MC93XX
Mobile Computer
Quick Start Guide
MN-003413-03 Rev. A
Copyright
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many
jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2020 Zebra
Technologies Corporation and/or its affiliates. All rights reserved.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to
www.zebra.com/copyright
MC93XX Quick Start Guide
.
WARRANTY: For complete warranty information, go to www.zebra.com/warranty
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula
Terms of Use
• Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries (“Zebra
Technologies”). It is intended solely for the information and use of parties operating and maintaining the
equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any
other parties for any other purpose without the express, written permission of Zebra Technologies.
• Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are
subject to change without notice.
• Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are
correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and
disclaims liability resulting therefrom.
• Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the
accompanying product (including hardware and software) be liable for any damages whatsoever (including,
without limitation, consequential damages including loss of business profits, business interruption, or loss of
business information) arising out of the use of, the results of use of, or inability to use such product, even if
Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.
.
.
Warranty
For the complete Zebra hardware product warranty statement, go to www.zebra.com/warranty.
Service Information
Before you use the unit, it must be configured to operate in your facility’s network and run your applications.
If you have a problem running your unit or using your equipment, contact your facility’s Technical or Systems
Support. If there is a problem with the equipment, they will contact the Zebra Global Customer Support at
www.zebra.com/support
For the latest version of this guide go to www.zebra.com/support
.
.
2
MC93XX Quick Start Guide
Provide Documentation Feedback
If you have comments, questions, or suggestions about this guide, send an email to EVM-Techdocs@zebra.com.
Configurations
MC93XX used in this guide refers to the MC93XX-G mobile computer with scan trigger. This guide applies to the
following Model Numbers: MC930B, MC930P.
Unpacking
Carefully remove all protective material from the device and save the shipping container for later storage and
shipping.
Verify the following items are in the box:
• Device
• Lithium-ion battery
• Regulatory Guide.
Inspect the equipment for damage. If any equipment is missing or damaged, contact the Zebra Support Center
immediately.
3
Device Features
Figure 1 MC93XX Front View
1
2
MC93XX Quick Start Guide
13
12
11
10
3
4
5
6
7
Table 1 MC93XX Features - Front View
Number Item Function
1 Ambient Light
Controls display and keyboard backlight.
Sensor
2 Front Facing
Use to take photos and videos.
Camera
NOTE: The front camera is available only on the premium configurations.
3 Display Displays all information needed to operate the device.
4 Speaker Side
Provides audio output for video and music playback.
Port
5 Trigger Initiates data capture when a scan application is enabled.
6 P1 - Dedicated
Initiates push-to-talk communications (programmable).
PTT Key
7 Battery Release
Releases the battery from the device.
Latch
NOTE: To release the battery, simultaneously press the battery release latches
on both the sides of the device.
9
8
4
MC93XX Quick Start Guide
Table 1 MC93XX Features - Front View (continued)
Number Item Function
8 Battery Provides power for operating the device.
9 Microphone Use for communications in Handset mode.
10 Keypad Use to enter data and navigate on screen functions.
11 Power Button Press and hold to turn on the device. Press to turn on or off the screen.
Press and hold to select one of these options:
Power off - Turn off the device.
Restart - Restart the device when software stops responding.
12 Center Scan
Button
13 Charger/Decode
Status LED
Figure 2 MC93XX Back View
Initiates data capture when a scan application is enabled.
Indicates battery charging status while charging, app generated
notifications, and data capture status.
15
14
16
20
19
18
17
5
MC93XX Quick Start Guide
Table 2 MC93XX Features - Back View
Number Item Function
14
Passive NFC Tag
(Inside the battery
compartment.)
Provides secondary product label information (configuration, serial
number and manufacture data code) in the event that the readable
product label is worn or missing.
15 Battery Release
Releases the battery from the device.
Latch
16 Side Speaker Port Provides audio output for video and music playback.
17 Scanner Exit
Provides data capture using the scanner/imager.
Window
18 Camera Flash Provides illumination for the camera.
NOTE: Camera is available only on some configurations.
19 NFC Antenna Provides communication with other NFC-enabled devices.
NOTE: NFC antenna is available only on the premium configurations.
20 Rear Camera Takes photos and videos.
NOTE: The rear camera is available only on the premium configurations.
6
Setup
To start using the device for the first time:
• Install a microSD card (optional)
• Install the battery
• Charge the device
• Power on the device.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the keypad module.
Refer to the documentation provided with the card for more information, and follow the manufacturer’s
recommendations for use. It is strongly recommended that prior to use, you must format the microSD card on the
device.
NOTE: For microSD card information see the MC93XX Mobile Computer User Guide.
CAUTION: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper ESD precau-
tions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
MC93XX Quick Start Guide
1. Power off the device.
2. Remove the battery.
3. Using a Torx T8 screwdriver with a large grip, remove the two keypad latch screws from inside the battery slot.
Figure 3 Remove Keypad Latch Screws
Keypad Latch Screws
7
MC93XX Quick Start Guide
4. Slide the keypad latches toward the bottom of the device.
Figure 4 Release Keypad Latches
Screwdriver
Keypad Latches
NOTE: If the keypad latches are hard to move, use a screwdriver to gently slide them towards the bottom of the device.
5. Turn the device over so that the keypad is visible.
6. Using a Torx T8 screwdriver with a large grip, remove the two keypad assembly screws from the top of the
keypad.
Figure 5 Remove Keypad
Keypad Screws
Keypad
microSD Card Holder
8
MC93XX Quick Start Guide
7. Lift the keypad from the device.
8. Slide the microSD card holder to the Open position.
Figure 6 Open microSD Card Holder
9. Lift the microSD card holder.
Figure 7 Lift microSD Card Holder
10.Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each
side of the door.
Figure 8 Insert microSD Card into Holder
9
MC93XX Quick Start Guide
11.Close the microSD card holder door and slide the door to the Lock position.
Figure 9 Close and Lock microSD Card in Holder
12.Align the keypad along the bottom ridge of the device, and then lay it flat.
Figure 10 Replace Keypad
10
MC93XX Quick Start Guide
13.Using a Torx T8 screwdriver with a large grip and a long shaft, secure the keypad to the device using the two
screws. Torque screws to 5.8 kgf-cm or 5.0 lbf-in.
Figure 11 Replace Keypad Screws
Keypad Screws
14.Turn the device over so that the keypad latches are visible.
15.Slide both the keypad latches toward the top of the device.
Figure 12 Slide Keypad Latches
Keypad Latches
11
Loading...