
Regulatory Information
All Zebra devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Local language translations are available at the following website:
http://www.zebra.com/support
Any changes or modifications to Zebra equipment, not expressly approved
by Zebra could void the user’s authority to operate the equipment.
For use only with Zebra approved and UL Listed mobile computers. Zebra
approved and UL Listed accessories and/or Zebra approved and UL Listed/
Recognized battery packs.
CAUTION Only use Zebra approved and UL Listed accessories,
battery packs and battery chargers.
Do NOT attempt to charge damp/wet mobile computers or
batteries. All components must be dry before connecting to
an external power source.
Power Supply
Model Description
SAC5500-4000 Four Slot Battery Charger
CRD5500-1000 Single Slot USB Cradle
CRD5500-4000
CRD5501-4000CR
CRD5500-4000E
CRD5501-4000ER
25-108022-02R
25-108022-03R
25-112560-02R Charge-only Cable
Four Slot Charge Only Cradle
Four Slot Ethernet Cradle
USB Charge Cable
SAC5500-4000 and CRD5500-1000
Use only a Zebra approved, certified power supply rated 12 VDC, 4.16 A
Min, 40°C Min., LPS. Use of an alternate power supply will invalidate any
approvals given to this unit and may be dangerous.
CRD5500-4000, CRD5501-4000CR, CRD5500-4000E and
CRD5501-4000ER
Use only a Zebra approved, certified power supply rated 12 VDC, 9 A Min,
40° C Min. Use of an alternate power supply will invalidate any approvals
given to this unit and may be dangerous.
25-108022-02R, 25-108022-03R and 25-112560-02R
Use only a Zebra approved, certified power supply rated 5.4 VDC, 3 A Min,
40° C Min. LPS. Use of an alternate power supply will invalidate any
approvals given to this unit and may be dangerous.
Using MSR5500-100R
USB Charge Cable (25-108022-03R) is not recommended for use with the
MSR5500-100R. Remove the MSR from the mobile computer before
attempting to charge or ActiveSync.
Vehicle Installation
RF signals may affect improperly installed or inadequately shielded
electronic systems in motor vehicles (including safety systems). Check with
the manufacturer or its representative regarding your vehicle. You should
also consult the manufacturer of any equipment that has been added to your
vehicle.
An air bag inflates with great force. DO NOT place objects, including either
installed or portable wireless equipment, in the area over the air bag or in the
air bag deployment area. If in-vehicle wireless equipment is improperly
installed and the air bag inflates, serious injury could result.
Position your device within easy reach. Be able to access your device
without removing your eyes from the road.
Note: Connection to an alert device that will cause a vehicle horn to sound or
lights to flash, on receipt of a call on public roads, is not permitted.
Safety on the Road
Do not take notes or use the device while driving. Jotting down a “to do” list
or flipping through your address book takes attention away from your primary
responsibility, driving safely.
When driving a car, driving is your first responsibility - Give full attention to
driving. Check the laws and regulations on the use of wireless devices in the
areas where you drive. Always obey them.
When using a wireless device behind the wheel of a car, practice good
common sense and remember the following tips:
1. Get to know your wireless device and any features such as speed dial
and redial. If available, these features help you to place your call without
taking your attention off the road.
2. When available, use a hands free device.
3. Let the person you are speaking with know you are driving; if necessary,
suspend the call in heavy traffic or hazardous weather conditions. Rain,
sleet, snow, ice, and even heavy traffic can be hazardous.
4. Dial sensibly and assess the traffic; if possible, place calls when you are
not moving or before pulling into traffic. Try to plan calls when your car
will be stationary. If you need to make a call while moving, dial only a few
numbers, check the road and your mirrors, then continue.
5. Do not engage in stressful or emotional conversations that may be
distracting. Make people you are talking with aware you are driving and
suspend conversations that have the potential to divert your attention
from the road.
6. Use your wireless phone to call for help. Dial the Emergency services,
(9-1-1 in the US, and 1-1-2 in Europe) or other local emergency number
in the case of fire, traffic accident or medical emergencies. Remember, it
is a free call on your wireless phone! The call can be made regardless of
any security codes and depending on a network, with or without a SIM
card inserted.
7. Use your wireless phone to help others in emergencies. If you see an
auto accident, crime in progress or other serious emergency where lives
are in danger, call the Emergency Services, (9-1-1 in the US, and 1-1-2
in Europe) or other local emergency number, as you would want others
to do for you.
8. Call roadside assistance or a special non-emergency wireless assistance
number when necessary. If you see a broken-down vehicle posing no
serious hazard, a broken traffic signal, a minor traffic accident where no
one appears injured, or a vehicle you know to be stolen, call roadside
assistance or other special non-emergency wireless number.
“The wireless industry reminds you to use your device / phone safely when
driving.”
Warnings for Use of Wireless Devices
Please observe all
devices.
warning notices with regard to the usage of wireless
Potentially Hazardous Atmospheres
You are reminded of the need to observe restrictions on the use of radio
devices in fuel depots, chemical plants etc. and areas where the air contains
chemicals or particles (such as grain, dust, or metal powders) and any other
area where you would normally be advised to turn off your vehicle engine.
Batteries
Taiwan - Recycling
EPA (Environmental Protection Administration)
requires dry battery producing or importing firms in
accordance with Article 15 of the Waste Disposal
Act are required to indicate the recycling marks on
the batteries used in sales, giveaway or promotion.
Contact a qualified Taiwanese recycle for proper battery disposal.
Battery Information
Use only Zebra approved batteries. Accessories which have battery charging
capability are approved for use with the following battery models:
• Zebra 82-107172-01 (3.7 VDC, 2400 mAh)
• Zebra 82-111094-XX* (3.7 VDC, 3600 mAh)
*Note: XX represents battery enclosure color (01=black, 02=white)
Zebra rechargeable battery packs are designed and constructed to the
highest standards within the industry.
However, there are limitations to how long a battery can operate or be stored
before needing replacement. Many factors affect the actual life cycle of a
battery pack, such as heat, cold, harsh environmental conditions and severe
drops.
When batteries are stored over six (6) months, some irreversible
deterioration in overall battery quality may occur. Store batteries at half of full
charge in a dry, cool place, removed from the equipment to prevent loss of
capacity, rusting of metallic parts and electrolyte leakage. When storing
batteries for one year or longer, the charge level should be verified at least
once a year and charged to half of full charge.
Replace the battery when a significant loss of run time is detected.
Standard warranty period for all Zebra batteries is one year, regardless if the
battery was purchased separately or included as part of the mobile
computer. For more information on Zebra batteries, please visit
http://www.zebra.com/batterybasics.
CAUTION Risk of explosion if battery is replaced by an incorrect type.
Dispose of batteries according to instructions.
Battery Safety Guidelines
• The area in which the units are charged should be clear of debris and
combustible materials or chemicals. Particular care should be taken
where the device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in the
user's guide.
• Improper battery use may result in a fire, explosion, or other hazard.
• To charge the mobile device battery, the battery and charger
temperatures must be between +32ºF and +104ºF (0ºC and +40ºC)
• Do not use incompatible batteries and chargers. Use of an incompatible
battery or charger may present a risk of fire, explosion, leakage, or other
hazard. If you have any questions about the compatibility of a battery or a
charger, contact Zebra support.
• For devices that utilize a USB port as a charging source, the device shall
only be connected to products that bear the USB-IF logo or have
completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Severe impact from dropping any battery-operated device on a hard
surface could cause the battery to overheat.
• Do not short circuit a battery or allow metallic or conductive objects to
contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign objects into the
battery, immerse or expose to water or other liquids, or expose to fire,
explosion, or other hazard.
• Do not leave or store the equipment in or near areas that might get very
hot, such as in a parked vehicle or near a radiator or other heat source.
Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to promptly dispose of used re-chargeable
batteries.
• Do not dispose of batteries in fire.
• Seek medical advice immediately if a battery has been swallowed.
• In the event of a battery leak, do not allow the liquid to come in contact
with the skin or eyes. If contact has been made, wash the affected area
with large amounts of water and seek medical advice.
• If you suspect damage to your equipment or battery, contact Zebra
support to arrange for inspection.
Radio Frequency Interference Requirements-FCC
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

Zebra reserves the right to make changes to any product to improve
72-108863-05 Revision A — September 2018
reliability, function, or design. Zebra does not assume any product liability
arising out of, or in connection with, the application or use of any product,
circuit, or application described herein. No license is granted, either
expressly or by implication, estoppel, or otherwise under any patent right or
patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which Zebra products might be
used. An implied license exists only for equipment, circuits, and subsystems
contained in Zebra products.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
© 2018 ZIH Corp. and/or its affiliates. All rights reserved. ZEBRA and
the stylized Zebra head are trademarks of ZIH Corp., registered in many
jurisdictions worldwide. All other trademarks are the property of their
respective owners.Zebra and the stylized Zebra head are trademarks of
ZIH Corp., registered in many jurisdictions worldwide. All other
trademarks are the property of their respective owners.
Radio Frequency Interference Requirements –
Canada
Innovation, Science and Economic Development Canada ICES 003
Compliance Label: CAN ICES-3 (B)/NMB-3(B)
Marking and European Economic Area
(EEA)
Statement of Compliance
Zebra hereby declares that this device is in compliance with all applicable
Directives, 2014/30/EU, 2014/35/EU and 2011/65/EU. The full text of the EU
Declaration of Conformity is available at the following internet address: http://
www.zebra.com/doc.
Japan (VCCI) - Voluntary Control Council for
Interference
Class B ITE
この装置は、クラス B 機 器です。この装置は、住宅環境 で使用する
ことを目的としていますが、この装置がラジオやテレビジョ ン受信機
に近接して使用されると、受信障害を引き起こすことがあい ます。 取
扱説明書に従って正しい取い扱いをして下さい。 VCCI-B
Korea Warning Statement for Class B ITE
기 종 별 사 용 자 안 내 문
B급 기기
( 가정용
방송통신기자재 )
이 기기는 가정용 (B 급 ) 전자파적합기기로서
가정에서 사용하는 것을 목적으로 하며, 모든
지역에서 사용할 수 있습니다 .
주로
Waste Electrical and Electronic Equipment
(WEEE)
English: For EU Customers: All products at the end of their life must be
returned to Zebra for recycling. For information on how to return product, please go
to: http://www.zebra.com/weee.
Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie
doivent être retournés à Zebra pour recyclage. Pour de plus amples informations
sur le retour de produits, consultez : http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán
entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea
más información sobre cómo devolver un producto, visite:
http://www.zebra.com/weee.
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти
трябва да се връщат на Zebra за рециклиране. За информация относно
връщането на продукти, моля отидете на адрес: http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo
ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per
informazioni sulle modalità di restituzione, visitare il seguente sito Web:
http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser
devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver
o produto, visite: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun
levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://
www.zebra.com/weee voor meer informatie over het terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y
zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów
znajduj¹ siê na stronie internetowej http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich
životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení
produktu najdete na webové stránce: http://www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz
kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával
kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti
podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite:
http://www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste
returneras till Zebra för återvinning. Information om hur du returnerar produkten
finns på http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når
de er udtjent. Læs oplysningerne om returnering af produkter på:
http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής
τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες
πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση
http://www.zebra.com/weee στο ∆ιαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu
tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif
għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí
doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o
vrátení výrobkov nájdete na: http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti
grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį,
rasite: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā
atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu
nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or
Systems Support. If there is a problem with the equipment, they will contact
Zebra Global Support at: http://www.zebra.com/support.
the
For the latest version of this guide go to: http://www.zebra.com/support
MC55 ACCESSORIES
REGULATORY GUIDE