Page 1
TC25
Rugged Smartphone
User Guide
for Android ™ 7.1.2 Nougat
MN-003051-04 Rev. A
Page 2
Copyright
© 2018 ZIH Corp. and/or its affiliates. All rights reserved. ZEBRA and the stylized Zebra head are trademarks of
ZIH Corp., registered in many jurisdictions worldwide. Google, Google Play and other marks are trademarks of
Google Inc. All other trademarks are the property of their respective owners.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to www.zebra.com/copyright.
WARRANTY: For complete warranty information, go to www.zebra.com/warranty.
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula.
Terms of Use
• Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and
maintaining the equipment described herein. Such proprietary information may not be used, reproduced,
or disclosed to any other parties for any other purpose without the express, written permission of Zebra
Technologies.
• Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are
subject to change without notice.
• Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are
correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and
disclaims liability resulting therefrom.
• Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the
accompanying product (including hardware and software) be liable for any damages whatsoever
(including, without limitation, consequential damages including loss of business profits, business
interruption, or loss of business information) arising out of the use of, the results of use of, or inability to
use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some
jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Revision History
Changes to the original guide are listed below:
Change Date Description
-01 Rev A 9/2017 Initial Release
-02 Rev A 1/2018 Add note about SIM card thickness (page 17). Add note that Indonesian
-03 Rev A 2/2018 Maintenance release updates for BSP 04-14-XX.
-04 Rev. A 9/2018 Correct WLAN Security and Encryption information on page 162.
configurations do not support LTE.
2
Page 3
Table of Contents
Copyright ........................................................................................................................................... 2
Terms of Use .................................................................................................................................... 2
Revision History ................................................................................................................................ 2
Table of Contents................................................................................................................................... 3
About This Guide
Configurations ................................................................................................................................. 10
Chapter Descriptions ...................................................................................................................... 10
Notational Conventions ................................................................................................................... 11
Related Documents and Software .................................................................................................. 11
Service Information ......................................................................................................................... 11
Provide Documentation Feedback .................................................................................................. 12
Getting Started
Unpacking ....................................................................................................................................... 13
Features .......................................................................................................................................... 14
Setup ............................................................................................................................................... 16
Installing a microSD Card ......................................................................................................... 16
Installing the SIM Card .............................................................................................................. 18
Charging the Battery ................................................................................................................. 19
Charging Indicators ................................................................................................................... 21
Google Account Setup .............................................................................................................. 22
Zebra Visibility Services ............................................................................................................ 22
Replacing the microSD Card .......................................................................................................... 22
Replacing the SIM Card .................................................................................................................. 24
Accessing Device Settings .............................................................................................................. 26
Battery Management ....................................................................................................................... 26
Monitor Battery Usage .............................................................................................................. 26
Low Battery Notification ............................................................................................................ 27
Battery Optimization .................................................................................................................. 27
Turning Off the Radios ........................................................................................................ 28
Setting the Date and Time .............................................................................................................. 28
Display Setting ................................................................................................................................ 28
Setting the Screen Brightness ................................................................................................... 28
3
Page 4
Table of Contents
Setting Screen Rotation ............................................................................................................ 29
Setting Screen Timeout Setting ................................................................................................ 29
Setting Font Size ....................................................................................................................... 29
Setting the Charge LED ............................................................................................................ 30
Setting the Charge LED ............................................................................................................ 30
General Sound Setting .................................................................................................................... 31
Wake-Up Sources ........................................................................................................................... 32
Using the TC25
Google Mobile Services .................................................................................................................. 34
Home Screen .................................................................................................................................. 34
Setting Home Screen Rotation .................................................................................................. 35
Status Bar ................................................................................................................................. 36
Status Icons ........................................................................................................................ 36
Notification Icons ................................................................................................................. 38
Managing Notifications .............................................................................................................. 38
Setting Application Notifications .......................................................................................... 39
Viewing Notification Settings for All Apps ........................................................................... 39
Controlling Lock Screen Notifications ................................................................................. 39
Quick Settings ........................................................................................................................... 40
Edit Icons on Quick Settings ............................................................................................... 41
Application Shortcuts and Widgets ........................................................................................... 41
Adding an Application to the Home Screen ........................................................................ 41
Adding a Widget to the Home Screen ................................................................................. 41
Moving Items on the Home Screen ..................................................................................... 42
Removing an Application Shortcut or Widget from the Home Screen ................................ 42
Folders ...................................................................................................................................... 42
Creating a Folder ................................................................................................................ 42
Naming Folders ................................................................................................................... 42
Removing a Folder .............................................................................................................. 42
Home Screen Wallpaper ........................................................................................................... 43
Using the Touchscreen ................................................................................................................... 43
On-Screen Keyboards .................................................................................................................... 43
Editing Text ......................................................................................................................... 43
Entering Numbers, Symbols and Special Characters ......................................................... 44
Switching Language Keyboards ................................................................................................ 44
Configuring the Keyboard ......................................................................................................... 44
GMS Keyboard .................................................................................................................... 44
Do Not Disturb Feature ................................................................................................................... 45
Limit Sounds and Vibrations ..................................................................................................... 45
Alarms Only ......................................................................................................................... 45
Priority Notifications Only .................................................................................................... 46
Automatically Block Sounds and Vibrations .................................................................................... 46
Silence Sounds During Certain Times ...................................................................................... 46
Silence Sounds During Events and Meetings ........................................................................... 47
Turn Sounds Back On ............................................................................................................... 47
Override Do Not Disturb for Specific Apps ................................................................................ 47
Applications ..................................................................................................................................... 48
Accessing Applications ............................................................................................................. 50
Switching Between Recent Applications ................................................................................... 51
4
Page 5
Table of Contents
Un-Locking the Screen ................................................................................................................... 51
Scheduled Power On and Off ......................................................................................................... 52
Resetting the Device ....................................................................................................................... 54
Performing a Soft Reset ............................................................................................................ 54
Performing a Hard Reset .......................................................................................................... 54
Suspend Mode ................................................................................................................................ 54
Transferring Files with a Host Computer via USB .......................................................................... 55
Transferring Files using Media Transfer Protocol ..................................................................... 55
Transferring Files using Photo Transfer Protocol ...................................................................... 55
Disconnect from the Host Computer ......................................................................................... 56
Calls
Emergency Calling .......................................................................................................................... 57
Audio Modes ................................................................................................................................... 57
Using a Bluetooth Headset ............................................................................................................. 57
Adjusting Audio Volume .................................................................................................................. 57
Making a Call Using the Dialer ........................................................................................................ 58
Dialer Dialing Options ............................................................................................................... 60
Making a Call Using Contacts ......................................................................................................... 60
Using the Dialer ......................................................................................................................... 60
Using the Contacts Application ................................................................................................. 61
Making a Call Using Call History ..................................................................................................... 61
Making a Conference Call ............................................................................................................... 62
Making a Call Using a Bluetooth Headset ...................................................................................... 64
Answering Calls .............................................................................................................................. 64
Call Settings .................................................................................................................................... 65
Display Options ......................................................................................................................... 65
Sounds and Vibrations .............................................................................................................. 65
Quick Responses ...................................................................................................................... 66
Speed Dial Settings ................................................................................................................... 66
Calls .......................................................................................................................................... 66
Call Blocking ............................................................................................................................. 66
Accessibility ............................................................................................................................... 67
Applications
File Browser .................................................................................................................................... 68
Messaging ....................................................................................................................................... 70
Sending a Text Message .......................................................................................................
Sending a Multimedia Message ................................................................................................ 70
Contacts .......................................................................................................................................... 72
Adding a Contact ....................................................................................................................... 72
Editing Contacts ........................................................................................................................ 72
Deleting Contacts ...................................................................................................................... 72
Camera ........................................................................................................................................... 74
Taking Photos ........................................................................................................................... 74
Taking a Panoramic Photo ........................................................................................................ 75
Recording Videos ...................................................................................................................... 75
Photo Settings ........................................................................................................................... 76
Video Settings ........................................................................................................................... 77
5
... 70
Page 6
Table of Contents
Photos ............................................................................................................................................. 79
Working with Albums ................................................................................................................. 80
Deleting an Album ............................................................................................................... 80
Working with Photos ................................................................................................................. 81
Viewing and Browsing Photos ............................................................................................. 81
Cropping a Photo ................................................................................................................ 81
Setting a Photo as a Contact Icon ....................................................................................... 82
Share a Photo ..................................................................................................................... 82
Deleting a Photo .................................................................................................................. 82
Working with Videos .................................................................................................................. 83
Watching Videos ................................................................................................................. 83
Sharing a Video ................................................................................................................... 83
Deleting a Video .................................................................................................................. 83
DataWedge Demonstration ............................................................................................................. 84
Sound Recorder .............................................................................................................................. 86
PTT Express Voice Client ............................................................................................................... 87
PTT Audible Indicators .............................................................................................................. 87
Notification Icons ....................................................................................................................... 88
Enabling PTT Communication .................................................................................................. 88
Selecting a Talk Group .............................................................................................................. 89
PTT Communication ................................................................................................................. 89
Creating a Group Call ......................................................................................................... 89
Responding with a Private Response ................................................................................. 89
Disabling PTT Express Voice Client Communication ............................................................... 89
RxLogger ........................................................................................................................................ 91
Enabling Logging ...................................................................................................................... 91
Disabling Logging ...................................................................................................................... 91
RxLogger Utility ............................................................................................................................... 92
Diagnostic Tool ............................................................................................................................... 93
Settings ............................................................................................................................... 95
Battery Test Information ...................................................................................................... 95
GPS Test Information .......................................................................................................... 95
System Test Information ..................................................................................................... 96
WLAN Test Information ....................................................................................................... 96
WWAN Test Information ..................................................................................................... 96
Bluetooth Test Information .................................................................................................. 96
Data Capture
Imaging ........................................................................................................................................... 97
Operational Modes .................................................................................................................... 97
RS507 Hands-Free Imager ............................................................................................................. 98
RS6000 Bluetooth Ring Scanner .................................................................................................... 98
Scanning Considerations ................................................................................................................ 99
Barcode Scanning with Internal SE2100 Imager ............................................................................ 99
SE2100 Picklist Mode ....................................................................................................... 100
SE2100 Basic MultiBarcode Mode .................................................................................... 101
Barcode Scanning with Internal SE4710 Imager .......................................................................... 102
SE4710 Basic MultiBarcode Mode .................................................................................... 103
Barcode Capture with RS6000 Bluetooth Ring Scanner .............................................................. 104
Barcode Capture with RS507 Hands-Free Imager ....................................................................... 105
6
Page 7
Table of Contents
Pairing the Bluetooth Imager ........................................................................................................ 107
Pairing Using Simple Serial Interface ...................................................................................... 107
Pairing Using Bluetooth Human Interface Device ................................................................... 107
DataWedge ................................................................................................................................... 108
Enabling DataWedge .............................................................................................................. 108
Disabling DataWedge ............................................................................................................. 108
Wireless
Wireless Wide Area Networks ...................................................................................................... 109
Sharing the Mobile Data Connection ...................................................................................... 109
USB Tethering ................................................................................................................... 109
Bluetooth Tethering ........................................................................................................... 110
Portable Wi-Fi Hotspot ...................................................................................................... 110
Cellular Network Settings ........................................................................................................ 111
Disabling Data When Roaming ......................................................................................... 111
Enhanced 4G LTE Mode ................................................................................................... 111
Search for MicroCell .......................................................................................................... 112
Editing the Access Point Name ......................................................................................... 112
Locking the SIM Card .............................................................................................................. 112
Data Usage ............................................................................................................................. 113
Set Data Usage Warning .................................................................................................. 114
Set Data Limit .................................................................................................................... 114
Wireless Local Area Networks ...................................................................................................... 114
Scan and Connect to a Wi-Fi Network .................................................................................... 115
Remove a Wi-Fi Network ........................................................................................................ 116
Bluetooth ....................................................................................................................................... 116
Adaptive Frequency Hopping .................................................................................................. 117
Security ................................................................................................................................... 117
Bluetooth Profiles .................................................................................................................... 117
Bluetooth Power States ........................................................................................................... 118
Bluetooth Radio Power ........................................................................................................... 118
Enabling Bluetooth ............................................................................................................ 119
Disabling Bluetooth ........................................................................................................... 119
Discovering Bluetooth Device(s) ............................................................................................. 119
Changing the Bluetooth Name ................................................................................................ 119
Connecting to a Bluetooth Device ........................................................................................... 120
Selecting Profiles on the Bluetooth Device ............................................................................. 120
Unpairing a Bluetooth Device .................................................................................................. 120
Accessories
Accessories ................................................................................................................................... 121
1-Slot Base Charge Only Cradle ................................................................................................... 124
Charging the Device ................................................................................................................ 124
Battery Charging ..................................................................................................................... 125
Charging Temperature ...................................................................................................... 125
1-Slot Ethernet Charge Cradle ...................................................................................................... 126
USB/Ethernet Communication ................................................................................................ 126
Ethernet LED Indicators .................................................................................................... 127
Establishing Ethernet Connection ..................................................................................... 128
7
Page 8
Table of Contents
Charging the Device ................................................................................................................ 128
Battery Charging ..................................................................................................................... 128
Charging Temperature ...................................................................................................... 129
5-Slot Charge Only Cradle ............................................................................................................ 130
Charging the TC25 .................................................................................................................. 130
Battery Charging ..................................................................................................................... 131
Charging Temperature ...................................................................................................... 131
Extended Power Pack ................................................................................................................... 132
Installation ............................................................................................................................... 132
Charging .................................................................................................................................. 132
Power Pack Charging ............................................................................................................. 134
Charging Temperature ...................................................................................................... 135
Check Power Level ................................................................................................................. 135
Resetting the Extended Power Pack ....................................................................................... 136
Trigger Handle .............................................................................................................................. 137
Installing the Optional Lanyard ................................................................................................ 137
Inserting the Device into the Trigger Handle ........................................................................... 138
Removing the Device from the Trigger Handle ....................................................................... 139
Wrist/Arm Mount ........................................................................................................................... 141
Wrist/Arm Mount Installation ................................................................................................... 141
Device Installation ................................................................................................................... 142
Device Removal ...................................................................................................................... 144
Scanning ................................................................................................................................. 144
Strap Installation ..................................................................................................................... 145
Hand Strap .................................................................................................................................... 147
Soft Holster ................................................................................................................................... 150
Adjusting the Holster ............................................................................................................... 150
Maintenance and Troubleshooting
Maintaining the TC25 .................................................................................................................... 153
Display Best Practices .................................................................................................................. 154
Image Retention ...................................................................................................................... 154
Battery Safety Guidelines ............................................................................................................. 154
Cleaning Instructions .................................................................................................................... 155
Approved Cleanser Active Ingredients .................................................................................... 155
Harmful Ingredients ................................................................................................................. 155
Cleaning Instructions ........................................................................................................
Special Cleaning Notes ........................................................................................................... 155
Cleaning Materials Required ................................................................................................... 155
Cleaning Frequency ................................................................................................................ 156
Cleaning the TC25 ........................................................................................................................ 156
Housing ................................................................................................................................... 156
Display .................................................................................................................................... 156
Camera and Exit Window ........................................................................................................ 156
Connector Cleaning ...................................................................................................................... 156
Cleaning Cradle Connectors ......................................................................................................... 156
Troubleshooting ............................................................................................................................ 158
TC25 ....................................................................................................................................... 158
....... 155
8
Page 9
Table of Contents
Technical Specifications
TC25 ............................................................................................................................................. 161
Index
9
Page 10
About This Guide
This guide provides information about using the TC25 Rugged Smartphone and accessories.
NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.
This guide applies to model numbers: TC25AJ, TC25BJ, and TC25CJ.
Configurations
This guide covers the following configurations:
Table 1 Configurations
Configuration
TC25AJ-10B101xx WAN/LAN/PAN GMS 2 GB/16 GB SE2100 Yes Blank
TC25AJ-10C102xx WAN/LAN/PAN GMS 2 GB/16 GB SE4710 No 2-Pin
TC25BJ-10B101xx WAN/LAN/PAN GMS 2 GB/16 GB SE2100 Yes Blank
TC25BJ-10C102xx WAN/LAN/PAN GMS 2 GB/16 GB SE4710 No 2-Pin
NOTE: Indonesia configurations do not support LTE.
Chapter Descriptions
Topics covered in this guide are as follows:
• Getting Started provides information on getting the TC25 up and running for the first time.
• Using the TC25 provides information for operating the TC25.
• Calls provides instructions for making phone calls.
Radios
Android 7.1
Operating System
Memory
RAM/Flash
Data Capture
8 MP Camera
Access Door
10
Page 11
• Applications provides information on using applications installed on the TC25.
• Data Capture provides information on capture barcode data.
• Wireless
• Accessories
• Maintenance and Troubleshooting
solutions for potential problems during TC25 operation.
• Technical Specifications provides the technical specifications for the TC25.
provides information on the various wireless options.
provides information on using the accessories for the TC25.
Notational Conventions
The following conventions are used in this document:
• Bold text is used to highlight the following:
• Dialog box, window and screen names
• Drop-down list and list box names
• Check box and radio button names
• Icons on a screen
• Key names on a keypad
• Button names on a screen.
• Bullets (•) indicate:
About This Guide
includes instructions on cleaning and provides troubleshooting
• Action items
• Lists of alternatives
• Lists of required steps that are not necessarily sequential.
• Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
Related Documents and Software
The following documents provide more information about the TC25 rugged smartphone.
• TC25 Quick Reference Guide, p/n MN-003052-xx
• TC25 Regulatory Guide, p/n MN-003053-xx
• TC25 Rugged Smartphone Integrator Guide, p/n MN-003055-xx
For the latest version of this guide and all guides, go to: zebra.com/support
Service Information
If you have a problem with your equipment, please use the Self-Help support resources available at
www.zebra.com. If the support provided via the Self-Help resources is not sufficient, you may contact Zebra Global
Customer Support for your region. Contact information is available at: zebra.com/support
.
.
When contacting support, please have the following information available:
• Serial number of the unit
11
Page 12
About This Guide
• Model number or product name
• Software type and version number.
Zebra responds to calls by email, telephone or fax within the time limits set forth in support agreements.
If your problem cannot be solved by Zebra Customer Support, you may need to return your equipment for servicing
and will be given specific directions. Zebra is not responsible for any damages incurred during shipment if the
approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your Zebra business product from a Zebra business partner, contact that business partner for
support.
Provide Documentation Feedback
If you have comments, questions, or suggestions about this guide, send an email to EVM-Techdocs@zebra.com.
12
Page 13
Getting Started
This chapter provides information for getting the device up and running for the first time.
Unpacking
Carefully remove all protective material from the TC25 and save the shipping container for later storage and
shipping.
1. Verify that the following were received:
• TC25 rugged smartphone
• Regulatory Guide.
2. Inspect the equipment for damage. If any equipment is missing or damaged, contact the Global Customer
Support center immediately.
3. Prior to using the TC25 for the first time, remove the protective shipping film that covers the scan window,
display and camera window.
13
Page 14
Features
7
1
2
3
4
5
8
9
11
12
10
6
13
Figure 1 TC25 Front View
Getting Started
Table 2 Front View Features
Number Item Function
1 Scan Button Initiates data capture (programmable).
Yellow button: TC25 with SE4710 imager.
Gray button: TC25 with SE2100 imager.
2 PTT Button Initiates push-to-talk communications (programmable).
3 Microphone Use for communications in Handset mode.
4 Power Contacts Provides power for charging the TC25.
5 USB-C Connector Provides USB host and client communications, and device charging via
cables and accessories.
6 Speaker Provides audio output for video and music playback. Provides audio in
7 Touch Screen Displays all information needed to operate the TC25.
8 Charging/Notification LED Indicates battery charging status while charging and application
speakerphone mode.
generated notifications.
9 Data Capture LED Indicates data capture status.
10 Microphone Use for communications in Speakerphone mode.
11 Receiver Use for audio playback in Handset mode.
14
Page 15
Getting Started
5
4
1
2
8
6
3
9
7
Table 2 Front View Features (Continued)
Number Item Function
12 Light Sensor Determines ambient light for controlling display backlight intensity.
13 Proximity Sensor Determines proximity for turning off display when in handset mode.
Figure 2 TC25 Rear View
Table 3 Back View Features
Number Item Function
1 Imager Window Provides data capture using the imager.
2 Power Button Turns the display on and off. Press and hold to reset the device or
power off the device.
3 Camera Flash Provides illumination for the camera.
4 Camera Takes photos and videos.
5 Scan Button Initiates data capture.
6 Volume Up/Down Button Increase and decrease audio volume.
7 Hand Strap Mount Point Provides latching point for the hand strap.
8 Access Door Provides access to microSD card slot and SIM card slot. Optional 2-Pin
Access Door is available on device with the SE4710 imager for use with
the Trigger Handle.
9 Hand Strap Mount Point Provides latching point for the hand strap.
15
Page 16
Setup
Perform this procedure to start using the TC2X for the first time.
1. Install a micro secure digital (SD) card (optional).
2. Installing a nano SIM card
3. Charge the TC25.
4. Power on the TC25.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the access door. Refer to
the documentation provided with the card for more information, and follow the manufacturer’s recommendations for
use.
CAUTION Use proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper
ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator
is properly grounded.
Getting Started
1. Using a 0# Phillips screwdriver, remove two screws securing the access door.
Figure 3 Remove Access Door
2. Remove access door.
16
Page 17
Getting Started
Figure 4 Remove Access Door
3. Align the microSD card with the SD card slot.
Figure 5 Align microSD Card
4. Push the microSD card into the SD card slot.
Figure 6 Push microSD Card into the SD Card Slot
5. Replace the access Door.
6. Secure the access door using the two screws.
17
Page 18
Figure 7 Secure Access Door
Installing the SIM Card
Getting Started
NOTE Only use a nano SIM card.
Only use nano SIM cards that meet the ESTI TS102.221 standard for nano SIM cards, form factor 4FF
(0.67 mm thick). Do not use SIM cards that are cut from thicker mini or micro SIM cards.
CAUTION Use proper electrostatic discharge (ESD) precautions to avoid damaging the SIM card. Proper ESD
precautions include, but not limited to, working on an ESD mat and ensuring that the user is properly
grounded.
1. Using a 0# Phillips screwdriver, remove two screws securing the access door.
Figure 8 Remove Access Door
2. Align the SIM card with the SIM card slot with the contacts facing down and the cut edge toward the top of the
device.
18
Page 19
Getting Started
Figure 9 Align SIM Card with Slot
3. Push the SIM card in until it locks into the slot.
Figure 10 Push SIM Card into Slot
4. Re-install the access door.
Figure 11 Replace Access Door
Charging the Battery
Before using the TC25 for the first time, charge the internal battery until the green Charging/Notification light
emitting diode (LED) remains lit. To charge the TC25 use a USB-C cable or a cradle with the appropriate power
supply. For information about the accessories available for the TC25 see Accessories for more information.
19
Page 20
Getting Started
The internal battery charges from fully depleted to 90% in approximately four hours and from fully depleted to
100% in approximately five hours.
NOTE In many cases the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for
approximately 10 hours of use.
Use only Zebra charging accessories and batteries. Charge batteries at room temperature with the TC25 in
sleep mode.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The TC25 or accessory always performs
battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the
TC25 or accessory may for small periods of time alternately enable and disable battery charging to keep the
battery at acceptable temperatures. The TC25 or accessory indicates when charging is disabled due to abnormal
temperatures via its LED and a notification appears on the display.
To charge the main battery:
1. Connect the charging accessory to the appropriate power source.
2. Insert the TC25 into a cradle or attach to a cable. The TC25 turns on and begins charging. The
Charging/Notification LED blinks amber while charging, then turns solid green when fully charged.
Figure 12 Charging with Cradle
IMPORTANT Use only the Zebra USB-C Cable for charging.
20
Page 21
Figure 13 Charging with USB Cable
Charging Indicators
Getting Started
Table 4 Charging/Notification LED Charging Indicators
State LED Indication
Off TC25 is not charging. TC25 is not inserted correctly in the
cradle or connected to a power source. Charger/cradle is
not powered.
Slow Blinking Amber (1 blink every 4
seconds)
Slow Blinking Red (1 blink every 4
seconds)
Solid Green Charging complete.
Solid Red Charging complete but the battery is at end of useful life.
Fast Blinking Amber (2 blinks/second) Charging error, e.g.:
TC25 is charging.
TC25 is charging but the battery is at end of useful life. See
system administrator for battery replacement services.
See system administrator for battery replacement services.
• Temperature is too low or too high.
• Charging has gone on too long without completion
(typically eight hours).
Fast Blinking Red (2 blinks/second) Charging error but the battery is at end of useful life., e.g.:
• Temperature is too low or too high.
• Charging has gone on too long without completion
(typically eight hours).
See system administrator for battery replacement services.
21
Page 22
Getting Started
Google Account Setup
NOTE The TC25 has to be connected to the internet in-order to set up a Google ™ account.
The first time the TC25 starts, the Setup Wizard displays. Follow the on-screen instructions to set up a Google
account, configure Google Wallet for purchasing items from the Play Store, entering your personal information, and
enabling backup/restore features.
Zebra Visibility Services
IMPORTANT Zebra Visibility Services applies to BSP 04-14-XX and above.
The TC25 captures and provides device analytics to a system administrator. The first time the TC25 boots (or after
a Factory and Enterprise reset), the Zebra Services agreement screen displays.
Figure 14 Zebra Services
Touch OK to allow the TC25 to send analytics data. Touch the Device Data switch to disable the TC25 from
sending analytics data and then OK.
Replacing the microSD Card
To replace the microSD card:
1. Press the Power button until the menu appears.
2. Touch Power off.
3. Touch OK.
4. If hand strap is attached, remove the hand strap.
5. Using a 0# Phillips screwdriver, remove two screws securing the access door.
22
Page 23
Getting Started
Figure 15 Remove Access Door
6. Remove access door.
7. Slide the microSD card out of the SD card slot.
Figure 16 Remove microSD Card
8. Lift the microSD card.
9. Align the replacement microSD card with the SD card slot.
Figure 17 Align microSD Card
10. Push the microSD card into the SD card slot.
23
Page 24
Getting Started
Figure 18 Push microSD Card into the SD Card Slot
11. Replace the access Door.
12. Secure the access door using the two screws.
Figure 19 Secure Access Door
13. Replace the hand strap, if required.
14. Press and hold the Power button to turn on the TC25.
Replacing the SIM Card
NOTE Only use a nano SIM card.
CAUTION Access door must be replaced and securely seated to ensure proper device sealing.
TC25 must be powered off when replacing the SIM card.
To replace the SIM card:
1. Press the Power button until the menu appears.
2. Touch Power off.
3. Touch OK.
4. If hand strap is attached, slide the hand strap clip up toward the top of the TC25 and then lift.
5. Using a 0# Phillips screwdriver, remove two screws securing the access door.
24
Page 25
Getting Started
Figure 20 Remove Access Door
6. Push the SIM card in to eject the card.
7. Remove the SIM card from the slot.
8. Align the replacement SIM card with the SIM card slot with the contacts facing down and the cut edge toward
the top of the device.
Figure 21 Align SIM Card with Slot
9. Push the SIM card in until it locks into the slot.
Figure 22 Push SIM Card into Slot
10. Re-install the access door.
25
Page 26
Getting Started
Figure 23 Replace Access Door
11. Replace the hand strap, if required.
12. Press and hold the Power button to turn on the TC25.
Accessing Device Settings
Throughout this guide, the user can access device settings:
1. Swipe down from the status bar and then touch .
2. On the Home screen, swipe up from the bottom of the screen and touch .
Battery Management
NOTE Prior to checking the battery charge level, remove the TC25 from any AC power source (cradle or cable).
To check the charge status of the main battery, open Settings and touch About phone > Battery
Management.
Battery status indicates that the battery is discharging and Battery level lists the battery charge (as a percentage
of fully charged).
Monitor Battery Usage
The Battery screen lists which applications consume the most battery power. Also use it to turn off applications
that were downloaded if they are consuming too much power.
1. Swipe down from the status bar and then touch .
2. Touch Battery.
26
Page 27
Getting Started
Figure 24 Battery Screen
The Battery screen lists the applications using the battery. The discharge graph at the top of the screen shows the
rate of the battery discharge since last charged (short periods of time when connected to a charger are shown as
thin green lines at the bottom of the chart), and how long it has been running on battery power.
Touch an application in the Battery screen to display details about its power consumption. Different applications
display different information. Some applications include buttons that open screens with settings to adjust power
use.
Low Battery Notification
When the battery charge level drops below 20%, the TC25 displays a notice to connect the TC25 to power.The
user should charge the battery using one of the charging accessories.
Figure 25 Low Battery Notification
When the battery charge drops below 10%, the TC25 displays a notice to connect the TC25 to power. The user
must charge the battery using one of the charging accessories.
When the battery charge drops below 4%, the TC25 turns off.
The user must charge the TC25 using one of the charging accessories.
Battery Optimization
Observe the following battery saving tips:
• Disable DataWedge Launcher profile. Refer to the TC25 Rugged Smartphone Integrator Guide for Android
7.1.2 for instructions.
• Set the screen to turn off after a short period of non-use. See Setting Screen Timeout Setting on page 29.
27
Page 28
• Set the TC25 to turn off when not in use. See Scheduled Power On and Off on page 52.
• Reduce screen brightness. See Setting the Screen Brightness on page 28.
• Turn off all wireless radios when not in use.
• Turn off automatic syncing for Email, Calendar, Contacts and other applications.
• Minimize use of applications that keep the TC25 from suspending, for example, music and video
applications.
Turning Off the Radios
To turn off all the radios:
1. Press the Power button until the menu appears.
2. Touch Airplane mode. The airplane icon appears in the Status bar indicating that all the radios are off.
Setting the Date and Time
The date and time is automatically synchronized using a NITZ server when the TC25 is connected to a cellular
network.The user is only required to set the time zone or set the date and time when not connected to a cellular
network or if the wireless LAN does not support Network Time Protocol (NTP).
Getting Started
1. Swipe down from the status bar and then touch .
2. Touch Date & time.
3. Touch Automatic date & time to disable automatic date and time synchronization.
4. Touch Set date.
5. In the calendar, set today’s date.
6. Touch OK.
7. Touch Set time.
8. Touch the green circle, drag to the current hour and then release.
9. Touch the green circle, drag to the current minute and then release.
10. Touch AM or PM.
11. Touch OK.
12. Touch Automatic time zone to disable automatic date and time synchronization.
13. Touch Select time zone.
14. Select the current time zone from the list.
15. Touch .
Display Setting
Use Display settings to change the screen brightness, change the background image, enable screen rotation, set
sleep time and change font size.
Setting the Screen Brightness
To manually set the screen brightness:
28
Page 29
Getting Started
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Slide the icon to adjust the screen brightness level.
Figure 26 Brightness Slider
To let the TC25 automatically adjust the screen brightness using the built-in light sensor:
1. Swipe down from the status bar and then touch .
2. Touch Display.
3. Touch Brightness Level.
4. Touch Adaptive brightness to automatically adjust the brightness.
5. Touch .
Setting Screen Rotation
By default, screen rotation is disabled. To enable screen rotation:
1. Swipe down from the status bar and then touch .
2. Touch Display.
3. Touch When device is rotated and select Rotate to contents of the screen to set the TC25 to automatically
switch orientation when the TC25 is rotated.
4. Touch .
Setting Screen Timeout Setting
To set the screen sleep time:
1. Swipe down from the status bar and then touch .
2. Touch Display.
3. Touch Sleep.
4. Select one of the sleep values.
• 15 seconds
• 30 seconds
• 1 minute (default)
• 2 minutes
• 5 minutes
• 10 minutes
• 30 minutes
5. Touch .
Setting Font Size
To set the size of the font is system applications:
29
Page 30
Getting Started
1. Swipe down from the status bar and then touch .
2. Touch Display.
3. Touch Font size.
Figure 27 Font Settings
4. Select one of the font size values.
• Small
• Default (default)
• Large
• Largest
5. Touch .
Setting the Charge LED
By default, the Charging/Notification LED is off when the device is charging and the screen is off. To turn on the
LED when the screen is off and the device is charging:
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch Display.
3. Touch Charging LED to enable the Charging/Notification LED when the screen is off.
Setting the Charge LED
The user can place the Charging/Notification LED in Standard Mode (default) or Quiet Mode. In Standard Mode,
the Charging/Notification LED is on when the device is charging, and the display is on or off. In Quiet Mode,
Charging/Notification LED is off when the screen is on and the device is charging, and on when the screen is off
and the device is charging.
To enable Quiet Mode:
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch Display.
30
Page 31
3. Touch Charging LED. The option switch turns green.
4. Touch .
General Sound Setting
Use the Sounds settings to configure media and alarm volumes.
1. Swipe down from the status bar and then touch .
2. Touch Sounds.
Figure 28 Sound and Notification Screen
Getting Started
• Media volume - Controls the music, games and media volume.
• Alarm volume - Controls the alarm clock volume.
• Ring volume - - Controls the ringtone volume.
• Also vibrate for calls - Turn on the switch to make the device vibrate when a call is received (default –
disabled).
• Do not disturb - Mutes the TC25 so that it does not make sounds or vibrate when you do not want it to.
• Priority only allows - Use to set priorities.
• Alarms - Disabled.
• Reminders - Switch on or off.
• Events - Switch on or off.
• Messages - Choose from anyone, starred contacts, any contact, or none. To star contacts, use
the Contacts app.
• Calls - Choose from anyone, starred contacts, any contact, or none. To star contacts, use the
Contacts app.
31
Page 32
Getting Started
• Repeat callers - Choose whether to let the TC25 ring if the same person calls again within 15
minutes.
• Automatic rules - To automatically silence the TC25 during certain times, like at night or on
weekends. Touch a default rule Weekend or Weeknight. Or, to make your own rule, tap Add rule and
then Time rule.
• Block visual disturbances
• Block when screen is on - option pertains to notifications you receive when you are actively
using the device. If you would like to disable the banner like notifications when Do not Disturb is
enabled, turn this option On. This will also prevent you from peeking at notifications.
• Block when screen is off - option pertains to notifications you receive when you are not using
your device i.e. the display is asleep. If you want to prevent the display from waking up when a
new notification is received, turn this option On. This will additionally disable the LED light alerts
your phone sends you when you have new notifications.
• Phone ringtone - Touch to select a sound to play for incoming calls.
• Default notification ringtone - Touch to select a sound to play for all system notifications.
• Default alarm ringtone - Touch to select a sound to play for alarms.
• Emergency broadcasts - Touch to configure emergency broadcast settings and notifications.
• Other sounds
• Dial pad tones - Play a sound when pressing keys on dial pad (default - disabled).
• Screen locking sounds - play a sound when locking and unlocking the screen (default – enabled)
• Charging sounds - Not applicable.
• Touch sounds - Play a sound when making screen selections (default – enabled).
• Vibrate on tap - Device vibrates when making screen selections (default – disabled).
Wake-Up Sources
By default the TC25 wakes from suspend mode when the user presses the power button. The TC25 can be
configured to wake when the user presses the PTT on the left side of the device or one of the Scan buttons.
1. Swipe down from the status bar and then touch .
2. Touch Wake-Up Sources.
3. Touch Keypad checkbox. A check appears in the checkbox.
32
Page 33
Figure 29 Wake-Up Sources
4. Touch .
Getting Started
33
Page 34
Using the TC25
This chapter explains the buttons, status icons, and controls on the TC25, and provides basic instructions for using
the TC25 including resetting the TC25 and entering data.
Google Mobile Services
The TC25 with GMS contains applications and services that provide additional functionality to the TC25.
GMS includes:
• Applications - GMS adds a variety of Google applications and associated widgets including Chrome,
Gmail, Drive and Maps.
• Services:
• Speech to Text - Allows for free format speech to text, in many languages for both connected and
disconnected network. Launch by touching the microphone icon on the keyboard.
• TalkBack Service - Provides spoken feedback on various parts of the user interface. To enable, go to
Settings > Accessibility.
• Network Location Provider - Adds a location provider which uses mobile network tower information
and Wi-Fi access point information to provide a location without using GPS. To enable, go to Settings
> Location.
• Widevine DRM - Enables the digital rights management so that protected content can be played.
Enable via DRM Info from the Play Store.
• Google Cloud Messaging - Allows the sending of data from your server to your TC25 and also to
receive messages from devices on the same connection.
• Backup and Restore - Allows the users settings and applications to be backed up to a Google server
and subsequently restored from that server after a factory reset.
• Google accounts - Create and use a Google account to synchronize mail, files, music, photos, contacts
and calendar events.
Home Screen
The Home screen displays when the TC25 turns on. Depending upon the configuration, the Home screen might
appear different. Contact your system administrator for more information.
After a suspend or screen time-out, the Home screen displays with the lock sliders. Touch the screen and slide up
to unlock. For screen locking information see Un-Locking the Screen on page 51.
34
Page 35
Figure 30 Home Screen
1
7
543
8
6
2
Using the TC25
Table 5 Home Screen Items
Item Description
1 — Status Bar Displays the time, status icons (right side), and notification icons (left
side). For more information see Status Bar on page 36 and Managing
Notifications on page 38.
2 — Widgets Launches stand-alone applications that run on the Home screen. See
Application Shortcuts and Widgets on page 41 for more information.
3 — Back Displays the previous screen.
4 — Home Displays the Home screen.
5 — Recent Button Displays recently used applications.
6 — All Apps Opens the APPS window.
7 — Shortcut Icons Opens applications installed on the TC25. See Application Shortcuts
and Widgets on page 41 for more information.
8 — Folder Contains apps.
The Home screen provides four additional screens for placement of widgets and shortcuts. Swipe the screen left or
right to view the additional screens.
Setting Home Screen Rotation
By default the Home screen rotation is disabled. To enable Home screen rotation:
1. Touch and hold anywhere on the Home screen until the options appear.
2. Touch .
3. Touch Allow rotation switch.
4. Touch .
35
Page 36
Using the TC25
Notification Icons Status Icons
5. Rotate the device.
Figure 31 Rotated Home Screen
Status Bar
The Status bar displays the notification icons (left side), time and status icons (right side).
NOTE Some status icons may not appear in the Status bar if there are too many icons to display.
Figure 32 Notification and Status Icons
If there are more notifications than can fit in the Status bar , displays indicating that more notifications exist.
Open the Notifications panel to view all notifications and status.
Status Icons
Table 6 Status Icons
Icon Description
Indicates that the Alarm is active.
Indicates that the main battery is fully charged.
Indicates that the main battery is partially drained.
Indicates that the main battery charge is low.
Indicates that the main battery charge is very low.
Note 1: Cellular network icon that appears is dependent upon the carrier/network.
36
Page 37
Using the TC25
Table 6 Status Icons (Continued)
Icon Description
Indicates that the main battery is charging.
Indicates that all sounds except media and alarms are silenced and vibrate mode is active.
Indicates that the Airplane Mode is active. All radios are turned off.
Indicates that Bluetooth is on.
Indicates that the TC25 is connected to a Bluetooth device.
Connected to a Wi-Fi network.
Not connected to a Wi-Fi network or no Wi-Fi signal.
Connected to an Ethernet network.
Portable Wi-Fi Hotspot is active.
Mobile network signal strength.
No mobile network signal.
Connected to a 4G LTE network (see Note 1).
Connected to a DC -HSPA, HSDPA, HSPA+, HSUPA, LTE or WCDMA network (see Note 1).
Connected to a WCDMA network (see Note 1).
Connected to an DC - HSPA, HSDPA, HSPA+ or HSUPA network (see Note 1).
Connected to an EDGE network (see Note 1).
Connected to a GPRS network (see Note 1).
Connected to a GPRS network (see Note 1).
Roaming from a network.
No SIM card installed.
Note 1: Cellular network icon that appears is dependent upon the carrier/network.
37
Page 38
Using the TC25
Notification Icons
Table 7 Notification Icons
Icon Description
Indicates the main battery is low.
Indicates that more notifications are available for viewing.
Indicates that data is syncing.
Indicates an upcoming event.
Indicates that an open Wi-Fi network is available.
Indicates that a song is playing.
Indicates that a problem with sign-in or sync has occurred.
Indicates that the TC25 is uploading data.
Indicates that the TC25 is downloading data when animated and download is complete when static.
Indicates that USB tethering is active.
Indicates that the TC25 is connected to or disconnected from virtual private network (VPN).
Preparing Internal Storage.
Indicates that USB debugging is enabled on the TC25.
USB Headset is connected to device.
Indicates the status of the PTT Express Voice Client. See Notification Icons for complete list of PTT
Express notification icons.
Indicates that RxLogger application is running.
Indicates a Bluetooth scanner is connected to the TC25.
Managing Notifications
Notification icons report the arrival of new messages, calendar events, and alarms, as well as ongoing events.
When a notification occurs, an icon appears in the Status bar with a brief description. See Notification Icons on
page 38 for a list of possible notification icons and their description. Open the Notifications panel to view a list of all
the notifications.
To open the Notification panel drag the Status bar down from the top of the screen.
38
Page 39
Using the TC25
Figure 33 Notification Panel
To respond to a notification, open the Notifications Panel and then touch a notification. The Notifications Panel
closes and the subsequent activity is dependent on the notification.
To clear all notifications, open the Notifications Panel and then touch CLEAR ALL. All event-based notifications
are removed. Ongoing notifications remain in the list.
Ongoing notifications remain in the list.
To close the Notification Panel, swipe the Notifications Panel up.
Setting Application Notifications
To change notification settings for a specific app:
1. Swipe down from the status bar and then touch .
2. Touch Notifications.
3. Select an app.
4. Select an available option:
• Block all
• Show silently
• On the lock screen
• Override Do Not Disturb.
IMPORTANT In the notification, slide the notification slightly left or right and touch .
Viewing Notification Settings for All Apps
1. Swipe down from the status bar and then touch .
2. Touch Notifications.
3. Touch down-arrow next to All apps.
4. To see all the apps currently set to a specific setting, touch that setting.
Controlling Lock Screen Notifications
To control notification content on the lock screen:
1. Swipe down from the status bar and then touch .
2. Touch Notifications > .
3. Touch On the lock screen.
4. Select Show all notification content to or select Don’t show notifications at all.
39
Page 40
Using the TC25
Quick Settings
Use Quick Settings to get to frequently used settings, like turning on airplane mode. To open Quick Settings bar,
swipe down from the top of the screen with two fingers or twice with one finger.
Figure 34 Quick Settings Bar
To see the full Quick Settings panel:
• If the TC25 is locked, swipe down once.
• If the TC25 is unlocked, swipe down once with 2 fingers, or twice with one finger.
• If the Quick Settings bar is open, touch the Down arrow.
Figure 35 Full Quick Settings
Available setting tiles:
• Display brightness: Slide to lower or increase the brightness of the screen.
• Wi-Fi network: Turn Wi-Fi on or off. To open Wi-Fi settings, touch the Wi-Fi network name.
• Bluetooth settings: Turn Bluetooth on or off. To open Bluetooth settings, touch the Bluetooth.
• Do not disturb: Control how and when to receive notifications.
• Cellular Network: Displays the cellular carrier name and signal information. No SIM card indicates that a
SIM card is not installed or activated.
• Airplane mode: Turn airplane mode on or off. Airplane mode means device will not connect to Wi-Fi or
Bluetooth.
• Auto-rotate: Lock the device’s orientation in portrait or landscape mode or set to automatically rotate.
• Flashlight: Turn camera flash on or off.
• Location: Enable or disable locationing feature.
• Hotspot - Turn mobile hotspot on or off.
• Invert colors - Invert the display colors.
• Data Saver - Turn on to prevent some apps from sending or receiving data in the background.
• Night Light - Tint the screen amber to make it easier to look at the screen in dim light. Set Night Light to
turn on automatically from sunset to sunrise, or at other times.
40
Page 41
Using the TC25
• Nearby - Helps find and interact with services and devices close to the device.
Edit Icons on Quick Settings
The first several setting tiles become the Quick Settings bar.
To move a setting tile:
1. Touch and drag a setting tile to another location.
2. Release the tile.
3. Touch to save tiles and return to quick settings.
To add a setting tile:
1. Open Quick Settings.
2. Touch .
3. Slide Quick Settings panel up to reveal additional tiles.
4. Touch and drag a setting tile from the Drag to add tiles area to the main area.
5. Release the tile.
6. Touch to save tiles and return to quick settings.
To remove a setting tile:
1. Open Quick Settings.
2. Touch .
3. Touch and drag a setting tile to the Drag here to remove area.
4. Release the tile.
5. Touch to save tiles and return to quick settings.
Application Shortcuts and Widgets
Application shortcuts placed on the Home screen allow quick and easy access to applications. Application Widgets
are self-contained applications placed on the Home screen to access frequently used features.
Adding an Application to the Home Screen
1. Go to the desired Home screen.
2. Swipe up from the bottom of the screen.
3. Scroll through the list to find the application icon.
4. Touch and hold the icon until the Home screen appears.
5. Position the icon on the screen and then release.
Adding a Widget to the Home Screen
To add a widget to the Home screen:
1. Go to the desired Home screen.
2. Touch and hold until the menu appears.
3. Touch WIDGETS.
4. Scroll through the list to find the widget.
41
Page 42
Using the TC25
5. Touch and hold the widget until the Home screen appears.
6. Position the widget on the screen and then release.
Moving Items on the Home Screen
1. Touch and hold the item until it floats on the screen.
2. Drag the item to a new location. Pause at the edge of the screen to drag the item onto an adjacent Home
screen.
3. Lift finger to place the item on the Home screen.
Removing an Application Shortcut or Widget from the Home Screen
1. Go to the desired Home screen.
2. Touch and hold the application shortcut or widget icon until it floats on the screen.
3. Drag the icon to Removeon the top of the screen and then release.
Folders
Use Folders to organize similar applications together. Tap the folder to open and display items in the folder.
Creating a Folder
To create a folder, there must be at least two app icons on the Home screen.
1. Go to the desired Home screen.
2. Touch and hold on one application icon.
3. Drag the icon and stack on top of another icon.
4. Lift and release.
Naming Folders
To name a folder:
1. Touch the folder.
Figure 36 Open Folder
2. Touch the title area and enter a folder name using the keyboard.
3. Touch on the keyboard.
4. Touch anywhere on the Home screen to close the folder. The folder name appears under the folder.
Figure 37 Renamed Folder
Removing a Folder
To remove a folder:
42
Page 43
1. Touch and hold the folder icon until it enlarges.
2. Drag the folder to Remove and release.
Home Screen Wallpaper
To change the Home screen wallpaper:
1. Touch and hold on the screen until the menu appears.
2. Touch WALLPAPERS.
3. Touch My photos to select a photo from Gallery or select one of the pre-installed photos.
4. Touch Save wallpaper.
Using the Touchscreen
Use the multi-tap sensitive screen to operate the device.
• Tap - Tap to:
• select items on the screen
• type letters and symbols using the on-screen keyboard
• press on-screen buttons.
Using the TC25
• Tap and Hold - Tap and hold:
• an item on the Home screen to move it to a new location or to the trash.
• an item in Apps to create a shortcut on the Home screen.
• the Home screen to open a menu for customizing the Home screen.
• an empty area on the Home screen until the menu appears.
• Drag - Tap and hold an item for a moment and then move finger on the screen until reaching the new
position.
• Swipe- Move finger up and down or left and right on the screen to:
• unlock the screen
• view additional Home screens
• view additional application icons in the Launcher window
• view more information on an application’s screen.
• Double-tap - Tap twice on a web page, map, or other screen to zoom in and out.
• Pinch - In some applications, zoom in and out by placing two fingers on the screen and pinching them
together (to zoom out) or spreading them apart (to zoom in).
On-Screen Keyboards
Use the on-screen keyboard to enter text in a text field.
Editing Text
Edit entered text and use menu commands to cut, copy, and paste text within or across applications. Some
applications do not support editing some or all of the text they display; others may offer their own way to select text.
43
Page 44
Using the TC25
Entering Numbers, Symbols and Special Characters
To enter numbers and symbols:
• Touch and hold one of the top-row keys until a menu appears then select a number. Keys with alternate
characters display an ellipsis ( ... ) below the character.
• Touch and hold the Shift key with one finger, touch one or more capital letters or symbols to enter them,
and then lift both fingers to return to the lowercase keyboard.
• Touch to switch to the numbers and symbols keyboard.
• Touch the key on the numbers and symbols keyboard to view additional symbols.
To enter special characters, touch and hold a number or symbol key to open a menu of additional symbols.
• A larger version of the key displays briefly over the keyboard.
• Keys with alternate characters display an ellipsis ( ... ) below the character.
Switching Language Keyboards
The user can enable multiple language keyboards. The available language codes appear on the space bar.
Figure 38 Keyboard with Multiple Languages
To switch between language keyboard, touch at the bottom right corner of the screen.
Figure 39 Change Keyboard Option
Select one of the keyboard languages. The keyboard automatically changes to the selected language.
Configuring the Keyboard
To configure the keyboard, See the Keyboard Settings section in the TC25 Rugged Smartphone Integrator Guide
for Android Version 7.1.2.
GMS Keyboard
To configure the keyboard settings, touch and hold (comma) > and then select Gboard Keyboard settings.
44
Page 45
Do Not Disturb Feature
This mode mutes the TC25 so that it does not make sounds or vibrate.
For example, use Do Not Disturb to:
• Automatically limit sounds at night or during events
• Mute interruptions other than alarms
• Get alerted to messages only from favorite contacts.
Limit Sounds and Vibrations
Mute the TC25 completely, or let through the important alarms or important calls.
Total Silence
To completely mute the TC25 so that it does not make a sound or vibrate, choose Total silence.
In Total silence mode:
• Alarms do not make noise.
• TC25 does not vibrate or make sounds when receiving a message, or notification.
Using the TC25
• Sounds from music, videos, games, and other media are muted.
NOTE: The user will not hear alarms in Total silence mode.
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Total silence.
3. Choose Until you turn it off or select a time period.
4. Touch Done.
When Total Silence is on, appears in the quick access panel and the Status Bar.
To turn off Total Silence, open quick access panel and touch Total silence.
Alarms Only
To mute the TC25 so that the user hears alarms, choose Alarms only. This option does not mute sounds from
music, videos, games, or other media.
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Alarms only.
3. Choose Until you turn it off or select a time period.
4. Tap Done.
When Alarms Only is on, appears in the quick access panel and the Status Bar.
To turn off Alarms Only, open quick access panel and touch Alarms only.
45
Page 46
Using the TC25
NOTE: To quickly turn on Alarms Only, with the screen on, press and hold the Volume Down button until the
volume is all the way down. Then, press Volume Down again to turn on Alarms Only.
To turn off Alarms Only, press either the Volume Up or Volume Down button and the touch END NOW in
the alert message. Then, press Volume Up again to turn on Alarms Only.
Priority Notifications Only
To only be interrupted by important notifications, choose Priority Only. This option does not mute sounds from
music, videos, games, or other media.
Before turning on Priority Only mode, set the notification priorities:
1. Swipe down from the status bar and then touch .
2. Touch Sounds > Do not disturb > Priority only allows.
3. Set priorities.
• Alarms: Disabled by default.
• Reminders and Events: Switch on or off.
• Messages: Choose From anyone, From contacts only, From starred contacts only, or none. To star
contacts, use the Contacts app.
• Calls: Choose From anyone, From contacts only, From starred contacts only, or none. To star
contacts, use the Contacts app.
• Repeat callers: Choose whether to let the TC25 ring if the same person calls again within 15 minutes.
After setting notification priorities, turn on Priority only mode to limit interruptions. The priority notifications make a
sound or vibrate based on the current ringer volume, but other notifications will be silenced.
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Priority only.
3. Choose Until you turn it off or select a time period.
4. Tap Done.
When Priority Only is on, appears in the quick access panel and the Status Bar.
To turn off Priority Only, open quick access panel and touch Priority only.
Automatically Block Sounds and Vibrations
Silence Sounds During Certain Times
To automatically silence the TC25 during certain times, like at night or on weekends, set the time rules.
1. Swipe down from the status bar and then touch .
2. Touch Sounds > Do not disturb > Automatic rules.
3. Touch a default Weekend or Weeknight. Or, to make a new rule, touch Add rule and then Time rule.
4. Edit the new rule:
• Rule name: Name the rule.
• Days, Start time, and End time: Set the rule's schedule.
46
Page 47
Using the TC25
• Do not disturb: Choose whether the rule uses Alarms only, Priority only, or Total silence.
5. Touch the On/Off text or switch at the top to turn on the rule.
Silence Sounds During Events and Meetings
To automatically silence the TC25 during events or meetings, set an event rules.
1. Swipe down from the status bar and then touch .
2. Touch Sounds > Do not disturb > Automatic rules.
3. To edit the default rule, touch Event. Or, to create a new rule, touch Add rule > Event rule.
4. Edit the rule settings.
• During events for: Select which Google Calendar events the rule uses.
• Where reply is: Options: Yes, Maybe, or Not replied, Yes or Maybe, or Yes.
• Do not disturb: Choose whether the rule uses Priority only, Alarms only, or Total silence.
5. Touch the On/Off switch at the top to turn on the rule.
Turn Sounds Back On
When the TC25 is in Do Not Disturb mode, Alarms or Priority only or Total silence display.
To turn off Do Not Disturb, either:
• In the quick access panel, touch Alarms only, Priority only, or Total silence.
• Press the Volume Down button and touch End Now.
Override Do Not Disturb for Specific Apps
To let through notifications from specific apps:
1. Open Settings > Notifications.
2. Touch an app.
3. Touch Override Do Not Disturb.
47
Page 48
Applications
The APPS screen displays icons for all installed applications. The table below lists the applications installed on the
TC25. Refer to the TC25 Rugged Smartphone Integrator Guide for Android Version 7.1 for information on installing
and uninstalling application.
Table 8 Applications
Icon Description
Using the TC25
Bluetooth Pairing Utility – Use to pair a Bluetooth Imager with the TC25 by scanning a
barcode.
Calculator - Provides the basic and scientific arithmetic functions.
Camera - Take photos or record videos.For more information see Camera on page 74.
Chrome - Use to access the Internet or intranet.
Clock - Use to schedule alarms for appointments or as a wake-up.
Contacts - Use to manage contact information. See Contacts on page 72 for more information.
DataWedge - Enables data capture using the imager.
Diagnostic Tool - Use to diagnose the TC25. Refer to the TC25 Rugged Smartphone Integrator
Guide for Android Version 7.1.2 for more information.
Downloads - lists all downloads files.
Drive - Upload photos, videos, documents, and other files to personal storage site.
Duo - A one-to-one video calling application.
48
Page 49
Using the TC25
Table 8 Applications (Continued)
Icon Description
DWDemo - Provides a way to demonstrate the data capture features using the imager. See
DataWedge Demonstration on page 84 for more information.
File Browser - Organize and manage files on the TC25. See File Browser on page 68 for more
information.
Gmail - Use to send and receive email using a Google email account.
Google - Launches Google search application.
Install ATL - Use to download and install the Asset Tracker Lite application from the Zebra
Support site. (BSP 04-14-XX and above only).
For information on Asset Tracker Lite application, refer to the Asset Tracker Lite User Guide.
Maps - Use to see you location on a map (with public transit, traffic or satellite overlays). Search
for any business or place of interest. Provides turn-by-turn navigation with voice guidance and
traffic-avoidance and alternate routes, for drivers, cyclist, walkers and users of public
transportation.
Messaging - Send SMS and MMS messages. See Messaging on page 70 for more information.
Notes - Use to take and save notes.
Phone - Use to make cellular calls or to dial a phone number when used with some Voice over
IP (VoIP) clients.
Photos - Use to sync photos with Google account.
Play Movies & TV - View movies and video on your device.
Play Music - Use to listen to music.
Play Store - Download music, movies, books, and Android apps and games from the Google
Play
™ Store.
49
Page 50
Using the TC25
Table 8 Applications (Continued)
Icon Description
PTT Express - Use to launch PTT Express client for VoIP communication.
RxLogger - Use to diagnose device and application issues. See the TC25 Rugged Smartphone
Integrator Guide for Android Version 7.1.2 for more information.
RxLogger Utility - Use to diagnose device and application issues. See the TC25 Rugged
Smartphone Integrator Guide for Android Version 7.1.2 for more information.
Settings - Use to configure the TC25.
Sound Recorder - Use to record audio.
StageNow - Allows the TC25 to stage a device for initial use by initiating the deployment of
settings, firmware and software.
TC25 User Guide - Opens the on-device User Guide for the TC25.
Voice Search - Use to perform searches by asking questions.
YouTube
™ - Use to view videos on the YouTube web site.
Accessing Applications
All applications installed on the device are accessed using the APPS window.
1. Swipe up from the bottom of the Home screen.
50
Page 51
Using the TC25
Figure 40 APPS Window Example
2. Slide the APPS window left or right to view more application icons. Touch an icon to open the application.
See Application Shortcuts and Widgets on page 41 for information on creating a shortcut on the Home screen.
Switching Between Recent Applications
1. Touch . A window appears on the screen with icons of recently used applications.
Figure 41 Recently Used Applications
2. Slide the window up and down to view all recently used applications.
3. Swipe left or right to remove application from the list and force close the application.
4. Touch an icon to open it or touch to return to the current screen.
Un-Locking the Screen
Use the Lock screen to protect access to data on the TC25. Some email account require locking the screen. Refer
to the TC25 Rugged Smartphone Integrator Guide for Android Version 7.1.2 for information on setting up the
locking feature.
51
Page 52
Using the TC25
When locked, a pattern, PIN or password is required to unlock the device. Press the Power button to lock the
screen. The device also locks after a pre-defined time-out.
Press and release the Power button to wake the device. The Lock screen displays. Swipe the screen up to unlock.
If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen. If the PIN or
Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
Figure 42 Lock Screen
Figure 43 PIN Screen Example
Scheduled Power On and Off
The user can set the TC25 to turn on or off at a specific time. This can save battery power when the TC25 is not in
use.
To set the power on and off schedule:
1. Swipe down from the status bar and then touch .
2. Touch Scheduled power on and off.
52
Page 53
Using the TC25
Figure 44 Scheduled Power On and Off
3. In the Scheduled power on section, touch the on/off switch.
Figure 45 Set Power Schedule
4. Touch the time.
5. Use the clock dialog box to set the power on time and touch Done. by default, the power on time occurs
everyday.
6. Touch the day circles disable power on for a specific day.
7. Deselect the Repeat checkbox to disable daily repeating and set the TC25 power on at the next set time.
8. Repeat for scheduled power off settings.
9. Touch .
When the TC25 starts automatic power off, a dialog box appears.
53
Page 54
Figure 46 Power Off
Touch Shutdown to power off, Cancel to not power off or the device powers off automatically after a 20 seconds.
Resetting the Device
There are two reset functions, soft reset and hard reset.
Performing a Soft Reset
Perform a soft reset if applications stop responding.
1. Press and hold the Power button until the menu appears.
2. Touch Reset.
3. The device reboots.
Using the TC25
Performing a Hard Reset
CAUTION Performing a hard reset with a microSD card installed in the TC25 may cause damage or data corruption to
the microSD card.
Perform a hard reset if the TC25 stops responding.
1. Simultaneously press the Power and Volume Up buttons for at least five seconds.
2. When the screen turns off, release the buttons.
3. The TC25 reboots.
Suspend Mode
The TC25 goes into suspend mode when the user presses the Power button or after a period of inactivity (set in
the Display settings window).
To wake the TC25 from Suspend mode, press the Power button. The Lock screen displays. Swipe the screen up to
unlock. If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen. If
the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
NOTE If the user enters the PIN, password or pattern incorrectly five times, they must wait 30 seconds before
trying again.
If the user forgets the PIN, password or pattern contact the system administrator.
54
Page 55
Using the TC25
Transferring Files with a Host Computer via USB
Connect the TC25 to a host computer using the USB Charging cable or the 1-Slot USB cradle to transfer files
between the TC25 and the host computer. See Accessories for more information.
When connecting the TC25 to a host computer, follow the host computer’s instructions for connecting and
disconnecting USB devices, to avoid damaging or corrupting files.
Transferring Files using Media Transfer Protocol
NOTE Use Media Transfer Protocol (MTP) to copy files between the TC25 (internal memory or microSD card)
and the host computer.
1. Connect the Rugged Charge/USB Cable to the TC25 or place the TC25 into the 1-Slot USB/Charge Only
Cradle. See Accessories for setup information.
2. Pull down the Notification panel and touch USB charging this device.
Figure 47 Use USB Dialog Box
3. Touch Transfer files.
4. On the host computer, open a file explorer application.
5. Locate the TC25 as a portable device.
6. Open the SD card or the Internal storage folder.
7. Copy files to and from the TC25 or delete files as required.
Transferring Files using Photo Transfer Protocol
NOTE Use Photo Transfer Protocol (PTP) to copy photos from either the microSD card or internal memory to the
host computer.
1. Connect the USB Cable to the TC25 or place the TC25 into the 1-Slot Ethernet Cradle. See Accessories for
setup information.
2. Pull down the Notification panel and touch USB charging this device.
55
Page 56
Using the TC25
Figure 48 Use USB Dialog Box
3. Touch Transfer photos (PTP).
4. On the host computer, open a file explorer application.
5. Open the SD card or the Internal storage folder.
6. Copy or delete photos as required.
Disconnect from the Host Computer
CAUTION Carefully follow the host computer’s instructions to unmount the microSD card and disconnect USB
devices correctly to avoid losing information.
1. On the host computer, unmount the device.
2. Remove the USB Charging cable from the device or remove the device from the cradle.
56
Page 57
Calls
Make a phone call from the Phone application, the Contacts application or other applications or widgets that
display contact information.
Emergency Calling
The service provider programs one or more emergency phone numbers, such as 911 or 999, that the user can call
under any circumstances, even when the phone is locked, a SIM card is not inserted or the phone is not activated.
The service provider can program additional emergency numbers into the SIM card. However, the SIM card must
be inserted in the device in order to use the numbers stored on it. See the service provider for additional
information.
NOTE: Emergency numbers vary by country. The phone’s pre-programmed emergency number(s) may not
work in all locations, and sometimes an emergency call cannot be placed due to network, environmental, or
interference issues.
Audio Modes
The device offers three audio modes for use during phone calls:
• Handset Mode: Switches audio to the receiver at the top front of the device, so the user can use the
device as a handset. This is the default mode.
• Speaker Mode: Use the device as if on speaker phone.
• Headset Mode: Connect a Bluetooth ear bud headset to automatically switch audio to the headset.
Using a Bluetooth Headset
Use a Bluetooth headset for audio communication when using an audio-enabled application. See Bluetooth on
page 116 for information on connecting a Bluetooth headset to the device. Set the volume appropriately before
putting on the headset. When a Bluetooth headset is connected, the speakerphone is muted.
Adjusting Audio Volume
Use the Volume buttons to adjust the volume of the ringer when not in a call and the audio volume when in a call.
57
Page 58
NOTE: Adjust the conversation phone volume during a call. Adjusting the volume while not in a call affects the
ring and notification sound levels.
Making a Call Using the Dialer
Use the dialer tab to dial phone numbers.
1. On the Home screen touch .
2. Touch .
Figure 49 Dialer Screen
Calls
3. Touch the keys to enter the phone number.
4. Touch below the dialer to initiate the call.
58
Page 59
Figure 50 Call in Progress
Calls
• - touch to send audio to the speakerphone.
• - touch to mute the call.
• - touch to display the dial pad.
• - touch to place the call on hold (not available on all services).
• - touch to create a conference call.
• - touch to turn volume boost on or off.
5. Touch to end the call.
If using a Bluetooth headset, additional audio options are available. Touch the audio icon to open the audio menu.
Figure 51 Bluetooth Audio Options
• - indicates that audio is routed to the Bluetooth headset.
59
Page 60
• - indicates that audio is routed to the speakerphone.
• - indicates that audio is routed to the earpiece.
Dialer Dialing Options
The dialer provides options to save the dialed number to contacts, insert pauses and wait into the dial string and
options for setting the Call settings. Enter at least one digit to access these options. Touch to access the
following:
• Add 2–sec pause - pause the dialing of the next number for two seconds. Multiple pauses can be added
sequentially.
• Add wait - wait for confirmation to send the rest of the digits.
Making a Call Using Contacts
There are two ways to make a call using contacts:
• Using the Dialer
• Using the Contacts application.
Calls
Using the Dialer
1. On the Home screen touch .
2. Touch the tab.
Figure 52 Dialer Contacts Tab
3. Touch the contact.
4. Touch to initiate the call.
5. Touch to end the call.
60
Page 61
Using the Contacts Application
To make a call from the Contacts application:
1. Touch .
Figure 53 Contact Application
Calls
2. Touch a contact name.
3. Touch to initiate a call.
Making a Call Using Call History
Call History is a list of all the calls placed, received, or missed. It provides a convenient way to redial a number,
return a call, or add a number to Contacts.
Arrow icons beside a call indicate the type of call. Multiple arrows indicate multiple calls:
• - Missed incoming call
• - Received incoming call
• - Outgoing call.
1. On the Home screen touch .
2. Touch the tab.
61
Page 62
Figure 54 Call History Tab
3. Touch next to the contact to initiate the call.
4. Touch the contact to perform other functions.
Calls
5. Touch to end the call.
Making a Conference Call
To create a conference phone session with multiple people.
NOTE: Conference Calling and the number of conference calls allowed may not be available on all services.
Please check with the service provider for Conference Calling availability.
On the Home screen touch .
1. Touch .
2. Touch the keys to enter the phone number.
3. Touch below the dialer to initiate the call.
4. When the call connects, touch .
5. Select a contact or touch and enter the second phone number.
6. Touch below the dialer to initiate the call. The first call is placed on hold.
7. When the call connects, the first call is placed on hold and the second call is active.
62
Page 63
Calls
Figure 55 Two Calls
8. Touch icon to create a conference call with three people.
Figure 56 Merged Calls
9. Touch to add another call.
The conference is placed on hold.
10. Touch the keys to enter the another phone number.
11. Touch below the dialer to initiate the call.
12. Touch to add the third call to the conference.
13. Touch Manage Conference call to view all callers.
63
Page 64
Calls
Figure 57 Un-merge Calls
14. To remove a caller from the conference, touch next to the caller.
To speak privately with one party during a conference call, touch . To include all parties again, touch .
Making a Call Using a Bluetooth Headset
To make a call using a Bluetooth headset:
1. Pair the Bluetooth headset with the device.
2. Press the Call button on the Bluetooth headset.
3. Say “Call” and then the number or contact name.
4. Press the Call button on the Bluetooth headset to end the call.
Answering Calls
When you receive a phone call, the Incoming Call screen displays, displaying the caller ID and any additional
information about the caller that is in the Contacts application.
Figure 58 Incoming Call Screen
Touch Answer to answer the call or Dismiss to send the caller to voice mail.
If the screen lock is enabled, the user can still answer the call without unlocking the device.
64
Page 65
Calls
Figure 59 Incoming Call Locked Screen
When a call arrives, touch the white phone icon and slide over one of these icons:
• Answer call - Start talking to the caller.
• Send to voice mail - Direct the caller to leave a voice mail message.
• Send a message - Opens a list of quick text responses. Touch one to send it to the caller immediately.
When the calls ends, the device remains locked.
If using a Bluetooth headset, when a call arrives, touch the Call button on the Bluetooth headset to answer the call.
To end the call press the headset Call button.
All incoming calls are recorded in the Phone application Call log tab. If you miss a call, you receive a notification.
To silence the ringer before answering the call, press the volume down button on the side of device.
Call Settings
IMPORTANT: Not all options are available for all configurations.
Use the Call Settings to modify options related to the phone call feature. On the Call home screen, touch >
Settings.
Display Options
• Sort by - Options: First name or Last name.
• Name format - Options: First name first or Last name first.
Use the Call Settings to modify options related to the phone call feature.
Sounds and Vibrations
• Phone ringtone - Touch to select a ringtone to sound when an incoming call is received.
• Also vibrate for calls - Check to make the device vibrate when a call is received (default - disabled).
• Dialpad tones - Check to play a sound when a phone key is touched (default - enabled).
65
Page 66
Calls
• Dialpad tone length - Select dialpad tone length. Options: Normal or Long.
Quick Responses
Touch to edit quick responses to use instead of answering a call.
Speed Dial Settings
Set speed dial contact shortcuts.
Calls
• Calling accounts
• SIP accounts - Choose to receive Internet calls for accounts added to the device, view or change SIP
accounts, or add an Internet calling account.
• Use SIP calling - Options: For all calls or Only for SIP calls (default).
• Receive incoming calls - When enabled, allows incoming calls (deafult - disabled).
• Voicemail - Touch to configure voicemail settings.
• Service - Set the service provider or other provider for voicemail service.
• Setup - Touch to update the phone number used to access voicemail.
• Sound - Touch to select a sound to play when a voicemail is received.
• Vibrate - Set vibrate option. (default – disabled).
• Fixed Dialing Numbers - Use Fixed Dialing to restrict the device to dial only the phone number(s) or area
code(s) specified in a Fixed Dialing list.
• Wi-Fi Calling - Enable the TC25 to route calls via Wi-Fi networks or carrier’s network, depending upon
preference and signal strength. Check with your carrier first.
• GSM call settings
• Call forwarding - Use call forwarding to forward incoming calls to a different phone number.
IMPORTANT: Call Forwarding may not be available on all networks. Check with the service provider for
availability.
• Additional settings
• Caller ID - Enable caller ID to reveal the identity of the person making an outgoing call. Options:
Network default (default), Hide number, Show number.
• Call waiting - set to be notified of an incoming call while on a call.
• Call barring - Use call barring to block certain types of incoming and/or outgoing calls. Select the type of
incoming and/or outgoing calls to block.
Call Blocking
If you don’t want to get calls from a certain phone number, you can block it. When the number tries to call you, your
phone declines the call automatically.
Touch ADD NUMBER to add phone number that you want to block.
66
Page 67
Accessibility
• TTY mode - Touch to set the TTY setting. Use an optional teletypewriter (TTY) device with the TC25 to
send and receive calls. Plug the TTY device into an adapter and into the TC25 USB C port and set the
TC25 to operate in one of the TTY modes.
IMPORTANT: Use a TSB-121 compliant cable (provided by the TTY manufacturer) to connect the TTY device to the
TC25.
Set the TC25 volume to a middle level setting for proper operation. If you experience a high number of
incorrect characters, adjust the volume as needed to minimize the error rate.
For optimal performance, the TC25 should be at least 30 cm (12 inches) from the TTY device. Placing the
TC25 too close to the TTY device may cause high error rates.
• TTY off - TTY is off (default).
• TTY Full - Transmit and receive TTY characters.
• TTY HCO - Transmit TTY characters but receive by listening to earpiece.
• TTY VCO - Receive TTY characters but transmit by speaking into microphone.
• Hearing aids - Turn on or off hearing aid compatibility.
Calls
67
Page 68
Applications
This section describes the applications installed on the device.
File Browser
Use the File Browser application to view and mange files on the device.
Swipe up from the bottom of the Home screen and touch .
Figure 60 File Browser Screen
The address bar indicates the current folder path. Touch the current folder path to manually enter a path and folder
name.
Use to select multiple files/folder.
Use to view the device root folder.
Use to view internal storage folder.
Use to view the previous folder or to exit the application.
Touch and hold an item to perform an operation on that item. Select one of the options from the File Operations
menu:
• Information - View detailed information about the file or folder.
• Move - Move the file or folder to a new location.
68
Page 69
Applications
• Copy - Copy the select file.
• Delete - Delete the selected file.
• Rename - Rename the select file.
• Open as - Open the selected file as a specific file type.
• Share - Share the file with other devices.
Touch to open menu options:
• New Folder - Create a new folder.
• Search - Search for a specific file on the device.
• Sort - Select the sort order of the files by name, type, size or date.
• Refresh - Refresh the current folder.
• List View - Change the folder to display item is a list. Appears only in Grid view.
• Grid View - Change the folder to display item is a grid. Appears only in List view.
• Change Size - Change the size of the icons.
• About File Browser - Displays the app version.
69
Page 70
Messaging
Use Messaging to send and receive SMS and MMS messages. From a Home or All Apps screen, touch .
Sending a Text Message
1. In the main Messaging screen, touch .
Figure 61 New Text Message Screen
Applications
2. In the To field, enter a name or a mobile phone number.
3. In the Send message field, enter the text message.
The 160-character limit counter indicates how many characters are left. If it goes over that limit, a new
message is created, which is joined with its predecessors when received.
If the user presses the Back button while composing a message, it’s saved as a draft in the Messaging screen.
Touch the conversation to resume composing it.
4. Touch to send the message.
Sending a Multimedia Message
1. In the main Messaging screen, touch .
2. In the To field, enter a name or a mobile phone number.
3. Touch to attach the media file of your choice:
70
Page 71
Applications
Figure 62 New Multimedia Message Screen
• Subject - Add a subject for the message.
• Pictures - Select a picture to attach.
• Capture picture - Camera opens to take a picture and attach it.
• Videos - Select a video to attach.
• Capture video - Camcorder opens to record a video and attach it to the message.
• Audio - Choose a sound file to attach.
• Record audio - Sound Recorder opens to record a spoken message and attach it to the message.
• Slideshow - Opens a screen to assemble text, photos, videos, and recordings into a slideshow of up to 10
slides to attach to the message.
• Insert contact info - Send a contact’s phone information as text.
• Contact vCard - Send a contact’s information as a vCard.
• Import Template - Send a pre-defined message.
• Calendar - Send a calendar event.
4. Touch to send the message.
71
Page 72
Contacts
Use the Contacts application to manage contacts.
From a Home or Apps screen, touch . People opens to the main list of contacts. View contacts in three ways at
the top of the screen: Groups, All contacts, and Favorites. Touch the tabs to change how to view the contacts.
Swipe up or down to scroll through the lists.
Figure 63 Contacts Screen
Applications
Adding a Contact
1. In the Contacts application, touch .
2. If there are more than one account with contacts, touch the one to use.
3. Type the contact’s name and other information. Touch a field to start typing, and swipe down to view all
categories.
4. To open a menu with preset labels, such as Home or Work for an email address, touch the label to the right of
the item of contact information. Or, to create your own label, touch Custom in the menu.
5. Touch .
Editing Contacts
1. In the Contacts application, touch a contact name to edit.
2. Touch .
3. Edit the contact information.
4. Touch .
Deleting Contacts
1. In the Contacts application, touch a contact name to delete.
2. Touch .
3. Touch Delete.
72
Page 73
4. Touch Delete to confirm.
Applications
73
Page 74
Camera
Camera Mode
Settings
Beautification
Scene Mode
Shutter Button
Gallery
Apply Filters
This section provides information for taking photos and recording videos using the integrated digital cameras.
Taking Photos
1. Swipe up from the bottom of the Home screen and touch .
Figure 64 Camera Mode
Applications
IMPORTANT Camera application is available only on configurations with cameras.
NOTE If a microSD card is installed, The TC25 saves photos and videos on the microSD card. If a microSD card
is not installed, the TC25 saves photos and videos on the internal storage.
NOTE Camera settings are described in Photo Settings on page 76.
2. If necessary, touch the Camera Mode icon and touch .
3. Frame the subject on the screen.
4. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on
the screen.
5. Touch an area on the screen to focus. The focus circle appears on the screen. The two bars turn green when
in focus.
6. Touch .
The camera takes a photo and a shutter sound plays.
The photo momentarily displays as a thumbnail in the lower left corner.
74
Page 75
Applications
Taking a Panoramic Photo
Panorama mode lets the user create a single wide image by panning slowly across a scene.
1. Swipe up from the bottom of the Home screen and touch .
2. Touch the Camera Mode and touch .
Figure 65 Panoramic Mode
3. Frame one side of the scene to capture.
4. Touch and slowly start panning across the area to capture. A small white square appears inside the button
indicating the capture is in progress.
If panning too quickly, the message Too fast appears.
5. Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves
the image.
Recording Videos
To record a video:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch the Camera Mode and touch .
75
Page 76
Figure 66 Video Mode
Camera Mode
Settings
Audio
Shutter Button
Gallery
Applications
3. Point the camera and frame the scene.
4. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on
the screen.
5. Touch to start recording.
The device starts recording the video. The video time remaining appears in the top left of the screen.
6. Touch to end recording.
The video momentarily displays as a thumbnail in the lower left corner.
Photo Settings
When in Photo mode, photo settings are displayed on screen. Touch to display the photo settings options.
• Flash - Touch to set whether the camera relies on its light meter to decide whether a flash is necessary, or
to turn it on or off for all shots.
• Off - Disable flash.
• Auto - Camera adjusts flash automatically depending upon light meter (default).
• On - Enable flash upon taking a photo.
• Picture size - Touch to set the size (in pixels) of the photo. Options: 8M pixels (default), 5M pixels, 4M
pixels (16:9), 3M pixels, HD 1080, 2M pixels, 1.5M pixels, 1.3M pixels, WXGA, HD 720, 1M pixels,
SVGA, WVGA, 720 x 480, VGA, CIF or QVGA.
• Picture quality - Touch to select picture quality setting. Options: Low, Standard (default) or High.
• Countdown timer - Select amount of time after pressing the camera button that the photo is taken.
Options: Off (default), 2 seconds, 5 seconds or 10 seconds.
• Storage – Touch to select location to store the photo. Options: Phone (default) or SD Card.
• Continuous Shot - Select to take a series of photos quickly while holding the capture button. Options: Off
(default) or On.
76
Page 77
Applications
• Face Detection - Select to enable face detection. Options: Off (default) or On.
• ZSL - Set the camera to immediately take a picture when the button is pressed (default – enabled)
• Focus mode - Disabled.
• Anti Banding - Select to prevent the appearance of vertical or horizontal lines (banding) when
photographing images on TV and monitor screens. Options: Off (default), 50 Hz, 60 Hz, or Auto.
• ISO - Set how sensitive the camera is to light. Options: Auto (default), ISO Auto (HJR), ISO100, ISO200,
ISO400, ISO800 or ISO1600.
• Exposure - Touch to adjust the exposure settings. Options: +2, +1, 0(default), -1 or -2.
• White balance - Touch to select how Camera adjusts colors in different kinds of light, to achieve the most
natural-looking colors.
• Incandescent - Adjust the white balance for incandescent lighting.
• Fluorescent - Adjust the white balance for florescent lighting.
• Auto - Adjust the white balance automatically (default).
• Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Chroma Flash - Select to simultaneously take a flash and a non-flash version of the same subject and
combine these two images to improve the quality of flash photography. Options: Off (default) or On.
• Redeye Reduction - Select to reduce the red-eye phenomenon when using the flash. Options: Disable
(default) or Enable. Disabled when Chroma Flash is enabled.
• Shutter Sound - Select to play a shutter sound when taking a photo. Options: Disable (default) or Enable.
Video Settings
When in Video mode, video settings are displayed on screen. Touch to display the video settings options.
• Flash - Touch to set whether Rear-facing Camera relies on its light meter to decide whether a flash is
necessary, or to turn it on or off for all shots.
• Off - Disable flash (default).
• On - Enable flash.
• Video quality - Touch to select video quality. Options: HD 1080p (default), HD 720p, SD 480p, VGA, CIF,
or QVGA.
• GPS location - Include location information with each photo using the device global positioning system
(GPS). Options: On (default) or Off.
• Video duration - Options: 30 seconds (MMS), 10 minutes (default), 30 minutes or no limit.
• Storage – Touch to select location to store the photo. Options: Phone (default) or SD Card.
77
Page 78
Applications
• White balance - Touch to select how Camera adjusts colors in different kinds of light, to achieve the most
natural-looking colors.
• Incandescent - Adjust the white balance for incandescent lighting.
• Fluorescent - Adjust the white balance for florescent lighting.
• Auto - Adjust the white balance automatically (default).
• Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Video High FrameRate - Select a high frame rate for videos to capture movement more clearly. Options:
Off (default), HFR 60, HFR 90, HFR 120, HSR 60, HSR 90, or HSR 120.
• Image Stabilization - Select to help stabilize zoom while shooting video. Options: Off (default), or On.
78
Page 79
Photos
Use Photos to:
Photos presents all photos and videos stored on the microSD card and internal memory.
To open the Photos application, swipe up from the bottom of the Home screen and touch .
By default, Photos open to the Photos view.
Figure 67 Photos View
Applications
• view photos
• play videos
• perform basic editing of photos
• set photos as wallpaper
• set photos as a contact photo
• share photos and videos.
Touch Albums to view photos sorted by albums.
79
Page 80
Applications
Figure 68 Albums View
• Touch an album to open it and view its contents. The photos and videos in the album display in
chronological order.
• Touch a photo or video in an album to view it.
• Touch to return to the main screen.
Working with Albums
Albums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in
a chronologically ordered grid. The name of the album displays at the top of the screen.
Figure 69 Photos Inside an Album
Swipe up to scroll images across the screen.
Deleting an Album
To delete an album and its contents:
1. Touch an album to open it.
80
Page 81
Applications
2. Touch > Delete device folder.
3. In the delete folder dialog box, touch Delete.
Working with Photos
Use Photos to view photos on the internal memory and the microSD card.
Viewing and Browsing Photos
To view a photo:
1. Touch an album to open it.
2. Touch a photo.
Figure 70 Photo Example
3. Swipe left or right to view the next or previous photo in the album.
4. Turn the device to view the photo in upright (portrait) or sideways (landscape) orientation. The photo is
displayed (but not saved) in the new orientation.
5. Touch the photo to view the controls.
6. Pinch two fingers together or spread them apart to zoom in or out.
7. Drag the photo to view parts that are not in view.
Cropping a Photo
1. Touch a photo to view the controls.
2. Touch > . The cropping tool appears.
81
Page 82
Applications
Figure 71 Cropping Tool
3. Use the cropping tool to select the portion of the photo to crop.
• Drag from the inside of the cropping tool to move it.
• Drag an edge of the cropping tool to resize it to any proportion.
4. Touch DONE.
5. Touch SAVE to save a copy of the cropped photo. The original version is retained.
Setting a Photo as a Contact Icon
1. Touch the photo to open it.
2. Touch .
3. Touch Use as.
4. Touch Contact photo.
5. In the Contacts application, touch a contact.
6. Touch the white box and crop the photo accordingly.
7. Touch Done.
Share a Photo
1. Touch an album to open it.
2. Touch a photo to open it.
3. Touch .
4. Select additional photos, if required.
5. Touch a contact or application to use to share the selected photo. The application selected opens with the
photo attached to a new message.
Deleting a Photo
1. Touch a photo to open it.
2. Touch .
3. Touch Move to Trash to delete the photo.
82
Page 83
Applications
Working with Videos
Use Photos to view videos and share videos.
Watching Videos
1. Touch an album to open it.
2. Touch a video. The video automatically start playing.
3. Touch the screen to view the playback controls.
Sharing a Video
1. Touch an album to open it.
2. Touch a video to open it.
3. Touch . The Share menu appears.
4. Touch the application to use to share the selected video. The application selected opens with the video
attached to a new message.
Deleting a Video
1. Touch an album to open it.
2. Touch a video to open it.
3. Touch .
4. Touch Move to trash.
83
Page 84
DataWedge Demonstration
NOTE See the TC25 Rugged Smartphone Integrator Guide for Android Version 7.1.2 for information on DataWedge
configuration.
Use DataWedge Demonstration to demonstrate data capture functionality.
Figure 72 DataWedge Demonstration Window
Applications
Table 9 DataWedge Demonstration Icons
Feature Icon Description
Illumination
Data Capture Indicates that the data capture function is through the internal imager.
Scan Mode Indicates imager is in picklist mode. Touch to change to normal scan
Menu Opens a menu to view the application information or to set the
Indicates imager illumination is off. Touch to turn illumination on.
Indicates imager illumination is on. Touch to turn illumination off.
Indicates that a Bluetooth imager is not connected to the TC25.
Indicates that a Bluetooth imager is connected to the TC25.
mode.
Indicates imager is in normal scan mode. Touch to change to picklist
mode.
application DataWedge profile.
Touch the Data Capture icon to select the data capture mode.
84
Page 85
Applications
Figure 73 Data Capture Options Menu
Select a scanner to use. See Data Capture for configuring scanner options.
Either press the programmable button or touch the yellow scan button to enable data capture. The captured data
appears in the text field below the yellow button.
85
Page 86
Sound Recorder
Use Sound Recorder to record audio messages.
To open the Sound Recorder application, swipe up from the bottom of the Home screen and touch .
Recordings are saved on the microSD card (if installed) or the Internal Storage and available in the Music
application playlist titled “Audio Recordings.”
Figure 74 Sound Recorder Application
Applications
86
Page 87
PTT Express Voice Client
Talk Group
Service Indication
Notification Icon
Settings
Enable/Disable Switch
NOTE PTT Express Voice Client creates Push-To-Talk (PTT) communication capability between disparate enterprise
devices. Leveraging existing Wireless Local Area Network (WLAN) infrastructure, PTT Express delivers simple
PTT communication without the need of a voice communication server.
• Group Call: Press and hold the PTT button to start communicating with other voice client users.
• Private Response: Double-press and the PTT button to respond to the originator of the last broadcast or
to make a Private Response.
PTT Audible Indicators
The following tones provide helpful cues when using the voice client.
• Talk Tone: Double chirp. Plays when the Talk button is depressed. This is a prompt for the user to start
talking.
• Access Tone: Single beep. Plays when another user just finished a broadcast or response. The user is
now able to initiate a Group Broadcast or Private Response.
• Busy Tone: Continuous tone. Plays when the Talk button is depressed and another user is already
communicating on the same talkgroup. Plays after the maximum allowed talk time is reached (60
seconds).
• Network Tone:
Applications
• Three increasing pitch beeps. Plays when PTT Express has acquired the WLAN connection and the
service is enabled.
• Three decreasing pitch beeps. Plays when PTT Express has lost the WLAN connection or the service
is disabled.
Figure 75 PTT Express Default User Interface
87
Page 88
Applications
Table 10 PTT Express Default User Interface Descriptions
Item Description
Notification Icon Indicates the current state of the PTT Express client.
Service Indication Indicates the status of the PTT Express client. Options: Service Enabled, Service
Disabled or Service Unavailable.
Talk Groups Lists all 32 Talk Groups available for PTT communication.
Settings Opens the PTT Express Settings screen.
Enable/Disable
Switch
Turns the PTT service on and off.
Notification Icons
Indicates the current state of the PTT Express Voice client.
Table 11 PTT Express Default User Interface Descriptions
Status Icon Description
Indicates that PTT Express Voice client is disabled.
Indicates that PTT Express Voice client is enabled but not connected to a WLAN.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and listening on the
Talk Group indicated by the number next to the icon.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and communicating
on the Talk Group indicated by the number next to the icon.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and in a private
response.
Indicates that PTT Express Voice client is enabled and muted.
Indicates that the PTT Express Voice client is enabled but it is not able to communicate due to
a VoIP telephony call is in progress.
Enabling PTT Communication
1. Swipe up from the bottom of the Home screen and touch .
2. Slide the Enable/Disable Switch to the ON position. The button changes to an ON button.
88
Page 89
Applications
PTT Button
Selecting a Talk Group
One of 32 Talk Groups can be selected by PTT Express users. However, only one talk group may be enabled at a
time on the device. Touch one of the 32 Talk Groups. The selected Talk Group is highlighted.
PTT Communication
NOTE This section describes the default PTT Express client configuration. See the PTT Express V1.2 User
Guide for detailed information on using the client.
PTT communication may be established as a Group Call. When PTT Express is enabled, the PTT button on the left
side of the device is assigned for PTT communication.
Figure 76 PTT Buttons
Creating a Group Call
1. Press and hold the PTT button and listen for the talk tone to play.
If a busy tone is heard, release the button and wait a moment before making another attempt. Ensure that PTT
Express and the WLAN are enabled.
2. Start talking after the talk tone is heard.
NOTE If the user holds the button for more than 60 seconds (default), the call is dropped allowing others to make
Group calls. The user should release the button when finished talking to allow others to make calls.
3. Release the button when finished talking.
Responding with a Private Response
The Private Response can only be initiated once a Group Call has been established. The initial Private Response
is made to the originator of the Group Call.
1. Wait until an access tone is heard.
2. Within 10 seconds, double-press the PTT button, and listen for the talk tone to play.
3. If a busy tone is heard, release the button and wait a moment before making another attempt. Ensure that PTT
Express and the WLAN are enabled.
4. Start talking after the talk tone plays.
5. Release the button when finished talking.
Disabling PTT Express Voice Client Communication
1. Swipe up from the bottom of the Home screen and touch .
89
Page 90
Applications
2. Slide the Enable/Disable Switch to the OFF position. The button changes to OFF.
3. Touch .
90
Page 91
RxLogger
RxLogger is a comprehensive diagnostic tool that provides application and system metrics. It allows for custom
plug-ins to be created and work seamlessly with this tool. RxLogger is used to diagnose device and application
issues. Its information tracking includes the following: CPU load, memory load, memory snapshots, battery
consumption, power states, wireless logging, cellular logging, TCP dumps, Bluetooth logging, GPS logging, logcat,
FTP push/pull, ANR dumps, etc. All logs and files generated are saved onto flash storage on the device (internal or
external).
Figure 77 RxLogger
Applications
Enabling Logging
To enable RxLogger:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch START. RxLogger begins collecting data.
3. Touch .
Disabling Logging
To disable RxLogger:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch STOP. RxLogger stops collecting data.
3. Touch .
91
Page 92
RxLogger Utility
RxLogger Utility is a data monitoring application for viewing logs in the TC25 while RxLogger is running. The user
can access the logs and RxLogger Utility features in the App View or the Overlay View.
In the App View the user views logs in the RxLogger Utility.
Figure 78 RxLogger Utility App View
Applications
Refer to the TC25 Rugged Smartphone Integrator Guide for detailed information about using RxLogger Utility.
92
Page 93
Diagnostic Tool
The Diagnostic Tool is a utility that determines the health of the TC25. Use the Diagnostic Tool to troubleshooting
the device and determine issues.
1. Swipe up from the bottom of the Home screen and touch .
Figure 79 Diagnostic Tool
Applications
2. Touch Run Test. The app tests all enabled subsystems (by default only the Battery and System tests are
enabled). See Settings on page 95 to enable subsystem tests.
Figure 80 Test Passed Screen
93
Page 94
Applications
Figure 81 Test Failed Screen
3. To view each individual subsystem test, touch Subsystem Tests.
Figure 82 Subsystem Screen
Table 12 Subsystem Test Result Indicators
Status Icon Description
Indicates test passed.
Indicates test failed.
Indicates test not supported or not enabled.
4. Touch one of the subsystems to view details.
94
Page 95
Applications
Figure 83 Battery Subsystem Details
Settings
By default only the Battery and System tests are enabled. To enable other tests:
1. Touch > Settings.
2. Touch to the left of the test name. A green box with a checkmark appears.
3. Touch SAVE.
4. Touch Yes to confirm.
5. Touch .
Battery Test Information
The Battery Test obtains the following information:
• Battery Level - Indicates the current battery charge level.
• Battery Voltage - Indicates the current battery voltage.
• Status - Indicates if the battery is charging (on AC power) or discharging (on battery power).
• Power Source - Indicates whether the device is receiving power from the battery or from an external
source.
• Temperature - Indicates the current battery temperature.
• Charge Cycles - Not applicable.
• Backup Battery Voltage - Indicates backup battery voltage.
• Manufacture Date - Displays the manufacture date of the battery.
GPS Test Information
The GPS Test obtains the following information:
• GPS Provider Enabled - Indicates if GPS is enabled (true) or disabled (false).
• Latitude - Indicates current latitude position.
• Longitude - Indicates current longitude position.
• Altitude - Indicates current altitude in meters.
95
Page 96
Applications
• Bearing - Indicates current bearing.
• Speed - Indicates speed in meters per second.
• Accuracy - Indicates GPS accuracy in meters.
System Test Information
Use the System Test to determine if the CPU or memory loads are too high, there are too many processes running
on the device, or that storage on the device is almost full. The System Test obtains the following information:
• CPU Load - Indicates the amount of CPU being used.
• Free Physical Memory - Indicates the amount of RAM available.
• Free Storage - Indicates the amount of internal Flash memory available.
• Process Count - Indicates the number of processes currently running.
WLAN Test Information
If the WiFi radio is not present or disabled the test may be skipped. Use this information to determine if the device’s
WLAN configuration is correct or whether there is any connection with an access point or network. The WLAN Test
obtains the following information:
• WLAN Enabled - Indicates if the WLAN radio is enabled or disabled.
• WLAN Status - Indicates the current status of association with the access point.
• ESSID - Displays the name of the wireless network.
• BSSID - Displays the MAC address of the connected access point.
• MAC Address - Displays the device’s MAC address.
• Signal - Indicates the strength of the Wi-Fi signal (in dBm).
• IP Address - Displays the IP address of the device.
WWAN Test Information
The WWAN Test obtains the following information:
• SIM State - Displays the current state of the SIM card.
• WAN Type - Displays the data connection type.
• Signal Strength - Displays the current cellular signal strength.
• Phone Number - Displays the phone number assigned to the device.
• Device ID - Displays the device ID number.
Bluetooth Test Information
The Bluetooth Test obtains the following information:
• Enabled - Indicates if the Bluetooth radio is enabled or disabled.
• Status - Indicates if the device is paired to another Bluetooth device.
• Connectable/Discoverable - Indicates if the device is discoverable or connectable.
• Address - Displays the Bluetooth radio MAC address.
• Name - Displays the Bluetooth name for the device.
96
Page 97
Data Capture
The TC25 supports data capture using:
• integrated imager
• SE4710 scan engine
• SE2100 scan engine
• RS507 Hands-free Imager
• RS6000 Bluetooth Ring Scanner.
IMPORTANT To determine the integrated scan engine in the device, go to Settings > About phone >
Hardware components > Scanner.
Imaging
The TC25 with an integrated 2D imager has the following features:
• Omni-directional reading of a variety of barcode symbologies, including the most popular linear, postal,
PDF417, and 2D matrix code types.
• The ability to capture and download images to a host for a variety of imaging applications.
• Advanced intuitive laser aiming cross-hair and dot aiming for easy point-and-shoot operation.
The imager uses imaging technology to take a picture of a barcode, stores the resulting image in its memory, and
executes state-of-the-art software decoding algorithms to extract the barcode data from the image.
Operational Modes
The TC25 with an integrated imager supports two modes of operation, listed below. Activate each mode by
pressing the Scan button.
• Decode Mode: In this mode, the TC25 attempts to locate and decode enabled barcodes within its field of
view. The imager remains in this mode as long as the user holds the scan button, or until it decodes a
barcode.
NOTE To enable Pick List Mode, configure in DataWedge or set in an application using a API command.
• Pick List Mode: This mode allows the user to selectively decode a barcode when more than one barcode
is in the TC25’s field of view. To accomplish this, move the aiming cross-hair or dot over the required
97
Page 98
Data Capture
barcode to decode only this barcode. This feature is ideal for pick lists containing multiple barcodes and
manufacturing or transport labels containing more than one barcode type (either 1D or 2D).
NOTE To enable Basic MultiBarcode Mode, configure in DataWedge or set in an application using a API
command.
• Basic MultiBarcode Mode: In this mode, the TC25 attempts to locate and decode a specific number of
unique barcodes within its field of view. The TC25 remains in this mode as long as the user holds the scan
button, or until it decodes all the barcodes. Available on integrated SE2100 or SE4710 imagers only.
• The TC25 attempts to scan the programmed number of unique barcodes (from 2 through 10).
• If there are duplicate barcodes (same symbology type and data), only one of the duplicate barcodes is
decoded and the remainder are ignored. If the label has two duplicate barcodes plus another two
different barcodes, a maximum of three barcodes will be decoded from that label; one will be ignored
as a duplicate.
• Barcodes can be of multiple symbology types and still be acquired together. For example, if the
specified quantity for a Basic MultiBarcode scan is four, two barcodes can be symbology type Code
128 and the other two can be symbology type Code 39.
• If the specified number of unique barcodes is not initially in view of the TC25, the TC25 will not decode
any data until the device is moved to capture the additional barcode(s) or time out occurs. If the TC25
field of view contains a number of barcodes greater than the specified quantity, the TC25 randomly
decodes barcode(s) until the specified number of unique barcodes is reached. For example, if the
count is set to two and eight barcodes are in the field of view, the TC25 decodes the first two unique
barcodes it sees, returning the data in random order.
• Basic MultiBarcode Mode does not support concatenated barcodes.
RS507 Hands-Free Imager
The RS507 Hands-free Imager is a wearable barcode scan solution for both 1D and 2D barcode symbologies.
Figure 84 RS507 Hands-Free Imager
See to the RS507 Hands-free Imager Product Reference Guide for more information.
RS6000 Bluetooth Ring Scanner
The RS6000 Bluetooth Ring Scanner is a wearable barcode scan solution for both 1D and 2D barcode
symbologies.
98
Page 99
Figure 85 RS6000 Bluetooth Ring Scanner
See to the RS6000 Bluetooth Ring Scanner Product Reference Guide for more information.
Scanning Considerations
Typically, scanning is a simple matter of aim, scan, and decode and a few quick trial efforts master it. However,
consider the following to optimize scanning performance:
Data Capture
• Range: Any scanning device decodes well over a particular working range — minimum and maximum
distances from the barcode. This range varies according to barcode density and scanning device optics.
Scanning within range brings quick and constant decodes; scanning too close or too far away prevents
decodes. Move the scanner closer and further away to find the right working range for the barcodes being
scanned.
• Angle: Scanning angle is important for promoting quick decodes. When laser beams reflect directly back
into the scanner from the barcode, this specular reflection can “blind” the scanner. To avoid this, scan the
barcode so that the beam does not bounce directly back. But don’t scan at too sharp an angle; the scanner
needs to collect scattered reflections from the scan to make a successful decode. Practice quickly shows
what tolerances to work within.
• Hold the TC25 farther away for larger symbols
• Move the TC25 closer for symbols with bars that are close together.
NOTE Scanning procedures depend on the application and TC25 configuration. An application may use different
scanning procedures from the one listed above.
Barcode Scanning with Internal SE2100 Imager
To read a barcode, a scan-enabled application is required. The TC25 contains the DataWedge application that
allows the user to enable the imager, decode the barcode data and display the barcode content.
1. Ensure that an application is open on the TC25 and a text field is in focus (text cursor in text field).
2. Point the exit window on the top of the TC25 at a barcode.
99
Page 100
Data Capture
Figure 86 SE2100 Imager Scanning
3. Press and hold the scan button.
The white aiming pattern turns on to assist in aiming.
4. Ensure the barcode is within the area formed by the aiming pattern.
Figure 87 SE2100 Aiming Pattern
5. The Data Capture LED lights green and a beep sounds, by default, to indicate the barcode was decoded
successfully.
6. Release the scan button.
NOTE Imager decoding usually occurs instantaneously. The TC25 repeats the steps required to take a digital
picture (image) of a poor or difficult barcode as long as the scan button remains pressed.
7. The barcode content data displays in the text field.
SE2100 Picklist Mode
When Picklist Mode is enabled, the screen displays an image of the barcode and a red cross-hair. See TC25
Rugged Smartphone Integrator Guide for Android Version 7.1.2 for information on setting Picklist Mode.
When the TC25 is in Picklist Mode, the imager does not decode the barcode until the cross-hair touches the
barcode.
100
Loading...