Rack Mounting Bracket
Screw
Mounting Tab Mounting Slot
Installation Guide
Install Power Supply Bracket
1. Align the power supply bracket with the mounting screw
hole on the rack mount bracket.
2. Secure the power supply bracket to the rack mount bracket
using the provided screw.
Power Supply Bracket
Rack Mount Bracket
Top Product
MC9500 Battery
Charger
MC9500 Battery
Charger
Bottom
Product
MC9500 Four
Bay Cradle
MC9500 Battery
Charger
Spacing Between Brackets
U Sizes Inches
2U 3.5”
1U 1.75”
1U
(1.75”)
Four Bay Cradle Mounting
To mount a Four Bay Ethernet or Charge Only cradle:
1. Align the mountin
mounting tabs on the rack mount bracket.
g slots on the back of the cradle with the
Zebra reserves the right to make changes to any product to improve reliability,
function, or design.
Zebra does not assume any product liability arising out of, or in connection
with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Zebra products
might be used. An implied license exists only for equipment, circuits, and
subsystems contained in Zebra products.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Install Rack Mount Bracket
To install the rack mount bracket onto the rack:
NOTE Use screws provided with rack system. Refer to
rack user documentation for instructions.
When installing on a new rack start at the
bottom of the rack and work up. The bottom of
the first rack mount bracket should be at least
8U from the bottom of the rack.
1. Align the screw holes on the rack mount bracket with the
screw holes on the rack rails. Most racks include U marks
on the rails for proper positioning of the brackets.
2. Secure the rack mount bracket to the rails using four
screws.
3U
(5.25”)
8U (14.0”) from
bottom of rack
Power Connection
To connect power to the cradle or charger:
1. Place the power supply onto the power supply bracket as
shown. Ensure that the power supply is oriented with the
AC input facing to the right.
Power Supply
AC Input
2. Secure the cradle to the rack mount bracket using the two
thumb screws.
Thumb Screw (2)
Four Bay Cradle Connection
To connect the cables to a Four Bay Ethernet or Charge Only
cradle:
1. Connect the DC power cord to the cradle power port.
Power Port
Ethernet Port 2
Ethernet Port 1
Service Information
If you have a problem with your equipment, contact your facility’s Technical or
Systems Support. If there is a problem with the equipment, they will contact the
Zebra Support Center.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp.
The Symbol logo is a registered trademark of Symbol Technologies, Inc.,
a Zebra Technologies company.
© 2015 Symbol Technologies, Inc.
72-136166-02 Revision A — February 2015
3. Repeat the procedure for each rack mount bracket.
4. Ensure the proper spacing between rack mount brackets.
Bracket Spacing
The spacing between rack mount brackets vary depending
upon the devices mounted on the rack. The table below lists
the spacing required between the rack mount brackets with
different configurations.
Top Product
MC9500 Four
Bay Cradle
MC9500 Four
Bay Cradle
Bottom
Product
MC9500 Four
Bay Cradle
MC9500 Battery
Charger
Spacing Between Brackets
U Sizes Inches
3U 5.25”
2U 3.5”
1 2 3
2. Connect the AC line cord to the power supply.
3. Connect the DC power cord to the power supply.
DC Power Cord
AC Line Cord
DC Power Cable
Ethernet Cable
2. For Ethernet cradle, connect an Ethernet cable to the
Ethernet port on the cradle.
3. Connect the other end of the Ethernet cable to another
Ethernet cradle or to an Ethernet switch.
Four Slot Battery Charger Mounting
AC Line CordDC Power Cable
Screw Holes
To mount the Four Slot Battery Charger:
1. Align the mounting slots on the back of each charger with
the mounting slots on the rack mount bracket.
Mounting Tab
2. Secure the chargers to the rack mount bracket using the
thumb screws.
Mounting Slot
2. Connect each power plug to the power port on the back of
the chargers.
Cable Routing and Management
While installing the brackets, power supplies and cables:
• Use tie wraps to secure cables to the bracket
• Coil cables wherever possible.
• Route power cables along the rails.
• Route inter-cradle cables to the side rails and then from
the rails to the bracket.
and rails.
Power Connection
CAUTION Installer should ensure that all building codes
are followed when connecting the power
supplies to an AC power source.
Finishing
After the rack installation is complete, use blank panels to
close up spacing between rack mount brackets. Blank panels
are available from the rack manufacturer and come in various
U sizes.
Thumb Screw
Four Slot Charger Connection
To connect the cables to the Four Slot Battery Chargers:
NOTE Use one power supply for up to four Four Slot
Battery Chargers.
1. Connect the DC power cord to the power supply output
connector.
Mounting an MC3000, MC7X or MC55
4-slot Cradle Using the Wall Mount
Bracket
An optional wall mount bracket is available to mount an
MC3000, MC7X or MC55 cradle to the rack mount bracket.
Refer to the instructions provided with the bracket.
Use the four scre
onto the rack mount bracket.
ws holes to mount the wall mount bracket
Screw Holes
5 6 74
Loading...