Zebra MC67NA, MC67ND integrator Guide

Download

MC67 MOBILE COMPUTER

INTEGRATOR GUIDE

MC67 MOBILE COMPUTER

INTEGRATOR GUIDE

72E-161698-06

Rev. A

March 2019

ii MC67 Integrator Guide

No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.

The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Zebra grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Zebra. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Zebra. The user agrees to maintain Zebra’s copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof.

Zebra reserves the right to make changes to any software or product to improve reliability, function, or design.

Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise under any Zebra, intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Zebra products.

Revision History

Changes to the original guide are listed below:

Change Date Description

-01 Rev A 11/30/12 Initial release.

-02 Rev A 8/30/13 Add MC67ND configuration.

-03 Rev A 7/15/14 Add support for Ortus display. Changes due to OEM version 03.46.36 (keylight

-04 Rev A 3/2015 Zebra Rebranding

-05 Rev. A 09/30/15 Add MC67NA Base Model Configuration.

-05 Rev. A 3/2019 Update cleaning procedures.

iii

registry settings, red LED during scanning disabled).

iv MC67 Integrator Guide

Revision History.............................................................................................................................. iii

About This Guide

Introduction ..................................................................................................................................... xi

Documentation Set ......................................................................................................................... xi

Configurations................................................................................................................................. xii

Software Versions..................................................................................................................... xii

Chapter Descriptions ...................................................................................................................... xiii

Notational Conventions................................................................................................................... xiii

Related Documents ........................................................................................................................ xiv

Service Information......................................................................................................................... xiv

Chapter 1: Getting Started

Introduction .................................................................................................................................... 1-1

Unpacking ...................................................................................................................................... 1-1

Getting Started ............................................................................................................................... 1-2

Installing a microSD Card ........................................................................................................ 1-2

Installing the SIM Card ............................................................................................................. 1-3

Installing the Battery ................................................................................................................ 1-4

Charging the Battery ................................................................................................................ 1-5

Charging the Main Battery ................................................................................................. 1-5

Charging Spare Batteries ................................................................................................... 1-6

Charging Temperature ....................................................................................................... 1-6

Powering On the MC67 ............................................................................................................ 1-6

Calibrating the Screen ........................................................................................................ 1-6

Network Activation ......................................................................................................................... 1-7

Activating an MC67ND on a CDMA Network ........................................................................... 1-7

Switching from CDMA to GSM/UMTS ..................................................................................... 1-7

Switching from GSM/UTMS to CDMA ..................................................................................... 1-8

Replacing the Battery ..................................................................................................................... 1-8

Resetting the MC67 ....................................................................................................................... 1-9

Performing a Warm Boot ......................................................................................................... 1-9

vi MC67 Integrator Guide

Performing a Cold Boot ............................................................................................................ 1-9

Performing a Clean Boot .......................................................................................................... 1-10

Waking the MC67 .......................................................................................................................... 1-10

Chapter 2: Accessories

Introduction .................................................................................................................................... 2-1

Single Slot USB Cradle .................................................................................................................. 2-3

Setup ........................................................................................................................................ 2-3

Charging the MC67 Battery ..................................................................................................... 2-3

Charging the Spare Battery ..................................................................................................... 2-4

Battery Charging Indicators ..................................................................................................... 2-4

Charging Temperature ....................................................................................................... 2-5

Single Slot Ethernet/Modem/USB Cradle ...................................................................................... 2-6

Country Settings ...................................................................................................................... 2-6

Setup ........................................................................................................................................ 2-6

Indicators ................................................................................................................................. 2-7

MC67 Software Setup .............................................................................................................. 2-7

Ethernet Setup ................................................................................................................... 2-7

Modem Setup ..................................................................................................................... 2-8

Four Slot Ethernet Cradle .............................................................................................................. 2-9

CRD5500-4000ER Setup ......................................................................................................... 2-9

Daisychaining Ethernet Cradles ......................................................................................... 2-10

LED Indicators (CRD5500-4000ER) .................................................................................. 2-11

CRD5501-4001ER Setup ......................................................................................................... 2-11

Daisychaining Ethernet Cradles ............................................................................................... 2-11

LED Indicators (CRD5501-4001ER) .................................................................................. 2-12

Ethernet Cradle Drivers ........................................................................................................... 2-12

Charging .................................................................................................................................. 2-14

Four Slot Charge Only Cradle ....................................................................................................... 2-15

Setup ........................................................................................................................................ 2-15

Charging Temperature ....................................................................................................... 2-15

Wall Mount Bracket ........................................................................................................................ 2-16

VCD5500 Vehicle Cradle ............................................................................................................... 2-18

Requirements ........................................................................................................................... 2-18

Connector Pin-Outs ........................................................................................................... 2-18

Mounting the Cradle ................................................................................................................. 2-18

Power Connection ..............................................

Charging the MC67 Battery ..................................................................................................... 2-21

Removing the MC67 .......................................................................................................... 2-21

Battery Charging Indicators ..................................................................................................... 2-22

Charging Temperature ....................................................................................................... 2-22

Four Slot Battery Charger .............................................................................................................. 2-23

Spare Battery Charging ........................................................................................................... 2-23

Battery Charging Indicators ..................................................................................................... 2-23

Charging Temperature ....................................................................................................... 2-23

Cables ............................................................................................................................................ 2-25

USB Charging Cable ................................................................................................................ 2-25

Charge Only Cable .................................................................................................................. 2-25

Auto Charge Cable .................................................................................................................. 2-26

Connecting to the MC67 .......................................................................................................... 2-26

...................................................................... 2-19

Table of Contents vii

Battery Charging Indicators ..................................................................................................... 2-27

Charging Temperature ............................................................................................................. 2-27

Vehicle Holder ................................................................................................................................ 2-28

Installation Reminders ............................................................................................................. 2-28

Device Mounting Precautions .................................................................................................. 2-28

Installation ................................................................................................................................ 2-28

Assembly ............................................................................................................................ 2-29

Windshield Installation ....................................................................................................... 2-29

Flat Surface Installation ...................................................................................................... 2-30

Handstrap Replacement ................................................................................................................ 2-32

Removal ................................................................................................................................... 2-32

Installation ................................................................................................................................ 2-33

Chapter 3: Synchronization

Introduction .................................................................................................................................... 3-1

Installing the Sync Software ..................................................................................................... 3-1

MC67 Setup ............................................................................................................................. 3-1

Setting Up a Sync Connection ....................................................................................................... 3-2

ActiveSync ............................................................................................................................... 3-2

Windows Mobile Device Center ............................................................................................... 3-3

Synchronization ....................................................................................................................... 3-3

Chapter 4: WAN GSM Configuration

Introduction .................................................................................................................................... 4-1

MC67 Service Verification .............................................................................................................. 4-1

Ensuring Network Coverage .................................................................................................... 4-1

Manually Configuring a Data Connection ................................................................................ 4-2

Establishing a Data Connection ............................................................................................... 4-4

Ending a Data Connection ....................................................................................................... 4-5

MC67 Settings ............................................................................................................................... 4-7

Sounds ..................................................................................................................................... 4-7

Security .................................................................................................................................... 4-7

Enabling a PIN ................................................................................................................... 4-7

Changing a PIN .................................................................................................................. 4-8

Disabling a PIN .................................................................................................................. 4-8

Services ................................................................................................................................... 4-9

Call Barring (Call Blocking) ................................................................................................ 4-9

Caller ID ............................................................................................................................. 4-9

Call Forwarding .................................................................................................................. 4-10

Call Waiting ........................................................................................................................ 4-11

Voice Mail and Text Messages .......................................................................................... 4-11

Fixed Dialing ...................................................................................................................... 4-11

Network .................................................................................................................................... 4-12

Changing Networks Manually ............................................................................................ 4-12

Viewing Available Networks ............................................................................................... 4-13

Setting Preferred Networks ................................................................................................ 4-13

Phone Info ................................................................................................................................ 4-14

Network Time Synchronization ...................................................................................................... 4-15

Enhanced Operator Name String ................................................................................................... 4-15

viii MC67 Integrator Guide

Service Provider Name Display ..................................................................................................... 4-16

Chapter 5: WAN CDMA Configuration

Introduction .................................................................................................................................... 5-1

CDMA Phone Activation ................................................................................................................ 5-1

Activation Test ......................................................................................................................... 5-1

Establishing a Data Connection ..................................................................................................... 5-2

CDMA Settings .............................................................................................................................. 5-3

Phone ....................................................................................................................................... 5-3

Phone Information .................................................................................................................... 5-3

Services ................................................................................................................................... 5-4

Call Barring (Call Blocking) ................................................................................................ 5-4

Caller ID ............................................................................................................................. 5-4

Call Forwarding .................................................................................................................. 5-4

Call Waiting ........................................................................................................................ 5-5

Voice Mail and Short Message Service (SMS) .................................................................. 5-5

Network Time Synchronization ...................................................................................................... 5-5

Chapter 6: Application Deployment

Introduction .................................................................................................................................... 6-1

Security .......................................................................................................................................... 6-1

Application Security ................................................................................................................. 6-1

Digital Signatures ..................................................................................................................... 6-1

Locking Down a Mobile Computer ..................................................................................... 6-2

Installing Certificates .......................................................................................................... 6-3

Device Management Security .................................................................................................. 6-3

Remote API Security ................................................................................................................ 6-3

Packaging ...................................................................................................................................... 6-4

Deployment .................................................................................................................................... 6-4

Installation Using ActiveSync ................................................................................................... 6-4

Installation Using Storage Card ............................................................................................... 6-4

MSP ......................................................................................................................................... 6-5

Update Loader Image .............................................................................................................. 6-5

MC67NA Devices with Ortus Display ................................................................................. 6-5

Download Update Loader Package ................................................................................... 6-6

ActiveSync ......................................................................................................................... 6-7

microSD Card .................................................................................................................... 6-7

XML Provisioning ........................................................................................................................... 6-7

Creating an XML Provisioning File ........................................................................................... 6-8

XML Provisioning vs. RegMerge and Copy File ...................................................................... 6-8

RegMerge .......................................................................................................................... 6-8

CopyFiles ........................................................................................................................... 6-9

Storage .......................................................................................................................................... 6-9

Random Access Memory ......................................................................................................... 6-10

Volatile File Storage (Cache Disk) ..................................................................................... 6-10

Persistent Storage ................................................................................................................... 6-10

Application Folder .................................................................................................................... 6-10

Enterprise Mobility Developer Kits ................................................................................................. 6-10

Table of Contents ix

Chapter 7: Maintenance & Troubleshooting

Introduction .................................................................................................................................... 7-1

Maintaining the MC67 .................................................................................................................... 7-1

Removing the Screen Protector ..................................................................................................... 7-2

Battery Safety Guidelines .............................................................................................................. 7-2

Cleaning ......................................................................................................................................... 7-3

Approved Cleanser Active Ingredients ..................................................................................... 7-3

Harmful Ingredients .................................................................................................................. 7-4

Cleaning Instructions ............................................................................................................... 7-4

Special Cleaning Notes ............................................................................................................ 7-4

Materials Required ................................................................................................................... 7-4

Cleaning the MC67 .................................................................................................................. 7-4

Housing .............................................................................................................................. 7-4

Display ............................................................................................................................... 7-5

Scanner Exit Window ......................................................................................................... 7-5

Connector ........................................................................................................................... 7-5

Cleaning Cradle Connectors .................................................................................................... 7-5

Cleaning Frequency ................................................................................................................. 7-6

Troubleshooting ............................................................................................................................. 7-6

MC67 ....................................................................................................................................... 7-6

Single Slot USB Cradle ............................................................................................................ 7-8

Four Slot Ethernet Cradle ........................................................................................................ 7-9

Vehicle Cradle .......................................................................................................................... 7-9

Four Slot Battery Charger ........................................................................................................ 7-10

Cables ...................................................................................................................................... 7-10

Magnetic Stripe Reader ........................................................................................................... 7-10

Appendix A: Technical Specifications

MC67 Technical Specifications ...................................................................................................... A-1

MC67 ....................................................................................................................................... A-1

Decode Zones .......................................................................................................................... A-7

SE4500-SR ........................................................................................................................ A-7

SE4500-DL ......................................................................................................................... A-9

SE4500-HDPM ................................................................................................................... A-11

MC67 External Connector Pin-Outs ......................................................................................... A-13

MC67 Accessory Specifications ..................................................................................................... A-14

Single Slot USB Cradle ........................................

Four Slot Battery Charger ........................................................................................................ A-14

Four Slot Charge Only Cradle .................................................................................................. A-15

Four Slot Ethernet Cradle ........................................................................................................ A-15

Magstripe Reader .................................................................................................................... A-16

Vehicle Cradle .......................................................................................................................... A-17

Cables ...................................................................................................................................... A-17

Appendix B: Software

Battery Usage Threshold Setting ................................................................................................... B-1

Registry Setting ........................................................................................................................ B-1

Bluetooth Configuration Setting ..................................................................................................... B-2

Green LED Configuration ............................................................................................................... B-3

.................................................................... A-14

x MC67 Integrator Guide

Keypad Backlight ........................................................................................................................... B-3

Turkish SMS Support ..................................................................................................................... B-3

Glossary

Index

ABOUT THIS GUIDE

Introduction

This Integrator Guide provides information about setting up and configuring the MC67 and it’s accessories.

NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.

Documentation Set

The documentation for the MC67 is divided into guides that provide information for specific user needs.

•

MC67 Quick Start Guide - describes how to get the MC67 up and running.

•

MC67 User Guide - describes how to use the MC67.

•

MC67 Integrator Guide - describes how to set up the MC67 and it's accessories.

•

Enterprise Mobility Developer Kit (EMDK) Help File - provides API information for writing applications.

xii MC67 Integrator Guide

Configurations

This guide covers the following configurations:

Configuration Radios Display Memory

MC67NA Base Model

MC67NA WLAN: 802.11

MC67ND WLAN: 802.11

WAN: HSPA+ WLAN: 802.11

a/b/g/n

WPAN: Bluetooth

v2.1 EDR

GPS: Stand-alone

GPS or A-GPS

a/b/g/n

WPAN: Bluetooth

v2.1 EDR WWAN: GSM/UMTS GPS: Stand-alone

GPS or

A-GPS

a/b/g/n WPAN: Bluetooth

v2.1 EDR WWAN:GSM/UMTS

or 1XRTT/

CDMA GPS: Stand-alone

GPS or

A-GPS

3.5” VGA Color

512 MB RAM/ 2 GB Flash

512 MB RAM/2 GB Flash or 1 GB RAM/8 GB Flash

512 MB RAM/2 GB Flash

Data Capture Options

2D imager or 2D imager and camera

Operating

System

Windows Embedded Handheld 6.5

Windows Embedded Handheld 6.5 Professional

Keypads

Numeric, QWERTY, or Calculator DSD

Numeric, QWERTY, QWERTZ, AZERTY, PIM or DSD

Numeric, QWERTY, QWERTZ, AZERTY or DSD

Software Versions

This guide covers various software configurations and references are made to operating system or software versions for:

•

Adaptation Kit Update (AKU) version

•

OEM version

•

Fusion version

•

Phone version.

AKU Version

To determine the Adaptation Kit Update (AKU) version:

Ta p > Settings > System > About > Version.

The second line lists the operating system version and the build number. The last part of the build number

represents the AKU number. For example, Build 29102.5.3.12.13 indicates that the device is running AKU version 5.3.12.13.

OEM Version

To determine the OEM software version:

Ta p > Settings > System > System Info > System.

Fusion Software

To determine the Fusion software version:

Ta p Status Bar > Wireless Companion > Wireless Status > Versions.

Phone Software

To determine the Phone software version:

Press > > Phone information.

Chapter Descriptions

Topics covered in this guide are as follows:

•

Chapter 1, Getting Started provides information on MC67 configurations and accessories, charging the

battery, and resetting the device.

About This Guide xiii

•

Chapter 2, Accessories describes the accessories available for the MC67 and how to set up power

connections and battery charging capabilities, where applicable.

•

Chapter 3, Synchronization provides instructions on installing ActiveSync and setting up a partnership

between the MC67 and a host computer.

•

Chapter 4, WAN GSM Configuration explains how to configure the phone settings.

•

Chapter 6, Application Deployment provides information for provisioning and deploying applications to

the MC67.

•

Chapter 7, Maintenance & Troubleshooting includes instructions on cleaning and storing the MC67, and

provides troubleshooting solutions for potential problems during MC67 operation.

•

Appendix A, Techni cal Specifications includes tables listing the technical specifications for the MC67 and

its accessories.

•

Appendix B, Software provides registry settings for configuring Bluetooth software and battery threshold

settings.

Notational Conventions

The following conventions are used in this document:

•

“mobile computer” refers to Zebra MC67 family of hand-held computers.

•

Italics are used to highlight the following:

• chapters and sections in this and related documents

• dialog box, window, and screen names

• drop-down list and list box names

• check box and radio button names

• icons on a screen.

xiv MC67 Integrator Guide

Manufacturing label

•

Bold text is used to highlight the following:

• key names on a keypad

• button names on a screen.

•

Bullets (•) indicate:

• action items

• lists of alternatives

• lists of required steps that are not necessarily sequential.

•

Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.

Service Information

If you have a problem with your equipment, contact Zebra Global Customer Support for your region. Contact information is available at: http://www.zebra.com/support

When contacting Global Customer Support, please have the following information available:

•

Serial number of the unit (found on manufacturing label)

•

Model number or product name (found on manufacturing label)

•

Software type and version number.

•

IMEI number.

Zebra responds to calls by e-mail or telephone within the time limits set forth in support agreements.

About This Guide xv

If your problem cannot be solved by Zebra Global Customer Support, you may need to return your equipment for servicing and will be given specific directions. Zebra is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.

If you purchased your business product from a Zebra business partner, contact that business partner for support.

xvi MC67 Integrator Guide

CHAPTER 1 GETTING STARTED

Introduction

This chapter lists the parts and accessories for the MC67 and explains how to set up the MC67 for the first time.

Unpacking

Carefully remove all protective material from the MC67 and save the shipping container for later storage and shipping.

Verify that you received the following:

•

MC67

•

3600 mAh Lithium-ion battery

•

stylus with tether (installed)

•

screen protector, installed on display window

•

Regulatory Guide

•

Quick Start Guide.

Inspect the equipment for damage. If any equipment is missing or damaged, contact the Zebra Global

Customer Support center immediately. See Service Information on page xiv for contact information.

Prior to using the MC67 for the first time, remove the protective shipping film that covers the scan window, display and camera window.

1 - 2 MC67 Integrator Guide

Rubber access door

microSD card holder door

SIM card holder door

Getting Started

To start using the MC67 for the first time:

1. Install a microSD card (optional)

2. Install the SIM card (GSM/UMTS only)

3. Install the battery.

4. Charge the MC67.

Installing a microSD Card

The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack. Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.

CAUTION Follow proper ESD precautions to avoid damaging the SD card. Proper ESD precautions include, but

are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.

To install the microSD card:

1. Remove the handstrap.

2. Lift rubber access door.

3. Slide the SIM card holder door up to unlock.

4. Lift SIM card holder door.

Figure 1-1

5. Lift microSD card holder door.

Lift SIM Slot Holder Door

6. Insert the microSD card into card holder door ensuring that the card slides into the holding tabs on each

side of the door.

Getting Started 1 - 3

microSD card

Holding tab

Figure 1-2

7. Close the card holder door and push down until it is securely into place.

8. If installing a SIM card, proceed to Installing the SIM Card.

9. Close SIM card holder door and slide down until it locks into place.

10. Close rubber access door.

Insert microSD Card in Holder

Installing the SIM Card

NOTE The MC67 does not support copying multiple contacts to some SIM cards. If an error message appears,

see Chapter 7, Maintenance & Troubleshooting for more information.

GSM/UMTS networks only.

GSM phone service requires a Subscriber Identification Module (SIM) card. Obtain the card from the your service provider. The card fits into the MC67 and can contain the following information:

•

Mobile phone service provider account details.

•

Information regarding service access and preferences.

•

Contact information, which can be moved to Contacts on the MC67.

•

Any additional services to which you have subscribed.

NOTE For more information about SIM cards, refer to the service provider's documentation.

To install the SIM card:

1. Lift rubber access door.

2. Slide the SIM card holder up to unlock.

3. Lift the SIM card holder door.

1 - 4 MC67 Integrator Guide

Figure 1-3

4. Insert the SIM card, as shown in Fig ure 1-4 ensuring that the card slides into the holding tabs on each side

Lifting the SIM Cover

of the door.

Figure 1-4

5. Close SIM card holder door and slide down to lock into place.

6. Close the rubber access door.

7. Install the battery.

Inserting the SIM Card

Installing the Battery

To install the battery.

1. Insert the battery, bottom first, into the battery compartment in the back of the MC67.

2. Press the battery down into the battery compartment until the battery release latch snaps (2-clicks) into

place. The MC67 turns on if the battery is properly charged.

3. Replace the handstrap.

Getting Started 1 - 5

Battery

Battery Release Latch

Figure 1-5

Inserting the Battery

Charging the Battery

CAUTION Follow the guidelines for battery safety described in Battery Safety Guidelines on page 7-2.

Charging the Main Battery

Before using the MC67 for the first time, charge the main battery until the amber Charging/Battery Status light

emitting diode (LED) remains lit (see T able 1-1 on page 1-6 for charge status indications). To charge the MC67,

use a cable or a cradle with the appropriate power supply. For information about the accessories available for the MC67, see Chapter 2, Accessories.

The MC67 is equipped with a backup battery which automatically charges from the fully-charged main battery. When using the MC67 for the first time, the backup battery requires approximately 40 hours to fully charge. This is also true any time the backup battery is discharged, which occurs when the main battery is removed for several hours. The backup battery retains random access memory (RAM) data in memory for at least 15 minutes (at room temperature) when the MC67’s main battery is removed. When the MC67 reaches a very low battery state, the combination of main battery and backup battery retains RAM data in memory for at least 36 hours.

For cable and cradle setup and charging procedures refer to the MC67 Integrator Guide.

•

USB Charging Cable

•

Charge Only Cable

•

Single Slot USB Cradle

•

Four Slot Charge Only Cradle

•

Four Slot Ethernet Cradle.

To charge the main battery:

1 - 6 MC67 Integrator Guide

1. Connect the charging accessory to the appropriate power source.

2. Insert the MC67 into a cradle or attach to a cable. The MC67 begins charging. The Charging/Battery Status

LED blinks amber while charging, then turns solid amber when fully charged. See Table 1-1 for charging

indications.

The 3600 mAh battery charges in less than six hours.

Table 1-1

Off MC67 is not charging.

Slow Blinking Amber (1 blink every 2 seconds)

Solid Amber Charging complete.

Fast Blinking Amber (2 blinks/second)

LED Charge Indicators

Charging/Battery

Status LED

Indication

MC67 is not inserted correctly in the cradle or connected to a power source. Charger/cradle is not powered.

MC67 is charging.

Note: When the battery is initially inserted in the MC67, the amber LED flashes once if the battery power is low or the battery is not fully inserted.

Charging error, e.g.:

•

Temperature is too low or too high.

•

Charging has gone on too long without completion (typically eight hours).

Charging Spare Batteries

See Chapter 2, Accessories for information on using accessories to change spare batteries.

Charging Temperature

Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Note that charging is intelligently controlled by the MC67.

To accomplish this, for small periods of time, the MC67 or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. The MC67 or accessory indicates when charging is

disabled due to abnormal temperatures via its LED. See Table 1-1.

Powering On the MC67

NOTE If during installation of the battery, the battery has significant charge the MC67 turns on.

Press the Power button to turn on the MC67. The splash screen displays for about a minute as the MC67 initializes its flash file system, then the calibration window appears.

Calibrating the Screen

NOTE The Calibration screen can be accessed by pressing Blue key then Backspace key.

On the Personal Information Manager (PIM) keypad, tap > Settings > System > Screen > Align Screen.

To calibrate the screen so the cursor on the touch screen aligns with the tip of the stylus:

1. Remove the stylus from its holder on the side of the MC67.

2. Carefully press and briefly hold the tip of stylus on the center of each target that appears on the screen.

3. Repeat as the target moves around the screen, then tap the screen to continue.

Network Activation

Network activation is dependent upon the network type. When an GSM/UTMS SIM card is installed in the MC67ND, upon startup the MC67ND is configured for the GSM/UTMS network.

Activating an MC67ND on a CDMA Network

To activate on a CDMA network:

1. Setup an account with the CDMA carrier. Provide the MEID number (located under the battery of the

MC67ND) to the customer service representative.

2. Ta p Start > Settings > Connections > Network Setup & Activation. The Network Setup & Activation

window displays.

Getting Started 1 - 7

Figure 1-6

3. Ta p Switch to CDMA.

4. The window closes.

5. Ta p Network Setup & Activation.

6. Ta p Activation. The CDMA Activation window appears.

7. Ta p Start Activation and PRL Update.

8. Follow the on-screen instructions.

For detailed information for configuring the phone and activating on a different network, refer to the MC67 Integrator Guide.

Network Setup and Activation Setup Window

Switching from CDMA to GSM/UMTS

To switch from a CDMA network to a GSM/UTMAS network:

1. Ta p Start > Settings > Connections > Network Setup & Activation. The Network & Activation window

appears.

1 - 8 MC67 Integrator Guide

Figure 1-7

2. Ta p Switch to GSNM/UTMS.

3. The window closes.

4. Ta p Network Setup & Activation.

5. In the GSM/UMTS Settings drop-down list, select connection type. Options:

a. Auto (GSM&UTMS)

b. GSM Only

c. UMTS Only.

6. 6. Tap Apply GSM/UMTS Settings.

7. 7. Tap OK.

Network Setup and Activation Setup Window

Switching from GSM/UTMS to CDMA

1. Tap Start > Settings > Connections > Network Setup & Activation. The Network & Activation window appears.

2. Tap Switch to CDMA.

3. The window closes.

Replacing the Battery

To replace the battery:

CAUTION The MC67 backup battery retains data for up to 15 minutes. Replace the battery within 15 minutes to

ensure that application states are maintained and that data is not lost.

1. If the MC67 is in a cradle, remove it before performing a Safe Battery Swap.

2. If the MC67 is in suspend mode, press the red Power button to wake the device.

3. Press the red Power button. The PowerKey Action screen appears.

4. Ta p Safe Battery Swap. The Data Capture LED lights red.

5. When the LED turns off, remove the handstrap.

Battery Latch

6. Slide the battery latch to the right. The battery ejects slightly.

Getting Started 1 - 9

Figure 1-8

7. Lift the battery from the MC67.

8. Insert the replacement battery, bottom first, into the battery compartment in the back of the MC67.

9. Press the battery down until the battery release latch snaps (2-clicks) into place.

10. Replace the handstrap.

Removing the Battery

Resetting the MC67

There are three reset functions; warm boot, cold boot, and clean boot. A warm boot restarts the MC67 by closing all running programs. A cold boot also restarts the MC67, and also initializes some drivers. Data saved in flash memory or a memory card is not lost.

If the MC67 is not functioning properly, perform a warm boot first. If the MC67 still does not respond, perform a cold boot.

Performing a Warm Boot

Hold down the red Power button for approximately five seconds. As soon as the MC67 starts to boot release the Power button.

Performing a Cold Boot

To perform a cold boot:

•

On a numeric and DSD keypad, simultaneously press the red Power button and the and keys.

•

On a Calculator DSD keypad, simultaneously press the red Power button and the and keys.

•

On an alphanumeric keypad, simultaneously press the red Power button and the and keys.

1 - 10 MC67 Integrator Guide

•

On an PIM keypad, simultaneously press the red Power button and the and keys.

Performing a Clean Boot

CAUTION A clean boot should only be performed by an authorized system administrator. You must connect the

MC67 to AC power during a clean boot.

Removing AC power from the MC67 during a clean boot may render the MC67 inoperable.

A clean boot resets the MC67 to the factory default settings. All data in the Application folder is retained. You must download the Clean Boot Package file from the Support Central web site, http://www.zebra.com/support and install on the MC67.

To perform a clean boot:

1. Download the Clean Boot Package from the Support Central web site. Follow the instructions included in

the package for installing the package onto the MC67.

2. Perform a warm boot.

3. Immediately, as soon as the device starts to boot and before the splash screen is visible, press and hold

the left scan button.

4. Insert the MC67 into a powered cradle.

5. The MC67 updates and then resets.

6. Calibrate the screen.

Waking the MC67

The wake-up conditions define what actions wake up the MC67 after it has gone into suspend mode. The MC67 can go into suspend mode by either pressing the Power button or automatically by Control Panel time-out settings. To set the wake up conditions tap > Settings > System > Power > Wakeup.

Table 1-2

MC67 is connected to a USB cable. Yes Yes

MC67 is connected toto a USB Host Device No No

A key is pressed. No Yes

Wake-up Default Settings

Condition for Wake-up Power Button Automatic Time-out

The screen is touched. No No

Right Trigger is pressed. Yes Yes

Left Trigger is pressed. Yes Yes

CHAPTER 2 ACCESSORIES

Introduction

This chapter provides set up information for the MC67 various accessories listed in Table 2-1.

Table 2-1

MC67 Accessories

Accessory Part Number Description

Cradles

Single Slot USB Cradle CRD5500-1000UR Charges the MC67 main battery and a spare battery.

Single Slot Ethernet/Modem/USB Cradle

Four Slot Charge Only Cradle

Four Slot Ethernet Cradle CRD5500-4000ER

Vehicle Cradle VCD5500-1001R Installs in a vehicle and charges the MC67 main battery.

Vehicle Holder VCH5500-1000R Provides an alternative mounting solution for the MC67 in a

Chargers

Four Slot Spare Battery Charger

CRD5500-1000XR Charges the MC67 main battery and a spare battery.

CRD5500-4000CR CRD5501-4000CR

CRD5501-4000ER

SAC5500-4000CR Charges up to four MC67 battery packs.

Synchronizes the MC67 with a host computer through a USB connection.

Synchronizes the MC67 with a host computer through an Ethernet, Modem or USB connection.

Charges up to four MC67 devices.

Charges up to four MC67 devices and connects the MC67 with an Ethernet network. CRD5500-4000ER provides up to a maximum of 100 Mbps. CRD5501-4000ER provides up to a maximum of 1 Gbps.

vehicle. Requires the Auto Charge cable for charging the MC67 battery.

Power Supply PWRS-14000-249R Provides power to the MC67 using the USB Charging Cable

Power Supply PWRS-14000-148R Provides power to the Single Slot USB cradle and Four Slot

or Charge Only Cable.

Spare Battery Charger.

2 - 2 MC67 Integrator Guide

Table 2-1

MC67 Accessories (Continued)

Accessory Part Number Description

Power Supply PWRS-14000-241R Provides power to the Four Slot Charge Only cradle or Four

USB Charging Cable 25-108022-03R Provides power to the MC67 and USB communication with a

Charge Only Cable 25-112560-02R Connects to a power supply to provide power to the MC67.

Auto Charge Cable VCA5500-01R Charges the MC67 using a vehicle’s cigarette lighter.

DC Cable 50-16002-029R Provides power from the power supply to the Four Slot

Miscellaneous

Spare 3600 mAh lithium-ion battery

DEX Cable 25-127558-01R For use with electronic data exchange For example, vending

USB Client Communication Cable

Printer Cable 25-136283-01R Provides connection to a Monarch/Paxar Serial printer.

BTRY-MC55EAB02 BTRY-MC55EAB02-10 BTRY-MC55EAB02-50

25-68596-01R Provides USB communication between the Single Slot USB

Slot Ethernet cradles.

host computer.

cradles.

Replacement 3600 mAh battery. (10-pack) (50-pack)

machines.

Cradle and a host computer.

Trigger Handle TRG5500-101R Adds a gun-style handle with a scanning trigger for

Trigger Handle Hand Strap 21-138874-01R Handstrap for the Trigger handle.

Magnetic Stripe Reader MSR5500-100R Captures data from magnetic stripe cards.

Belt Mounted Rigid Holster SG-MC5511110-01R Clips onto belt to hold the MC67 when not in use.

Fabric Holster SG-MC5521110-01R Soft holder for added protection.

Stylus KT-119150-03R

KT-119150-50R

Spring Loaded Stylus STYLUS-00001-03R

STYLUS-00001-10R

Stylus with Tether Stylus-00003-03R

Stylus-00003-50R

Spare Tether KT-122621-03R

KT-122621-50R

Handstrap SG-MC5523341-03R Replacement handstrap with pin

Wall Mounting Kit KT-136648-01R Use for wall mounting the four slot cradles.

Screen Protector KT-137521-03R Package of 3 screen protectors.

comfortable and productive data capture.

Replacement stylus (3-pack). Replacement stylus (50-pack).

Optional spring loaded stylus (3-pack). Optional spring loaded stylus (10-pack).

Spare stylus with tether (3-pack). (50-pack).

Replacement tether (3-pack). (50-pack).

Single Slot USB Cradle

Power Supply

USB Port

Power Port

AC Line Cord

This section describes how to set up and use a Single Slot USB cradle with the MC67. For USB communication setup procedures see Chapter 3, Synchronization.

The Single Slot USB cradle:

•

Provides 5.4 VDC power for operating the MC67.

•

Synchronizes information between the MC67 and a host computer. See Chapter 3, Synchronization for information on setting up a partnership between the MC67 and a host computer.

•

Charges the MC67’s battery.

•

Charges a spare battery.

Setup

Accessories 2 - 3

Figure 2-1

Single Slot USB Cradle Power and USB Connections

Charging the MC67 Battery

Connect the cradle to power. Insert the MC67 into the MC67 slot to begin charging.

2 - 4 MC67 Integrator Guide

Charge Status LED

Spare Battery

Charging LED

Figure 2-2

MC67 Battery Charging

Charging the Spare Battery

Battery Charging Indicators

Figure 2-3

The Single Slot USB cradle charges the MC67’s main battery and a spare battery simultaneously.

Spare Battery Charging

Accessories 2 - 5

The MC67’s Charging/Battery Status LED indicates the status of the battery charging in the MC67. See Table

1-1 on page 1-6 for charging status indications.

The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle.

See Table 2-2 for charging status indications.

The 3600 mAh battery fully charges in approximately six hours.

Charging Temperature

Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC67.

disabled due to abnormal temperatures via its LED. See Table 1-1 on page 1-6 and Table 2-2.

Table 2-2

Slow Blinking Amber Spare battery is charging.

Solid Amber Spare battery is fully charged.

Fast Blinking Amber Charging error.

Off Not charging.

Spare Battery LED Charging Indicators

Spare Battery LED

(on cradle)

Indication

2 - 6 MC67 Integrator Guide

Power Supply

Ethernet Port Power Port

AC Line Cord

USB Port Phone Port

Ethernet Hub

Single Slot Ethernet/Modem/USB Cradle

This section describes how to set up and use a Single Slot Ethernet/Modem/USB cradle with the MC67. For USB communication setup procedures see Chapter 3, Synchronization.

The Single Slot Ethernet/Modem/USB cradle:

•

Provides 5.4 VDC power for operating the MC67.

•

Connects the MC67 to a host computer using USB, a dial-up network using the modem or an Ethernet network.

•

Charges the MC67’s battery.

•

Charges a spare battery.

Country Settings

The modem defaults to operation with US telephone networks. To operate the modem with other country

telephone networks, it must be configured using an application on the MC67. Download the Cradle Modem Country Configurator Application Software for MC55xx package from the Zebra Support Central web site:

http://www.zebra.com/support.

Following the instructions with the software package to install the application on the MC67. The application includes country selections for all supported countries and automatically programs the modem and adjust its operating parameters to comply with the telephone network in the selected country.

Setup

Figure 2-4

Cradle Setup

Accessories 2 - 7

Modem USB Ethernet

Ethernet/Modem LED

Spare Battery

Charging LED

Speed LED

Link LED

Figure 2-5

Indicators

•

Spare Battery Charging LED - Indicates the charging status of the spare battery.

•

Ethernet/Modem LED - Blinks whenever Ethernet or modem connectivity is established.

•

Speed LED - Lights green indicating that the transfer rate is 100 Mbps. When it is not lit, indicates that

the transfer rate is 10Mbps.

•

Link LED - Blinks yellow to indicate activity, or stays lit to indicate that a link is established. When it is not

lit, indicates there is no link.

Figure 2-6

Connection Switch

Cradle Indicators

MC67 Software Setup

Ethernet Setup

1. Ta p > Settings > Connections tab > Wi-Fi icon.

2. Select Work from the drop-down menu.

3. Select USB/Ethernet Series Adapter from the list box.

4. Ta p Ok.

5. Ta p > Settings > Connections tab > Connections icon.

6. Ta p Advanced tab.

7. Ta p Select Networks button.

8. Select My Work Network from both drop-down menus.

9. Ta p Ok.

2 - 8 MC67 Integrator Guide

10. Tap the Ta sks tab.

11. Select Edit my proxy server.

12. Enable both checkboxes.

13. Ta p Advanced... button.

14. Ta p HTTP type.

15. In the Server text box, enter the proxy server name.

16. In the Port text box, enter the port number.

17. In the User name text box, enter the user name for the proxy server.

18. In the Password text box, enter the password for the proxy server.

19. Ta p ok three times.

20. Perform a warm boot.

Modem Setup

1. Ta p > Settings > Connections tab > Connections icon.

2. Ta p Add a new modem connection.

3. In the Enter a name for the connection text box, enter a name for the connection.

4. In the Select a modem drop-down list, select Modem Cradle on USB.

5. Ta p Next.

6. In the text box, enter the phone number to dial.

7. Ta p Next.

8. In the User name text box, enter the user name, if required.

9. In the Password text box, enter the password, if required.

10. Ta p Finish.

11. To test the connection, tap > Programs > Internet Explorer. Enter a web address.

Four Slot Ethernet Cradle

Yellow Link LED (CRD5500-4000ER) Green 100 LED (CRD5501-4001ER)

Green Speed LED (CRD5500-4000ER) Green 1000 LED (CRD5501-4001ER)

This section describes how to set up and use a Four Slot Ethernet cradle with the MC67.

The Four Slot Ethernet cradle:

•

Provides 5.4 VDC power for operating the MC67.

•

Connects the MC67 (up to four) to an Ethernet network.

•

Simultaneously charges up to four MC67s.

The user cannot ActiveSync using the Four Slot Ethernet cradle. To ActiveSync with a host computer, use the Single Slot USB/Serial cradle, USB Charging cable or Serial Charging cable.

Accessories 2 - 9

Figure 2-7

Four Slot Ethernet Cradle

CRD5500-4000ER Setup

Connect the Four Slot Ethernet cradle to a power source and to an Ethernet switch, router, or hub, or a port on the host device.

2 - 10 MC67 Integrator Guide

Power Port

Ethernet Switch, Router, or Hub Connection

Ethernet 1Port

Ethernet 1 Port

Ethernet 2 Port

Right LED

Left LED

Figure 2-8

CRD5500-400ER Four Slot Ethernet Cradle Connection

Daisychaining Ethernet Cradles

Daisychain up to four Ethernet cradles to connect several cradles to an Ethernet network. Use either a straight or crossover cable. Daisy-chaining should not be attempted when the main Ethernet connection to the first cradle is 10 Mbps as throughput issues will almost certainly result.

To daisychain more than one Four Slot Ethernet cradle:

1. Connect power to each Four Slot Ethernet cradle.

2. Connect an Ethernet cable to the Ethernet 1 port of the first cradle and to the Ethernet switch. See Figure

2-8.

3. On the first Four Slot Ethernet cradle, connect a second Ethernet cable to the Ethernet 2 port. See Figure

2-9.

4. Connect the other end of the Ethernet cable to the Ethernet 1 port of the second Four Slot Ethernet cradle.

5. Connect additional cradles as described in step 3 and 4.

Figure 2-9

Daisychaining Four Slot Ethernet Cradles

Accessories 2 - 11

Power Port

Ethernet Switch, Router, or Hub Connection

Primary Port

LED Indicators (CRD5500-4000ER)

There are two LEDs on the front of the cradle and two on the Ethernet 2 port. The green Speed LED lights to indicate that the transfer rate is 100 Mbps. When the LED is not lit the transfer rate is 10 Mbps. The yellow Link LED blinks to indicate activity, or stays lit to indicate that a link is established. When it is not lit it indicates that there is no link.

Table 2-3

100 Mbps On On/Blink

10 Mbps Off On/Blink

CRD4000-4000ER LED Indicators

Data Rate Green Speed LED (Left) Yellow Link LED (Right)

CRD5501-4001ER Setup

Connect the Four Slot Ethernet cradle to a power source and to an Ethernet switch, router, or hub, or a port on the host device.

Figure 2-10

CRD5501-4001ER Four Slot Ethernet Cradle Connection

Daisychaining Ethernet Cradles

Daisychain up to four Four Slot Ethernet cradles to connect several cradles to an Ethernet network. Use either a straight or crossover cable. Daisy-chaining should not be attempted when the main Ethernet connection to the first cradle is 10 Mbps as throughput issues will almost certainly result.

To daisychain more than Four Slot Ethernet cradles:

1. Connect power to each Four Slot Ethernet cradle.

2. Connect an Ethernet cable to the Primary Port of the first cradle and to the Ethernet switch. See Figure

2-10.

2 - 12 MC67 Integrator Guide

To Switch

Secondary Port

Right LEDLeft LED

Primary PortTo Power Supply To Power Supply

3. On the first Four Slot Ethernet cradle, lift or remove the label flap and connect a second Ethernet cable to

the Secondary Port. See Figure 2-11.

4. Connect the other end of the Ethernet cable to the Primary Port of the second Four Slot Ethernet cradle.

5. Connect additional cradles as described in step 3 and 4.

Figure 2-11

Daisychaining Four Slot Ethernet Cradles

LED Indicators (CRD5501-4001ER)

There are two green LEDs on the front of the cradle and two green LED on the Primary port on the back of the cradle. These green LEDs light and blink to indicate the data transfer rate. When the LEDs are not lit the transfer rate is 10 Mbps.

Table 2-4

CRD5501-4001ER LED Indicators

Data Rate Left 1000 LED (Green) Right 100 LED (Green)

1 Gbps On/Blink Off

100 Mbps Off On/Blink

10 Mbps Off Off

Ethernet Cradle Drivers

The MC67 includes Ethernet cradle drivers that initiate automatically when you place the MC67 in a properly connected Four Slot Ethernet cradle. After inserting the MC67, configure the Ethernet connection:

1. Ta p > Settings > Connections tab >WiFi icon. The Configure Network Adapters window appears.

Accessories 2 - 13

Figure 2-12

2. In the My network card connects to: drop-down list, select the appropriate connection.

3. In the Tap an adapter to modify settings: list, select USB/Ethernet Series Adapter.

Figure 2-13

4. In the IP address window, select the appropriate radio button:

•

Configure Network Adapters Window

IP Address T ab

Use server-assigned IP address

•

Use specific IP address. Enter the IP address, Subnet mask, and Default gateway, as needed.

5. Ta p th e Name Servers tab.

2 - 14 MC67 Integrator Guide

Figure 2-14

6. Enter the appropriate DNS, Alt DNS, WINS, and Alt WINS server addresses.

7. Ta p ok.

Figure 2-15

8. Ta p ok to confirm the setup.

9. Ta p ok to exit.

Name Servers Tab

Adapters Dialog Box

Charging

Insert the MC67 into a slot to begin charging. The MC67’s charge LED shows the status of the battery charging

in the MC67. See Table 1-1 on pag e 1-6 for charging status indications. The 3600 mAh battery fully charges in

approximately six hours.

Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Charging is intelligently controlled by the MC67.

To accomplish this, for small periods of time, the MC67 alternately enables and disables battery charging to keep the battery at acceptable temperatures. The MC67 indicates when charging is disabled due to abnormal

temperatures via its LED. See Table 1-1 on page 1-6.

Four Slot Charge Only Cradle

This section describes how to set up and use a Four Slot Charge Only cradle with the MC67.

The Four Slot Charge Only cradle:

•

Provides 5.4 VDC power for operating the MC67.

•

Simultaneously charges up to four MC67s.

The user cannot ActiveSync using the Four Slot Charge Only cradle. To ActiveSync with a host computer, use the Single Slot USB cradle.

Setup

Connect the Four Slot Charge Only cradle to a power source.

Accessories 2 - 15

Figure 2-16

Four Slot Charge Only Cradle Connection

Charging Temperature

Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Charging is intelligently controlled by the MC67.

temperatures via its LED. See Table 1-1 on page 1-6.

2 - 16 MC67 Integrator Guide

Mounting Screw (4)

Mounting Tab (2)

Mounting Slot

Mounting Screw (2)

Four Slot

Cradle Bottom

Wall Mount Bracket

Use the optional Wall Mount Bracket to mount a four slot cradle to a wall. To attach the Wall Mount Bracket:

1. Use the Wall Mount Bracket as a template and mark the locations of the four mounting screws.

NOTE Use fasteners appropriate for the type of wall and the Wall Mount Bracket mounting slots. The Wall Mount

Bracket mounting slots are designed for a fastener with a #8 pan head. Fasteners must be able to hold a minimum of 4.9 Kg (10.8 lbs).

2. Mount the fasteners to the wall. The screw heads should protrude about a half of an inch from the wall.

3. Slip the Wall Mount Bracket over the screw heads and slide the bracket down over the screw heads.

4. Tighten the screws to secure the bracket to the wall.

Figure 2-17

Wall Mount Bracket

To mount a four slot cradle:

1. Screw the supplied screws into the bottom of the four slot cradle. The screw heads should protrude about

a quarter of an inch from the cradle.

Figure 2-18

2. Align the Wall Mount Bracket mounting tabs with the mounting slots in the back of the four slot cradle. Slip

Cradle Mounting Screws

the two mounting tabs into mounting slots.

Accessories 2 - 17

Wall Mount

Bracket

Screw Slots

Power Supply

Well

3. Swing the four slot cradle down onto the mounting bracket and align the mounting screws so that they fit

into the screw slots.

Figure 2-19

4. Tighten the mounting screws to secure the four slot cradle to the bracket.

Figure 2-20

5. Connect power (see Figure 2-16 on page 2-15). The power supply should be located in the power supply

Wall Mount Bracket

Mounting Screws

well.

2 - 18 MC67 Integrator Guide

Connector on Power Cable

VCD5500 Vehicle Cradle

This section describes how to set up and use a VCD5500 vehicle cradle with the MC67.

Once installed in a vehicle, the cradle:

•

holds the MC67 securely in place

•

provides power for operating the MC67

•

re-charges the battery in the MC67.

Requirements

For mounting:

•

four #8-32 self-locking nuts

•

four #8 washers

•

a drill with a #6 drill bit (.204”).

For power connection:

•

power input cable (optional), p/n 25-61987-01R or 25-128974-01R

•

UL Listed in-line fuse rated 250V, 5A (included), must be used if not connecting to vehicle’s fuse panel

•

in-line fuse holder (included), must be used if not connecting to vehicle’s fuse panel.

Connector Pin-Outs

Table 2-5

1 Chassis ground (Black Wire)

2 Chassis ground (Bare Wire)

3 V+ (Red Wire)

4 V+ (Red Wire)

Power Input Cable

Pin Signal

CAUTION ROAD SAFETY - Do not use the MC67 while driving. Park the vehicle first. Always ensure the

MC67 is fully inserted into the cradle. Do not place it on the seat or where it can break loose in a collision or sudden stop. Lack of proper insertion may result in property damage or personal injury. Zebra is not responsible for any loss resulting from the use of the products while driving. Remember: Safety comes first.

Mounting the Cradle

CAUTION Only mount the Vehicle Cradle in a vertical position with the release level at the top or in a horizontal

position with the MC67 display facing up. Never mount the vehicle cradle on the side or upside down or on a wall that can be subject to impact or collision of greater than 40Gs, in accordance with SAE J1455 Section 4.10.3.5

Accessories 2 - 19

1.5”

1.2”

1. Select a mounting location for the cradle. It should be flat, and must provide adequate support for the

cradle.

NOTE If using the GPS functionality of the MC67, ensure that the vehicle cradle is positioned so that the MC67

has a clear unobstructed view of the sky.

2. Prepare the mounting surface to accept four #8-32 studs, using the mounting template below. Drill four

holes with a #6 drill bit.

Figure 2-21

3. Position the cradle on the mounting surface.

4. Fasten it using four #8 washers and four #8-32 self-locking nuts.

CAUTION Do not install a VCD5500 Vehicle Cradle on or near an air bag cover plate or within an aerobic zone.

Power Connection

Please read all of the following instructions before beginning.

WARNING! A properly trained technician must perform the power connection. Improper connection can

To connect the cradle to power:

CAUTION When setting up connection for this cradle, only use the power input cable, part number 25-61987-01R

1. Locate the vehicle power source.

Vehicle Cradle Mounting Template

Also, do not install it in a location that affects vehicle safety or driveability.

damage your vehicle, cradle or MC67. Refer to the vehicle’s Owner’s Manual for instructions for removing power.

or 25-128974-01R.

2 - 20 MC67 Integrator Guide

Shield Wire

(bare wire)

Ground

Wire (black)

V+ Power (red)

5A Fuse and

Fuse Holder

NOTE The ideal location for connecting the vehicle cradle power input cable would be an accessory output in

your vehicle’s fuse panel. The vehicle cradle should be added to a circuit with a maximum load capacity

for the cradle and the original circuit. Refer to the vehicle’s Owner’s Manual for identification of the circuit.

If a fused output is not available, the vehicle cradle must be installed with the provided in-line fuse holder and UL Listed 5A fuse. The fuse protects the vehicle from an electrical short on the power line to the cradle. To use the cradle to charge the MC67 and spare battery, when the vehicle’s ignition is off, connect the cradle to unswitched power.

2. Route the power input cable from the cradle’s power port to the connection point for the vehicle’s power

source.

CAUTION The means of routing and securing the power input cable from the cradle through to the vehicle power

source is extremely important. Hazards associated with improper wiring can be severe. To avoid unintentional contact between the wire and any sharp edges, provide the cable with proper bushings and clamping where it passes through openings. If the wire is subjected to sharp surfaces and excess engine vibration, the wiring harness insulation can wear away, causing a short between the bare wire and chassis. This can start a fire. To avoid any mishaps, all wiring should be routed away from moving parts, high temperature areas and any contaminants.

3. When using the supplied in-line fuse holder (which must be used if not connecting to vehicle’s fuse panel):

a. Ensure the fuse holder contains a 5A UL Listed slow-blow fuse.

b. Splice the fuse holder to the end of the red V+ wire, as shown above. Make the distance from the fuse

to the power connection point as short as possible.

Figure 2-22

Vehicle Cradle Power Connection

4. Prepare the cable termination.

a. Red wire: connect to a +12/24 V vehicle power source.

b. Black wire and Shield wire: connect to vehicle ground wire or chassis ground.

Accessories 2 - 21

Release Lever

NOTE How the cable terminates depends on the vehicle. If the vehicle has a power output connector, then you

must attach a mating connector to the end of the power cable. You may be able to connect to a fuse panel

with a simple blade terminal or commercially available connector. Consult the vehicle Owner’s Manual for

information on how to access the power supply in the vehicle.

5. Connect the power input cable into the power port on the cradle.

To see if the cradle has power, insert the MC67. The Charging LED on the MC67 blinks slowly to indicate

charging and turns solid amber when the battery is completely charged. See Table 1-1 on page 1-6 for other

indications.

Charging the MC67 Battery

Insert the MC67 into the vehicle cradle to begin charging. A click indicates that the MC67 button release locking mechanism is enabled and the MC67 is locked in place.

Figure 2-23

MC67 Battery Charging

CAUTION Ensure the MC67 is fully inserted in the cradle. Lack of proper insertion may result in property damage

or personal injury. Zebra, Inc. is not responsible for any loss resulting from the use of the products while driving.

Removing the MC67

To remove the MC67, press the release levers on the cradle and pull the MC67 up and out of the cradle.

2 - 22 MC67 Integrator Guide

Release Lever

Figure 2-24

Removing the MC67

Battery Charging Indicators

The MC67’s charge LED indicates the status of the battery charging in the MC67. See Table 1-1 on page 1-6

for charging status indications.

The 3600 mAh battery charges in approximately six hours.

Charging Temperature

Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Charging is intelligently controlled by the MC67.

temperatures via its LED. See Table 1-1 on page 1-6.

Four Slot Battery Charger

Battery Charging

LEDs (4)

Battery

This section describes how to use the Four Slot Battery Charger to charge up to four MC67 spare batteries.

Spare Battery Charging

1. Connect the charger to a power source.

2. Insert the spare battery into a spare battery charging well and gently press down on the battery to ensure

proper contact.

Accessories 2 - 23

Battery Charging Indicators

Figure 2-25

An amber LED is provided for each battery charging well. See Table 2-6 for charging status indications. The

3600 mAh battery charges in approximately six hours.

Four Slot Spare Battery Charger

Charging Temperature

Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Charging is intelligently controlled by the charger in order to ensure safe operation and optimize long-term battery life.

To accomplish this, for small periods of time, the charger alternately enables and disables battery charging to keep the battery at acceptable temperatures. The charger indicates when charging is disabled due to abnormal

temperatures via its LED. See Table 2-6.

2 - 24 MC67 Integrator Guide

Table 2-6

Off No spare battery in slot; spare battery not placed correctly; cradle is not powered.

Fast Blinking Amber Error in charging; check placement of spare battery.

Slow Blinking Amber Spare battery is charging.

Solid Amber Charging complete.

Spare Battery LED Charging Indicators

LED Indication

Cables

This section describes how to set up and use the cables. The cables are available with a variety of connection capabilities.

The following communication/charge cables are available:

•

USB Charging cable

•

Charge Only cable

•

Auto Charge cable

•

DEX cable.

USB Charging Cable

The USB Charging cable provides the MC67 with operating and charging power when used with the Zebra approved power supply and AC line cord and synchronize information between the MC67 and a host computer.

Accessories 2 - 25

Figure 2-26

USB Charging Cable

Charge Only Cable

The Charge Only cable provide the MC67 with operating and charging power when used with the Zebra approved power supply.

2 - 26 MC67 Integrator Guide

Figure 2-27

Charge Only Cable

Auto Charge Cable

The Auto Charge cable plugs into a vehicle cigarette lighter and provide the MC67 with operating and charging power.

Figure 2-28

Auto Charge Cable

Connecting to the MC67

1. If required, connect the cable power input connector to the Zebra approved power source.

2. Slide the bottom of the MC67 into the connector cup end of the cable until the MC67 is firmly seated in the

cup.

3. Slide the two locking tabs up until they both lock into position.

Accessories 2 - 27

Locking Tab

Figure 2-29

4. To remove, slide the two locking tab down and remove the cable from the MC67.

Cable Cup Locking Tabs

Battery Charging Indicators

The MC67 amber Charge LED indicates the MC67 battery charging status. The 3600 mAh battery charges in

less than six hours. See Table 1-1 on page 1-6 for charging status indications.

Charging Temperature

Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Charging is intelligently controlled by the MC67.

temperatures via its LED. See Table 1-1 on page 1-6.

2 - 28 MC67 Integrator Guide

Vehicle Holder

WARNING! Some countries prohibit the mounting of any electronic device in any location on the vehicle

dashboard and windshield. Be sure to check your local laws acceptable mounting areas before installing the auto mounting kit.

Installation Reminders

Figure 2-30

•

Vehicle Holder Mounting

Do not mount the vehicle holder where it will obscure the driver’s view of the road.

Do not mount the vehicle holder near the driver seat air bag deployment area.

Do not place the MC67 on top of the dashboard or anywhere without securing it in the vehicle holder.

Do not mount the vehicle holder near the passenger seat air bag deployment area.

Install the vehicle holder on the surface of your vehicle that is reasonably flat and free of dirt and oil.

Device Mounting Precautions

•

Some countries prohibit the mounting of any electronic device in any location on the vehicle dashboard. Be sure to check your local laws acceptable mounting areas before installing the vehicle holder.

•

The heating and cooling cycle of a vehicle’s interior will in some cases loosen the adhesion of the suction cup. Check the vacuum seal of the vehicle mount kit for adequate adhesion each time you use the unit, and reinstall if necessary.

•

If the vehicle holder has problems staying on, clean the plastic suction cup with alcohol, then reinstall.

Installation

Install the vehicle mount on the surface of your vehicle that is reasonably flat and free of dirt and oil. Clean the mounting surface with a glass cleaner and a clean cotton cloth. Install the vehicle mount on the windshield or other flat car surface using the supplied mounting disc.

Assembly

Cradle Plate

Cradle

Suction Cup Mount

1. Insert the vehicle holder’s cradle plate to the holes on the back of the cradle.

2. Push the cradle down until both parts are engaged.

Windshield Installation

1. Fix the suction cup mount to the selected area with the suction lever facing up.

Accessories 2 - 29

Figure 2-31

2. Flip the lever down to create a vacuum between the suction cup and the mounting surface.

3. Make sure that the suction bond is strong enough before proceeding to the next step.

4. Slide the MC67 into the cradle.

Windshield Installation

2 - 30 MC67 Integrator Guide

Locking Tab

Figure 2-32

5. Connect the auto charger cable to the MC67 and slide the two locking tabs up to secure the cable cup to

Insert MC67 into Vehicle Holder

the MC67.

6. Connect the other end to the cigarette lighter socket.

The LED indicator on the right side of the touch screen lights up orange during charging.

NOTE Prior to removing the MC67 from the vehicle holder, disconnect the auto-charge cable from the MC67.

Flat Surface Installation

1. Remove the plastic sheet on the bottom of the mounting disc.

2. Place the disc, sticky side down, on a clean flat surface.

Figure 2-33

Mounting Disc

3. Fix the suction cup mount to the disc with the suction lever facing up.

4. Flip the lever down to create a vacuum between the suction cup and the disc.

5. Make sure that the suction bond is strong enough before proceeding to the next step.

6. Slide the MC67 into the cradle.

Accessories 2 - 31

Figure 2-34

7. Connect the auto charger cable to the MC67 and slide the two locking tabs up to secure the cable cup to

Vehicle Holder Mounted on Flat Surface

the MC67.

8. Connect the other end to the cigarette lighter socket.

The LED indicator on the right side of the touch screen lights up orange during charging.

2 - 32 MC67 Integrator Guide

Handstrap Replacement

Removal

To remove a handstrap from the MC67:

CAUTION Close all running applications prior to replacing the handstrap. The backup battery maintains data for

up to 15 minutes. If replacement takes longer than 15 minutes data may be lost.

1. If the MC67 is in suspend mode, press the red Power button to wake the MC67.

2. Press the red Power button. The Power Action Key window appears.

3. Ta p Safe Battery Swap. The Data Capture LED lights red.

4. When the LED turns off, remove the handstrap.

Figure 2-35

5. Remove the battery.

6. Using a small flat screwdriver, push the head of the screwdriver between the handstrap pin and the bottom

Handstrap Clip Removal

CAUTION When removing handstrap pin, be careful not to damage handstrap mounting area.

of the housing as shown below.

7. Pry the handstrap and pin up and out of the handstrap mount area.

Accessories 2 - 33

Figure 2-36

8. Repeat for the other side of the handstrap.

9. Remove pin from the handstrap.

Handstrap and Pin Removal

Figure 2-37

10. Pull handstrap through handstrap slot.

Installation

To install a new handstrap:

1. Feed bottom end of handstrap into handstrap slot on the bottom of the MC67.

Pin Removal

2 - 34 MC67 Integrator Guide

Figure 2-38

2. Slide pin into bottom of handstrap.

3. Center the pin in the handstrap loop.

4. Pull handstrap so that the pin and bottom of handstrap slide into position in the mounting area.

Figure 2-39

Feed handstrap into Handstrap Slot

NOTE Handstrap and pin should fit securely into the handstrap mounting area. When pulling on handstrap use

enough force to engage pin into place.

Pin and Handstrap in Mounting Area

Figure 2-40

5. Slide tether loop over handstrap.

6. Insert the handstrap clip into the slot on the device. Ensure that it is securely in place.

Slide Handstrap and Tether Over Handstrap Mount

Chapter 3 Synchronization

Introduction

Synchronization lets the user manage information between an MC67 and a host computer so that changes made either on the MC67 or on the host computer appear in both places. Download and install sync software to the host computer (either Microsoft ActiveSync for Windows XP or Windows Mobile Device Center (WMDC) for Windows Vista and Windows 7) in order to use the sync feature. Visit www.microsoft.com on the host computer for details.

NOTE When the MC67 is connected to a host computer and a sync connection is made, the Wi-Fi radio is disabled.

This is a Microsoft security feature to prevent connection to two networks at the same time.

The sync software:

•

Allows working with MC67-compatible applications on the host computer. The sync software replicates data from the MC67 to view, enter, and modify data on the host computer.

•

Synchronizes files between the MC67 and the host computer, converting the files to the correct format.

•

Backs up the data stored on the MC67. Synchronization is a one-step procedure that ensures the data is always safe and up-to-date.

•

Copies (rather than synchronizes) files between the MC67 and the host computer.

•

Controls when synchronization occurs by selecting a synchronization mode. For example, synchronize continuously while the MC67 is connected to the host computer, or synchronize only on command.

•

Selects the types of information to synchronize and control how much data is synchronized.

Installing the Sync Software

To download and install either Microsoft ActiveSync (for Windows XP) or WMDC (for Windows Vista and Windows

7), visit www.microsoft.com and follow the instructions for the host computer.

MC67 Setup

NOTE Microsoft recommends installing the sync software on the host computer before connecting the MC67.

3 - 2 MC67 Integrator Guide

The MC67 can be set up to communicate with a USB connection. The MC67 communication settings must be set to match the communication settings used with ActiveSync or WMDC.

1. On the MC67 tap > Programs > ActiveSync icon. The ActiveSync window appears.

2. Ta p Menu > Connections.

3. Select the connection type from the drop-down list.

4. Ta p OK to exit the Connections window and tap OK to exit the ActiveSync window.

5. Proceed with installing ActiveSync or WMDC on the host computer and setting up a partnership.

Setting Up a Sync Connection

ActiveSync

1. Select Start > Programs > Microsoft ActiveSync on the host computer. The ActiveSync Window displays.

Figure 3-1

2. In the ActiveSync window, select File > Connection Settings. The Connection Settings window appears.

Figure 3-2

ActiveSync Window

NOTE Assign each MC67 a unique device name. Do not try to synchronize more than one MC67 to the same name.

Connection Settings Window

3. Select Allow USB connections check box.

4. Select the Show status icon in taskbar check box.

5. Select OK to save any changes made.

Windows Mobile Device Center

1. Select Start > All Programs > Windows Mobile Device Center on the host computer.

Synchronization 3 - 3

Figure 3-3

2. In the WMDC window, under Mobile Device Settings, click Connection settings.

Figure 3-4

3. Select Allow USB connections and adjust any additional settings as needed.

4. Click OK to save your settings.

Windows Mobile Device Center Window

Connection Settings Window

Synchronization

NOTE When the MC67 is connected to your computer and a sync connection is made, the Wi-Fi radio (if applicable)

is disabled. This is a Microsoft security feature to prevent connection to two networks at the same time.

To synchronize with the MC67:

1. Connect the MC67 to your computer using the provided USB cable.

2. If the Get Connected window does not appear on your computer, select Start > All Programs > Microsoft

ActiveSync or Windows Mobile Device Center.

3. Click Next.

4. Select the check box to synchronize with a server running Microsoft Exchange if applicable.

3 - 4 MC67 Integrator Guide

ActiveSync WMDC

5. Click Next.

Figure 3-5

6. Select the appropriate settings and click Next.

Figure 3-6

7. Click Finish.

Select Synchronization Settings

Setup Complete Window

Synchronization 3 - 5

ActiveSync WMDC

Figure 3-7

Connected Window

During the first synchronization, information stored on the MC67 is copied to the host computer. When the copy is complete and all data is synchronized, the MC67 can be disconnected from the host computer.

NOTE The first synchronization operation must be performed with a local direct connection. Windows Mobile retains

partnerships information after a cold boot.

3 - 6 MC67 Integrator Guide

CHAPTER 4 WAN GSM CONFIGURATION

Introduction

This chapter explains how to verify MC67 service on an Global System for Mobile communications (GSM) wireless network and establish settings.

GSM networks deliver mobile voice and data services, such as Short Message Service (SMS)/Text Messaging, with full roaming capabilities across the world. High-speed Packet Access + (HSPA+) enabled networks offer Internet-based content and packet-based data services. This enables services such as internet browsing, e-mail on the move, powerful visual communications, multimedia messages, and location-based services.

When using the MC67 as a phone, services can include speed dialing, call tracking, voice mail, call forwarding, conference calling, and caller ID, depending on the type of service.

Also use the integrated phone as a modem to connect the MC67 to an ISP or work network. The GSM enabled MC67 can connect to the Internet or work network using Cellular Line, or using the modem specified by the mobile phone service provider.

NOTE Before using an MC67 on a wireless network, first select a provider, establish a voice and data-enabled

service plan, and configure the MC67 (where applicable). Refer to the MC67 User Guide for information

on how to use the phone and services.

MC67 Service Verification

MC67 phone and data services require a live SIM card, obtained from a service provider, installed in the MC67. The SIM card has embedded circuitry on one side of its surface which, when inserted into an MC67, provides phone service. The SIM card provides a phone number, determines the features or services available to the subscriber and identifies the subscriber to the network.

With most SIM card, the MC67 automatically configures the data connection, otherwise it is required to manually configure the data connection before using.

Ensuring Network Coverage

To ensure network coverage:

4 - 2 MC67 Integrator Guide

1. Ensure an activated SIM card, from the phone service provider, is installed in the MC67.

NOTE The SIM card must be enabled to connect to the network.

2. Verify active phone and data services by tapping the Status bar and then to display the Phone dialog.

The Carrier name appears in the dialog box.

Figure 4-1

3. Verify SIM card functionality:

a. Ta p > Settings > Personal > Phone > Network.

Figure 4-2

b. Ensure the service provider’s network appears in the Current network: field.

c. If the network does not appear, tap Find Network. If the network still does not appear, verify that the

Connectivity Dialog

Phone Settings - Network

SIM card was installed correctly. If it was, and no network appears, contact the service provider.

Manually Configuring a Data Connection

If a data connection is not automatically configured, manually configure the data connection:

1. Acquire an Access Point Name (APN) from the service provider.

2. Ta p > Settings > Connections > Connections > Tasks.

WAN GSM Configuration 4 - 3

Figure 4-3

3. Under My ISP select Add a new modem connection.

Figure 4-4

4. Enter a connection name in the Enter a name for the connection: text box.

5. Select Cellular Line (GPRS) from the Select a modem: drop-down list.

6. Ta p Next.

Connections Window

Connections Window - Make New Connection

Figure 4-5

7. Enter the APN from the service provider in the Access point name: text box.

8. Ta p Next.

Connections Window - Access Point Name

4 - 4 MC67 Integrator Guide

Figure 4-6

9. Enter a username in the User name text box, if required by the service provider.

10. Enter a password in the Password text box, if required by the service provider.

11. Enter a domain name in the Domain text box, if required by the service provider.

12. Ta p Finish.

13. Ta p OK to exit Connections.

Connections Window - User Name & Password

Establishing a Data Connection

To establish a data connection:

1. Ensure a SIM card is installed in the MC67.

2. Configure a data connection. See Manually Configuring a Data Connection on page 4-2.

3. Tap the Status bar and then .

Figure 4-7

4. Ta p Settings.

5. Ta p Managing existing connections.

6. Tap and hold on the data connection until a menu appears.

Connectivity Dialog Box

WAN GSM Configuration 4 - 5

Figure 4-8

7. Select Connect.

Figure 4-9

8. When a connection is established, launch Internet Explorer to browse the Internet or launch an applicable

application.

Data Connection

Connecting Using GPRS

Ending a Data Connection

To end a data connection:

1. Tap the Status Bar and then to display the Connectivity dialog box.

4 - 6 MC67 Integrator Guide

Figure 4-10

2. Ta p Disconnect.

Connectivity Dialog Box

NOTE Tapping Disconnect during an active data transfer (e.g., downloading a web page) automatically

reconnects the connection. You cannot disconnect the connection until the data transfer is complete

MC67 Settings

Use the Phone Settings window to customize settings, such as the ring type and ring tone for incoming calls,

security options, and other options depending on the type of service.

Sounds

Use the Sounds tab to customize ring type, ring tone, keypad tone, and security options.

Ta p > Settings > Personal > Phone or tap > Phone > Menu > Options.

WAN GSM Configuration 4 - 7

Figure 4-11

•

Select Short tones or Long tones to specify the duration of the sound when you press a number on the keypad. Select Off to disable tones.

Security

Phone - Sounds

Phone Number automatically displays on the when a live SIM card is installed.

Select a ring type from the Ring type: drop-down list. The ring type changes the way the MC67 rings when you receive an incoming call. Regardless of the ring type selected, a dialog box appears on the MC67’s display for incoming calls.

Select a ring tone for incoming calls from the Ring tone: drop-down list. To hear a sample of the selected

ring tone, tap . Tap to end the ring tone.

NOTE To use custom .wav, .mid, or .wma files as ring tones, use ActiveSync on the host computer to copy the

file to the /Windows/Rings folder on the MC67. Then select the sound from the ring tone list

Select a keypad tone from the Keypad: drop-down list. This selection determines the tone that sounds when entering a phone number on the keypad.

NOTE Turning off sounds saves power and prolongs battery life.

Enabling a PIN

NOTE Place emergency calls at any time, without requiring a PIN or a SIM card.

4 - 8 MC67 Integrator Guide

To require a PIN when using the phone:

1. From the Security tab (Figure 4-11), select the Require PIN when phone is used check box.

Figure 4-12

2. Use the touch keypad to enter a four to eight digit PIN.

3. Ta p Enter to enable the PIN and return to the Phone tab.

Enter PIN

Changing a PIN

CAUTION If the user enters an incorrect PIN, the message “SIM PIN incorrect: Try again” appears. After three

consecutive incorrect attempts, the SIM card is blocked. The MC67 does not allow the user to attempt to enter your PIN again and the user must obtain a PIN Unblock Key from the service provider.

1. From the Security tab (Figure 4-11), tap Change PIN.

2. Use the touch keypad to enter the current PIN.

3. Ta p Enter.

4. Use the touch keypad to enter a new four to eight digit PIN.

5. Ta p Enter.

6. Reenter the new PIN for confirmation and tap Enter.

7. Ta p OK to confirm the change.

Disabling a PIN

1. From the Security tab (Figure 4-11), deselect the Require PIN when phone is used check box.

2. Use the touch keypad to enter the current PIN.

3. Ta p Enter.

4. Ta p OK to confirm the change.

5. Ta p OK to exit settings.

WAN GSM Configuration 4 - 9

Services

Use the Services tab to configure settings for subscribed phone services. For example, block certain types of incoming and/or outgoing calls, disclose the caller’s identity when making outgoing calls, forward incoming calls to a different phone number, receive notification of incoming calls when a phone session is in use and set up voice mail and short message service.

1. Ta p > Settings > Personal > Phone > Services or tap > Phone > Menu > Options > Services.

Figure 4-13

2. Select a service from the list and tap Get Settings... .

3. Change services settings as follows.

Phone - Services

Call Barring (Call Blocking)

Use call barring to block certain types of incoming and/or outgoing calls. Select the type of incoming and/or outgoing calls to block.

Figure 4-14

Call Barring/Call Blocking

Caller ID

Enable caller ID to reveal the identity of the person making an outgoing call. Select the Everyone radio button to always display the caller ID. Select the No one radio button to prevent the caller’s identity from appearing to others.

4 - 10 MC67 Integrator Guide

Figure 4-15

Caller ID

Call Forwarding

NOTE Call Forwarding may not be available on all networks. Check with your service provider for availability.

Use call forwarding to forward incoming calls to a different phone number.

•

To forward all calls to a different phone number:

• select the Forward all incoming phone calls check box.

• enter the phone number to receive forwarded calls in the To: text box.

•

To forward incoming calls to a different phone number based on a specific situation, select one or more of the check boxes under Forward phone calls only if:.

• No answer: enter the phone number to receive forwarded calls only when the phone cannot be answered. Then select a time period from the Forward after: drop-down list. Options are 5, 10, 15, 20, 25 and 30 seconds.

• Unavailable: enter the phone number to receive forwarded calls only when the phone is turned off or the user is unreachable.

•Busy: enter the phone number to receive forwarded calls only when the line is busy.

Figure 4-16

Call Forwarding

WAN GSM Configuration 4 - 11

Call Waiting

NOTE Call Waiting may not be available on all networks. Check with your service provider for availability.

Call waiting notifies you of an incoming call when the phone is in a phone session. Select the Notify me radio

button to enable call waiting. Select the Do not notify me radio button to disable call waiting.

Figure 4-17

Call Waiting

Voice Mail and Text Messages

To use voice mail and send short messages, enter the voice mail and/or text message phone number in the appropriate text boxes.

Figure 4-18

Voice Mail and Text Messages

Fixed Dialing

Use Fixed Dialing to restrict the phone to dial only the phone number(s) or area code(s) specified in a Fixed Dialing list.

1. Select Fixed Dialing and tap Get Settings.

4 - 12 MC67 Integrator Guide

Figure 4-19

2. Select the Enable fixed dialing check box.

3. To add a number to the list, tap Menu > Add.

4. Enter the phone number or area code to restrict and tap Done.

5. Repeat steps 3 and 4 to add more numbers, and tap Done twice when complete.

6. Enter PIN2 and tap Done.

Fixed Dialing Window

Network

Use the Network tab to view available networks, determine the order in which the phone accesses another network if the current network is unavailable, and specify whether to change networks manually or automatically. The current network remains active until it’s changed, the signal is lost, or the SIM card is changed.

The network the MC67 currently uses appears in the Current network: field at the top of the window.

Changing Networks Manually

1. Ta p > Settings > Personal > Phone > Network or tap > Phone > Menu > Options > Network.

Figure 4-20

2. From the Network selection drop-down list, select Manual.

Phone - Network

WAN GSM Configuration 4 - 13

Figure 4-21

3. From the Choose Network window, select the network to use.

4. Ta p OK.

Choose Network

Viewing Available Networks

To view all wireless networks available:

1. Ta p > Settings > Personal > Phone > Network or tap > Phone > Options > Network.

Figure 4-22

2. Ta p Find Network.

Figure 4-23

3. From the Choose Network window, select the network to use.

4. Ta p OK.

Phone - Network

Choose Network

Setting Preferred Networks

Set networks in a preferred order of access. Setting preferred networks allows the MC67 to access a second preferred network if the first is unavailable.

4 - 14 MC67 Integrator Guide

1. Ta p > Settings > Personal > Phone > Network or tap > Phone > Menu > Options > Network.

Figure 4-24

2. Ta p Set Networks to view all available networks.

Figure 4-25

3. Select the preferred networks by tapping one or more check boxes.

4. Ta p Move Up and Move Down, as necessary, to place the selected networks in the preferred order.

5. Ta p OK to send the new settings to the network.

6. From the Network tab, select Automatic from the Network selection drop-down list.

Phone - Network

Preferred Networks

7. Ta p OK to exit settings.

Phone Info

Use the Phone Info tab to view hardware and software information about the phone.

1. Ta p > Settings > Personal folder > Phone icon > Phone Info tab

> Phone > Menu > Options > Phone Info tab.

WAN GSM Configuration 4 - 15

Figure 4-26

2. Ta p OK to exit settings.

Phone - Phone Info

Network Time Synchronization

The MC67 can be configured to synchronize the clock with the time from the carrier network. A registry key on the MC67 has to be created to enable this feature.

Using a registry editor, navigate to the following:

[HKEY_LOCAL_MACHINE\SOFTWARE\Symbol\RIL\RHA\PH8]

Create the following key:

“SyncSystemTime”=dword:00000001

where:

dword:0 = disabled

dword:1 = enabled

After setting the registry key, warm boot the MC67.

Enhanced Operator Name String

The MC67 is enabled to download and display the name of the GSM network currently logged in to. Two registry keys on the MC67 have to be edited to disable this feature.

Using a registry editor, navigate to each of the following:

[HKEY_LOCAL_MACHINE\Software\Microsoft\RIL]

Edit the following key:

“EonsEnable”=dword:1

[HKEY_LOCAL_MACHINE\Comm\Cellular\Ril]

Edit the following key:

“EONSEnable”=dword:1

4 - 16 MC67 Integrator Guide

where:

dword:0 = disabled

dword:1 = enabled (default)

After setting the registry key, warm boot the MC67.

Service Provider Name Display

The reg key (“UseServiceProviderName”) originally was used to fix the dual-line SIM card issue with value 2. But for the Italian Post, the value 1 should be used to show the virtual carrier name (Poste Mobile).

[HKEY_LOCAL_MACHINE\Software\Microsoft\RIL]

“UseServiceProviderName”=dword:1

where:

dword:0 = Display network provider name

dword:1 - Display service provider name (default)

dword:2 - Display both network provider and service provider name

CHAPTER 5 WAN CDMA CONFIGURATION

Introduction

This chapter explains how to configure an MC67ND on a Code Division Multiple Access (CDMA) wireless network.

CDMA is a form of wireless multiplexing in which data (e.g., Short Message Service) can be sent over multiple frequencies simultaneously, optimizing the use of available bandwidth. In an CDMA system data is broken into packets, each of which are given a unique identifier, so that they can be sent out over multiple frequencies and then re-built in the correct order by the receiver.

When using the MC67ND as a phone, services can include speed dialing, call tracking, voice mail, call forwarding, conference calling and caller ID, depending on the type of service.

The integrated phone in the MC67ND can also be used as a modem to connect the MC67ND to an ISP or work network. The MC67ND can connect to the Internet or work network using Cellular Line, or using the modem specified by the mobile phone service provider.

NOTE Before the MC67ND can be used on a CDMA wireless network, a provider must be selected, a voice and

data-enabled service plan must be established and the MC67ND must be properly configured (where applicable).

Refer to the MC67ND User Guide for information on how to use the phone and services.

CDMA Phone Activation

To activate the MC67ND on a CDMA network, see Network Activation on page 1-7.

Activation Test

To test the service.

1. Ta p Start > Phone.

5 - 2 MC67 Integrator Guide

Figure 5-1

2. Ensure the carrier name displays on the window.

3. Make a voice call to ensure activation was successful.

Phone Window - Example

NOTE If activation was not successful, contact the service provider.

Establishing a Data Connection

NOTE Ensure that you have data service activated with your service provider.

A data connection allows Internet access across a wireless network. Data connection is pre-packaged with service accounts.

To verify active data service:

1. Ta p Start > Internet Explorer.

2. In the address bar, enter a URL for a web site.

3. Tap Status bar and then tap to display the Connectivity dialog. The dialog box displays the data

connection information.

Figure 5-2

Data Connection

CDMA Settings

Use the Phone Settings window to customize CDMA phone settings, such as the ring type and ring tone for

incoming calls and other options depending on the type of service.

Phone

Use the Phone tab to customize ring type, ring tone and keypad tone when entering phone numbers.

1. Ta p Start > Settings > Personal > Phone.

WAN CDMA Configuration 5 - 3

Figure 5-3

2. Select a ring type from the Ring type: drop-down list. The ring type changes the way the MC67ND rings to

notify the user of an incoming call. Regardless of the ring type selected, a dialog box appears on the display for incoming calls.

3. Select a ring tone for incoming calls from the Ring tone: drop-down list. To hear a sample of the selected

ring tone, tap . Tap to end the ring tone.

4. Select a keypad tone from the Keypad: drop-down list. This selection determines the tone that sounds

when entering a phone number on the keypad.

a. Select Short Tones for a tone that sounds only for one or two seconds.

b. Select Long Tones for a continuous sound for as long as the number on the keypad is pressed.

c. Select Off to disable tones.

5. Select the Notify me when voice privacy is unavailable check box to receive a message when dialing.

6. Ta p OK to exit settings.

Phone Window - Phone Tab

NOTE To use custom .wav, .mid or .wma files as ring tones, use ActiveSync on the host computer to copy the file

to the /Windows/Rings folder on the MC67ND. Then, select the sound from the ring tone list.

NOTE Turning off sounds saves power and prolongs battery life.

Phone Information

Use the Phone Info tab to view phone number and version information.

5 - 4 MC67 Integrator Guide

1. Ta p Start > Settings > Personal folder > Phone icon > Phone Info tab.

Figure 5-4

2. Ta p OK to exit settings.

Phone Window - Phone Info Tab

Services

Depending on the type of subscribed phone services, the following services may be available: call barring, caller ID, call forwarding, call waiting, voice mail and Short Message Service (SMS).

Call Barring (Call Blocking)

Call barring blocks certain types of incoming and/or outgoing calls. This service is setup when an account is opened with the service provider.

Caller ID

Caller ID provides a way for people to know the identity of the person making an outgoing call. To disable caller ID and block the outgoing phone number:

1. Enter *67 on the phone keypad.

2. Enter the phone number to call.

NOTE *67, followed by the phone number, must be entered on a call-by-call basis to block the outgoing phone

number.

Call Forwarding

NOTE Call Forwarding may not be available on all networks. Check with your service provider for availability.

Use call forwarding to forward incoming calls to a different phone number. To enable call forwarding and send calls to another phone number:

1. Enter *72 on the phone keypad.

2. Enter the area code and phone number of the phone to accept the forwarded calls.

3. Ta p Tal k .

4. A beep sounds indicating activation.

WAN CDMA Configuration 5 - 5

5. Ta p End.

To disable call forwarding:

1. Enter *73 on the phone keypad.

2. Ta p Tal k .

3. A beep sounds indicating deactivation.

4. Ta p End.

Call Waiting

NOTE Call Waiting may not be available on all networks. Check with your service provider for availability.

Call waiting notifies the user of an incoming call when the phone is in a phone session. This service is setup when an account is opened with the service provider.

Voice Mail and Short Message Service (SMS)

This service is setup when an account is opened with the service provider.

Network Time Synchronization

The MC67ND can be configured to synchronize the clock with the time from the carrier network. A registry key on the MC67ND has to be created to enable this feature.

Using a registry editor, navigate to the following:

[HKEY_LOCAL_MACHINE\SOFTWARE\Symbol\RIL\RHA\PH8]

Create the following key:

“SyncSystemTime”=dword:00000001

where:

dword:0 = disabled

dword:1 = enabled

After setting the registry key, warm boot the MC67ND.

5 - 6 MC67 Integrator Guide

CHAPTER 6 APPLICATION DEPLOYMENT

Introduction

This chapter describes features in Windows Mobile including new security features, how to package applications, and procedures for deploying applications onto the MC67.

Security

The MC67 implements a set of security policies that determine whether an application is allowed to run and, if allowed, with what level of trust. To develop an application, you must know the security configuration of the device, and how to sign an application with the appropriate certificate to allow the application to run (and to run with the needed level of trust).

Application Security

Application security controls the applications that can run on the MC67.

•

Trusted - All applications must be digitally signed by a certificate on the MC67.

•

Prompted - User is prompted to allow unsigned applications to run.

•

Open - All applications run.

Developers can include their own certificates and provision the device to “trusted.”

Digital Signatures

Digital signatures provide a way to authenticate the author of EXEs, DLLs, and packages. Digitally signed applications give users confidence that an application comes from where they think it comes from. For example, if an end-user downloads an update package from the internet that is digitally signed with Zebra's software certificate, they are assured that the package is authentic and that it was created by Zebra. By enforcing the use of digital signatures, users can also prevent malicious applications from executing on the MC67. For example, users can provision the MC67 to only execute “trusted” applications (digitally signed).

Zebra ships all Windows Mobile 6 based products in an “open” state, which means all signed and unsigned applications should work. However, customers can still reconfigure their MC67 to operate in the “trusted”

6 - 2 MC67 Integrator Guide

mode. This means that only applications signed with a certificate from the Privileged Execution Trust Certificate Store can run.

To support the broadest number of deployments, third-party software developers should perform the following when releasing software for a Windows Mobile 6 devices:

•

Sign all their EXEs & DLLs with their private key

•

Provide the corresponding public certificate to end-users so that it can be installed into Privileged Execution Trust Certificate Store.

If the software is installed via a .CAB file, developer should also:

•

Sign the .CAB file with their private key

•

Provide the corresponding public certificate to end-users so that it can be installed into SPC Certificate Store.

Locking Down a Mobile Computer

Like most configuration options in Windows Mobile, security settings are set via XML provisioning. For example, to enforce the “trusted” model and only allow applications signed with a privileged certificate to run, use the following provisioning document:

<wap-provisioningdoc>

</characteristic>

</wap-provisioningdoc>

For more information on various security options, refer to the Security Policy Settings topic in the latest Windows Mobile documentation.

Application Deployment 6 - 3

Installing Certificates

Use XML provisioning to query and delete certificates from certificate stores. To add a new certificate the Privileged Execution Trust Certificate Store, use the following sample provisioning document:

<wap-provisioningdoc>

<parm name= “EncodedCertificate” value= “

This is sample text. This is sample text. This is sample text. This is sample text.

This is sample text. This is sample text. This is sample text. This is sample text. = “/>

</characteristic>

</wap-provisioningdoc>

To create your own provisioning document with real certificate information:

1. Obtain a certificate from a security provider such as VeriSign.

2. Double-click on the certificate file (.CER) to open it.

3. Click on the Details tab and locate the Thumbprint field.

4. Copy the contents of the Thumbprint field and replace the value in the XML example above.

5. Click the Copy to File… button.

6. Click Next to start the Certificate Export Wizard.

7. Select Base-64 encoded X.509 (.CER) and then click Next.

8. Set the File Name to CertOutput.xml and click Next.

9. Click Finish to export the certificate.

10. Open the exported file, CertOutput.xml, in a text editor (i.e., NotePad).

11. Copy the contents of the file (excluding the first line, last line, and CR/LF) and replace the value of the

“EncodedCertificate” parameter in the xml example above.

Device Management Security

You can control access to certain device settings and security levels, such as installing applications and

changing security settings. Refer to the Windows Mobile Version 6 Help file for information on device

management security.

Remote API Security

The Remote API (RAPI) enables applications that run on a desktop to perform actions on a remote device. RAPI provides the ability to manipulate the file system on the remote device, including the creation and deletion of files and directories. By default, Zebra ships with RAPI in the restricted mode. Certain tools, such as

6 - 4 MC67 Integrator Guide

RAPIConfig, may not work properly. Refer to the Windows Mobile V ersion 6 Help file for finding information on

Remote API security policies.

Packaging

NOTE Applications compiled for Windows Mobile 6 are not backward-compatible with previous versions.

Packaging combines an application's executable files into a single file, called a package. This makes it easier to deploy and install an application to the MC67. Package new applications and updates, such as new DLL

files, as CAB files, then deploy them to devices. Refer to the Microsoft Windows Mobile 6 Help file for

information on CAB files.

Deployment

To install applications onto the MC67, developers package the application and all required files into a CAB file, then load the file onto the MC67 using one of the following options:

•

ActiveSync

•

Storage Card

•

MSP

•

Image Loader Image (for updating the operating system).

Refer to the Microsoft Windows Mobile 6 Help file for information on CAB files.

Installation Using ActiveSync

To install an application package:

1. Connect the MC67 to a host computer using ActiveSync. See Chapter 3, Synchronization for more

information.

2. Locate the package file on the host computer.

3. In ActiveSync on the host computer, open Explorer for the MC67.

4. Copy the CAB file from the host computer to the \temp directory on the MC67.

5. On the MC67, navigate to the \temp directory.

6. Tap on the application CAB file. The application installs on the MC67.

Installation Using Storage Card

To install an application package:

1. Copy the package CAB file to a microSD storage card using an appropriate storage card reader.

2. Install the storage card into the MC67. See Installing a microSD Card on page 1-2 for more information.

3. On the MC67, open File Explorer.

4. Open the Storage Card directory.

Application Deployment 6 - 5

5. Tap the package CAB file. The application installs on the MC67.

MSP

The MSP Client Software is a set of software components that come pre-installed on the MC67. The MSP Client software consists of the following components:

The RD Client provides support for MSP Staging functionality, provides support for the MSP Legacy Staging process, and provides support for backward-compatible legacy MSP 2.x Legacy Staging functionality.

The MSP Agent provides MSP Provisioning functionality and Control functionality when used with MSP Control Edition.

Refer to the Mobility Services Platform User’s Guide for instructions for using the Rapid Deployment and MSP3 Agent clients.

Update Loader Image

Windows Handheld contains an Image Update feature that updates all operating system components. All updates are distributed as update packages. Update packages can contain either partial or complete updates for the operating system. Zebra distributes the update packages on the Support Central Web Site,

http://www.

zebra.com/support

To update an operating system component, copy the update package to the MC67 using one of a variety of transports, including ActiveSync, a microSD card or MSP.

MC67NA Devices with Ortus Display

NOTE The MC67NA Base Model does not use the Ortus display.

If you are intending to install an older operating system version, verify if the device contains an Ortus display.

CAUTION If the display ID on the MC67NA is COM35H3N81, the device Operating System cannot be

downgraded to an OEM version below 03.46.36. If you try to downgrade, a message appears on the display warning you that you should not continue. If you continue, the device will become inoperable.

Figure 6-1

Warning Message

To view the display ID touch Start > Settings > System > System Info > Display tab or ConfigInfo tab.

6 - 6 MC67 Integrator Guide

ZEBRA

Figure 6-2

Figure 6-3

System Info - Display Tab

System Info - ConfigInfo Tab

To view the OEM version touch Start > Settings > System > System Info > System tab.

Figure 6-4

System Tab

Download Update Loader Package

1. Go to the Zebra Support Central web site, http://www.zebra.com/support.

2. Download the appropriate update loader package to a host computer.

Application Deployment 6 - 7

3. Locate the update loader package file on the host computer and un-compress the file into a separate

directory.

ActiveSync

To install an update loader package using ActiveSync:

1. Connect the MC67 to a host computer using ActiveSync. See Chapter 3, Synchronization for more

information.

2. In ActiveSync on the host computer, open Explorer for the MC67.

3. Copy all the update loader package files from the host computer to the \temp directory on the MC67.

4. On the MC67, navigate to the \temp directory.

5. Tap on the update loader file, STARTUPDLDR.EXE. The Update Loader application installs the update

loader package on the MC67.

A progress bar displays until the update completes.

6. The MC67 re-boots.

7. The calibration screen appears.

microSD Card

To install an update loader package using a microSD card:

1. Copy all the update loader package files to the root directory of a microSD card.

2. Install the microSD card into the MC67. See Installing a microSD Card on page 1-2 for installation

instructions.

3. Connect the MC67 to AC power. See Chapter 2, Accessories.

4. Perform a cold boot.

5. Immediately, as soon as the device starts to boot and before the splash screen is visible, press and hold

the left scan button.

6. The Update Loader application looks for the update loader file in the root directory of the microSD card.

When it finds the file, it loads the update loader package onto the MC67. A progress bar displays until the update completes.

7. The MC67 re-boots.

8. The calibration screen appears.

XML Provisioning

To configure the settings on an MC67, use XML provisioning. To install an XML provisioning file on the MC67, create a Cabinet Provisioning File (CPF). A CPF file is similar to a CAB file and contains just one file: _setup.xml. Like a CAB file, the CPF extension is associated with WCELoad.EXE. Opening a CPF extracts the XML code and uses it to provision and configure the MC67. The user receives an e-mail notification indicating success or failure.

XML provisioning provides the ability to configure various features of the MC67 (i.e., registry and file system). However, some settings require security privileges. To change registry settings via a CPF file, you must have

6 - 8 MC67 Integrator Guide

certain privileges (roles). Some registry keys require you to simply be an Authenticated User, while other registry keys require you to be a Manager. Refer to the Microsoft Windows Mobile 6 Help file, Metabase Settings for Registry Configuration Service Provider section, for the default role settings in Windows Mobile 6.

For those registry settings that require the Manager role, the CPF file must be signed with a privileged certificate installed on the device. Refer to the Microsoft Windows Mobile 6 Help file and the Windows Mobile 6 SDK for instructions and sample test certificates.

Creating an XML Provisioning File

To create a .cpf file:

1. Create a valid provisioning XML file named _setup.xml using an XML editor or the tools supplied with

Visual Studio 2005. (For example, use the SampleReg.xml sample created in the RegMerge on page 6-8

section and rename it _setup.xml.) Ensure the file contains the required parameters for the operation.

Refer to the Microsoft Windows Mobile 6 Help file for information.

2. In the Windows Mobile 6 tools directory on the desktop computer (typically \Program Files\Windows CE

Tools\wce500\Windows Mobile 6 Pocket PC SDK\Tools), run the Makecab.exe utility, using the following syntax to create a .cpf file from the _setup.xml file:

MakeCab.exe /D COMPRESS=OFF _setup.xml myOutCpf

NOTE COMPRESS=OFF is required for backward compatibility with Pocket PC.

3. Optionally, use the Authenticode tools to sign the .cpf file.

4. Tap the filename to install.

5. Certain applications and settings require a reset to take affect. In these cases, reset the MC67. Refer to the

Windows Mobile Version 6 Help file for more information.

XML Provisioning vs. RegMerge and Copy File

Prior to Windows Mobile 5.0, Zebra used two drivers (RegMerge and CopyFiles) to update the registry and to copy files during a reset. With Windows Mobile 6, Zebra recommends using XML provisioning instead. RegMerge and CopyFiles are supported for backward compatibility but Zebra may eliminate support in the future. The following sections provide examples of how RegMerge and CopyFiles were used, and how to perform the same function using XML provisioning.

RegMerge

RegMerge.dll is a built-in driver that allows updating the registry during a clean boot. RegMerge runs very early in the boot process and looks for registry files (.reg files) in certain Flash File System folders (i.e., \Application) during a clean boot. It then merges the registry changes into the system registry located in RAM.

The following example uses RegMerge to set a registry key:

SampleReg.reg

[HKEY_LOCAL_MACHINE\Hardware\DeviceMap\Backlight]

“BacklightIntensity”=dword:00000036

The following example uses XML provisioning to perform the same task:

Application Deployment 6 - 9

SampleReg.xml

<wap-provisioningdoc>

</characteristic>

</wap-provisioningdoc>

CopyFiles

CopyFiles copies files from one folder to another on a clean boot. During a clean boot CopyFiles looks for files with a .CPY extension in the root of the Application FFS partition. These files are text files containing the source and destination for the desired files to copy, separated by “>”.

The following example uses CopyFiles to copy a file from the \Application folder to the \Windows folder:

SampleCpy.cpy

The following example uses XML provisioning to perform the same task:

SampleCpy.xml

Storage

\Application\example.txt > \Windows\example.txt

<wap-provisioningdoc>

</characteristic>

</wap-provisioningdoc>

Mobile 6 contains three types of file storage:

•

Random Access Memory (RAM)

•

Persistent Storage

•

Application folder.

6 - 10 MC67 Integrator Guide

Random Access Memory

Executing programs use RAM to store data. Data stored in RAM is lost upon a warm boot. RAM also included

a volatile file storage area called Cache Disk.

Volatile File Storage (Cache Disk)

Windows Mobile 6 memory architecture uses persistent storage for all files, registry settings, and database objects to ensure data is retained even after a power failure. Persistent storage is implemented using Flash memory technology which is generally slower than volatile RAM memory. In certain situations the speed of the operation is more important than the integrity of the data. For these situations, Zebra has provided a small

volatile File Storage volume, accessed as the Cache Disk folder. Disk operations to the Cache Disk folder are

much faster than to any of the persistent storage volumes, but data is lost across warm boots and power

interruptions. Note that a backup battery powers RAM memory, including the Cache Disk, when you remove

the main battery for a short period of time.

The MC67 uses the Cache Disk for temporary data that can be restored from other sources, for example, for

temporarily “caching” HTML web pages by a browser or generating formatted files to send to a printer. Both situations benefit from the increased speed of the cache disk, but you can restore the data if needed.

DO NOT use the Cache Disk as a method to improve application performance. Analyze applications that

perform slower in persistent storage to optimize disk access. Common areas for optimization include minimizing the number of reads and writes to a file, removing unneeded debug logging, and minimizing file flushing or closing files.

Persistent Storage

Windows Mobile 6 protects all data and applications from power-related loss. Because Windows Mobile 6 mounts the entire file system and registry in persistent storage (rather than using RAM), MC67 devices provide a reliable storage platform even in the absence of battery power.

Persistent storage provides application developers with a reliable storage system available through the standard file system and registry APIs. Persistent storage is optimized for large reads and writes; therefore, applications reading and writing data in large chunks tend to outperform those applications reading and writing small blocks of data. Data in persistent storage is lost upon a reset.

Persistent storage contains all the directories under the root directory except for Application, Cache Disk, and Storage Card (if a storage card is installed). Persistent storage is approximately 1.1 GB (formatted).

Application Folder

The Application folder is a super-persistent storage that is persistent even after a reset. Accessing data in the Application folder is slower than accessing persistent storage. The Application folder is used for deployment and device-unique data. For example, network profiles can be stored in the Application folder so that connection to the network is available after a reset. The Application folder is approximately 510 MB (formatted).

Enterprise Mobility Developer Kits

The Enterprise Mobility Developer Kit (EMDK) family of products allows you to write applications that take advantage of the capture, move and manage capabilities of the MC67. Go to the Support Central (

http://www.

zebra.com/support) to download the appropriate developer kit.

Zebra MC67NA, MC67ND integrator Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Revision History

TABLE OF CONTENTS

ABOUT THIS GUIDE

Introduction

Documentation Set

Configurations

Software Versions

Chapter Descriptions

Notational Conventions

Related Documents

Service Information

CHAPTER 1 GETTING STARTED

Introduction

Unpacking

Getting Started

Installing a microSD Card

Installing the SIM Card

Installing the Battery

Charging the Battery

Charging the Main Battery

Charging Spare Batteries

Charging Temperature

Powering On the MC67

Calibrating the Screen

Network Activation

Activating an MC67ND on a CDMA Network

Switching from CDMA to GSM/UMTS

Switching from GSM/UTMS to CDMA

Replacing the Battery

Resetting the MC67

Performing a Warm Boot

Performing a Cold Boot

Performing a Clean Boot

Waking the MC67

CHAPTER 2 ACCESSORIES

Introduction

Single Slot USB Cradle

Setup

Charging the MC67 Battery

Charging the Spare Battery

Battery Charging Indicators

Charging Temperature

Single Slot Ethernet/Modem/USB Cradle

Country Settings

Setup

Indicators

MC67 Software Setup

Ethernet Setup

Modem Setup

Four Slot Ethernet Cradle

CRD5500-4000ER Setup

Daisychaining Ethernet Cradles

LED Indicators (CRD5500-4000ER)

CRD5501-4001ER Setup

Daisychaining Ethernet Cradles

LED Indicators (CRD5501-4001ER)

Ethernet Cradle Drivers

Charging

Four Slot Charge Only Cradle

Setup

Charging Temperature

Wall Mount Bracket

VCD5500 Vehicle Cradle

Requirements

Connector Pin-Outs

Mounting the Cradle

Power Connection

Charging the MC67 Battery

Removing the MC67

Battery Charging Indicators

Charging Temperature

Four Slot Battery Charger

Spare Battery Charging

Battery Charging Indicators

Charging Temperature

Cables