Zebra MC9090 CE Mobile Computer 6110 Printer Adapter English

Warranty

(A) Warranty Symbol Technologies (hereafter “Seller”) hardware Products are warranted against defects
in workmanship and materials for a period of three (3) mont hs from the date of shipment, unless otherwise
provided by Seller in writing, provided the Product remains un modified and is operated under normal and
proper conditions. Warranty provisions and durations on software, integrated installed systems, Product
modified or designed to meet specif ic customer specifications (“Custom Products”), remanufactured
products, and reconditioned or upgrade d products, shall be as provided in the applicable Product
specification in effect at the time of purchase or in the accompanying software license.
(B) Spare Parts Spare parts (i.e. parts, components, or subassemblies sold by Seller for use in the service
and maintenance of Products) are warranted ag ainst defects in workmanship and materials for a period of
thirty (30) days from the date of shipment. Spare parts ma y be new or originate from returned units under
the conditions set forth in subsection D below.
(C) Repair of Symbol-branded hardware For repairs on Symbol-branded hardware Products under this
Agreement, including repairs cover ed by warranty, the repair services provided are warrant ed against
defects in workmanship and materials on the repaired component of the Product for a period
of thirty (30) days from the shipment dat e of the repaired Product, or until the end of the original warran ty
period, whichever is longer.
(D) Product Service Products may be serviced or manufactured with parts, components, or
subassemblies that originate from returned products and that have been tested as meeting applicable
specifications for equivalent new materi al and Products. The sole obligation of Seller for defective
hardware Products is limited to repa ir or replacement (at Seller’s option) on a “return to service depot”
basis with prior Seller authorization. Customer is responsible for shipment to the Seller and assumes all
costs and risks associated with this transportation; return shipment to the Customer will be at Seller's
expense. Customer shall be responsible for ret urn shipment charges for product returned where Seller
determines there is no defect (“No Defect Found”), or for product returned that Seller determines is not
eligible for warranty repair. No charge will be made to Buyer for replacement parts for warranty repairs.
Seller is not responsible for any damage to or loss of any software programs, data or removable data
storage media, or the restoration or rein stallation of any software programs or data other than the
software, if any, installed by Seller during manufacture of the Product.
(E) Original Warranty Period Except for the warranty applying solely to the repair ed component arising
from a repair service as provided in Section C above, the aforeme ntioned provisions do not extend the
original warranty period of any Product tha t had either been repaired or repl aced by Seller.
(F) Warranty Provisions The above warranty provisions shall not apply to any Product (i) which has been
repaired, tampered with, altered o r modified, except by Seller’s authorized service personnel; (ii) in which
the defects or damage to the Produ ct result from normal wear and tear, misuse, negligence, improper
storage, water or other liquids, battery le akage, use of parts or accessories not approved or supplied by
Symbol, or failure to perform operator h andling and scheduled maintenance instructions supplied by
Seller; (iii) which has been subjected to unusual p hysical or electrical stress, abuse, or accident, or forces
or exposure beyond normal use wit hin the specified operational and environmental parameters set forth
in the applicable Product specification; nor shall the abo ve warranty provisions apply to any expendable or
consumable items, such as batteries, supplied with the Product .
EXCEPT FOR THE WARRANTY OF TITLE AND THE EXPRESS WARRANTIES STATED ABOVE, SELLER
DISCLAIMS ALL WARRANTIES ON PRODUCTS FURNISHED HEREUNDER INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY
PERIOD. SOME STATES OR COUNTRIES DO NOT ALLOW A LIMITATION ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
FOR CONSUMER PRODUCTS. IN SUCH STATES OR COUNTRIES, FOR SUCH PRODUCTS, SOME
EXCLUSIONS OR LIMITATIONS OF THIS LIMITED WARRANTY MAY NOT APPLY.
The stated express warranties are in lieu of all obligations or liabilities on the part of Seller for damages,
including but not limited to, special, indirect o r consequential damages arising out of or in connection with
the use or performance of the Product or ser vice. Seller’s liability for damages to Buyer or others resulting
from the use of any Product or service f urnished hereunder shall in no way exceed the purchase price of
said Product or the fair market value of said service, except in instances of injury to persons or p roperty.

Service Information

Before using the unit, it must be configured to operate in the facility’s network and run required
applications.
If a problem is encountered running or u sing the unit or equipment, contact the facility’s Technical or
Systems Support. If there is a problem with the equipment, they will contact the Symbol Support Center:

United States 1-800-653-5350

United Kingdom 0800 328 2424 Asia/Pacific [phone]
Australia 1-800-672-906 Austria/Österreich 1-505-5794-0
Denmark/Danmark 7020-1718 Finland/Suomi 9 5407 580
France 01-40-96-52-21 Germany/Deutchland 6074-49020
Italy/Italia 2-484441 Mexico/México 5-520-1835
Netherlands/Nederland 315-271700 Norway/Norge [phone]
South Africa 11-8095311 Spain/España 91 324 40 00

Sweden/Sverige 84452900 [phone]

Latin America
Sales Support

Europe/Mid-East
Distributor Operations

1-631-738-2400

1-800-347-0178 Inside US
[phone] Outside US

Contact local distributor or call
[phone]

Canada 905-629-7226

Inside Spain

Outside Spain

For the latest version of this guide go to: http://www.symbol.com/manuals.

6110 Printer
Adapter

Installation Procedures

Introduction

The 6110 Printer Adapter is specifically designed to fit into an
Intermec® model 4820/6820 printer configured with the 6110 Terminal
Holder. The adapter allows the Symbol MC9000-S mobile computer to
be used with the Intermec® printer. These installation instructions
provide the procedures to install the printer adapter, without making
any permanent changes to the printer. In addition, printer software
update procedures are required as well as the installation of the printer
drivers into the MC9000-S mobile computer. These required procedures
are provided at: http//:www.symbol.com/devzone.

Prior to installing the printer adapter, confirm that all of the components
have been received:

• Printer adapter

• Two (2) long pan head machine screws, #8-32 X 3”.

Step 1: Remove Screws

Use a phillips head screwdriver to remove the two screws from the
6110 Terminal Holder..

Remove Screws

Step 2: Store Screws

Screw the terminal holder screws into the back of the printer adapter
to store screws. Tightem the screws approximately ten turns, do not
over tighten or sreews may protude through the printer adapter face.

Step 3: Insert Printer Adapter

Insert the printer adapter into the existing terminal holder.

72-67221-01
Revision A — March 2004

Step 4: Lock Printer Adapter in Place

Slide the printer adapter down to lock into place.

Step 5: Install Retaining Screws

Install the two long screws (provided with the printer adapter) as shown.
Tighten screws using 14-15 in.lbs torque.

Step 6: Printer and Mobile Computer Software
Update

• The printer software must be configured to work with the mobile
computer. These required procedures are provided at:
http//:www.symbol.com/devzone.

• The mobile computer must have the new printer drivers installed.
These required procedures are provided at:
http//:www.symbol.com/devzone.

Insert and Remove the Mobile Computer

To insert the mobile computer:

1. Slide the mobile computer in, bottom first

2. Pivot the mobile computer under the locking clip.

Locking Clip

Charging Status

The amber LED in the LED Indicator Bar indicates the mobile computer
charging status.

Charging Indications:

• No light not charging

• Slow Flash normal charge

• Solid light full charge

• Fast Flash charging error
To remove the mobile computer:

1. Lift the locking clip

2. Pivot the mobile computer away from the printer adapter and lift
out.

Locking Clip

Power Limitations

The Intermec® printer power supply is designed to limit current draw to
approximately 1 A. At higher current draws the printer stops supplying
power to the mobile computer. Whenever the mobile computer is used
with the Intermec
off. This ensures that adequate charging current is available to charge the
mobile computer battery.

®

printer the WWAN and WLAN radios should be turned

Regulatory Information

All Symbol devices are designed to be compliant with rules and regulations
in locations they are sold and will be labeled as required.
Any changes or modifications to Symbol Technologies equipment, not
expressly approved by Symbol Technologies, could void the user's authority
to operate the equipment.

Health and Safety Recommendations

An air bag inflates with great force. DO NOT place objects, including either
installed or portable wireless equipment, in the area over the air bag or in
the air bag deployment area. If in-vehicle wireless equipment is improperly
installed and the air bag inflates, serious injury could result.
Position your device within easy reach. Be able to access your device
without removing your eyes from the road.
Do not take notes or use the device while driving. Jotting down a "to do"
list or flipping through your address book takes attention away from your
primary responsibility, driving safely.

Radio Frequency Interference Requirements

Tested to comply
with FCC Standards

FOR HOME OR OFFICE USE

This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
recepti on, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.

Radio Frequency Interference Requirements-

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Radio Frequency Interference Requirements­Canada

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.

Marking and European Economic Area (EEA)

Symbol Technologies, Inc., hereby declares that this device is in
compliance with all the applicable Directives, 89/336/EEC, 73/
23/EEC,95/54/EEC. A Declaration of Conformity may be
obtained from: http://www2.symbol.com/doc/