Zebra MC92N0-G User Guide

MC92N0-G
72E-162536-07
Mobile Computer
User Guide
MC92N0-G
User Guide
72E-162536-07
Rev A
ii MC92N0-G User Guide
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Zebra grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Zebra. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Zebra. The user agrees to maintain Zebra’s copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof.
Zebra reserves the right to make changes to any software or product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any Zebra Technologies Corporation, intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Zebra products.

Revision History

Changes to the original manual are listed below:
Change Date Description
-01 Rev. A 12/2012 Initial Release.
-02 Rev. A 05/31/13 Add Windows Embedded Handheld support.
-03 Rev. A 12/01/14 Zebra Rebranding
-04 Rev. A 6/2015 Add new Standard Range and Mid-Range imagers.
-05 Rev. A 8/2015 Add support for AndroidTM OS.
-06 Rev. A 11/2016 Add support for SE4850 Extended Range Imager. Remove obsolete accessories.
-07 Rev. A 1/2019 Update cleaning instructions on page 8-2.
iii
iv MC92N0-G User Guide

TABLE OF CONTENTS

Revision History ...................................................................................................................................... iii
About This Guide
Introduction ...................................................................................................................................... xiii
Documentation Set..................................................................................................................... xiii
Configurations................................................................................................................................. xiv
Software Versions............................................................................................................................ xv
Windows Mobile and Windows CE ............................................................................................ xv
Android...................................................................................................................................... xvi
Chapter Descriptions ...................................................................................................................... xvi
Notational Conventions................................................................................................................... xvi
Related Documents and Software .................................................................................................. xvii
Service Information ......................................................................................................................... xvii
Chapter 1: Getting Started
Introduction .................................................................................................................................... 1-1
Unpacking ...................................................................................................................................... 1-2
Getting Started ............................................................................................................................... 1-2
Installing the Main Battery .............................................................................................................. 1-2
Charging the Battery ...................................................................................................................... 1-3
Charging the Main Battery and Memory Backup Battery ......................................................... 1-3
Charging Spare Batteries ......................................................................................................... 1-4
Removing the Main Battery ...................................................................................................... 1-5
Starting the MC92N0-G ................................................................................................................. 1-6
Calibrating the Screen ................................................................................................................... 1-6
Windows Devices ..................................................................................................................... 1-6
Android Devices ....................................................................................................................... 1-6
Checking Battery Status ................................................................................................................ 1-6
MC92N0-G Strap ........................................................................................................................... 1-7
Battery Management ...................................................................................................................... 1-7
Battery Saving Tips .................................................................................................................. 1-7
Changing the Power Settings ................................................................................................... 1-7
Changing the Display Backlight Settings ................................................................................. 1-8
vi MC92N0-G User Guide
Changing the Display Brightness ............................................................................................. 1-8
Changing the Keypad Backlight Settings ................................................................................. 1-8
Windows Devices ............................................................................................................... 1-8
Android Devices ................................................................................................................. 1-9
Turning Off the Radios ................................................................................................................... 1-9
On Windows Embedded Handheld Devices ............................................................................ 1-9
On Windows CE Devices ......................................................................................................... 1-9
WLAN Radio ....................................................................................................................... 1-9
Bluetooth Radio with StoneStreet One Stack Enabled .................................................... 1-10
On Android Devices ............................................................................................................... 1-10
LED Indicators ............................................................................................................................. 1-11
Keypads ................................................................................................................................. 1-11
Entering Data ............................................................................................................................... 1-11
Using a Wired Headset ................................................................................................................ 1-12
Using a Bluetooth Headset .......................................................................................................... 1-13
Chapter 2: Operating the MC92N0-G with Windows OS
Introduction .................................................................................................................................... 2-1
Windows CE 7.0 ............................................................................................................................ 2-1
Start Menu ................................................................................................................................ 2-2
Control Panel ........................................................................................................................... 2-4
Windows Embedded Handheld ...................................................................................................... 2-5
Finger Scrolling ........................................................................................................................ 2-5
Home Screen ........................................................................................................................... 2-5
Classic Today Screen ........................................................................................................ 2-7
Status Bar ........................................................................................................................... 2-8
Tile Bar ............................................................................................................................. 2-10
Start Screen ..................................................................................................................... 2-10
Speaker Icon .................................................................................................................... 2-14
Locking the MC92N0-G ............................................................................................................... 2-14
Locking without PIN or Password .......................................................................................... 2-14
Locking with Simple PIN ........................................................................................................ 2-15
Locking with Strong Password ............................................................................................... 2-15
Password Locking Setup ........................................................................................................ 2-16
Using the Power Button ............................................................................................................... 2-17
Wireless LAN ............................................................................................................................... 2-17
Windows CE Devices ............................................
Windows Embedded Handheld Devices ................................................................................ 2-18
Connecting to the Internet ...................................................................................................... 2-19
Supported Applications ................................................................................................................ 2-19
Fusion Setup ................................................................................................................................ 2-20
Interactive Sensor Technology .................................................................................................... 2-23
Power Management ............................................................................................................... 2-23
Display Orientation ................................................................................................................. 2-23
Free Fall Detection ................................................................................................................. 2-23
Using a Wired Headset ................................................................................................................ 2-23
Using a Bluetooth Headset .......................................................................................................... 2-24
Resetting the MC92N0-G ............................................................................................................. 2-24
Windows CE Devices ............................................................................................................. 2-24
................................................................. 2-17
Table of Contents vii
Performing a Warm Boot .................................................................................................. 2-24
Performing a Cold Boot .................................................................................................... 2-24
Windows Embedded Handheld Devices ................................................................................ 2-25
Performing a Warm Boot .................................................................................................. 2-25
Performing a Cold Boot .................................................................................................... 2-25
Battery Health .............................................................................................................................. 2-26
Waking the MC92N0-G ................................................................................................................ 2-26
Chapter 3: Operating the MC92N0-G with Android OS
Introduction .................................................................................................................................... 3-1
Home Screen ........................................................................................................................... 3-1
Status Bar ................................................................................................................................ 3-2
Status Icons ............................................................................................................................. 3-2
Notification Icons ...................................................................................................................... 3-3
Managing Notifications ............................................................................................................. 3-4
Quick Settings .......................................................................................................................... 3-5
Application Shortcuts and Widgets .......................................................................................... 3-6
Adding an Application or Widget to the Home Screen ....................................................... 3-6
Moving Items on the Home Screen .................................................................................... 3-6
Removing an App or Widget from the Home Screen ......................................................... 3-7
Folders ..................................................................................................................................... 3-7
Creating a Folder ................................................................................................................ 3-7
Naming Folders .................................................................................................................. 3-7
Removing a Folder ............................................................................................................. 3-7
Home Screen Wallpaper .......................................................................................................... 3-8
Changing the Home Screen Wallpaper .................................................................................... 3-8
Using the Touchscreen ............................................................................................................ 3-8
Using the On-screen Keyboard ................................................................................................ 3-8
Editing Text .............................................................................................................................. 3-9
Entering Numbers, Symbols and Special Characters .............................................................. 3-9
Applications .............................................................................................................................. 3-9
Accessing Applications ..................................................................................................... 3-11
Switching Between Recent Applications .......................................................................... 3-12
Un-Locking the Screen ........................................................................................................... 3-12
Single User Mode ............................................................................................................. 3-12
MultiUser Mode ...................................................................................................................... 3-14
MultiUser Login ...................................................................................................................... 3-14
MultiUser Logout .............................................................................................................. 3-14
Resetting the Android Device ..................................
Performing a Soft Reset ......................................................................................................... 3-15
Performing a Hard Reset ....................................................................................................... 3-15
Suspend Mode ....................................................................................................................... 3-15
Applications .................................................................................................................................. 3-16
File Browser ........................................................................................................................... 3-16
People .................................................................................................................................... 3-17
Adding People .................................................................................................................. 3-17
Editing People .................................................................................................................. 3-17
Deleting People ................................................................................................................ 3-18
Gallery .................................................................................................................................... 3-18
.................................................................... 3-15
viii MC92N0-G User Guide
Working with Albums ........................................................................................................ 3-19
Share an Album ................................................................................................................ 3-19
Get Album Information ..................................................................................................... 3-19
Deleting an Album ............................................................................................................ 3-19
Working with Photos ......................................................................................................... 3-20
Viewing and Browsing Photos .......................................................................................... 3-20
Setting a Photo as a Contact Icon .................................................................................... 3-21
Share a Photo .................................................................................................................. 3-21
Deleting a Photo ............................................................................................................... 3-21
Working with Videos ............................................................................................................... 3-22
Watching Videos .............................................................................................................. 3-22
Sharing a Video ................................................................................................................ 3-23
Deleting a Video ............................................................................................................... 3-23
DataWedge Demonstration .................................................................................................... 3-23
Sound Recorder ..................................................................................................................... 3-24
PTT Express Voice Client ...................................................................................................... 3-25
PTT Audible Indicators ..................................................................................................... 3-25
Notification Icons .............................................................................................................. 3-26
Selecting a Talk Group ..................................................................................................... 3-27
PTT Communication ......................................................................................................... 3-27
Creating a Group Call ....................................................................................................... 3-27
Creating a Private Call (One to One) ............................................................................... 3-27
Disabling PTT Express Voice Client Communication ....................................................... 3-28
MLog Manager ....................................................................................................................... 3-28
RxLogger ................................................................................................................................ 3-28
Elemez ................................................................................................................................... 3-29
Disabling Elemez Data Collection .................................................................................... 3-29
Enabling Elemez Data Collection ..................................................................................... 3-30
Terminal Emulation ................................................................................................................ 3-30
Velocity ................................................................................................................................... 3-31
Wireless Local Area Networks ..................................................................................................... 3-31
Scan and Connect to a Wi-Fi Network ................................................................................... 3-32
Configuring a Wi-Fi Network .................................................................................................. 3-32
Manually Adding a Wi-Fi Network .......................................................................................... 3-34
Configuring for a Proxy Server ............................................................................................... 3-35
Configuring the Device to Use a Static IP Address ................................................................ 3-36
Advanced Wi-Fi Settings .......................................
Remove a Wi-Fi Network ....................................................................................................... 3-38
................................................................. 3-36
Chapter 4: Data Capture
Scan LED Indicators ...................................................................................................................... 4-1
Laser Scanning .............................................................................................................................. 4-1
Scanning Considerations ......................................................................................................... 4-2
Imaging .......................................................................................................................................... 4-3
Operational Modes ................................................................................................................... 4-3
Imager Scanning ...................................................................................................................... 4-3
Image Capture ......................................................................................................................... 4-6
DataWedge .................................................................................................................................... 4-7
Enable DataWedge .................................................................................................................. 4-7
Table of Contents ix
Disable DataWedge ................................................................................................................. 4-7
ScanSample ................................................................................................................................... 4-8
Using the RS507 Hands-free Imager ............................................................................................. 4-8
Pairing the RS507 Hands-Free Imager using Android HID ............................................................ 4-8
Pairing the RS507 Hands-Fee Imager Using Android SSI ............................................................. 4-9
Chapter 5: Using Bluetooth on Windows Devices
Introduction .................................................................................................................................... 5-1
Adaptive Frequency Hopping ......................................................................................................... 5-1
Security .......................................................................................................................................... 5-2
Security Mode 3 (Link Level Encryption) .................................................................................. 5-2
Microsoft Bluetooth Stack ................................................................................................... 5-2
StoneStreet One Bluetooth Stack ...................................................................................... 5-2
Bluetooth Configuration ................................................................................................................. 5-3
Bluetooth Power States ................................................................................................................. 5-4
Suspend ................................................................................................................................... 5-4
Resume .............................................................................................................................. 5-4
BTUI Window ................................................................................................................................. 5-5
Device Information ................................................................................................................... 5-5
FIPS Configuration ................................................................................................................... 5-5
Device Status ........................................................................................................................... 5-6
Using Microsoft Bluetooth Stack with Windows Embedded Handheld .......................................... 5-7
Turning the Bluetooth Radio Mode On and Off ........................................................................ 5-7
Enabling Bluetooth ............................................................................................................. 5-7
Disabling Bluetooth ............................................................................................................ 5-7
Discovering Bluetooth Device(s) .............................................................................................. 5-7
Available Services .................................................................................................................... 5-8
Object Push Services via Beam ......................................................................................... 5-8
Serial Port Services ............................................................................................................ 5-9
ActiveSync Using Serial Port Services ............................................................................. 5-10
Using Microsoft Bluetooth Stack with Windows CE ..................................................................... 5-12
Power Modes ......................................................................................................................... 5-12
Discovering Bluetooth Device(s) ............................................................................................ 5-12
Available Services .................................................................................................................. 5-13
Using Bluetooth StoneStreet One Bluetooth Stack ...................................................................... 5-14
Turning the Bluetooth Radio Mode On and Off ...................................................................... 5-14
Disabling Bluetooth (Windows CE) .................................................................................. 5-14
Enabling Bluetooth (Windows CE) ................................................................................... 5-14
Disabling Bluetooth (Windows Embedded Handheld) ...................................................... 5-14
Enabling Bluetooth (Windows Embedded Handheld) ...................................................... 5-14
Modes .........................................................
Wizard Mode .................................................................................................................... 5-15
Explorer Mode .................................................................................................................. 5-15
Discovering Bluetooth Device(s) ............................................................................................ 5-15
Available Services .................................................................................................................. 5-18
File Transfer Services ...................................................................................................... 5-18
Connecting to the Internet Using an Access Point ........................................................... 5-20
Dial-Up Networking Services ............................................................................................ 5-20
Add a Dial-up Entry .......................................................................................................... 5-22
........................................................................... 5-15
x MC92N0-G User Guide
Object Exchange Push Services ...................................................................................... 5-23
Headset Services ............................................................................................................. 5-26
Serial Port Services .......................................................................................................... 5-27
ActiveSync Using Serial Port Services ............................................................................. 5-27
Personal Area Network Services ...................................................................................... 5-28
A2DP/AVRCP Services .................................................................................................... 5-28
Connect to a HID Device .................................................................................................. 5-29
Pairing with Discovered Device(s) ......................................................................................... 5-29
Bluetooth Settings .................................................................................................................. 5-31
Device Info Tab ................................................................................................................ 5-31
Services Tab .................................................................................................................... 5-31
Security Tab ..................................................................................................................... 5-34
Discovery Tab .................................................................................................................. 5-35
Virtual COM Port Tab ....................................................................................................... 5-35
HID Tab ............................................................................................................................ 5-35
Profiles Tab ...................................................................................................................... 5-36
System Parameters Tab ................................................................................................... 5-36
Miscellaneous Tab ........................................................................................................... 5-36
Chapter 6: Using Bluetooth on Android Devices
Introduction .................................................................................................................................... 6-1
Adaptive Frequency Hopping ......................................................................................................... 6-1
Security .......................................................................................................................................... 6-2
Bluetooth Profiles ........................................................................................................................... 6-2
Bluetooth Power States ................................................................................................................. 6-2
Bluetooth Radio Power .................................................................................................................. 6-3
Enabling Bluetooth ................................................................................................................... 6-3
Disabling Bluetooth .................................................................................................................. 6-3
Discovering Bluetooth Device(s) .................................................................................................... 6-3
Changing the Bluetooth Name ....................................................................................................... 6-4
Connecting to a Bluetooth Device .................................................................................................. 6-5
Selecting Profiles on the Bluetooth Device .................................................................................... 6-5
Unpairing a Bluetooth Device ........................................................................................................ 6-5
Chapter 7: Accessories
Introduction .................................................................................................................................... 7-1
Secure Device (SD) Card .............................................................................................................. 7-5
Single Slot Serial/USB Cradle ........................................................................................................ 7-6
Four Slot Ethernet Cradle ....................................................................................................
Four Slot Charge Only Cradle ........................................................................................................ 7-9
Four Slot Spare Battery Charger ................................................................................................. 7-10
Cable Adapter Module ................................................................................................................. 7-11
Attaching and Removing ........................................................................................................ 7-11
Setup ...................................................................................................................................... 7-12
Battery Charging Indicators .................................................................................................... 7-13
Serial/USB Connection .......................................................................................................... 7-13
Universal Battery Charger (UBC) Adapter ................................................................................... 7-14
Inserting and Removing a Battery .......................................................................................... 7-14
.......... 7-8
Table of Contents xi
Battery Charging Indicators .................................................................................................... 7-14
Forklift Cradle ............................................................................................................................... 7-16
MC92N0-G Insertion and Removal ........................................................................................ 7-17
Using the Locking Mechanism ......................................................................................... 7-18
Connecting External Devices ................................................................................................. 7-18
Supported Scanners .................................................................................................................... 7-19
Chapter 8: Maintenance & Troubleshooting
Introduction .................................................................................................................................... 8-1
Maintaining the MC92N0-G ........................................................................................................... 8-1
Battery Safety Guidelines .............................................................................................................. 8-1
Cleaning ......................................................................................................................................... 8-2
Approved Cleanser Active Ingredients ..................................................................................... 8-2
Harmful Ingredients .................................................................................................................. 8-3
Cleaning Instructions ................................................................................................................ 8-3
Special Cleaning Notes ............................................................................................................ 8-3
Materials Required ................................................................................................................... 8-3
Cleaning the MC92N0-G .......................................................................................................... 8-3
Housing .............................................................................................................................. 8-3
Display ................................................................................................................................ 8-4
Scanner Exit Window ......................................................................................................... 8-4
Battery Contacts ................................................................................................................. 8-4
Cleaning Cradle Connectors .................................................................................................... 8-4
Cleaning Frequency ................................................................................................................. 8-5
Troubleshooting ............................................................................................................................. 8-6
MC92N0-G ............................................................................................................................... 8-6
Four Slot Spare Battery Charger .............................................................................................. 8-9
Single Slot Serial/USB Cradle .................................................................................................. 8-9
Cable Adapter Module ........................................................................................................... 8-10
Magnetic Stripe Reader ......................................................................................................... 8-11
Appendix A: Specifications
Technical Specifications ............................................................................................................... A-1
MC92N0-G .............................................................................................................................. A-1
Appendix B: Keypads
Introduction ................................................................................................................................... B-1
28-Key Keypad ........................................................................................................................ B-2
43-Key Keypad ........................................................................................................................ B-6
53-Key Keypad ................................................................................................................
3270 Emulator Keypad .......................................................................................................... B-14
5250 Emulator Keypad .......................................................................................................... B-18
VT Emulator Keypad ............................................................................................................. B-22
Keypad Special Functions ..................................................................................................... B-26
Special Characters ................................................................................................................ B-27
...... B-10
xii MC92N0-G User Guide

ABOUT THIS GUIDE

Introduction

This guide provides information about using the MC92N0-G mobile computer and accessories.
NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.

Documentation Set

The documentation set for the MC92N0-G is divided into guides that provide information for specific user needs.
MC92N0-G Quick Start Guide - describes how to get the MC92N0-G mobile computer up and running.
MC92N0-G User Guide - describes how to use the MC92N0-G mobile computer.
MC92N0-G Integrator Guide - describes how to set up the MC92N0-G mobile computer and the
accessories.
MC92N0-G Regulatory Guide - provides all regulatory, service and EULA information for the MC92N0-G
mobile computer.
Enterprise Mobility Developer Kit (EMDK) Help File - provides API information for writing applications.
xiv MC92N0-G User Guide

Configurations

This guide covers the following configurations:
Feature
CPU
TI OMAP 4430 1GHz X X X
Radios
WLAN: 802.11 a/b/g/n X X X
Memory
1 GB RAM / 2 GB Flash X X
512 MB RAM / 2 GB Flash X
Operating System
Android 4.4 X
Microsoft Windows Embedded Handheld 6.5.3 X
Microsoft Windows Embedded Compact 7 X X
Display
3.7” VGA color
MC9200 Premium
with Android
XX
MC9200 Premium
with Windows
MC9200 Standard
Windows
3.7” QVGA color
Data Capture
SE4750-SR Standard Range Imager
SE4750-MR Mid-Range Imager
SE-965 Standard Range Laser
SE4500-DL Driver License Imager
SE4500-SR Standard Range Imager
SE4500-HD High Density Imager (DPM)
SE1524-ER Extended Range Laser
SE4600-LR Long Range Imager
SE4850-ER Extended Range Imager
Keypads
53, 53 VT, 5250, 3270, 28, 43 X X X
53 key High Visibility X X
Audio
2 Watt Speaker X X X
Miscellaneous
IST, RFID tag X X
Condensation Resistant Option X X
XX
XX
XXX
X
XXX
X
XXX
XX
XXX
X
About This Guide xv
Feature
Software
Wavelink Terminal Emulation Green Screen (Default U/I)
Wavelink All-Touch Terminal Emulation Pre-loaded /

Software Versions

Windows Mobile and Windows CE

This guide covers various software configurations and references are made to operating system or software versions for:
AKU version
OEM version
BTExplorer version
Fusion version.
MC9200 Premium
with Android
Pre-loaded / pre-licensed
demo mode
MC9200 Premium
with Windows
CE: Pre-loaded /
pre-licensed
WM: Pre-licensed
MC9200 Standard
Windows
CE: Pre-loaded /
pre-licensed
WM: Pre-licensed
AKU Version for Windows Embedded Handheld Devices
To determine the Adaptation Kit Update (AKU) version on a Windows Embedded Handheld device, tap Start > Settings > System > About > Version.
The second line lists the operating system version and the build number. The last part of the build number represents the AKU number. For example, Build 23103.5.3.3 indicates that the device is running AKU version
5.3.3.
OEM Version
To determine the OEM software version:
On Windows Embedded Handheld devices, tap Start > Settings > System > System Information > System.
On Windows CE devices, tap Start > Settings > Control Panel > System Information > System.
BTExplorer Software
NOTE By default, the Microsoft Bluetooth stack is enabled. BTExplorer application is only available when the
StoneStreet One Bluetooth stack is enabled. Refer to the MC92N0-G Integrator Guide for information on selecting the Bluetooth stack.
To determine the BTExplorer software version:
On Windows Embedded Handheld devices, tap Start > BTExplorer > Menu > About.
On Windows CE devices, tap BTExplorer icon > Show BTExplorer > File > About.
Fusion Software
To determine the Fusion software version:
xvi MC92N0-G User Guide
On Windows Embedded Handheld devices, tap Start > Wireless Companion > Wireless Status > Versions.
On Windows CE devices, tap Wireless Strength icon > Wireless Status > Versions or tap Start > Programs >
Fusion > Wireless Status > Versions.

Android

To determine the current software versions touch > About device.
Serial number - Displays the serial number.
Model number - Displays the model number.
Android version - Displays the operating system version.
Kernel version - Displays the kernel version number.
Build number - Displays the software build number.

Chapter Descriptions

Topics covered in this guide are as follows:
Chapter 1, Getting Started, provides information on getting the mobile computer up and running for the first
time.
Chapter 2, Operating the MC92N0-G with Windows OS, explains how to use the mobile computer with
Windows CE and Windows Mobile operating system. This includes instructions for powering on and resetting the mobile computer, entering and capturing data.
Chapter 3, Operating the MC92N0-G with Android OS, explains how to use the mobile computer with
Android operating system. This includes instructions for powering on and resetting the mobile computer, entering and capturing data.
Chapter 4, Data Capture, explains how to capture data using the various scanning options.
Chapter 5, Using Bluetooth on Windows Devices, explains how to perform Bluetooth functionality on the
mobile computer with Windows CE and Windows Mobile operating system.
Chapter 6, Using Bluetooth on Android Devices, explains how to perform Bluetooth functionality on the
mobile computer with Android operating system.
Chapter 7, Accessories, describes the accessories available for the mobile computer and how to use the
accessories with the mobile computer.
Chapter 8, Maintenance & Troubleshooting, includes instructions on cleaning and storing the mobile
computer, and provides troubleshooting solutions for potential problems during mobile computer operation.
Appendix A, Specifications, includes a table listing the technical specifications for the mobile computer.
Appendix B, Keypads, contains the keypad functions/special characters for the keypads.

Notational Conventions

The following conventions are used in this document:
“Mobile computer” refers to the Zebra MC92N0-G hand-held computer.
About This Guide xvii
Italics are used to highlight the following:
Chapters and sections in this guide
Related documents
Bold text is used to highlight the following:
Dialog box, window and screen names
Drop-down list and list box names
Check box and radio button names
Icons on a screen
Key names on a keypad
Button names on a screen.
Bullets (•) indicate:
Action items
Lists of alternatives
Lists of required steps that are not necessarily sequential.
Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.

Related Documents and Software

The following documents provide more information about the MC92N0-G mobile computers.
MC92N0-G Regulatory Guide, p/n 72-161752-xx
MC92N0-G Integrator Guide, p/n 72E-162537-xx
Enterprise Mobility Developer Kits (EMDKs), available at: http://www.zebra.com/support.
Device Configuration Package (DCP for MC92N0c70) and Platform SDK (PSDK92N0c70) for MC92N0-G with Windows CE 7.0, available at: http://www.zebra.com/support.
ActiveSync software, available at: http://www.microsoft.com.
For the latest version of this guide and all guides, go to: http://www.zebra.com/support.

Service Information

If you have a problem with your equipment, contact Zebra Solutions Global Customer Support for your region. Contact information is available at: http://www.zebra.com/support.
When contacting support, please have the following information available:
Serial number of the unit
Model number or product name
Software type and version number.
Zebra responds to calls by email, telephone or fax within the time limits set forth in support agreements.
xviii MC92N0-G User Guide
If your problem cannot be solved by Zebra Support, you may need to return your equipment for servicing and will be given specific directions. Zebra is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your Zebra business product from a Zebra business partner, contact that business partner for support.

CHAPTER 1 GETTING STARTED

Introduction

This chapter explains how to install and charge the batteries, replace the strap and start the MC92N0-G for the first time.
.
Scan Button
Keypad
Indicator LED Bar Touch Screen
Microphone
Headphone Jack
Handstrap
Figure 1-1 MC92N0-G
Power Button
Trigger
1 - 2 MC92N0-G User Guide

Unpacking

Carefully remove all protective material from around the MC92N0-G and save the shipping container for later storage and shipping.
Verify that you received all equipment listed below:
mobile computer
lithium-ion battery
strap, attached to the MC92N0-G
stylus, in the stylus silo
Regulatory Guide.
Inspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment, contact the Zebra Support Center immediately. See page xvii for contact information.

Getting Started

In order to start using the MC92N0-G for the first time:
install the main battery
charge the main battery and backup battery
start the MC92N0-G
configure the MC92N0-G.
The main battery can be charged before or after it is installed. Use one of the spare battery chargers to charge the main battery (out of the MC92N0-G), or one of the cradles to charge the main battery installed in the MC92N0-G.

Installing the Main Battery

Before using the MC92N0-G, install a lithium-ion battery by sliding the battery into the MC92N0-G as shown in
Figure 1-2.
NOTE Ensure the battery is fully inserted. Two audible clicks can be heard as the battery is fully inserted. A partially
inserted battery may result in unintentional data loss.
When a battery is fully inserted in a MC92N0-G for the first time, upon first power up, the device boots and powers on automatically.
Chapter Title 1 - 3
Figure 1-2 Installing the Main Battery

Charging the Battery

CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 8-1.

Charging the Main Battery and Memory Backup Battery

Before using the MC92N0-G for the first time, charge the main battery until the amber charge indicator light remains lit (see Table 1-1 on page 1-4 for charge status indications). The main battery fully charges in less than four hours. The MC92N0-G can be charged using a cradle, the CAM, or the MSR with the appropriate power supply.
The MC92N0-G is also equipped with a memory backup battery which automatically charges from the main battery whether or not the MC92N0-G is operating or is in suspend mode. The memory backup battery retains data in memory for at least 30 minutes when the MC92N0-G's main battery is removed or fully discharged. When the MC92N0-G is used for the first time or after the memory backup battery has fully discharged, the memory backup battery requires approximately 15 hours to fully charge. Do not remove the main battery from the MC92N0-G for 15 hours to ensure that the memory backup battery fully charges. If the main battery is removed from the MC92N0-G or the main battery is fully discharged, the memory backup battery completely discharges in several hours.
When the main battery reaches a very low battery state, the combination of main battery and backup battery retains data in memory for at least 72 hours.
NOTE Do not remove the main battery within the first 15 hours of use. If the main battery is removed before the
backup battery is fully charged, data may be lost.
Use the following to charge batteries:
1 - 4 MC92N0-G User Guide
Cradles: The MC92N0-G slips into the cradles for charging the battery in the MC92N0-G (and spare
batteries, where applicable). For detailed cradle setup and charging procedures refer to the MC92N0-G Integrator Guide.
Single Slot Serial/USB Cradle.
Four Slot Ethernet Cradle
Four Slot Charge Only Cradle.
Accessories: The MC92N0-G snap-on accessories provide charging capability, when used with one of the
accessory charging cables. For detailed snap-on setup and charging procedures refer to the MC92N0-G Integrator Guide.
CAM
MSR.
Chargers: The MC92N0-G spare battery charging accessories are used to charge batteries that are removed
from the MC92N0-G. For detailed spare battery charging accessories setup and charging procedures refer to the MC92N0-G Integrator Guide.
Single Slot Serial/USB Cradle
Four Slot Spare Battery Charger
Universal Battery Charger (UBC) Adapter.
NOTE To achieve the best battery life in MC92N0-Gs with multiple radios, turn off the radios that are not being used.
See Turning Off the Radios on page 1-9 for more information.
To charge the main battery:
1. Ensure the accessory used to charge the main battery is connected to the appropriate power source.
2. Insert the MC92N0-G into a cradle or attach the appropriate snap-on module.
3. The MC92N0-G starts to charge automatically. The amber charge LED, in the Indicator LED Bar, lights to
indicate the charge status. See Table 1-1 for charging indications.
The main battery usually fully charges in less than four hours.
Table 1-1 MC92N0-G LED Charge Indicators
LED Indication
Off MC92N0-G not in cradle or connected to a CAM or MSR. MC92N0-G not placed
correctly. Charger is not powered.
Fast Blinking Amber Error in charging; check placement of the MC92N0-G.
Slow Blinking Amber MC92N0-G is charging.
Solid Amber Charging complete.
Note: When the battery is initially inserted in the MC92N0-G, the amber LED flashes once if the battery power is low or the battery is not fully inserted.

Charging Spare Batteries

Use the following three accessories to charge spare batteries:
Single Slot Serial/USB Cradle
Chapter Title 1 - 5
Four Slot Spare Battery Charger
UBC Adapter.
Refer to Chapter 7, Accessories for information on charging a spare battery using an accessory.

Removing the Main Battery

To remove the main battery:
1. Prior to removing the battery, press the red Power button.
2. Tap Safe Battery Swap.
3. The Indicator LED Bar lights red.
4. When the Indicator LED turns off, press the primary battery releases. The battery partially ejects from the
MC92N0-G.
5. Press the secondary battery release, on top of the battery, and slide the battery out of the MC92N0-G.
Primary Battery Releases
1
2
3
Secondary Battery Release
Figure 1-3 Removing the Main Battery
1
1 - 6 MC92N0-G User Guide

Starting the MC92N0-G

Press the red Power button to turn on the MC92N0-G. If the MC92N0-G does not power on, perform a cold boot. See Resetting the MC92N0-G on page 2-24 for Windows devices and Resetting the Android Device on page 3-15 for Android devices.
NOTE When a battery is fully inserted in a MC92N0-G for the first time, upon the MC92N0-G’s first power up, the
device boots and powers on automatically.
When the MC92N0-G is powered on for the first time, it initializes its system. The splash screen appears for a short period of time.

Calibrating the Screen

Windows Devices

To calibrate the screen so the cursor on the touch screen aligns with the tip of the stylus:
1. Using the stylus carefully press and briefly hold the tip of stylus on the center of each target that appears on the
screen.
NOTE To re-calibrate the screen at anytime, press FUNC + ESC on the MC92N0-G to launch the calibration
screen application.
2. Repeat as the target moves around the screen or press ESC to cancel.

Android Devices

To calibrate the screen so the cursor on the touch screen aligns with the tip of the stylus:
Touch > Display > Touch calibration.
1. Using the stylus carefully press and briefly hold the tip of stylus on the center of each target that appears on the
screen.
2. Repeat as the target moves around the screen.

Checking Battery Status

To check the charge level of the main battery or backup battery:
On Windows CE devices, tap Start > Settings > Control Panel > Power to display the Battery Status
window.
On Windows Embedded Handheld devices, tap Start > Settings > System > Power to display the Power
window.
On Android devices, touch > About device > Status.
To save battery power, set the MC92N0-G to turn off after a specified number of minutes.

MC92N0-G Strap

The strap may be moved to either the left or right side of the MC92N0-G to suit user preferences.
To reposition the strap:
1. Slip the button through the end loop and remove from the handle.
2. Open strap loop and slide the handstrap through the loop.
3. Slide the loop out of the connector post.
4. Reverse the procedure to re-attach the strap. Two strap connectors are provided on the MC92N0-G’s main
body. The handstrap may be attached to either connector.
Strap Loop
Chapter Title 1 - 7
Handstrap
Figure 1-4 Reposition the Strap

Battery Management

Battery Saving Tips

Set the MC92N0-G to turn off after a short period of non-use.
Set the display to turn off or dim backlight.
Set the keyboard backlight to turn off after a short period of non-use.
Turn off all wireless radio activity when not in use.
Power off the MC92N0-G when charging to charge at a faster rate.

Changing the Power Settings

Button
NOTE Windows Mobile and Windows CE only.
To set the MC92N0-G to turn off after a short period of non-use:
1 - 8 MC92N0-G User Guide
1. On Windows CE devices, tap Start > Settings > Control Panel > Power > Advanced.
or
On Windows Embedded Handheld devices, tap Start > Settings > System > Power > Advanced.
2. Select the On battery power: Turn off device if not used for: check box and select a value from the
drop-down list box.
3. Tap OK.

Changing the Display Backlight Settings

NOTE Windows Mobile and Windows CE only.
To change the display backlight settings in order to conserve more battery power:
1. On Windows CE devices, tap Start > Settings > Control Panel > Backlight > Battery Power.
or
On Windows Embedded Handheld devices, tap Start > Settings > System > Backlight > Battery Power.
2. Select the On battery power: Disable backlight if not used for: check box and select a value from the
drop-down list box.
3. Tap the Brightness tab.
4. Tap the Disable backlight check box to completely turn off the display backlight.
5. Use the slider to set the brightness of the backlight. Set it to a low value to save battery power.
6. Tap OK.

Changing the Display Brightness

NOTE Android Devices only.
To change the display brightness in order to conserve more battery power:
1. Touch > Display > Brightness.
Figure 1-5 Brightness Dialog Box
2. In the Brightness dialog box, use the slider to set a brightness level.
3. Touch .

Changing the Keypad Backlight Settings

Windows Devices
To change the keypad backlight settings in order to conserve more battery power:
Chapter Title 1 - 9
1. On Windows CE devices, tap Start > Settings > Control Panel > Keylight > Battery Power.
or
On Windows Embedded Handheld devices, tap Start > Settings > System > Keylight > Battery Power.
2. Select the On Battery Power: Disable keylight if not used for: check box and select a value from the
drop-down list box.
3. Tap Advanced.
4. Tap the Disable keylight check box to completely turn off the display backlight.
5. Tap OK.
Android Devices
To change the keypad backlight settings in order to conserve more battery power:
1. Touch > Display > Key light.
2. Select one of the options.
• Always on - The touch key light is on when the screen is on.
• 6 seconds - The touch key light stays on for six seconds then turns off (default).
• 10 seconds - The touch key light stays on for 10 seconds then turns off.
• 15 seconds - The touch key light stays on for 15 seconds then turns off.
• 30 seconds - The touch key light stays on for 30 seconds then turns off.
• 1 minute - The touch key light stays on for one minute then turns off.
3. Touch .

Turning Off the Radios

On Windows Embedded Handheld Devices

Windows Embedded Handheld devices include Wireless Manager, which provides a simple method of enabling, disabling, and configuring all the device’s wireless capabilities in one place.
To open Wireless Manager, tap the Status Bar and then the Connectivity icon and select Wireless Manager or tap Start > Settings > Connections > Wireless Manager.
To enable or disable a wireless connection, tap its blue bar.
To enable or disable all wireless connections, tap and hold the All bar.
To configure settings for a connection, tap Menu.

On Windows CE Devices

WLAN Radio
To turn off the WLAN radio tap the Fusion Signal Strength icon on the task tray and select Disable Radio. A red X appears across the icon indicating that the radio is disabled (off).
1 - 10 MC92N0-G User Guide
Fusion Signal Strength Icon
Figure 1-6 Fusion Signal Strength Icon
To turn the radio back on, tap the Fusion Signal Strength icon on the task tray and select Enable Radio. The red X disappears from the icon indicating that the radio is enabled (on).
Bluetooth Radio with StoneStreet One Stack Enabled
To turn off the Bluetooth radio, tap the Bluetooth icon in the task tray and select Disable Bluetooth.
Bluetooth Icon
Figure 1-7 Bluetooth Icon
To turn on the Bluetooth radio, tap the Bluetooth icon in the task tray and select Enable Bluetooth.

On Android Devices

To turn off all the radio:
1. Drag the Status bar down from the top of the screen. The Quick Settings icon displays in the top right corner.
2. Touch to display the Quick Settings panel.
3. Touch Airplane Mode.
Drag the bottom of the Quick Settings Panel to the top of the screen to close the Quick Settings screen.

LED Indicators

The MC92N0-G has an LED Indicator Bar that contains LEDs that indicate scanning and charging status. Table
1-2 describes the LED indications.
Figure 1-8 MC92N0-G LEDs Indicator Bar
Chapter Title 1 - 11
LED Indicator Bar
Table 1-2 MC92N0-G LED Indications
LED State Indication
Solid Red Laser enabled, scanning/imaging in process.
Solid Green Successful decode/capture.
Slow Blinking Amber Main battery in MC92N0-G is charging.
Fast Blinking Amber Error in charging; check placement of the MC92N0-G.
Solid Amber Main battery in MC92N0-G is fully charged.

Keypads

The MC92N0-G has the following interchangeable modular keypads:
28-key keypad
43-key keypad
53-key keypad
3270 Emulator
5250 Emulator
VT Emulator.
Refer Appendix B, Keypads to for detailed information on each keypad.

Entering Data

When entering data on the keypad, use either the single-hand method or the two-hand method as shown in Figure
1-9.
1 - 12 MC92N0-G User Guide
Single-hand Method
Figure 1-9 Entering Data on the Keypad

Using a Wired Headset

You can use a mono headset for audio communication when an audio enabled application is used. To use a headset, plug the headset jack into the audio connector on the side of the MC92N0-G. Ensure that the MC92N0-G’s volume is set appropriately before putting the headset on. When a headset is plugged into the jack, the speakerphone is muted.
Zebra recommends a 2.5mm jack headset. See Table 7-1 on page 7-1 for available Zebra headsets.
Two-hand Method
Figure 1-10 Using a Headset (MC92N0-G Shown)
Chapter Title 1 - 13

Using a Bluetooth Headset

Use a Bluetooth headset for audio communication when an audio enabled application is used. See Chapter 5,
Using Bluetooth on Windows Devices for information on connecting a Bluetooth device to the MC92N0-G. Ensure
that the MC92N0-G’s volume is set appropriately before putting the headset on. When a Bluetooth headset is connected the speakerphone is muted.
1 - 14 MC92N0-G User Guide
CHAPTER 2 OPERATING THE MC92N0-G
WITH WINDOWS OS

Introduction

This chapter explains the physical buttons, status icons and controls on the MC92N0-G, how to use the MC92N0-G, including instructions for powering on and resetting, using the stylus and a headset, entering information and data capture.

Windows CE 7.0

The Taskbar at the bottom of the window displays the active programs, current time, battery status and communication status.
Desktop Button
Start Button
Figure 2-1
Status icons are shown in the taskbar to indicate present status of the MC92N0-G. Double tapping some status icons displays the corresponding setup window and enables you to change or adjust its settings from the window. Single tapping other status icons displays corresponding menus.
Table 2-1
Status
Icon
Taskbar
Status Icons
Clock: Indicates the current time.
Battery: This icon indicates that the main battery is charging or that the terminal is operating on AC
power. Double tapping on this icon opens the Power Properties window.
Open Programs
Status Icons
Description
2 - 2 MC92N0-G User Guide
Table 2-1
Status
Icon
Status Icons (Continued)
Description
AC Plug: Indicates that the battery is fully charged and the MC92N0-G is running on external power.
Battery: This icon indicates that the battery is fully charged (100% charged).
The battery status icons provide the battery status in 10% increments from 10% to 100%.
Serial Connection: It is displayed when the terminal is connected to a host computer with a serial cable.
Wireless Connection Status: Indicates WLAN signal strength.
Bluetooth Enabled: Indicates that the Bluetooth radio is on (BTExplorer only).
Bluetooth Disabled: Indicates that the Bluetooth radio is off (BTExplorer only).
Bluetooth Communication: Indicates that the MC92N0-G is communicating with another Bluetooth
device (BTExplorer only).
DataWedge Running: Indicates that the DataWedge application is running.
DataWedge Idle: Indicates that the DataWedge application is idle.
Shift: Indicates that the SHIFT button function is selected.
FUNC: Indicates that the FUNC button function is selected.
CTRL: Indicates that the CTRL button function is selected.
ALT
ALT: Indicates that the ALT character selection is selected.
ALPHA: Indicates that the MC92N0-G is in ALPHA button mode is selected.

Start Menu

To open the Start menu, tap at the bottom left corner of the screen. Table 2-2 lists the default applications available in the Programs menu.
Getting Started 2 - 3
Table 2-2
Icon Description Icon Description
Applications in the Programs Menu
BattSwap: Use to properly shutdown the MC92N0 during battery replacement.
Video Player: Play back video files. Music Player: Play back audio files.
BTScanner CtlPanel: Set com port to
use with a Bluetooth scanner.
CtlPanel: View and change MC92N0-G settings such as: Scanner Parameters, Display Settings, Audio Settings, Printer Settings, Date and Time Settings, Touch Screen Settings, etc.
MotoBTUI: Pairs up bar code with the MC92N0-G via Bluetooth and uses the RS507 Hands-free Imager to capture the bar code data.
Fusion Folder: Open the Wireless Companion folder.
Command Prompt: Opens a DOS command prompt window.
Internet Explorer: Browse Web and WAP sites as well as download new programs and files from the Internet.
Microsoft WordPad: Create documents.
MSP Agent: Interacts with MSP agents to collect monitoring and asset information to enable the configuration, provisioning, monitoring and troubleshooting of the MC92N0-G. Refer to the MC92N0-G Integrator Guide for more information.
Remote Desktop Connection: Log onto Windows NT server type computers and use all of the programs that are available on that computer from the MC92N0-G.
WarmBoot: Warm boots the MC92N0-G. Windows Explorer: Organize and
Rapid Deployment Client: Facilitates
software downloads from a Mobility Services Platform Console FTP server to the MC92N0-G. Integrator Guide for more information.
TelentCE: Opens the Wavelink Telnet client. TelnetCE is pre-licensed on Windows CE devices.
manage files on your device.
Refer to the MC92N0-G
2 - 4 MC92N0-G User Guide

Control Panel

Table 2-3 lists the applications in the Control Panel.
Table 2-3
Icon Description Icon Description
Programs on the Control Panel
Backlight: Adjust the backlight brightness and power settings.
Certificates: certificates installed on the MC92N0-G.
Date/Time: Change date, time and time zone information.
Volume & Sounds: Select the type of actions for which to hear sounds and customize notifications for different events.
Error Reporting: Choose whether to MC92N0-G collects software operation information to use if a serious error occurs.
Internet Options: Control how the MC92N0-G connects to the internet.
See information about
Bluetooth Device Properties: Launch the Bluetooth application.
DataWedge: application. Icon appears after installation.
Dialing: Set dialing properties for modem communication and change telephony settings.
Display: Change desktop background, appearance, backlight and brightness.
Input Panel: Switch input methods and set input options.
IST Settings: Set the appropriate settings for configuring the MC92N0-G’s Interactive Sensor Technology.
Sample scanning
Keyboard: Change keyboard repeat delay and rate.
Mouse: Adjust double-click sensitivity for both the speed and timing.
Owner: Change owner’s personal profiles.
PC Connection: Change settings for connectivity of a host computer.
Regional Settings: Change how numbers, currencies, dates and times appear.
Screen Resolution: Sets the screen resolution to either QVGA or VGA. See MC92N0-G Integrator Guide for more information.
Keylight: Adjust keypad light settings.
Network and Dial-up Connections:
Connect to other computers, networks and the Internet using a modem.
Password: Set a password for the MC92N0-G.
Power: View and control MC92N0-G power settings.
Remove Programs: Remove programs installed on the MC92N0-G.
Stylus: Calibrate the touch screen and adjust double-tap timing.
Getting Started 2 - 5
Table 2-3
Icon Description Icon Description
Programs on the Control Panel
System: View system information and change memory settings.
USBConfig: Configure the MC92N0-G USB port.

Windows Embedded Handheld

The following section describes the operation of the Windows Embedded Handheld operating system.

Finger Scrolling

Windows Embedded Handheld adds finger scrolling capabilities to the display. Finger scrolling can be used to scroll up and down web pages, documents, and lists such as the contacts list, file list, message list, calendar appointments list, and more.
When finger scrolling, swipe or flick your finger on the screen. To scroll down, swipe your finger upward on the screen. To scroll up, swipe your finger downward on the screen. To auto-scroll, flick your finger upward or downward on the screen. Touch the screen to stop scrolling.
System Info: View information on the MC92N0-G’s system components.

Home Screen

The default home screen on the MC92N0-G is the Windows Handheld Home screen. The Home screen contains a Status Bar at the top of the screen and a Tile Bar at the bottom of the screen.
The Home screen is scrollable and contains a list of application plug-ins and an Information Status bar. The Information Status bar highlights the application plug-in that is under it and provides additional information.
Status Bar
Today Screen
Tile Bar
Open the Start Menu
Figure 2-2
Windows Embedded Handheld Home Screen
Tiles
Touch and hold the screen with your finger and move the Home screen up and down. As the application names move under the Information Status bar, information relevant to that application appear in the bar.
2 - 6 MC92N0-G User Guide
Figure 2-3
Moving Today Screen
Touch and hold the Information Status bar and move it up and down over an application name. Remove your finger and the Information Status bar and application name center in the screen.
Figure 2-4
Moving Information Status Bar
Application Icon
Application Information
Figure 2-5
Information Bar Example
To customize the Home screen, tap > Settings > Today. On the horizontal scroll, use Appearance to customize the background and the Items to change the display format.
Getting Started 2 - 7
Classic Today Screen
The user can change to the classic Today screen layout that is used in Windows Mobile 6.1.
Status Bar
Today Screen
Task Tray Tile Bar
Figure 2-6
Classic Today Screen
To change to the classic view tap > Settings > Home > Items.
Figure 2-7
Home Screen Settings
Deselect the Windows Default checkbox and select any of the other checkboxes and then tap .
The task bar at the bottom of the screen can contain the task tray icons listed in Table 2-4.
Table 2-4
Task Tray Icons
Icon Description
Wireless connection status:
Indicates WLAN signal strength and opens the Wireless Applications
menu.
Bluetooth Enabled: Indicates that the Bluetooth radio is on (Displays only if the StoneStreet One Bluetooth stack is enabled).
2 - 8 MC92N0-G User Guide
Table 2-4
Task Tray Icons (Continued)
Icon Description
Bluetooth Disabled: Indicates that the Bluetooth radio is off (Displays only if the StoneStreet One Bluetooth stack is enabled).
Bluetooth Communication: Indicates that the MC92N0-G is communicating with another Bluetooth device (Displays only if the StoneStreet One Bluetooth stack is enabled).
ActiveSync:
Indicates an active serial connection between the MC92N0-G and the development
computer.
DataWedge Running: Indicates that the DataWedge application is running.
DataWedge Idle: Indicates that the DataWedge application is idle.
Shift: Indicates that the SHIFT button function is selected.
FUNC: Indicates that the FUNC button function is selected.
CTRL: Indicates that the CTRL button function is selected.
ALT
ALT: Indicates that the ALT character selection is selected.
Status Bar
The Status Bar at the top of the screen displays the status icons listed in Table 2-5.
Notifications Connectivity Audio Battery
Battery Clock
Figure 2-8
Table 2-5
Icon Description Icon Description
Notifications
Status Bar Icons
Status Bar Icons
Indicates a reminder of an upcoming calendar event.
Notification that one or more instant messages were received.
Getting Started 2 - 9
Table 2-5
Status Bar Icons (Continued)
Icon Description Icon Description
Notification that one or more e-mail/text messages were received.
There are more notification icons than can be displayed.
Connectivity
Connection is active. Connection is not active.
Synchronization is occurring. WLAN available.
WLAN in use.
Audio
All sounds are on. All sounds are off.
Battery
Battery is charging. Battery has a full charge.
Battery has a high charge. Battery has a medium charge.
Battery has a low charge. Battery has a very low charge.
Tap the Status Bar to display an Icon bar. Tap an icon to get additional notification or status information.
Icon Bar
Figure 2-9
Icon Bar
2 - 10 MC92N0-G User Guide
Table 2-6
Icon Bar Icons
Icon Description
Magnify: Enlarges the screen.
Connectivity: Displays the Connectivity dialog box.
Volume: Displays the Volume dialog box.
Power: Displays the Power window.
Clock & Alarms:
Opens the Clocks & Alarms window.
Tile Bar
The Tile Bar, located at the bottom of the screen, contains the Start tile to open the Start Menu. It also displays tiles that vary depending upon the open application.
Figure 2-10
Tile Bar Examples
Start Screen
To open the Start screen, tap at the bottom left corner of the screen.
Swipe upward to view more program and folder icons.
Move often-used program and folder icons anywhere on the Start screen for easy access. Press and hold the icon to move. Drag the icon to a new location and release.
Table 2-7 lists the default icons available on the Start screen.
Table 2-7
Icon Description Icon Description
Programs on the Start Screen
Home: Displays the Home screen. Text: Send an SMS text message.
Contacts: Keep track of friends and
colleagues.
Internet Explorer: Browse Web and WAP sites as well as download new programs and files from the Internet.
E-mail: Send an Email.
Battery Swap: Properly shuts down the
MC92N0-G during battery replacement.
Getting Started 2 - 11
Table 2-7
Icon Description Icon Description
Programs on the Start Screen (Continued)
Calendar: Keep track of appointments and create meeting requests.
Pictures & Videos: View and manage pictures, animated GIFs, and video files.
Windows Media: Play back audio and video files.
Marketplace: Purchase applications from the Marketplace.
Windows Live: Use this mobile version of Windows Live™ to find information on the web.
MSN Money: Keep track of your finances.
Settings: Open the Settings folder.
Table 2-8 lists the default icons available
on the Settings folder.
Getting Started: Launch the Getting Started application.
Alarms: and time of your locale. Alarms can also be set at specified days and times of a week.
Messenger: Use this mobile version of Windows Live Messenger.
Calculator: Perform basic arithmetic and calculations, such as addition, subtraction, multiplication, and division.
MSN Weather: Check the local weather.
Set the device clock to the date
Tasks: Keep track of your tasks. Games: Play games.
Office Mobile: Use the complete suite of
Microsoft® Office applications for your mobile device (only on Windows Mobile Premium devices with manufacture date before July 2016).
File Explorer: Organize and manage files on your device.
Search Phone: Search contacts, data, and other information on the MC92N0-G. Refer to the Microsoft Applications for Windows Mobile 6 User Guide for more information.
Help: Access on-line Help topics. Task Manager: Enables viewing of
Notes: Create handwritten or typed
notes, drawings, and voice recordings.
ActiveSync: Synchronize information between the MC92N0-G and a host computer or the Exchange Server.
Internet Sharing: Connect a notebook computer to the Internet using the MC92N0-G's data connection.
memory and CPU allocations and stops running processes. Refer to the
Microsoft Applications for Windows Mobile 6 User Guide for more
information.
2 - 12 MC92N0-G User Guide
Table 2-7
Icon Description Icon Description
Programs on the Start Screen (Continued)
Adobe Reader: View pdf files. Wireless Companion: Open the
Wireless Companion folder.
BTScanner CtlPanel: Set com port to use with a Bluetooth scanner.
BT Information: Display information about the Bluetooth radio and generate a Bluetooth address bar code.
Remote Desktop Mobile: Log onto Windows NT server type computers and use all of the programs that are available on that computer from the MC92N0-G.
BTExplorer: Manages StoneStreet One Bluetooth connections. Refer to the
MC92N0-G Series MC92N0-G Integrator Guide for more information. Appears
only if the StoneStreet One Bluetooth stack is enabled.
MSP Agent: Interacts with MSP agents to collect monitoring and asset information to enable the configuration, provisioning, monitoring and troubleshooting of the MC92N0-G. Refer to the MC92N0-G Integrator Guide for more information.
Rapid Deployment Client: Facilitates software downloads from a Mobility Services Platform Console FTP server to the MC92N0-G. Integrator Guide for more information.
Refer to the MC92N0-G
RTLogExport: Use when instructed to by Zebra support personnel to extract real-time data to a log file. Alternately, press F9 to extract the data to a log file. The log file is located in the /ExportLogs folder.
Table 2-8
Icon Description Icon Description
Setting Applications
Clock & Alarms: Set the device clock to the date and time of your locale. Alarms can also be set at specified days and times of a week.
Home: Customize the appearance of the Home screen and the information to display on it.
Personal Folder: Contains personal setting applications.
System Folder: Contains system setting applications.
Lock: Set a password for the MC92N0-G.
Sounds & Notifications: Enable sounds
for events, notifications, and more, and set the type of notification for different events.
Connections Folder: Contains connection setting applications.
Getting Started 2 - 13
Table 2-8
Icon Description Icon Description
Connections Folder
Personal Folder
Setting Applications (Continued)
Beam: Set the MC92N0-G to receive incoming beams.
Bluetooth: Open the Microsoft or StoneStreet One Bluetooth application, set the MC92N0-G to visible mode and scan for other Bluetooth devices in the area.
Wi-Fi: Setup wireless network connection and customize settings.
Wireless Manager: Enables or disables the MC92N0-G’s wireless radios and customizes Wi-Fi and Bluetooth settings.
Connections: Set up one or more types of modem connections for your device, such as phone dial-up, Bluetooth, and more, so that your device can connect to the Internet or a private local network.
Domain Enroll: Make your device an AD domain member for device management and security. Refer to the Microsoft
Applications for Windows Mobile 6 User Guide for more information.
USB to PC: Enables or disables the enhanced network connectivity.
System Folder
Buttons: Assign a program to a button. Owner Information: Enter personal
information on the MC92N0-G.
About: View basic information such as
the Windows Handheld® version and type of processor used on the MC92N0-G.
Backlight: Set display backlight brightness and time-out settings.
Encryption: Allow files on a storage card to be encrypted. Encrypted files are readable only on your device.
Error Reporting: Enable or disable the Microsoft’s error reporting function.
Keylight: Set keypad backlight time-out settings.
Certificates: See information about certificates installed on the MC92N0-G.
Customer Feedback: Submit feedback on the Windows Handheld 6 software.
DataWedge: Sample scanning application.
IST Settings: Set the appropriate setting for configuring the device’s Interactive Sensor Technology.
Memory: Check the device memory allocation status and memory card information and stop currently running programs.
Managed Programs: Displays the programs that were installed on the MC92N0-G using Mobile Device Manager.
Power: Check battery power and set the time-out for turning off the display to conserve battery power.
2 - 14 MC92N0-G User Guide
Table 2-8
Icon Description Icon Description
Setting Applications (Continued)
Remove Programs: Remove programs that you installed on the MC92N0-G.
Screen: Change the screen orientation, re-calibrate the screen, and change the screen text size.
System Info: Displays the MC92N0-G’s software and hardware information.
USBConfig: Configure the MC92N0-G USB port.
Regional Settings: Set the regional configuration to use, including the format for displaying numbers, currency, date, and time on the MC92N0-G.
Task Manager: Stop running programs and processes.
UI Settings: Sets Start menu grid view.
Speaker Icon
Adjust the system volume using the Speaker icon.
1. Tap the Status Bar and then tap the Speaker icon. The Volume dialog box appears.
2. Tap and move the slide bar to adjust the volume.
3. Select the On or Off radio button to turn the speaker on or off.
NOTE Use can also adjust the system volume using the Sounds & Notifications window or by using the keypad.

Locking the MC92N0-G

Lock the MC92N0-G by disabling key presses and screen tap or by requiring a password.
Locking the MC92N0-G turns off keyboard and touch screen functionality. This is helpful when the MC92N0-G is turned on and you want to prevent accidental key presses.
To lock the device, tap > .

Locking without PIN or Password

When the MC92N0-G is locked, the Lock screen appears.
Getting Started 2 - 15
Figure 2-11
Slide the lock button left or right to unlock the screen.
Lock Screen

Locking with Simple PIN

When the MC92N0-G is locked, the Lock screen appears.
Figure 2-12
Enter the PIN and then tap Unlock.
Simple PIN Lock Screen

Locking with Strong Password

When the MC92N0-G is locked, the Lock screen appears.
2 - 16 MC92N0-G User Guide
Figure 2-13
Strong Password Lock Screen
Enter the strong password and then tap Unlock.

Password Locking Setup

Use the Password window to set a password to disable unauthorized access to the MC92N0-G.
NOTE If the MC92N0-G is configured to connect to a network, use a strong (difficult to figure out)
password to help protect network security. Password cracking tools continue to improve and the computers used to crack passwords are more powerful than ever.
1. Tap > Settings > Lock.
Figure 2-14
2. Select Prompt if device unused for check box to enable password protection.
3. From the drop-down list, select a time value for the protection to take affect after non-use.
4. From the Password type: drop-down list, select either Simple PIN or Strong alphanumeric.
5. For a simple password, enter a four-digit password in the Password field.
Password Window
For a stronger password:
a. Enter a seven character password in the Password: field. A strong password must contain at least seven
characters and contain at least three of the following: uppercase and lowercase letters, numerals, and punctuation.
b. Re-enter the password in the Confirm: field.
6. Tap .

Using the Power Button

Press the red Power button to turn the MC92N0-G screen on and off (suspend mode). The MC92N0-G is on when the screen is on and the MC92N0-G is in suspend mode when the screen is off. For more information, see Starting the MC92N0-G on page 1-6.
The Power button is also used to reset the MC92N0-G by performing a warm or cold boot.
On Windows CE devices:
Warm Boot - Resets the MC92N0-G.
Cold Boot - Resets the MC92N0-G, removes all added applications not stored in the Application folder and
restores all factory default settings.
Getting Started 2 - 17
On Windows Embedded Handheld devices:
Warm Boot - Resets the MC92N0-G. Operating system and all applications are restarted. File storage is
preserved.
Cold Boot - Resets the MC92N0-G. Operating system and all applications are restarted. File storage is
preserved. Normally only used when a warm boot does not initiate.
NOTE Applications that are added to the Application folder are not removed when a cold boot is performed. The
For information about booting the MC92N0-G, see Windows Embedded Handheld Devices on page 2-25.

Wireless LAN

NOTE By default, the WLAN is on when the MC92N0-G boots up. To set the WLAN radio to be off when
To configure the MC92N0-G, a set of wireless applications provide the tools to configure and test the wireless radio in the MC92N0-G. Refer to the Wireless Fusion Suite User Guide for Version X2.01 for information on configuring wireless profiles. Go to http://www.zebra.com/support for the latest version of this guide. See Software Versions on page xv to determine the Fusion version on the MC92N0-G.
Application folder is in flash memory.
the MC92N0-G boots up, see the MC92N0-G Integrator Guide.

Windows CE Devices

Tap the Signal Strength icon to display the Wireless Launcher menu.
2 - 18 MC92N0-G User Guide
Signal Strength Icon
Figure 2-15
Wireless Application Menu

Windows Embedded Handheld Devices

NOTE On devices with Windows Embedded Handheld, access the Wireless Launcher from the Home
screen. Select the Fusion plug-in and then tap the Fusion Menu button.
The interface to the Signal Strength icon and Wireless Launcher has changed in the Windows Embedded Handheld default Today screen. To view the Wireless Launcher, select the Fusion plug-in on the Today screen and tap the Fusion Menu soft key.
Figure 2-16
Functionality of this dialog is similar to the Wireless Launch menu. Drag the window up and down to view all menu items. Tap the icon next to the item to open it.
Fusion Plug-in on Today Screen
Getting Started 2 - 19
Wireless Launcher Window

Connecting to the Internet

To connect to the Internet on a WLAN when using Fusion Wireless Companion, ensure that the network card settings is set to Internet:
1. Ensure Fusion is enabled and a profile is configured.
2. Tap > Settings > Connections > Wi-Fi.
3. In the My network card Connects to drop-down list, select The Internet.
4. Tap OK.

Supported Applications

The Fusion menu items and their corresponding applications are summarized in Table 2-9.
Table 2-9
Find WLANs Invokes the Find WLANs application which displays a list of the WLANs
Manage Profiles Invokes the Manage Profiles application (which includes the Profile
Manage Certs Invokes the Certificate Manager application which allows the user to
Supported Applications
Application Description
active in the area.
Editor Wizard) to manage and edit the list of WLAN profiles.
manage certificates used for authentication.
Manage PACs Invokes the PAC Manager application which helps the user manage the list
of Protected Access Credentials used with Extensible Authentication Protocol-Flexible Authentication via Secure Tunneling (EAP-FAST) authentication.
Options Invokes the Options application which allows the user to configure the
Fusion option settings.
2 - 20 MC92N0-G User Guide
Table 2-9
Wireless Status Invokes the Wireless Status application which allows the user to view the
Wireless Diagnostics Invokes the Wireless Diagnostics application which provides tools with
Log on/off Invokes the Network Login dialog which allows the user to log on to a
Fusion Help Invokes Fusion Help application which provides on-device Help.

Fusion Setup

For detailed WLAN setup using Fusion, refer to the Wireless Fusion Enterprise Mobility Suite User Guide for Version X2.01.
To setup WLAN using Fusion:
NOTE Obtain the proper WLAN configuration information from the system administrator prior to performing the
Supported Applications (Continued)
Application Description
status of the current wireless connection.
which to diagnose problems with the wireless connection.
particular profile or to log off from the currently active profile
Fusion setup procedures.
The following setup procedure example shows setup of a WLAN using Wired Equivalent Privacy (WEP) encryption.
1. Tap the > Wireless Companion > Wireless Launch > Manage Profiles. The Manage Profiles window
appears.
2. Tap and hold in the window and select Add from the pop-up menu. The Wireless LAN Profile Entry window
appears.
3. In the Profile Name text box enter a name for the profile.
4. In the ESSID text box enter the ESSID.
Figure 2-17
5. Tap Next. The Operating Mode dialog box displays.
Profile ID Dialog Box
6. In the Operating Mode drop-down list, select Infrastructure or Ad-hoc.
Getting Started 2 - 21
Figure 2-18
7. Tap Next. The Security Mode dialog box displays.
8. In the Security Mode drop-down list, select Legacy (Pre-WPA).
Figure 2-19
9. In the Authentication drop-down list, select None.
10. Tap Next. The Encryption dialog box displays.
11. In the Encryption Type drop-down list, select WEP-40 (40/24).
Operating Mode Dialog Box
Security/Authentication Dialog Box
Figure 2-20
12. Select the Pass-phrase or Hexadecimal Keys radio button to indicate whether a pass-phrase or hexadecimal
Encryption Dialog Box
keys will be entered on the next page.
13. Select the For added security - Mask characters entered check box to hide characters entered. Deselect
this to show characters entered.
14. Tap Next.
2 - 22 MC92N0-G User Guide
Figure 2-21
15. In the Edit Key drop-down list, select the key to enter.
16. In the Key field, enter 10 hexadecimal characters.
17. In the Confirm field, re-enter the key. When the keys match, a message appears indicating that the keys
WEP-40 WEP Keys Dialog Box
match.
18. Repeat for each WEP key.
19. In the Transmit Key drop-down list, select the key to transmit.
20. Tap Next. The IPv4 Address Entry dialog box displays.
Figure 2-22
21. Ensure that all three check boxes are selected.
IP Address Entry Dialog Box
22. Tap Next. The Battery Usage dialog box appears.
23. In the Battery Usage Mode dialog box select a power consumption option.
Figure 2-23
24. Tap Next. The Performance Settings dialog box appears.
25. In the Performance Settings dialog box select either Optimize for Data or Optimize for Voice.
26. Tap Save.
Battery Usage Dialog Box

Interactive Sensor Technology

NOTE The Interactive Sensor Technology feature is only available on Premium configurations.
This section describes the functionality of the Interactive Sensor Technology (IST) feature on the MC92N0-G.
The IST supports the following features.
Power Management – manage power by configuring IST to control switching on/off the backlight, control suspend mode of the MC92N0-G by monitoring motion and orientation.
Display Orientation – switch the screen orientation to either landscape or portrait depending on the MC92N0-G orientation.
Free Fall Detection – monitors free fall duration and records the time and type of the drop event.

Power Management

The MC92N0-G orientation and motion sensitive data can be used as an indicator of MC92N0-G usage and can be used to manage the battery power of the MC92N0-G. For example, IST can be configured to control the backlight on and off functionality or go into suspend according to a user gesture by placing screen facing down. It can also be used to keep the MC92N0-G active while it is in movement to prevent it from quickly going into suspend mode while in use.
Getting Started 2 - 23

Display Orientation

The screen can be rotated between portrait and landscape modes automatically, depending on the physical orientation of the MC92N0-G. For example, if the MC92N0-G is rotated 90° counterclockwise, IST rotates the display counterclockwise 90° so that the screen display appears correct.
This functionality is achieved by monitoring screen angle and rotating the display to counter any changes. IST only rotates the screen in multiples of 90°.

Free Fall Detection

IST continuously monitors gravitational force on the MC92N0-G according to its current position. When the MC92N0-G free falls, IST detects the absence of gravitational force and records the event data if it detects a free fall more than 450 ms, which may indicates nearly a one meter drop. This data can be used as an indicator of potential abuse or misuse.
IST features a log for recording the free fall events. This log records the date, time and the time period of the free fall.

Using a Wired Headset

You can use a mono headset for audio communication when an audio enabled application is used. To use a headset, plug the headset jack into the audio connector on the side of the MC92N0-G. Ensure that the MC92N0-G’s volume is set appropriately before putting the headset on. When a headset is plugged into the jack, the speakerphone is muted.
Zebra recommends a 2.5mm jack headset. See Table 7-1 on page 7-1 for available Zebra headsets.
2 - 24 MC92N0-G User Guide
Figure 2-24
Using a Headset (MC92N0-G Shown)

Using a Bluetooth Headset

Use a Bluetooth headset for audio communication when an audio enabled application is used. See Chapter 5,
Using Bluetooth on Windows Devices for information on connecting a Bluetooth device to the MC92N0-G. Ensure
that the MC92N0-G’s volume is set appropriately before putting the headset on. When a Bluetooth headset is connected the speakerphone is muted.

Resetting the MC92N0-G

Windows CE Devices

There are two reset functions, warm boot and cold boot. A warm boot restarts the MC92N0-G by closing all running programs.
A cold boot also restarts the MC92N0-G, but erases all stored records and entries in RAM. Data saved in flash memory or a memory card is not lost. In addition it returns formats, preferences and other settings to the factory default settings.
Perform a warm boot first. This restarts the MC92N0-G and saves all stored records and entries. If the MC92N0-G still does not respond, perform a cold boot.
Performing a Warm Boot
Hold down the Power button for approximately five seconds. As soon as the MC92N0-G starts to perform a warm boot release the Power button.
Performing a Cold Boot
A cold boot restarts the MC92N0-G and erases all user stored records and entries that are not saved in flash memory (Application and Platform folders) or a memory card. Never perform a cold boot unless a warm boot does
not solve the problem.
CAUTION Do not hold down any key, other than the Power button during a reset. Performing a cold boot restores
formats, preferences and other settings to the default settings.
NOTE Any data previously synchronized with a computer can be restored during the next ActiveSync operation.
Getting Started 2 - 25
To perform a cold boot:
1. Press the red Power button. The PowerKey Action window appears.
2. Tap Safe Battery Swap.
3. Press the primary battery release on the MC92N0-G to partially eject the battery from the MC92N0-G.
4. While the battery is partially released, simultaneously press and release the handle trigger and the Power
button.
5. Push the battery to fully re-insert it in the MC92N0-G. One audible click can be heard as the battery is fully
inserted.
6. The MC92N0-G reboots.
7. Calibrate the screen. See Calibrating the Screen on page 1-6 to calibrate the MC92N0-G screen.

Windows Embedded Handheld Devices

There are two reset functions, warm boot and cold boot.
A warm boot restarts the MC92N0-G and closes all running programs.
A cold boot also restarts the MC92N0-G and closes all running programs but also installs some drivers.
Data saved in flash memory or a memory card is not lost. Perform a warm boot first. This restarts the MC92N0-G and saves all stored records and entries. If the MC92N0-G still does not respond, perform a cold boot.
Performing a Warm Boot
Hold down the Power button for approximately five seconds. As soon as the MC92N0-G starts to perform a warm boot release the Power button.
Performing a Cold Boot
A cold boot restarts the MC92N0-G. The operating system and all applications are restarted. File storage is preserved.Only perform a cold boot if a warm boot does not solve the problem.
To perform a cold boot:
1. Press the red Power button. The PowerKey Action window appears.
2. Tap Safe Battery Swap. The Indicator LED Bar lights red.
3. Press the primary battery release on the MC92N0-G to partially eject the battery from the MC92N0-G.
4. While the battery is partially released, simultaneously press and release the trigger and the Power button.
5. Push the battery to fully re-insert it in the MC92N0-G. One audible click can be heard as the battery is fully
inserted.
6. The MC92N0-G reboots.
2 - 26 MC92N0-G User Guide

Battery Health

The health of the battery can be viewed on the MC92N0-G Power applet.
On Windows CE devices, tap Start > Settings > Control Panel >Power icon > BatteryMgmt tab. On Windows Embedded Handheld devices, tap Start > Settings > System > Power > BatteryMgmt tab.
Table 2-10
State of Health Indicates the current state of the battery (Healthy or Unhealthy).
Battery Usage Indicator Indicates the usage of the battery.
Battery Usage Threshold Indicates the usage indicator threshold.
Battery Serial # Displays the serial number of the battery.
For information on changing the Battery Usage Threshold, refer to the MC92N0-G Mobile Computer Integrator
Guide.
BatteryMgmt Window
Item Description

Waking the MC92N0-G

The wakeup conditions define what actions wake up the MC92N0-G after it has gone into suspend mode. The MC92N0-G can go into suspend mode by either pressing the Power button or automatically by Control Panel time-out settings. These settings are configurable and the factory default settings are shown in Table 2-11. To set the wake up conditions on Windows Embedded Handheld devices, tap Start > Settings > Power > Wakeup tab or on Windows CE devices, Start > Settings > Control Panel > Power > Wakeup tab.
Table 2-11
Wakeup Default Settings
Condition for Wakeup Power Button Automatic Time-out
MC92N0-G is connected to a serial accessory. No Yes
MC92N0-G is connected to a USB device. Yes Yes
The scan triggered is pressed. No Yes
The screen is touched. No No
Bluetooth activity. Yes Yes
On Motion No Yes
USB Host No No
Key is pressed. No Yes
Real-time Clock Alarm Yes Yes
IST Accelerometer Yes Yes
CHAPTER 3 OPERATING THE MC92N0-G
WITH ANDROID OS

Introduction

This chapter explains the physical buttons, status icons and controls on the MC92N0-G, how to use the MC92N0-G, including instructions for powering on and resetting, using the stylus and a headset, entering information and data capture.

Home Screen

The Home screen displays when the MC9200 turns on. Depending upon the configuration, the Home screen might appear different. Contact your system administrator for more information.
After a suspend or screen time-out, the Home screen displays with the lock sliders. Slide to the right toward
to unlock the screen. For screen locking information see Un-Locking the Screen on page 3-12.
1
6
5
4
Figure 3-1 Home Screen
2
3
3 - 2 MC92N0-G User Guide
Table 3-1 Home Screen Items
Item Description
1 — Status Bar Displays the time, status icons (right side), and notification icons (left side). For
2 — Browser Icons Opens Browser application.
3 — All Apps Icon Opens the APPS window.
4 — Shortcut Icons Opens applications installed on the MC9200. See Application Shortcuts and
5 — Widgets Launches stand-alone applications that run on the Home screen. See
The Home screen provides four additional screens for placement of widgets and shortcuts. Swipe the screen left or right to view the additional screens.
more information see Status Icons on page 3-2 and Managing Notifications on
page 3-4.
Widgets on page 3-6 for more information.
Application Shortcuts and Widgets on page 3-6 for more information.

Status Bar

The Status bar displays the time, notification icons (left side) and status icons (right side).
Status IconsNotification Icons
Figure 3-2 Notification and Status Icons
If there are more notifications than can fit in the Status bar, displays indicating that more notifications exist. Open the Notifications panel to view all notifications and status.

Status Icons

Table 3-2 Status Icons
Icon Description
Indicates that the Alarm is active.
Indicates that all sounds except media and alarms are silenced and vibrate mode is active.
Indicates that the MC92N0-G is in silent mode.
Indicates that the battery is fully charged.
Table 3-2 Status Icons (Continued)
Icon Description
Indicates that the battery is partially drained.
Indicates that the battery charge is low.
Indicates that the battery charge is very low.
Indicates that the battery is charging.
Indicates that the Airplane Mode is active. All radios are turned off.
Indicates that Bluetooth is on.
Indicates that the MC9200 is connected to a Bluetooth device.
Chapter Title 3 - 3
Connected to a Wi-Fi network.
No Wi-Fi signal.
Indicates that the Alpha key is pressed.
Indicates that the Blue key is pressed.
Indicates that the ALT key is pressed.
Indicates that the CTRL key is pressed.
Indicates that the Shift key is pressed.
Indicates that the Shift key is locked.

Notification Icons

Table 3-3 Notification Icons
Icon Description
Indicates that more notifications are available for viewing.
Indicates that data is syncing.
3 - 4 MC92N0-G User Guide
Table 3-3 Notification Icons (Continued)
Icon Description
Indicates an upcoming event.
Indicates that an open Wi-Fi network is available.
Indicates that a song is playing.
Indicates that a problem with sign-in or sync has occurred.
Indicates that the MC9200 is uploading data.
Indicates that the MC9200 is downloading data when animated and download is complete when static.
Indicates that the MC9200 is connected via USB cable.
Indicates that the MC9200 is connected to or disconnected from virtual private network (VPN).
Preparing SD card.
Indicates that USB debugging is enabled on the MC9200.
Indicates that the MultiUser feature is enabled. Appears only when MultiUser Administrator application is installed.
Indicates that a new user is logging in. Appears only when MultiUser Administrator application is installed.
Indicates the status of the PTT Express Voice Client. See Notification Icons on page 3-3 for complete list of PTT Express notification icons.

Managing Notifications

Notification icons report the arrival of new messages, calendar events, and alarms, as well as ongoing events. When a notification occurs, an icon appears in the Status bar with a brief description. See Notification Icons on page 3-3 for a list of possible notification icons and their description. Open the Notifications panel to view a list of all the notifications.
To open the Notification panel drag the Status bar down from the top of the screen.
Figure 3-3 Notification Panel
Chapter Title 3 - 5
To respond to a notification, open the Notifications Panel and then touch a notification. The Notifications Panel closes and the subsequent activity is dependent on the notification.
To clear all notifications, open the Notifications Panel and then touch . All event-based notifications are removed. Ongoing notifications remain in the list.
Touch to open the Quick Settings screen.
To close the Notification Panel, drag the bottom of the Notifications Panel to the top of the screen or touch .

Quick Settings

The Quick Settings panel provides easy access to some frequently used settings.
Drag the Status bar down from the top of the screen. The Quick Settings icon displays in the top right corner. Touch
to display the Quick Settings panel.
3 - 6 MC92N0-G User Guide
Figure 3-4 Quick Settings
• Owner – Display the owner’s contact image. Touch to open the owner’s contact information.
• Brightness – Opens the Brightness setting dialog box to set the screen brightness.
• Settings – Opens the Settings screen.
• Wi-Fi – Displays the current Wi-Fi connection. Touch to opens the Wi-Fi settings screen.
• Battery – Displays the current battery charge level. Touch to opens the Battery screen.
• Airplane Mode – Displays the Airplane mode status. Touch to toggle Airplane mode on and off. Turn on
Airplane mode to turn off all the radios.
• Bluetooth – Displays the current state of the Bluetooth radio. Touch to open the Bluetooth settings screen.
• Location – Displays the current state of the Location settings. Touch to opens the Location settings screen.
To close the Quick Settings Panel, drag the bottom of the Quick Settings Panel to the top of the screen, touch at the top right corner of the screen or touch .

Application Shortcuts and Widgets

Application shortcuts placed on the Home screen allow quick and easy access to applications. Widgets are self-contained applications placed on the Home screen to access frequently used features.
Adding an Application or Widget to the Home Screen
1. Go to the desired Home screen.
2. Touch .
3. Swipe right, if necessary, to find the application icon or widget.
4. Touch and hold the icon or widget until the Home screen appears.
5. Position the icon on the screen and then release.
Moving Items on the Home Screen
1. Touch and hold the item until it floats on the screen.
Chapter Title 3 - 7
2. Drag the item to a new location. Pause at the edge of the screen to drag the item onto an adjacent Home
screen.
3. Lift finger to place the item on the Home screen.
Removing an App or Widget from the Home Screen
1. Go to the desired Home screen.
2. Touch and hold the application shortcut or widget icon until it floats on the screen.
3. Drag the icon to on the top of the screen and then release.

Folders

Use Folders to organize similar applications together. Tap the folder to open and display items in the folder.
Creating a Folder
To create a folder, there must be at least two app icons on the Home screen.
1. Go to the desired Home screen.
2. Touch and hold on one application icon.
3. Drag the icon and stack on top of another icon.
4. Lift and release.
Naming Folders
1. Touch the folder.
Figure 3-5 Open Folder
2. Touch the title area and enter a folder name using the keyboard.
3. Touch Done.
4. Touch anywhere on the Home screen to close the folder. The folder name appears under the folder.
Figure 3-6 Renamed Folder
Removing a Folder
1. Touch and hold the folder icon until it enlarges and the device vibrates.
2. Drag the icon to and release.
3 - 8 MC92N0-G User Guide

Home Screen Wallpaper

NOTE Use of Live Wallpaper may reduce battery life.

Changing the Home Screen Wallpaper

NOTE Use of Live Wallpaper may reduce battery life.
1. On the Home screen, touch and hold until the menu appears.
2. From the Choose wallpaper from menu, touch Gallery, Live wallpapers or Wallpapers.
• Gallery - Select to use an image stored on the device.
• Live wallpapers - Select to use an animated wallpaper image.
• Wallpapers - Select to use a wallpaper image.
3. Touch Save or Set wallpaper.

Using the Touchscreen

Use the multi-tap sensitive screen to operate the device.
•Tap - Tap to:
select items on the screen
type letters and symbols using the on-screen keyboard
press on-screen buttons.
• Tap and Hold - Tap and hold:
an item on the Home screen to move it to a new location or to the trash.
an item in Apps to create a shortcut on the Home screen.
the Home screen to open a menu for customizing the Home screen.
an empty area on the Home screen until the menu appears.
• Drag - Tap and hold an item for a moment and then move finger on the screen until reaching the new
position.
• Swipe- Move finger up and down or left and right on the screen to:
unlock the screen
view additional Home screens
view additional application icons in the Launcher window
view more information on an application’s screen.
• Double-tap - Tap twice on a web page, map, or other screen to zoom in and out.

Using the On-screen Keyboard

Use the on-screen keyboard to enter text in a text field. To configure the keyboard settings, touch (comma) > and then select Android keyboard settings.
Chapter Title 3 - 9

Editing Text

Edit entered text and use menu commands to cut, copy, and paste text within or across applications. Some applications do not support editing some or all of the text they display; others may offer their own way to select text.

Entering Numbers, Symbols and Special Characters

To enter numbers and symbols:
Touch and hold one of the top-row keys until a menu appears then select a number. Keys with alternate
characters display an ellipsis ( ... ) below the character.
Touch and hold the Shift key with one finger, touch one or more capital letters or symbols to enter them, and
then lift both fingers to return to the lowercase keyboard.
Touch to switch to the numbers and symbols keyboard.
Touch the key on the numbers and symbols keyboard to view additional symbols.
To enter special characters, touch and hold a number or symbol key to open a menu of additional symbols.
A larger version of the key displays briefly over the keyboard.
Keys with alternate characters display an ellipsis ( ... ) below the character.

Applications

The APPS screen displays icons for all installed applications. The table below lists the applications installed on the device. Refer to the MC9200-G Integrator Guide for information on installing and uninstalling application.
Table 3-4 Applications
Icon Description
App Gallery - Provides links to utilities and demonstration applications that can be installed
on the MC9200.
Battery Manager - Displays battery information, including charge level, status, health and wear level.
Bluetooth Pairing Utility – Use to pair the RS507 Hans-free Imager with the MC9200 by scanning a bar code.
Browser - Use to access the Internet or intranet.
Calculator - Provides the basic and scientific arithmetic functions.
Calendar - Use to manage events and appointments.
Clock - Use to schedule alarms for appointments or as a wake-up.
3 - 10 MC92N0-G User Guide
Table 3-4 Applications (Continued)
Icon Description
DataWedge - Enables data capture using the imager.
Downloads - lists all downloads files.
DWDemo - Provides a way to demonstrate the data capture features using the imager. See
DataWedge Demonstration on page 3-23 for more information.
elemez — Use to provide diagnostic information. See Elemez on page 3-29 for more information.
Email - Use to send and receive email.
File Browser - Organize and manage files on the MC9200. See File Browser on page 3-16
for more information.
Gallery - Use to view photos stored on the SD card. For more information, see Gallery on page 3-18 for more information.
MLog Manager - Use to capture log files for diagnostics. See MLog Manager on page 3-28 for more information.
MobiControl Client - Opens the MobiControl Stage application to stage the device.
MSP Agent - Enables management of the MC9200 from an MSP server. Requires the
purchase of an appropriate MSP client license per device to suit the level of management functionality required.
Music - Play music stored on the SD card.
People - Use to manage contact information. People on page 3-17 for more information.
PTT Express - Use to launch PTT Express client for VoIP communication.
Rapid Deployment - Allows the MC9200 to stage a device for initial use by initiating the
deployment of settings, firmware and software. Requires the purchase of an MSP client license per device.
RxLogger - Use to diagnose device and application issues. See the MC9200 Integrator Guide for more information.
Search - Use the Google search engine to search the Internet and the MC9200.
Table 3-4 Applications (Continued)
Icon Description
Settings - Use to configure the MC9200.
Sound Recorder - Use to record audio.
StageNow - Allows the MC9200 to stage a device for initial use by initiating the deployment
of settings, firmware and software.
Terminal Emulation - Opens Wavelink Terminal Emulation application. This application is pre-licensed.
Velocity - Opens the Wavelink all-touch terminal emulation application. The application is set to demo mode. Contact Wavelink for purchasing licenses.
AppLock Administrator - Use to configure the Application Lock feature. This icon appears after the optional application is installed.
Chapter Title 3 - 11
MultiUser Administrator - Use to configure the MultiUser feature. This icon appears after the optional application is installed.
Secure Storage Administrator - Use to configure the Secure Storage feature. This icon appears after the optional application is installed.
Accessing Applications
All applications installed on the device are accessed using the APPS window.
1. On the Home screen, touch .
Figure 3-7 APPS Window
2. Slide the APPS window left or right to view more application icons. Touch an icon to open the application.
NOTE See Application Shortcuts and Widgets on page 3-6 for information on creating a shortcut on the Home
screen.
3 - 12 MC92N0-G User Guide
Switching Between Recent Applications
1. Touch and hold . A window appears on the screen with icons of recently used applications.
Figure 3-8 Recently Used Applications
2. Slide the window up and down to view all recently used applications.
3. Swipe left or right to remove application from the list and force close the application.
4. Touch an icon to open it or touch to return to the current screen.

Un-Locking the Screen

Use the Lock screen to protect access to data on the MC9200. Some email account require locking the screen. Refer to the MC9200 Integrator Guide for information on setting up the locking feature. The Locking feature functions differently in Single User mode or Multiple User mode.
Single User Mode
When locked, a pattern, PIN or password is required to unlock the device. Press the Power button to lock the screen. The device also locks after a pre-defined time-out.
Press and release the Power button to wake the device.
The Lock screen displays. Slide to the right toward to unlock the screen.
If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen.
If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
Figure 3-9 Lock Screen
Chapter Title 3 - 13
Figure 3-10 PIN Screen
Figure 3-11 Pattern Screen
3 - 14 MC92N0-G User Guide
Figure 3-12 Password Screen

MultiUser Mode

With MultiUser login, multiple users can log on to the device with each user having access to various applications and features. When enabled, the Login screen appears after powering on, resetting or after the device wakes from suspend mode.

MultiUser Login

1. In the Login text field, enter the username.
Figure 3-13 Multiple User Log In Screen
2. In the Password text field, enter the password.
3. Touch OK. After a resume from suspend, the user must enter the password.
MultiUser Logout
1. Drag the Status Bar down from the top of the screen.
2. Touch MultiUser is active.
3. Touch Logout.
4. The Login screen appears.

Resetting the Android Device

There are two reset functions, soft reset and hard reset.

Performing a Soft Reset

Perform a soft reset if applications stop responding.
1. Press and hold the Power button until the menu appears.
2. Touch Reset.
3. The device shuts down and then reboots.

Performing a Hard Reset

CAUTION Performing a hard reset with a SD card installed in the MC9200 may cause damage or data corruption
to the SD card.
Chapter Title 3 - 15
To perform a hard reset(if the device is completely non-responsive, skip steps 1 and 2).
1. Press the red Power button.
2. Tap Safe Battery Swap. The Indicator LED Bar lights red.
3. Press the primary battery release on the MC92N0-G to partially eject the battery from the MC92N0-G.
4. While the battery is partially released, simultaneously press and release the trigger and the Power button.
5. Push the battery to fully re-insert it in the MC92N0-G. One audible click can be heard as the battery is fully
inserted.
6. The MC92N0-G reboots.
7. When the screen turns off, release the buttons.
8. The MC9200 reboots.

Suspend Mode

The MC9200 goes into suspend mode when the user presses the Power button or after a period of inactivity (set in the Display settings window).
To wake the MC9200 from Suspend mode, press the Power button.Alternately, press the trigger to wake the device.
The Lock screen displays. Slide to the right toward to unlock the screen. If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen. See Un-Locking the Screen on page 3-12.
NOTE If the user enters the PIN, password or pattern incorrectly five times, they must wait 30 seconds before
trying again.
If the user forgets the PIN, password or pattern contact the system administrator.
3 - 16 MC92N0-G User Guide
Figure 3-14 Lock Screen

Applications

This section describes the applications installed on the device.

File Browser

Use the File Browser application to view and mange files on the device.
To open File Browser, touch > .
3 4
1 2
Figure 3-15 File Browser Screen
The address bar (1) indicates the current folder path. Touch the current folder path to manually enter a path and folder name.
5
Use (2) to select multiple files/folder.
Use (3) to view the internal storage root folder.
Use (4) to view the SD card root folder.
Use (5) to view the previous folder or to exit the application.
Chapter Title 3 - 17
Touch and hold an item to perform an operation on that item. Select one of the options from the File Operations menu:-
• Information - View detailed information about the file or folder.
• Move - Move the file or folder to a new location.
• Copy - Copy the select file.
• Delete - Delete the selected file.
• Rename - Rename the select file.
• Open as - Open the selected file as a specific file type.
• Share - Share the file with other devices.
Touch to open additional functionality:
Touch > New Folder to create a new folder in the current folder.
Touch > Search to search for a file or folder.
Touch > Sort to sort the list by name, by type, by size or by date.
Touch > Refresh to re-display the contents of the current folder.
Touch > List View to change the folder view from tile to list format.
Touch > Change Size to change the size of the icons: Large, Normal or Small.
Touch > About File Browser to view the application version information.

People

Use the People application to manage contacts.
From a Home or Apps screen, touch . People opens to the main list of contacts. View contacts in three ways at the top of the screen: Groups , All contacts , and Favorites. Touch the tabs to change how to view the contacts. Swipe up or down to scroll through the lists.
Adding People
1. In the People application, touch .
2. If there are more than one account with contacts, touch the one to use.
3. Type the contact’s name and other information. Touch a field to start typing, and swipe down to view all
categories.
4. To add more than one entry for a category – for example, to add a work address after typing a personal
address – touch Add new for that field. To open a menu with preset labels, such as Home or Work for an email address, touch the label to the right of the item of contact information. Or, to create your own label, touch
Custom in the menu.
5. Touch Done.
Editing People
1. In the People application, touch tab.
2. Touch a person to edit.
3. Touch .
3 - 18 MC92N0-G User Guide
4. Touch Edit.
5. Edit the contact information.
6. Touch Done.
Deleting People
1. In the People application, touch tab.
2. Touch a person to edit.
3. Touch .
4. Touch Delete.
5. Touch OK to confirm.

Gallery

NOTE The device supports the following image formats: jpeg, gif, png and bmp.
The device supports the following video formats: H.263, H.264 and MPEG4 Simple Profile.
Use Gallery to:
view photos
play videos
perform basic editing of photos
set photos as wallpaper
set photos as a contact photo
share photos and videos.
To open the Gallery application, touch > or in the camera application touch the thumbnail image at the top right.
Gallery presents all photos and videos stored on the SD card and internal memory.
Figure 3-16 Gallery — Albums
Chapter Title 3 - 19
Touch an album to open it and view its contents. The photos and videos in the album are displayed in
chronological order.
Touch a photo or video in an album to view it.
Touch icon (top left corner) to return to the main Gallery screen.
Touch to return to the main Gallery screen.
Working with Albums
Albums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in a chronologically ordered grid. The name of the album displays at the top of the screen.
Figure 3-17 Photos Inside an Album
Swipe left or right to scroll images across the screen.
Share an Album
1. Touch .
2. Touch .
3. Touch and hold an album until it highlights.
4. Touch other albums as required.
5. Touch . The Share menu opens. Touch the application to use to share the selected albums.
6. Follow the instructions within the selected application.
Get Album Information
1. Touch .
2. Touch .
3. Touch and hold an album until it highlights.
4. Touch .
5. Touch Details.
Deleting an Album
To delete an album and its contents from the SD card:
3 - 20 MC92N0-G User Guide
1. Touch .
2. Touch .
3. Touch and hold an album until it highlights.
4. Check other albums to delete. Ensure that other albums are selected.
5. Touch .
6. In the Delete selected item? menu, touch OK to delete the album.
Working with Photos
Use Gallery to view photos on the SD card and edit and share photos.
Viewing and Browsing Photos
To view a photo:
1. Touch .
2. Touch .
3. Touch an album to open it.
4. Touch a photo.
Figure 3-18 Photo Example
5. Swipe left or right to view the next or previous photo in the album.
6. Turn the device to view the photo in upright (portrait) or sideways (landscape) orientation. The photo is
displayed (but not saved) in the new orientation.
7. Touch the photo to view the controls.
8. Double-tap the screen to zoom in or pinch two fingers together or spread them apart to zoom in or out.
9. Drag the photo to view parts that are not in view.
Cropping a Photo
1. In Gallery, touch a photo to view the controls.
2. Touch .
3. Touch Crop. The blue/white cropping tool appears.
4. Use the cropping tool to select the portion of the photo to crop.
Drag from the inside of the cropping tool to move it.
Drag an edge of the cropping tool to resize it to any proportion.
Drag a corner of the cropping tool to resize it with fixed proportions.
Figure 3-19 Cropping Tool
5. Touch Save to save a copy of the cropped photo. The original version is retained.
Chapter Title 3 - 21
Setting a Photo as a Contact Icon
1. Touch .
2. Touch .
3. Touch an album to open it.
4. Touch the photo to open it.
5. Touch .
6. Touch Set picture as.
7. Touch Contact photo.
8. In the People application, touch a contact.
9. Touch the blue box and crop the photo accordingly.
10. Touch OK.
Share a Photo
1. Touch .
2. Touch .
3. Touch an album to open it.
4. Touch a photo to open it.
5. Touch .
6. Touch the application to use to share the selected photo. The application selected opens with the photo
attached to a new message.
Deleting a Photo
1. Touch .
3 - 22 MC92N0-G User Guide
2. Touch .
3. Touch an album to open it.
4. Touch a photo to open it.
5. Touch .
6. Touch .
7. Touch Delete.
8. Touch OK to delete the photo.

Working with Videos

Use Gallery to view videos on the SD card and share videos.
Watching Videos
1. Touch .
2. Touch .
3. Touch an album to open it.
4. Touch a video.
Figure 3-20 Video Example
5. Touch . The video begins to play.
Figure 3-21 Video Example
6. Touch the screen to view the playback controls.
Sharing a Video
1. Touch .
Chapter Title 3 - 23
2. Touch .
3. Touch an album to open it.
4. Touch a video to open it.
5. Touch . The Share menu appears.
6. Touch the application to use to share the selected video. The application selected opens with the video
attached to a new message.
Deleting a Video
1. Touch .
2. Touch .
3. Touch an album to open it.
4. Touch a video to open it.
5. Touch .
6. Touch .
7. Touch Delete.
8. Touch OK.

DataWedge Demonstration

Use DataWedge Demonstration to demonstrate data capture functionality.
3 - 24 MC92N0-G User Guide
Figure 3-22 DataWedge Demonstration Window
Table 3-5 DataWedge Demonstration Icons
Icon Description
Not applicable.
/
/
See the MC9200 Integrator Guide for information on DataWedge configuration.
Either press the trigger or touch the yellow scan button to enable data capture. The captured data appears in the text field below the yellow button.
Toggles the data capture function between the internal scanner, imager or RS507 Hands-free Bluetooth imager (if connected).
Toggles between normal scan mode and picklist mode when using the imager to capture bar code data.
Opens a menu to view the application information or to set the application DataWedge profile.

Sound Recorder

Use Sound Recorder to record audio messages.
Recordings are saved on the SD card (if installed) or the Internal Storage and available in the Music application playlist titled "My Recordings."
Figure 3-23 Sound Recorder Application

PTT Express Voice Client

NOTE PTT Express Voice Client creates Push-To-Talk (PTT) communication capability between disparate
enterprise devices. Leveraging existing Wireless Local Area Network (WLAN) infrastructure, PTT Express delivers simple PTT communication without the need of a voice communication server.
Chapter Title 3 - 25
• Group Call: Press and hold the green Group Call button to start communicating with other voice client users.
• Private Response: Press and hold the red Private Call button to respond to the originator of the last
broadcast or to make a Private Response.
PTT Audible Indicators
The following tones provide helpful cues when using the voice client.
• Talk Tone: Double chirp. Plays when the Group (or Private) button is depressed. This is a prompt for the user
to start talking.
• Access Tone: Single beep. Plays when another user just finished a broadcast or response. The user is now
able to initiate a Group Call or Private Call.
• Busy Tone: Continuous tone. Plays when the Group (or Private) button is depressed and another user is
already communicating on the same talkgroup. Plays after the maximum allowed talk time is reached (60 seconds).
• Network Tone:
Three increasing pitch beeps. Plays when PTT Express has acquired the WLAN connection and the
service is enabled.
Three decreasing pitch beeps. Plays when PTT Express has lost the WLAN connection or the service is
disabled.
3 - 26 MC92N0-G User Guide
Notification Icon
Service Indication
Figure 3-24 PTT Express Default User Interface
Table 3-6 PTT Express Default user Interface Descriptions
Item Description
Settings
Enable/Disable Switch
Notification
Indicates the current state of the PTT Express client.
Icon
Service Indication
Indicates the status of the PTT Express client. Options: Service Enabled, Service Disabled or Service Unavailable.
Talk Groups Lists all 32 Talk Groups available for PTT communication.
Settings Opens the PTT Express Settings screen.
Enable/Disabl
Turns the PTT service on and off.
e Switch
Notification Icons
Indicates the current state of the PTT Express Voice client.
Table 3-7 PTT Express Default User Interface Descriptions
Status Icon Description
Indicates that PTT Express Voice client is disabled.
Indicates that PTT Express Voice client is enabled but not connected to a WLAN.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and listening on the Talk Group indicated by the number next to the icon.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and communicating on the Talk Group indicated by the number next to the icon.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and in a private response.
Chapter Title 3 - 27
Table 3-7 PTT Express Default User Interface Descriptions
Status Icon Description
Indicates that PTT Express Voice client is enabled and muted.
Indicates that the PTT Express Voice client is enabled but it is not able to communicate due to a VoIP telephony call is in progress.
Selecting a Talk Group
One of 32 Talk Groups can be selected by PTT Express users. However, only one talk group may be enabled at a time on the device. Touch one of the 32 Talk Groups. The selected Talk Group is highlighted.
PTT Communication
NOTE This section describes the default PTT Express client configuration. See the PTT Express V1.2 User
Guide for detailed information on using the client.
PTT communication may be established as a Group Call or Private Call. When PTT Express is enabled, the buttons on the left side of the device are assigned for PTT communication. When the Wired Headset is used, Group Calls and Private Calls can also be initiated using the headset Talk button.
Group Call
Button
Private Call Button
Figure 3-25 PTT Buttons
Creating a Group Call
1. Press and hold the green Group Call button and listen for the talk tone to play.
2. If a busy tone is heard, release the green Group Call button and wait a moment before making another
attempt. Ensure that PTT Express and the WLAN are enabled.
3. Start talking after the talk tone is heard.
NOTE If the user holds the button for more than 60 seconds (default), the call is dropped allowing others to make
Group calls. The user should release the button when finished talking to allow others to make calls.
4. Release the button when finished talking.
Creating a Private Call (One to One)
The Private Call can only be initiated once a Group Call has been established.
3 - 28 MC92N0-G User Guide
The initial Private Call is made to the last talker on the Group Call.
1. Wait until an access tone is heard.
2. Within 10 seconds, press and hold the red Private Call button, and listen for the talk tone to play.
If a busy tone is heard, release the red Private Call button and wait a moment before making another attempt. Ensure that PTT Express and the WLAN are enabled.
3. Start talking after the talk tone plays.
4. Release the Private Call button when finished talking.
Disabling PTT Express Voice Client Communication
1. Touch > .
2. Slide the Enable/Disable Switch to the OFF position. The button changes to OFF.
3. Touch .

MLog Manager

Use MLog Manager to capture log files for diagnostics. See the MC9200 Integrator Guide for detailed information on configuring the application.
Figure 3-26 MLog Manager

RxLogger

RxLogger is a comprehensive diagnostic tool that provides application and system metrics. It allows for custom plug-ins to be created and work seamlessly with this tool. RxLogger is used to diagnose device and application issues. Its information tracking includes the following: CPU load, memory load, memory snapshots, battery consumption, power states, wireless logging, cellular logging, TCP dumps, Bluetooth logging, logcat, FTP push/pull, ANR dumps, etc. All logs and files generated are saved onto flash storage on the device (internal or external).
Figure 3-27 RxLogger

Elemez

NOTE Elemez collects specific device information in the background and sends this information to us to help improve
Chapter Title 3 - 29
product functionality. This feature can be disabled. See Disabling Elemez Data Collection on page 3-29.
Ensure that the date, time and time zone are set correctly prior to using Elemez.
Use Elemez to provide diagnostics information to Zebra. Touch Submit Diagnostics button to send the data.
Figure 3-28 Elemez Application
Disabling Elemez Data Collection
The user can disable the Elemez application from collection specific data in the background and sending it to Zebra Technologies.
1. Touch > Apps.
2. Swipe left or right until the ALL tab displays.
3. Scroll through the list and touch Elemez.
4. In the App info screen, touch Uninstall updates.
5. In the Uninstall updates dialog box, touch OK.
6. Touch OK.
3 - 30 MC92N0-G User Guide
7. After uninstall is complete, touch OK.
8. In the All tab, scroll through the list and touch Elemez.
9. Touch Disable.
10. In the Disable built-in app? dialog box, touch OK.
11. Touch .
Enabling Elemez Data Collection
The user can re-enable the Elemez application for collection specific data in the background and sending it to Zebra Technologies.
1. Touch > Apps.
2. Swipe left or right until the ALL tab displays.
3. Scroll through the list and touch Elemez.
4. In the App info screen, touch Enable.
5. Touch .
6. Touch > .
7. Touch Enable Elemez.

Terminal Emulation

The Wavelink Terminal Emulation application provides a solution for accessing and managing connections to applications resident on host systems using 5250, 3270, VT, and HP emulation.
Figure 3-29 Wavelink Terminal Emulation
Chapter Title 3 - 31

Velocity

The Wavelink Velocity application provides an all-touch user interface that replaces legacy green screen TE applications.
Figure 3-30 Wavelink Velocity Sample Screen

Wireless Local Area Networks

Wireless local area networks (WLANs) allow the MC9200 to communicate wirelessly inside a building. Before using the MC9200 on a WLAN, the facility must be set up with the required hardware to run the WLAN (sometimes known as infrastructure). The infrastructure and the MC9200 must both be properly configured to enable this communication.
Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches, Radius servers, etc.) for instructions on how to set up the infrastructure.
Once the infrastructure is set up to enforce the chosen WLAN security scheme, use the Wireless & networks settings configure the MC9200 to match the security scheme.
The MC9200 supports the following WLAN security options:
Open
Wireless Equivalent Privacy (WEP).
Wi-Fi Protected Access (WPA)/WPA2 Personal (PSK).
Extensible Authentication Protocol (EAP).
Protected Extensible Authentication Protocol (PEAP) - with MSCHAPV2 and GTC authentication.
Transport Layer Security (TLS)
TTLS - with Password Authentication Protocol (PAP), MSCHAP, MSCHAPv2 and GTC authentication.
The Status bar displays icons that indicate Wi-Fi network availability and Wi-Fi status. See Status Bar on page 3-2 for more information.
NOTE Turn off Wi-Fi when not using it, to extend the life of the battery.
3 - 32 MC92N0-G User Guide

Scan and Connect to a Wi-Fi Network

1. Touch .
Figure 3-31 Settings Screen
1. Slide the Wi-Fi switch to the ON position.
2. Touch Wi-Fi. The MC9200 searches for WLANs in the area and lists them.
Figure 3-32 Wi-Fi Screen
3. Scroll through the list and select the desired WLAN network.
4. For open networks, touch profile once or press and hold and then select Connect to network or for secure
networks enter the required password or other credentials then touch Connect. See the system administrator for more information.
5. The MC9200 obtains a network address and other required information from the network using the dynamic
host configuration protocol (DHCP) protocol. To configure the MC92N0-G with a fixed internet protocol (IP) address, See Configuring the Device to Use a Static IP Address on page 3-36.
6. In the Wi-Fi setting field, Connected appears indicating that the MC92N0-G is connected to the WLAN.

Configuring a Wi-Fi Network

To set up a Wi-Fi network:
1. Touch .
Chapter Title 3 - 33
2. Touch Wi-Fi.
3. Slide the switch to the ON position.
4. The device searches for WLANs in the area and lists them on the screen.
5. Scroll through the list and select the desired WLAN network.
6. Touch the desired network. If the network security is Open, the device automatically connects to the network.
For all other network security a dialog box appears.
Figure 3-33 WLAN Network Security Dialog Box
7. If the network security is WEP or WPA/WPS2 PSK, enter the required password and then touch Connect.
8. If the network security is 802.1x EAP:
Touch the EAP method drop-down list and select PEAP, TLS, TTLS, LEAP or FAST.
3 - 34 MC92N0-G User Guide
Touch the Phase 2 authentication drop-down list and select an authentication method.
If required, touch CA certificate and select a Certification Authority (CA) certificate. Note: Certificates are installed using the Security settings.
If required, touch User certificate and select a user certificate. Note: User certificates are installed using
the Location & security settings.
If required, in the Identity text box, enter the username credentials.
If desired, in the Anonymous identity text box, enter an anonymous identity username.
If required, in the Password text box, enter the password for then given identity.
NOTE By default, the network Proxy is set to None and the IP settings is set to DHCP. See Configuring for a
Proxy Server on page 3-35 for setting connection to a proxy server and see Configuring the Device to Use a Static IP Address on page 3-36 for setting the device to use a static IP address.
9. Touch Connect.
10. Touch .

Manually Adding a Wi-Fi Network

Manually add a Wi-Fi network if the network does not broadcast its name (SSID) or to add a Wi-Fi network when out of range.
1. Touch .
2. Touch Wi-Fi.
3. Slide the Wi-Fi switch to the On position.
4. Touch + in the top right corner of the screen.
5. In the Network SSID text box, enter the name of the Wi-Fi network.
6. In the Security drop-down list, select the type of security. Options:
None
WEP
WPA/WPA2 PSK
• 802.1x EAP.
7. If the network security is None, touch Save.
8. If the network security is WEP or WPA/WPA2 PSK, enter the required password and then touch Save.
9. If the network security is 802.1x EAP:
Touch the EAP method drop-down list and select PEAP, TLS, TTLS, LEAP or FAST.
Touch the Phase 2 authentication drop-down list and select an authentication method.
If required, touch CA certificate and select a Certification Authority (CA) certificate. Note: Certificates are installed using the Security settings.
If required, touch User certificate and select a user certificate. Note: User certificates are installed using the Security settings.
If required, in the Identity text box, enter the username credentials.
If desired, in the Anonymous identity text box, enter an anonymous identity username.
Chapter Title 3 - 35
If required, in the Password text box, enter the password for then given identity.
By default, the network Proxy is set to None and the IP settings is set to DHCP. See Configuring for a
Proxy Server on page 3-35 for setting connection to a proxy server and see Configuring the Device to Use a Static IP Address on page 3-36 for setting the device to use a static IP address.
1. Touch Connect.
2. Touch .

Configuring for a Proxy Server

A proxy server is a server that acts as an intermediary for requests from clients seeking resources from other servers. A client connects to the proxy server, requesting some service, such as a file, connection, web page, or other resource, available from a different server. The proxy server evaluates the request according to its filtering rules. For example, it may filter traffic by IP address or protocol. If the request is validated by the filter, the proxy provides the resource by connecting to the relevant server and requesting the service on behalf of the client.
It is important for enterprise customers to be able to set up secure computing environments within their companies, and proxy configuration is an essential part of doing that. Proxy configuration acts as a security barrier ensuring that the proxy server monitors all traffic between the Internet and the intranet. This is normally an integral part of security enforcement in corporate firewalls within intranets.
1. In the network dialog box, touch a network.
2. Touch Show advanced options checkbox.
3. Touch Proxy settings and select Manual.
Figure 3-34 Proxy Settings
4. In the Proxy hostname text box, enter the address of the proxy server.
5. In the Proxy port text box, enter the port number for the proxy server.
NOTE When entering proxy addresses the Bypass proxy for field, do not use spaces or carriage returns between
addresses.
6. In the Bypass proxy for text box, enter addresses for web sites that do not require to go through the proxy
server. Use the separator “|” between addresses.
7. Touch Connect.
8. Touch .
3 - 36 MC92N0-G User Guide

Configuring the Device to Use a Static IP Address

By default, the device is configured to use Dynamic Host Configuration Protocol (DHCP) to assign an Internet protocol (IP) address when connecting to a wireless network. To configure the device to connect to a network using a static IP address:
1. In the network dialog box, touch a network.
2. Touch Show advanced options checkbox.
3. Touch IP settings and select Static.
Figure 3-35 Static IP Settings
4. In the IP address text box, enter an IP address for the device.
5. If required, in the Gateway text box, enter a gateway address for the device.
6. If required, in the Network prefix length text box, enter a the prefix length.
7. If required, in the DNS 1 text box, enter a Domain Name System (DNS) address.
8. If required, in the DNS 2 text box, enter a DNS address.
9. Touch Connect.
10. Touch .

Advanced Wi-Fi Settings

NOTE Advanced Wi-Fi settings are for the device not for a specific wireless network.
Use the Advanced settings to configure additional Wi-Fi settings. From the Wi-Fi screen, touch > Advanced to view the advanced settings.
General
• Network notification - When enabled, notifies the user when an open network is available.
• Keep Wi-Fi on during sleep - Opens a menu to set whether and when the Wi-Fi radio turns off.
• Always On - The radio stays on when the device enters suspend mode (default).
• Only when plugged in - The radio stays on while the device is connected to external power.
• Never On - The radio turns off when the device enters suspend mode.
• Install Certificates – Touch to install certificates.
• Wi-Fi optimization – Touch to minimize battery usage when Wi-Fi is on (default – disabled)
• MAC address - Displays the Media Access Control (MAC) address of the device when connecting to
Wi-Fi networks.
Chapter Title 3 - 37
Regulatory
• Country selection - Displays the acquired country code if 802.11d is enabled else it displays the currently
selected country code.
Band and Channel Selection
• Wi-Fi frequency band - Use to select the frequency band. Options: Auto (default), 5 GHz only or 2.4 GHz only.
• Available channels (2.4 GHz) - Use to select specific channels. Touch to display the Available channels menu. Select specific channels. Touch OK.
• Available channels (5 GHz) - Use to select specific channels. Touch to display the Available channels menu. Select specific channels. Touch OK.
Logging
• Advanced Logging – Touch to enable advanced logging. Advanced logging
• Wireless logs - Use to capture Wi-Fi log files.
• Fusion Logger - Touch to open the Fusion Logger application. This application maintains a history of
high level WLAN events which helps to understand the status of connectivity.
Figure 3-36 Fusion Logger Screen
• Fusion Status - Touch to display live status of WLAN state. Also provides information of device and
connected profile.
Figure 3-37 Fusion Status Screen
About
• Version - Displays the current Fusion information.
3 - 38 MC92N0-G User Guide

Remove a Wi-Fi Network

To remove a remembered or connected network:
1. Touch .
2. Touch Wi-Fi.
3. In the Wi-Fi networks list, touch and hold the name of the network.
4. In the menu, touch Forget network.
5. Touch .

CHAPTER 4 DATA CAPTURE

The MC92N0-G has integrated laser scanners or imagers that collect data by scanning bar codes.
SE-965 Standard Range Laser
SE1524-ER Extended Range Laser
SE4500-SR Standard Range Imager
SE4500-DL - Driver License Imager (Windows only)
SE4500-HD - High Density Imager (DPM) (Windows only)
SE4750-SR Standard Range Imager (Premium only)
SE4750-MR Mid-Range Imager (Premium only)
SE4600-LR Long Range Imager (Windows only)
SE4850-ER Extended Range Imager.

Scan LED Indicators

The red/green Scan LED Indicators (located in the Indicator LED Bar) indicates the scan status. For the location of the Scan LED Indicators see, Figure 1-1 on page 1-1.
Table 4-1 Scan LED Indicators
LED Status Indication
Off Not scanning.
Solid Red Laser enabled, scanning in process.
Solid Green Successful decode.

Laser Scanning

To read a bar code, a scan-enabled application is required. The MC92N0-G contains the DataWedge and ScanSample (Windows CE devices only) applications that allows the user to enable the scanner to decode bar
code data and display the bar code content. See DataWedge on page 4-7 for information on enabling DataWedge and ScanSample on page 4-8 for launching ScanSample application.
4 - 2 MC92N0-G User Guide
1. Launch a scanning application or a sample scanning application (DataWedge or ScanSample).
2. Point the exit window on the top of the MC92N0-G at a bar code.
3. Press the trigger or scan button. Ensure the red scan beam covers the entire bar code. The Scan LED
Indicators illuminate red to indicate that the laser is on. The Scan LED Indicators illuminate green and a beep sounds to indicate a successful decode.
Figure 4-1 Laser Aiming
4. Release the trigger or scan button.

Scanning Considerations

Scanning consists of; aim, scan and decode. Scanning performance can be optimized by considering the range and the scanning angle:
Range
Any scanning device decodes well over a particular working range (minimum and maximum distances from the bar code). This range varies according to bar code density and scanning device optics.
Scanning within range brings quick and constant decodes; scanning too close or too far away prevents decodes. Move the scanner closer and further away to find the right working range for the bar codes being scanned. However, the situation is complicated by the availability of various integrated scanning modules. The best way to specify the appropriate working range per bar code density is through a chart called a decode zone for each scan module. A decode zone simply plots working range as a function of minimum element widths of bar code symbols.
Angle
The scan angle is important for optimizing decode performance. When laser beams reflect directly back into the scanner from the bar code, this specular reflection can “blind” the scanner.
To avoid this, scan the bar code so that the beam does not bounce directly back. But do not scan at too sharp an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode. Practice quickly shows what tolerances to work within.
NOTE Contact the Zebra Support if chronic scanning difficulties develop. Decoding of properly printed bar codes
should be quick and effortless.
Loading...