TC70
QUICK START
FEATURES
Note: Remove protective shipping film that covers the touch screen, exit
window and camera window before using.
CARD INSTALLATION
23
MicroSD Card Installation (Optional)
1. Lift the access door.
HANDSTRAP AND BATTERY INSTALLATION BATTERY INSTALLATION
1. Remove hand strap filler plate.
4. Rotate the battery down into the battery compartment and press the battery
down until it snaps into position.
BATTERY INSTALLATION
1. Insert the bottom of the battery into the battery compartment.
GUIDE
11
12
13
14
15
1
2
3
10
9
8
4
1 PTT Button (programmable)
2 Scan Button
3 Back Button
4 Home Button
5 Power Input
6 Search Button
7 Menu Button
8 Touch Screen
9 Light Sensor
10 Proximity Sensor
11 Power Button
12 Receiver
13 Charging/Notification LED
14 Data Capture LED
15 Front-facing Camera
Note 1: To reset the TC70, press and hold the Power button until the menu
appears and then select Reset.
16
17
18
19
7
6
20
16 Hand Strap Mounting Point
17 Camera Flash
18 Rear-facing Camera
5
19 Interface Connector
20 Exit Window
21 Volume Button
22 Battery Release Latch
23 Hand Strap
22
2. Insert the microSD card into the card holder. Push the card all the way into the
card holder.
NOTE :
21
Proper position of the microSD card — the card connector (i.e., gold contacts) should
be facing down.
2. Insert the hand strap plate into the handstrap slot.
2
2. Rotate the battery down into the battery compartment.
5. Place the hand strap clip into the hand strap attachment slot and pull down to lock into
place.
3
Notifications
Data Capture LED:
Green: Good Decode
Red: Data capture in process
Blue: Application notification
Charging\Notification LED:
Slow blinking amber: Battery charging
Solid green: Fully charged
Fast blinking amber: Charging error
Slow blinking red: Charging aged battery
Solid red: Fully charged aged battery
Fast blinking red: Charging error aged battery
Slow blinking blue: Application notification
Charging/Notification
Data Capture
3. Replace the access door. Ensure that it is properly seated.
3. Insert the bottom of the battery into the battery compartment.
3. Press the battery down until it snaps into position.
6. Lift the hand strap ribbon off the hook material.
4
7. Slide the pad and adjust the ribbon for best fit.
8. Press the ribbon down to secure to hand strap.
BATTERY REMOVAL
ACCESSORIES
DATA CAPTURE OPTIONS
AVOID EXTREME WRIST ANGLES
1. Press the Power button until
the menu appears.
2. Touch Power Off.
3. If installed, unlatch the hand
strap. Push the hand strap clip
up toward the top of the TC70
and then lift.
4. Press the battery release
latches in and lift the battery
from the TC70.
Symbol Technologies, Inc.
Holtsville, NY 11742-1300, U.S.A.
Symbol® is a registered trademark of Symbol Technologies, Inc. All other
trademarks and service marks are proprietary to their respective owners.
© 2014 Symbol Technologies, Inc. All rights reserved.
5-Slot Charge Only Cradle
5-Slot Charge Only Cradle
with Battery Charger
5-Slot Ethernet Cradle
2-Slot Charge
Only Cradle
Magnetic Stripe Reader Charging Cable Cup
4-Slot Battery
Charger
2-Slot USB/Ethernet Cradle
Snap-On USB Cable
Stylus
with Tether
Battery
Charger Adapter
Audio Adapter
Holster
Imaging
1. Ensure that an application is open and a text field is in focus
(text cursor in text field).
2. Point the exit window at the bar code.
3. Press and hold the Scan button.
4. The red laser aiming pattern turn on to assit in aiming.
When the TC70 decodes the bar code the Data Capture LED
light green and a beep sounds.
5. Release the Scan button.
Camera Photo
1. Touch > Camera.
2. Point the TC70 at an object.
3. Touch the on-screen shutter button.
AVOID EXTREME
WRIST ANGLES
MN000976A02 Rev. A — March 2015
For more information, see the TC70 User Guide and the TC70 Integator
Guide available at: http://www.zebra.com/support.
Loading...