Zebra TC57 TC57 Touch Computer Quick Start Guide (en)

TC57
Touch Computer
Quick Start Guide
MN-003234-03 Rev. A

Copyright

ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2019 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to
www.zebra.com/copyright
TC57 Quick Start Guide
.
WARRANTY: For complete warranty information, go to www.zebra.com/warranty
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula

Terms of Use

Proprietary Statement

This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries (“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies.

Product Improvements

Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice.

Liability Disclaimer

Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.
.
.

Limitation of Liability

In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Provide Documentation Feedback

If you have comments, questions, or suggestions about this guide, send an email to
EVM-Techdocs@zebra.com
.
2

Features

PTT Button
Scan Button
Microphone
Interface Connector
Speaker
Touch Screen
Light Sensor
Charging/Notification LED
Proximity Sensor
Microphone
Data Capture LED
Receiver
Front Camera
ActiveEdge Touch Zone
ActiveEdge Touch Zone
Programmable
Button
Battery Release Latch
Battery Release Latch
Volume Up/Down Button
NFC Antenna
Camera Flash
Exit Window
Scan Button
Rear Camera
Power Button
Headphone Jack
Battery
Microphone
TC57 Quick Start Guide
3

Installing a microSD Card

The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack. Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.
CAUTION: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper ESD
precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
Lift the access door.
1.
TC57 Quick Start Guide
2. Slide the microSD card holder door to the Open position.
3. Lift the microSD card holder door.
4. Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each
side of the door.
4
TC57 Quick Start Guide
5. Close the microSD card holder door.
6. Slide the microSD card holder door to the Lock position.
CAUTION: Access door must be replaced and securely seated to ensure proper device sealing.
Re-install the access door.
7.
5

Installing the SIM Card

NOTE: Only use a nano SIM card. Not applicable to TC57JO.
CAUTION: For proper electrostatic discharge (ESD) precautions to avoid damaging the SIM card. Proper ESD precautions
include, but not limited to, working on an ESD mat and ensuring that the user is properly grounded.
Remove access cover.
1.
Figure 1 Remove Access Door
TC57 Quick Start Guide
2. Slide the SIM card holder to the unlock position.
Figure 2 Unlock SIM Card Holder
6
Loading...
+ 13 hidden pages