No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means,
without permission in writing from Symbol. This includes electronic or mechanical means, such as
photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to
change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is
on a licensed basis. Symbol grants to the user a non-transferable and non-exclusive license to use each
software or firmware program delivered hereunder (licensed program). Except as noted below, such license may
not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Symbol. No
right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The
user shall not modify, merge, or incorporate any form or portion of a licensed program with other program
material, create a derivative work from a licensed program, or use a licensed program in a network without
written permission from Symbol. The user agrees to maintain Symbol’s copyright notice on the licensed
programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part.
The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to
the user or any portion thereof.
Symbol reserves the right to make changes to any software or product to improve reliability, function, or design.
Symbol does not assume any product liability arising out of, or in connection with, the application or use of any
product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any Symbol Technologies,
Inc., intellectual property rights. An implied license only exists for equipment, circuits, and subsystems
contained in Symbol products.
®
Symbol
Bluetooth
ActiveSync
, Spectrum One®, and Spectrum24® are registered trademarks of Symbol Technologies, Inc.
®
wireless technology is a registered trademark of Bluetooth SIG. Microsoft®, Windows® and
®
are either registered trademarks or trademarks of Microsoft Corporation. Other product names
mentioned in this manual may be trademarks or registered trademarks of their respective companies and are
hereby acknowledged.
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, New York 11742-1300
http://www.symbol.com
Page 5
Revision History
Changes to the original manual are listed below:
ChangeDateDescription
-01 to -0212/2003Added Bluetooth functionality.
-01 to -0212/2003Updated cold boot instructions.
-01 to -0212/2003Updated Spectrum24 configuration to V. 3.9.2
-01 to -0212/2003Added 9000 Demo sample application programs clarification note to Appendix B.
-01 to -0212/2003Added ImagerSample to Appendix B.
-02 to -034/2004Added "optimizing display" information to the Power Window - Advanced Tab.
-02 to -034/2004Added WWAN chapters and related information throughout book.
-02 to -034/2004Updated Spectrum24 chapter.
-02 to -034/2004Added additional MC9000-K 53-key keypad.
-03 to -046/2004Added MC9000_K 28-key keypad.
-03 to -046/2004Updated battery removal procedure.
-03 to -046/2004Added Vehicle Cradle and Modem Module accessories.
-03 to -046/2004Added keypad brightness display control (color units).
-03 to -046/2004Updated Bluetooth operation.
-03 to -046/2004Updated battery voltage (technical specifications).
-03 to -046/2004Added registry settings for Enter/Return and Green/Red dot keys.
-03 to -046/2004Added information about applying applications to F6/F7 keys.
-04 to -057/2004Bluetooth update.
-05 to -069/2004Updated supported Symbologies.
-05 to -069/2004Updated Power key descriptions in keypad tables.
-05 to -069/2004Added valid battery charging temperature ranges.
-06 to -0711/2004Added 38-key numeric/function and 38-key alpha/shifted numeric keypads for the
MC9000-S.
Page 6
ChangeDateDescription
-06 to -0711/2004Added Rapid Deployment Client information (Chapter 8, Rapid Deployment
Client).
-06 to -0711/2004Updated Radio Power window information (Chapter 3, Settings).
-06 to -0711/2004Added Adaptive Frequency Hopping information (Chapter 6, Bluetooth Wireless
Technology).
-06 to -0711/2004Added additional Reader Params descriptions in the Scanner Settings section
(Chapter B, Demo Program).
-07 to -0807/2005Updated 38-Key Numeric/Function Keypad (MC9000-S) and 38-Key Numeric/
Function Keypad Configuration (MC9000-S) on page D-70.
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Page 27
Introduction
xxi
This Product Reference Guide provides information about MC9000-K and MC9000-S mobile
®
computers using the Microsoft
Windows® Mobile 2003 Software for Pocket PCs and its
accessories. The MC9000-K and MC9000-S mobile computers include the following variations:
®
•MC9000-K: Windows
Mobile 2003 Software for Pocket PCs operating system performs
1-dimensional bar code scanning with batch communication; memory configuration 64 MB
ROM/64 MB RAM; 28-key, 43-key and 53-key interchangeable keypads; QVGA color touch
panel display; Rapid Deployment.
•MC9060-K: Windows
®
Mobile 2003 Software for Pocket PCs operating system performs 1dimensional bar code scanning (models with an integrated laser scanner), or 1-dimensional
and 2-dimensional bar code scanning (models with an integrated imager); 802.11b
Spectrum24
®
wireless technology to perform local area network (LAN) communication;
Bluetooth wireless technology; monochrome or QVGA color touch panel display; memory
configuration 64 MB ROM/64 MB RAM; 28-key, 43-key and 53-key interchangeable
keypads; Rapid Deployment.
•MC9062-K: Windows
®
Mobile 2003 Software for Pocket PCs operating system performs 1dimensional bar code scanning (models with an integrated laser scanner), or 1-dimensional
and 2-dimensional bar code scanning (models with an integrated imager); 802.11b
Spectrum24
®
wireless technology to perform local area network (LAN) communication;
Bluetooth wireless technology; monochrome or QVGA color touch panel display; memory
configuration 64 MB ROM/64 MB RAM; 28-key, 43-key and 53-key interchangeable
keypads; GSM/GPRS wireless technology to perform wide area network (WAN) phone
communication; Rapid Deployment.
•MC9063-K: Windows
®
Mobile 2003 Software for Pocket PCs operating system performs 1dimensional bar code scanning (models with an integrated laser scanner), or 1-dimensional
and 2-dimensional bar code scanning (models with an integrated imager); 802.11b
Spectrum24
®
wireless technology to perform local area network (LAN) communication;
Bluetooth wireless technology; monochrome or QVGA color touch panel display; memory
configuration 64 MB ROM/64 MB RAM; 28-key, 43-key and 53-key interchangeable
keypads; CDMA wireless technology to perform wide area network (WAN) phone
communication; Rapid Deployment.
®
•MC9000-S: Windows
Mobile 2003 Software for Pocket PCs operating system performs
1-dimensional bar code scanning with batch communication; memory configuration 64 MB
ROM/64 MB RAM; 28-key, 38-key numeric/function and 38-key alpha/shifted numeric
interchangeable keypads; QVGA color touch panel display; Rapid Deployment.
Page 28
xxii
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
•MC9010-S: Windows® Mobile 2003 Software for Pocket PCs operating system performs 1-
®
dimensional bar code scanning with integrated laser scanner; 802.11 Spectrum24
wireless
technology to perform local area network (LAN) communication; memory configuration 64
MB ROM/64 MB RAM; 28-key, 38-key numeric/function and 38-key alpha/shifted numeric
interchangeable keypads; QVGA monochrome touch panel display; Rapid Deployment.
•MC9060-S: Windows® Mobile 2003 Software for Pocket PCs operating system performs 1dimensional bar code scanning with integrated laser scanner; 802.11b Spectrum24
®
wireless technology to perform local area network (LAN) communication; Bluetooth wireless
technology; memory configuration 64 MB ROM/64 MB RAM; 28-key, 38-key numeric/
function and 38-key alpha/shifted numeric interchangeable keypads; monochrome or QVGA
color touch panel display; Rapid Deployment.
•MC9062-S: Windows® Mobile 2003 Software for Pocket PCs operating system performs 1dimensional bar code scanning with integrated laser scanner; 802.11b Spectrum24
®
wireless technology to perform local area network (LAN) communication; Bluetooth wireless
technology; memory configuration 64 MB ROM/64 MB RAM; 28-key, 38-key numeric/
function and 38-key alpha/shifted numeric interchangeable keypads; monochrome or QVGA
color touch panel display; GSM/GPRS wireless technology to perform wide area network
(WAN) phone communication; Rapid Deployment.
•MC9063-S: Windows® Mobile 2003 Software for Pocket PCs operating system performs 1dimensional bar code scanning with integrated laser scanner; 802.11b Spectrum24
®
wireless technology to perform local area network (LAN) communication; Bluetooth wireless
technology; memory configuration 64 MB ROM/64 MB RAM; 28-key, 38-key numeric/
function and 38-key alpha/shifted numeric interchangeable keypads; monochrome or QVGA
color touch panel display; CDMA wireless technology to perform wide area network (WAN)
phone communication; Rapid Deployment.
Screens and windows pictured in this Product Reference Guide are
samples and may vary.
Page 29
Chapter Descriptions
Topics covered in this guide are as follows:
•Chapter 1, Getting Started lists the accessories for the mobile computer and explains how
to install and charge the batteries, replace the strap and start the mobile computer for the
first time.
•Chapter 2, Operating explains the physical buttons and controls on the mobile computer,
how to use the mobile computer, including instructions for powering on and resetting the
mobile computer, using the stylus and a headset, entering information and scanning.
•Chapter 3, Settings explains how to adjust settings on the mobile computer and remove
programs.
®
•Chapter 4, Communications explains how to use Microsoft
communication between the mobile computer and host computer.
•Chapter 5, Spectrum24 Configuration describes how to configure the Spectrum24 wireless
connection.
•Chapter 6, Wireless WAN - GSM/GPRS explains how to verify MC9062 service on a Global
System for Mobile Communication (GSM) wireless network and establish settings.
•Chapter 7, Wireless WAN - CDMA explains how to activate the MC9063 mobile computer
on a Code Division Multiple Access (CDMA) wireless network and establish settings.
•Chapter 8, Bluetooth explains how to use the Bluetooth wireless technology radio mode.
•Chapter 9, AirBEAM Smart explains how to set up the mobile computer to synchronize with
®
a server using the AirBEAM
Client and AirBEAM Staging applications.
•Chapter 10, Rapid Deployment Client explains how to use the Rapid Deployment Client to
facilitate software downloads to the mobile computer from a Mobility Services Platform
(MSP) Console’s FTP server.
•Chapter 11, Applications describes how to use the applications installed on the mobile
computer.
•Chapter 12, Accessories describes the accessories available for the mobile computer and
how to setup power connections and battery charging capabilities, where applicable.
•Chapter 13, Software Installation on Development PC provides instructions for installing the
Device Configuration Package (DCP) for MC9000w, the Symbol Mobility Developer Kit
(SMDK) for eVC4 and the Symbol Mobility Developer Kit (SMDK) for .NET on the host
computer.
•Chapter 14, Configuring the Mobile Computer describes how to install and use the Terminal
Configuration Manager (TCM) and Initial Program Loader (IPL).
ActiveSync® for
xxiii
Page 30
xxiv
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
•Chapter 15, Maintenance & Troubleshooting provides information to help take proper care
of the mobile computer and solve problems that may come up.
•Chapter A, Block Recognizer describes how to using the Block Recognizer to write
characters.
•Chapter B, Demo Program provides an overview of the mobile computer demo program
applications, such as scanning, imager, setup, diagnostic utilities and file management.
•Appendix C, Specifications includes a table listing the technical specifications for the mobile
computer.
•Appendix D, Keypad Maps includes tables listing key functionality for each keypad.
Notational Conventions
The following conventions are used in this document:
•“Mobile computer” refers to any Symbol terminal.
•“User” refers to anyone using an application on the mobile computer.
•“You” refers to the End User, System Administrator or Technical Support person using this
manual as a reference to install, configure, operate, maintain and troubleshoot the mobile
computer.
•Italics are used to highlight the following:
• chapters and sections in this and related documents
• dialog box, window and screen names
• drop-down list and list box names
• check box and radio button names
• icons on a screen.
•Bold text is used to highlight the following:
• key names on a keypad
• button names on a screen.
•Bullets (•) indicate:
• action items
• lists of alternatives
• lists of required steps that are not necessarily sequential.
•Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered
lists.
Page 31
Related Documents and Software
The following documents provide more information about the MC9000-K and MC9000-S mobile
computers.
•MC9000-K Quick Start Poster, p/n 72-65257-xx
•MC9000-S Quick Start Poster, p/n 72-65258-xx
•MC9000-K / MC9000-S Licensing, Patent and Regulatory Information, p/n 72-65261-xx
•Symbol Mobility Developer Kit (SMDK) Help File, p/n 72E-38880-xx
•Symbol Mobility Developer Kit for eMbedded Visual C++ v4.0 (SMDK for eVC4), available at:
http://www.symbol.com/mc9000-k and http://www.symbol.com/mc9000-s
•Symbol Mobility Developer Kit for .NET (SMDK for .NET), available at:
http://www.symbol.com/mc9000-k and http://www.symbol.com/mc9000-s
•Device Configuration Package for MC9000w (DCP for MC9000w), available at:
http://www.symbol.com/mc9000-k and http://www.symbol.com/mc9000-s.
•eConnect software, available at: http://devzone.symbol.com.
•ActiveSync software, available at: http://www.microsoft.com.
xxv
Service Information
If you have a problem with the equipment, contact the Symbol Support Center for your region. See
page xxvi for contact information. Before calling, have the model number, serial number and several
bar code symbols at hand.
Call the Support Center from a phone near the scanning equipment so that the service person can try
to talk you through the problem. If the equipment is found to be working properly and the problem is
symbol readability, the Support Center will request samples of bar codes for analysis at our plant.
If the problem cannot be solved over the phone, you may need to return the equipment for servicing.
If that is necessary, you will be given specific directions.
Symbol Technologies is not responsible for any damages incurred
during shipment if the approved shipping container is not used.
Shipping the units improperly can possibly void the warranty. If the
original shipping container was not kept, contact Symbol to have
another sent to you.
Page 32
xxvi
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Symbol Support Center
For service information, warranty information or technical assistance contact or call the Symbol
Support Center in:
United States
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, New York 11742-1300
1-800-653-5350
United Kingdom
Symbol Technologies
Symbol Place
Winnersh Triangle, Berkshire RG41 5TP
United Kingdom
0800 328 2424 (Inside UK)
+44 118 945 7529 (Outside UK)
Australia
Symbol Technologies Pty. Ltd.
432 St. Kilda Road
Melbourne, Victoria 3004
1-800-672-906 (Inside Australia)
+61-3-9866-6044 (Outside Australia)
Denmark/Danmark
Symbol Technologies AS
Dr. Neergaardsvej 3
2970 Hørsholm
7020-1718 (Inside Denmark)
+45-7020-1718 (Outside Denmark)
Finland/Suomi
Oy Symbol Technologies
Kaupintie 8 A 6
FIN-00440 Helsinki, Finland
9 5407 580 (Inside Finland)
+358 9 5407 580 (Outside Finland)
Canada
Symbol Technologies Canada, Inc.
5180 Orbitor Drive
Mississauga, Ontario, Canada L4W 5L9
1-866-416-8545 (Inside Canada)
905-629-7226 (Outside Canada)
Asia/Pacific
Symbol Technologies Asia, Inc (Singapore Branch)
230 Victoria Street #05-07/09
Bugis Junction Office Tower
Singapore 188024
Tel: +65-6796-9600
Fax: +65-6337-6488
Austria/Österreich
Symbol Technologies Austria GmbH
Prinz-Eugen Strasse 70 / 2.Haus
1040 Vienna, Austria
01-5055794-0 (Inside Austria)
+43-1-5055794-0 (Outside Austria)
Europe/Mid-East Distributor Operations
Contact your local distributor or call
+44 118 945 7360
France
Symbol Technologies France
Centre d'Affaire d'Antony
3 Rue de la Renaissance
92184 Antony Cedex, France
01-40-96-52-21 (Inside France)
+33-1-40-96-52-50 (Outside France)
2730 University Dr.
Coral Springs, FL 33065 USA
1-800-347-0178 (Inside United States)
+1-954-255-2610 (Outside United States)
954-340-9454 (Fax)
Netherlands/Nederland
Symbol Technologies
Kerkplein 2, 7051 CX
Postbus 24 7050 AA
Varsseveld, Netherlands
315-271700 (Inside Netherlands)
+31-315-271700 (Outside Netherlands)
Italy/Italia
Symbol Technologies Italia S.R.L.
Via Cristoforo Columbo, 49
20090 Trezzano S/N Navigilo
Milano, Italy
2-484441 (Inside Italy)
+39-02-484441 (Outside Italy)
Mexico/México
Symbol Technologies Mexico Ltd.
Torre Picasso
Boulevard Manuel Avila Camacho No 88
Lomas de Chapultepec CP 11000
Mexico City, DF, Mexico
5-520-1835 (Inside Mexico)
+52-5-520-1835 (Outside Mexico)
Norway/Norge
Symbol’s registered and mailing address:
Symbol Technologies Norway
Hoybratenveien 35 C
N-1055 OSLO, Norway
Symbol’s repair depot and shipping address:
Symbol Technologies Norway
Enebakkveien 123
N-0680 OSLO, Norway
+47 2232 4375
Page 34
xxviii
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
South Africa
Symbol Technologies Africa Inc.
Block B2
Rutherford Estate
1 Scott Street
Waverly 2090 Johannesburg
Republic of South Africa
11-809 5311 (Inside South Africa)
+27-11-809 5311 (Outside South Africa)
Sweden/Sverige
“Letter” address:
Symbol Technologies AB
Box 1354
S-171 26 SOLNA
Sweden
Visit/shipping address:
Symbol Technologies AB
Solna Strandväg 78
S-171 54 SOLNA
Sweden
This chapter lists the accessories for the mobile computer and explains how to install and charge the
batteries, replace the strap and start the mobile computer for the first time.
Microphone
To uc h
Screen
Indicator
LED Bar
Power
Scan
Button
Keypad
ALT
CTRL
SPACE ALPHA
ABC3DEF
12
GHI
JKL6MNO
4
5
PQRS
TUV9WXYZ
7
8
0#
BKSP
SHIFT
Power
1-3
MC9000-K
Figure 1-1. Front View: MC9000-K and MC9000-S
MC9000-S
Page 38
1-4
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Exit
Window
Headphone
Jack
Scan
Button
Battery Release
Latch
Exit
Window
Headphone
Jack
MC9000-K
MC9000-S
Figure 1-2. Side View: MC9000-K and MC9000-S
Page 39
Stylus
Strap
SIM
Housing
Cover
(MC9062
only)
Getting Started
Battery
Release
Latch
1-5
MC9000-K
MC9000-S
Figure 1-3. Back View: MC9000-K and MC9000-S
Page 40
1-6
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Unpacking the Mobile Computer
Carefully remove all protective material from around the mobile computer and save the shipping
container for later storage and shipping.
Verify that you received all equipment listed below:
•mobile computer
•lithium-ion battery
•strap, attached to the mobile computer
•stylus, in the strap stylus silo
•Regulatory Guide
•Quick Start Guide (poster).
Inspect the equipment for damage. If you are missing any equipment or if you find any damaged
equipment, contact the Symbol Technologies Support Center immediately. See page xxv for contact
information.
Page 41
Getting Started
Accessories
•Cable Adapter Module (CAM): Snap-on required to connect the following cables to the
mobile computer.
• AC line cord (country-specific) and power supply, charges the mobile computer.
• Auto charge cable, charges the mobile computer using a vehicle’s cigarette lighter.
• DEX cable, connects the mobile computer to a vending machine.
• Serial cable, adds serial communication capabilities.
• USB cable, adds USB communication capabilities.
• Printer cable, adds printer communication capabilities.
•Four Slot Charge Only Cradle: Charges the mobile computer main battery.
•Four Slot Ethernet Cradle: Charges the mobile computer main battery and synchronizes the
mobile computer with a host computer through an Ethernet connection.
•Four Slot Spare Battery Charger: Charges up to four mobile computer spare batteries.
•Headphone: Use in noisy environments.
•Holsters: Hold the mobile computer when not in use.
•Keypads (Optional): Application specific keypads.
•Magnetic Stripe Reader (MSR): Snaps on to the mobile computer and adds magstripe read
capabilities.
•Modem Module: Enables data communication between the mobile computer and a host
computer, remotely through the phone lines, and synchronizes information between the
mobile computer and a host computer.
•Multimedia Card (MMC): Provides mobile phone service provider account details for phone
service.
•Single Slot Serial/USB Cradle: Charges the mobile computer main battery and a spare
battery. It also synchronizes the mobile computer with a host computer through either a
serial or a USB connection.
•Software:
• Device Configuration Package for MC9000w (DCP for MC9000w), available at:
http://www.symbol.com/mc9000-k and http://www.symbol.com/mc9000-s.
• Symbol Mobility Developer Kit for eMbedded Visual C++ v4.0 (SMDK for eVC4), available
at: http://www.symbol.com/mc9000-k and http://www.symbol.com/mc9000-s.
• Symbol Mobility Developer Kit for .NET (SMDK for .NET), available at:
http://www.symbol.com/mc9000-k and http://www.symbol.com/mc9000-s.
1-7
Page 42
1-8
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
•Spare lithium-ion battery.
•Spare Battery Adapter: Use with the Four Slot Charge Only Cradle, Single Slot Serial/USB
Cradle and UBC Adapter for charging spare 1550 mAh batteries for the MC9000-S mobile
computer.
•Subscriber Identification Module (SIM) Card (MC9062 only): Provides pertinent phone
information such as phone number, account information, phone book, PIM data, etc. When
inserted into any GSM compatible phone, the phone is instantly personalized to the user.
•Stylus, performs pen functions.
•Stylus with tether (attaches to strap clip), performs pen functions.
•Universal Battery Charger Adapter: Adapts the UBC for use with the Series 9000 batteries.
•Vehicle Cradle: Powered by a vehicle’s 12 V or 24 V electrical system; provides power for
operating the mobile computer; provides a serial port for data communication between the
mobile computer and an external device (e.g., a printer); re-charges the mobile computer’s
battery and a spare battery.
•Wall Mounting Bracket and Shelf Slide: Use for wall mounting applications.
Getting Started
In order to start using the mobile computer for the first time:
•install the main battery
•charge the main battery and backup battery
•install the SIM card (MC9062 only)
•start the mobile computer
•configure the mobile computer.
The main battery can be charged before or after it is installed. Use one of the spare battery chargers
to charge the main battery (out of the mobile computer), or one of the cradles to charge the main
battery installed in the mobile computer.
Page 43
Getting Started
Installing and Removing the Main Battery
Installing the Main Battery
Before using the mobile computer, install a lithium-ion battery by sliding the battery into the mobile
computer as shown in Figure 1-4.
Ensure the battery is fully inserted. Two audible clicks can be heard as the battery is fully
inserted. A partially inserted battery may result in unintentional data loss.
When a battery is fully inserted in a mobile computer for the first time, upon the mobile
computer’s first power up, the device boots and powers on automatically.
1-9
Figure 1-4. Installing the Main Battery (MC9000-K Pictured)
Page 44
1-10
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Removing the Main Battery
To remove the main battery:
1.Prior to removing the battery, press the red Power button to turn off the screen. This sets
the mobile computer to suspend mode.
2.Simultaneously press both primary battery releases. The battery partially ejects from the
mobile computer.
3.Pause 3-4 seconds while the mobile computer performs battery removal shutdown.
4.Press the secondary battery release, on top of the battery, and slide the battery out of the
mobile computer.
Secondary Battery Release
Primary Battery Releases
Figure 1-5. Removing the Main Battery - MC9000-K
Page 45
Primary Battery Release
Secondary Battery
Release
Figure 1-6. Removing the Main Battery - MC9000-S
Getting Started
1-11
Page 46
1-12
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Charging the Battery
Charging the Main Battery and Memory Backup Battery
Before using the mobile computer for the first time, charge the main battery until the amber charge
indicator light in the Indicator LED bar remains lit (see Table 1-1 on page 1-13 for charge status
indications). Charge time is less than four hours. The mobile computer can be charged using a cradle,
the CAM with a charging cable, or the MSR with the appropriate power supply.
The mobile computer is equipped with a memory backup battery which automatically charges from
the fully-charged main battery. When the mobile computer is used for the first time, the backup
battery requires approximately 15 hours to fully charge. This is also true any time the backup battery
is discharged, which occurs when the main battery is removed for several hours. The backup battery
retains data in memory for at least 30 minutes when the mobile computer's main battery is removed.
When the mobile computer reaches a very low battery state, the combination of main battery and
backup battery retains data in memory for at least 72 hours.
Do not remove the main battery within the first 15 hours of use. If the main
battery is removed before the backup battery is fully charged, data may be
lost.
The following accessories can be used to charge batteries.
•Cradles: The mobile computer slips into the cradles for charging the battery in the mobile
computer (and spare batteries, where applicable). For detailed cradle setup and charging
procedures see:
• Single Slot Serial/USB Cradle on page 12-11
• Vehicle Cradle on page 12-15
• Four Slot Ethernet Cradle on page 12-28 and Four Slot Charge Only Cradles on page 12-
30.
•Accessories: The mobile computer’s snap-on accessories provide charging capability, when
used with one of the accessory charging cables. For detailed snap-on setup and charging
procedures see:
•MSR on page 12-34
•CAM on page 12-39.
•Chargers: The mobile computer’s spare battery charging accessories are used to charge
batteries that are removed from the mobile computer. For detailed spare battery charging
accessories setup and charging procedures see:
Page 47
Getting Started
• Single Slot Serial/USB Cradle on page 12-11
• Vehicle Cradle on page 12-15
• Four Slot Spare Battery Charger on page 12-32
• Universal Battery Charger (UBC) on page 12-43.
To achieve the best battery life in mobile computers with multiple radios, turn
off the radios that are not being used. This can be accomplished via the
SetDevicePower() API (refer to the SMDK Help File) or via the Control Panel
application (tap Start - 9000 Demo - Ctl Panel icon).
Charging the Main Battery
Charge the main battery in the mobile computer using a cradle, the CAM with a charging cable, or
the MSR with the appropriate power supply.
1.Ensure the accessory used to charge the main battery is connected to the appropriate power
source (see Chapter 12, Accessories for setup information).
2.Insert the mobile computer into a cradle or attach the appropriate snap-on module.
3.The mobile computer starts to charge automatically. The amber charge LED, in the Indicator
LED Bar, lights to show the charge status. See Table 1-1 for charging indications.
The main battery usually fully charges in less than four hours.
1-13
Table 1-1. Mobile Computer LED Charge Indicators
LEDIndication
OffMobile computer not in cradle/CAM/MSR; mobile computer not placed correctly;
charger is not powered.
Fast Blinking AmberError in charging; check placement of the mobile computer.
Slow Blinking AmberMobile computer is charging.
Solid AmberCharging complete.
Note: When the battery is initially inserted in the mobile computer, the amber LED
flashes once if the battery power is low or the battery is not fully inserted.
Page 48
1-14
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Charging Spare Batteries
The mobile computer has four accessories that can be used to charge spare batteries.
•Four Slot Spare Battery Charger
•Single Slot Serial/USB Cradle
•UBC Adapter
•Vehicle Cradle.
To charge a spare battery:
1.Ensure the accessory used to charge the spare battery is connected to the appropriate power
source (see Chapter 12, Accessories for setup information).
2.Insert the spare battery into the accessory’s spare battery charging slot with the charging
contacts facing down (over the charging pins) and gently press down on the battery to
ensure proper contact.
3.The battery starts to charge automatically. The amber charge LED on the accessory lights to
show the charge status. See Chapter 12, Accessories for charging indications for the
accessory.
The battery usually fully charges in less than four hours.
An adapter is required to charge an MC9000-S spare battery in the spare
battery well.
SIM Card (MC9062)
The Subscriber Identification Module (SIM) card, or smart card, is required for GSM/GPRS phone
service and must be obtained from the phone service provider. The card fits into the mobile computer
and can contain the following information:
•Mobile phone service provider account details.
•Information regarding service access and preferences.
•Contact information, which can be moved to Contacts on the mobile computer.
•Any additional services to which the user may have subscribed.
Page 49
For more information about SIM cards, refer to the mobile phone service
provider's documentation.
To install the SIM card:
1.Power off the mobile computer.
2.Remove the SIM housing cover on the back of the mobile computer.
SIM
Housing Cover
Getting Started
1-15
Figure 1-7. Removing SIM Cover
3.Unscrew and remove the SIM holder clamp.
SIM Holder
Clamp
Figure 1-8. Removing SIM Holder Clamp
Page 50
1-16
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
4.Unlock the SIM holder by sliding the metal clip to the open position. Lift the SIM holder.
SIM Holder
Figure 1-9. Unlock SIM Case
5.Insert the SIM card, as shown in Figure 1-10, with the cut edge of the card facing out and
the contacts facing the contacts in the SIM housing. Lower the SIM holder.
Figure 1-10. Inserting the SIM Card
6.Lock the metal clip by sliding it to the closed position.
7.Replace the SIM holder clamp with one screw.
Page 51
Getting Started
8.Replace the SIM housing cover with one screw.
Figure 1-11. Locking the SIM Card Housing
9.Tap Start - Phone - Tools - Options - Network tab and verify that the service provider appears
in the Current network: field.
10. Make a call to verify connection.
For detailed information about WWAN activation and settings, see Chapter
6, Wireless WAN - GSM/GPRS and Chapter 7, Wireless WAN - CDMA. See
Using the Phone (MC9062/MC9063 Only) on page 2-63 for information about
using the phone and services.
1-17
Stylus
Use the mobile computer stylus for selecting items and entering information. The stylus functions as
a mouse.
•Tap: Touch the screen once with the stylus to press option buttons and open menu items.
•Tap and Hold: Tap and hold the stylus on an item to see a list of actions available for that
item. On the pop-up menu that appears, tap the action to perform.
•Drag: Hold the stylus on the screen and drag across the screen to select text and images.
Drag in a list to select multiple items.
The stylus’ holder is located in the mobile computer’s strap.
Strap
The strap may be moved to either the left or right side of the mobile computer to suit user preferences.
Page 52
1-18
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
MC9000-K Strap
To reposition the MC9000-K Strap:
1.Disengage the upper portion of the strap by disconnecting the button from the loop
connector.
2.Loosen the loop from the bottom of the strap and slide the strap through.
3.Slide the loop out of the connector post.
Figure 1-12. Repositioning the MC9000-K Strap
4.Reverse the procedure to re-attach the strap. Two strap connectors are provided on the
mobile computer’s main body. The strap may be attached to either connector.
Page 53
Getting Started
MC9000-S Strap
To reposition the MC9000-S Strap, attach the MC9000-S strap to either the left or right side of the
mobile computer to suit user preferences.
Figure 1-13. Repositioning the MC9000-S Strap
To remove the MC9000-S strap:
1.Disengage the upper portion of the strap by sliding it through the clip connector.
2.Unscrew the two screws on either side of the mobile computer.
1-19
Figure 1-14. Removing the MC9000-S Strap
3.Reverse the procedure to re-attach the strap.
Page 54
1-20
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Starting the Mobile Computer
Press the Power button to turn on the mobile computer. If the mobile computer does not power on,
perform a cold boot. See Resetting the Mobile Computer on page 2-92.
When a battery is fully inserted in a mobile computer for the first time, upon the mobile
computer’s first power up, the device boots and powers on automatically.
When the mobile computer is powered on for the first time, it initializes its system. The Symbol splash
screen (Figure 1-15) appears for a short period of time followed by the Microsoft
®
Windows®
Powered Pocket PC window.
Figure 1-15. Symbol Splash Screen
Remove the stylus from the strap and tap the Microsoft® Windows® Powered Pocket PC window
with the stylus to display align screen (Figure 1-16), where the screen is calibrated. Note that these
windows also appear every time a cold boot is performed.
Page 55
Getting Started
Calibrating the Screen
To calibrate the screen so the cursor on the touch screen aligns with the tip of the stylus:
1.Using the stylus, carefully press and briefly hold the tip of stylus on the center of each target
that appears on the screen.
Figure 1-16. Align Screen
1-21
To re-calibrate the screen at anytime, press FUNC + Esc on the mobile
computer to launch the calibration screen application.
Page 56
1-22
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
2.Follow the directions on the screen which lead you through a simple exercise illustrating
how to use the stylus and pop-up menus.
Figure 1-17. Using Pop-up Menus
3.Use the drop-down list to set your time zone, and tap Next.
Figure 1-18. Setting Time Zone
4.Tap the Complete screen to complete the initial setup.
Page 57
Getting Started
5.The Today screen appears. (See Today Screen on page 2-33 for information about using the
Today screen.)
Figure 1-19. Today Screen
Setting Time and Date
The Time and Date window does not appear after setting the time zone. Tap Start - Settings - System
tab - Clock icon to use the clock control panel applet to set the time and date after a cold boot.
1-23
Figure 1-20. Setting Time and Date
Page 58
1-24
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
See Clock on page 3-36 for details about setting time and date.
Checking Battery Status
To check whether the main battery or backup battery in the mobile computer is charged, tap Start Settings - System tab - Power icon to display the Battery Status window.
Figure 1-21. Battery Status Screen
To save battery power, set the mobile computer to turn off after a specified number of minutes. See
Power on page 3-44 to set power management options.
Page 59
Getting Started
Configuring the Mobile Computer
See the following chapters to configure the mobile computer:
•To customize the mobile computer settings, see Chapter 3, Settings.
•To set up ActiveSync to synchronize the mobile computer with the host computer, see
Chapter 4, Communications.
•To configure the mobile computer for Spectrum24, see Chapter 5, Spectrum24
Configuration.
•To configure the mobile computer for Wireless WAN, see Chapter 6, Wireless WAN - GSM/
GPRS and Chapter 7, Wireless WAN - CDMA.
•To set up AirBEAM to synchronize the mobile computer with the host server, see Chapter 9,
AirBEAM Smart.
•To configure the mobile computer using the Rapid Deployment Client, see Chapter 10, Rapid
Deployment Client.
•To install development software on the development PC, see Chapter 13, Software
Installation on Development PC.
•To configure the mobile computer using the Terminal Configuration Manager, see Chapter
14, Configuring the Mobile Computer.
1-25
Page 60
1-26
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Introduction
This chapter explains the physical buttons and controls on the mobile computer, how to use the
mobile computer, including instructions for powering on and resetting the mobile computer, using the
stylus and a headset, entering information and scanning.
Keypads
Each of the mobile computers have interchangeable modular keypads:
•28-key keypad (MC9000-K)
•43-key keypad (MC9000-K)
•53-key keypad (MC9000-K)
•28-key keypad (MC9000-S)
•38-key numeric/function keypad (MC9000-S)
•38-key alpha/shifted numeric keypad (MC9000-S).
The modular keypads can be changed in the field, as necessary, to support specialized applications.
See Keypads on page 12-7 for installation and removal procedures.
For detailed keypad information, including ASCII values and VK codes, see
Appendix D, Keypad Maps.
For information about using the soft keyboard input panel, see Entering Information
Using the Input Panel on page 2-46.
Page 65
Operating
28-Key Keypad (MC9000-K)
The 28-key keypad contains a Power button, application keys, scroll keys and function keys. The
keypad is color-coded to indicate the alternate function key (blue) values. Note that keypad functions
can be changed by an application so the mobile computer’s keypad may not function exactly as
described. See Table 2-1 on page 2-6 for key and button descriptions and Table 2-7 on page 2-29 for
the keypad’s special functions.
ALT
CTRL
SPACEALPHA
2-5
ABC3DEF
12
GHI
4
PQRS
7
JKL
5
TUV
8
MNO
6
WXYZ
BKSP
SHIFT
9
0#
Figure 2-1. MC9000-K 28-Key Keypad
Page 66
2-6
.
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Table 2-1. MC9000-K: 28-Key Descriptions
KeyDescription
Power (red)Powers the mobile computer on and off.
Performs a warm boot and a cold boot. See Resetting the Mobile Computer on page 2-92
for information about performing a warn and cold boot.
Green/Red DotWWAN Mobile Computers:
Green/Red dot keys operate on MC9062/MC9063 phone devices.
Green dot: press to display the phone keypad window or to dial a phone number (from
the phone keypad window).
Red dot: press on phone keypad window to stop dialing or end a call.
Non-WWAN Mobile Computers:
To use a key as an application key (APP key) on the keyboard, a new keyboard remap table
must be created and installed. However, the Green/Red dot keys can be remapped as
APP keys through the registry.
Create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD]
"GreenKeyOverride" = dword: xx, where xx is the new APP key code.
"RedKeyOverride" = dword: yy, where yy is the new APP key code.
Copy the registry file to the \Platform folder, then cold boot the mobile computer.
This sends an APP key code, instead of their original key codes, when the green or red
dot key is pressed.
Scan (yellow)Scan key - used for scanning applications, this key has the same function as the right Scan
button.
Scroll Up and DownMoves up and down from one item to another.
Increases/decreases specified values.
Scroll Left and RightMoves left and right from one item to another.
Increases/decreases specified values.
ESCExits the current operation.
One/Star Produces the number one in default state.
Alphanumeric In default state, produces the numeric value on the key.
GHI5JKL6MNO
4
SPACE/BKSPSpace and backspace functions.
BKSP
SPACE
CTRL (Control)Press and release the CTRL key to activate the keypad alternate CTRL functions. The
LED
In Alpha state, produces the lower case alphabetic characters on the key. Each key press
. . .
produces the next alphabetic character in sequence. For example, press and release the
ALPHA key and then press the ‘4’ key once to produce the letter ‘g’; press and release the
ALPHA key and then press the ‘4’ key three times to produce the letter ‘i’.
When the SHIFT key is pressed in Alpha state, the upper case alphabetic characters on the
key are produced. For example, press and release the ALPHA key, press and release the
SHIFT key and then press the ‘4’ key once to produce the letter ‘G’; press and release the
ALPHA key, press and release the SHIFT key and then press the ‘4’ key three times to
produce the letter ‘I’.
keypad LED lights.
2-7
ALPHAPress and release the ALPHA key to activate the keypad alternate functions (shown on the
LED
keypad in blue). The keypad LED lights. Press and release the ALPHA key again to return
to the normal keypad functions.
Function (blue)Press and release the blue function key to activate the keypad alternate functions (shown
on the keypad in blue). The keypad LED lights.
LED
SHIFTPress and release the SHIFT key to activate the keypad alternate SHIFT functions. Press
and release the SHIFT key again to return to the normal keypad functions.
SHIFT
Page 68
2-8
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
The default behavior of the Enter (Return) key sends an extra character, which causes a
Microsoft Word or Notes application to exit. To make the applications work properly,
create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\#KeyKeypad]
"SpecialEnterTabKey" = dword:0
where #keyKeypad = 28KEY, 38KEY, 43KEY or 53KEY (i.e., the number of keys on the
keypad). Copy the registry file to the \Platform folder, then cold boot the mobile computer.
Period/Decimal Point In default state, produces a period for alpha entries and a decimal point for numeric
entries.
In function key state, produces an asterisk.
When the SHIFT key is pressed in function key state, produces an asterisk.
Zero In default state, produces a zero.
In Alpha state, produces a space.
0
Pound Produces a pound/number sign.
#
For detailed keypad information, including ASCII values and VK codes, see
Appendix D, Keypad Maps.
For information about using the soft keyboard input panel, see Entering
Information Using the Input Panel on page 2-46.
Page 69
Operating
43-Key Keypad (MC9000-K)
The 43-key keypad contains a Power button, application keys, scroll keys and a function key. The
keypad is color-coded to indicate the alternate function key (blue) values and the alternate ALPHA key
(orange) values. Note that keypad functions can be changed by an application so the mobile
computer’s keypad may not function exactly as described. See Table 2-2 on page 2-10 for key and
button descriptions and Table 2-7 on page 2-29 for the keypad’s special functions.
..
2-9
Figure 2-2. MC9000-K 43-Key Keypad
Page 70
2-10
.
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Table 2-2. MC9000-K: 43-Key Descriptions
KeyDescription
Power (red) Powers the mobile computer on and off.
Performs a warm boot and a cold boot. See Resetting the Mobile Computer on page 2-92 for
information about performing a warn and cold boot.
Green/Red DotWWAN Mobile Computers:
Green/Red dot keys operate on MC9062/MC9063 phone devices.
Green dot: press to display the phone keypad window or to dial a phone number (from the
phone keypad window).
Red dot: press on phone keypad window to stop dialing or end a call.
Non-WWAN Mobile Computers:
To use a key as an application key (APP key) on the keyboard, a new keyboard remap table
must be created and installed. However, the Green/Red dot keys can be remapped as APP
keys through the registry.
Create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD]
"GreenKeyOverride" = dword: xx, where xx is the new APP key code.
"RedKeyOverride" = dword: yy, where yy is the new APP key code.
Copy the registry file to the \Platform folder, then cold boot the mobile computer.
This sends an APP key code, instead of their original key codes, when the green or red dot
key is pressed.
Scan (yellow)Scan key - used for scanning applications, this key has the same function as the right Scan
button.
Scroll Up and DownMoves up and down from one item to another.
Increases/decreases specified values.
Scroll Left and RightMoves left and right from one item to another.
Numeric/AlphaNumber or alpha value depending on the state of the ALPHA key.
. . .
Alpha/ApplicationThese keys can have an application assigned to the function value and have an alpha value
assigned when used with the ALPHA function key.
. . .
F6 and F7 keys cannot be remapped and are dedicated by the Operating System to control
volume level. When these keys are pressed, Shell.exe traps them and displays the volume
adjustment window. To get these keys to an application, call GXOpenInput() at the beginning
of the application and call GXCloseInput() at the end of the application. This redirects all of
the key events to an application, including the F6 and F7 keys.
Note: Other applications cannot receive any key event until GXCloseInput() is called. For
example, if the customer is using the APP1 key to run Calc.exe, this is disabled during this
period.
Function (blue) Press and release the blue function key to activate the keypad alternate functions (shown on
LED
the keypad in blue). The keypad LED lights.
2-11
CTRL (Control)Press and release the CTRL key to activate the keypad alternate CTRL functions. The keypad
LED
ALTPress and release the ALT key to activate the keypad ALT (alternate) functions. Press and
ALPHA (orange)The default keypad mode is the num-lock (number lock) mode. Press the orange ALPHA key
LED
SHIFTPress and release the SHIFT key to activate the keypad alternate SHIFT functions. Press and
LED lights.
release the ALT key again to return to the normal keypad functions.
to de-activate the num-lock mode and to access the alternate ALPHA characters (shown on
the keypad in orange).
release the SHIFT key again to return to the normal keypad functions.
Page 72
2-12
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Period/Decimal PointProduces a period for alpha entries, a decimal point for numeric entries and the alphabetic
character X when the ALPHA function key is activated.
Star Produces an asterisk and the alphabetic character Z when the ALPHA function key is
activated.
ENT (Enter)Executes a selected item or function.
The default behavior of the Enter (Return) key sends an extra character, which causes a
Microsoft Word or Notes application to exit. To make the applications work properly, create
a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\#KeyKeypad]
"SpecialEnterTabKey" = dword:0
where #keyKeypad = 28KEY, 38KEY, 43KEY or 53KEY (i.e., the number of keys on the keypad).
Copy the registry file to the \Platform folder, then cold boot the mobile computer.
For detailed keypad information, including ASCII values and VK codes, see
Appendix D, Keypad Maps.
For information about using the soft keyboard input panel, see Entering
Information Using the Input Panel on page 2-46.
Page 73
Operating
53-Key Keypad (MC9000-K)
There are two physical configurations of the 53-key keypad, however both of the keypads are
functionally identical. The 53-key keypad contains a Power button, application keys, scroll keys and
function keys. The keypad is color-coded to indicate the alternate function key (blue) values. Note that
keypad functions can be changed by an application so the mobile computer’s keypad may not function
exactly as described. See Table 2-3 on page 2-14 for key and button descriptions and Table 2-7 on
page 2-29 for the keypad’s special functions.
2-13
Figure 2-3. MC9000-K 53-Key Keypad
Page 74
2-14
.
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Table 2-3. MC9000-K: 53-Key Descriptions
KeyDescription
Power (red)Powers the mobile computer on and off.
Performs a warm boot and a cold boot. See Resetting the Mobile Computer on page
2-92 for information about performing a warn and cold boot.
Green/Red DotWWAN Mobile Computers:
Green/Red dot keys operate on MC9062/MC9063 phone devices.
Green dot: press to display the phone keypad window or to dial a phone number
(from the phone keypad window).
Red dot: press on phone keypad window to stop dialing or end a call.
Non-WWAN Mobile Computers:
To use a key as an application key (APP key) on the keyboard, a new keyboard remap
table must be created and installed. However, the Green/Red dot keys can be
remapped as APP keys through the registry.
Create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD]
"GreenKeyOverride" = dword: xx, where xx is the new APP key code.
"RedKeyOverride" = dword: yy, where yy is the new APP key code.
Copy the registry file to the \Platform folder, then cold boot the mobile computer.
This sends an APP key code, instead of their original key codes, when the green or red
dot key is pressed.
Scan (yellow)Scan key - used for scanning applications, this key has the same function as the right
Scan button.
Scroll Up and DownMoves up and down from one item to another.
Increases/decreases specified values.
Scroll Left and RightMoves left and right from one item to another.
Increases/decreases specified values.
ESCExits the current operation.
Alpha Use the alpha keys for alphabetic characters.
Numeric/ApplicationNumeric value keys - can have applications assigned with function key(s).
F6 and F7 keys cannot be remapped and are dedicated by the Operating System to
. . .
control volume level. When these keys are pressed, Shell.exe traps them and displays
the volume adjustment window. To get these keys to an application, call
GXOpenInput() at the beginning of the application and call GXCloseInput() at the end
of the application. This redirects all of the key events to an application, including the
F6 and F7 keys.
Note: Other applications cannot receive any key event until GXCloseInput() is called.
For example, if the customer is using the APP1 key to run Calc.exe, this is disabled
during this period.
Function (blue)Press and release the blue function key to activate the keypad alternate functions
LED
CTRL (Control)Press and release the CTRL key to activate the keypad alternate CTRL functions. The
LED
(shown on the keypad in blue). The keypad LED lights.
keypad LED lights.
2-15
SHIFTPress and release the SHIFT key to activate the keypad alternate SHI FT functions.Press
and release the SHIFT key again to return to the normal keypad functions.
Period/Decimal Point Produces a period for alpha entries and a decimal point for numeric entries.
Star Produces an asterisk.
Page 76
2-16
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
The default behavior of the Enter (Return) key sends an extra character, which causes
a Microsoft Word or Notes application to exit. To make the applications work properly,
create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\#KeyKeypad]
"SpecialEnterTabKey" = dword:0
where #keyKeypad = 28KEY, 38KEY, 43KEY or 53KEY (i.e., the number of keys on the
keypad). Copy the registry file to the \Platform folder, then cold boot the mobile
computer.
For detailed keypad information, including ASCII values and VK codes, see
Appendix D, Keypad Maps.
For information about using the soft keyboard input panel, see Entering
Information Using the Input Panel on page 2-46.
Page 77
Operating
28-Key Keypad (MC9000-S)
The 28-key keypad contains a Power button, application keys, scroll keys and function keys. The
keypad is color-coded to indicate the alternate function key (blue) values. Note that keypad functions
can be changed by an application so the mobile computer’s keypad may not function exactly as
described. See Table 2-4 on page 2-18 for key and button descriptions and Table 2-7 on page 2-29 for
the keypad’s special functions.
2-17
.
ALT
CTRL
GHI
PQRS
SPACEALPHA
12
4
7
ABC
JKL
5
TUV9WXYZ
8
0#
DEF
3
MNO
6
.
BKSP
SHIFT
Figure 2-4. MC9000-S 28-Key Keypad
Page 78
2-18
.
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Table 2-4. MC9000-S: 28-Key Descriptions
KeyDescription
Power (red)Powers the mobile computer on and off.
Performs a warm boot and a cold boot. See Resetting the Mobile Computer on page 2-
92 for information about performing a warn and cold boot.
Green/Red DotWWAN Mobile Computers:
Green/Red dot keys operate on MC9062/MC9063 phone devices.
Green dot: press to display the phone keypad window or to dial a phone number (from
the phone keypad window).
Red dot: press on phone keypad window to stop dialing or end a call.
Non-WWAN Mobile Computers:
To use a key as an application key (APP key) on the keyboard, a new keyboard remap
table must be created and installed. However, the Green/Red dot keys can be
remapped as APP keys through the registry.
Create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD]
"GreenKeyOverride" = dword: xx, where xx is the new APP key code.
"RedKeyOverride" = dword: yy, where yy is the new APP key code.
Copy the registry file to the \Platform folder, then cold boot the mobile computer.
This sends an APP key code, instead of their original key codes, when the green or red
dot key is pressed.
Scan (yellow)Scan key - used for scanning applications, this key has the same function as the right
Scan button.
Scroll Up and DownMoves up and down from one item to another.
Increases/decreases specified values.
Scroll Left and RightMoves left and right from one item to another.
Increases/decreases specified values.
ESCExits the current operation.
One/Star Produces the number one in default state.
Alphanumeric In default state, produces the numeric value on the key.
GHI5JKL6MNO
4
SPACE/BKSPSpace and backspace functions.
BKSP
SPACE
CTRL (Control)Press and release the CTRL key to activate the keypad alternate CTRL functions. The
LED
In Alpha state, produces the lower case alphabetic characters on the key. Each key press
. . .
produces the next alphabetic character in sequence. For example, press and release the
ALPHA key and then press the ‘4’ key once to produce the letter ‘g’; press and release
the ALPHA key and then press the ‘4’ key three times to produce the letter ‘i’.
When the SHIFT key is pressed in Alpha state, the upper case alphabetic characters on
the key are produced. For example, press and release the ALPHA key, press and release
the SHIFT key and then press the ‘4’ key once to produce the letter ‘G’; press and release
the ALPHA key, press and release the SHIFT key and then press the ‘4’ key three times
to produce the letter ‘I’.
keypad LED lights.
2-19
ALPHAPress and release the ALPHA key to activate the keypad alternate functions (shown on
LED
the keypad in blue). The keypad LED lights. Press and release the ALPHA key again to
return to the normal keypad functions.
Function (blue)Press and release the blue function key to activate the keypad alternate functions
(shown on the keypad in blue). The keypad LED lights.
LED
SHIFTPress and release the SHIFT key to activate the keypad alternate SHIFT functions. Press
and release the SHIFT key again to return to the normal keypad functions.
SHIFT
Page 80
2-20
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
The default behavior of the Enter (Return) key sends an extra character, which causes a
Microsoft Word or Notes application to exit. To make the applications work properly,
create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\#KeyKeypad]
"SpecialEnterTabKey" = dword:0
where #keyKeypad = 28KEY, 38KEY, 43KEY or 53KEY (i.e., the number of keys on the
keypad). Copy the registry file to the \Platform folder, then cold boot the mobile
computer.
Period/Decimal Point In default state, produces a period for alpha entries and a decimal point for numeric
entries.
In function key state, produces an asterisk.
When the SHIFT key is pressed in function key state, produces an asterisk.
Zero In default state, produces a zero.
In Alpha state, produces a space.
0
Pound Produces a pound/number sign.
#
For detailed keypad information, including ASCII values and VK codes, see
Appendix D, Keypad Maps.
For information about using the soft keyboard input panel, see Entering
Information Using the Input Panel on page 2-46.
Page 81
Operating
38-Key Numeric/Function Keypad (MC9000-S)
The 38-key numeric/function keypad contains a Power button, application keys, scroll keys and a
function key. The keypad is color-coded to indicate the alternate function key (blue) values and the
alternate alpha key (orange) values. Note that keypad functions can be changed by an application so
the mobile computer’s keypad may not function exactly as described. See Table 2-4 on page 2-18 for
key and button descriptions and Table 2-7 on page 2-29 for the keypad’s special functions.
Performs a warm boot and a cold boot. See Resetting the Mobile Computer on page 2-92
for information about performing a warn and cold boot.
Green/Red DotWWAN Mobile Computers:
Green/Red dot keys operate on MC9062/MC9063 phone devices.
Green dot: press to display the phone keypad window or to dial a phone number (from
the phone keypad window).
Red dot: press on phone keypad window to stop dialing or end a call.
Non-WWAN Mobile Computers:
To use a key as an application key (APP key) on the keyboard, a new keyboard remap
table must be created and installed. However, the Green/Red dot keys can be remapped
as APP keys through the registry.
Create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD]
"GreenKeyOverride" = dword: xx, where xx is the new APP key code.
"RedKeyOverride" = dword: yy, where yy is the new APP key code.
Copy the registry file to the \Platform folder, then cold boot the mobile computer.
This sends an APP key code, instead of their original key codes, when the green or red dot
key is pressed.
Scan (yellow)Scan key - used for scanning applications, this key has the same function as the right
CTRL (Control)Use to produce CTRL characters or functions.
LED
SHIFTPress and release the SHIFT key to activate the keypad alternate SHIFT functions. Press
Alpha-lock (orange)Press and release the orange alpha-lock key to activate the keypad alternate alpha-lock
LED
Function (blue) Press and release the blue function key to activate the keypad alternate functions (shown
LED
Special Function/AlphaProgrammable function (F1, F2, F3 . . . ) by default.
Use FUNC - CTRL to produce ALT characters or functions.
and release the SHIFT key again to return to the normal keypad functions.
Use with the orange alpha-lock key for alpha character value.
functions (shown on the keypad in orange). The keypad LED lights. Press and release the
orange alpha-lock key again to return to the default keypad functions.
on the keypad in blue). The keypad LED lights. Press and release the blue function key
again to return to the normal keypad functions.
Use with the orange key for alpha character value.
. . .
Use the blue key for function value.
2-23
SPACESPACE function by default.
Use with the orange key for alpha character value.
Use the blue key for function value.
Keypad BacklightKeypad backlight by default.
Use with the orange key for alpha character value.
Use the blue key for function value.
Display BacklightDisplay backlight by default.
Use with the orange alpha-lock key for alpha character value.
Use the blue function key for function value.
BKSPBackspace function by default.
Use with the orange alpha-lock key for alpha character value.
Use the blue function key for function value.
NumericUse for numeric characters by default.
Use with the orange alpha-lock key for alpha character value.
. . .
Use the blue function key for function value.
Page 84
2-24
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Use with the orange alpha-lock key for alpha character value.
Use the blue function key for function value.
Period/Decimal PointIn default state, produces a period for alpha entries and a decimal point for numeric
entries.
Use with the orange alpha-lock key for alpha character value.
Star In default state, produces an asterisk.
Use with the orange alpha-lock key for alpha character value.
ENT (Enter)Executes a selected item or function.
The default behavior of the Enter (Return) key sends an extra character, which causes a
Microsoft Word or Notes application to exit. To make the applications work properly,
create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\#KeyKeypad]
"SpecialEnterTabKey" = dword:0
where #keyKeypad = 28KEY, 38KEY, 43KEY or 53KEY (i.e., the number of keys on the
keypad). Copy the registry file to the \Platform folder, then cold boot the mobile computer.
ComaIn default state, produces a coma.
Use with the orange key for alpha character value.
For detailed keypad information, including ASCII values and VK codes, see
Appendix D, Keypad Maps.
For information about using the soft keyboard input panel, see Entering
Information Using the Input Panel on page 2-46.
Page 85
Operating
38-Key Alpha/Shifted Numeric Keypad (MC9000-S)
The 38-key alpha/shifted numeric keypad contains a Power button, application keys, scroll keys and
a function key. The keypad is color-coded to indicate the alternate function key (blue) values and the
alternate numeric key (orange) values. Note that keypad functions can be changed by an application
so the mobile computer’s keypad may not function exactly as described. See Table 2-4 on page 2-18
for key and button descriptions and Table 2-7 on page 2-29 for the keypad’s special functions.
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Table 2-6. MC9000-S: 38-Key Alpha/Shifted Numeric
Keypad Descriptions
KeyDescription
Power (red)Powers the mobile computer on and off.
Performs a warm boot and a cold boot. See Resetting the Mobile
Computer on page 2-92 for information about performing a warn and
cold boot.
Green/Red DotWWAN Mobile Computers:
Green/Red dot keys operate on MC9062/MC9063 phone devices.
Green dot: press to display the phone keypad window or to dial a
phone number (from the phone keypad window).
Red dot: press on phone keypad window to stop dialing or end a call.
Non-WWAN Mobile Computers:
To use a key as an application key (APP key) on the keyboard, a new
keyboard remap table must be created and installed. However, the
Green/Red dot keys can be remapped as APP keys through the
registry.
Create a registry file with the following entry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD]
"GreenKeyOverride" = dword: xx, where xx is the new APP key code.
"RedKeyOverride" = dword: yy, where yy is the new APP key code.
Copy the registry file to the \Platform folder, then cold boot the mobile
computer.
This sends an APP key code, instead of their original key codes, when
the green or red dot key is pressed.
Scan (yellow)Scan key - used for scanning applications, this key has the same
function as the right Scan button.
Scroll Up and LeftMoves up by default.
Use with the orange num-lock key to move left.
Scroll Down and RightMoves down by default.
Use with the orange num-lock key to move right.
Page 87
Operating
Table 2-6. MC9000-S: 38-Key Alpha/Shifted Numeric
Keypad Descriptions (Continued)
KeyDescription
ESCExits the current operation.
CAPUse to produce capital alpha characters.
LED
SPACEIn default state, produces a space function.
Num-lock (orange)Press and release the orange num-lock key to activate the keypad
LED
Function (blue) Press and release the blue function key to activate the keypad alternate
LED
The keypad LED lights.
Use with the orange num-lock key for the backspace function.
alternate num-lock functions (shown on the keypad in orange). The
keypad LED lights. Press and release the orange num-lock key again to
return to the default keypad functions.
functions (shown on the keypad in blue). The keypad LED lights. Press
and release the blue function key again to return to the normal keypad
functions.
2-27
Alpha Use for alpha characters by default.
Use with the orange num-lock key for numeric character values.
. . .
Use the blue function key for function values.
ENT (Enter)Executes a selected item or function.
The default behavior of the Enter (Return) key sends an extra character,
which causes a Microsoft Word or Notes application to exit. To make
the applications work properly, create a registry file with the following
entry:
"SpecialEnterTabKey" = dword:0
where #keyKeypad = 28KEY, 38KEY, 43KEY or 53KEY (i.e., the number
of keys on the keypad). Copy the registry file to the \Platform folder, then
cold boot the mobile computer.
Page 88
2-28
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
For detailed keypad information, including ASCII values and VK codes, see
Appendix D, Keypad Maps.
For information about using the soft keyboard input panel, see Entering
Information Using the Input Panel on page 2-46.
Page 89
Operating
Keypad Special Functions
The keypad special functions are color coded on the keypads. For example, on the 53-key keypad, the
display backlight icon is blue indicating that the blue function key must be selected first to access the
display backlight. On the 43-key keypad, the display backlight icon is white indicating that the display
backlight is the default value for that key. Use of display and keypad backlighting can significantly
reduce battery life.
Mobile computers with color screens do not have contrast settings.
Table 2-7. Keypad Special Functions
38-Key
Icon
28-Key
Keystrokes
Blue
function key
and #
or
Blue
function key/
SHIFT and #
Alpha/
Shifted
Numeric
Keystrokes
Blue
function key
and V
38-Key
Numeric/
Function
Keystrokes
43-Key
Keystrokes
53-Key
KeystrokesSpecial Function
Blue
function key
and Z
Turns on and off the display
backlight.
2-29
Blue
function key
and 0
or
Blue
function key/
SHIFT and 0
Blue
function key
and 1
or
Blue
function key/
SHIFT and 1
Blue
function key
and Y
Blue
function key
and A
Blue
function key
and X
Blue
function key
and F1
Blue function
key and F1
Blue
function key
and D
Turns on and off the keypad
backlight.
Monochrome units: Increases
display contrast.
Color units: Increases display
backlight intensity.
Page 90
2-30
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Table 2-7. Keypad Special Functions (Continued)
38-Key
Icon
28-Key
Keystrokes
Alpha/
Shifted
Numeric
Keystrokes
38-Key
Numeric/
Function
Keystrokes
43-Key
Keystrokes
53-Key
KeystrokesSpecial Function
Blue
function key
and 4
or
Blue
function key/
SHIFT and 4
Blue
function key
and 3
or
Blue
function key/
SHIFT and 3
Blue
function key
and 6
or
Blue
function key/
SHIFT and 6
Blue
*
function key
and CTRL
Not
available
Blue
function key
and E
Blue
function key
and D
Blue
function key
and H
Blue
function key
and X
Blue
function key
and U
Blue
function key
and F5
Blue
function key
and F4
Blue
function key
and F8
ALT
function key
Not
available
Blue function
key and F5
Blue function
key and F4
Blue function
key and F8
Not
Available
Blue function
key and U
Blue
function key
and I
Blue
function key
and H
Blue
function key
and M
Blue
function key
and CTRL
Not
available
Monochrome units: Decreases
display contrast.
Color units: Increases display
backlight intensity.
Increases scan decode beeper
volume.
Decreases scan decode beeper
volume.
Enables Alt keypad functions.
Sends TAB character (forward
tab).
Using the Power Button
Press the red Power button to turn the mobile computer screen on and off (suspend mode). The
mobile computer is on when the screen is on and the mobile computer is in suspend mode when the
screen is off. For more information, see Starting the Mobile Computer on page 1-20.
Page 91
Operating
The Power button is also used to reset the mobile computer by performing a warm or cold boot.
•Warm Boot (Soft Reset) - Resets the mobile computer.
•Cold Boot (Hard Reset) - Resets the mobile computer, removes all added applications and
restores all factory default settings.
Applications that are added to the Application and Platform folders are not
removed when a cold boot is performed on the mobile computer. Application
and Platform folders are in flash memory.
For information about booting the mobile computer, see Resetting the Mobile Computer on page 2-92.
2-31
Page 92
2-32
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Using a Headset
Use a stereo headset to listen to mono audio playback. To use a headset, plug the headset jack into
the audio connector on the top of the mobile computer. Ensure that the mobile computer’s volume is
set appropriately before putting the headset on. When a headset is plugged into the jack, the speaker
is muted.
Figure 2-7. Using a Headset (MC9000-K Pictured)
For WWAN-enabled mobile computers, voice communication is only available through
the headset. For these mobile computers, Symbol recommends a 2.5mm jack headset,
p/n 50-11300-050.
Page 93
Operating
Today Screen
When you turn on the mobile computer for the first time each day (or after 4 hours of inactivity), the
Today screen appears. You can also display it by tapping Start - Today. On the Today screen, you can
see important information for the day.
2-33
Tap to switch to
a program
Tap to create a new itemTap to view connection status
Tap to change volume or mute all sounds
Tap to change the date and time
Tap to open an item
The day at a glance
Figure 2-8. Today Screen
The Today screen may vary depending on the mobile computer configuration.
The Toda y screen can be customized. Tap Start - Settings - Today icon. Use the Appearance tab to
customize the background and the Items tab to change the list and order of items that appear on the
screen.
Page 94
2-34
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Using the Navigation Bar and Command Bar
The navigation bar at the top of the screen displays the active program, various status icons (see
Table 2-8) and current time. It also allows you to select programs and close screens.
Use the command bar (task tray) at the bottom of the screen to perform tasks in programs. The
command bar includes menu names, buttons and the Input Panel button. It can also include icons of
active radios or programs, where applicable (see Table 2-8).
To create a new item in the current program, tap New. To see the name of a button, hold the stylus
on the button. Drag the stylus off the button so the command is not carried out.
Tap to change volume or mute all sounds
Tap to close program
Tap to quickly select a program
recently used
Tap to select a program
Tap to see additional programs
Tap to customize the device
New button.
Menu names
Figure 2-9. Screen Navigation
Input Panel
button
Buttons
Page 95
Operating
Status Icons
You may see the status icons listed in Table 2-8 on the navigation bar located at the top of the screen.
Table 2-8. Status Icons
IconFunctionDescription
SpeakerTurns all sounds on and off.
BatteryBackup battery is very low.
Main battery is charging.*
Main battery is low.
Main battery is very low.
Main battery is full.*
ConnectivityConnection is active.
Synchronization is occurring.
2-35
X
WWAN (MC9062/MC9063
only)
Instant MessageNotification that one or more instant messages
E-MailNotification that one or more e-mail messages
* Only appears in the Time and Next Appointment dialog box.
No connection.
Missed call.
Call in progress.
Antenna/signal icon: wireless on/good signal.
Antenna/signal icon: wireless off.
Antenna/signal icon: no service or searching.
were received.
were received.
Page 96
2-36
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Table 2-8. Status Icons (Continued)
IconFunctionDescription
Time and Next
Appointment
Multiple NotificationsThere are more notification icons than can be
* Only appears in the Time and Next Appointment dialog box.
Displays current time in analog or digital format.
displayed. Tap to display remaining icons.
Task Tray Ico ns
You may see the task tray icons listed in Table 2-9 on the command bar located at the bottom of the
screen.
Table 2-9. Task Tray Icons
IconDescription
The Mobile Companion icon appears in the task tray and indicates mobile
computer signal strength. See Chapter 5, Spectrum24 Configuration for
more information.
The Bluetooth icon appears in the task tray and indicates that the Bluetooth
radio is on. The Bluetooth icon disappears when the radio is off. The
Bluetooth icon is for display purposes only. See Chapter 8, Bluetooth for
more information.
The ActiveSync icon appears in the task tray and indicates an active
connection between the mobile computer and the development PC. See
Using ActiveSync on page 4-21 for more information.
Speaker Icon
You can adjust the system volume and phone ringing volume (MC9062/MC9063 only) using the
Speaker icon in the Navigation bar.
Page 97
1.Tap the Speaker icon. The Volume dialog box appears.
Operating
2-37
Mobile Computers without Phone
Mobile Computers with Phone
Figure 2-10. Volume Dialog Box
2.Tap and move the slide bar under the mobile computer icon to adjust the system volume.
Tap and move the slide bar under the phone icon to adjust the phone ringing volume, where
applicable.
3.Select the On or Off radio button to turn the volume on or off.
The system volume can also be adjusted using the Sounds & Notifications
window. See Sounds & Notifications on page 3-23 for more information.
Page 98
2-38
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Battery Icon
Battery icons display on the Navigation Bar when the main battery or backup battery power falls
below a predetermined level. A Battery dialog box also appears indicating the status of the main or
backup battery.
Figure 2-11. Battery Status Dialog Box
The battery status can also be viewed using the Power window. See Power on page 3-44 for more
information.
When the main battery is very low in MC9062 and MC9063 mobile
computers, power to GSM and CDMA is shut down.
Page 99
Connectivity Icon
The Connectivity icon indicates the communication status of the mobile computer when it’s
connecting to the internet or host computer.
Figure 2-12. Connectivity Dialog Boxes
Phone Icon (MC9062/MC9063 Only)
The Phone icon indicates the mobile computer’s wireless phone status.
Operating
2-39
Figure 2-13. Phone Dialog Boxes
Page 100
2-40
MC9000-K/S with Windows® Mobile 2003 Software for Pocket PCs PRG
Antenna Icon (MC9062/MC9063 Only)
The Antenna icon indicates the mobile computer’s wireless signal status, radio mode and the
communication status of the mobile computer when it’s connecting to the internet (if applicable).
Figure 2-14. Antenna Dialog Boxes
When controlling the power state of the WWAN radio, it is recommended
that the Radio Power window be used (see Radio Power on page 3-48) and
NOT the flight mode settings shown in Figure 2-14.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.