VCD5500 Vehicle Cradle
Quick Reference Guide
2 VCD5500 Vehicle Cradle
Zebra reserves the right to make changes to any product to improve reliability,
function, or design.
Zebra does not assume any product liability arising out of, or in connection with,
the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Zebra products might
be used. An implied license exists only for equipment, circuits, and subsystems
contained in Zebra products.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The
Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra
Technologies company. All other trademarks are the property of their respective
owners.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Quick Reference Guide 3
Introduction
This guide describes how to install and use a VCD5500 vehicle cradle with a
Zebra MC55 Enterprise Digital Assistant.
Install the VCD5500 into your vehicle. Once installed, the cradle:
• holds the MC55 securely in place
• provides power for operating the MC55
• re-charges the battery in the MC55.
The cradle is powered by the vehicle’s 12V or 24V electrical system. The
operating voltage range is 9V to 32V and requires a maximum current of 3A.
About This Guide
Specific topics in this guide include:
• Requirements on page 3
• Parts on page 4
• Mounting the Cradle on page 5
• Power Connection on page 6
• MC55 Insertion and Removal on page 9
• MC55 Battery Charging on page 10
• LED Indicators on page 10
• Care and Cleaning on page 11
• Troubleshooting on page 11
• Regulatory Information on page 13
• Service Information on backcover.
For detailed information about the series of MC55, refer to the MC55 User Guide
(p/n 72E-108859-xx), and the MC55 Integrator Guide (p/n 72E-108861-xx).
Requirements
For mounting:
• four #8-32 self-locking nuts (included)
• four #8 washers (included)
• a drill with a #6 drill bit (.204”).
4 VCD5500 Vehicle Cradle
FRONT VIEW
Release Lever
Power Port
BOTTOM VIEW
REAR VIEW
Mounting Screws
Release Lever
For power connection:
• power input cable (included), p/n 25-61987-01R
• UL Listed in-line fuse rated 250V, 5A (included), must be used if not connecting
to vehicle’s fuse panel
• in-line fuse holder (included), must be used if not connecting to vehicle’s fuse
panel.
Parts
Quick Reference Guide 5
1
Connector on Power Cable
Connector Pin-Outs
Power Input Cable
Pin Signal
1 Chassis ground (Black Wire)
2 Chassis ground (Bare Wire)
3 V+ (Red Wire)
4 V+ (Red Wire)
CAUTION ROAD SAFETY - Do not use the MC55 while driving. Park
the vehicle first. Always ensure the MC55 is fully inserted into
the cradle. Do not place it on the seat or where it can break
loose in a collision or sudden stop. Lack of proper insertion
may result in property damage or personal injury. Zebra is not
responsible for any loss resulting from the use of the
products while driving. Remember: Safety comes first.
Mounting the Cradle
CAUTION Only mount the Vehicle Cradle in a vertical position with the
release level at the top or in a horizontal position with the
mobile computer display facing up. Never mount the vehicle
cradle on the side or upside down or on a wall that can be
subject to impact or collision of greater than 40Gs, in
accordance with SAE J1455 Section 4.10.3.5
1. Select a mounting location for the cradle. It should be flat, and must provide
adequate support for the cradle.
6 VCD5500 Vehicle Cradle
1.5”
1.2”
2. Prepare the mounting surface to accept four #8-32 studs, using the mounting
template below. Drill four holes with a #6 drill bit.
3. Position the cradle on the mounting surface.
4. Fasten it using four #8 washers and four #8-32 self-locking nuts.
CAUTION Do not install a Vehicle Cradle on or near an air bag cover
plate or within an aerobic zone. Also, do not install it in a
location that affects vehicle safety or driveability.
Power Connection
Please read all of these instructions before beginning.
To connect the cradle to power:
WARNING
CAUTION When setting up connection for this cradle, only use the
! A properly trained technician must perform the power
connection. Improper connection can damage your vehicle,
cradle or mobile computer. Refer to the vehicle’s Owner’s
Manual for instructions for removing power.
power input cable provided with this cradle.
Loading...