Zebra MC75A integrator Guide

Download

MC75A ENTERPRISE DIGITAL ASSISTANT

INTEGRATOR GUIDE

MC75A

ENTERPRISE DIGITAL ASSISTANT

USER GUIDE

72E-133624-03

Rev. A

April 2015

ii MC75A Enterprise Digital Assistant Integrator Guide

No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.

The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Zebra grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Zebra. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Zebra. The user agrees to maintain Zebra’s copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof.

Zebra reserves the right to make changes to any software or product to improve reliability, function, or design.

Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise under any Zebra, intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Zebra products.

Revision History

Changes to the original guide are listed below:

Change Date Description

-01 Rev. A 03/12/10 Initial release.

-02 Rev. A 05/2011 Add MC75A HF RFID support.

-03 Rev. A 04/2015 Zebra rebranding.

iii

iv MC75A Enterprise Digital Assistant Integrator Guide

Revision History.............................................................................................................................. iii

About This Guide

Introduction ..................................................................................................................................... xiii

Documentation Set ................................................................................................................... xiii

Configurations................................................................................................................................. xiv

Software Versions..................................................................................................................... xiv

Chapter Descriptions ...................................................................................................................... xvi

Notational Conventions................................................................................................................... xvii

Related Documents and Software .................................................................................................. xvii

Service Information......................................................................................................................... xviii

Chapter 1: Getting Started

Introduction .................................................................................................................................... 1-1

Unpacking the MC75A ................................................................................................................... 1-1

Getting Started ............................................................................................................................... 1-1

Installing the Main Battery ........................................................................................................ 1-2

Charging the Battery ................................................................................................................ 1-3

Charging the Main Battery and Memory Backup Battery ................................................... 1-3

Charging Spare Batteries ................................................................................................... 1-4

Charging Temperature ....................................................................................................... 1-4

Powering On the MC75A ......................................................................................................... 1-4

Calibrating the Screen ............................................................................................................. 1-5

Checking Battery Status .......................................................................................................... 1-5

Resetting the MC75A ..................................................................................................................... 1-5

Performing a Warm Boot ......................................................................................................... 1-5

Performing a Cold Boot ............................................................................................................ 1-5

Performing a Clean Boot .......................................................................................................... 1-6

Waking the MC75A ........................................................................................................................ 1-6

Micro Secure Digital (microSD) Card ............................................................................................. 1-7

Replacing the Main Battery ............................................................................................................ 1-8

Installing SAM Cards in MC75A6 HF RFID ................................................................................... 1-10

Removal ................................................................................................................................... 1-11

viii MC75A Enterprise Digital Assistant Integrator Guide

Chapter 2: Accessories

Introduction .................................................................................................................................... 2-1

Single Slot USB/Serial Cradle ....................................................................................................... 2-4

Setup ........................................................................................................................................ 2-4

Charging the MC75A Battery ................................................................................................... 2-4

Charging the Spare Battery ..................................................................................................... 2-5

Battery Charging Indicators ..................................................................................................... 2-5

Charging Temperature ....................................................................................................... 2-6

Four Slot Ethernet Cradle .............................................................................................................. 2-7

Setup ........................................................................................................................................ 2-7

Daisychaining Ethernet Cradles ............................................................................................... 2-7

Bandwidth Considerations when Daisychaining ................................................................ 2-8

Ethernet Cradle Drivers ........................................................................................................... 2-8

Charging and Communication ................................................................................................. 2-10

LED Charging Indicators .......................................................................................................... 2-10

Charge LED ....................................................................................................................... 2-10

Speed LED ......................................................................................................................... 2-11

Link LED ............................................................................................................................ 2-11

Charging Temperature ....................................................................................................... 2-11

Four Slot Charge Only Cradle ....................................................................................................... 2-12

Setup ........................................................................................................................................ 2-12

Charging Temperature ....................................................................................................... 2-12

Wall Mount Bracket ........................................................................................................................ 2-13

VCD7X00 Vehicle Cradle .............................................................................................................. 2-15

Requirements ........................................................................................................................... 2-15

Connector Ports ....................................................................................................................... 2-15

Connector Pin-Outs ........................................................................................................... 2-16

Mounting the Cradle ................................................................................................................. 2-16

Power Connection .................................................................................................................... 2-17

Serial Device Connection ......................................................................................................... 2-19

Charging the MC75A Battery ................................................................................................... 2-19

Removing the MC75A ........................................................................................................ 2-20

Charging the Spare Battery ..................................................................................................... 2-20

Battery Charging Indicators ..................................................................................................... 2-21

Charging Temperature ....................................................................................................... 2-22

Four Slot Battery Charger .............................................................................................................. 2-23

Battery Shim Installation .......................................................................................................... 2-23

Spare Battery Charging ........................................................................................................... 2-23

Battery Charging Indicators ..................................................................................................... 2-24

Charging Temperature ....................................................................................................... 2-24

Cables ............................................................................................................................................ 2-25

Setup ........................................................................................................................................ 2-25

Battery Charging ...................................................................................................................... 2-26

LED Charge Indications ........................................................................................................... 2-26

Charging Temperature ....................................................................................................... 2-26

Communication Setup .............................................................................................................. 2-26

Chapter 3: ActiveSync

Introduction .................................................................................................................................... 3-1

Installing ActiveSync ...................................................................................................................... 3-1

Table of Contents ix

Mobile Computer Setup ................................................................................................................. 3-2

Setting Up an ActiveSync Connection on the Host Computer ....................................................... 3-2

Synchronization with a Windows Mobile 6 Device ................................................................... 3-3

Chapter 4: Application Deployment for Mobile 6

Introduction .................................................................................................................................... 4-1

Security .......................................................................................................................................... 4-1

Application Security ................................................................................................................. 4-1

Digital Signatures ..................................................................................................................... 4-1

Locking Down a Mobile Computer ..................................................................................... 4-2

Installing Certificates .......................................................................................................... 4-3

Device Management Security .................................................................................................. 4-3

Remote API Security ................................................................................................................ 4-3

Packaging ...................................................................................................................................... 4-4

Deployment .................................................................................................................................... 4-4

Installation Using ActiveSync ................................................................................................... 4-4

Installation Using Storage Card ............................................................................................... 4-4

Installation Using AirBEAM ...................................................................................................... 4-5

MSP 3.X ................................................................................................................................... 4-5

Image Update .......................................................................................................................... 4-5

Creating a Splash Screen ........................................................................................................ 4-6

XML Provisioning ........................................................................................................................... 4-6

Creating an XML Provisioning File ........................................................................................... 4-7

XML Provisioning vs. RegMerge and Copy File ...................................................................... 4-7

RegMerge .......................................................................................................................... 4-7

CopyFiles ........................................................................................................................... 4-8

Storage .......................................................................................................................................... 4-8

Random Access Memory ......................................................................................................... 4-9

Volatile File Storage (Cache Disk) ..................................................................................... 4-9

Persistent Storage ................................................................................................................... 4-9

Application Folder .................................................................................................................... 4-9

System Configuration Manager ..................................................................................................... 4-9

File Types ................................................................................................................................ 4-10

User Interface .......................................................................................................................... 4-10

Menu Functions .................................................................................................................. 4-10

Parameter State Indicators ................................................................................................ 4-11

Window Status Bar ............................................................................................................. 4-11

File Deployment ....................................................................................................................... 4-12

Enterprise Mobility Developer Kits ................................................................................................. 4-12

Chapter 5: MC75A6 - GSM Configuration

Introduction .................................................................................................................................... 5-1

Quick Startup Steps ....................................................................................................................... 5-1

MC75A6 Service Verification ......................................................................................................... 5-3

Ensuring Network Coverage .................................................................................................... 5-3

Configuring a Data Connection ................................................................................................ 5-4

Establishing a Data Connection ............................................................................................... 5-5

Ending a Data Connection ....................................................................................................... 5-7

MC75A6 Settings ........................................................................................................................... 5-8

x MC75A Enterprise Digital Assistant Integrator Guide

Phone ....................................................................................................................................... 5-8

Sounds ............................................................................................................................... 5-8

Security .............................................................................................................................. 5-9

Services ................................................................................................................................... 5-10

Call Barring (Call Blocking) ................................................................................................ 5-10

Caller ID ............................................................................................................................. 5-11

Call Forwarding .................................................................................................................. 5-11

Call Waiting ........................................................................................................................ 5-12

Voice Mail and Text Messages .......................................................................................... 5-12

Fixed Dialing ...................................................................................................................... 5-13

Network .................................................................................................................................... 5-13

Changing Networks Manually ............................................................................................ 5-14

Viewing Available Networks ............................................................................................... 5-14

Setting Preferred Networks ................................................................................................ 5-15

Phone Info ................................................................................................................................ 5-16

Network Time Synchronization ...................................................................................................... 5-17

Enhanced Operator Name String .................................................................................................. 5-17

Service Provider Name Display ..................................................................................................... 5-17

Chapter 6: MC75A8 - CDMA Configuration

Introduction .................................................................................................................................... 6-1

Quick Startup Steps ....................................................................................................................... 6-1

CDMA Phone Activation ................................................................................................................ 6-2

Verizon Wireless Activation ..................................................................................................... 6-2

Sprint Activation ....................................................................................................................... 6-3

Automatic Activation .......................................................................................................... 6-3

Manual Activation ............................................................................................................... 6-4

Activation Test ......................................................................................................................... 6-6

Establishing a Data Connection ..................................................................................................... 6-7

CDMA Settings .............................................................................................................................. 6-8

Phone ....................................................................................................................................... 6-8

Location Settings ..................................................................................................................... 6-9

Data Settings ........................................................................................................................... 6-9

Verizon Wireless Data Settings ......................................................................................... 6-9

System Settings ....................................................................................................................... 6-10

Verizon System .................................................................................................................. 6-10

Version Information .................................................................................................................. 6-11

Services ................................................................................................................................... 6-11

Call Barring (Call Blocking) ................................................................................................ 6-11

Caller ID ............................................................................................................................. 6-11

Call Forwarding .................................................................................................................. 6-12

Call Waiting ........................................................................................................................ 6-12

Voice Mail and Short Message Service (SMS) .................................................................. 6-12

Network Time Synchronization ...................................................................................................... 6-12

Chapter 7: Interactive Sensor Technology Configuration

Introduction .................................................................................................................................... 7-1

IST Menu ................................................................................................................................. 7-1

General Tab ............................................................................................................................. 7-2

Table of Contents xi

Power Management Tab .......................................................................................................... 7-3

Keep Alive On Motion ........................................................................................................ 7-3

On Face Down ................................................................................................................... 7-3

Wake Up on Motion ............................................................................................................ 7-3

Setting Sensitivity ............................................................................................................... 7-3

Display Tab .............................................................................................................................. 7-4

Event Log Tab .......................................................................................................................... 7-4

Motion Event Details .......................................................................................................... 7-5

Chapter 8: Wireless Applications

Introduction .................................................................................................................................... 8-1

Signal Strength Icon ....................................................................................................................... 8-2

Turning the WLAN Radio On and Off ............................................................................................ 8-4

Chapter 9: Maintenance and Troubleshooting

Introduction .................................................................................................................................... 9-1

Maintaining the MC75A .................................................................................................................. 9-1

Removing the Screen Protector ..................................................................................................... 9-2

Battery Safety Guidelines .............................................................................................................. 9-2

Cleaning ......................................................................................................................................... 9-3

Materials Required ................................................................................................................... 9-3

Cleaning the MC75A ................................................................................................................ 9-4

Housing .............................................................................................................................. 9-4

Display ............................................................................................................................... 9-4

Scanner Exit Window ......................................................................................................... 9-4

Connector ........................................................................................................................... 9-4

Cleaning Cradle Connectors .................................................................................................... 9-4

Cleaning Frequency ................................................................................................................. 9-5

Troubleshooting ............................................................................................................................. 9-6

MC75A ..................................................................................................................................... 9-6

Bluetooth Connection ............................................................................................................... 9-8

Single Slot USB/Serial Cradle .................................................................................................. 9-9

Four Slot Ethernet Cradle ........................................................................................................ 9-10

Vehicle Cradle .......................................................................................................................... 9-10

Four Slot Spare Battery Charger ............................................................................................. 9-11

Cables ...................................................................................................................................... 9-11

Magnetic Stripe Reader ........................................................................................................... 9-12

Appendix A: Technical Specifications

Technical Specifications ................................................................................................................ A-1

MC75A ........................................................................................................................................... A-1

MC75A COM Port Definitions .................................................................................................. A-5

MC75A Pin-Outs ...................................................................................................................... A-5

MC75A Accessory Specifications .................................................................................................. A-6

Single Slot USB/Serial Cradle .................................................................................................. A-6

Four Slot Ethernet Cradle ........................................................................................................ A-7

Four Slot Charge Only Cradle .................................................................................................. A-7

Four Slot Battery Charger ........................................................................................................ A-8

xii MC75A Enterprise Digital Assistant Integrator Guide

Magnetic Stripe Reader ........................................................................................................... A-8

Appendix B: Bluetooth Configuration

Glossary

Index

ABOUT THIS GUIDE

Introduction

This Integrator Guide provides information about using the MC75A Enterprise Digital Assistant (EDA) and accessories.

NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.

Documentation Set

The documentation set for the MC75A provides information for specific user needs, and includes:

•

MC75A Quick Start Guide - describes how to get the MC75A EDA up and running.

•

MC75A Enterprise Digital Assistant User Guide - describes how to use the MC75A EDA.

•

MC75A Enterprise Digital Assistant Integrator Guide - describes how to set up the MC75A EDA and

accessories.

•

Microsoft® Windows Mobile 6.0 Applications User Guide - describes how to use Microsoft developed

applications.

•

Application Guide - describes how to use Zebra developed sample applications.

•

Enterprise Mobility Developer Kit (EMDK) Help File - provides API information for writing applications.

xiv MC75A Enterprise Digital Assistant Integrator Guide

Configurations

This guide covers the following configurations:

Configuration Radios Display Memory

MC75A0 WPAN: Bluetooth

WLAN: 802.11a/b/g

MC75A6 WPAN: Bluetooth

WLAN: 802.11a/b/g WWAN: HSDPA GPS: SiRF III

MC75A8 WPAN: Bluetooth

WLAN: 802.11a/b/g WWAN: EVDO GPS: SiRF III

MC75A6 HF RFID

WPAN: Bluetooth WLAN: 802.11a/b/g WWAN: HSDPA GPS: SiRF III

3.5” VGA Color

256 MB RAM/ 1 GB Flash

Data

Capture

1D laser scanner, 2D imager or camera

Operating

System

Windows Mobile 6.5 Classic

Windows Mobile 6.5 Professional

Keypads

Numeric or QWERTY keypads

Numeric, DSD, QWERTY, AZERTY or QWERTZ keypads

Numeric or QWERTY keypads

Software Versions

This guide covers various software configurations and references are made to operating system or software versions for:

•

Adaptation Kit Update (AKU) version

•

OEM version

•

BTExplorer version

•

Fusion version

AKU Version

To determine the Adaptation Kit Update (AKU) version:

Ta p

Start > Settings > System folder > About icon > Version tab.

About This Guide xv

The second line lists the operating system version and the build number. The last part of the build number represents the AKU number. For example, Build 18552.0.7.5 indicates that the device is running AKU version

0.7.5.

OEM Version

To determine the OEM software version:

Ta p

Start > Settings > System folder > System Info icon > System tab.

MC75A

BTExplorer Software

NOTE To view the BTExplorer version information, the StoneStreet One Bluetooth stack must be enabled. Refer to

the MC75A Enterprise Digital Assistant Integrator Guide for more information.

To determine the BTExplorer software version:

Ta p Start >

BTExplorer icon > Show BTExplorer> Menu > About.

xvi MC75A Enterprise Digital Assistant Integrator Guide

Fusion Software

To determine the Fusion software version:

Ta p Start > Wireless Companion icon > Wireless Status icon >

Chapter Descriptions

Topics covered in this guide are as follows:

•

Chapter 1, Getting Started provides information on MC75A configurations and accessories, charging the

ery, and resetting.

batt

Versions.

•

Chapter 2, Accessories describes the accessories available for the MC75A and how to set up power

connections

•

Chapter 3, ActiveSync provides instructions on installing ActiveSync and setting up a partnership

tween the MC75 and a host computer.

•

Chapter 4, Application Deployment for Mobile 6 provides information for provisioning and deploying

applications to the MC75A.

•

Chapter 5, MC75A6 - GSM Configuration explains how to verify MC75A6 service on an Enhanced Data

rates for Global Evolution (EDGE) wireless network and establish settings.

•

Chapter 6, MC75A8 - CDMA Configuration explains how to configure MC75A8 service on an CDMA

wire

less network and establish settings.

and battery charging capabilities, where applicable.

•

Chapter 7, Interactive Sensor Technology Configuration describes how to configure interactive sensing

technology of the MC75A.

•

Chapter 8, Wireless Applications describes how to configure the wireless LAN connection.

•

Chapter 9, Maintenance and Troubleshooting includes instructions on cleaning and storing the MC75A,

nd provides troubleshooting solutions for potential problems during MC75A operation.

•

Appendix A, Technical Specifications includes tables listing the technical specifications for the MC75A

nd its accessories.

•

Appendix B, Bluetooth Configuration provides registry settings for configuring Bluetooth software.

Notational Conventions

The following conventions are used in this document:

•

“MC75A” refers to all configurations of the MC75AX mobile computer.

•

Italics are used to highlight the following:

• chapters and sections in this and related documents

• dialog box, window, and screen names

• drop-down list and list box names

• check box and radio button names

• icons on a screen.

About This Guide xvii

•

Bold text is used to highlight the following:

• key names on a keypad

• button names on a screen.

•

Bullets (•) indicate:

• action items

• lists of alternatives

• lists of required steps that are not necessarily sequential.

•

Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.

Service Information

If you have a problem with your equipment, contact Zebra support for your region. Contact information is available at: http://www.zebra.com/support

When contacting Zebra support, please have the following information available:

•

Serial number of the unit

•

Model number or product name

•

Software type and version number

Zebra responds to calls by email, telephone or fax within the time limits set forth in support agreements.

If your problem cannot be solved by Zebra Support, you may need to return your equipment for servicing and will be given specific directions. Zebra is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.

If you purchased your business product from a Zebra business partner, contact that business partner for support.

CHAPTER 1 GETTING STARTED

Introduction

This chapter provides information about the MC75A, accessories, charging the MC75A, and resetting the MC75A.

Unpacking the MC75A

Carefully remove all protective material from the MC75A and save the shipping container for later storage and shipping. Verify that you received the following equipment:

•

MC75A

•

Lithium-ion battery

•

Battery cover/strap assembly

•

Tethered stylus

•

Regulatory Guide

•

Quick Start Guide.

Inspect the equipment. If any equipment is missing or damaged, contact the Zebra support immediately. See

Service Information on page xviii for contact information.

Getting Started

To start using the MC75A for the first time:

•

Install the main battery.

•

Charge the MC75A.

•

Power on the MC75A.

•

Configure the MC75A.

1 - 2 MC75A Enterprise Digital Assistant Integrator Guide

Battery

Release Latch

Battery Cover

Battery Cover Latch

Handstrap Slot

Handstrap

Charge the main battery before or after it is installed. Use one of the spare battery chargers to charge the battery (out of the MC75A), or one of the cradles to charge the battery installed in the MC75A.

Installing the Main Battery

NOTE The MC75A ships with either a 1950 mAh or a 3600 mAh battery. An optional 4800 mAh battery is

available.

To install the main battery.

1. Insert the battery, top first, into the battery compartment in the back of the MC75A.

NOTE Position the battery correctly, with the battery charging contacts on top of the charging contacts in the

battery compartment.

2. Press the battery down into the battery compartment until the battery release latch snaps into place.

Figure 1-1

3. With the battery cover latches open, insert the cover, bottom first, then press down on the top of the cover.

4. Close the battery cover latches on either side of the battery cover.

5. Insert the handstrap through the handstrap slot, then tighten and press down to secure.

Figure 1-2

Inserting the Battery

Inserting the Handstrap

The MC75A powers up after inserting the battery and replacing the battery cover.

Getting Started 1 - 3

Charging the Battery

CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page

9-2.

Charging the Main Battery and Memory Backup Battery

Before using the MC75A for the first time, charge the main battery until the amber Charging/Battery Status LED remains lit (see Table 1-2 on page 1-4 for charge status indications). To charge the MC75A, use a cable or a cradle with the appropriate power supply. For information about the accessories available for the MC75A, see

Chapter 2, Accessories.

The MC75A is equipped with a memory backup battery which automatically charges from the fully-charged main battery. When using the MC75A for the first time, the backup battery requires approximately 36 hours to fully charge. This is also true any time the backup battery is discharged, which occurs when the main battery is removed for several hours. The backup battery retains RAM data in memory for at least 15 minutes (at room temperature) when the MC75A's main battery is removed. When the MC75A reaches a very low battery state, the combination of main battery and backup battery retains RAM data in memory for at least 48 hours.

To charge the main battery, use either a charging cable or a cradle. For cable and cradle setup and charging procedures see Chapter 2, Accessories.

•

Single Slot USB/Serial Cradle

•

Four Slot Ethernet Cradle

•

Four Slot Charge Only Cradle

•

Vehicle Cradle.

To charge the main battery:

1. Connect the charging accessory to the appropriate power source.

2. Insert the MC75A into a cradle or attach to a cable. The MC75A begins charging. The Charging/Battery

Status LED blinks amber while charging, then turns solid amber when fully charged. See Table 1-2 for

charging indications.

Table 1-1 lists the charge times for each available battery:

Table 1-1

1950 mAh Changes in less than four hours.

3600 mAh Changes in less than eight hours.

4800 mAh Changes in less than ten hours.

Battery Charge Times

Battery Size Charge Time

1 - 4 MC75A Enterprise Digital Assistant Integrator Guide

Radio Status LED

(MC75A6/8 only)

Scan/Decode

LED

Charging/Battery

Status LED

Figure 1-3

Table 1-2

Off MC75A is not charging.

Slow Blinking Amber (1 blink every 2 seconds)

Solid Amber Charging complete.

Fast Blinking Amber (2 blinks/second)

LED Indicators

LED Charge Indicators

Charging/Battery

Status LED

Indication

MC75A is not inserted correctly in the cradle or connected to a power source. Charger/cradle is not powered.

MC75A is charging.

Note: When the battery is initially inserted in the MC75A, the amber LED flashes once if the battery power is low or the battery is not fully inserted.

Charging error, e.g.:

•

Temperature is too low or too high.

•

Charging has gone on too long without completion (typically eight hours).

Charging Spare Batteries

See Chapter 2, Accessories for information on using accessories to change spare batteries.

Charging Temperature

Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Note that at temperatures above 35°C (95°F), charging is intelligently controlled by the MC75A and the charging accessory in order to ensure safe operation and optimize long-term battery life.

To accomplish this, for small periods of time, the MC75A or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. The MC75A or accessory indicates when charging is disabled due to abnormal temperatures via its LED. See Table 1-2.

Powering On the MC75A

Press the Power button to turn on the MC75A. If the MC75A does not power on, perform a warm boot. See

Resetting the MC75A on page 1-5.

Getting Started 1 - 5

When turning the MC75A on for the first time, the splash screen displays for about five minutes as the MC75A initializes its flash file system, then the calibration window appears. Note that these windows also appear upon cold boot.

NOTE When the MC75A powers up after inserting a battery for the first time, the device boots and powers on

automatically.

Calibrating the Screen

NOTE The Calibration screen can be accessed by pressing Blue key - BKSP key or tapping Start > Settings >

Screen > Align Screen button.

To calibrate the screen so the cursor on the touch screen aligns with the tip of the stylus:

1. Remove the stylus from its holder on the back of the MC75A.

2. Tap the screen to begin.

3. Carefully press and briefly hold the tip of stylus on the center of each target that appears on the screen.

4. Repeat as the target moves around the screen.

Checking Battery Status

To check the charge status of the main battery or backup battery in the MC75A, tap Start > Settings > Power icon to display the

To save battery power, tap the

Power window.

Resetting the MC75A

There are three reset functions, warm boot, cold boot and clean boot. A warm boot restarts the MC75A by closing all running programs. A cold boot also restarts the MC75A, and also initializes some drivers. Data saved in flash memory or a memory card is not lost. A clean boot resets the MC75A to factory defaults.

Perform a warm boot first. If the MC75A still does not respond, perform a cold boot.

Performing a Warm Boot

Hold down the Power button for approximately five seconds. As soon as the MC75A starts to perform a warm boot release the

Performing a Cold Boot

To perform a cold boot:

Power button.

Advanced tab and set the MC75A to turn off after a specified number of minutes.

1. Simultaneously press the Power button and the 1 and 9 keys.

2. The MC75A initializes.

1 - 6 MC75A Enterprise Digital Assistant Integrator Guide

Performing a Clean Boot

CAUTION A clean boot should only be performed by an authorized system administrator. You must connect the

MC75A to AC power during a clean boot.

Removing AC power from the MC75A during a clean boot may render the MC75A inoperable.

A clean boot resets the MC75A to the factory default settings. All data in the Application folder is retained. You must download the Clean Boot Package file from the Support Central web site (http://www.zebra.com/support and install on the MC75A.

To perform a clean boot:

1. Download the Clean Boot Package from the Support Central web site (http://www.zebra.com/support).

Follow the instructions included in the package for installing the package onto the MC75A.

2. Simultaneously press the Power button and the 1 and 9 keys.

3. Immediately, as soon as the device starts to boot and before the splash screen is visible, press and hold

the right scan button.

4. Insert the MC75A into a powered cradle.

)

5. The MC75A updates and then re-boots.

6. Calibrate the screen.

Waking the MC75A

The wake-up conditions define what actions wake up the mobile computer after it has gone into suspend mode. The mobile computer can go into suspend mode by either pressing the Power button or automatically by Control Panel time-out settings. To set the wake up conditions tap Start > Setting > Power icon > Wakeup tab.

Figure 1-4

Power Wakeup Tab

Getting Started 1 - 7

These settings are configurable and the factory default settings are shown in Table 1-3 are subject to change/update.

Table 1-3

AC power is applied to the MC75A. No Yes

The MC75A is inserted into a cradle. No Yes

The MC75A is removed from a cradle. No Yes

The MC75A is connected to a USB cable. Yes Yes

Mobile computer is disconnected from a USB device. No Yes

Mobile computer is connected from a USB Host device. No No

A key is pressed. No Yes

The scan button is pressed. No Yes

The screen is touched. No No

Audio Jack No No

Audio Btn Yes No

A Bluetooth device tries to communicate with the MC75A.

Wake-up Default Settings

Condition for Wake-up Power Button Automatic Time-out

Yes Ye s

On Motion No Yes

The MC75A is connected to a serial accessory. No Yes

Incoming phone call Yes Yes

Micro Secure Digital (microSD) Card

The microSD card slot provides secondary non-volatile storage. The slot is located on the side of the MC75A (see Figure 1-5). Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.

CAUTION Follow proper ESD precautions to avoid damaging the SD card. Proper ESD precautions include, but

are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.

To install the microSD card:

1. Remove the memory card cover on the side of the MC75A by loosening the two captive screws.

1 - 8 MC75A Enterprise Digital Assistant Integrator Guide

Figure 1-5

2. Insert the card with the card contacts facing up, until you feel a click.

3. Replace the memory card cover and tighten the screws.

Card Installation

To remove an microSD card:

1. Remove the memory card cover by loosening the screws.

Figure 1-6

2. Carefully press and release the card to eject it.

3. Remove the card from the card slot.

4. Replace the memory card cover and tighten the screws.

Card Removal

Replacing the Main Battery

5. If the MC75A is in suspend mode, press the red Power button to wake the device.

6. Press the red Power button to suspend the MC75A.

7. Wait for red Decode LED to turn on and then turn off.

8. Open the battery cover latches on either side of the battery cover.

Getting Started 1 - 9

Battery Cover Latch

Figure 1-7

9. Lift the top of the battery cover and remove.

10. Press the battery release latch on the bottom of the battery to unlock, and lift the battery out of the well.

11. Insert the replacement battery, top first, into the battery compartment in the back of the MC75A.

12. Press the battery down into the battery compartment until the battery release latch snaps into place.

13. With the battery cover latches open, insert the cover, bottom first, then press down on the top of the cover.

14. Close the battery cover latches on either side of the battery cover.

15. Press the red Power button to power on the MC75A.

Removing the Battery Cover

NOTE Position the battery correctly, with the battery charging contacts on top of the charging contacts in the

battery compartment.

1 - 10 MC75A Enterprise Digital Assistant Integrator Guide

Installing SAM Cards in MC75A6 HF RFID

The MC75A6 HF RFID uses Security Authentication Module (SAM) cards to store encryption keys. To install SAM cards:

1. Press the red Power button to suspend the MC75A.

2. Using a torx (T5) screwdriver, remove four screws securing the plate to the back housing.

Figure 1-8

3. Lift plate off the back housing.

4. Remove the plug covering the SAM slots.

Figure 1-9

5. Insert a SAM card into one of the slots with the contacts facing down (front of the device).

Remove Plate

Remove Plug

Getting Started 1 - 11

Figure 1-10

6. Replace the plug.

7. Align the plate onto the back housing.

Figure 1-11

8. Secure the plate to the back housing using the four torx (T5) screws.

9. Perform a warm boot.

Insert SAM Card

Replace Plate

Removal

1. Press the red Power button to suspend the MC75A.

2. Using a torx (T5) screwdriver, remove four screws securing the plate to the back housing.

3. Lift plate off the back housing.

4. Remove the plug covering the SAM slots.

5. Press the SAM card in until it ejects.

6. Remove the SAM card.

1 - 12 MC75A Enterprise Digital Assistant Integrator Guide

Figure 1-12

7. Replace the plug.

8. Align the plate onto the back housing.

9. Secure the plate to the back housing using the four torx (T5) screws.

10. Perform a warm boot.

Remove SAM Card

CHAPTER 2 ACCESSORIES

Introduction

This chapter provides set up information for various accessories of the MC75A. Table 2-1 lists all accessories available for the MC75A.

Table 2-1

Cradles

Single Slot USB/Serial Cradle

Four Slot Ethernet Cradle CRD7000-4000ER Charges the MC75A main battery and connects the MC75A

Four Slot Charge Only Cradle

VCD7000 Vehicle Cradle VCD7X00-P000R Installs in a vehicle and charges the MC75A main battery

Chargers

Four Slot Spare Battery Charger

Serial Charging Cable 25-102776-01R Provides power to the MC75A and serial communication

MC75A Accessories

Accessory Part Number Description

CRD7X00-1000RR Charges the MC75A main battery and a spare battery.

Synchronizes the MC75A with a host computer through either a serial or a USB connection.

with an Ethernet network.

CRD7X00-4000CR Charges up to four MC75A devices.

and a spare battery. Provides serial data communication between an MC75A and an external device.

SAC7X00-4000CR Charges up to four MC75A spare batteries. Includes an

MC75A shim.

with a host computer.

USB Charging Cable 25-102775-01R Provides power to the MC75A and USB communication with

a host computer.

Charge Only Cable 25-95214-02R Provides power to the MC75A.

Auto Charge Cable 25-70979-02R Charges the MC75A using a vehicle’s cigarette lighter.

2 - 2 MC75A Enterprise Digital Assistant Integrator Guide

Table 2-1

MC75A Accessories (Continued)

Accessory Part Number Description

Cables

DEX Cable 25-76793-01R Connects the MC75A to a vending machine.

Modem Dongle MDM9000-100R Provides modem connectivity to the MC75A.

Modem Inverter Cables 25-70924-03R Connects the MC75A to the modem dongle.

O’Neil Printer Cable 25-91519-01R Printer cable for O’Neil printers.

Zebra Printer Cable 25-91518-01R Printer cable Zebra Road Warrior printers.

Zebra Printer Cable 25-91515-01R Printer cable for Zebra QL printers.

Miscellaneous

Magnetic Stripe Reader (MSR)

MSR7000-100R Snaps on to the MC75A and adds magstripe read

capabilities.

Debit Card Reader DCR7X00-100R Allows easy data capture with the swipe of a magnetic stripe

card and personal identification number (PIN) entry using a numeric keypad.

Snap-on Mobile Payment Module with Chip and PIN

DCR7X00-200R Allows easy data capture with magnetic stripe cards, EMV

compliant Chip and PIN cards and personal identification number (PIN) entry using a numeric keypad.

Biometric Reader MC7XFPR-01R Contains a finger print reader.

Biometric Reader MC7XFPSCR-01R Contains a finger print reader, a contact smart card reader

and a contactless smart card reader.

Spare 3600 mAh

BTRY-MC7XEAB00 Replacement 3600 mAh battery.

lithium-ion battery

Spare 4800 mAh

BTRY-MC7XEAB0HOptional 4800 mAh battery.

lithium-ion battery

Battery Kit for 3600 mAh battery

Battery Kit for 4800 mAh battery

BTRY-KT-1R5XMC7XR

BTRY-KT-2R5XMC7XR

Replacement 3600 mAh battery and battery door.

Replacement 4800 mAh battery and battery door.

Headset 50-11300-050R Use in noisy environments.

Belt Mounted Rigid Holster

Fabric Holster SG-MC75AX21215

SG-MC7001111001R

Clips onto belt to hold the MC75A when not in use.

Soft holder for added protection.

-01R

Stylus Stylus-00002-03R Replacement stylus (3-pack).

Accessories 2 - 3

Table 2-1

Wall Mounting Kit 8710-050006-01R Use for wall mounting the four slot cradles.

Screen Protector KT-129195-03R Package of 3 screen protectors.

Software - Enterprise Mobility Developer Kits (EMDKs), available at:

MC75A Accessories (Continued)

Accessory Part Number Description

http://www.zebra.com/support

2 - 4 MC75A Enterprise Digital Assistant Integrator Guide

USB Port Power Port

Power Supply

Single Slot USB/Serial Cradle

This section describes how to set up and use a Single Slot USB/Serial cradle with the MC75A. For USB communication setup procedures see Chapter 3, ActiveSync.

The Single Slot USB/Serial Cradle:

•

Provides 5.4 VDC power for operating the MC75A.

•

Synchronizes information between the MC75A and a host computer. See Chapter 3, ActiveSync for information on setting up a partnership between the MC75A and a host computer.

•

Charges the MC75A’s battery.

•

Charges a spare battery.

Setup

Figure 2-1

Charging the MC75A Battery

Connect the cradle to power. Insert the MC75A into the MC75A slot to begin charging.

Single Slot USB/Serial Cradle Power and USB Connections

Accessories 2 - 5

Charging/Battery Status LED

Spare Battery Spare Battery

Charging LED

Figure 2-2

MC75A Battery Charging

Charging the Spare Battery

Figure 2-3

Spare Battery Charging

Battery Charging Indicators

The Single Slot USB/Serial Cradle charges the MC75A’s main battery and a spare battery simultaneously.

The MC75A’s Charge LED indicates the status of the battery charging in the MC75A. See Table 1-2 on page

1-4 for charging status indications.

The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle. See Table 2-2 for charging status indications.

The 3600 mAh battery fully charges in approximately five hours and the 4800 mAh battery fully charges in approximately seven hours.

2 - 6 MC75A Enterprise Digital Assistant Integrator Guide

Charging Temperature

Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75A.

Table 2-2

Slow Blinking Amber Spare battery is charging.

Solid Amber Spare battery is fully charged.

Fast Blinking Amber Charging error.

Off Not charging.

Spare Battery LED Charging Indicators

Spare Battery LED

(on cradle)

Indication

Four Slot Ethernet Cradle

Power Port

Ethernet Port

Ethernet Switch, Router, or Hub Connection

Ethernet Port 1

This section describes how to set up and use a Four Slot Ethernet cradle with the MC75A.

The Four Slot Ethernet cradle:

•

Provides 5.4 VDC power for operating the MC75A.

•

Connects the MC75A (up to four) to an Ethernet network.

•

Simultaneously charges up to four MC75As.

You cannot ActiveSync using the Four Slot Ethernet cradle. To ActiveSync with a host computer, use the SIngle Slot USB/Serial cradle, USB Charging cable or Serial Charging cable.

Setup

Connect the Ethernet cradle to a power source and to an Ethernet switch, router, or hub, or a port on the host device.

Accessories 2 - 7

Figure 2-4

Daisychaining Ethernet Cradles

Daisychain up to seven Ethernet cradles to connect several cradles to an Ethernet network. Use either a straight or crossover cable. Daisychaining more than four Ethernet cradles can lead to reduction in bandwidth.

To daisychain more than one Ethernet cradle:

1. Connect power to each Ethernet cradle to daisychain.

2. Connect an Ethernet cable to Port 1 of the first cradle as shown in Figure 2-4.

3. Connect a second Ethernet cable between Port 2 of the first cradle, and Port 1 of the second cradle.

4. Connect additional cradles as described in Step 3.

Four Slot Ethernet Cradle Connection

2 - 8 MC75A Enterprise Digital Assistant Integrator Guide

Ethernet Port 1

Ethernet Port 2

Link LED

Speed LED

Figure 2-5

Daisychaining Four Slot Ethernet Cradles

Bandwidth Considerations when Daisychaining

Each cradle added to the daisychain impacts the bandwidth provided to the inserted MC75As, particularly when the MC75As attempt to send and receive at data rates that exceed the bandwidth provided to the chain (typically 100 Mbps). If an MC75A in a daisychained cradle does not use its bandwidth, that bandwidth is allocated to other inserted MC75As.

Table 2-3 shows available bandwidth, based on 100 Mpbs, for the maximum number of daisychained cradles,

with each attempting transmission at the maximum data rate.

Table 2-3

Cradle 1 100,000,000 20,000,000

Cradle 2 20,000,000 4,000,000

Cradle 3 4,000,000 800,000

Cradle 4 800,000 160,000

Cradle 5 160,000 32,000

Cradle 6 32,000 6,400

Daisychaining Bandwidth

Daisychained Cradles

Bandwidth Allocation For Each

Ethernet Cradle (bits/sec)

Bandwidth Allocation For Each

Mobile Computer (bits/sec)

Cradle 7 6,400 1,280

* The maximum bandwidth capacity for the mobile computer is 12,000,000 bits/sec.

** Depending on the application, allocated bandwidth may not be adequate.

Note: 100 Mbps is the theoretical maximum. This rate is never actually achieved in any Ethernet

installation.

Ethernet Cradle Drivers

The MC75A includes Ethernet cradle drivers that initiate automatically when you place the MC75A in a properly connected Four Slot Ethernet cradle. After inserting the MC75A, configure the Ethernet connection:

1. Ta p Start > Settings > Connections tab >WiFi icon. The Configure Network Adapters window appears.

Accessories 2 - 9

JEDIWiFiDriver

Figure 2-6

2. In the My network card connects to: drop-down list, select the appropriate connection.

3. In the Tap an adapter to modify settings: list, select USB/Ethernet Series Adapter.

Figure 2-7

4. In the IP address window, select the appropriate radio button:

•

Configure Network Adapters Window

IP Address Tab

Use server-assigned IP address

•

Use specific IP address. Enter the IP address, Subnet mask, and Default gateway, as needed.

5. Tap the Name Servers tab.

2 - 10 MC75A Enterprise Digital Assistant Integrator Guide

Link LED

Speed LED

Figure 2-8

6. Enter the appropriate DNS, Alt DNS, WINS, and Alt WINS server addresses.

7. Ta p ok.

8. Ta p ok to exit.

Name Servers Tab

Charging and Communication

Insert the MC75A into a slot to begin charging.

Figure 2-9

MC75A Battery Charging

LED Charging Indicators

Charge LED

The MC75A’s charge LED shows the status of the battery charging in the MC75A. See Table 1-2 on page 1-4 for charging status indications.

The 3600 mAh battery fully charges in approximately five hours and the 4800 mAh battery fully charges in approximately seven hours.

Accessories 2 - 11

Speed LED

The cradle’s green Speed LED lights to indicate that the transfer rate is 100 Mbps. When it is not lit it indicates that the transfer rate is 10Mbps.

Link LED

The cradle’s yellow Link LED blinks to indicate activity, or stays lit to indicate that a link is established. When it is not lit it indicates there is no link.

Charging Temperature

Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75A.

2 - 12 MC75A Enterprise Digital Assistant Integrator Guide

Four Slot Charge Only Cradle

This section describes how to set up a Four Slot Charge Only cradle with the MC75A.

The Four Slot Charge only cradle:

•

Provides 5.4 VDC power for operating the MC75A.

•

Simultaneously charges up to four MC75As.

NOTE You cannot ActiveSync using the Four Slot Charge Only cradle. To ActiveSync with a host computer, use

the Single Slot USB/Serial cradle, USB Charging cable or Serial Charging cable.

Setup

Connect the Four Slot Charge Only cradle to a power source.

Figure 2-10

Four Slot Charge Only Cradle Power Connection

Charging Temperature

Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75A.

Wall Mount Bracket

Mounting Screw (4)

Mounting Tab (2)

Mounting Slot

Mounting Screw (2)

Four Slot

Cradle Bottom

Use the optional Wall Mount Bracket to mount a four slot cradle to a wall. To attach the Wall Mount Bracket:

1. Use the Wall Mount Bracket as a template and mark the locations of the four mounting screws.

NOTE Use fasteners appropriate for the type of wall and the Wall Mount Bracket mounting slots. The Wall Mount

Bracket mounting slots are designed for a fastener with a #8 pan head.

2. Mount the fasteners to the wall. The screw heads should protrude about a half of an inch from the wall.

3. Slip the Wall Mount Bracket over the screw heads and slide the bracket down over the screw heads.

4. Tighten the screws to secure the bracket to the wall.

Accessories 2 - 13

Figure 2-11

Wall Mount Bracket

To mount a four slot cradle:

1. Screw the supplied fasteners into the bottom of the four slot cradle. The screw heads should protrude

about a quarter of an inch from the cradle.

Figure 2-12

2. Align the Wall Mount Bracket mounting tabs with the mounting slots in the back of the four slot cradle. Slip

Cradle Mounting Screws

the two mounting tabs into mounting slots.

3. Swing the four slot cradle down onto the mounting bracket and align the mounting screws so that they fit

into the screw slots.

2 - 14 MC75A Enterprise Digital Assistant Integrator Guide

Wall Mount

Bracket

Screw Slots

Power Supply

Well

Figure 2-13

4. Tighten the mounting screws to secure the four slot cradle to the bracket.

Figure 2-14

5. Connect power (see Figure 2-4 on page 2-7). The power supply should be located in the power supply

Wall Mount Bracket

Mounting Screws

well.

VCD7X00 Vehicle Cradle

This section describes how to set up a VCD7X00 vehicle cradle.

Once installed in a vehicle, the cradle:

•

holds the MC75A securely in place

•

provides power for operating the MC75A

•

provides a serial port for data communication between an MC75A and an external device (e.g., a printer)

•

re-charges the battery in the MC75A

•

re-charges a 3600 mAh or 4800 mAh battery.

Requirements

For mounting:

•

four #8-32 self-locking nuts

•

four #8 washers

Accessories 2 - 15

•

a drill with a #6 drill bit (.204”).

For power connection:

•

power input cable (included), p/n 25-61987-01R

•

UL Listed in-line fuse rated 250V, 5A (included), must be used if not connecting to vehicle’s fuse panel

•

in-line fuse holder (included), must be used if not connecting to vehicle’s fuse panel.

For serial connection:

•

DB9 female serial cable (some devices may require null modem).

For communication:

•

an MC75A

•

host computer setup and MC75A setup (as determined by the application you are using).

Connector Ports

There are two connection ports on the bottom of the vehicle cradle:

Table 2-4

Vehicle Cradle Connection Ports

Ports Function

Serial Standard RS 232 port used for direct connection to the serial device using a serial cable.

Power Used for connecting to vehicle power using the power input cable.

2 - 16 MC75A Enterprise Digital Assistant Integrator Guide

Connector on Power Cable

Connector on Serial Cable

Connector Pin-Outs

Table 2-5

Power Input Cable

Pin Signal

1 Chassis ground (Black Wire)

2 Chassis ground (Bare Wire)

3 V+ (Red Wire)

4 V+ (Red Wire)

Table 2-6

Serial Cable

Pin Signal Pin Signal

1DCD5GND

2RxD6DSR

3TxD7RTS

4DTR8CTS

5GND95V_OUT

CAUTION ROAD SAFETY - Do not use the MC75A while driving. Park the vehicle first. Always ensure the

MC75A is fully inserted into the cradle. Do not place it on the seat or where it can break loose in a collision or sudden stop. Lack of proper insertion may result in property damage or personal injury. Zebra is not responsible for any loss resulting from the use of the products while driving. Remember: Safety comes first.

Mounting the Cradle

CAUTION Only mount the Vehicle Cradle in a vertical position with the release level at the top or in a horizontal

position with the MC75A display facing up. Never mount the vehicle cradle on the side or upside down or on a wall that can be subject to impact or collision of greater than 40Gs, in accordance with SAE J1455 Section 4.10.3.5

1. Select a mounting location for the cradle. It should be flat, and must provide adequate support for the

cradle.

NOTE If using the GPS functionality of the MC75A mobile computer, ensure that the vehicle cradle is positioned

so that the MC75A has a clear unobstructed view of the sky.

2. Prepare the mounting surface to accept four #8-32 studs, using the mounting template below. Drill four

holes with a #6 drill bit.

Accessories 2 - 17

1.5”

3.81 cm

1.2”

3.05 cm

Figure 2-15

3. Position the cradle on the mounting surface.

4. Fasten it using four #8 washers and four #8-32 self-locking nuts.

CAUTION Do not install a VCD7000 Vehicle Cradle on or near an air bag cover plate or within an aerobic zone.

Power Connection

Please read all of the following instructions before beginning.

WARNING! A properly trained technician must perform the power connection. Improper connection can

To connect the cradle to power:

CAUTION When setting up connection for this cradle, only use the power input cable provided with this cradle.

1. Locate the vehicle power source.

NOTE The ideal location for connecting the vehicle cradle power input cable would be an accessory output in

Vehicle Cradle Mounting Template

Also, do not install it in a location that affects vehicle safety or driveability.

damage your vehicle, cradle or MC75A. Refer to the vehicle’s Owner’s Manual for instructions for removing power.

your vehicle’s fuse panel. The vehicle cradle should be added to a circuit with a maximum load capacity for the cradle and the original circuit. Refer to the vehicle’s Owner’s Manual for identification of the circuit. If a fused output is not available, the vehicle cradle must be installed with the provided in-line fuse holder and UL Listed 5A fuse. The fuse protects the vehicle from an electrical short on the power line to the cradle. To use the cradle to charge the MC75A and spare battery when the vehicle’s ignition is off, connect the cradle to unswitched power. This will affect the vehicle’s battery charge.

2 - 18 MC75A Enterprise Digital Assistant Integrator Guide

Shield Wire

(bare wire)

Ground

Wire (black)

V+ Power (red)

5A Fuse and

Fuse Holder

2. Route the power input cable from the cradle’s power port to the connection point for the vehicle’s power

source.

CAUTION The means of routing and securing the power input cable from the cradle through to the vehicle power

source is extremely important. Hazards associated with improper wiring can be severe. To avoid unintentional contact between the wire and any sharp edges, provide the cable with proper bushings and clamping where it passes through openings. If the wire is subjected to sharp surfaces and excess engine vibration, the wiring harness insulation can wear away, causing a short between the bare wire and chassis. This can start a fire. To avoid any mishaps, all wiring should be routed away from moving parts, high temperature areas and any contaminants.

3. When using the supplied in-line fuse holder (which must be used if not connecting to vehicle’s fuse panel):

a. Ensure the fuse holder contains a 5A UL Listed slow-blow fuse.

b. Splice the fuse holder to the end of the red V+ wire, as shown above. Make the distance from the fuse

to the power connection point as short as possible.

Figure 2-16

4. Prepare the cable termination.

a. Red wire: connect to a +12/24 V vehicle power source.

b. Black wire and Shield wire: connect to vehicle ground wire or chassis ground.

5. Connect the power input cable into the power port on the cradle.

Vehicle Cradle Power Connection

NOTE How the cable terminates depends on the vehicle. If the vehicle has a power output connector, then you must

attach a mating connector to the end of the power cable. You may be able to connect to a fuse panel with a simple blade terminal or commercially available connector. Consult the vehicle Owner’s Manual for information on how to access the power supply in the vehicle.

To see if the cradle has power, insert the MC75A. The Charging LED on the MC75A blinks slowly to indicate charging and turns solid amber when the battery is completely charged. See Table 1-2 on page 1-4 for other indications.

Accessories 2 - 19

To Serial Port of

Serial Device

Serial Device Connection

The MC75A has a serial port on the bottom. When the MC75A is inserted into the cradle, it connects to the cradle’s serial port. The MC75A can then use the cradle’s serial port to communicate with an external device.

Figure 2-17

Vehicle Cradle Serial Connection

To provide serial communications between an MC75A and a serial device, connect one end of the 9-pin serial cable into the serial port on the cradle, and the other end into the serial port on the serial device.

NOTE Some devices may require a null modem serial cable.

To begin communication:

1. Insert the MC75A into the cradle.

2. To initiate communication, make appropriate selections on the MC75A, as determined by the application

you are using.

CAUTION Removing the MC75A during data communication disrupts communication between the MC75A and the

attached device.

Charging the MC75A Battery

Insert the MC75A into the vehicle cradle to begin charging. A click indicates that the MC75A button release locking mechanism is enabled and the MC75A is locked in place.

2 - 20 MC75A Enterprise Digital Assistant Integrator Guide

Release Lever

Figure 2-18

MC75A Battery Charging

CAUTION Ensure the MC75A is fully inserted in the cradle. Lack of proper insertion may result in property damage or

personal injury. Zebra is not responsible for any loss resulting from the use of the products while driving.

Removing the MC75A

To remove the MC75A, hold back the release lever on the cradle and pull the MC75A up and out of the cradle.

Figure 2-19

Removing the MC75A

Charging the Spare Battery

Insert a spare battery to begin charging:

1. Lift the battery release lever.

Accessories 2 - 21

Battery Release Lever

Figure 2-20

2. Insert the spare battery in the spare battery charging slot in the cradle with the charging contacts facing up

Inserting the Spare Battery

and to the rear of the cradle.

3. Release the battery release lever. The battery release lever locks the spare battery into place.

To remove a spare battery, hold back the battery release lever and lift the battery from the spare battery slot.

Figure 2-21

Removing the Spare Battery

Battery Charging Indicators

The Vehicle Cradle charges the MC75A’s main battery and a spare battery simultaneously.

The MC75A’s charge LED indicates the status of the battery charging in the MC75A. See Table 1-2 on page

1-4 for charging status indications.

The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle. See Table 2-7 for charging status indications.

The 3600 mAh battery fully charges in approximately five hours and the 4800 mAh battery fully charges in approximately seven hours.

Table 2-7

Vehicle Cradle Spare Battery LED Charging Indicators

Spare Battery LED

(on cradle)

Indication

Slow Blinking Amber Spare battery is charging.

2 - 22 MC75A Enterprise Digital Assistant Integrator Guide

Table 2-7

Solid Amber Spare battery is fully charged.

Fast Blinking Amber Charging error.

Off Not charging.

Vehicle Cradle Spare Battery LED Charging Indicators (Continued)

Spare Battery LED

(on cradle)

Indication

Charging Temperature

Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75A.

Four Slot Battery Charger

This section describes how to use the Four Slot Battery Charger to charge up to four MC75A spare batteries.

Battery Shim Installation

Before charging a spare battery, snap the MC75A shim into the battery slot as shown in Figure 2-22.

Accessories 2 - 23

Figure 2-22

Spare Battery Shim Installation

NOTE To purchase additional shims, contact your local account manager or Zebra. Part number: KT-76490-01R.

Spare Battery Charging

1. Connect the charger to a power source.

2. Insert the spare battery into a spare battery charging well and gently press down on the battery to ensure

proper contact.

2 - 24 MC75A Enterprise Digital Assistant Integrator Guide

Spare Battery

Charging LEDs (4)

Spare Battery

Figure 2-23

Four Slot Spare Battery Charger

Battery Charging Indicators

An amber LED is provided for each battery charging well. See Table 2-8 for charging status indications. The 3600 mAh battery fully charges in approximately five hours and the 4800 mAh battery fully charges in approximately seven hours.

Charging Temperature

Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the charger in order to ensure safe operation and optimize long-term battery life.

To accomplish this, for small periods of time, the charger alternately enables and disables battery charging to keep the battery at acceptable temperatures. The charger indicates when charging is disabled due to abnormal temperatures via its LED. See Table 2-8.

Table 2-8

Off No spare battery in slot; spare battery not placed correctly; cradle is not

Fast Blinking Amber Error in charging; check placement of spare battery.

Spare Battery LED Charging Indicators

LED Indication

powered.

Slow Blinking Amber Spare battery is charging.

Solid Amber Charging complete.

Cables

This section describes how to set up and use the cables. The cables are available with a variety of connection capabilities.

The following MC75A communication/charge cables are available:

The following printer cables are available directly from Zebra.

•

Serial (RS232) Charge cable (9-pin D female with power input receptacle)

•

USB Client Charge cable (standard-A connector and a barrel receptacle for power)

•

Auto charge cable

•

DEX cable

•

Modem inverter cable

•

Charge only cable.

•

O’Neil Printer cable

•

Zebra Printer cable.

Accessories 2 - 25

Figure 2-24

The communication/charge cables:

•

Dedicated printer cables provide communication with a printer.

Cables (MC75A Connector)

Provide the MC75A with operating and charging power.

Synchronize information between the MC75A and a host computer. With customized or third party software, it can also synchronize the MC75A with corporate databases.

Provide serial connection through the serial pass-through port for communication with a serial device, such as a host computer. For communication setup procedures, see Communication Setup on page

2-26.

Provide USB connection through the USB pass-through port for communication with a USB device, such as a host computer. For communication setup procedures, see Communication Setup on page 2-26.

Setup

The MC75A communication/charge cables can connect with a serial/USB device, such as a printer or host computer, through its serial or USB port.

2 - 26 MC75A Enterprise Digital Assistant Integrator Guide

Battery Charging

The communication/charge cables can charge the MC75A battery and supply operating power.

To charge the MC75A battery:

1. Connect the communication/charge cable power input connector to the approved power source.

2. Slide the bottom of the MC75A into the connector end of the communication/charge cable and gently press

in until it latches into the MC75A. The MC75A amber Charge LED indicates the MC75A battery charging status. The 3600 mAh battery fully charges in approximately five hours and the 4800 mAh battery fully charges in approximately seven hours. See Table 1-2 on page 1-4 for charging status indications.

3. When charging completes, remove the cable by gently pulling the MC75A and the cable apart.

LED Charge Indications

The amber Charge LED on the MC75A indicates battery charging status. See Table 1-2 on page 1-4 for charging status indications.

Charging Temperature

Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75A.

To accomplish this, for small periods of time, the MC75A alternately enables and disables battery charging to keep the battery at acceptable temperatures. The MC75A indicates when charging is disabled due to abnormal temperatures via its LED. See Table 1-2 on page 1-4.

Communication Setup

To connect an MC75A communication/charge cable to a serial or USB device:

1. Connect the serial/USB end of the MC75A communication/charge cable to the communication port of the

device.

2. Connect the MC75A connector end of the cable to the MC75A. For more information on communication

setup procedures, see Chapter 3, ActiveSync.

CHAPTER 3 ACTIVESYNC

Introduction

To communicate with various host devices, install Microsoft ActiveSync (version 4.5 or higher) on the host computer. Use ActiveSync to synchronize information on the mobile computer with information on the host computer. Changes made on the mobile computer or host computer appear in both places after synchronization.

NOTE When a mobile computer with Windows Mobile 6 is connected to a host computer and an ActiveSync

connection is made, the WLAN radio (if applicable) is disabled. This is a Microsoft security feature to prevent connection to two networks at the same time.

ActiveSync software:

•

Allows working with mobile computer-compatible host applications on the host computer. ActiveSync replicates data from the mobile computer so the host application can view, enter, and modify data on the mobile computer.

•

Synchronizes files between the mobile computer and host computer, converting the files to the correct format.

•

Backs up the data stored on the mobile computer. Synchronization is a one-step procedure that ensures the data is always safe and up-to-date.

•

Copies (rather than synchronizes) files between the mobile computer and host computer.

•

Controls when synchronization occurs by selecting a synchronization mode, e.g., set to synchronize continually while the mobile computer is connected to the host computer, or set to only synchronize on command.

•

Selects the types of information to synchronize and control how much data is synchronized.

Installing ActiveSync

To install ActiveSync on the host computer, download version 4.5 or higher from the Microsoft web site at

http://www.microsoft.com. Refer to the installation included with the ActiveSync software.

3 - 2 MC75A Enterprise Digital Assistant Integrator Guide

Mobile Computer Setup

NOTE Microsoft recommends installing ActiveSync on the host computer before connecting the mobile

computer.

The mobile computer can be set up to communicate either with a USB connection. Chapter 2, Accessories provides the accessory setup and cable connection information for use with the mobile computer. The mobile computer communication settings must be set to match the communication settings used with ActiveSync.

1. On the mobile computer tap Start > Programs > ActiveSync icon. The ActiveSync window appears.

Figure 3-1

2. Ta p Menu > Connections.

3. Select the connection type from the drop-down list.

4. Ta p OK to exit the Connections window and tap OK to exit the ActiveSync window.

5. Proceed with installing ActiveSync on the host computer and setting up a partnership.

ActiveSync Window

Setting Up an ActiveSync Connection on the Host Computer

To start ActiveSync:

1. Select Start > Programs > Microsoft ActiveSync on the host computer. The ActiveSync Window displays.

Figure 3-2

ActiveSync Window

ActiveSync 3 - 3

NOTE Assign each mobile computer a unique device name. Do not try to synchronize more than one mobile

computer to the same name.

2. In the ActiveSync window, select File > Connection Settings. The Connection Settings window appears.

Figure 3-3

3. Select the appropriate check box for the type of connection used.

4. Select the Show status icon in Taskbar check box.

5. Select OK to save any changes made.

Connection Settings Window

Synchronization with a Windows Mobile 6 Device

NOTE When a mobile computer with Windows Mobile 6 is connected to a host computer and an ActiveSync

connection is made, the WLAN radio (if applicable) is disabled. This is a Microsoft security feature to prevent connection to two networks at the same time.

To synchronize with a Windows Mobile 6 device:

1. If the Get Connected window does not appear on the host computer, select Start > All Programs > Microsoft

ActiveSync.

Figure 3-4

2. Click Next.

Synchronization Setup Wizard Window

3 - 4 MC75A Enterprise Digital Assistant Integrator Guide

Figure 3-5

3. Select the check box to synchronize with a server running Microsoft Exchange if applicable.

4. Click Next.

Figure 3-6

5. Select the appropriate settings and click Next.

Synchronization Directly With a Server Window

Synchronization Option Window

ActiveSync 3 - 5

Figure 3-7

6. Click Finish.

Figure 3-8

Wizard Complete Window

ActiveSync Connected Window

During the first synchronization, information stored on the mobile computer is copied to the host computer. When the copy is complete and all data is synchronized, the mobile computer can be disconnect from the host computer.

NOTE The first ActiveSync operation must be performed with a local, direct connection. Windows Mobile retains

partnerships information after a cold boot.

For more information about using ActiveSync, start ActiveSync on the host computer, then see ActiveSync Help.

3 - 6 MC75A Enterprise Digital Assistant Integrator Guide

CHAPTER 4 APPLICATION DEPLOYMENT

FOR MOBILE 6

Introduction

This chapter describes new features in Windows Mobile 6 including new security features, how to package applications, and procedures for deploying applications onto the MC75A.

Security

The MC75A implement a set of security policies that determine whether an application is allowed to run and, if allowed, with what level of trust. To develop an application, you must know the security configuration of the device, and how to sign an application with the appropriate certificate to allow the application to run (and to run with the needed level of trust).

Application Security

Application security controls the applications that can run on the MC75A.

•

Trusted - All applications must be digitally signed by a certificate on the MC75A.

•

Prompted - User is prompted to allow unsigned applications to run.

•

Open - All applications run.

Developers can include their own certificates and provision the device to “trusted.”

Digital Signatures

Digital signatures provide a way to authenticate the author of EXEs, DLLs, and packages. Digitally signed applications give users confidence that an application comes from where they think it comes from. For example, if an end-user downloads an update package from the internet that is digitally signed with Zebra's software certificate, they are assured that the package is authentic and that it was created by Zebra. By enforcing the use of digital signatures, users can also prevent malicious applications from executing on the MC75A. For example, users can provision the MC75A to only execute “trusted” applications (digitally signed).

Zebra ships all Windows Mobile 6 based products in an “open” state, which means all signed and unsigned applications should work. However, customers can still reconfigure their MC75As to operate in the “trusted”

4 - 2 MC75A Enterprise Digital Assistant Integrator Guide

mode. This means that only applications signed with a certificate from the Privileged Execution Trust Certificate Store can run.

To support the broadest number of deployments, third-party software developers should perform the following when releasing software for a Windows Mobile 6 devices:

•

Sign all their EXEs & DLLs with their private key

•

Provide the corresponding public certificate to end-users so that it can be installed into Privileged Execution Trust Certificate Store.

If the software is installed via a .CAB file, developer should also:

•

Sign the .CAB file with their private key

•

Provide the corresponding public certificate to end-users so that it can be installed into SPC Certificate Store.

Locking Down a Mobile Computer

Like most configuration options in Windows Mobile 6, security settings are set via XML provisioning. For example, to enforce the “trusted” model and only allow applications signed with a privileged certificate to run, use the following provisioning document:

<wap-provisioningdoc>

</characteristic>

</wap-provisioningdoc>

For more information on various security options, refer to the Security Policy Settings topic in the latest Windows Mobile documentation.

Application Deployment for Mobile 6 4 - 3

Installing Certificates

Use XML provisioning to query and delete certificates from certificate stores. To add a new certificate the Privileged Execution Trust Certificate Store, use the following sample provisioning document:

<wap-provisioningdoc>

<parm name= “EncodedCertificate” value= “

This is sample text. This is sample text. This is sample text. This is sample text.

This is sample text. This is sample text. This is sample text. This is sample text. = “/>

</characteristic>

</wap-provisioningdoc>

To create your own provisioning document with real certificate information:

1. Obtain a certificate from a security provider such as VeriSign.

2. Double-click on the certificate file (.CER) to open it.

3. Click on the Details tab and locate the Thumbprint field.

4. Copy the contents of the Thumbprint field and replace the value in the XML example above.

5. Click the Copy to File… button.

6. Click Next to start the Certificate Export Wizard.

7. Select Base-64 encoded X.509 (.CER) and then click Next.

8. Set the File Name to CertOutput.xml and click Next.

9. Click Finish to export the certificate.

10. Open the exported file, CertOutput.xml, in a text editor (i.e., NotePad).

11. Copy the contents of the file (excluding the first line, last line, and CR/LF) and replace the value of the

“EncodedCertificate” parameter in the xml example above.

Device Management Security

You can control access to certain device settings and security levels, such as installing applications and changing security settings. Refer to the Windows Mobile Version 6 Help file for information on device management security.

Remote API Security

The Remote API (RAPI) enables applications that run on a desktop to perform actions on a remote device. RAPI provides the ability to manipulate the file system on the remote device, including the creation and deletion of files and directories. By default, Zebra ships with RAPI in the restricted mode. Certain tools, such as

4 - 4 MC75A Enterprise Digital Assistant Integrator Guide

RAPIConfig, may not work properly. Refer to the Windows Mobile Version 6 Help file for finding information on Remote API security policies.

Packaging

NOTE Applications compiled for Windows Mobile 6 are not backward-compatible with previous versions.

Packaging combines an application's executable files into a single file, called a package. This makes it easier to deploy and install an application to the MC75A. Package new applications and updates, such as new DLL files, as CAB files, then deploy them to Mobile 6 devices. Refer to the Microsoft Windows Mobile 6 Help file for information on CAB files.

Deployment

To install applications onto the MC75A, developers package the application and all required files into a CAB file, then load the file onto the MC75A using one of the following options:

•

Microsoft ActiveSync 4.1 or higher

•

Storage Card

•

MSP 3.X

•

AirBEAM

•

Image Update (for updating the operating system).

Refer to the Microsoft Windows Mobile 6 Help file for information on CAB files.

Installation Using ActiveSync

To install an application package:

•

Connect the MC75A to a host computer using ActiveSync. See Chapter 3, ActiveSync for more information.

•

Locate the package file on the host computer.

•

In ActiveSync on the host computer, open Explorer for the MC75A.

•

Copy the CAB file from the host computer to the \temp directory on the MC75A.

•

On the MC75A, navigate to the \temp directory.

•

Tap on the application CAB file. The application installs on the MC75A.

Installation Using Storage Card

To install an application package:

•

Copy the package CAB file to a storage card using an appropriate storage card reader.

•

Install the storage card into the MC75A. See Micro Secure Digital (microSD) Card on page 1-7 for more information.

•

On the MC75A, open File Explorer.

Application Deployment for Mobile 6 4 - 5

•

Open the Storage Card directory.

•

Tap the package CAB file. The application installs on the MC75A.

Installation Using AirBEAM

The AirBEAM Smart Client provides backward-compatible legacy AirBEAM functionality and backward-compatible legacy MSP 2.x Level 2 Agent functionality.

Refer to the AirBEAM Smart Windows CE Client Product Reference Guide, p/n 72-63060-01, for instructions for AirBEAM Smart client.

MSP 3.X

The MSP 3 Client Software is a set of software components that come pre-installed on the MC75A. The MSP 3 Client software consists of the following components:

The RD Client provides support for MSP 3 Staging functionality, provides support for the MSP 3 Legacy Staging process, and provides support for backward-compatible legacy MSP 2.x Legacy Staging functionality.

The MSP 3 Agent provides MSP 3 Provisioning functionality and Control functionality when used with MSP 3.2 Control Edition.

Refer to the Mobility Services Platform 3.2 User’s Guide, p/n 72E-100158-xx, for instructions for using the Rapid Deployment and MSP3 Agent clients.

Image Update

Windows Mobile 6 contains an Image Update feature that updates all operating system components. All updates are distributed as update packages. Update packages can contain either partial or complete updates for the operating system. Zebra distributes the update packages on the Support Central Web Site,

http://www.zebra.com/support

To update an operating system component, copy the update package to the MC75A using one of a variety of transports, including ActiveSync, an microSD memory card, or MSP. Then, initiate the update using one of the following methods:

•

Double-tap the package file in File Explorer (similar to extracting a CAB file)

•

Perform a special boot sequence that initiates the update.

NOTE The MC75A must have at least 5 MB of free space to perform an OS update.

To initiate an update:

1. Go to the Support Central web site, http://www.zebra.com/support.

2. Download the appropriate update package.

3. Copy the update package to either the \temp directory on the MC75A, or to a storage card.

4. Connect the MC75A to AC power. See Chapter 2, Accessories.

5. Simultaneously press the Power button and the 1 and 9 keys.

6. Immediately, as soon as the device starts to boot and before the splash screen is visible, press and hold

the right scan button.

4 - 6 MC75A Enterprise Digital Assistant Integrator Guide

7. The Update Loader application first looks for a file on a storage card. If it does not find it, it looks in the

\temp directory.

When it finds the appropriate file, it loads the package onto the MC75A. A progress bar displays until the update completes.

8. The MC75A re-boots.

9. The calibration screen appears.

NOTE When initiating an update via a boot sequence, the update loader looks for updates first on the root of an

installed microSD card and then in the \temp folder on the MC75A’s persistent storage volume. A response file, pkgs.lst, indicates which files to update. In most cases, Zebra provides this pkgs.lst file with the update and you should only modify it when updating a splash screen partition. See Creating a Splash

Screen for more information.

Creating a Splash Screen

Use a bitmap file to create a customized splash screens for the MC75A. Use Image Update with a bitmap file, rather than a package file, to update the splash screen.

To create a custom splash screen:

1. Create a .bmp file using a graphic program with the following specifications:

•

Size: 592 x 480.

•

Colors: 16 bits per pixel (65536 colors) for color displays.

2. Modify the bitmap file and save.

To load the splash screen on the MC75A:

1. Create a text file named pkgs.lst which contains the name of the bmp file. For example, mysplash.bmp.

2. Copy the bmp file and the pkgs.lst file to one of the following:

•

SD card root directory

•

MC75A’s \temp directory

•

MC75A’s \Windows directory.

3. If using an SD card, insert the SD card into the MC75A.

4. Perform a cold boot.

5. Press the trigger or side scan button for 5 seconds while booting to invoke the Update Loader and install

the splash screen.

XML Provisioning

To configure the settings on an MC75A, use XML provisioning. To install an XML provisioning file on the MC75A, create a Cabinet Provisioning File (CPF). A CPF file is similar to a CAB file and contains just one file: _setup.xml. Like a CAB file, the CPF extension is associated with WCELoad.EXE. Opening a CPF extracts the XML code and uses it to provision and configure the MC75A. The user receives an e-mail notification indicating success or failure.

XML provisioning provides the ability to configure various features of the MC75A (i.e., registry and file system). However, some settings require security privileges. To change registry settings via a CPF file, you must have

Application Deployment for Mobile 6 4 - 7

certain privileges (roles). Some registry keys require you to simply be an Authenticated User, while other registry keys require you to be a Manager. Refer to the Microsoft Windows Mobile 6 Help file, Metabase Settings for Registry Configuration Service Provider section, for the default role settings in Windows Mobile 6.

For those registry settings that require the Manager role, the CPF file must be signed with a privileged certificate installed on the device. Refer to the Microsoft Windows Mobile 6 Help file and the Windows Mobile 6 SDK for instructions and sample test certificates.

Creating an XML Provisioning File

To create a .cpf file:

1. Create a valid provisioning XML file named _setup.xml using an XML editor or the tools supplied with

Visual Studio 2005. (For example, use the SampleReg.xml sample created in the RegMerge section and

rename it _setup.xml.) Ensure the file contains the required parameters for the operation. Refer to the

Microsoft Windows Mobile 6 Help file for information.

2. In the Windows Mobile 6 tools directory on the desktop computer (typically \Program Files\Windows CE

Tools\wce500\Windows Mobile 6 Pocket PC SDK\Tools), run the Makecab.exe utility, using the following

syntax to create a .cpf file from the _setup.xml file:

MakeCab.exe /D COMPRESS=OFF _setup.xml myOutCpf

NOTE COMPRESS=OFF is required for backward compatibility with Pocket PC.

3. Optionally, use the Authenticode tools to sign the .cpf file.

4. Tap the filename to install.

5. Certain applications and settings require a cold boot to take affect. In these cases, cold boot the MC75A.

Refer to the Windows Mobile Version 6 Help file for more information.

XML Provisioning vs. RegMerge and Copy File

Prior to Windows Mobile 6, Zebra used two drivers (RegMerge and CopyFiles) to update the registry and to copy files during a cold boot. With Mobile 6, Zebra recommends using XML provisioning instead. RegMerge and CopyFiles are supported for backward compatibility but Zebra may eliminate support in the future. The following sections provide examples of how RegMerge and CopyFiles were used, and how to perform the same function using XML provisioning.

RegMerge

RegMerge.dll is a built-in driver that allows updating the registry during a clean boot. RegMerge runs very early in the boot process and looks for registry files (.reg files) in certain Flash File System folders (i.e., \Application) during a clean boot. It then merges the registry changes into the system registry located in RAM.

The following example uses RegMerge to set a registry key:

SampleReg.reg

[HKEY_LOCAL_MACHINE\Hardware\DeviceMap\Backlight]

“BacklightIntensity”=dword:00000036

The following example uses XML provisioning to perform the same task:

4 - 8 MC75A Enterprise Digital Assistant Integrator Guide

SampleReg.xml

<wap-provisioningdoc>

</characteristic>

</wap-provisioningdoc>

CopyFiles

CopyFiles copies files from one folder to another on a clean boot. During a clean boot CopyFiles looks for files with a .CPY extension in the root of the Application FFS partition. These files are text files containing the source and destination for the desired files to copy, separated by “>”.

The following example uses CopyFiles to copy a file from the \Application folder to the \Windows folder:

SampleCpy.cpy

The following example uses XML provisioning to perform the same task:

SampleCpy.xml

Storage

\Application\example.txt > \Windows\example.txt

<wap-provisioningdoc>

</characteristic>

</wap-provisioningdoc>

Mobile 6 contains three types of file storage:

•

Random Access Memory (RAM)

•

Persistent Storage

•

Application folder.

Application Deployment for Mobile 6 4 - 9

Random Access Memory

Executing programs use RAM to store data. Data stored in RAM is lost upon a warm boot. RAM also included a volatile file storage area called Cache Disk.

Volatile File Storage (Cache Disk)

Windows Mobile 6 memory architecture uses persistent storage for all files, registry settings, and database objects to ensure data is retained even after a power failure. Persistent storage is implemented using Flash memory technology which is generally slower than volatile RAM memory. In certain situations the speed of the operation is more important than the integrity of the data. For these situations, Zebra has provided a small volatile File Storage volume, accessed as the Cache Disk folder. Disk operations to the Cache Disk folder are much faster than to any of the persistent storage volumes, but data is lost across warm boots and power interruptions. Note that a backup battery powers RAM memory, including the Cache Disk, when you remove the main battery for a short period of time.

The MC75A uses the Cache Disk for temporary data that can be restored from other sources, for example, for temporarily “caching” HTML web pages by a browser or generating formatted files to send to a printer. Both situations benefit from the increased speed of the cache disk, but you can restore the data if needed.

DO NOT use the Cache Disk as a method to improve application performance. Analyze applications that perform slower in persistent storage to optimize disk access. Common areas for optimization include minimizing the number of reads and writes to a file, removing unneeded debug logging, and minimizing file flushing or closing files.

Persistent Storage

Windows Mobile 6 protects all data and applications from power-related loss. Because Windows Mobile 6 mounts the entire file system and registry in persistent storage (rather than using RAM), MC75A devices provide a reliable storage platform even in the absence of battery power.

Persistent storage provides application developers with a reliable storage system available through the standard file system and registry APIs. Persistent storage is optimized for large reads and writes; therefore, applications reading and writing data in large chunks tend to outperform those applications reading and writing small blocks of data. Data in persistent storage is lost upon a clean boot.

Persistent storage contains all the directories under the root directory except for Application, Cache Disk, and Storage Card (if a storage card is installed). Persistent storage is approximately 700 MB (formatted).

Application Folder

The Application folder is a super-persistent storage that is persistent even after a clean boot. Accessing data in the Application folder is slower than accessing persistent storage. The Application folder is used for deployment and device-unique data. For example, network profiles can be stored in the Application folder so that connection to the network is available after a cold boot. The Application folder is approximately 110 MB (formatted).

System Configuration Manager

System Configuration Manager (SCM) is a utility that runs on the development computer and is used to create configuration files. These files, when deployed to an MC75A, set configuration parameters for that device. The configurable options for a MC75A are defined in an XML file that is available on the Support Central (http://www.zebra.com/support

SCM eliminates the potential user errors that occur when manually editing registry settings.

) for that MC75A. SCM is also available on Support Central.

4 - 10 MC75A Enterprise Digital Assistant Integrator Guide

File Types

SCM uses three types of files:

•

System Configuration Template (.SCT) files are XML files that define the configurable parameters for a device.

•

Registry Configuration Service Provider XML files for device provisioning.

•

CAB Provisioning Format (.CPF) file which is a .CAB archive that contains the provisioning XML. This file is downloaded to the MC75A and merged upon a cold boot.

User Interface

SCM's user interface consists of a tree control on the left side of the window which displays all the configuration categories, and a data grid table on the right which displays all the configurable controls for the selected category. Figure 4-1 shows the main window for a device’s .sct file.

Figure 4-1

Main SCM Window

Menu Functions

Use the main menu to access the program functionality described in Table 4-1.

Table 4-1

File Menu

Open Config File Open a saved configuration file (.SCD).

Save Config Changes Save changes to the currently loaded configuration file.

Restore All Defaults Restore all parameter values to the default state. The default values are stored in

Export Changes to .xml Export the changed parameter values to an XML file.

SCM Menu Functions

Menu Item Description

a System Configuration template file (i.e., MC75Aw.sct).

Application Deployment for Mobile 6 4 - 11

Table 4-1

Export Changes to .cpf Export the changed parameter values to an CPF file.

Export all to .xml Export all the parameter values to an XML file.

Export all to .cpf Export all the parameter values to an CPF file.

Exit Exit System Configuration Manager.

Device Menu

Device type Change the current device type template. Each template (available from the

Help Menu

About Display the About dialog which shows the application version.

SCM Menu Functions (Continued)

Menu Item Description

Support Central) must reside in the SCM directory.

Parameter State Indicators

The first column of the data table displays parameter state indicators. The state indicators display one of the states in Table 4-2 for a particular parameter:

Table 4-2

Parameter Status Indicators

Icon Indicator Description

Modified This parameter was changed from its initial factory setting.

Invalid This parameter is not valid for the selected device type. This can occur when a

configuration file for one type of device is loaded and the device type is changed using the Device menu. Values marked “invalid” are not included in an exported.

Window Status Bar

The SCM status bar found on the bottom right corner of the window contains the items in Table 4-3 from left to right:

Table 4-3

Invalid Count Number of parameters not valid for the selected device.

Modified Count Number of parameters modified from the factory defaults.

Device Type Device type - version.

Window Status Bar Items

Status Bar Item Description

Figure 4-2

Sample Status Bar

4 - 12 MC75A Enterprise Digital Assistant Integrator Guide

The sample status bar in Figure 4-2 shows that the current configuration file contains 1 Invalid Parameter and 2 Modified Parameters.

File Deployment

The CPF file created by the SCM export function must be deployed to the MC75A.

1. Optionally, use the Authenticode tools to sign the .cpf file.

2. Make the .cpf file read-only, then copy it to the MC75A.

3. Tap the filename to install.

4. Certain applications and settings require a cold boot to take affect. In these cases, cold boot the MC75A.

Refer to the Windows Mobile Version 6 Help file for more information.

Enterprise Mobility Developer Kits

The Enterprise Mobility Developer Kit (EMDK) family of products allows you to write applications that take advantage of the capture, move and manage capabilities of the MC75A. Go to the Support Central (http://www.zebra.com/support

) to download the appropriate developer kit.

CHAPTER 5 MC75A6 - GSM

CONFIGURATION

Introduction

This chapter explains how to verify MC75A6 service on an Global System for Mobile communications (GSM) wireless network and establish settings.

GSM networks deliver mobile voice and data services, such as Short Message Service (SMS)/Text Messaging, with full roaming capabilities across the world. High-speed Downlink Packet Access (HSDPA) enabled networks offer Internet-based content and packet-based data services. This enables services such as internet browsing, e-mail on the move, powerful visual communications, multimedia messages, and location-based services.

When using the MC75A as a phone, services can include speed dialing, call tracking, voice mail, call forwarding, conference calling, and caller ID, depending on the type of service.

Also use the integrated phone as a modem to connect the MC75A to an ISP or work network. The GSM enabled MC75A can connect to the Internet or work network using Cellular Line, or using the modem specified by the mobile phone service provider.

NOTE Before using an MC75A on a wireless network, first select a provider, establish a voice and data-enabled

service plan, and configure the MC75A (where applicable). Refer to the MC75A User Guide for information on how to use the phone and services.

Quick Startup Steps

To use the MC75A for phone and data connections:

1. Install the MC75A main battery. See Installing the Main Battery on page 1-2.

2. Fully charge the main battery and backup battery. See Charging the Battery on page 1-3.

3. Press the red Power button to suspend the MC75A.

4. Remove the battery.

5. Lift the SIM cover using the stylus tip.

5 - 2 MC75A Enterprise Digital Assistant Integrator Guide

SIM Cover

Figure 5-1

6. Insert the SIM card, as shown in Figure 5-2, with the cut edge of the card facing out and the contacts facing

Lifting the SIM Cover

down.

Figure 5-2

7. Lower the SIM cover and use the stylus to slide it in place.

8. Replace the battery and battery cover.

9. Press the red Power button.

10. Ta p Start > Phone > Menu > Options > Network tab and verify that the service provider appears in the Current network: field. If the service provider name does not appear see Chapter 9, Maintenance and

Inserting the SIM Card

Troubleshooting for more information.

11. Make a call to verify connection.

12. Start the MC75A.

13. Ensure network coverage ( page 5-3).

14. Configure a data connection ( page 5-4).

NOTE Data connection configuration is pre-packaged with T-Mobile service. Other service providers may require

data connection configuration

15. Configure settings ( page 5-8).

16. Use the phone.

MC75A6 Service Verification

MC75A6 phone and data services require a live SIM card, obtained from a service provider, installed in the MC75A phone. The SIM card has embedded circuitry on one side of its surface which, when inserted into an MC75A phone, provides phone service. The SIM card provides a phone number, determines the features or services available to the subscriber, and identifies the subscriber to the network.

In addition to SIM card installation, the MC75A may require various settings to operate as a phone with data connection features.

Ensuring Network Coverage

1. Ensure an activated SIM card, from the phone service provider, is installed in the MC75A.

NOTE The SIM card must be enabled to connect to the network.

2. Verify active phone and data services by tapping to display the Phone dialog. The Carrier name

appears in the dialog box.

MC75A6 - GSM Configuration 5 - 3

Figure 5-3

3. Verify SIM card functionality:

a. Ta p Start > Settings > Personal folder > Phone icon > Network tab.

Figure 5-4

Connectivity Dialog

Phone Settings Window - Network Tab

5 - 4 MC75A Enterprise Digital Assistant Integrator Guide

b. Ensure the service provider’s network appears in the Current network: field.

c. If the network does not appear, tap Find Network. If the network still does not appear, verify that the

SIM card was installed correctly. If it was, and no network appears, contact the service provider.

Configuring a Data Connection

A data connection allows Internet access across a wireless network.

To set up a new data connection:

1. Acquire an Access Point Name (APN) from the service provider.

2. Ta p Start > Settings > Connections tab > Connections icon > Tasks tab.

Figure 5-5

3. Under My ISP select Add a new modem connection.

Figure 5-6

4. Enter a connection name in the Enter a name for the connection: text box.

5. Select Cellular Line (GPRS) from the Select a modem: drop-down list.

6. Ta p Next.

Connections Window

Connections Window - Make New Connection

MC75A6 - GSM Configuration 5 - 5

Figure 5-7

7. Enter the APN from the service provider in the Access point name: text box.

8. Ta p Next.

Figure 5-8

9. Enter a username in the User name text box, if required by the service provider.

10. Enter a password in the Password text box, if required by the service provider.

11. Enter a domain name in the Domain text box, if required by the service provider.

Connections Window - Access Point Name

Connections Window - User Name & Password

12. Ta p Finish.

13. Ta p OK to exit Connections.

Establishing a Data Connection

1. Ensure a SIM card is installed in the MC75A.

2. Configure a GPRS data connection. See Configuring a Data Connection on page 5-4.

3. Tap the connectivity icon , or at the top of the screen.

5 - 6 MC75A Enterprise Digital Assistant Integrator Guide

Figure 5-9

4. Ta p Settings.

5. Ta p Connections icon.

6. Ta p Managing existing connections.

7. Tap and hold on the data connection until a menu appears.

Figure 5-10

8. Select Connect.

Connectivity Dialog Box

Data Connection

Figure 5-11

Connecting Using GPRS

MC75A6 - GSM Configuration 5 - 7

9. If the SIM card is protected with a Personal Identification Number (PIN), a dialog box pops up requesting

the appropriate PIN to unlock the SIM card. In this case, enter the PIN and tap

NOTE Place emergency calls at any time, without entering a PIN or a SIM card.

10. When a connection is established, launch Internet Explorer to browse the Internet or launch an applicable

OK.

application.

Ending a Data Connection

To cancel a data connection in progress, tap Cancel in the Connecting... dialog window.

To end an established data connection:

1. Tap, , or to display the Connectivity dialog box.

Figure 5-12

2. Ta p Disconnect.

Connectivity Dialog Box

NOTE Tapping Disconnect during an active data transfer (e.g., downloading a web page) automatically

reconnects the connection. You cannot disconnect the connection until the data transfer is complete

5 - 8 MC75A Enterprise Digital Assistant Integrator Guide

MC75A6 Settings

Use the Phone Settings window to customize settings, such as the ring type and ring tone for incoming calls, security options, and other options depending on the type of service.

Phone

Use the Phone tab to customize ring type, ring tone, keypad tone, and security options.

Ta p

Start > Settings > Personal folder > Phone icon > Phone tab

Start > Phone > Menu > Options > Phone tab.

Figure 5-13

MC75A Phone Window - Phone Tab

Sounds

1. Phone Number automatically displays on the Phone tab when a live SIM card is installed.

2. Select a ring type from the Ring type: drop-down list. The ring type changes the way the MC75A rings

when you receive an incoming call. Regardless of the ring type selected, a dialog box appears on the MC75A’s display for incoming calls.

3. Select a ring tone for incoming calls from the Ring tone: drop-down list. To hear a sample of the selected

ring tone, tap . Tap to end the ring tone.

NOTE To use custom .wav, .mid, or .wma files as ring tones, use ActiveSync on the host computer to copy the

file to the /Windows/Rings folder on the MC75A. Then select the sound from the ring tone list

4. Select a keypad tone from the Keypad: drop-down list. This selection determines the tone that sounds

when entering a phone number on the keypad.

Select keypad. Select

Short tones or Long tones to specify the duration of the sound when you press a number on the

Off to disable tones.

NOTE Turning off sounds saves power and prolongs battery life.

MC75A6 - GSM Configuration 5 - 9

Security

Enabling a PIN

NOTE Place emergency calls at any time, without requiring a PIN or a SIM card.

To require a PIN when using the phone:

1. From the Phone tab (Figure 5-13), select the Require PIN when phone is used check box under Security.

Figure 5-14

2. Use the touch keypad to enter a four to eight digit PIN.

3. Ta p Enter to enable the PIN and return to the Phone tab.

Enter PIN

Changing a PIN

CAUTION If you enter an incorrect PIN, the message “SIM PIN incorrect: Try again” appears. After three

consecutive incorrect attempts, the SIM card is blocked. The phone does not allow you to attempt to enter your PIN again and you must obtain a PIN Unblock Key from your service provider.

1. From the Phone tab (Figure 5-13), tap Change PIN.

2. Use the touch keypad to enter the current PIN.

3. Ta p Enter.

4. Use the touch keypad to enter a new four to eight digit PIN.

5. Ta p Enter.

6. Reenter the new PIN for confirmation and tap Enter.

7. Ta p OK to confirm the change.

Disabling a PIN

1. From the Phone tab (Figure 5-13), deselect the Require PIN when phone is used check box.

2. Use the touch keypad to enter the current PIN.

3. Ta p Enter.

4. Ta p OK to confirm the change.

5 - 10 MC75A Enterprise Digital Assistant Integrator Guide

5. Ta p OK to exit settings.

Services

Use the Services tab to configure settings for subscribed phone services. For example, block certain types of incoming and/or outgoing calls ( page 5-10), disclose the caller’s identity when making outgoing calls ( page

5-11), forward incoming calls to a different phone number ( page 5-11), receive notification of incoming calls

when a phone session is in use ( page 5-12), and set up voice mail and short message service ( page 5-12).

1. Ta p Start > Settings > Personal folder > Phone icon > Services tab.

Start > Phone > Menu > Options > Services tab.

Figure 5-15

2. Select a service from the list and tap Get Settings... .

3. Change services settings as follows.

MC75A Phone Window - Services Tab

Call Barring (Call Blocking)

Use call barring to block certain types of incoming and/or outgoing calls. Select the type of incoming and/or outgoing calls to block.

Figure 5-16

Call Barring/Call Blocking

MC75A6 - GSM Configuration 5 - 11

Caller ID

Enable caller ID to reveal the identity of the person making an outgoing call. Select the Everyone radio button to always display the caller ID. Select the others.

No one radio button to prevent the caller’s identity from appearing to

Figure 5-17

Caller ID

Call Forwarding

NOTE Call Forwarding may not be available on all networks. Check with your service provider for availability.

Use call forwarding to forward incoming calls to a different phone number.

•

To forward all calls to a different phone number:

• select the

• enter the phone number to receive forwarded calls in the

•

To forward incoming calls to a different phone number based on a specific situation, select one or more of the check boxes under

•

No answer: enter the phone number to receive forwarded calls only when the phone cannot be

answered. Then select a time period from the 25, and 30 seconds.

•

Unavailable: enter the phone number to receive forwarded calls only when the phone is turned off or

the user is unreachable.

•

Busy: enter the phone number to receive forwarded calls only when the line is busy.

Forward all incoming phone calls check box.

To: text box.

Forward phone calls only if:.

Forward after: drop-down list. Options are 5, 10, 15, 20,

5 - 12 MC75A Enterprise Digital Assistant Integrator Guide

Figure 5-18

Call Forwarding

Call Waiting

NOTE Call Waiting may not be available on all networks. Check with your service provider for availability.

Call waiting notifies you of an incoming call when the phone is in a phone session. Select the Notify me radio button to enable call waiting. Select the

Figure 5-19

Call Waiting

Do not notify me radio button to disable call waiting.

Voice Mail and Text Messages

To use voice mail and send short messages, enter the voice mail and/or text message phone number in the appropriate text boxes.

MC75A6 - GSM Configuration 5 - 13

Figure 5-20

Voice Mail and Text Messages

Fixed Dialing

Use Fixed Dialing to restrict the phone to dial only the phone number(s) or area code(s) specified in a Fixed Dialing list.

1. Select Fixed Dialing and tap Get Settings.

Figure 5-21

2. Select the Enable fixed dialing check box.

Fixed Dialing Window

3. To add a number to the list, tap Menu > Add.

4. Enter the phone number or area code to restrict and tap Done.

5. Repeat steps 3 and 4 to add more numbers, and tap Done twice when complete.

6. Enter PIN2 and tap Done.

Network

Use the Network tab to view available networks, determine the order in which the phone accesses another network if the current network is unavailable, and specify whether to change networks manually or automatically. The current network remains active until it’s changed, the signal is lost, or the SIM card is changed.

The network the MC75A currently uses appears in the

Current network: field at the top of the window.

5 - 14 MC75A Enterprise Digital Assistant Integrator Guide

Changing Networks Manually

1. Ta p Start > Settings > Personal folder > Phone icon > Network tab

Start > Phone > Menu > Options > Network tab.

Figure 5-22

2. From the Network selection drop-down list, select Manual.

Figure 5-23

3. From the Choose Network window, select the network to use.

4. Ta p OK.

MC75A Phone Window - Network Tab

Choose Network

Viewing Available Networks

To view all wireless networks available:

1. Ta p Start > Settings > Personal folder > Phone icon > Network tab.

Start > Phone > Options > Network tab.

MC75A6 - GSM Configuration 5 - 15

Figure 5-24

2. Ta p Find Network.

Figure 5-25

3. From the Choose Network window, select the network to use.

4. Ta p OK.

MC75A Phone Window - Network Tab

Choose Network

Setting Preferred Networks

Set networks in a preferred order of access. Setting preferred networks allows the MC75A to access a second preferred network if the first is unavailable.

1. Ta p Start > Settings > Personal folder > Phone icon > Network tab

Start > Phone > Menu > Options > Network tab.

Figure 5-26

2. Ta p Set Networks to view all available networks.

MC75A Phone Window - Network Tab

5 - 16 MC75A Enterprise Digital Assistant Integrator Guide

Figure 5-27

3. Select the preferred networks by tapping one or more check boxes.

4. Ta p Move Up and Move Down, as necessary, to place the selected networks in the preferred order.

5. Ta p OK to send the new settings to the network.

6. From the Network tab, select Automatic from the Network selection drop-down list.

7. Ta p OK to exit settings.

Preferred Networks

Phone Info

Use the Phone Info tab to view hardware and software information about the phone.

1. Ta p Start > Settings > Personal folder > Phone icon > Phone Info tab

Start > Phone > Menu > Options > Phone Info tab.

Figure 5-28

2. Ta p OK to exit settings.

MC75A Phone Window - Phone Info Tab

Network Time Synchronization

The MC75A can be configured to synchronize the clock with the time from the carrier network. A registry key on the MC75A has to be created to enable this feature.

Using a registry editor, navigate to the following:

[HKEY_LOCAL_MACHINE\SOFTWARE\Symbol\RIL\RHA\HC25]

Create the following key:

“SyncSystemTime”=dword:00000001

where:

dword:0 = disabled

dword:1 = enabled

After setting the registry key, warm boot the MC75A.

MC75A6 - GSM Configuration 5 - 17

Enhanced Operator Name String

The MC75A is enabled to download and display the name of the GSM network currently logged in to. Four registry keys on the MC75A have to be edited to disable this feature.

Using a registry editor, navigate to each of the following:

[HKEY_LOCAL_MACHINE\Software\Microsoft\RIL]

[HKEY_LOCAL_MACHINE\Software\Microsoft\RIL\Configurations\GSM_HC25]

[HKEY_LOCAL_MACHINE\Comm\Cellular\Ril]

[HKEY_LOCAL_MACHINE\Comm\Cellular\Ril\Configurations\GSM_HC25]

Edit the following key:

“EonsEnable”=dword:1

where:

dword:0 = disabled

dword:1 = enabled (default)

After setting the registry key, warm boot the MC75A.

Service Provider Name Display

The reg key (“UseServiceProviderName”) originally was used to fix the dual-line SIM card issue with value 2. But for the Italian Post, the value 1 should be used to show the virtual carrier name (Poste Mobile).

[HKEY_LOCAL_MACHINE\Software\Microsoft\RIL]

“UseServiceProviderName”=dword:1

5 - 18 MC75A Enterprise Digital Assistant Integrator Guide

where:

dword:0 = Display network provider name

dword:1 - Display service provider name (default)

dword:2 - Display both network provider and service provider name

CHAPTER 6 MC75A8 - CDMA

CONFIGURATION

Introduction

This chapter explains how to activate an MC75A8 on a Code Division Multiple Access (CDMA) wireless network and establish settings.

CDMA is a form of wireless multiplexing in which data (e.g., Short Message Service) can be sent over multiple frequencies simultaneously, optimizing the use of available bandwidth. In an CDMA system data is broken into packets, each of which are given a unique identifier, so that they can be sent out over multiple frequencies and then re-built in the correct order by the receiver.

When using the MC75A as a phone, services can include speed dialing, call tracking, voice mail, call forwarding, conference calling and caller ID, depending on the type of service.

The integrated phone in the MC75A can also be used as a modem to connect the MC75A to an ISP or work network. The MC75A can connect to the Internet or work network using Cellular Line, or using the modem specified by the mobile phone service provider.

NOTE Before the MC75A can be used on a CDMA wireless network, a provider must be selected, a voice and

data-enabled service plan must be established and the MC75A must be properly configured (where applicable).

Refer to the MC75A User Guide for information on how to use the phone and services.

Quick Startup Steps

To start using the MC75A for phone and data connections:

1. Install the main battery (Installing the Main Battery on page 1-2).

2. Activate the phone (CDMA Phone Activation on page 6-2).

3. Configure settings (CDMA Settings on page 6-8).

4. Use the phone.

6 - 2 MC75A Enterprise Digital Assistant Integrator Guide

CDMA Phone Activation

CDMA phone service is available from a number of service providers including Sprint® and Verizon Wireless®. In addition to service activation for each provider, various settings may be required for the MC75A to operate as a phone. There can be different Activation Wizards depending upon the carrier. Verizon Wireless and Sprint use an automatic activation processes. All other carriers use the manual activation process.

Verizon Wireless Activation

The Activation Wizard allows automatic activation. To activate the MC75A using the automated service, the MC75A attempts to call the network on a special number that automatically downloads the phone number and identification codes from the network.

Verizon Wireless automatically downloads the provisioning data. This process is invisible to the user and occurs once, after account activation, during the first data connection attempt.

NOTE After an MC75A is provisioned for Verizon Wireless service, it is strongly recommended that no other

service provider loads are downloaded to the provisioning information.

MC75A and no changes are made to any of the

To activate the phone using the Verizon Wireless automated service:

1. Ensure the MC75A is in a strong signal area.

2. The Activation Wizard automatically starts whenever the phone is turned on. If the wizard does not appear,

tap

Start > Phone > Menu > Activation Wizard... .

Figure 6-1

3. Ta p Auto to connect to the Verizon Wireless Network to automate activation. Automated activation

Verizon Activation Wizard

provides all required codes and identification numbers over the network. No additional activation setup is required.

4. Ta p Finish to close the Activation Wizard.

NOTE If activation was not successful, contact the service provider.

5. The phone can be used in approximately four hours, depending on the network provider load.

MC75A8 - CDMA Configuration 6 - 3

Sprint Activation

Automatic Activation

To activate the phone using Sprint service:

1. Ensure the MC75A8 is in a strong signal area.

2. The Activation Wizard automatically starts whenever the phone is turned on.

Figure 6-2

3. Ta p Provision. If communication with the network is successful, a confirmation window appears.

Figure 6-3

4. Ta p Yes.

5. Automatic provisioning begins. Upon successful activation, a confirmation window appears.

Activation Wizard

Activation Wizard Confirmation Window

6 - 4 MC75A Enterprise Digital Assistant Integrator Guide

Figure 6-4

Provisioning Complete

If activation is unsuccessful, a window appears to re-try the activation process. Tap Yes to try again.

6. Ta p OK to close the application.

NOTE If activation was not successful, contact the service provider.

Manual Activation

To manually activate the phone:

1. Ensure the MC75A8 is in a strong signal area.

2. Ta p Start > Phone > Menu > Activation Wizard... .

Figure 6-5

3. Ta p Next >.

Activation Wizard

MC75A8 - CDMA Configuration 6 - 5

Figure 6-6

4. Enter the 6-digit activation code from your service provider.

5. Ta p Next >. If the activation code is incorrect, an error dialog box appears.

Figure 6-7

6. Enter the MDN and MSID. The MDN and MSID are the area code and phone number received from the

Activation Wizard - Enter Activation Code

Activation Wizard - MDN and MSID

service provider.

7. Ta p Next >. A confirmation dialog box appears.

Figure 6-8

8. Verify that the MDN and MSIN numbers entered are correct, tap Yes to confirm. The Congratulations!

Activation Wizard - Confirmation

window appears.

6 - 6 MC75A Enterprise Digital Assistant Integrator Guide

Figure 6-9

9. Ta p Finish to complete activation.

Activation Wizard - Activation Complete

NOTE If activation was not successful, contact the service provider.

Activation Test

To test the service.

1. Ta p Start > Phone.

Figure 6-10

2. Ensure the carrier name displays on the window.

3. Make a voice call to ensure activation was successful.

Phone Window - Example

NOTE If activation was not successful, contact the service provider.

Establishing a Data Connection

NOTE Ensure that you have data service activated with your service provider.

A data connection allows Internet access across a wireless network. Data connection is pre-packaged with service accounts.

To verify active data service:

1. Ta p Start > Internet Explorer.

2. In the address bar, enter a URL for a web site.

3. Tap to display the Connectivity dialog. The dialog box displays the data connection information.

MC75A8 - CDMA Configuration 6 - 7

Figure 6-11

Data Connection

6 - 8 MC75A Enterprise Digital Assistant Integrator Guide

CDMA Settings

Use the Phone Settings window to customize CDMA phone settings, such as the ring type and ring tone for incoming calls and other options depending on the type of service.

Phone

Use the Phone tab to customize ring type, ring tone and keypad tone when entering phone numbers.

1. Ta p Start > Settings > Personal folder > Phone icon > Phone tab.

Start > Phone > Menu > Options > Phone tab.

Figure 6-12

2. Phone and voicemail phone numbers automatically display when phone service is activated.

3. Select a ring type from the Ring type: drop-down list. The ring type changes the way the MC75A rings to

Phone Window - Phone Tab

notify the user of an incoming call. Regardless of the ring type selected, a dialog box appears on the display for incoming calls.

4. Select a ring tone for incoming calls from the Ring tone: drop-down list. To hear a sample of the selected

ring tone, tap . Tap to end the ring tone.

NOTE To use custom .wav, .mid or .wma files as ring tones, use ActiveSync on the host PC to copy the file to the

/Windows/Rings folder on the MC75A. Then, select the sound from the ring tone list.

5. Select a keypad tone from the Keypad: drop-down list. This selection determines the tone that sounds

when entering a phone number on the keypad.

a. Select Short Tones for a tone that sounds only for one or two seconds.

b. Select Long Tones for a continuous sound for as long as the number on the keypad is pressed.

c. Select Off to disable tones.

6. Ta p Other Settings... to set additional sounds and notifications for the MC75A.

7. Select the Notify me when voice privacy is unavailable check box to receive a message when dialing.

8. Ta p ok to exit settings.

NOTE Turning off sounds saves power and prolongs battery life.

Zebra MC75A integrator Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Revision History

TABLE OF CONTENTS

ABOUT THIS GUIDE

Introduction

Documentation Set

Configurations

Software Versions

Chapter Descriptions

Notational Conventions

Related Documents and Software

Service Information

Introduction

Unpacking the MC75A

Getting Started

Installing the Main Battery

Charging the Battery

Charging the Main Battery and Memory Backup Battery

Charging Spare Batteries

Charging Temperature

Powering On the MC75A

Calibrating the Screen

Checking Battery Status

Resetting the MC75A

Performing a Warm Boot

Performing a Cold Boot

Performing a Clean Boot

Waking the MC75A

Micro Secure Digital (microSD) Card

Replacing the Main Battery

Installing SAM Cards in MC75A6 HF RFID

Removal

Introduction

Single Slot USB/Serial Cradle

Setup

Charging the MC75A Battery

Charging the Spare Battery

Battery Charging Indicators

Charging Temperature

Four Slot Ethernet Cradle

Setup

Daisychaining Ethernet Cradles

Bandwidth Considerations when Daisychaining

Ethernet Cradle Drivers

Charging and Communication

LED Charging Indicators

Charge LED

Speed LED

Link LED

Charging Temperature

Four Slot Charge Only Cradle

Setup

Charging Temperature

Wall Mount Bracket

VCD7X00 Vehicle Cradle

Requirements

Connector Ports

Connector Pin-Outs

Mounting the Cradle

Power Connection

Serial Device Connection

Charging the MC75A Battery

Removing the MC75A

Charging the Spare Battery

Battery Charging Indicators

Charging Temperature

Four Slot Battery Charger

Battery Shim Installation

Spare Battery Charging

Battery Charging Indicators

Charging Temperature

Cables

Setup

Battery Charging

LED Charge Indications

Charging Temperature

Communication Setup