC Indoor Power Supply Unit.
To connect the VC6000 Series Indoors (see Figure 2-8):
1. If installed indoors, connect a ground wire between the VC6000 series and the facility ground system. The
ground wire ring lugs should be connected to the Ground Point (GND) on the back of the VC6000 series using
M4 screw.
The ground wire ring lugs should be connected to the Ground Point (GND) at the back of the VC6000 Series
using M4 screw.
NOTE Grounding the unit is optional. To ground the unit, use a 18AWG ground wire between the VC6000 series
Ground Point (GND) and the facility ground system. To avoid damage to the boss threads, use only the supplied M4 screw.
2. Attach the 12 V DC cable of the Indoor Power Supply Unit to the Power Connector at the back of the VC6000
Series and turn clockwise to lock. Rotate clockwise to lock the connector.
3. Connect the AC Cord into the Indoor Power Supply Unit.
NOTE The total length of the power supply cables is 14.1 ft (4.3 m).
4. Connect the AC Cord plug into a 100-240 V AC / 50-60 Hz power outlet.
5. Mount the Combination Antenna outdoors. Contact the mast of the antenna, by a metal bonding, to a ground
wire that runs directly into the earth, via a deep ground rod. For antenna installation guidelines, (see Mounting
the Combination Antenna (VC6096 only) on page 2-10).
WARNING! Keep a minimum lateral distance of 20 cm (8 inches) between the VC6000 Series user and the
antenna. Contact your professional installer, VAR, or antenna manufacturer for proper installation requirements.
6. If installed indoors, connect the WWAN plug of the Combination Antenna cable to the WWAN antenna
connector at the back of the VC6000 Series (VC6096 only). Rotate clockwise to fasten the connector.
7. Connect the WLAN plug of the Combination Antenna cable to the WLAN antenna connector at the back of the
VC6000 Series (VC6096 only). Rotate counterclockwise to fasten the connector.
2 - 14 VC6000 Series Product Reference Guide
12 V DC
Cable
AC Cord
Ground Point
GND
Indoor Power Supply Unit For indoor use only in dry locations
Power Connector
WLAN Antenna Connector
WWAN Antenna Connector
R
Adjustment knob
RAM-246U
8. If installed on an AC-powered Cart,
secure the Indoor Power Supply Unit to
the AC-powered Cart.
Figure 2-8
Desktop Power Supply Connec-
tion

Optional Mounting

The following mounting examples are used for installation demonstration only. For optional mounting instructions, refer to the documentation provided by the mount manufacturer.
WARNING! Vehicles equipped with air bags - An air bag inflates with great force. DO NOT install the
VC6000 Series or place objects, including other communication equipment, in the area over the air bag or in the air bag deployment area. If the communication equipment is improperly installed and the air bag inflates, this could cause serious injury.

Free-standing Pedestal Mount

The Free-standing Pedestal Mount (see Figure 2-9) allows the VC6000 series to be easily readjusted to either the driver or passenger sides in the most comfortable location. A single adjustment knob enables simultaneous adjustment of both upper and lower ball joints. The mount affixes to the VC6000 series using the M4 screws, spring and flat washers and bushings included inside the Hardware kit, and to the vehicle’s dashboard using self tapping screws or bolts, provided by the mount manufacturer.
Figure 2-9
Free-standing Pedestal Mount
Installation 2 - 15
RAM-246U
Adjustment knob
Drill Holes: 4.8 mm ± 0.1 mm
0.256 ± 0.004 in.
100 mm ± 0.1 mm 3.94 ± 0.004 in.
100 mm ± 0.1 mm 3.94 ± 0.004 in.

Desk Mount

The Desk Mount (see Figure 2-10) allows the VC6000 Series to be easily placed on a desk and adjusted to a most comfortable screen view position. A single adjustment knob enables adjustment of both upper and lower ball joints simultaneously. The mount affixes to the VC6000 series using the M4 screws, spring and flat washers and bushings included inside the Hardware Kit.
Figure 2-10
Desk Mount

Mounting Bracket Template for the VC6000 Series

Figure 2-11 shows the drill hole locations for the Mounting Bracket Template of the VC6000 Series.
Figure 2-11
Mounting Bracket Template of the VC6000 Series
2 - 16 VC6000 Series Product Reference Guide
Mounting surface must be flat and stiff and it must extend evenly for the entire length of the mounting bracket surface.
All four mounting holes must be used.
All nuts and bolts must be checked periodically and tightened if required.
When installing the VC6000 Series, care must be taken to ensure that the mounting bracket footprint is fully supported. Additional plates may be required to achieve this.
Installation 2 - 17
R
R
RAM-247U-25 Rail Clamp Base (or alternative)
Drill Holes: 4.8 mm ± 0.1 mm 0.256 ±
0.004 in.
RAM-247U (x4)
Lift Trucks
Use RAM Mount RAM-246U and RAM-247U-25 Rail Clamp Base or alternative to install the VC6090 on the front arm of the electric lift truck.
Secure the VC6090 RAM-246U with four RAM-246U Screws supplied with the VC6090.
Install a RAM Clamp Base to one of the roll cage uprights on the electric lift truck by securing the bolts around one of the uprights using the correct mounting hardware.
NOTE An alternative RAM base may be used may be used to install the VC6090.
Figure 2-12
NOTE Avoid using horizontal mounting with arms longer than RAM-201U to minimize amplification to lift truck vibration.
Horizontal Orientation — Square Upright Mounting Example
Chapter 3 Operating the VC6000 Series

Introduction

This chapter explains the keyboard, buttons, status icons and controls on the VC6000 Series, and provides basic instructions for using the VC6000 Series, including powering on and resetting the VC6000 Series, and entering and capturing data.
3 - 2 VC6000 Series Product Reference Guide
Fn Key Active
Fn Key Lock
Navigation Keys
Function Keys
F1
F5
Back key
(VC6000)
Call key
(VC6096)
Home key (VC6000)
End key
(VC6096)
Soft Keys

Using the Keyboard

For keyboard functionality and description of the keys, refer to Figure 3-1 and Table 3-1.
Figure 3-1
VC6000 Series Keyboard

Keyboard Functionality

Operating the VC6000 Series 3 - 3
Table 3-1
Shift
Caps
Esc
Tab
Ctrl
Alt
Fn
A
through
0
through
VC6000 Series Keyboard Functionality
Key Description
Press the
When typing with Caps Lock on, all letters are CAPITALIZED. The Caps Lock key is toggled of and off by pressing the button.
Press the
Press the
Press the
Press the Ctrl key to activate alternate control functions.
Press the Alt key to activate alternate keyboard functions.
Press the Fn (Function) key1 once to activate alternate functions that are shown on the keyboard in amber text. When the FN key is pressed twice, the Fn Lock icon shows to indicate that the keyboard is locked in the function mode. Press the Fn key again to return to normal keyboard mode.
Z
9
Produces the lowercase alphabetic character shown on the key. Produces uppercase alphabetic character shown on the key when preceded by the Shift key.
Produces the numeric character shown on the key.
Shift
Esc
Tab
Windows key
key followed by a alpha key to create uppercase alphabetic
key to initiate an escape sequence from the function you are using.
key to advance the cursor to the next tab stop.
to open the
Start Menu
Navigation
Function keys
F1
through
Enter
Del / Bksp
Space
Home key (VC6000)
Back key (VC6000)
Call key (VC6096)
End key (VC6096)
Soft keys
F5
Moves the cursor around the screen or highlights the items in a menu. Use the center key for selection.
Programmable function keys. The application determines the use; see the software or application documentation.
Moves the cursor to the next data field or screen.
Deletes the character to the right of the cursor / deletes the character to the left of the cursor.
Enters a space between characters or words.
Press the home key to return to the Today screen.
Press the Back key to go back one screen.
Press the Call key to answer an incoming phone call or to open the Phone program.
Press the End key to end a phone call or return to the Today screen.
Press the Soft keys to perform a function presented by the text shown on the screen next to the key.
3 - 4 VC6000 Series Product Reference Guide
Input Panel icon
Soft Input Panel (SIP)
1
To program the operation of Function keys, refer to Enterprise Mobility Developer Kit (EMDK).
2
To program the operation of Function keys, refer to Enterprise Mobility Developer Kit (EMDK).

Soft Keyboard

The VC6000 Series contains two on-screen Soft Input Panel (SIP) keyboards (see Figure 3-2). The Microsoft SIP looks and functions like a standard keyboard. The VC6000 Series SIP looks and functions like the optional keyboard.
To display the Microsoft SIP keyboard, tap the Input Panel icon in the task tray and select Keyboard from the pop-up menu.
Figure 3-2
Soft Input Panel Keyboard
Starting the Mobile Computer Boot Up
Version 6.1
Open the Start Menu
Notification (VC6096 only)
Connectivity (VC6096 only)
Adjust volume
WAN Status (VC6096 only)
Change the date and time, set up the alarm, and more
Command Bar
Soft Keys
BTExplorer
Wireless Applications
Change the date
and time
Turn on or off radios
Power indicator
The VC6000 Series starts automatically as soon as power is applied; either with a connection to the vehicle power system or when connected to the Indoor Power Supply Unit.
When the mobile computer is powered on for the first time, it initializes its system and the calibration screen is displayed. The Windows Mobile Boot screen (Figure 3-3) appears for a short period of time followed by the window. If the VC6000 Series does not power on, perform a cold boot.
Operating the VC6000 Series 3 - 5
Start Up
Figure 3-3
NOTE The Window Mobile 6.1 screen shots shown in this guide are also relevant to Window Mobile 6.5.

Today Screen

The Today screen (Figure 3-4) displays important information, such as upcoming appointments and status indicators. Tap a section on the screen to open the associated program. Alternatively, tap Start > Today to display the Today screen.
Windows Mobile Boot Screen
Figure 3-4
Toda y Sc r ee n
3 - 6 VC6000 Series Product Reference Guide
To customize the Today screen, tap Start > Settings > Today icon. Use the Appearance tab to customize the background and the Items tab to change the list and order of items that appear on the screen.

Status Icons

The Navigation bar at the top of the screen can contain the status icons listed in Table 3-2.
Table 3-2
Icon Function Description
Status Icons
Notification that one or more instant messages were received.
Notification that one or more e-mail/text messages were received.
Notification that one or more voice messages were received.
There are more notification icons than can be displayed. Tap to display remaining icons.
Indicates a reminder of an upcoming calendar event.
Connection Connection is active.
Connection is not active.
Synchronization is occurring.
Wi-Fi available. (VC6096 only)
Wi-Fi in use. (VC6096 only)
Operating the VC6000 Series 3 - 7
Table 3-2
Icon Function Description
Status Icons (Continued)
WAN (VC6096 only) Call missed.
Dialing while no SIM card is installed.
Voice call in progress.
Calls are forwarded.
Call on hold.
Speakerphone is on.
Antenna/signal icon: wireless on/good signal.
Antenna/signal icon: wireless off.
Antenna/signal icon: no service or searching.
EGPRS connecting.
GPRS connecting.
HSDPA connecting.
GPRS in use.
EGPRS in use.
HSDPA in use.
Roaming.
SIM Card not installed.
Speaker All sounds are on.
All sounds are off.
Time and Next Appointment Displays current time in analog or digital format.
Power is connected.
3 - 8 VC6000 Series Product Reference Guide
The command bar at the bottom of the screen can contain the task tray icons listed in Table 3-3.
Table 3-3
Icon Description
Task Tray Icons
Wi-Fi connection status (VC6096 only)
Bluetooth Enabled Bluetooth radio is on.
Bluetooth Disabled Bluetooth radio is off.
Bluetooth Connection Bluetooth radio is connected to another Bluetooth device.
ActiveSync Active serial connection between the VC6000 Series and the host computer.
Indicates Wi-Fi signal strength.
Wi-Fi radio is off
Wi-Fi radio is on

Programs

Table 3-4 lists the default programs on the Start menu.
Table 3-4
Programs in the Start Menu
Icon Name Description
Calendar Keep track of appointments and create meeting requests.
Contacts Keep track of friends and colleagues.
Phone (VC6096 only) Make and receive calls, switch between calls, and set up conference
calling.
Help See Help topics for the current screen or program.
Operating the VC6000 Series 3 - 9
Table 3-4
Table 3-5 lists programs that are listed in the Programs window.
Table 3-5
Programs in the Start Menu
Icon Name Description
Internet Explorer Mobile Browse Web and WAP sites as well as download new programs and
files from the Internet.
Getting Started Helps setting the VC6000 Series for the first time.
Task Manager Stop running programs or monitor programs performance.
Programs in Program Window
Icon Name Description
ActiveSync Synchronize information between the VC6000 Series and a host
computer or the Exchange Server.
AirBEAM Allows specially designed software packages to be transferred between
a host server and the VC6000 Series.
BTExplorer Manages Bluetooth connections.
Calculator Perform basic arithmetic and calculations, such as addition,
subtraction, multiplication, and division.
File Explorer Organize and manage files on your device.
Internet Sharing Connect a notebook computer to the Internet using the VC6000
Series's data connection.
Ethernet LAN Power Turns on the VC6000 Series Ethernet LAN.
The factory default states for Ethernet LAN power is off.
Device Power Off Turns off the VC6000 Series.
Diagnostic Center Test the VC6000 Series hardware (speaker, screen, memory,
keyboard, battery and more items).
3 - 10 VC6000 Series Product Reference Guide
Table 3-5
Programs in Program Window (Continued)
Icon Name Description
Messenger Use this mobile version of Windows Live Messenger.
MSP Agent Interacts with MSP agents to collect monitoring and asset information
to enable the configuration, provisioning, monitoring and troubleshooting of the VC6000 Series.
Notes Create handwritten or typed notes, drawings, and voice recordings.
Pictures & Videos View and manage pictures, animated GIFs, and video files.
Rapid Deployment Facilitates software downloads from a Mobility Services Platform Console
FTP server to the VC6000 Series.
Remote Desktop Log onto Windows NT server type computers and use all of the programs
that are available on that computer from the VC6000 Series.
Search Search contacts, data, and other information on your VC6000 Series.
SIM Toolkit (VC6096 only)
Manage the contacts that are stored on your SIM card. Copy SIM contents to Contacts on the VC6096.
Tasks Keep track of your tasks.
Windows Live Use this mobile version of Windows Live™ to find information on the
web.
Windows Media Player
Play back audio and video files.
Mobile
Wavelink TE Wavelink TE is the pre-loaded pre-licensed solution for accessing,
managing and maintaining connections to applications resident on host systems using popular emulation types that include 5250, 3270, VT and HP emulation.
To remove Wavelink TE, refer to
Series on page 3-13.
Removing Wavelink TE from the VC6000

Settings

Table 3-6 lists control applications pre installed on the VC6000 Series. Tap Start > Settings to open the Settings
Operating the VC6000 Series 3 - 11
Table 3-6
Personal Tab
Settings in the Setting Window
Icon Name Description
Buttons Assign a program to a button.
Input Set options for each of the input methods.
Lock Set a password for the VC6000 Series.
Menus Set what programs appear in the Start menu.
Owner Information Enter personal information on the VC6000 Series.
Phone (VC6096 only) Make and receive calls, switch between calls, and set up conference
calling.
System Tab
Sounds & Notifications Enable sounds for events, notifications, and more, and set the type of
notification for different events.
Today Customize the appearance and the information to be displayed on the
Today screen.
About
Backlight Set the display backlight time-out and adjust brightness.
Certificates See information about certificates installed on the VC6000 Series.
Clock & Alarms Set the device clock to the date and time of your locale or to a visiting
View basic information such as the Windows Mobile of processor used on the VC6000 Series.
time zone when you’re traveling. Alarms can also be set at specified days and times of a week.
®
version and type
3 - 12 VC6000 Series Product Reference Guide
Table 3-6
Settings in the Setting Window (Continued)
Icon Name Description
Customer Feedback Submit feedback on the Windows Mobile 6 software.
Encryption Allow files on a storage card to be encrypted. Encrypted files are
readable only on your device.
Error Reporting Enable or disable the device's error reporting function. When this
function is enabled and a program error occurs, technical data about the state of the program and your computer is logged in a text file and delivered to Microsoft's technical support if you choose to send it.
External GPS Set the appropriate GPS communication ports, if required. You may
need to do this when there are programs on your device that access GPS data or you have connected a GPS receiver to the VC6000 Series.
GPS Setup View GPS SUPL information.
Keylight Set the keypad backlight time-out.
Memory Check the device memory allocation status and memory card
information and stop currently running programs.
Power Check power and set the time-out for turning off the display to conserve
power.
Regional Settings Set the regional configuration to use, including the format for displaying
numbers, currency, date, and time on the VC6000 Series.
Remove Programs Remove programs that you installed on the VC6000 Series.
To remove Wavelink TE, refer to
Series on page 3-13.
Removing Wavelink TE from the VC6000
Screen Change the screen orientation, re-calibrate the screen, and change the
screen text size.
Task Manager Task Manager shows you the programs, processes, and services that
are currently running on your VC6000 Series. Use Task Manager to monitor your VC6000 Series performance or to close a programs that are not responding.
System Info Displays the VC6000 Series software and hardware information.
Operating the VC6000 Series 3 - 13
Table 3-6
Settings in the Setting Window (Continued)
Icon Name Description
Phone Info Phone radio information.
Windows Update Link to Microsoft's web site and update Windows Mobile® on your
VC6000 Series with the latest security patches or fixes. Do not use. Obtain updates from Zebra.
Connections Tab
Beam Set the to receive incoming IrDA beams (not applicable for the VC6000
Series).
Connections Set up one or more types of modem connections for your device, such
as phone dial-up (VC6096 only), GPRS (VC6096 only), Bluetooth, and more, so that your device can connect to the Internet or a private local network.
USB to PC Enables or disables the enhanced network connectivity.
Wi-Fi VC6096 - setup Wi-Fi network or Ethernet connection and customize
settings. VC6000 - setup Ethernet connection and customize settings.
Wireless Manager Enables or disables the VC6000 Series wireless radios and customizes
Wi-Fi (VC6096 only), Bluetooth and Phone (VC6096 only) settings. The VC6096 Series factory default radio states are: Wi-Fi - OFF. Bluetooth - OFF. Phone - ON.
Domain Enroll Enroll a Windows Mobile device in Microsoft System Center Mobile
Device Manager 2008 using Wi-Fi from wireless access points.

Removing Wavelink TE from the VC6000 Series

To remove Wavelink TE from the \Windows\StartUp folder:
1. Tap the Windows Start button.
2. Scroll down and tap File Explorer.
3. Tap the drop-down list at the top left, and select My device.
4. Tap the Windows > StartUp.
5. Tap and hold on the TelnetCC file until the context menu is opened.
6. Select Delete from the context menu. The device starts to boot-up without automatically trying to run Wavelink TE.
IMPORTANT If clean boot is performed, the Wavelink TE link recovers and needs to be removed again.
3 - 14 VC6000 Series Product Reference Guide
Adjusting Volume
To adjust the system volume using the Speaker icon in the navigation bar:
1. Tap the Speaker icon. The Volume dialog box appears.
Figure 3-5
2. Tap and move the slide bar to adjust the volume.
3. Select the On or Off radio button to turn the volume on or off.
You can also adjust the system volume using the Sounds & Notifications window, or use the Up/Down button on the left hand side of the VC6000 Series front panel.
NOTE volume can also be adjusted by using the volume key of the VC6000 Series.
Volume Dialog Box
Chapter 4 Using the Phone
Antenna Signal

Introduction

Use the VC6096 Series to make phone calls, set up speed dials, keep track of calls, and send text messages. Your wireless service provider may also provide other services such as voice mail, call forwarding, and caller ID.
Also use the integrated phone to connect to an ISP or work network in order to browse the Web and read e-mail. Connect to the Internet or work network over GPRS/EDGE or UMTS/HSDPA using cellular line.

Accessing the Phone Keypad

Access the keypad regardless of the program in use. Applications on the VC6096 can be in use during a call.
Figure 4-1
To access the phone keypad tap Start > Phone or press the green phone key on the VC6096 keypad.
The VC6096 receive calls when the is in Suspend mode, leave the phone radio turned on.
Phone Keypad
4 - 2 MC55 User Guide
Wireless Manager icon
Connectivity icon

Turning the Phone On and Off

Windows Mobile devices include Wireless Manager, which provides a simple method of enabling and disabling the phone.
To open Wireless Manager, tap the Connectivity icon. Wireless Manager can also be opened by taping the line the Wireless Manager icon on the Today screen.
Figure 4-2
Select Wireless Manager. The Wireless Manager window appears.
To toggle on or off the phone, tap blue Phone bar.
To configure settings for a connection, tap Menu > Phone Settings.
Opening Wireless Manager
Audio Modes
Phone Volume Slider
The VC6096 offers three audio modes for use during phone calls:
Speaker Mode: Use the VC6096 as if on speaker phone.
Headset Mode: Connect a Bluetooth headset to automatically switch audio to the headset.

Using a Bluetooth Headset

You can use a Bluetooth headset for audio communication when using an audio-enabled application. See Chapter
6, Using Bluetooth for information on connecting a Bluetooth headset to the VC6096. Set the VC6096’s volume
appropriately before putting the headset on. When a Bluetooth headset is connected the speakerphone is muted.
NOTE Ensure that the Bluetooth headset is set to stay on.
When using a Bluetooth headset, during a call the VC6096 power button is disabled and the VC6096 will not go into suspend mode. Once the call is completed, the power button functionality is enabled.
Using the Phone 4 - 3

Adjusting Audio Volume

Use the Volume Control Slider or the keypad keys to adjust the volume of the ringer when not in a call and the audio volume when in a call.
Figure 4-3
To adjust the volume tap the Speaker icon in the Title bar. Move the slider up or down to adjust the volume.
Phone Volume Slider
NOTE Adjust the conversation phone volume during a call. Adjusting the volume while not in a call affects the ring
and notification sound levels.
4 - 4 MC55 User Guide

Making a Call

NOTE You can make emergency calls even when the VC6096 is locked or when a SIM card is not installed. See
Making an Emergency Call on page 4-6 for more information.
With the VC6096, you can make a call from the phone, contacts, speed dial and call history.

Using the Phone

To make a call using the phone keypad:
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad.
2. From the Phone keypad, tap the number to call.
3. Ta p Talk.
4. Ta p End to stop dialing or end the call.
NOTE Alternatively, use the Send (green) and End Call (red) phone keys on the VC6096 keypad to dial or
disconnect.
If you tap a wrong number, tap Bksp key to erase each subsequent digit of a number. To erase the entire number, tap and hold the Bksp key.

Using Contacts

Use Contacts to make a call without looking up or entering the phone number.
To make a call from Contacts:
1. Ta p Start > Contacts.
2. From the contact list, tap and hold the contact name.
Figure 4-4
3. Ta p Call Work, Call Home or Call Mobile.
Contacts Menu
NOTE To make a call from an open contact, tap the number to call. See On-Device Help for more information about
Contacts.

Using Call History

Phone icon
To make a call using Call History:
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad.
2. From the Phone keypad, tap Call History.
Using the Phone 4 - 5
Figure 4-5
3. Tap the phone icon next to the number to begin dialing and return to the phone keypad.
4. Ta p End or press the red phone key on the VC6096 keypad to stop dialing or end the call.
Call History

Making a Speed Dial Call

Use Speed Dial to call someone saved in the speed dial directory.
To make a speed dial call:
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad.
2. From the Phone keypad, tap and hold the speed dial location number assigned to a contact. (To dial a one-digit
speed dial location number, tap and hold the speed dial number. To dial a two-digit speed dial location number,
tap the first digit and then tap and hold the second digit.)
or
From the Phone keypad, tap Speed Dial and tap the speed dial location number of the desired contact in the
list.
4 - 6 MC55 User Guide
Speed Dial
Location Number
Figure 4-6
3. To stop dialing or end the call, tap End or press the red phone key on the VC6096 keypad.
Speed Dial Contact List

Making an Emergency Call

Your service provider programs one or more emergency phone numbers, such as 911 or 999, that you can call under any circumstances, even when your phone is locked or the SIM card is not inserted. Your service provider can program additional emergency numbers into your SIM card. However, your SIM card must be inserted in your phone in order to use the numbers stored on it. See your service provider for additional information.
NOTE Emergency numbers vary by country. Your phone’s pre-programmed emergency number(s) may not work in
all locations, and sometimes an emergency call cannot be placed due to network, environmental, or interference issues.

Answering a Call

A dialog box appears on the VC6096 when it receives an incoming call. If the phone is set to ring, a ring tone sounds. Answer or ignore the incoming call.
To answer an incoming call tap Answer on the Phone > Incoming... dialog or press the green phone key on the VC6096 keypad.
Figure 4-7
Incoming Call
Using the Phone 4 - 7
To ignore the incoming call tap Ignore. This may send the caller to voice mail, depending on the service provider. Otherwise, this presents Busy to the calling party.
To end the call tap End or press the red phone key on the VC6096 keypad.

Incoming Call Features

If you receive a call while in a call, tap Wait to place the call in call waiting.
You can use other programs on the VC6096 during a call. To switch back to Phone, tap Talk or tap Start > Phone. Tap End to end the call.
If a caller isn't in your contact list, create a contact during the call or from Call History by tapping Menu > Save to Contacts.
To terminate a call when a second call comes in and answer the waiting call, tap End on the Phone keypad to disconnect the active call, then tap Answer or press the Send key to answer the waiting call.
To hold the current call and answer a waiting call, tap Answer or press the Send key to place the current call on hold and answer the incoming call.
To put a call on hold to call another number or answer an incoming call, tap Hold. To move from one call to another, tap Swap.

Smart Dialing

Smart Dialing makes it easy to dial a phone number. When you start entering numbers or characters, Smart Dialing automatically searches and sorts the contact entries on the SIM card, in Contacts, and the phone numbers in Call History (including incoming, outgoing, and missed calls). You can then select the desired number or contact from the filtered list to dial.
Open the Phone screen, then tap the keys on the Phone keypad that correspond to the phone number or contact to call. The contact panel lists contacts that match the sequence that you entered.
Smart Dialing starts looking for numbers or contacts that match the sequence entered.
To find a phone number:
Enter the first one or two digits to find a phone number in Call History.
Enter the first three digits or more to find a phone number from the saved Contacts and SIM card.
To find a contact name:
Enter the first letter of a contact’s first name or last name. Smart Dialing searches for the letter starting from the first character of a contact name as well as from the character that appears after a space, dash, or underscore in a contact name. For example, if you tap number “2” which is associated with [a, b, c] on the Phone keypad, contact names such as the following will be considered matches: “Smith, Bernard”, “Adams, John”, “Carlson, Eileen”, “Dillon, Albert”, “Childs, Larry”, “Cooper, Robert” and “Parks, Celine”.
If the matching list is long narrow down the search further by entering another letter. Using the same example above, tap “3” which is associated with (d, e, f), the matching list is narrowed down to the following names: “Smith, Bernard”, “Adams, John”, and “Parks, Celine”.
4 - 8 MC55 User Guide
Figure 4-8
To make a call or send a text message using Smart Dialing:
1. Begin entering the first few numbers or characters.
2. In the Smart Dialing panel, use the up and down arrows on the keypad to navigate to the desired contact or
phone number.
3. When the correct contact is selected, press TAL K to make a voice call.
4. To send a text message to the selected contact, tap Menu > Send Text Message.
5. To call a different phone number associated with the selected contact, tap the contact name and select the
phone number to call.

Muting a Call

During a call, you can mute the microphone so you can hear the person on the line but he or she cannot hear conversation from the microphone. This is useful when there is conversation or background noise on your end.
To mute or unmute a call:
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad.
2. Make a call.
Finding a Contact
3. Ta p Mute on the display to mute the audio. The Mute icon appears.
Using the Phone 4 - 9
Mute Icon
Note icon
Figure 4-9

Taking Notes

To create a note during a call, tap Note on the display, then enter the note. For more information about creating notes see the Windows On-Device Help.
To access a note created during a call:
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad.
2. From the Phone keypad, tap Call History.
3. Tap and hold the number or the Note icon for the phone call entry containing the note.
Mute Button and Icon
Figure 4-10
4. Ta p View Note.
Call History - Notes Menu
4 - 10 MC55 User Guide
Zebra
Figure 4-11
5. Ta p ok to exit.
Call History - Notes
NOTE Also access notes directly from the Notes application by tapping Start > Notes.

Using Speed Dial

Create speed dial numbers to dial frequently called numbers with a single tap. Before creating a speed dial entry, ensure the phone number exists in Contacts.

Adding a Speed Dial Entry

To add a speed dial entry from the phone keypad:
1. Ensure the contact and phone number are in the Contacts list.
2. Ta p Start > Phone or press the green phone key on the VC6096 keypad.
3. Ta p Start > Speed Dial > Menu > New.
Figure 4-12
4. Tap the desired contact name and number in the list.
Contacts
Using the Phone 4 - 11
Figure 4-13
5. In the Location field, tap the up/down arrows to select an available location to assign as the new speed dial
Speed Dial Contact Location
entry. The first speed dial location is reserved for voice mail.
6. Ta p ok to add the contact to the speed dial list.
Figure 4-14
7. Ta p ok to exit the Speed Dial Contact List.
Speed Dial Contact List
To add a speed dial entry from the Contacts window:
1. Ta p Start > Contacts.
Figure 4-15
Contacts
4 - 12 MC55 User Guide
2. Tap a contact name.
3. Ta p Menu > Add to Speed Dial.
Figure 4-16
4. Tap the up/down arrows to select an available location to assign as the new speed dial entry. The first speed
Speed Dial Contact Location
dial location is reserved for voice mail.
5. Ta p ok.

Editing a Speed Dial Entry

1. Ta p Start > Phone or press the green phone key on the VC6096 keypad.
2. Ta p Menu > Speed Dial.
Figure 4-17
3. Tap and hold the contact name.
4. Ta p Edit... .
5. Change the name, phone number, or location information.
6. Ta p ok.
Speed Dial Contact List
NOTE Editing names and phone numbers in Speed Dial does not alter contact information in Contacts (Start
>
Contacts).

Deleting a Speed Dial Entry

1. Ta p Start > Phone or press the green phone key on the VC6096 keypad.
2. Ta p Menu > Speed Dial.
3. Tap and hold the contact name.
Using the Phone 4 - 13
Figure 4-18
4. Ta p Delete.
5. Ta p Yes to confirm permanently deleting the speed dial entry.
Speed Dial Delete Menu
NOTE Deleting names and phone numbers in Speed Dial does not delete the contact information in Contacts (Start
>

Using Call History

Use Call History to call someone who was recently called, or recently called in. Call History provides the time and duration of all incoming, outgoing, and missed calls. It also provides a summary of total calls and easy access to notes taken during a call. Table 4-1 lists the call history icons that appear in the Call History window.
Table 4-1
Call History Icons
Icon Description
Contacts).
This icon appears next to the contact information for all outgoing calls.
This icon appears next to the contact information for all incoming calls.
This icon appears next to the contact information for all missed calls.

Managing Call History

Change views, reset the call timer, and delete calls to manage the calls stored in Call History.
4 - 14 MC55 User Guide
Changing the Call History View
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad to display the Phone keypad.
2. From the Phone keypad, tap Call History.
3. Ta p Menu > Filter to show the menu.
Figure 4-19
4. Select a view type from the menu to display only missed calls, outgoing calls, incoming calls, or calls listed
Call History - All Calls/Show Menu
alphabetically by caller name.
5. Ta p ok to exit the Call History window.
Resetting the Recent Calls Counter
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad to display the Phone keypad.
2. From the Phone keypad, tap Call History.
3. Ta p Menu.
Figure 4-20
4. Select Call Timers... .
Call History - Tools Menu
Using the Phone 4 - 15
Figure 4-21
5. Ta p Reset. (The All Calls: counter cannot be reset.)
6. Ta p ok to exit the Call Timers window.
Call History - Call Timers
Deleting Call History Items by Call Date
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad to display the Phone keypad.
2. From the Phone keypad, tap Call History.
3. Ta p Menu > Call Timers... .
Figure 4-22
4. In the Delete call history items older than: drop-down list select a time period on which to base deletion of
Call History - Call Timers
stored items.
5. Ta p ok to exit the Call Timers window.
Deleting All Call History Items
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad to display the Phone keypad.
2. From the Phone keypad, tap Call History.
3. Ta p Menu.
4 - 16 MC55 User Guide
Figure 4-23
4. Select Delete all calls.
Figure 4-24
5. Ta p Yes.
6. Ta p ok to exit the Call History window.
Call History - Tools Menu
Call History - Delete All Dialog
Viewing Call Status
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad to display the Phone keypad.
2. From the Phone keypad, tap Call History.
3. Tap an entry. The Call Status window appears.
Figure 4-25
NOTE When more than one call is on the phone line, only the duration of the first call is recorded.
Call History - Detail
Using the Phone 4 - 17
4. Ta p ok and then ok to exit.
Using the Call History Menu
Use the Call History menu to dial voice mail, access the Activation Wizard, save to contacts, view a note, delete a listing, send an SMS, and make a call.
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad to display the Phone keypad.
2. From the Phone keypad, tap Call History.
3. Tap and hold an item in the list.
Figure 4-26
4. Select an applicable item from the menu, as needed.
5. Depending on the item selected, the appropriate window displays. For example, select Send SMS to display
Call History - Menu
the Inbox window.
6. Ta p ok to exit the Call History window.

Swapping Calls

To move between two or more phone calls:
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad to display the Phone keypad.
2. Enter the first phone number and press Tal k . When the call connects, Hold appears on the keypad.
4 - 18 MC55 User Guide
Figure 4-27
3. Ta p Hold on to place the first number on hold.
4. Enter the second number and tap Talk.
Figure 4-28
5. Ta p Swap to move from one call to the other.
6. Ta p End or press the red phone key on the VC6096 keypad to end each call.
Call Swapping - Hold
Call Conferencing - Conferencing

Conference Calling

NOTE Conference Calling and the number of conference calls allowed may not be available on all services. Please
check with your service provider for Conference Calling availability.
To create a conference phone session with multiple people:
1. Ta p Start > Phone or press the green phone key on the VC6096 keypad to display the Phone keypad.
2. Enter the first phone number and press Tal k . When the call connects, Hold appears on the keypad.
Using the Phone 4 - 19
Figure 4-29
3. Ta p Hold to place the first call on hold.
4. Enter the second phone number and tap Talk.
5. After the call is answered, tap Menu > Conference to place the calls in conference mode.
Figure 4-30
6. Ta p Hold to place the conference on hold.
7. Enter another phone number and tap Talk .
Conference Call - Hold
Creating a Conference Call
8. After the call is answered, tap Menu > Conference to place all the calls in conference mode.
9. Repeat steps 6 through 8 for up to six phone numbers.
10. Ta p End or press the red phone key on the VC6096 keypad to end the conference call.
NOTE To speak privately with one party during a conference call, tap Menu > Private. To include all parties again,
tap
Menu > Conference.
4 - 20 MC55 User Guide
Text Message Notification Icon
Figure 4-31
Creating a Private Call

Text Messaging

Use the Text Messages window to send and receive text messages to and from mobile phones. The text can contain words, numbers, or an alphanumeric combination no longer than 160 characters.
Short text messages delivered over mobile networks transmit from the sending VC6096, are stored in a central short message center, then forwarded to the destination mobile device. If the recipient is not available, the message is stored and can be sent later.

Viewing Text Messages

To view a text message:
You can view a text message whether the phone is on or off. When the phone is on, you can view a text message from its notification callout. Tap the text message notification icon on the navigation bar to display the message.
Figure 4-32
The Caller Identification feature matches incoming text message numbers with those stored in Contacts so you know who is sending you a message. Furthermore, the New Text Message dialog box gives you the option to call the sender or save, dismiss, or delete the message.
New Text Message Notification
Using the Phone 4 - 21
Tap Text Messages
Figure 4-33
New Text Message Options
When the phone function is off, you can still view received text message in Messaging:
1. Ta p Start > Messaging > Text Messages, or on the Today screen, tap Text Messages.
Figure 4-34
Text Messaging on Today Screen
The Messaging window appears.
Figure 4-35
2. In the message list, tap a Text Messages.
Messaging Window
4 - 22 MC55 User Guide
Tap to reply the message
Figure 4-36
Text Messages List
NOTE If the phone is turned off and you tried to call the sender, send a reply, or forward the message, you are
prompted to turn the phone function on.

Sending a Text Message

To create a text message:
1. On the Phone screen, select a contact name that you want to send a message to.
2. Ta p Menu > Send Text Message.
Figure 4-37
3. Compose your message.
Phone Screen Contact List
Using the Phone 4 - 23
Address Area
Message Area
Figure 4-38
Create Text Message
The auto-correct feature automatically fixes common spelling errors as you type so your messages are more accurate.
The character counter lets you see and control the size of the message as you compose.
If you want to know if your text message was received, tap Menu > Message Options, then select the Request SMS text message delivery notification check box.
Figure 4-39
4. Ta p Send when you've finished the message.
Message Options Window
If the phone is turned on, your text message is sent. If it’s off, you are prompted to turn on the phone. If you do so, the message is sent; otherwise when you tap ok, the message is saved in the Drafts folder and sent when the phone is turned on.
If you are out of coverage area, the message is saved in the Drafts folder and sent when you return to a coverage area.
NOTE On VC6096, the message remains in the Drafts folder and has to be manually re-sent when you return to a
coverage area.
4 - 24 MC55 User Guide
Chapter 5 Wireless Applications

Introduction

Wireless Local Area Networks (LANs) allow mobile computers to communicate wirelessly and send captured data to a host device in real time. Before using the VC6096 on a WLAN, the facility must be set up with the required hardware to run the wireless LAN and the VC6096 must be configured. Refer to the documentation provided with the access points (APs) for instructions on setting up the hardware.
802.11d is enabled by default. When enabled, the AP must be configured the same in order to connect.
To configure the VC6096, a set of wireless applications provide the tools to configure and test the wireless radio in the VC6096. The
Find WLANs
Manage Profiles
Manage Certs
Manage PACs
Wireless Application menu on the task tray provides the following wireless applications:
Options
Wireless Status
Wireless Diagnostics
Log On/Off
Enable/Disable Radio.
Tap the
To configure the VC6096, a set of wireless applications provide the tools to configure and test the wireless radio in the VC6096. Refer to the Wireless Fusion Enterprise Mobility Suite User Guide for Version X.XX for information on configuring wireless profiles; where X.XX is the Fusion version. Go to http://www.zebra.com/support for the latest version of this guide. See Fusion Software and Hardware Versions on page xiv to determine the Fusion version on the VC6096.

Signal Strength icon to display the Wireless Applications menu.

5 - 2 VC6000 Series Product Reference Guide
Figure 5-1
Wireless Applications Menu

Signal Strength Icon

The Signal Strength icon in the task tray indicates the VC6096’s wireless signal strength as follows:
Table 5-1
Icon Status Action
Signal Strength Icon
Excellent signal strength Wireless LAN network is ready to use.
Very good signal strength Wireless LAN network is ready to use.
Good signal strength Wireless LAN network is ready to use.
Fair signal strength Wireless LAN network is ready to use. Notify the network
Poor signal strength Wireless LAN network is ready to use. Performance may not be
administrator that the signal strength is only “Fair”.
optimum. Notify the network administrator that the signal strength is “Poor”.
Out-of-network range (not associated)
No wireless LAN network card detected
None No wireless LAN network card
detected or Wireless LAN disabled
No wireless LAN network connection. Notify the network administrator.
No wireless LAN network card detected, Wireless LAN disabled or radio disabled. Notify the network administrator.
No wireless LAN network card detected or Wireless LAN disabled or radio disabled. Notify the network administrator.
Turning the WLAN Radio On and Off
To turn the WLAN radio off tap the Signal Strength icon and select Disable Radio.
Wireless Applications 5 - 3
Figure 5-2
To turn the WLAN radio on tap the
Figure 5-3
Disable Radio
Enable Radio
Signal Strength icon and select Enable Radio.
5 - 4 VC6000 Series Product Reference Guide
Chapter 6 Using Bluetooth

Introduction

Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1). Bluetooth wireless technology is specifically designed for short-range (30 feet/10 meters) communication and low power consumption.
VC6000 Series with Bluetooth capabilities can exchange information (e.g., files, appointments, and tasks) with other Bluetooth enabled devices such as phones, printers, access points, and other mobile computers. To use the VC6000 as a modem, create a dial-up modem connection between a computer and the VC6000.
VC6000 Series with Bluetooth technology use the StoneStreet Bluetooth stack. To program Bluetooth within the VC6000, refer to the Software Developer Kit (SDK) documentation.

Adaptive Frequency Hopping

Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used with Bluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work. There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveries during critical 802.11b/g communications. AFH for Bluetooth consists of four main sections:
Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-defined channel mask.
Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network.
Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels.
Channel Maintenance - A method for periodically re-evaluating the channels.
When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b/g high-rate channels. AFH coexistence allows Zebra mobile computers to operate in any infrastructure.
6 - 2 VC6000 Series Product Reference Guide
The Bluetooth radio in this VC6000 Series operates as a Class 2 device power class. The maximum output power is 2.5mW and the expected range is 32.8 feet (10 meters). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether one measures open space or closed office space.
NOTE It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b/g operation is
required.

Security

The current Bluetooth specification defines security at the link level. Application-level security is not specified. This allows application developers to define security mechanisms tailored to their specific need. Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis. The Bluetooth specification defines security algorithms and procedures needed to authenticate devices, and if needed, encrypt the data flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while link encryption is optional.
Pairing of Bluetooth devices is accomplished by creating an initialization key that is used to authenticate the devices and create a link key for them. Entering a common PIN number in the devices being paired generates the initialization key. The PIN number is never sent over the air. By default, the Bluetooth stack responds with no key when a key is requested (it is up to user to respond to the key request event). Authentication of Bluetooth devices is based-upon a challenge-response transaction. Bluetooth allows for a PIN number or passkey that is used to create other 128-bit keys used for security and encryption. The encryption key is derived from the link key used to authenticate the pairing devices. Also worthy of note is the limited range and fast frequency hopping of the Bluetooth radios that makes long-distance eavesdropping difficult.
Recommendations are:
Perform pairing in a secure environment
Keep PIN codes private and don't store the PIN codes in the mobile computer
Implement application-level security.
Turning the Bluetooth Radio Mode On and Off
Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (e.g., an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the VC6000 Series. Turn on the Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with Bluetooth radios in close proximity.

Disabling Bluetooth

To disable Bluetooth, tap Bluetooth icon > Disable Bluetooth. The Bluetooth icon changes to indicate that Bluetooth is disabled.
Using Bluetooth 6 - 3
Figure 6-1
Disable Bluetooth

Enabling Bluetooth

To enable Bluetooth, tap Bluetooth icon > Enable Bluetooth. The Bluetooth icon changes to indicate that Bluetooth is enabled.
Figure 6-2
Enable Bluetooth
6 - 4 VC6000 Series Product Reference Guide

Bluetooth Power States

Cold Boot
Performing a cold or warm boot on the VC6000 Series turns off Bluetooth after initialization (which takes a few moments). It is normal to see the Bluetooth icon appear and disappear, as well as a wait cursor, when initialization proceeds in all modes.
Warm Boot
Performing a warm boot on the VC6000 Series returns Bluetooth to the last state after initialization.
Suspend
Suspending the VC6000 Series turns off Bluetooth.
NOTE When the VC6000 Series is placed in suspend mode, the Bluetooth radio mode powers off and the piconet
(Bluetooth connection) is dropped. When the VC6000 Series resumes, it could take up to 10 seconds for the Bluetooth radio driver to re-initialize the radio.
Resume
When the VC6000 Series resumes, Bluetooth turns on if it was on prior to suspend.

Modes

The BTExplorer application has two modes for managing Bluetooth connections: Wizard Mode and Explorer Mode. The Wizard Mode is for novice Bluetooth users and the Explorer Mode is for experienced Bluetooth users. To switch between modes, select View > Wizard Mode or View > Explorer Mode.

Wizard Mode

Wizard Mode provides a simple process for discovering and connecting to Bluetooth devices.
Wizard Mode shows the devices and services in a simple Favorites view created by following the step-by-step wizard.

Explorer Mode

The Explorer Mode window is easy to navigate and provides greater control to users familiar with Bluetooth. The menu bar provides quick access to the options and tools used to connect to devices. To access Explorer Mode, tap View > Explorer Mode.
NOTE Switching between Wizard Mode and Explorer Mode closes all active connections.
Using Bluetooth 6 - 5
Figure 6-3
You can also use the “tap and hold” technique to view available options. Scroll bars and view options are similar to those on the Windows desktop. The tree structure lists the following sub-items:
Explorer Mode Window
Local Device - This device
Remote Device - Other Bluetooth devices
Trusted Devices - Bonded (paired) Bluetooth devices
Untrusted Devices - Discovered devices that are not bonded
Favorites - Selected services that are set as Favorite for quick access.
NOTE Switching between Wizard Mode and Explorer Mode closes all active connections.
6 - 6 VC6000 Series Product Reference Guide
Discovering Bluetooth Device(s)
The VC6000 Series can receive information from discovered devices without bonding. However, once bonded, the VC6000 Series and a bonded device exchange information automatically when you turn the Bluetooth radio on. See Bonding with Discovered Device(s) on page 6-20 for more information.
To find Bluetooth devices in the area:
1. Ensure that Bluetooth is enabled on both devices.
2. Ensure that the Bluetooth device to discover is in discoverable and connectable modes.
3. Ensure that the require profile is enabled on the VC6000 Series. See Profiles Tab on page 6-31 for more
information.
4. Ensure that the two devices are within 30 feet (10 meters) of one another.
5. Tap the Bluetooth icon and select Show BTExplorer. The BTExplorer window appears.
NOTE If favorite connections have already been created, the Favorites screen displays. If no favorite connections
have been created, the New Connection Wizard screen displays.
6. Ta p Menu > New Connection.The New Connection Wizard appears.
Figure 6-4
7. Select Explore Services on Remote Device or another from the drop-down list and tap Next.
BTExplorer Window
Using Bluetooth 6 - 7
The following actions are available in the drop-down list (actions may vary depending upon configurations):
Explore Services on Remote Device
Pair with a Remote Device
Active Sync via Bluetooth
Browse Files on Remote Device
Connect to Headset
Connect to Internet using Access Point
Connect to Internet using Phone/Modem
Connect to Personal Area Network
Connect to Printer
Send or Exchange Objects
Associate Serial Port.
NOTE If a device discovery action has not been previously performed, a device discovery is automatically initiated. If
a device discovery has previously been performed, the device discovery process is skipped, and the previously found list of devices displays. To start a new device discovery, tap and hold in the window and select
Discover Devices from the pop-up menu.
8. BTExplorer searches for Bluetooth devices in the area.
Figure 6-5
Discover Devices Dialog Box
The discovered devices display in the Select Remote Device window.
6 - 8 VC6000 Series Product Reference Guide
Figure 6-6
9. Select a device from the list and tap Next. The VC6000 Series searches for services on the selected Bluetooth
Select Remote Device Window
device.
Figure 6-7
Device Services
NOTE If the VC6000 Series discovers a service but the service is not supported, the service icon is grayed-out.
10. Select a service from the list and press Next. The Connection Favorite Options window appears.
Using Bluetooth 6 - 9
Figure 6-8
11. In the Favorite Name text box, enter a name for this service that will appear in the Favorite window.
12. Ta p Next. The Connection Summary window appears.
13. Ta p Connect to add the service to the Favorite window and connect to the service.
Figure 6-9
Connection Favorite Options Window
Favorites Window

Available Services

NOTE Some devices might not require a PIN. This depends upon the device’s authentication.
The VC6000 Series offers the following services:
File Transfer Services
Dial-Up Networking Services
OBEX Object Push Services
Headset Audio Gateway Services
6 - 10 VC6000 Series Product Reference Guide
Hands-Free Audio Gateway Services
Serial Port Services
Personal Area Networking Services
IrMC Services.
See the following sections for information on these services.

File Transfer Services

NOTE Shared folders are a security risk.
To transfer files between the VC6000 Series and another Bluetooth enabled device:
1. Ensure the VC6000 Series is discoverable and connectable. See Device Info Tab on page 6-22.
2. Ensure that OBEX File Transfer profile is enabled on the VC6000 Series. See Profiles Tab on page 6-31 for
more information.
NOTE If favorite connections have already been created, the Favorites screen displays. If no favorite connections
have been created, the New Connection Wizard screen displays.
3. Use the Connection Wizard to search for a Bluetooth device.
4. Select the device and tap Next. The Select Remote Service window appears.
5. Ta p Next. The Connection Favorite Options window appears.
6. Ta p Next. The Connection Summary window appears.
7. Ta p Connect. The remote device’s accessible folders appear.
8. Double-tap the file to copy. The Save Remote File window appears.
9. Tap and hold on the file. A pop-up menu appears.
10. Select the action to perform:
New - create a new file or folder on the remote device
Delete - delete the selected file on the remote device.
Get File - copy the file from the remote device to the VC6000 Series.
Put File - copy a file from the VC6000 Series to the remote device.
Creating a New File or Folder
To create a new folder or file on the remote device:
1. Tap and hold on the screen and select New > Folder or New > File. The Create New Folder or Create New
File window appears.
2. Enter the name for the new folder or file.
3. Ta p OK to create the new folder or file on the remote device.
Using Bluetooth 6 - 11
Deleting a File
To delete a file from the remote device:
1. Tap and hold on the file to delete and select Delete.
2. In the Delete Remote Device File dialog box tap Yes.
Getting a File
To copy a file from a remote device:
1. Double-tap or tap and hold on the file and select Get. The Save Remote File window appears.
2. Navigate to the directory to save the file.
3. Ta p Save. The file is transferred from the remote device to the VC6000 Series.
Copying a File
To copy a file to a remote device:
1. Ta p Action > Put. The Send Local File window appears.
2. Navigate to the directory to save the file and select a file.
3. Ta p Open. The file copies from the VC6000 Series to the remote device.

Connecting to the Internet Using an Access Point

This section explains how to access a Bluetooth-enabled LAN access point (AP) for a network connection. Use Internet Explorer to connect to a server.
1. Ensure the VC6000 Series is discoverable and connectable. See Device Info Tab on page 6-22.
2. Ensure that the Personal Area Networking profile is enabled on the VC6000 Series. See Profiles Tab on
page 6-31 for more information.
3. Use the Connection Wizard to search for a Bluetooth AP.
NOTE If favorite connections have already been created, the Favorites screen displays. If no favorite connections
have been created, the New Connection Wizard screen displays.
4. Select the Personal Area Network or Network Access service and select Connect from the pop-up menu.
The VC6000 Series connects with the access point.
5. Ta p Start > Internet Explorer. The Internet Explorer window appears.
6. In the address field, enter an internet address and tap the Enter button. The web page loads.
NOTE Network Access profile is not supported.
6 - 12 VC6000 Series Product Reference Guide

Dial-Up Networking Services

Dial-up networking allows the user to connect a PC or laptop to the VC6000 Series and use the VC6000 Series as a modem to connect to an office network or ISP.
Before setting up dial-up networking, obtain dial-up information and other necessary settings (username, password and domain name, if required) for the office network or ISP. To create a new Bluetooth connection:
1. Ensure the VC6000 Series is discoverable and connectable. See Device Info Tab on page 6-22.
2. Ensure that the Dial-Up Networking profile is enabled on the VC6000 Series. See Profiles Tab on page 6-31
for more information.
3. Ta p Menu > Settings > Services tab.
4. Ta p Add button.
5. Select Dial-up networking Service.
6. Ta p OK. The Edit Local Services window appears.
Figure 6-10
7. In the Local COM Port drop-down list, select DUN1 for GSM configurations or WMP9 for CDMA
Edit Local Service Window
configurations.
8. Ta p OK twice.
9. On the PC or laptop, set up Bluetooth according to the manufacturer’s instructions.
10. On the PC or laptop Bluetooth software, search for the VC6000 Series and select the Dial-up Networking
service.
11. Using dial-up software on the PC or laptop, connect to the VC6000 Series.
12. The VC6000 Series phone function dials the ISP number and connects to the ISP.
13. To verify, on the PC or laptop, launch Internet Explorer and open a web site.

Object Exchange Push Services

Object Exchange (OBEX) is a set of protocols that allows sharing objects such as Contacts or pictures using Bluetooth.
Loading...