TC72 / TC77
Touch Computer
Quick Start Guide
MN-003372-05EN
Copyright
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many
jurisdictions worldwide. All other trademarks are the property of their respective owners.
©2019-2020 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to
www.zebra.com/copyright
TC72/TC77 Quick Start Guide
.
WARRANTY: For complete warranty information, go to www.zebra.com/warranty
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula
Terms of Use
• Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining
the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to
any other parties for any other purpose without the express, written permission of Zebra Technologies.
• Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are
subject to change without notice.
• Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are
correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and
disclaims liability resulting therefrom.
• Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the
accompanying product (including hardware and software) be liable for any damages whatsoever (including,
without limitation, consequential damages including loss of business profits, business interruption, or loss of
business information) arising out of the use of, the results of use of, or inability to use such product, even if
Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
.
.
2
Features
Menu Button
Touch Screen
Scan Button
PTT Button
Back Button
Home Button
Microphone
Charging Contacts
Speaker
Front Facing
Camera (optional)
Data Capture LED
Search Button
Light Sensor
Proximity Sensor
Power Button
Microphone
Receiver
Charging/Notification LED
Interface
Connector
Camera
Elastic Sleeve
Battery Release Latches
Volume Up/Down Button
Battery
Microphone
Camera Flash
Exit Window
Hand Strap Mounting Point
Battery Release Latches
Hand Strap
Scan Button
TC72/TC77 Quick Start Guide
3
TC72/TC77 Quick Start Guide
Removing the SIM Lock Access Cover
NOTE: TC77 with SIM Lock only.
TC77 models with the SIM Lock feature include an access door that is secured using a Microstix 3ULR-0
screw. To remove the access cover, use a Microstix TD-54(3ULR-0) screwdriver to remove the screw from the
access panel.
Figure 1 Remove Secure Access Cover Screw
After re-installing the access cover, make sure to use a Microstix TD-54(3ULR-0) screwdriver to re-install the
screw.
Installing the SIM Card
NOTE: A SIM card is only required on the TC77.
NOTE: Only use a nano SIM card.
CAUTION: For proper electrostatic discharge (ESD) precautions to avoid damaging the SIM card. Proper ESD precautions
include, but not limited to, working on an ESD mat and ensuring that the user is properly grounded.
4
TC72/TC77 Quick Start Guide
nano SIM
Slot 1 (default)
nano SIM
Slot 2
1. Lift the access door.
Figure 2 Remove Access Door
Figure 3 TC77 SIM Slot Locations
2. Slide the SIM card holder to the unlock position.
Figure 4 Unlock SIM Card Holder
5
TC72/TC77 Quick Start Guide
3. Lift the SIM card holder door.
Figure 5 Lift the SIM Card Holder
4. Place the nano SIM card into the card holder with contacts facing down.
Figure 6 Place SIM Card in Holder
5. Close the SIM card holder door and slide to the lock position.
Figure 7 Close and Lock SIM Card Holder Door
6
6. Replace the access door.
Mini SAM Slot
Figure 8 Replace Access Door
7. Press the access door down and ensure that it is properly seated.
CAUTION: Access door must be replaced and securely seated to ensure proper device sealing.
Installing the SAM Card
CAUTION: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the Secure Access Module (SAM)
card. Proper ESD precautions include, but not limited to, working on an ESD mat and ensuring that the user is properly
grounded.
TC72/TC77 Quick Start Guide
NOTE: If using a micro SAM card, a third-party adapter is required.
1. Lift the access door.
Figure 9 Remove Access Door
2. Insert a SAM card into the SAM slot with the cut edge toward the middle of the device and the contacts
facing down.
Figure 10 SAM Card Installation
3. Ensure that the SAM card is seated properly.
7
Loading...