COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to www.zebra.com/
copyright.
WARRANTY: For complete warranty information, go to www.zebra.com/warranty
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula
Terms of Use
•Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and
maintaining the equipment described herein. Such proprietary information may not be used, reproduced,
or disclosed to any other parties for any other purpose without the express, written permission of Zebra
Technologies.
•Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are
subject to change without notice.
•Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are
correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and
disclaims liability resulting therefrom.
•Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the
accompanying product (including hardware and software) be liable for any damages whatsoever
(including, without limitation, consequential damages including loss of business profits, business
interruption, or loss of business information) arising out of the use of, the results of use of, or inability to
use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some
jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
.
.
Revision History
Changes to the original guide are listed below:
ChangeDateDescription
-01 Rev A10/2017Initial release.
-02 Rev. A12/2017Removed 4-way charging in accessory section.
-03 Rev. A8/2018Updated cleaning instructions.
2
ChangeDateDescription
-04 Rev. A9/2019Removed Imager as Camera section from DataWedge chapter. Added healthcare
cleaning link to zebra.com page.
-05 Rev. A12/2019Updated battery information in Charging the Battery section.
3
Table of Contents
Terms of Use .................................................................................................................................... 2
Revision History ................................................................................................................................ 2
Table of Contents................................................................................................................................... 4
This guide provides information about using the TC51 touch computer and accessories. The TC51 refers to both
the TC51 (Standard) and TC51-HC (Healthcare) configurations, except where noted.
NOTE: Screens and windows pictured in this guide are samples and can differ from actual screens.
Documentation Set
The documentation set for the TC51 provides information for specific user needs, and includes:
•TC51 Touch Computer Quick Start Guide - describes how to get the TC51 up and running.
•TC51 Touch Computer User Guide for Android Version 7.1.2 - describes how to use the TC51.
•TC51 Touch Computer Integrator Guide for Android Version 7.1.2 - describes how to set up the TC51 and
accessories.
Configurations
This guide covers the following configurations:
ConfigurationRadiosDisplayMemory
TC510K-1WLAN: 802.11
TC510K-2WLAN: 802.11
a/b/g/n/d/h/i/k/r
WPAN:
Bluetooth v4.1
Low Energy
a/b/g/n/d/h/i/k/r
WPAN:
Bluetooth v4.1
Low Energy
5.0” High
Definition (1280
x 720) LCD
5.0” High
Definition (1280
x 720) LCD
12
2 GB RAM / 16
GB Flash or 4
GB RAM / 32
GB Flash
2 GB RAM / 16
GB Flash or 4
GB RAM / 32
GB Flash
Data Capture
Options
2D imager
(SE-4710) and
integrated NFC
2D imager
(SE-4710) and
integrated NFC
Operating
System
Android-based,
Google ™
Mobile Services
(GMS) 7.1.2.
Android-based,
Android
Open-Source
Project 7.1.2
Software Versions
To determine the current software versions touch > About phone.
•Model number- Displays the model number.
•Android version - Displays the operating system version.
•Kernel version - Displays the kernel version number.
•Build number - Displays the software build number.
To determine the device serial number touch > About phone > Status.
•Serial number - Displays the serial number.
Chapter Descriptions
Topics covered in this guide are as follows:
•Getting Started provides information on getting the TC51 up and running for the first time.
•Accessories describes the available accessories and how to use them with the TC51.
•DataWedge describes how to use and configure the DataWedge application.
•USB Communication describes how to connect the TC51 to a host computer and transfer files.
•Settings provides the settings for configuring the TC51.
•Application Deployment provides information for developing and managing applications.
•Maintenance and Troubleshooting includes instructions on cleaning and storing the TC51, and provides
troubleshooting solutions for potential problems during TC51 operation.
•Technical Specifications provides the technical specifications for the TC51.
About This Guide
Notational Conventions
The following conventions are used in this document:
•Bold text is used to highlight the following:
•Dialog box, window and screen names
•Drop-down list and list box names
•Check box and radio button names
•Icons on a screen
•Key names on a keypad
•Button names on a screen.
•Bullets (•) indicate:
•Action items
•Lists of alternatives
•Lists of required steps that are not necessarily sequential.
•Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
•TC51 Touch Computer User Guide for Android Version 7.1.2, p/n MN-002868-xx.
About This Guide
For the latest version of this guide and all guides, go to: www.zebra.com/support
Service Information
If you have a problem with your equipment, contact Zebra Global Customer Support for your region. Contact
information is available at: www.zebra.com/support
When contacting support, please have the following information available:
•Serial number of the unit (found on manufacturing label)
•Model number or product name (found on manufacturing label)
•Software type and version number
.
.
Zebra responds to calls by email, telephone or fax within the time limits set forth in support agreements.
If your problem cannot be solved by Zebra Customer Support, you may need to return your equipment for servicing
and will be given specific directions. Zebra is not responsible for any damages incurred during shipment if the
approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your Zebra business product from a Zebra business partner, contact that business partner for
support.
Provide Documentation Feedback
If you have comments, questions, or suggestions about this guide, send an email to EVM-Techdocs@zebra.com.
14
Getting Started
Introduction
This chapter provides information for getting the device up and running for the first time.
Setup
Perform this procedure to start using the TC51 for the first time.
1.Install a micro secure digital (SD) card (optional).
2.Install the battery.
3.Charge the TC51.
4.Power on the TC51.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack. Refer to
the documentation provided with the card for more information, and follow the manufacturer’s recommendations for
use.
CAUTION:Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper
ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator
is properly grounded.
1.Lift the access door.
15
Getting Started
Figure 1 Lift Access Door
2.Slide the microSD card holder to the unlock position.
Figure 2 Unlock microSD Card Holder
3.Lift the microSD card holder.
Figure 3 Lift the microSD Card Holder
4.Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each
side of the door.
16
Getting Started
Figure 4 Insert microSD Card in Holder
5.Close the microSD card holder and slide into the lock position.
Figure 5 Re-install Access Door
CAUTION:Access door must be replaced and securely seated to ensure proper device sealing.
6.Re-install the access door.
Figure 6 Replace Access Door
17
Getting Started
Installing the Battery
1.Insert the battery, bottom first, into the battery compartment in the back of the TC51.
Figure 7 Insert Bottom of Battery into Battery Compartment
2.Press the battery down into the battery compartment until the battery release latches snap into place.
Charging the Battery
Before using the TC51 for the first time, charge the main battery until the green Charging/Notification light emitting
diode (LED) remains lit. To charge the TC51 use a cable or a cradle with the appropriate power supply. For
information about the accessories available for the TC51 see Accessories for more information.
The >
15.48 Watt hours (typical) / > 4,150 mAh battery, charges from fully depleted to 90% in approximately 2.5
hours, and from fully depleted to 100% in approximately three hours.
NOTE: In many cases the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for
approximately 14 hours of use.
To achieve the best fast charging results use only Zebra charging accessories and batteries. Charge
batteries at room temperature with the TC51 in sleep mode.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The TC51 or accessory always performs
battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the
TC51 or accessory may for small periods of time alternately enable and disable battery charging to keep the
battery at acceptable temperatures. The TC51 or accessory indicates when charging is disabled due to abnormal
temperatures via its LED and a notification appears on the display.
1.To charge the main battery, connect the charging accessory to the appropriate power source.
2.Insert the TC51 into a cradle or attach to a cable. The TC51 turns on and begins charging. The
Charging/Notification LED blinks amber while charging, then turns solid green when fully charged.
18
Getting Started
Charging Indicators
Table 1 Charging/Notification LED Charging Indicators
StateLEDIndication
OffTC51 is not charging. TC51 is not inserted correctly in the
cradle or connected to a power source. Charger/cradle is
not powered.
Slow Blinking Amber (1 blink every 4
seconds)
Slow Blinking Red (1 blink every 4
seconds)
Solid GreenCharging complete.
Solid RedCharging complete but the battery is at end of useful life.
Fast Blinking Amber (2 blinks/second)Charging error, e.g.:
Fast Blinking Red (2 blinks/second)Charging error but the battery is at end of useful life., e.g.:
Replacing the Battery
TC51 is charging.
TC51 is charging but the battery is at end of useful life.
•Temperature is too low or too high.
•Charging has gone on too long without completion
(typically eight hours).
•Temperature is too low or too high.
•Charging has gone on too long without completion
(typically eight hours).
CAUTION:Do not add or remove microSD card during battery replacement.
1.Press the Power button until the menu appears.
2.Touch Battery Swap.
3.Follow the on-screen instructions.
4.Wait for the LED to turn off.
5.If hand strap is attached, remove hand strap.
6.Press the two battery latches in.
19
Figure 8 Press Battery Latches
7.Lift the battery from the TC51.
Getting Started
Figure 9 Lift the Battery
CAUTION:Replace the battery within two minutes. After two minutes the device reboots and data may be lost.
8.Insert the replacement battery, bottom first, into the battery compartment in the back of the TC51.
9.Press the battery down until the battery release latches snap into place.
10. Replace the hand strap, if required.
11. Press the Power button to turn on the TC51.
20
Replacing the microSD Card
To replace the microSD card:
1.Press the Power button until the menu appears.
2.Touch Power off.
3.Touch OK.
4.If hand strap is attached, slide the hand strap clip up toward the top of the TC51 and then lift.
5.Press the two battery latches in.
6.Lift the battery from the TC51.
7.Lift the access door.
Figure 10 Remove Access Door
Getting Started
8.Remove microSD card from holder.
9.Insert the replacement microSD card.
CAUTION:Access door must be replaced and securely seated to ensure proper device sealing.
10. Replace the access door.
Figure 11 Replace Access Door
11. Insert the battery, bottom first, into the battery compartment in the back of the TC51.
12. Press the battery down until the battery release latches snap into place.
21
13. Replace the hand strap, if required.
14. Press and hold the Power button to turn on the TC51.
Resetting the TC51
There are four reset functions:
•Soft reset
•Hard reset
•Enterprise reset. See Performing an Enterprise Reset on page 154.
•Factory reset See Performing a Factory Reset on page 156.
Performing a Soft Reset
Perform a soft reset if applications stop responding.
1.Press and hold the Power button until the menu appears.
2.Touch Reboot and then select OK.
3.The device reboots.
Getting Started
Performing a Hard Reset
CAUTION:Performing a hard reset with a SD card installed in the TC51 may cause damage or data corruption to
the SD card.
Perform a hard reset if the TC51 stops responding.
1.Simultaneously press the Power, PTT button and Volume Up buttons for at least four seconds.
2.When the screen turns off, release the buttons.
3.The device reboots.
22
Accessories
Introduction
This chapter provides information for using the accessories for the device.
Accessories
This table lists the accessories available for the TC51.
Table 2 TC51 Accessories
AccessoryPart NumberDescription
Cradles
1-Slot USB/Charge Only
Cradle Kit
4-Slot Charge Only Cradle
with Battery Charger Kit
5-Slot Charge Only Cradle
Kit
5-Slot Ethernet Cradle KitCRD-TC51-5SETH-01Provides device charging and provides Ethernet
Cradle MountBRKT-SCRD-SMRK-01Mounts the 5-Slot Charge Only Cradle, 5-Slot
Batteries and Chargers
PowerPrecisionPlus batteryBTRY-TC51-43MA1-01
4-Slot Battery Charger KitSAC-TC51-4SCHG-01Charges up to four battery packs. Includes
CRD-TC51-1SCU-01Provides device charging and communication.
Includes cradle, power supply,
(PWR-BGA12V50W0WW) and DC line cord.
CRD-TC51-5SC4B-01Charges up to four devices and four spare
batteries. Includes, cradle, power supply,
(PWR-BGA12V108W0WW) and DC line cord.
CRD-TC51-5SCHG-01Charges up to five devices. Includes, cradle,
power supply, (PWR-BGA12V108W0WW) and
DC line cord.
communication for up to five devices. Includes
cradle, power supply, and DC line cord.
Ethernet Cradle, and 4-Slot Battery Charger to a
wall or rack.
Replacement battery (single pack).
BTRY-TC51-43MA1-10
Replacement battery (10–pack).
cradle, power supply and DC line cord
23
Table 2 TC51 Accessories (Continued)
AccessoryPart NumberDescription
Vehicle Solutions
Accessories
Cigarette Light Adapter
Auto Charge Cable
Charge and Communication Cables
Rugged Charge/USB CableCBL-TC51-USB1-01Provides communication and power to the
Audio Accessories
2.5 mm Audio AdapterCBL-TC51-HDST25-01Plugs into the device and provides audio to a
2.5 mm HeadsetHDST-25MM-PTVP-01Use for PTT and VoIP calls
3.5 mm Audio AdapterCBL-TC51-HDST35-01Plugs into the device and provides audio to a
3.5 mm HeadsetHDST-35MM-PTVP-01Use for PTT and VoIP calls.
Miscellaneous
Rugged BootSG-TC51-EXO1-01Provides additional protection for the device.
Trigger HandleTRG-TC51-SNP1-01Adds gun-style handle with a scanner trigger for
CHG-AUTO-USB1-01Provides power to the device from a cigarette
lighter socket.
device. Use with power supply, p/n
PWRS-14000-249R, sold separately.
wired headset with 2.5 mm plug.
wired headset with collared 3.5 mm plug.
Requires power supply PWR-WUA5V12W0xx.
comfortable and productive scanning. Requires
Rugged Boot.
Soft HolsterSG-TC51-HLSTR1-01Use to hold the device on hip. Accepts device
Hand StrapSG-TC51-EHDSTP1-03Replacement hand strap with hand strap
Basic Hand StrapSG-TC51-BHDSTP1-03Provide a hand strap to assist in holding the
Stylus and Coiled TetherSG-TC7X-STYLUS-03Stylus with coiled tether (3-pack).
Power Supplies
Power SupplyPWR-BGA12V50W0WWProvides power to the 1-Slot USB Charge cradle
TRG-TC51-TRG1-01Adds gun-style handle with a scanner trigger for
comfortable and productive scanning.
with Rugged Boot and Trigger Handle
mounting clip (3–pack).
TC51 without a Rugged Boot.
and 4-Slot Spare Battery Charger. Requires AC
line cord.
24
Accessories
Table 2 TC51 Accessories (Continued)
AccessoryPart NumberDescription
Power SupplyPWR-BGA12V108W0WWProvides power to the 4-Slot Charge Only
Cradle with battery Charger, 5-Slot Charge Only
cradle and the 5-Slot Ethernet Cradle. Requires
DC Line Cord, p/n 50–16002–029R and country
specific three wire grounded AC line cord sold
separately.
Power SupplyPWR-WUA5V12W0USProvides 12 VDC, 2.5 A power to the Rugged
Charge/USB cable. Includes plug adapter for
use in United States.
Power SupplyPWR-WUA5V12W0GBProvides 12 VDC, 2.5 A power to the Rugged
Charge/USB cable. Includes plug adapter for
use in the European Union.
Power SupplyPWR-WUA5V12W0EUProvides 12 VDC, 2.5 A power to the Rugged
Charge/USB cable. Includes plug adapter for
use in United Kingdom.
Power SupplyPWR-WUA5V12W0AUProvides 12 VDC, 2.5 A power to the Rugged
Charge/USB cable. Includes plug adapter for
use in Australia.
Power SupplyPWR-WUA5V12W0CNProvides 12 VDC, 2.5 A power to the Rugged
Charge/USB cable. Includes plug adapter for
use in China.
Power SupplyPWR-WUA5V12W0INProvides 12 VDC, 2.5 A power to the Rugged
Charge/USB cable. Includes plug adapter for
use in India.
DC Line Cord
DC Line CordCBL-DC-388A1-01Provides power from the power supply
2-way DC CableCBL-DC-523A1-01Connects one power supply
CBL-DC-382A1-01
Provides power from the power supply
(PWR-BGA12V108W0WW) to the 4-Slot
Charge Only Cradle with Battery Charger, 5-Slot
Charge Only Cradle and 5-Slot Ethernet Cradle.
(PWR-BGA12V50W0WW) to the 1-Slot
USB/Charge Only Cradle and 4-Slot Battery
Charger.
(PWR-BGA12V108W0WW) to two 4-Slot
Battery Chargers.
25
1-Slot USB Charge Cradle
CAUTION:Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page
170.
The 1-Slot USB Charge Cradle:
•Provides 5 VDC power for operating the device.
•Charges the device’s battery.
•Provides USB communication with host computer.
Figure 12 1–Slot USB Charge Cradle Setup
Accessories
AC Line Cord
Power Supply
DC Line Cord
Charging the Device
To charge a device:
NOTE: If the device has a Rugged Boot, remove the cup insert before inserting the device. See Inserting a
TC51 with Rugged Boot into Cradle on page 27.
USB Cable
26
Accessories
1.Insert the device into the slot to begin charging.
Figure 13 Battery Charging
Power LED
2.Ensure the device is seated properly.
Inserting a TC51 with Rugged Boot into Cradle
Each cradle cup has an insert that must be removed prior to inserting the TC51 with Rugged Boot. Remove the
insert and then insert the TC51 into the cup.
Figure 14 Remove Insert from Cup
27
Accessories
Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device. See Table 1 on
page 19 for device charging status. The >
depleted to 90% in approximately 2.5 hours and from fully depleted to 100% in approximately three hours.
NOTE: In many cases the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for
approximately 14 hours of use.
To achieve the best fast charging results use only Zebra charging accessories and batteries. Charge
batteries at room temperature with the TC51 in sleep mode.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery
charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or
cradle may for small periods of time alternately enable and disable battery charging to keep the battery at
acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal
temperatures via its LED.
15.48 Watt hours (typical) / > 4,150 mAh battery charges from fully
28
Accessories
4-Slot Charge Only Cradle with Battery Charger
CAUTION:Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page
170.
The 4-Slot Charge Only Cradle with Battery Charger:
•Provides 5 VDC power for operating the TC51.
•Simultaneously charges up to four TC51s and up to four spare batteries using the Battery Charger
Adapter.
Figure 15 4-Slot Charge Only Cradle with Battery Charger Setup
Power Supply
AC Line Cord
Charging the TC51
To charge a device:
NOTE: If the device has a Rugged Boot, remove the cup insert before inserting the device. See Inserting a
TC51 with Rugged Boot into Cradle on page 31.
DC Line Cord
29
Accessories
1.Insert the TC51 into a slot to begin charging.
Figure 16 TC51 Battery Charging
Figure 17 Spare Battery Charging
Power LED
30
Loading...
+ 173 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.