MC67
WITH ANDROID™ OS
QUICK START GUIDE
FEATURES CARD INSTALLATION
Note: Remove protective shipping film that covers the touch screen, exit
window and camera window before using.
9
12
10
11
8
7
1
2
6
3
(Note 1)
4
1 Scan/Action Button
2 Up/Down Button
3 Microphone
4 Power Button
5 I/O Connector
6 Keypad
8 Touch Screen (with screen
protector)
9 Data Capture LED
10 Charging/Battery Status LED
11 WAN Radio Status LED
12 Phone Speaker
5
7 Scan/Action Button
Note 1: To reset the MC67, press and hold the Power button until the menu appears
and then select Reset.
13
14
15
16
17
18
19
13 Handstrap
14 Battery
15 Battery Latch
16 Camera Flash
17 Camera
18 Exit Window (see Data Capture
Options)
Notifications
Data Capture LED:
Green: Good Decode
Charging/Battery Status LED:
Slow blinking amber: Battery charging
Solid amber: Fully charged
Fast blinking amber: Charging error
Radio Status LED:
Green: RF active
23
22
21
20
19 Tether
20 Scan/Action Button
21 Action Button
22 Stylus
23 Speaker
Data Capture
Charging/Battery Status
Radio Status
2
2
7
6
9
2
3
2
3
2
2
8
1
5
7
9
Numeric Keypad
2
2
7
5
6
9
Blue Key
Use this key to access application dependent
function keys shown on the keypad in blue.
>
Orange Key
Use this key to access the secondary layer of characters
>
>
2
3
Orange Key
2
Use this key to access the secondary
8
layer of characters.
>
>
DSD Keypad
Press the Blue key once to activate this state, followed
by another key.
Press the Orange key once to lock the keypad into
Alpha state.
Press the Orange key a second time to return to the
normal state.
2
3
3
Alpha-Numeric Keypad
Press the Orange key once to lock the
keypad into Alpha state.
Press the Orange key a second time to
return to the normal state.
1 Talk
2 Navigation
3 Scan/Action Button
4 End
5 Orange Key
6 Blue Key
7 Home
8 Menu
9 Back
MicroSD Card Installation (Optional)
1. Remove the handstrap.
2
2. Lift the rubber access door.
4
3. Slide the SIM card holder up to
unlock.
4. Lift the SIM card holder.
5. Carefully lift the microSD card holder.
6. Insert the microSD card into the
5
8
card holder.
NOTE :
Proper position of the microSD card — the card
connector (i.e., gold contacts) should be facing out as
shown.
7. Gently lower the microSD card holder until it snaps
into place.
SIM Card Installation (Optional)
8. Insert the SIM card into the SIM holder.
NOTE :
The proper position of the SIM card—the card
connector (i.e., gold area) should be facing outward
with the beveled corner facing away.
9. Lower the SIM card holder.
10. Slide the SIM card holder down to lock into place.
11. Close the rubber access door.
12. Install the battery.
SIM Card Holder
Rubber Access Door
microSD Card Holder
2
3
BATTERY REMOVAL
BATTERY INSTALLATION
DATA CAPTURE OPTIONS
AVOID EXTREME WRIST ANGLES
1. Unlatch the handstrap.
2. Press the Power button until the menu appears.
3. Touch Battery Swap.
4. Wait for the red LED to turn off.
5. Slide the battery latch to the right. The battery ejects slightly.
6. Grasp the battery and lift from the MC67.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo
is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.
©2015 Symbol Technologies Inc.
MN000114A02 Rev. A — February 2015
1. Insert the battery, bottom first, into the battery compartment.
2. Press down on the battery until the battery latch snaps into
place.
3. Replace the handstrap.
2
1
3
For more information see the MC67 User Guide and the MC67 Integator Guide available at:
www.zebra.com/support
Imaging
1. Ensure that an application is open and a text field is in focus (text
cursor in text field).
2. Point the exit window at the bar code.
3. Press and hold the Scan button.
4. The red laser aiming pattern turn on to assit in aiming. When
the MC67 decodes the bar code the Scan/Decode LED light green
and a beep sounds.
5. Release the Scan button.
Camera Decode
1. Ensure that an application is open and a text
field is in focus (text cursor in text field).
2. Point the MC67 at the bar code.
3. Press the Scan button.
4. In the image window align the red target
over the bar code. When the MC67 decodes
the bar code the Scan/Decode LED light
green and a beep sounds.
5. Release the Scan button.
Camera Photo
1. Touch > Camera.
2. Point the MC67 at an object.
3. Touch the shutter button.
GPS Information
When using the GPS feature of the MC67:
• Acquiring satellite signals may take a few minutes. It is best to be outside and
have a clear, unobstructed view of the sky.
• Without a clear view, acquisition takes much longer and could result in the
MC67 being unable to compute the initial position quickly.
• Obtain a satellite fix before moving.
• Shutdown GPS application when not in use.
AVOID EXTREME
WRIST ANGLES
Loading...