CRD-TC58-WCVC-01
Wireless Charging
Vehicle Cradle
Installation Guide
2 TC58 Wireless Vehicle Charging Cradle
Zebra reserves the right to make changes to any product to
improve reliability, function, or design. Zebra does not
assume any product liability arising out of, or in connection
with, the application or use of any product, circuit, or
application described herein. No license is granted, either
expressly or by implication, estoppel, or otherwise under any
patent right or patent, covering or relating to any combination,
system, apparatus, machine, material, method, or process in
which our products might be used. An implied license exists
only for equipment, circuits, and subsystems contained in the
products.
Warranty
For the complete Zebra hardware product warranty
statement, go to zebra.com/warranty
.
Introduction
This guide describes how to install and use a
CRD-TC58-WCVC-01 Wireless Vehicle Cradle with a TC58
touch computers.
Install the cradle into a vehicle. Once installed, the cradle:
• Holds the TC58 securely in place
• Provides wireless power for operating the TC58.
Requirements
For mounting onto a RAM Mount®:
• RAM Mount (sold separately)
• Four M4 screws (included).
Installation Guide 3
Parts
Release Latch
FRONT VIEW
Mounting
Holes
REAR VIEW
4 TC58 Wireless Vehicle Charging Cradle
CAUTION: ROAD SAFETY - Do not use the TC58 while driving.
Park the vehicle first. Always ensure the TC58 is fully inserted
into the cradle. Do not place it on the seat or where it can break
loose in a collision or sudden stop. Lack of proper insertion may
result in property damage or personal injury. Zebra is not responsible for any loss resulting from the use of the products while driving. Remember: Safety comes first.
Mounting the Cradle to a RAM
Mount
To mount the cradle onto a diamond (RAM-B-238U) or round
(RAM-202U) shaped RAM Mount (RAM-B-166U):
CAUTION: Only mount the Vehicle Cradle in a vertical position.
Never mount the vehicle cradle on the side or upside down or on
a wall that can be subject to impact or collision of greater than
10Gs, in accordance with SAE J1455 Section 4.10.3.5.
1.
Follow the instructions that are provided with the RAM
Mount for RAM Mount mounting instructions.
2. Align the vehicle cradle with the RAM Mount ball base.
3. Secure the vehicle cradle to the ball base using M4
screws, lock washers and flat washers (provided).
CAUTION: Do not install a Vehicle Cradle on or near an air bag
cover plate or within an area that could cause personal injury. Also, do not install it in a location that affects vehicle safety or your
ability to drive.
4.
Secure the RAM Mount to the vehicle depending upon
the type of RAM Mount. See instructions provided with
RAM Mount.
Installation Guide 5
5. Tighten the screws to secure the cradle to the mounting
plate.
6. Adjust RAM Mount according to RAM Mount instructions.
Mounting to a Windshield
CAUTION: Do not install a vehicle cradle on or near an air bag
cover plate or within an area that could cause personal injury.
Do not install it in a location that inhibits visibility, affects vehicle
safety or drivability.
1.
Fix the RAM Mount to the selected area.
2. Twist the lever on the RAM Mount suction cup base to
create a vacuum between the suction cup and the
windshield.
CAUTION:
due to
1) Ensure the glass and the suction cup are completely clean and
free of oils and debris before installing.
2) Periodically remove, clean, and re-seat the suction cup on the
glass (more frequently in the summer and hot, sunny climates).
3.
Adjust the vehicle cradle in a vertical position and ensure
To prevent suction cups from falling off the windshield
bleeding air over time and with extreme heat:
that the suction bond is strong enough before installing
the device.
4. To connect power, see Power Connection on page 7.
5. To insert the device, see TC58 Insertion on page 8.
6 TC58 Wireless Vehicle Charging Cradle
Mounting to a Dashboard
CAUTION: Do not install a vehicle cradle on or near an air bag
cover plate or within an area that could cause personal injury.
Do not install it in a location that inhibits visibility, affects vehicle
safety or drivability.
1.
Fix the RAM Mount to the selected area.
NOTE: Ensure that the installed vehicle cradle does not rest on
other structures that can transmit the vehicle vibrations that
would normally be reduced by the suction cup.
Figure 1 Mounting to a Dashboard
2. Twist the lever on the RAM Mount suction cup base to
create a vacuum between the suction cup and the
dashboard.
3. Adjust the vehicle cradle in a vertical position and ensure
that the suction bond is strong enough before installing
the device.
4. To connect power, see Power Connection on page 7.
5. To insert the device, see TC58 Insertion on page 8.
Loading...