Zebra TC70x, TC75x User Guide

TC70x/TC75x
Touch Computer
User Guide
for Android ™ 8.1 Oreo
MN-003376-03

Copyright

ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. Google, Android, Google Play and other marks are trademarks of Google LLC; Oreo is a trademark of Mondelez International, Inc. group. All other trademarks are the property of their respective owners. ©2019 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to www.zebra.com/
copyright.
WARRANTY: For complete warranty information, go to www.zebra.com/warranty
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula

Terms of Use

Proprietary Statement

This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries (“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies.

Product Improvements

Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice.

Liability Disclaimer

Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.
.
.

Limitation of Liability

In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
2

Revision History

Changes to the original guide are listed below:
Change Date Description
-01 Rev A 8/2018 Initial release.
-02 Rev A 10/2018 Add WWAN information.
-03 Rev A 7/2019 Add note warning against user modification of the device, particularly in the battery well.
3

Table of Contents

Copyright ......................................................................................................................... 2
Terms of Use ..................................................................................................................2
Proprietary Statement ............................................................................................. 2
Product Improvements ............................................................................................ 2
Liability Disclaimer ................................................................................................... 2
Limitation of Liability ................................................................................................ 2
Revision History ..............................................................................................................3
About This Guide........................................................................................................ 14
Introduction ................................................................................................................... 14
Documentation Set ....................................................................................................... 14
Configurations ............................................................................................................... 14
Software Versions ......................................................................................................... 15
Chapter Descriptions .................................................................................................... 15
Notational Conventions ................................................................................................. 16
Related Documents ...................................................................................................... 16
Service Information ....................................................................................................... 16
Provide Documentation Feedback ................................................................................ 17
Getting Started............................................................................................................ 18
Introduction ................................................................................................................... 18
Unpacking .....................................................................................................................18
Features ........................................................................................................................ 19
Setup ............................................................................................................................. 21
Installing the SIM Card .......................................................................................... 22
Installing a microSD Card ...................................................................................... 23
Installing the Hand Strap and Battery .................................................................... 24
Installing the Battery .............................................................................................. 26
Charging the Battery ............................................................................................. 26
Charging Indicators ............................................................................................... 27
4
Table of Contents
Google Account Setup .......................................................................................... 27
Zebra Visibility Services ................................................................................................ 27
Replacing the Battery .................................................................................................... 28
Replacing the SIM Card ................................................................................................ 30
Replacing the microSD Card ........................................................................................ 32
Accessing Device Settings ............................................................................................ 33
Battery Management ..................................................................................................... 33
Monitoring Battery Usage ...................................................................................... 34
Low Battery Notification ......................................................................................... 34
Battery Optimization ...................................................................................................... 35
Turning Off the Radios .......................................................................................... 35
Setting the Date and Time ............................................................................................ 35
Display Settings ............................................................................................................ 36
Setting the Screen Brightness ............................................................................... 36
Setting Screen Timeout ......................................................................................... 36
Ambient Display .................................................................................................... 37
Setting Touch Key Light ........................................................................................ 37
Setting Font Size ................................................................................................... 38
Setting Screen Rotation ........................................................................................ 39
Touch Panel Mode ................................................................................................ 39
Setting Display Size .............................................................................................. 40
General Sound Setting .................................................................................................. 41
Wake-Up Sources ......................................................................................................... 42
Using the Device ......................................................................................................... 44
Introduction ................................................................................................................... 44
Google Mobile Services ................................................................................................ 44
Home Screen ................................................................................................................ 44
Setting Home Screen Rotation .............................................................................. 46
Status Bar .............................................................................................................. 46
Status Icons .................................................................................................... 47
Notification Icons ............................................................................................. 48
Managing Notifications .......................................................................................... 49
Setting App Notifications ................................................................................. 50
Viewing Notification Settings for All Apps ....................................................... 50
Controlling Lock Screen Notifications ............................................................. 50
Blink Light ....................................................................................................... 50
Quick Access Panel .............................................................................................. 51
Editing Icons on Quick Settings ...................................................................... 52
App Shortcuts and Widgets ................................................................................... 53
Adding an App Shortcut to the Home Screen ................................................. 53
Adding a Widget to the Home Screen ............................................................. 53
5
Table of Contents
Moving Items on the Home Screen ................................................................. 53
Removing an App Shortcut or Widget from the Home Screen ....................... 53
Folders .......................................................................................................................... 54
Creating a Folder ............................................................................................ 54
Naming Folders ............................................................................................... 54
Removing a Folder .......................................................................................... 54
Home Screen Wallpaper ....................................................................................... 54
Using the Touchscreen ................................................................................................. 55
Keyboards .....................................................................................................................55
Keyboard Configuration ......................................................................................... 55
Enabling Keyboards ........................................................................................ 55
Switching Between Keyboards ....................................................................... 56
Using the Android and Gboard Keyboards ............................................................ 56
Editing Text ..................................................................................................... 56
Entering Numbers, Symbols, and Special Characters .................................... 56
Using the Enterprise Keyboard ............................................................................. 56
Numeric Tab ................................................................................................... 57
Alpha Tab ........................................................................................................ 57
Additional Character Tab ................................................................................ 57
Scan Tab ......................................................................................................... 58
Do Not Disturb Feature ................................................................................................. 58
Limit Sounds and Vibrations .................................................................................. 58
Total Silence ................................................................................................... 58
Alarms Only .................................................................................................... 59
Priority Notifications Only ................................................................................ 59
Automatically Block Sounds and Vibrations .......................................................... 60
Silence Sounds During Certain Times ............................................................ 60
Silence Sounds During Events and Meetings ................................................. 60
Turn Sounds Back On ........................................................................................... 61
Override Do Not Disturb for Specific Apps ............................................................ 61
Apps .............................................................................................................................. 61
Accessing Apps ............................................................................................................ 64
Switching Between Recent Apps .......................................................................... 65
Un-Locking the Screen ................................................................................................. 66
Interactive Sensor Technology ..................................................................................... 68
Resetting the Device ..................................................................................................... 69
Performing a Soft Reset ........................................................................................ 69
Performing a Hard Reset ....................................................................................... 69
Suspend Mode .............................................................................................................. 69
Transferring Files with a Host Computer via USB ........................................................ 70
Transferring Files .................................................................................................. 70
Transferring Photos ............................................................................................... 70
Disconnect from the Host Computer ..................................................................... 71
6
Table of Contents
Applications ................................................................................................................ 72
Introduction ................................................................................................................... 72
Battery Manager ........................................................................................................... 72
Camera ........................................................................................................................ 75
Taking Photos ....................................................................................................... 75
Taking a Panoramic Photo .................................................................................... 76
Recording Videos .................................................................................................. 77
Photo Settings ....................................................................................................... 78
Rear Camera .................................................................................................. 78
Front Camera .................................................................................................. 78
Video Settings ....................................................................................................... 79
Rear Camera .................................................................................................. 79
Front Camera .................................................................................................. 79
Contacts ....................................................................................................................... 80
Adding a Contact ................................................................................................... 80
Editing Contacts .................................................................................................... 80
Deleting Contacts .................................................................................................. 80
DataWedge Demonstration .......................................................................................... 81
Scanner Selection ................................................................................................. 82
Device Central .............................................................................................................. 82
Device Central Tabs .............................................................................................. 82
Paging an RS6000 Ring Scanner ......................................................................... 83
Diagnostic Tool ............................................................................................................ 85
Settings ................................................................................................................. 88
Battery Test Information ........................................................................................ 88
GPS Test Information ............................................................................................ 89
System Test Information ....................................................................................... 89
WLAN Test Information ......................................................................................... 89
WWAN Test Information ........................................................................................ 89
Bluetooth Test Information .................................................................................... 90
Files ............................................................................................................................. 91
Gallery .......................................................................................................................... 92
Working with Albums ............................................................................................. 94
Sharing an Album ........................................................................................... 94
Getting Album Information .............................................................................. 94
Deleting an Album ........................................................................................... 95
Working with Photos .............................................................................................. 95
Viewing and Browsing Photos ........................................................................ 95
Cropping a Photo ............................................................................................ 96
Setting a Photo as a Contact Icon .................................................................. 96
Sharing a Photo .............................................................................................. 97
Deleting a Photo ............................................................................................. 97
Working with Videos .............................................................................................. 97
7
Table of Contents
Watching Videos ............................................................................................. 97
Sharing a Video .............................................................................................. 97
Deleting a Video .............................................................................................. 98
Messaging .................................................................................................................... 99
Sending a Text Message ....................................................................................... 99
Sending a Multimedia Message ............................................................................ 99
Photos ........................................................................................................................ 101
Working with Photos ............................................................................................ 102
Viewing and Browsing Photos ...................................................................... 102
Cropping a Photo .......................................................................................... 103
Setting a Photo as a Contact Icon ................................................................ 104
Sharing a Photo ............................................................................................ 104
Deleting a Photo ........................................................................................... 105
Working with Albums ........................................................................................... 105
Sharing an Album ......................................................................................... 105
Deleting an Album ......................................................................................... 106
Working with Videos ............................................................................................ 106
Watching a Video .......................................................................................... 106
Sharing a Video ............................................................................................ 106
Deleting a Video ............................................................................................ 106
PTT Express Voice Client .......................................................................................... 107
PTT Express User Interface ................................................................................ 107
PTT Audible Indicators ........................................................................................ 108
PTT Notification Icons ......................................................................................... 108
Enabling PTT Communication ............................................................................. 108
Selecting a Talk Group ........................................................................................ 109
PTT Communication ............................................................................................ 109
Creating a Group Call ................................................................................... 109
Responding with a Private Response ........................................................... 109
Disabling PTT Communication ............................................................................ 110
RxLogger ................................................................................................................... 111
RxLogger Utility .......................................................................................................... 112
SimulScan Demo ....................................................................................................... 113
Printing the Sample Forms .................................................................................. 113
Using the Postal, Transportation and Logistics Example .................................... 114
Using the Manufacturing Example ...................................................................... 116
Settings ............................................................................................................... 117
Advanced Settings .............................................................................................. 118
Creating a Demo Customization ......................................................................... 119
Default Templates ......................................................................................... 120
Sound Recorder ......................................................................................................... 121
Data Capture.............................................................................................................. 122
8
Table of Contents
Introduction ................................................................................................................. 122
Imaging .......................................................................................................................122
Operational Modes .............................................................................................. 122
RS507/RS507X Hands-Free Imager .......................................................................... 123
............................................................................................................................ 123
RS6000 Bluetooth Ring Scanner ................................................................................ 123
DS3678 Digital Scanner .............................................................................................. 124
Scanning Considerations ............................................................................................ 124
Scanning with Internal Imager .................................................................................... 124
Scanning with RS507/RS507X Hands-Free Imager ................................................... 126
Scanning with RS6000 Bluetooth Ring Scanner ......................................................... 127
Scanning with the DS3608 USB Scanner or DS3678 Bluetooth Scanner .................. 129
Pairing the RS507/RS507X/RS6000 Hands-Free Imager .......................................... 130
Pairing Using Near Field Communication ........................................................... 130
Pairing in HID Mode Using Near Field Communication ...................................... 130
Pairing Using Simple Serial Interface (SSI) ......................................................... 131
Pairing Using Bluetooth Human Interface Device ............................................... 132
Pairing a Bluetooth Scanner ....................................................................................... 133
Pairing Using Bluetooth Human Interface Device ............................................... 133
DataWedge ................................................................................................................ 135
Enabling DataWedge .......................................................................................... 135
Disabling DataWedge .......................................................................................... 135
Calls ........................................................................................................................... 136
Introduction ................................................................................................................. 136
Emergency Calling ...................................................................................................... 136
Audio Modes ............................................................................................................... 136
Using a Bluetooth Headset ......................................................................................... 136
Using a Wired Headset ............................................................................................... 136
Adjusting Audio Volume .............................................................................................. 137
Making a Call Using the Dialer .................................................................................... 137
Dialer Dialing Options .......................................................................................... 139
Making a Call Using Contacts ..................................................................................... 139
Using the Dialer ................................................................................................... 139
Using the Contacts App ....................................................................................... 140
Making a Call Using Call History ................................................................................. 142
Making a Conference Call ........................................................................................... 142
Making a Call Using a Bluetooth Headset .................................................................. 145
Answering Calls .......................................................................................................... 145
Call Settings ................................................................................................................ 146
9
Table of Contents
Wireless ..................................................................................................................... 148
Introduction ................................................................................................................. 148
Wireless Wide Area Networks .................................................................................... 148
Sharing the Mobile Data Connection ................................................................... 148
Enabling USB Tethering ............................................................................... 148
Enabling Bluetooth Tethering ........................................................................ 149
Enabling Wi-Fi Hotspot ................................................................................. 149
Configuring the Wi-Fi Hotspot ....................................................................... 149
Cellular Network Settings .................................................................................... 150
Disabling Data When Roaming ..................................................................... 150
Preferred Network Type ................................................................................ 150
Enhanced 4G LTE Mode .............................................................................. 150
Using Search for MicroCell ........................................................................... 151
Using System Select ..................................................................................... 151
Configuring the Access Point Name .................................................................... 151
Locking the SIM Card .......................................................................................... 151
Data Usage ......................................................................................................... 152
Setting Data Usage Warning ........................................................................ 152
Setting Data Limit .......................................................................................... 152
Wireless Local Area Networks .................................................................................... 153
Connecting to a Wi-Fi Network ............................................................................ 153
Removing a Wi-Fi Network .................................................................................. 155
Bluetooth .....................................................................................................................155
Adaptive Frequency Hopping .............................................................................. 155
Security ............................................................................................................... 156
Bluetooth Profiles ................................................................................................ 156
Bluetooth Power States ....................................................................................... 157
Bluetooth Radio Power ........................................................................................ 157
Enabling Bluetooth ........................................................................................ 157
Disabling Bluetooth ....................................................................................... 157
Discovering Bluetooth Device(s) ......................................................................... 158
Changing the Bluetooth Name ............................................................................ 158
Connecting to a Bluetooth Device ....................................................................... 158
Selecting Profiles on the Bluetooth Device ......................................................... 158
Unpairing a Bluetooth Device .............................................................................. 159
Near Field Communications ........................................................................................ 159
Reading NFC Cards ............................................................................................ 159
Sharing Information Using NFC .......................................................................... 160
Cast ............................................................................................................................. 161
Accessories............................................................................................................... 162
Introduction ................................................................................................................. 162
10
Table of Contents
Accessories ................................................................................................................. 162
2-Slot Charge Only Cradle .......................................................................................... 165
Charging the Device ............................................................................................ 166
Charging the Spare Battery ................................................................................. 167
Battery Charging ................................................................................................. 167
Main Battery Charging .................................................................................. 167
Spare Battery Charging ................................................................................ 167
Charging Temperature .................................................................................. 168
2-Slot USB/Ethernet Cradle ........................................................................................ 168
Charging the Device ............................................................................................ 170
Charging the Spare Battery ................................................................................. 171
Battery Charging ................................................................................................. 171
Main Battery Charging .................................................................................. 171
Spare Battery Charging ................................................................................ 171
Charging Temperature .................................................................................. 172
USB/Ethernet Communication ............................................................................ 172
Ethernet LED Indicators ................................................................................ 173
Establishing Ethernet Connection ....................................................................... 173
5-Slot Charge Only Cradle .......................................................................................... 173
Charging the TC75 .............................................................................................. 175
Battery Charging ................................................................................................. 175
Main Battery Charging .................................................................................. 175
Spare Battery Charging ................................................................................ 175
Charging Temperature .................................................................................. 176
4-Slot Charge Only Cradle with Battery Charger ........................................................ 176
Charging the Device ............................................................................................ 178
Battery Charging ................................................................................................. 178
Main Battery Charging .................................................................................. 178
Spare Battery Charging ................................................................................ 178
Charging Temperature .................................................................................. 179
5-Slot Ethernet Cradle ................................................................................................ 179
Charging the Device ............................................................................................ 181
Battery Charging ................................................................................................. 182
Main Battery Charging .................................................................................. 182
Spare Battery Charging ................................................................................ 182
Charging Temperature .................................................................................. 183
Establishing Ethernet Connection ....................................................................... 183
LED Indicators ..................................................................................................... 183
4-Slot Battery Charger ............................................................................................... 184
Charging Spare Batteries .................................................................................... 184
Battery Charging ................................................................................................. 184
Spare Battery Charging ................................................................................ 184
Charging Temperature .................................................................................. 185
3.5 mm Audio Adapter ................................................................................................ 185
11
Table of Contents
Connecting a Headset to the 3.5 mm Audio Adapter .......................................... 186
Attaching the 3.5 mm Audio Adapter ................................................................... 187
Device with 3.5 mm Audio Adapter in Holster ..................................................... 187
Removing the 3.5 mm Audio Adapter ................................................................. 188
Snap-On USB Cable ................................................................................................... 188
Connecting to Device .......................................................................................... 188
USB Communication ........................................................................................... 189
Charging the Device ............................................................................................ 189
Disconnecting from Device .................................................................................. 190
Battery Charging ................................................................................................. 191
Main Battery Charging .................................................................................. 191
Charging Temperature .................................................................................. 191
Charging Cable Cup ................................................................................................... 191
Charging the Device ............................................................................................ 192
Battery Charging ................................................................................................. 193
Main Battery Charging .................................................................................. 193
Charging Temperature .................................................................................. 193
Snap-On DEX Cable ................................................................................................... 193
Connecting to Device .......................................................................................... 194
DEX Communication ........................................................................................... 194
Disconnecting from Device .................................................................................. 195
Trigger Handle ............................................................................................................ 196
Installing the Attachment Plate to Trigger Handle ............................................... 196
Installing the Trigger Handle Plate ...................................................................... 196
Inserting the Device into the Trigger Handle ....................................................... 198
Removing the Device from the Trigger Handle ................................................... 200
Vehicle Charging Cable Cup ....................................................................................... 202
Charging the Device ............................................................................................ 203
Battery Charging ................................................................................................. 204
Main Battery Charging .................................................................................. 204
Charging Temperature .................................................................................. 204
Vehicle Cradle ............................................................................................................. 204
Device Insertion and Removal ............................................................................ 206
Battery Charging ................................................................................................. 207
TC7X Vehicle Communication Charging Cradle ......................................................... 207
Device Insertion and Removal ............................................................................ 209
Device Battery Charging ..................................................................................... 209
Charging Note ............................................................................................... 209
USB I/O Hub ............................................................................................................... 210
Connect USB Cables .......................................................................................... 210
External USB Cable ............................................................................................ 211
Power to Vehicle Cradle ...................................................................................... 212
12
Table of Contents
Audio Headset Connection .................................................................................. 212
Maintenance and Troubleshooting ......................................................................... 214
Introduction ................................................................................................................. 214
Maintaining the Device ................................................................................................ 214
Battery Safety Guidelines ........................................................................................... 214
Cleaning Instructions .................................................................................................. 215
Approved Cleanser Active Ingredients ................................................................ 215
Harmful Ingredients ............................................................................................. 215
Device Cleaning Instructions ............................................................................... 216
Special Cleaning Notes ....................................................................................... 216
Cleaning Materials Required ............................................................................... 216
Cleaning Frequency ............................................................................................ 216
Cleaning the Device ............................................................................................ 217
Housing ......................................................................................................... 217
Display .......................................................................................................... 217
Camera and Exit Window ............................................................................. 217
Cleaning Battery Connectors .............................................................................. 217
Cleaning Cradle Connectors ............................................................................... 217
Troubleshooting .......................................................................................................... 218
Technical Specifications.......................................................................................... 221
Introduction ................................................................................................................. 221
13

About This Guide

Introduction

This guide provides information about using the device and accessories.
NOTE: Screens and windows pictured in this guide are samples and can differ from actual screens.

Documentation Set

The documentation set for the device provides information for specific user needs, and includes:
TC70x/TC75x Touch Computer Quick Start Guide for Android Version 6.0.1 - Describes how to get the device up and running.
TC70x/TC75x Touch Computer User Guide for Android Version 8.1 - Describes how to use the device.
TC70x/TC75x Touch Computer Integrator Guide for Android Version 8.1 - Describes how to set up the device and accessories.

Configurations

This guide covers the following configurations:
Configuration Radios Display Memory
TC700K WLAN: 802.11
TC75EK WWAN:
a/b/g/n/d/h/i/r
WPAN: Bluetooth v4.0 Low Energy
HSPA+/LTE/C DMA
WLAN: 802.11 a/b/g/n/d/h/i/r
WPAN: Bluetooth v4.0 Low Energy
4.7” High Definition (1280 x 720) LCD
4.7” High Definition (1280 x 720) LCD
4 GB RAM/32 GB Flash
4 GB RAM/32 GB Flash
Data Capture
Options
2D imager, camera, or integrated NFC
2D imager, camera and integrated NFC
Operating
System
Android 8.1
Android 8.1
14
About This Guide
Configuration Radios Display Memory
TC75FK WWAN:
TC75GK WWAN:

Software Versions

To determine the current software versions:
1. Swipe down from the Status bar to open the Quick Settings bar.
HSPA+/LTE
WLAN: 802.11 a/b/g/n/d/h/i/r
WPAN: Bluetooth v4.0 Low Energy
HSPA+/LTE
WLAN: 802.11 a/b/g/n/d/h/i/r
WPAN: Bluetooth v4.0 Low Energy
4.7” High Definition (1280 x 720) LCD
4.7” High Definition (1280 x 720) LCD
4 GB RAM/32 GB Flash
4 GB RAM/32 GB Flash
Data Capture
Options
2D imager, camera and integrated NFC
2D imager, camera and integrated NFC
Operating
System
Android 8.1
Android 8.1
2. Touch > System.
3. Touch About phone.
4. Scroll to view the following information:
•Model
Android version
•Kernel version
Build number.
To determine the device serial number, touch About phone > Status.
Serial number

Chapter Descriptions

Topics covered in this guide are as follows:
Getting Started provides information on getting the device up and running for the first time.
Using the Device provides information for operating the device.
Calls provides instructions for making phone calls.
Applications provides information on using applications installed on the device.
Data Capture provides information for capturing barcode data using the imager.
Wireless provides information on the various wireless options.
Accessories provides information for using the accessories for the device.
Maintenance and Troubleshooting includes instructions on cleaning and provides troubleshooting solutions for potential problems during device operation.
15
Technical Specifications provides the technical specifications for the device.

Notational Conventions

The following conventions are used in this document:
Bold text is used to highlight the following:
Dialog box, window and screen names
Drop-down list and list box names
Check box and radio button names
Icons on a screen
Key names on a keypad
Button names on a screen.
Bullets (•) indicate:
Action items
Lists of alternatives
Lists of required steps that are not necessarily sequential.
Sequential lists (for example, those that describe step-by-step procedures) appear as numbered lists.
About This Guide

Related Documents

TC70x/TC75x Touch Computer Quick Start Guide for Android Version 6.0.1, p/n MN-002879-xx.
TC75x Touch Computer Regulatory Guide for Android Version 6.0.1, p/n MN-002880-xx.
TC70x Touch Computer Regulatory Guide for Android Version 6.0.1, p/n MN-002960-xx.
TC70x/TC75x Touch Computer Integrator Guide for Android Version 8.1, p/n MN-003375-xx.
RS507 Hands-free Imager Product Reference Guide, p/n 72E-12082-xx.
DS36X8 Product Reference Guide, p/n MN-002689-xx.
RS6000 User Guide, MN-002704-xx.
For the latest version of this guide and all guides, go to: www.zebra.com/support

Service Information

If you have a problem with your equipment, contact Customer Support for your region. Contact information is available at: www.zebra.com/support
When contacting support, please have the following information available:
Serial number of the unit (found on manufacturing label)
Model number or product name (found on manufacturing label)
Software type and version number
IMEI number.
.
.
Customer Support responds to calls by email or telephone within the time limits set forth in support agreements.
If the problem cannot be solved by Customer Support, you may need to return the equipment for servicing and will be given specific directions. We are not responsible for any damages incurred during shipment if the
16
About This Guide
approved shipping container is not used. Shipping the units improperly can possibly void the warranty. Remove the SIM card and/or microSD card from the device before shipping for service.
If the device was purchased from a business partner, contact that business partner for support.

Provide Documentation Feedback

If you have comments, questions, or suggestions about this guide, send an email to
EVM-Techdocs@zebra.com
.
17

Getting Started

Introduction

This chapter provides information for getting the device up and running for the first time.

Unpacking

1. Carefully remove all protective material from the device and save the shipping container for later storage and shipping.
2. Verify that the following were received:
Touch computer
4,620 mAh PowerPercision+ Lithium-ion battery
Hand strap
Regulatory Guide.
3. Inspect the equipment for damage. If any equipment is missing or damaged, contact the Global Customer Support center immediately.
4. Prior to using the device for the first time, remove the protective shipping film that covers the scan window, display and camera window.
18

Features

2
3
4
5
6
7
8
18
17
9
10
11
12
13
14
15
16
1
Figure 1 Front View
Getting Started
Table 1 Front View Features
Number Item Function
1 Touch Screen Displays all information needed to operate the device.
2 Scan Button Initiates data capture (programmable).
3 PTT Button Initiates push-to-talk communications (programmable).
4 Back Button Displays the previous screen.
5 Home Button Displays the Home screen with a single press.
On device with GMS, opens the Google Now screen when held for a short period of time.
6 Microphone Use for communications in Handset mode.
7 Charging
Provides power to the device from cables and cradles.
Contacts
8 Speaker Provides audio output for video and music playback. Provides audio in
speakerphone mode.
9 Search Button Opens the Recent App screen.
10 Menu Button Opens a menu with items that affect the current screen or application.
11 Light Sensor Determines ambient light for controlling display backlight intensity.
12 Proximity Sensor Determines proximity for turning off display when in handset mode.
19
Getting Started
Table 1 Front View Features (Continued)
Number Item Function
13 Power Button Turns the display on and off. Press and hold to reset the device, power off or
swap battery.
14 Microphone Use for communications in Speakerphone mode.
15 Receiver Use for audio playback in Handset mode.
16 Charging/Notifica
tion LED
17 Data Capture
LED
18 Front Facing
Camera
Indicates battery charging status while charging and application generated notifications.
Indicates data capture status.
Use to take photos and videos (optional).
20
Figure 2 Rear View
19
24
23
22
25
21
20
28
29
27
23
26
Table 2 Back View Features
Getting Started

Setup

Number Item Function
19 Interface
Connector
Provides USB host and client communications, audio and device charging via cables and accessories.
20 Exit Window Provides data capture using the imager.
21 Microphone Use during video recording and for noise cancellation.
22 Volume
Increase and decrease audio volume (programmable).
Up/Down Button
23 Battery Release
Press to remove the battery.
Latches
24 Elastic Sleeve Use to hold optional stylus.
25 Battery Provides power to the device.
26 Hand strap Use to securely hold the device in your hand.
27 Hand strap
Provides latching point for the hand strap.
Mounting Point
28 Camera Takes photos and videos.
29 Camera Flash Provides illumination for the camera.
Perform this procedure to start using the device for the first time.
1. Install a SIM card (TC75x only).
2. Install a micro secure digital (SD) card (optional).
3. Install hand strap (optional).
4. Install the battery.
21
5. Charge the device.
mini SIM Slot
nano SIM Slot
1 (default)
nano SIM
Slot 2
6. Power on the device.

Installing the SIM Card

NOTE: TC75x only.
NOTE: The TC75x may contain one mini SIM slot and two nano SIM slots. If using a micro SIM card, a third-party SIM adapt-
er is required. By default, use a nano SIM card in slot 1.
CAUTION: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the SIM card. Proper ESD precau-
tions include, but not limited to, working on an ESD mat and ensuring that the user is properly grounded.
1. Remove access cover.
Figure 3 TC75x SIM Slot Locations
Getting Started
22
Getting Started
2. Insert a SIM card into the SIM slot with the cut edge toward the middle of the device and the contacts facing down.
Figure 4 nano SIM Card Installation
Figure 5 Mini SIM Card Installation
3. Ensure that the SIM card is seated properly.

Installing a microSD Card

The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack. Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.
CAUTION: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper ESD pre-
cautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
1. Remove the hand strap, if installed.
2. Lift the access door.
Figure 6 Lift Access Door
23
Getting Started
3. Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door.
Figure 7 Insert microSD Card in Holder
4. Re-install the access door.

Installing the Hand Strap and Battery

NOTE: User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc.,
may compromise the intended performance of the device or accessories. Performance levels such as sealing (Ingress Pro­tection (IP)), impact performance (drop and tumble), functionality, temperature resistance, etc. could be effected. DO NOT put any labels, asset tags, engravings, stickers, etc. in the battery well.
NOTE: Installation of the hand strap is optional. Skip this section if not installing the hand strap.
1. Remove the hand strap filler from the hand strap slot. Store the hand strap filler in a safe place for future replacement.
Figure 8 Remove Filler
24
Getting Started
2. Insert the hand strap plate into the hand strap slot.
Figure 9 Insert Hand Strap
3. Insert the battery, bottom first, into the battery compartment in the back of the device.
Figure 10 Insert Bottom of Battery into Battery Compartment
4. Press the battery down into the battery compartment until the battery release latches snap into place.
Figure 11 Press Down on Battery
25
5. Place hand strap clip into hand strap mounting slot and pull down until it snaps into place.
Figure 12 Secure Hand Strap Clip

Installing the Battery

NOTE: User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc.,
may compromise the intended performance of the device or accessories. Performance levels such as sealing (Ingress Pro­tection (IP)), impact performance (drop and tumble), functionality, temperature resistance, etc. could be effected. DO NOT put any labels, asset tags, engravings, stickers, etc. in the battery well.
1. Insert the battery, bottom first, into the battery compartment in the back of the device.
Getting Started
Figure 13 Insert Bottom of Battery into Battery Compartment
2. Press the battery down into the battery compartment until the battery release latches snap into place.
Figure 14 Press Down on Battery

Charging the Battery

Before using the device for the first time, charge the main battery until the green Charging/Notification light emitting diode (LED) remains lit. To charge the device, use a cable or a cradle with the appropriate power supply. For information about the accessories available for the device, see Accessories for more information.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or accessory always performs battery charging in a safe and intelligent manner. At higher temperatures (approximately +37°C (+98°F)) the device or accessory may, for small periods of time, alternately enable and disable battery charging to keep the
26
battery at acceptable temperatures. The device or accessory indicates when charging is disabled due to abnormal temperatures via its LED.
To charge the main battery:
1. Connect the charging accessory to the appropriate power source.
2. Insert the device into a cradle or attach to a cable. The device turns on and begins charging. The Charging/Notification LED blinks amber while charging, then turns solid green when fully charged.

Charging Indicators

Table 3 Charging/Notification LED Charging Indicators
State Indication
Off The device is not charging. The device is not inserted correctly in
Slow Blinking Amber (1 blink every 4 seconds)
Solid Green Charging complete.
Fast Blinking Amber (2 blinks/second) Charging error:
Getting Started
the cradle or connected to a power source. Charger/cradle is not powered.
The device is charging.
Temperature is too low or too high.
Charging has gone on too long without completion (typically eight hours).
Slow Blinking Red (1 blink every 4 seconds)
Solid Red Charging complete but the battery is at end of useful life.
Fast Blinking Red (2 blinks/second) Charging error but the battery is at end of useful life.

Google Account Setup

NOTE: You must connect the device to the internet in order to set up a Google™ account.
A Google account is only required on devices with GMS software.
The first time the device starts, the Setup Wizard displays. Follow the on-screen instructions to set up a Google account, configure Google Pay information, and enable backup or restore features.

Zebra Visibility Services

The device captures and provides device analytics to a system administrator. The first time the device boots (or after a Factory reset), the Zebra Services agreement screen displays.
The device is charging but the battery is at end of useful life.
Temperature is too low or too high.
Charging has gone on too long without completion (typically eight hours).
for purchasing items from the Google Play store, to enter your personal
27
Getting Started
Figure 15 Zebra Services
1. Touch the Device Data switch to disable the device from sending analytics data.
2. Touch OK.

Replacing the Battery

NOTE: User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc.,
may compromise the intended performance of the device or accessories. Performance levels such as sealing (Ingress Pro­tection (IP)), impact performance (drop and tumble), functionality, temperature resistance, etc. could be effected. DO NOT put any labels, asset tags, engravings, stickers, etc. in the battery well.
CAUTION: Do not add or remove SIM or microSD card during battery replacement.
3. Remove any accessory attached to the device.
4. Press the Power button until the menu appears.
5. Touch Battery Swap.
6. Follow the on-screen instructions.
7. Wait for the LED to turn off.
8. If hand strap is attached, slide the hand strap clip up toward the top of the device and then lift.
Figure 16 Remove Hand Strap Clip
28
9. Press the two battery latches in.
Figure 17 Press Battery Latches
Getting Started
10.Lift the battery from the device.
Figure 18 Lift the Battery
CAUTION: Replace the battery within two minutes. After two minutes the device reboots and data may be lost.
29
11.Insert the replacement battery, bottom first, into the battery compartment in the back of the device.
12.Press the battery down until the battery release latch snaps into place.
13.Replace the hand strap, if required.
14.Press and hold the Power button to turn on the device.
NOTE: After replacing the battery, wait 15 minutes before using Battery Swap again.

Replacing the SIM Card

NOTE: SIM replacement applies to TC75x only.
To replace the SIM card:
1. Press and hold the Power button until the menu appears.
2. Touch Power off.
3. Touch OK.
Getting Started
4. If hand strap is attached, slide the hand strap clip up toward the top of the device and then lift.
Figure 19 Remove Hand Strap Clip
5. Press the two battery latches in.
6. Lift the battery from the device.
7. Lift the access door.
Figure 20 Remove Access Door
30
8. Remove card from holder.
Figure 21 Remove Mini SIM Card
Figure 22 Remove Nano SIM Card
Getting Started
9. Insert the replacement card.
Figure 23 Insert Mini SIM Card
Figure 24 Insert Nano SIM Card
31
Getting Started
10.Replace the access door.
Figure 25 Replace Access Door
11.Press the access door down and ensure that it is properly seated.
12.Insert the battery, bottom first, into the battery compartment in the back of the device.
13.Press the battery down until the battery release latch snaps into place.
14.Replace the hand strap, if required.
15.Press and hold the Power button to turn on the device.

Replacing the microSD Card

To replace the microSD card:
1. Press the Power button until the menu appears.
2. Touch Power off.
3. Touch OK.
4. If hand strap is attached, slide the hand strap clip up toward the top of the device and then lift.
Figure 26 Remove Hand Strap Clip
5. Press the two battery latches in.
6. Lift the battery from the device.
32
Getting Started
7. Lift the access door.
Figure 27 Remove Access Door
8. Remove microSD card from holder.
9. Press the access door down and ensure that it is properly seated.
10.Insert the replacement microSD card.
11.Replace the access door.
Figure 28 Replace Access Door
12.Insert the battery, bottom first, into the battery compartment in the back of the device.
13.Press the battery down until the battery release latch snaps into place.
14.Replace the hand strap, if required.
15.Press and hold the Power button to turn on the device.

Accessing Device Settings

To access device settings:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. On the Home screen, swipe up from the bottom of the screen and touch .

Battery Management

NOTE: Prior to checking the battery charge level, remove the device from any AC power source (cradle or cable).
To check the charge status of the main battery, open Settings and touch System > About phone > Battery Information.
Battery present status indicates if the battery is present and Battery level lists the battery charge (as a
percentage of fully charged). The battery percentage can also be viewed next to the battery icon in the quick access panel. Swipe down with two fingers from the status bar to open the quick access panel.
33

Monitoring Battery Usage

The Battery screen provides battery charge details, power management options, and a list of apps that consume the most battery power.
Use the power management options to extend battery life, or touch an app to display details about its power consumption. Different apps display different information. Some apps include buttons that open screens with settings to adjust power use. Use the DISABLE or FORCE CLOSE buttons to turn off apps that consume too much power.
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Battery.
Figure 29 Battery Screen
Getting Started

Low Battery Notification

When the battery charge level drops below , the device displays a notice to connect the device to power. The user should charge the battery using one of the charging accessories.
When the battery charge drops below 10%, the device displays a notice to connect the device to power. The user must charge the battery using one of the charging accessories.
34
When the battery charge drops below 4%, the device turns off. The user must charge the battery using one of the charging accessories.
Figure 30 Low Battery Notification

Battery Optimization

Observe the following battery saving tips:
Set the screen to turn off after a short period of non-use.
Reduce screen brightness.
Turn off all wireless radios when not in use.
Turn off automatic syncing for Email, Calendar, Contacts, and other apps.
Minimize use of apps that keep the device from suspending, for example, music and video apps.
Getting Started

Turning Off the Radios

To turn off all the radios:
1. Swipe down from the Status bar to open the Quick Settings panel.
2. Touch Airplane mode. The airplane icon appears in the Status bar indicating that all the radios are off.

Setting the Date and Time

The date and time is automatically synchronized using an NITZ server when the device is connected to a cellular network. You are only required to set the time zone or set the date and time when not connected to a cellular network or if the wireless LAN does not support Network Time Protocol (NTP).
To set the date and time:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch System > Date & time.
3. Touch Automatic date & time to disable automatic date and time synchronization.
4. Touch Automatic time zone to disable automatic time zone synchronization.
5. Touch Set date.
6. In the calendar, set today’s date.
7. Touch OK.
35
8. Touch Set time.
9. Touch the green circle, drag to the current hour and then release.
10.Touch the green circle, drag to the current minute and then release.
11.Touch AM or PM.
12.Touch OK.
13.Touch Select time zone.
14.Select the current time zone from the list.
15.Touch Use 24-hour format.
16.Touch .

Display Settings

Use Display settings to change the screen brightness, enable night light, change the background image, enable screen rotation, set sleep time, and change font size.
Getting Started

Setting the Screen Brightness

To manually set the screen brightness using the touchscreen:
1. Swipe down with two fingers from the Status bar to open the Quick Access panel.
2. Slide the icon to adjust the screen brightness level.
Figure 31 Brightness Slider
To let the device automatically adjust the screen brightness using the built-in light sensor:
1. Swipe down from the status bar to open the quick settings bar and then touch .
2. Touch Display.
3. If disabled, touch Adaptive brightness to automatically adjust the brightness.
By default, Adaptive brightness is enabled. Toggle the switch to disable.
4. Touch .

Setting Screen Timeout

To set the screen sleep time:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Display > Advanced > Sleep.
36
3. Select one of the sleep values.
15 seconds
30 seconds
1 minute (default)
2 minutes
5 minutes
•10 minutes
30 minutes
4. Touch .

Ambient Display

The Ambient display setting wakes the screen when notifications are received.
To disable ambient display:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
Getting Started
2. Touch Display > Advanced.
3. Touch Ambient display.
4. In the When to show section, enable or disable an option using the switch.
5. Touch .

Setting Touch Key Light

The four touch keys under the screen are backlit.
To configure the touch key light to save battery power:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Display.
3. Touch Touch key light.
37
Getting Started
4. Select an option to choose how long the touch key light stays on:
Always off
6 seconds (default)
10 seconds
15 seconds
30 seconds
1 minute
Always on.
Figure 32 Touch Key Light Dialog Box
5. Touch .

Setting Font Size

To set the size of the font in system apps:
1. Swipe down from the Status bar to open the Quick Settings panel and then touch .
2. Touch Display > Advanced.
38
3. Touch Font size.
Figure 33 Font Settings
Getting Started
4. Select one of the font size values.
•Small
Default
•Large
Largest.
5. Touch .

Setting Screen Rotation

By default, screen rotation is enabled.
To disable screen rotation:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Display > Advanced.
3. Touch Auto-rotate screen.
NOTE: To change the Home screen rotation, see Setting Home Screen Rotation.
4. Touch .

Touch Panel Mode

The device display is able to detect touches using a finger, a conductive-tip stylus, or gloved finger.
39
Getting Started
NOTE: A glove can be made of medical latex, leather, cotton, or wool.
For optimal performance use a Zebra certified stylus.
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Display > Advanced.
3. Touch Touch panel mode.
Figure 34 Screen Protector Mode Dialog Box
4. Select:
a. Glove and Finger (Screen Protector off) to use a finger or a gloved finger on the screen without a
screen protector.
b. Stylus and Finger (Screen Protector off) to use a finger or a stylus on the screen without a screen
protector.
c. Glove and Finger (Screen Protector on) to use a finger or a gloved finger on the screen with a screen
protector.
d. Stylus and Finger (Screen Protector on) to use a finger or a stylus on the screen with a screen
protector.
5. Touch .

Setting Display Size

By default, display size is set to default.
To change the display size:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Display > Advanced.
3. Touch Display size.
4. Touch - and + to change the display size.
•Small
Default
•Large.
5. Touch .
40

General Sound Setting

Use the Sound settings to configure media and alarm volumes.
To access sound settings:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Sound.
3. Touch an option to set sounds.
Figure 35 Sound Screen
Getting Started
Zebra volume controls
Ring volume - Controls the ringtone volume.
Media volume - Controls the music, games, and media volume.
Alarm volume - Controls the alarm clock volume.
Notifications volume - Controls the notification volume.
Scanner volume - Controls the scanner volume.
Volume presets
- Mutes the ring, notifications, and scanner so that the device does not make sounds or vibrate.
- All sounds except media and alarms are silenced and vibrate mode is active.
- Enables all sounds at the user defined levels.
Also vibrate for calls - Switch on or off.
Do Not Disturb preferences - Mutes some or all sounds and vibrations.
Priority only allows - Use to set the priorities for the following:
Reminders - Switch on or off.
Events - Switch on or off.
Alarms - This is always enabled.
41
Getting Started
Messages - Choose to allow messages from anyone, starred contacts, any contact, or none. To star contacts, use the Contacts app.
Calls - Choose to allow calls from anyone, starred contacts, any contact, or none. To star contacts, use the Contacts app.
Repeat callers - Choose whether or not the phone rings if the same person calls again within 15 minutes.
Block visual disturbances
Block when screen is on - This option prevents notifications from displaying over the screen (peeking) while you are actively using the device.
Block when screen is off - This option prevents notifications from turning on the screen or pulsing the LED light when a new notification is received while you are not using the device.
Automatic rules - Choose when to automatically silence the device. Touch a default rule, such as Weekend or Weeknight, or create your own rule. To create your own rule, tap Add more and then Time rule.
Phone ringtone - Touch to select a sound to play when the phone rings.
Advanced - Touch to display advanced sound options.
Default notification sound - Touch to select a sound to play for all system notifications.
Default alarm sound - Touch to select a sound to play for alarms.
Other sounds and vibrations
Dial pad tones - Play a sound when pressing keys on dial pad (default - disabled).
Screen locking sounds - Play a sound when locking and unlocking the screen (default – enabled).
Charging sounds - Not applicable.
Touch sounds - Play a sound when making screen selections (default – enabledenabled).
Vibrate on tap - Vibrate the device when making screen selections (default – disabled).
Emergency alerts - Touch to configure emergency broadcast settings and notifications.

Wake-Up Sources

By default the device wakes from suspend mode when the user presses the power button. The device can be configured to wake when the user presses the PPT or Scan buttons on the left side of the device.
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch Wake-Up Sources.
3. Touch SCAN checkbox. A check appears in the checkbox.
4. Touch SCANTRIG_KEY checkbox. A check appears in the checkbox.
42
Getting Started
5. Touch LEFT_TRIGGER_2 checkbox. A check appears in the checkbox.
Figure 36 Wake-Up Sources
6. Touch .
43

Using the Device

Introduction

This chapter explains the buttons, status icons, and controls on the device, and provides basic instructions for using the device including resetting the device and entering data.

Google Mobile Services

NOTE: This section applies to Google Mobile Services (GMS) devices only.
Devices with GMS contain apps and services that provide additional functionality.
GMS includes:
Apps - GMS adds a variety of Google apps and associated widgets including Chrome, Gmail, Drive, and Maps.
Services:
Speech to Text - Allows for free format speech to text in many languages for both connected
and disconnected network. Launch by touching the microphone icon on the keyboard.
TalkBack Service - Provides spoken feedback on various parts of the user interface. To enable,
go to Settings > Accessibility.
Network Location Provider - Adds a location provider which uses mobile network tower
information and Wi-Fi access point information to provide a location without using GPS. To enable, go to Settings > Security & location > Location.
Widevine DRM - Enables Digital Rights Management (DRM) so that protected streaming video
content can be played. Enable DRM Info from the Google Play
Google Cloud Messaging - Allows the device to receive data from the server and other devices
on the same connection.
Backup and Restore - Allows the users settings and apps to be backed up to a Google server
and subsequently restored from that server after a factory reset.
Google Accounts - Create and use a Google account to synchronize mail, files, music, photos, contacts and calendar events.
store.

Home Screen

Turn on the device to display the Home screen. Depending on the configuration, the Home screen may appear different. Contact your system administrator for more information.
44
Using the Device
GMS Non-GMS
1
4
2
5
3
1
4
2
5
3
2
After a suspend or screen time-out, the Home screen displays with the lock slider. Touch the screen and slide up to unlock. For screen locking information, see Un-Locking the Screen.
The Home screen provides additional screens for placement of widgets and shortcuts. Swipe the screen left or right to view the additional screens.
NOTE:
By default, non-GMS devices do not have the same icons on the Home screen as GMS. Icons are shown below for example only.
Home screen icons can be configured by the user and may look different than shown.
Figure 37 Home Screen
Table 4 Home Screen Features
Item Description
1 Status Bar Displays the time, status icons (right side), and notification icons (left side).
For more information see Status Icons on page 47 and Managing
Notifications on page 49.
2 Widgets Launches stand-alone apps that run on the Home screen.
3 Shortcut Icons Opens apps installed on the device.
4 Folder Contains apps.
5 All Apps Opens the APPS window.
The Home screen provides four additional screens to place widgets and shortcuts. Swipe the screen left or right to view the additional screens.
45

Setting Home Screen Rotation

Notification Icons
Status Icons
By default the Home screen rotation is disabled.
To enable Home screen rotation:
1. Touch and hold anywhere on the Home screen until the options appear.
2. Touch HOME SETTINGS.
3. Touch the Allow Home screen rotation switch.
4. Touch .
5. Rotate the device.
Figure 38 Rotated Home Screen
Using the Device

Status Bar

The Status bar displays the time, notification icons (left side), and status icons (right side).
NOTE: Some Status icons may not appear in the Status bar if there are too many icons to display.
Figure 39 Notification and Status Icons
If there are more notifications than can fit in the Status bar, two dots display indicating that more notifications exist. Swipe down from the Status bar to open the Notification panel and view all notifications and status.
46
Using the Device
Status Icons
Table 5 Status Icons
Icon Description
Alarm is active.
Main battery is fully charged.
Main battery is partially drained.
Main battery charge is low.
Main battery charge is very low.
Main battery is charging.
All sounds, except media and alarms, are silenced and vibrate mode is active.
Do Not Disturb mode active.
Airplane Mode is active. All radios are turned off.
Bluetooth is on.
The device is connected to a Bluetooth device.
Connected to a Wi-Fi network.
Not connected to a Wi-Fi network or no Wi-Fi signal.
Connected to an Ethernet network.
Speakerphone enabled.
Portable Wi-Fi hotspot is active (WWAN only).
Connected to a 4G LTE/LTE-CA network (WWAN only)
1
.
Connected to a DC-HSPA, HSDPA, HSPA+, HSUPA, LTE/LTE-CA or WCMDMA network
1
(WWAN only)
.
Connected to a 1x-RTT (Sprint), EGDGE, EVDO, EVDV or WCDMA network (WWAN only)
1
.
Connected to a DC - HSPA, HSDPA, HSPA+ or HSUPA network (WWAN only)
Connected to an EDGE network (WWAN only)
1
Cellular network icon that appears is dependent upon the carrier/network.
1
.
47
1
.
Using the Device
Table 5 Status Icons (Continued)
Icon Description
Connected to a GPRS network (WWAN only)1.
Connected to a 1x-RTT (Verizon) network (WWAN only)
Roaming from a network (WWAN only).
No SIM card installed (WWAN only).
1
Cellular network icon that appears is dependent upon the carrier/network.
Notification Icons
Table 6 Notification Icons
Icon Description
Main battery is low.
1
.
More notifications are available for viewing.
Data is syncing.
Indicates an upcoming event. Non-GMS devices only.
Indicates an upcoming event. GMS devices only.
Open Wi-Fi network is available.
Song is playing.
Problem with sign-in or sync has occurred.
Device is uploading data.
Device is downloading data when animated and download is complete when static.
Device is connected via USB cable.
Device is connected to or disconnected from virtual private network (VPN).
Preparing internal storage by checking it for errors.
USB debugging is enabled on the device.
Call is in progress.
One or more voice message is in mailbox.
48
Table 6 Notification Icons (Continued)
Icon Description
Call is on hold.
Call was missed.
Headset is connected to the device.
PTT Express Voice client status. See the PTT Express PTT Notification Icons for a complete list.
Indicates that RxLogger app is running.
Indicates the Bluetooth scanner is connected to the device.
Indicates the RS507/RS507X or RS6000 is connected to the device in HID mode.

Managing Notifications

Using the Device
Notification icons report the arrival of new messages, calendar events, alarms, and ongoing events. When a notification occurs, an icon appears in the Status bar with a brief description. See Notification Icons for a list of possible notification icons and their description. Open the Notification panel to view a list of all the notifications.
To open the Notification panel, drag the Status bar down from the top of the screen.
Figure 40 Notification Panel
To respond to a notification, open the Notification panel and then touch a notification. The Notification panel closes and the corresponding app opens.
49
Using the Device
To clear all notifications, open the Notification panel and then touch CLEAR ALL. All event-based notifications are removed. Ongoing notifications remain in the list.
To close the Notification panel, swipe the Notification panel up.
Setting App Notifications
To set notification settings for a specific app:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Apps & notifications > Notifications > App notifications.
3. Select an app.
4. Select an available option:
On / Off - Select to turn all notifications from this app On (default) or Off.
Allow notification dot - Do not allow this app to add a notification dot to the app icon.
Allow interruptions - Do not allow notifications from this app to make sound, vibrate, or pop notifications on the screen.
Override Do Not Disturb - Allow these notifications to interrupt when Do Not Disturb is set to Priority Only.
Categories - Do not allow specific types of notifications from this app.
Additional settings in the app - Open the app settings.
NOTE: To change the notification settings for an app, slide the notification slightly left or right and touch .
Viewing Notification Settings for All Apps
To view the notification settings for all apps:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Apps & Notifications.
3. Scroll down to Notifications to view how many apps have notifications turned off.
4. To set or view notifications settings for a specific app, see Setting App Notifications.
Controlling Lock Screen Notifications
To control whether notifications can be seen when the device is locked:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Apps & notifications > Notifications.
3. Touch On the lock screen and select one of the following:
Show all notification content (default)
Don’t show notifications at all.
Blink Light
The Notification LED lights blue when an app, such as email and VoIP, generates a programmable notification or to indicate when the device is connected to a Bluetooth device. By default, LED notifications are enabled.
50
To change the notification setting:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Apps & notifications > Notifications.
3. Touch Blink light to toggle the notification on or off.

Quick Access Panel

Use the Quick Access panel to access frequently used settings (for example, Airplane mode).
Figure 41 Quick Settings Bar
To see the full Quick Access panel:
If the device is locked, swipe down once.
If the device is unlocked, swipe down once with two fingers, or twice with one finger.
If the Quick Settings bar is open, touch the Down arrow.
Using the Device
Figure 42 Quick Access Panel
NOTE: Not all icons are pictured. Icons may vary.
To change a setting, touch the icon:
Display brightness - Use the slider to decrease or increase the brightness of the screen.
Wi-Fi network - Turn Wi-Fi on or off. To open Wi-Fi settings, touch the Wi-Fi network name.
Bluetooth settings - Turn Bluetooth on or off. To open Bluetooth settings, touch Bluetooth.
Battery saver - Turn Battery saver mode on or off. When Battery saver mode is on the performance of the device is reduced to preserve battery power.
Do not disturb - Control how and when to receive notifications.
Mobile data - Turns cellular radio on or off. To open Mobile data settings, touch and hold(WAN only).
51
Using the Device
Airplane mode - Turn Airplane mode on or off. When Airplane mode is on the device does not connect to Wi-Fi or Bluetooth.
Flashlight - Turn flashlight on or off. Turn camera flash on or off.
The thermal protection safety feature for the camera provides the following behavior if the temperature range is 40°C or above:
If the flashlight is kept on for a certain period of time, it is automatically turned off and cannot be turned
back on for a period of time until it has cooled off.
During the cooling off period, the camera cannot be turned on. If you attempt to use the camera, a
message displays indicating to try again after a period of time.
Hotspot - Turn on to share the device’s mobile data connection with other devices.
Cast - Share phone content on Chromecast or a television with Google Cast built-in. Touch cast screen to display a list of devices, then touch a device to begin casting.
Editing Icons on Quick Settings
The first several setting tiles from the Quick Access panel become the Quick Settings bar.
To move a setting tile:
1. Open the Quick Access panel.
2. Touch .
3. Touch and drag a setting tile to another location.
4. Release the tile.
5. Touch to save tiles and return to the Quick Access panel.
To add a setting tile:
1. Open the Quick Access panel.
2. Touch .
3. Slide the Quick Settings panel up to reveal additional tiles.
4. Touch and drag a setting tile from the Drag to add tiles area to the main area.
5. Release the tile.
6. Touch to save tiles and return to Quick Access panel.
To remove a setting tile:
1. Open the Quick Access panel.
2. Touch .
3. Touch and drag a setting tile to the Drag here to remove area.
4. Release the tile.
5. Touch to save tiles and return to Quick Access panel.
52
Using the Device

App Shortcuts and Widgets

App shortcuts placed on the Home screen allow quick and easy access to apps. Widgets are self-contained apps placed on the Home screen to access frequently used features.
Adding an App Shortcut to the Home Screen
To add an app shortcut to the Home screen:
1. Go to the desired Home screen.
2. Swipe up from the bottom of the screen.
3. Scroll through the list to find the app icon.
4. Touch and hold the icon until the Home screen appears.
5. Position the icon on the screen and then release.
Adding a Widget to the Home Screen
To add a widget to the Home screen:
1. Go to the desired Home screen.
2. Touch and hold until the menu appears.
3. Touch WIDGETS.
4. Scroll through the list to find the widget.
5. Touch and hold the widget until the Home screen appears.
6. Position the widget on the screen and then release.
Moving Items on the Home Screen
To move app shortcuts or widgets on the Home screen:
1. Touch and hold the item until it floats on the screen.
2. Drag the item to a new location. Pause at the edge of the screen to drag the item onto an adjacent Home screen.
3. Lift finger to place the item on the Home screen.
Removing an App Shortcut or Widget from the Home Screen
To remove an app shortcut or widget from the Home screen:
1. Go to the desired Home screen.
2. Touch and hold the app shortcut or widget icon until it floats on the screen.
3. Drag the icon to
X
Remove at the top of the screen and then release.
53

Folders

Title Area

Creating a Folder

Naming Folders

Using the Device
Use Folders to organize similar applications together. Tap the folder to open and display items in the folder.
There must be at least two app icons on the Home screen.
To create a folder:
1. Go to the desired Home screen.
2. Touch and hold one app icon.
3. Drag the icon and stack on top of another icon.
4. Lift and release.
To name a folder:
1. Touch the folder.
Figure 43 Open Folder
2. Touch the title area and enter a folder name using the keyboard.
3. Touch on the keyboard.
4. Touch anywhere on the Home screen to close the folder. The folder name appears under the folder.

Removing a Folder

To remove a folder:
1. Touch and hold the folder icon until it enlarges.
2. Drag the folder to
X
Remove and release.

Home Screen Wallpaper

To change the Home screen wallpaper:
1. Touch and hold the screen until the menu appears.
2. Touch WALLPAPERS.
54
3. Touch Photos or Gallery to select a photo or select one of the pre-installed wallpapers.
4. Touch Set wallpaper.

Using the Touchscreen

Use the multi-tap sensitive screen to operate the device.
Tap - Tap to:
Select items on the screen.
Type letters and symbols using the on-screen keyboard.
Press on-screen buttons.
Tap and Hold - Tap and hold:
An item on the Home screen to move it to a new location or to the trash.
An item in Apps to create a shortcut on the Home screen.
The Home screen to open a menu for customizing the Home screen.
An empty area on the Home screen until the menu appears.
Drag - Tap and hold an item for a moment and then move finger on the screen until reaching the new position.
Swipe - Move finger up and down or left and right on the screen to:
Unlock the screen.
View additional Home screens.
View additional app icons in the Launcher window.
View more information on an app’s screen.
Double-tap - Tap twice on a web page, map, or other screen to zoom in and out.
Pinch - In some apps, zoom in and out by placing two fingers on the screen and pinching them together (to zoom out) or spreading them apart (to zoom in).
Using the Device

Keyboards

The device provides the following types of keyboards:
Android Keyboard - Non-GMS devices only.
Gboard - GMS devices only
Enterprise Keyboard
NOTE: By default the Enterprise and Virtual Keyboards are disabled.

Keyboard Configuration

Enabling Keyboards
To enable keyboards:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch System > Languages & input > Virtual keyboard > Manage keyboards.
55
Using the Device
3. Touch a keyboard to enable.
Switching Between Keyboards
To switch between keyboards, touch in a text box to display the current keyboard.
On the Android or Gboard keyboards, touch and hold .
On the Enterprise keyboard, touch .

Using the Android and Gboard Keyboards

Use the Android or Gboard keyboards to enter text in a text field. To configure the keyboard settings, touch and hold
, (comma) and then select Android keyboard settings.
Editing Text
Edit entered text and use menu commands to cut, copy, and paste text within or across apps. Some apps do not support editing some or all of the text they display; others may offer their own way to select text.
Entering Numbers, Symbols, and Special Characters
To enter numbers and symbols:
Touch and hold one of the top-row keys until a menu appears then select a number or special character.
Touch the Shift key once for a single capital letter. Touch the Shift key twice to lock in uppercase. Touch the Shift key a third time to unlock Capslock.
Touch
Touch the
To enter special characters, touch and hold a number or symbol key to open a menu of additional symbols. A larger version of the key displays briefly over the keyboard.
?123 to switch to the numbers and symbols keyboard.
=\< key on the numbers and symbols keyboard to view additional symbols.

Using the Enterprise Keyboard

The Enterprise Keyboard contains the following keyboards:
Numeric
•Alpha
Special characters
Data capture.
56
Using the Device
Numeric Tab
To access the numeric keyboard, touch the 123 tab. The keys displayed vary on the app being used. For example, an arrow displays in Contacts, however Done displays in Email account setup.
Figure 44 Numeric Keyboard
Alpha Tab
To access the alpha keyboard, touch the EN tab.
Figure 45 Alpha Keyboard
Additional Character Tab
To access additional characters, touch the #*/ tab.
Figure 46 Symbols Keyboard
57
Using the Device
Touch to enter emoji icons in a text message.
Figure 47 Emoji Keyboard
Touch ABC to return to the Symbols keyboard.
Scan Tab
The Scan tab provides an easy data capture feature for scanning barcodes.
Figure 48 Scan Keyboard

Do Not Disturb Feature

This mode mutes the device so that it does not make sounds or vibrate.
For example, use Do Not Disturb to:
Automatically limit sounds at night or during events
Mute interruptions other than alarms
Get alerted to messages only from favorite contacts.

Limit Sounds and Vibrations

Mute the device completely, or let through the important alarms or important calls.
Total Silence
To completely mute the device so that it does not make a sound or vibrate, choose Total silence.
In Total silence mode:
Alarms do not make noise.
Device does not vibrate or make sounds when receiving a message, or notification.
58
Using the Device
Sounds from music, videos, games, and other media are muted.
NOTE: All alarms are silenced in Total silence mode.
1. Swipe down with two fingers from the Status bar to open the Quick Access panel.
2. Touch Do not disturb > Total silence.
3. Choose Until you turn it off or select a time period.
4. Touch Done.
When Total Silence is on, appears in the quick access panel and the Status bar.
To turn off Total Silence, open quick access panel and touch Total silence.
Alarms Only
To mute the device so that you hear alarms, choose Alarms only. This option does not mute sounds from music, videos, games, or other media.
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Alarms only.
3. Choose Until you turn it off or select a time period.
4. Touch Done.
When Alarms Only is on, appears in the quick access panel and the Status Bar.
To turn off Alarms Only, open the Quick Access panel and touch Alarms only.
NOTE: To quickly turn on Alarms Only, with the screen on, press and hold the Volume Down button until the volume is all
the way down. Then, press Volume Down again to turn on Alarms Only.
To turn off Alarms Only, press either the Volume Up or Volume Down button and the touch END NOW in the alert message.
Priority Notifications Only
To only be interrupted by important notifications, choose Priority only. This option does not mute sounds from music, videos, games, or other media.
Before turning on Priority Only mode, set the notification priorities:
1. Swipe down from the status bar to open the quick settings bar and then touch .
2. Touch Sound > Do not disturb > Priority only allows.
3. Set priorities.
Alarms: Disabled by default.
Reminders and Events: Switch on or off.
Messages and Calls: Choose From anyone, From contacts only, From starred contacts only, or
none. To star contacts, use the Contacts applications.
Repeat callers: Choose whether to let the device ring if the same person calls again within 15 minutes.
59
Using the Device
After setting notification priorities, turn on Priority Only mode to limit interruptions. The priority notifications make a sound or vibrate based on the current ringer volume, but other notifications will be silenced.
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Priority only.
3. Choose Until you turn it off or select a time period.
4. Tap Done.
When Priority Only is on, appears in the quick access panel and the Status Bar.
To turn off Priority Only, open quick access panel and touch Priority only.

Automatically Block Sounds and Vibrations

Automatically silence the device during certain times or events, turn sounds back on, and override Do Not Disturb mode.
Silence Sounds During Certain Times
To automatically silence the device during certain times, like at night or on weekends:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Sound > Do Not Disturb preferences.
3. Touch a default Weekend or Weeknight. Or, to make a new rule, touch Add more > Time rule.
4. Enter a rule name.
5. Touch OK.
6. Edit the new rule:
Rule name - Rename the rule.
Days, Start time, and End time - Set the rule's schedule.
Do Not Disturb preferences - Choose whether the rule uses Alarms only, Priority only, or Total
silence.
Alarm can override end time - Allow the alarm to continue to make sound until the next alarm begins.
7. Touch the On/Off switch at the top to turn on the rule.
Silence Sounds During Events and Meetings
To automatically silence the device during events or meetings, set an event rules.
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Sound > Do Not Disturb preferences.
3. To edit the default rule, touch Event. Or, to create a new rule, touch Add rule > Event rule.
60
4. Edit the rule settings.
Rule name - Rename the rule.
During events for - Select which Google Calendar events the rule uses.
Where reply is - Set to: Yes, Maybe, or Not replied, Yes or Maybe, or Yes.
Do Not Disturb preferences - Choose whether the rule uses Priority only, Alarms only, or Total
silence.
5. Touch the On/Off switch at the top to turn on the rule.

Turn Sounds Back On

When the device is in Do Not Disturb mode, Alarms only or Priority only display as , or Total silence displays as .
To turn off Do Not Disturb, either:
In the Quick Access panel, touch Alarms only, Priority only, or Total silence.
Press the Volume Down button and touch End Now.
Using the Device

Override Do Not Disturb for Specific Apps

To let through notifications from specific apps:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Apps & notifications > Notifications > App notifications.
3. Touch an app.
4. Touch Override Do Not Disturb.

Apps

The APPS screen displays icons for all installed apps. The table below lists the apps installed on the device. Refer to the device Integrator Guide for Android Version 8.1 for information on installing and uninstalling apps.
Table 7 Apps
Icon Description
Battery Manager - Displays battery information, including charge level, status, health and wear
level.
Battery Swap – Use to place device in Battery Swap mode when replacing the battery.
Bluetooth Pairing Utility – Use to pair the RS507 Hands-free Imager with the device by
scanning a barcode.
61
Using the Device
Table 7 Apps (Continued)
Icon Description
Calculator - Provides the basic and scientific arithmetic functions.
Calendar - Use to manage events and appointments. GMS devices only
Calendar - Use to manage events and appointments. Non-GMS devices only.
Camera - Take photos or record videos. For more information see Camera.
Chrome - Use to access the Internet or intranet. GMS devices only
Chromium - Use to access the Internet or intranet. Non-GMS devices only.
Clock - Use to schedule alarms for appointments or as a wake-up.
Contacts - Use to manage contact information. See Contacts for more information.
DataWedge - Enables data capture using the imager.
Device Central - Use to display detailed information about the device and connected
peripherals. See Device Central for more information.
Diagnostic Tool - Use to diagnose the device.
Drive - Upload photos, videos, documents, and other files to personal storage site. GMS
devices only
Duo - A one-to-one video calling app (WWAN only).
DWDemo - Provides a way to demonstrate the data capture features using the imager. See
DataWedge Demonstration for more information.
62
Using the Device
Table 7 Apps (Continued)
Icon Description
Email - Use to send and receive email. Non-GMS devices only.
Files - Organize and manage files on the device. See Files for more information.
Gallery - Use to view photos stored on the microSD card. For more information, see Gallery for
more information. Non-GMS devices only.
Gmail - Use to send and receive email using a Google email account. GMS devices only
Google - Launches Google ™ search app. GMS devices only
Keep- Use to create, edit, and share notes. GMS devices only
License Manager - Use to manage software licenses on the device.
Maps - Use to see your location on a map (with public transit, traffic, or satellite overlays).
Search for any business or place of interest. Provides turn-by-turn navigation with voice guidance, traffic-avoidance, and alternate routes, for drivers, cyclists, walkers, and users of public transportation. GMS devices only
Messaging - Send SMS and MMS messages. See Messaging for more information. WAN devices only.
MSRN - Use to verify authenticity of the paired Snap-on MSR and to provision the Snap-on MSR. See device Touch Computer Integrator Guide for Android Version 8.1 for more information.
Music - Play music stored on the microSD card or internal storage. Non-GMS devices only.
Notes - Use to take and save notes.Non-GMS devices only
Phone - Use to dial a phone number when used with some Voice over IP (VoIP) clients (VoIP
telephony ready only).
Photos - Use to sync photos with Google account. For more information, see Photo Settings. GMS devices only
63
Using the Device
Table 7 Apps (Continued)
Icon Description
Play Movies & TV - View movies and video on your device. GMS devices only
Play Music - Use to listen to music. GMS devices only
Play Store - Download music, movies, books, and Android apps and games from the Google
Play Store. GMS devices only
PTT Express - Use to launch PTT Express client for VoIP communication.
RxLogger - Use to diagnose device and app issues. See the device Integrator Guide for
Android Version 8.1 for more information.
RxLogger Utility - Use to view, backup, and archive RxLogger data.
Search - Use to search the Web. Requires an Internet connection. Non-GMS devices only.
Settings - Use to configure the device.
SimulScan Demo - Use to demonstrate the document capture feature of the device.
Sound Recorder - Use to record audio.
StageNow - Allows the device to stage a device for initial use by initiating the deployment of
settings, firmware, and software.
YouTube - Use to view videos on the YouTube
web site. GMS devices only
Zebra Bluetooth - Use to configure Bluetooth logging.

Accessing Apps

All apps installed on the device are accessed using the APPS window.
64
Using the Device
1. On the Home screen, swipe up from the bottom of the screen.
Figure 49 APPS Window Example
Slide the APPS window up or down to view more app icons. Touch an icon to open the app.

Switching Between Recent Apps

To switch between recent apps:
65
Using the Device
1. Touch . A window appears on the screen with icons of recently used apps.
Figure 50 Recently Used Apps
1
2. Slide the apps displayed up and down to view all recently used apps.
3. Swipe left or right to remove app from the list and force close the app.
4. Touch an icon to open an app or touch to return to the current screen.

Un-Locking the Screen

Use the Lock screen to protect access to data on the device. Some email accounts require locking the screen. Refer to the device Integrator Guide for information on setting up the locking feature.
When locked, a pattern, PIN, or password is required to unlock the device. Press the Power button to lock the screen. The device also locks after a pre-defined time-out.
66
Using the Device
Press and release the Power button to wake the device. The Lock screen displays. Swipe the screen up to unlock. If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen. If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
Figure 51 Lock Screen
Figure 52 PIN Screen
67
Figure 53 Pattern Screen
Using the Device
Figure 54 Password Screen

Interactive Sensor Technology

The device contains sensors that monitor movement, orientation and ambient light:
Gyroscope - Measures angular rotational velocity to detect rotation of the device.
68
Accelerometer - Measures the linear acceleration of movement to detect the orientation of the device.
Digital Compass - The digital compass or magnetometer provides simple orientation in relation to the Earth's magnetic field. As a result, the device always knows which way is North so it can auto rotate digital maps depending on the physical orientation of the device.
Light Sensor - Detects ambient light and adjusts the screen brightness.
Proximity Sensor - Detects the presence of nearby objects without physical contact.
In order to take advantage of these sensors, applications use API commands. Refer to the Zebra Android EMDK for more information.

Resetting the Device

There are two reset functions, soft reset and hard reset.

Performing a Soft Reset

Perform a soft reset if applications stop responding.
1. Press and hold the Power button until the menu appears.
Using the Device
2. Touch Restart.
3. The device reboots.

Performing a Hard Reset

CAUTION: Performing a hard reset with a SD card installed in the device may cause damage or data corruption to the SD
card.
Perform a hard reset if the device stops responding.
1. Simultaneously press the Power, Scan and Volume Up buttons for at least four seconds.
2. When the screen turns off, release the buttons.
3. The device reboots.

Suspend Mode

The device goes into suspend mode when you press the Power buttonor after a period of inactivity (set in the Display settings window).
To wake the device from Suspend mode, press the Power button. The Lock screen displays. Swipe the screen up to unlock. If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen. If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen. See Un-Locking the Screen.
NOTE: If you enter the PIN, password, or pattern incorrectly five times, you must wait 30 seconds before trying again.
If you forget the PIN, password, or pattern contact your system administrator.
69
Using the Device

Transferring Files with a Host Computer via USB

Connect the device to a host computer using a USB cable or a USB cradle to transfer files between the device and the host computer.
When connecting the device to a host computer, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.

Transferring Files

NOTE: Use Transfer files to copy files between the device (internal memory or microSD card) and the host computer.
1. Connect a USB cable to the device or place the device into a USB cradle.
2. Pull down the Notification panel and touch USB charging this device.
By default, Charge this device is selected.
Figure 55 Use USB to Dialog Box
3. Touch Transfer files.
4. On the host computer, open a file explorer application.
5. Locate the device as a portable device.
6. Open the SD card or the Internal storage folder.
7. Copy files to and from the device or delete files as required.

Transferring Photos

To transfer photos using Photo Transfer Protocol:
NOTE: Use Photo Transfer Protocol (PTP) to copy photos from either the microSD card or internal memory to the host com-
puter.
1. Connect USB cable to the device or place the device into a USB cradle. See Accessories for setup information.
2. Pull down the Notification panel and touch USB charging this device.
3. Touch Transfer photos (PTP).
70
Using the Device
4. On the host computer, open a file explorer application.
5. Open the SD card or the Internal storage folder.
6. Copy or delete photos as required.

Disconnect from the Host Computer

To disconnect the device from the host computer:
CAUTION: Carefully follow the host computer’s instructions to unmount the microSD card and disconnect USB devices cor-
rectly to avoid losing information.
1. On the host computer, unmount the device.
2. Remove the USB cable from the device or remove the device from the cradle.
71

Applications

Introduction

This section describes the applications installed on the device.

Battery Manager

The Battery Manager provides detailed information about the battery.
To open Battery Manager, swipe up from the bottom of the Home screen and touch .
Figure 56 Battery Manager Screen
72
Table 8 Battery Icon Description
Applications
Battery
Icon
Battery charge level.
Battery charging.
Battery charge level is below 20%.
Battery level - The current battery charge level as a percentage. Displays -% when level is unknown.
Time until full - The amount of time until the battery is fully charged.
Time since charging - The amount of time since the device began charging.
Time until empty - The amount of time until the battery is empty.
Battery status
Not charging - The device is not charging.
Charging over AC - The device is connected to AC power and charging.
Charging over USB - The device is connected to a host computer with a USB cable and charging.
Discharging - That the battery is discharging.
Full - That the battery is fully charged.
Unknown - The battery status is unknown.
Description
Battery health - The health of the battery. If a critical error occurs, appears. Touch to view the error description.
Decommission - The battery is past its useful life and should be replaced. See system administrator.
Good - The battery is good.
Charge error - An error occurred while charging. See system administrator.
Over Current - An over-current condition occurred. See system administrator.
Dead - The battery has no charge. Replace the battery.
Over Voltage - An over-voltage condition occurred. See system administrator.
Below Temperature - The battery temperature is below the operating temperature. See system
administrator.
Failure Detected - A failure has been detected in the battery. See system administrator.
Unknown - See system administrator.
Wear level - The health of the battery in graphical form. When the wear level exceeds 80%, the bar color changes to red.
73
Applications
Advanced info - Touch to view additional battery information.
Battery present status - Indicates that the battery is present.
Battery level - The battery charge level as a percentage of scale.
Battery scale - The battery scale level used to determine battery level (100).
Battery voltage - The current battery voltage in millivolts.
Battery temperature - The current battery temperature in degrees Centigrade.
Battery technology - The type of battery.
Battery current - The average current into or out of the battery over the last second in mAh.
Battery manufacture date - The date of manufacture.
Battery serial number - The battery serial number. The number matches the serial number printed on
the battery label.
Battery part number - The battery part number.
Battery rated capacity - Lists the rated capacity of the backup battery in mAh.
Battery decommission status - Indicates if the battery is past its life span.
Battery Good - The battery is in good health.
Decommissioned Battery - The battery is past its useful life and should be replaced.
Base cumulative charge - Cumulative charge using Zebra charging equipment only.
Battery usage number - The health of the battery as a result of charging and discharging. A high
number indicates low battery health.
Usage decommission threshold - When the Battery usage number is greater than or equal to the
Usage decommission threshold, the battery is past its useful life and should be replaced.
App version - The application version number.
74

Camera

Camera Mode
Settings
High Dynamic Range
Camera Switch (Available on devices with a rear camera and front camera)
Scene Mode
Shutter Button
Gallery
This section provides information for taking photos and recording videos using the integrated digital cameras.
The device saves photos and videos on the microSD card, if installed and the storage path is changed manually. By default, or if a microSD card is not installed, the device saves photos and videos on the internal storage.

Taking Photos

NOTE: See Photo Settings for camera setting descriptions.
1. Swipe up from the bottom of the Home screen and touch Camera.
Figure 57 Camera Mode
Applications
2. If necessary, touch the Camera Mode icon and touch .
3. To switch between the rear camera and front camera (if available), touch .
4. Frame the subject on the screen.
75
5. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
6. Touch an area on the screen to focus. The focus circle appears. The two bars turn green when in focus.
7. Touch .
The camera takes a photo and a shutter sound plays.
The photo momentarily displays as a thumbnail in the lower left corner.

Taking a Panoramic Photo

Panorama mode creates a single wide image by panning slowly across a scene.
1. Swipe up from the bottom of the Home screen and touch Camera.
Figure 58 Panoramic Mode
Applications
2. Touch the Camera Mode icon and touch .
3. Frame one side of the scene to capture.
4. Touch and slowly pan across the area to capture. A small white square appears inside the button indicating the capture is in progress.
If you are panning too quickly, the message Too fast appears.
5. Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves the image.
76

Recording Videos

Camera Mode
Settings
Audio
Camera Switch (Available on devices with a rear camera and front camera)
Shutter Button
Gallery
1. Swipe up from the bottom of the Home screen and touch Camera.
2. Touch the camera mode menu and touch .
Figure 59 Video Mode
Applications
3. To switch between the rear camera and front camera (if available), touch .
4. Point the camera and frame the scene.
5. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
6. Touch to start recording.
The video time remaining appears in the top left of the screen.
7. Touch to the end recording.
The video momentarily displays as a thumbnail in the lower left corner.
77

Photo Settings

In Photo mode, photo settings appear on screen. Touch to display the photo settings options.
Rear Camera
Flash - Select whether the camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
Off - Disable flash.
Auto - Adjust flash automatically depending upon light meter (default).
On - Enable flash upon taking a photo.
Torch - Turn flash on continuously.
GPS location - Turn On or Off (default).
Picture size - The size (in pixels) of the photo to: 13M pixels (default), 8M pixels, 5M pixels, 3M pixels, HD 1080, 2M pixels, 1.3M pixels, HD720, 1M pixels, WVGA, VGA, or QVGA.
Picture quality - Set the picture quality setting to: Low, Standard (default) or High.
Countdown timer - Select Off (default), 2 seconds, 5 seconds or 10 seconds.
Storage – Set the location to store the photo to: Phone or SD Card.
Face Detection - Select to turn face detection Off (default) or On.
ISO - Set camera sensitivity to light to: Auto (default), ISO Auto (HJR), ISO100, ISO200, ISO400, ISO800 or ISO1600.
Exposure - Set the exposure settings to: +2, +1, 0(default), -1 or -2.
White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors:
Applications
Incandescent - Adjust the white balance for incandescent lighting.
Fluorescent - Adjust the white balance for florescent lighting.
Auto - Adjust the white balance automatically (default).
Daylight - Adjust the white balance for daylight.
Cloudy - Adjust the white balance for a cloudy environment.
Focus mode - Set the camera focus to CAF (Continuous Auto Focus).
ZSL - Set the camera to immediately take a picture when the button is pressed (default – enabled).
Front Camera
GPS location - Add GPS location information to the photo meta-data. Options: On or Off (default).
Picture size - Set the size (in pixels) of the photo to: 1.3M pixels (default), HD720, 1M pixels, WVGA, VGA, or QVGA.
Picture quality - Set picture quality setting to: Low, Standard (default) or High.
Countdown timer - Set to: Off (default), 2 seconds, 5 seconds or 10 seconds.
Storage – Set location to store the photo to: Phone or SD Card.
78
Face Detection - Select to turn face detection Off (default) or On.

Video Settings

In Video mode, video settings appear on screen. Touch to display the video settings options.
Rear Camera
Flash - Select whether Rear-facing Camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
Off - Disable flash (default).
Torch - Turn flash on continuously.
Video quality - Set video quality to: HD 1080p (default), HD 720p, SD 480p.
Video duration - Set to: 30 seconds (MMS), or 30 minutes (default).
GPS location - Turn On or Off (default).
Storage – Set the location to store the photo to: Phone (default) or SD Card.
White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
Applications
Incandescent - Adjust the white balance for incandescent lighting.
Fluorescent - Adjust the white balance for florescent lighting.
Auto - Adjust the white balance automatically (default).
Daylight - Adjust the white balance for daylight.
Cloudy - Adjust the white balance for a cloudy environment.
Front Camera
Video quality - Set video quality to: HD 720p (default), or SD 480p.
Video duration - Set to: 30 seconds (MMS) or 30 minutes (default).
GPS location - Turn On or Off (default).
Storage – Set the location to store the photo to: Phone (default) or SD Card.
79

Contacts

Use the Contacts app to manage contacts.
From a Home or Apps screen, touch Contacts to open to the main list of contacts. Contacts are listed in alphabetical order. Swipe up or down to scroll through the list.

Adding a Contact

1. In the Contacts app, touch .
2. If there is more than one account with contacts, touch the one you want to use.
3. Type the contact’s name and other information. Touch a field to start typing, and swipe down to view all categories.
4. To open a menu with preset labels, such as Home or Work for an email address, touch the label to the right of the item of contact information. Or, to create your own label, touch Custom in the menu.
5. Touch the check mark next to Add New Contact.
Applications

Editing Contacts

1. In the Contacts app, touch a contact name to edit.
2. Touch .
3. Edit the contact information.
4. Touch SAVE.

Deleting Contacts

1. In the Contacts app, touch a contact name to delete.
2. Touch .
3. Touch Delete.
4. Touch DELETE to confirm.
80

DataWedge Demonstration

NOTE: DataWedge is enabled on the Home screen.To disable this feature, go to the DataWedge settings and disable the
Launcher profile.
Use DataWedge Demonstration to demonstrate data capture functionality.
Figure 60 DataWedge Demonstration Window
Applications
Table 9 DataWedge Demonstration Icons
Icon Description
Illumination Imager illumination is on. Touch to turn illumination off.
Imager illumination is off. Touch to turn illumination on.
Data Capture The data capture function is through the internal imager.
An RS507 or RS6000 Bluetooth imager is connected.
An RS507 or RS6000 Bluetooth imager is not connected.
81
Table 9 DataWedge Demonstration Icons (Continued)
Scan Mode Imager is in picklist mode. Touch to change to normal scan mode.
NOTE: See the device Integrator Guide for Android Version 8.1 for information on DataWedge configuration.

Scanner Selection

To select a scanner, touch > Settings > Scanner selection.
See Data Capture for more information.
Applications
Icon Description
Imager is in normal scan mode. Touch to change to picklist mode.
Opens a menu to view the application information or to set the application DataWedge profile.
Either press the programmable button or touch the yellow scan button to capture data. The data appears in the text field below the yellow button.

Device Central

Device Central displays detailed information about the device and connected peripherals and supports the
following Zebra devices:
RS507/RS507X Hands-free Imager
RS6000 Bluetooth Ring Scanner
RS5000 Corded Ring Scanner
HS3100 Bluetooth Headset
DS3678 Digital Scanner.
Device Central features include:
Discovering and pairing with supported peripherals via Bluetooth or corded connection.
Paging a connected RS6000 Ring Scanner.
Updating the firmware of supported ring scanners. Refer to the RS5000 Quick Start Guide or RS6000 User Guide for more information.
Displaying the connection status of peripherals.
Displaying information for a connected peripheral in the notification bar.

Device Central Tabs

Peripherals Tab - displays all currently connected and previously connected peripherals. Connected peripherals display the length of time (in minutes) that they have been connected. When an RS6000 is connected the Page button displays. See Paging an RS6000 Ring Scanner.
82
Applications
Touch the peripheral information to display the Device Details screen.
Device Details - displays detailed device information for the selected peripheral.
My Device Tab - displays information about the device and the current version of Device Central.
Device Details - displays the Phone status screen.
Device Battery Details - displays the Battery screen.
Figure 61 Peripherals Tab

Paging an RS6000 Ring Scanner

Use Page button to easily locate the currently connected RS6000 Ring Scanner:
1. With the RS6000 Ring Scanner connected, swipe up from the bottom of the Home screen, and touch .
NOTE: The RS6000 Ring Scanner must be within 10 m (32 ft) of the device.
83
Applications
2. Under the RS6000 peripheral information, touch Page to page the RS6000. The paged RS6000 beeps and vibrates.
Figure 62 Page RS6000
To stop paging, press the scan trigger of the RS6000. On a triggerless RS6000, reset the RS6000 to stop paging. Refer to the RS6000 User Guide.
84

Diagnostic Tool

The Diagnostic Tool is a utility that determines the health of the device. Use the Diagnostic Tool to troubleshoot the device.
1. Swipe up from the bottom of the Home screen and touch .
Figure 63 Diagnostic Tool
Applications
2. Touch RUN TEST. The app tests all enabled subsystems (by default, only the Battery and System tests). See Settings to enable subsystem tests.
85
Figure 64 Test Passed Screen
Applications
Figure 65 Test Failed Screen
3. To view each subsystem test, touch Subsystem Tests.
86
Figure 66 Subsystem Screen
Applications
4. Touch one of the subsystems to view details.
Table 10 Subsystem Test Result Indicators
Status Icon Description
Test passed.
Test failed.
Test not supported or not enabled.
87
Figure 67 Battery Subsystem Details
Applications

Settings

By default only the Battery and System tests are enabled. To enable other tests:
1. Touch > Settings.
2. Touch to the left of the test name. A green box with a checkmark appears.
3. Touch SAVE.
4. Touch Yes to confirm.
5. Touch .

Battery Test Information

The Battery Test obtains the following information:
Battery Level - Current battery charge level
Battery Voltage - Current battery voltage
Status - Whether the battery is charging (on AC power) or discharging (on battery power)
Power Source - Whether the device is receiving power from the battery or from an external source
Temperature - Current battery temperature
Health Percentage - Indicates the ratio of present capacity to design capacity at a discharge rate of design capacity.
Backup Battery Voltage - Backup battery voltage.
Manufacture Date - Manufacture date of the battery.
88

GPS Test Information

The GPS Test obtains the following information (WWAN only):
GPS Provider Enabled - Whether GPS is enabled (true) or disabled (false)
Latitude - Current latitude position
Longitude - Current longitude position
Altitude - Current altitude in meters
Bearing - Current bearing
Speed - Speed in meters per second
Accuracy - GPS accuracy in meters.
Not supported on this device.

System Test Information

Use the System Test to determine if the CPU or memory loads are too high, there are too many processes running on the device, or storage on the device is almost full.
Applications
The System Test obtains the following information:
CPU Load - Amount of CPU being used
Free Physical Memory - Amount of RAM available
Free Storage - Amount of internal Flash memory available
Process Count - Number of processes currently running.

WLAN Test Information

If the WiFi radio is not present or disabled, skip this test. This test determines if the device’s WLAN configuration is correct or whether there is any connection with an access point or network.
The WLAN test obtains the following information:
WLAN Enabled - WLAN radio is enabled or disabled
WLAN Status - Current status of association with the access point
ESSID - Name of the wireless network
BSSID - MAC address of the connected access point
MAC Address - Device’s MAC address
Signal - Strength of the Wi-Fi signal (in dBm)
IP Address - IP address of the device.

WWAN Test Information

The WWAN Test obtains the following information (WWAN only):
SIM State - Current state of the SIM card
WAN Type - Data connection type
Signal Strength - Current cellular signal strength
89
Phone Number - Phone number assigned to the device
Device ID - Device ID number.
Not supported on this device.

Bluetooth Test Information

The Bluetooth Test obtains the following information:
Enabled - Whether the Bluetooth radio is enabled or disabled
Status - Whether the device is paired to another Bluetooth device
Connectable/Discoverable - Whether the device is discoverable or able to connect
Address - Bluetooth radio MAC address
Name - Bluetooth name for the device.
Applications
90

Files

Sort
Applications
Use the Files app to view and manage files on the device.
To open Files, swipe up from the bottom of the screen and touch .
Figure 68 Files Screen
Touch and hold an item to open the File Operations menu. Select an option:
- Share the file with other devices.
- Delete the file.
- View additional options.
Open with - Select which app is used to open the file.
Select all - Select all folders and files.
Copy to... - Copy the file.
Move to... - Move the file or folder to a new location.
Compress - Compress the selected file(s) into a ZIP file.
Rename - Rename the file.
Touch the Sort drop-down to sort files by name, type, size, or date.
- View all file locations.
- Search for a specific file on the device.
/ - Change the folder to display items as a list / grid.
- Open the options menu.
New Window - Create a new Files window.
New Folder - Create a new folder.
Select all - Select all folders and files.
Show/Hide internal storage - Show or hide internal storage.
91

Gallery

Applications
NOTE: The device supports the following image formats: jpeg, gif, png and bmp.
The device supports the following video formats: H.263, H.264 and MPEG4 Simple Profile.
Available on device with AOSP only.
Use Gallery to:
View photos
Play videos
Perform basic editing of photos
Set photos as wallpaper
Set photos as a contact photo
Share photos and videos.
Gallery presents all photos and videos stored on the microSD card and internal memory.
To open Gallery, swipe up from the bottom of the Home screen and touch Gallery, or in the camera app touch the thumbnail image at the bottom left.
By default, Gallery opens to the Timeline view.
Figure 69 Gallery - Timeline View
92
Applications
Touch > Albums to view photos sorted by albums or > Videos to view only videos.
Figure 70 Gallery — Albums View
Touch an album to open it and view its contents. The photos and videos in the album are displayed in chronological order.
Touch a photo or video in an album to view it.
•Touch > Timeline to return to the default Gallery screen.
93

Working with Albums

Albums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in a chronologically ordered grid. The name of the album displays at the top of the screen.
Figure 71 Photos Inside an Album
Applications
Swipe up or down to scroll through the images.
Sharing an Album
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch and hold an album to highlight it.
3. Touch other albums as required.
4. Touch . The Share menu opens.
5. Touch the app to use to share the selected albums.
6. Follow the instructions within the selected app.
Getting Album Information
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch and hold an album to highlight it.
3. Touch .
4. Touch Details.
94
Deleting an Album
To delete an album and its contents:
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch and hold an album to highlight it.
3. Check other albums to delete.
4. Touch .
5. In the Delete selected item? menu, touch OK to delete the album.

Working with Photos

Use Gallery to view photos on the device and edit and share photos.
Viewing and Browsing Photos
To view a photo:
Applications
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch an album to open it.
3. Touch a photo.
Figure 72 Photo Example
4. Swipe left or right to view the next or previous photo in the album.
5. Turn the device to view the photo in upright (portrait) or sideways (landscape) orientation. The photo is displayed (but not saved) in the new orientation.
6. Touch the photo to view the controls.
95
Applications
7. Double-tap the screen to zoom in or pinch two fingers together or spread them apart to zoom in or out.
8. Drag the photo to view parts that are not in view.
Cropping a Photo
1. In Gallery, touch a photo to view the controls.
2. Touch > > . The cropping tool appears.
3. Use the cropping tool to select the portion of the photo to crop.
Drag from the inside of the cropping tool to move it.
Drag an edge of the cropping tool to resize it to any proportion.
Figure 73 Cropping Tool
4. Touch > SAVE to save a copy of the cropped photo. The original version is retained.
Setting a Photo as a Contact Icon
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch an album to open it.
3. Touch a photo to open it.
4. Touch .
5. Touch Set picture as.
6. Touch Contact photo.
7. In Contacts, touch a contact.
8. Touch the white box and crop the photo accordingly.
96
Applications
9. Touch SAVE.
Sharing a Photo
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch an album to open it.
3. Touch a photo to open it.
4. Touch .
5. Touch the app to use to share the selected photo.
6. Follow the instructions within the selected app.
Deleting a Photo
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch an album to open it.
3. Touch a photo to open it.
4. Touch .
5. Touch OK to delete the photo.

Working with Videos

Use Gallery to view and share videos.
Watching Videos
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch an album to open it.
3. Touch a video.
4. Touch to play.
5. Touch the screen to view the playback controls.
Sharing a Video
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch an album to open it.
3. Touch a video to open it.
4. Touch . The Share menu appears.
5. Touch the app to use to share the selected video.
6. Follow the instructions within the selected app.
97
Applications
Deleting a Video
1. Swipe up from the bottom of the Home screen and touch Gallery.
2. Touch an album to open it.
3. Touch a video to open it.
4. Touch .
5. Touch OK.
98

Messaging

NOTE: WWAN Only.
Use Messaging to send and receive SMS and MMS messages.
To open Messaging, swipe up from the bottom of the screen and touch Messaging.

Sending a Text Message

1. In the main Messaging screen, touch .
Figure 74 New Text Message Screen
Applications
2. In the To field, enter a name or a mobile phone number.
3. In the Send message field, enter the text message.
The 160-character limit counter indicates how many characters are left. If it exceeds the limit, a new message is created, which is joined with its predecessors when received.
Press the Back button while composing a message to save it as a draft in the Messaging screen. Touch the conversation to resume composing it.
4. Touch to send message.

Sending a Multimedia Message

1. In the main Messaging screen, touch .
2. In the To field, enter a name or a mobile phone number.
99
Applications
3. Touch to attach the media file of your choice.
Figure 75 New Multimedia Message Screen
Subject - Enter a message subject.
Pictures - Select a picture to attach.
Capture picture - Open the Camera to take a picture and attach it.
Videos - Select a video to attach.
Capture video - Open the Camcorder to record a video and attach it to the message.
Audio - Choose a sound file to attach.
Record audio - Open the Sound Recorder to record a spoken message and attach it to the message.
Slideshow - Open a screen opens to assemble text, photos, videos, and recordings into a slideshow of
up to 10 slides to attach to the message.
Insert contact info - Open the Contacts app and select one or more contacts to insert the contact
information into the message.
Contact vCard - Send a contact’s information.
Import Template - Import a message template.
4. Touch to send the message.
100
Loading...