TC56/TC57
Vehicle Cradle
Installation Guide
TC56/TC57 Vehicle Cradle Installation Guide
Copyright
© 2018 ZIH Corp. and/or its affiliates. All rights reserved. ZEBRA and the
stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions
worldwide. All other trademarks are the property of their respective owners.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark
information, go to zebra.com/copyright
WARRANTY: For complete warranty information, go to zebra.com/warranty
END USER LICENSE AGREEMENT: For complete EULA information, go to
zebra.com/eula
.
.
.
Terms of Use
Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation
and its subsidiaries (“Zebra Technologies”). It is intended solely for the
information and use of parties operating and maintaining the equipment described
herein. Such proprietary information may not be used, reproduced, or disclosed to
any other parties for any other purpose without the express, written permission of
Zebra Technologies.
Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All
specifications and designs are subject to change without notice.
Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering
specifications and manuals are correct; however, errors do occur. Zebra
Technologies reserves the right to correct any such errors and disclaims liability
resulting therefrom.
Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation,
production, or delivery of the accompanying product (including hardware and
software) be liable for any damages whatsoever (including, without limitation,
consequential damages including loss of business profits, business interruption,
or loss of business information) arising out of the use of, the results of use of, or
inability to use such product, even if Zebra Technologies has been advised of the
2
TC56/TC57 Vehicle Cradle Installation Guide
possibility of such damages. Some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Warranty
For the complete Zebra hardware product warranty statement, go to:
zebra.com/warranty
.
Service Information
Before you use the unit, it must be configured to operate in your facility’s network
and run your applications.
If you have a problem using your equipment, contact your facility’s Technical or
Systems Support. If there is a problem with the equipment, they will contact the
Zebra Global Customer Support at zebra.com/support
For the latest version of this guide go to: zebra.com/support
.
.
Provide Documentation Feedback
If you have comments, questions, or suggestions about this guide, send an email
to EVM-Techdocs@zebra.com
.
Introduction
This guide describes how to install and use a CRD-TC56-CVCD2-02 vehicle
cradle with a TC56/TC57 touch computer.
Install the cradle into a vehicle. Once installed, the cradle:
• holds the TC56/TC57 securely in place
• provides power for operating the TC56/TC57 and re-charges the battery in the
TC56/TC57 when connected to the USB cable (CBL-TC5X-USBC2A-01) and
a cigarette lighter adapter (CHG-AUTO-USB1-01)
• provides communication when connected to the USB cable
(CBL-TC5X-USBC2A-01) and a laptop or desktop.
The cradle is powered by the vehicle’s 12V or 24V electrical system. The voltage
input range is 12V to 24V (3.5A). The voltage output is 5V (+/- 5%) (2.5A).
3
TC56/TC57 Vehicle Cradle Installation Guide
Release Latch
Release Latch
Mounting Holes
Cable Retainer
USB Power Port
Requirements
For mounting onto a twist-lock suction cup RAM Mount® (RAM-B-166U):
• RAM Mount (sold separately)
• Two M5 screws (included with RAM Mount).
Parts
Figure 1 Front View
Figure 2 Rear View
4
TC56/TC57 Vehicle Cradle Installation Guide
I/O Connector Pin-Outs
Figure 3 Inside View
CAUTION: ROAD SAFETY - Do not operate the TC56/TC57 while the vehicle is in mo tio n.
Park the vehicle first. Always ensure the TC56/TC57 is fully inserted into the cradle. Do
not place it on the seat or where it can break loose in a collision or sudden stop. Lack of
proper insertion may result in property damage or personal injury. Zebra is not responsible for any loss resulting from the use of the products while driving. Remember: Safety
comes first.
Mounting the Vehicle Cradle to a RAM
Mount
To mount the vehicle cradle to a RAM Mount:
CAUTION: Only mount the vehicle cradle in a vertical position. Never mount the vehicle
cradle on the side or upside down or on a wall that can be subject to impact or collision
of greater than 10Gs, in accordance with SAE J1455 Section 4.10.3.5.
Follow the instructions that are provided with the RAM Mount for RAM Mount
1.
mounting instructions.
2. Align the back of the vehicle cradle with the RAM Mount diamond plate.
5
TC56/TC57 Vehicle Cradle Installation Guide
RAM Mount
TC56/TC57 Vehicle Cradle
Lever
3. Attach and secure the vehicle cradle to the diamond plate using two M5
screws.
Figure 4 Attach and Secure Vehicle Cradle to the RAM Mount
4. Secure the RAM Mount to the vehicle depending upon the type of RAM
Mount. See instructions provided with the RAM Mount.
5. Adjust the RAM Mount according to the RAM Mount instructions.
6
TC56/TC57 Vehicle Cradle Installation Guide
Mounting to a Windshield
CAUTION: Do not install a vehicle cradle on or near an air bag cover plate or within an
aerobic zone. Also, do not install it in a location that affects vehicle safety or drivability.
Fix the RAM Mount to the selected area.
1.
Figure 5 Mounting to a Windshield
2. Twist the lever on the RAM Mount suction cup base to create a vacuum
between the suction cup and the windshield.
CAUTION:
time and with extreme heat:
1) Ensure the glass and the suction cup are completely clean and free of oils and debris
before installing.
2) Periodically remove, clean, and re-seat the suction cup on the glass (more frequently
in the summer and hot, sunny climates).
Adjust the vehicle cradle in a vertical position and ensure that the suction
3.
To prevent suction cups from falling off the windshield due to
bleeding air over
bond is strong enough before installing the device.
4. To connect power, see Connecting Power on page 9.
5. To insert the device, see Inserting and Removing the TC56/TC57 on page 13.
7
TC56/TC57 Vehicle Cradle Installation Guide
Mounting to a Dashboard
CAUTION: Do not install a vehicle cradle on or near an air bag cover plate or within an
aerobic zone. Also, do not install it in a location that affects vehicle safety or drivability.
Fix the RAM Mount to the selected area.
1.
NOTE: Ensure that the installed vehicle cradle does not rest on the dashboard
or other structure that can transmit the vehicle vibrations that would normally
be reduced by the suction cup.
Figure 6 Mounting to a Dashboard
2. Twist the lever on the RAM Mount suction cup base to create a vacuum
between the suction cup and the dashboard.
3. Adjust the vehicle cradle in a vertical position and ensure that the suction
bond is strong enough before installing the device.
4. To connect power, see Connecting Power on page 9.
5. To insert the device, see Inserting and Removing the TC56/TC57 on page 13.
8
Loading...