Zebra AP-6521E Installation Manual

AP-6521E SERIES ACCESS POINT

INSTALLATION GUIDE

2 AP-6521E Series Access Point

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered
trademark of Symbol Technologies, Inc., a Zebra Technologies company.

© 2015 Symbol Technologies, Inc.

Installation Guide 3

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.0 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Access Point Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3.1 Antenna Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3.2 Power Injector System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.4 Wall Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.5 Suspended Ceiling T-Bar Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.6 Above the Ceiling (Plenum) Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.7 LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.0 Basic WiNG Express Access Point Configuration . . . . . . . . . . . . . . . . . . . . 19

4.0 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.2 Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.3 Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.1 Regulatory Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.2 Wireless Device Country Approvals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.2.1 Country Selection - Note for AP & Wireless Controller. . . . . . . . . . . . . . . 30

5.2.2 Frequency of Operation - FCC and IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.3 Health and Safety Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.3.1 Warnings for the use of Wireless Devices . . . . . . . . . . . . . . . . . . . . . . . . 31

5.3.2 Potentially Hazardous Atmospheres - Fixed Installations . . . . . . . . . . . . . 31

4 AP-6521E Series Access Point

5.3.3 Safety in Hospitals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.4 RF Exposure Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5.4.1 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5.5 International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5.6 EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5.7 US and Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5.8 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5.9 Radio Frequency Interference Requirements - FCC . . . . . . . . . . . . . . . . . . . . . . 33

5.10 Radio Frequency Interference Requirements - Canada . . . . . . . . . . . . . . . . . . 33

5.4.1 Radio Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5.11 CE Marking and European Economic Area (EEA) . . . . . . . . . . . . . . . . . . . . . . . 34

5.12 Mexico . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.13 Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.14 Waste Electrical and Electronic Equipment (WEEE). . . . . . . . . . . . . . . . . . . . . 35

5.15 Turkish WEEE Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5.16 Japan (VCCI) - Voluntary Control Council for Interference Class B ITE . . . . . . 37

5.17 Korea Warning Statement for Class B ITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.18 Other Countries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

6.0 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

7.0 AP-6521 Series Access Point China ROHS Agreement . . . . . . . . . . . . . . . . 41

Installation Guide 5

1 Introduction

An AP-6521 Series Access Point links wireless 802.11a/b/g/n devices to the controller, enabling the growth of your
wireless network with a cost-effective alternative to standard Access Points. The AP-6521 Series Access Point is
an enterprise class 802.11n Access Point, installed in minutes anywhere a CAT-5e (or better) cable is located.

The Access Points ship with a single dual-band radio supporting the 802.11a/b/g/n radio bands. For more
information on available SKUs, refer to the following:

Part Number Description

AP-6521-60010-US 802.11a/b/g/n single radio, integrated antenna, high power, United States model

AP-6521-60020-US 802.11a/b/g/n single radio, external antenna, high power, United States model

AP-6521-60010-EU 802.11a/b/g/n single radio, integrated antenna, high power, European model

AP-6521-60020-EU 802.11a/b/g/n single radio, external antenna, high power, European model

AP-6521-60010-WR 802.11a/b/g/n single radio, integrated antenna, high power, World Wide model

AP-6521-60020-WR 802.11a/b/g/n single radio, external antenna, high power, World Wide model

AP-6521E-60010-US 802.11a/b/g/n single radio, integrated antenna, high power, United States model

AP-6521E-60020-US 802.11a/b/g/n single radio, external antenna, high power, United States model

AP-6521E-60010-EU 802.11a/b/g/n single radio, integrated antenna, high power, European model

AP-6521E-60020-EU 802.11a/b/g/n single radio, external antenna, high power, European model

AP-6521E-60010-WR 802.11a/b/g/n single radio, integrated antenna, high power, World Wide model

AP-6521E-60020-WR 802.11a/b/g/n single radio, external antenna, high power, World Wide model

The Access Point is approved under MODEL: NCAP-500.
The Access Point should receive power and transfer data through the same CAT-5e (or better) Ethernet cable using

a Power Injector. The Power Injector (Part No. AP-PSBIAS-2P2-AFR) is an 802.3af PoE injector. For information, see

Power Injector System.

A separate power supply (Part No. PWRS-147376-01R) is also available if you do not wish to use a Power Injector.
This standard power supply just supplies power to the Access Point’s power connector and does not converge
power and Ethernet within a single cable connection.

6 AP-6521E Series Access Point

!

!

1.1 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

NOTE Tips, hints, or special requirements that you should take note of.

CAUTION Care is required. Disregarding a caution can result in data loss or

equipment malfunction.

WARNING! Indicates a condition or procedure that could result in personal injury or

equipment damage.

1.2 Warnings

• Read all installation instructions and site survey reports, and verify correct equipment installation before
connecting the Access Point.

• Remove jewelry and watches before installing this equipment.

• Verify any device connected to this unit is properly wired and grounded.

• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment
operation specifications.

1.3 Site Preparation

• Consult your site survey and network analysis reports to determine specific equipment placement, power

drops, and so on.

• Assign installation responsibility to the appropriate personnel.

• Identify and document where all installed components are located.

• Ensure adequate, dust-free ventilation to all installed equipment.

• Prepare Ethernet port connections.

• Verify cabling is within the maximum 100 meter allowable length.

1.4 Package Contents

The Access Point is available in integrated antenna and external antenna models. Contents differ depending on
the Access Point type ordered.

• Access Point

• Installation Guide (This Guide)

• Rubber Wall Mount Spacers (4)

• LED light pipe and badge

• Wall mount screw and anchor kit

Installation Guide 7

1.5 Features

• One RJ-45 console connector

• LED indicators

• Safety wire tie point

• Wall mount slots

• Clips for suspended T-Bar mounting

• DC power connector

An AP-6521 Series Access Point has one RJ-45 connector supporting an 10/100/1000 Ethernet port connection and
requires 802.3af compliant power from an external source.

The Access Point contains runtime firmware which enables the unit to boot after either a power up or a watchdog
reset. The runtime firmware on the Access Point can be updated via the Ethernet interface.

8 AP-6521E Series Access Point

2 Hardware Installation

2.1 Installation Instructions

The Access Point can attach to a wall, mount under a suspended T-Bar or mount above a ceiling. Select a mounting
option based on the physical environment of the coverage area. Do not mount the Access Point in a location that
has not been approved in a site survey.

To prepare for the installation, perform the following:

1. Verify the contents of the box includes the intended Access Point and accessory hardware.

2. Review site survey and network analysis reports to determine the location and mounting position for the
Access Point.

3. Connect a CAT-5 or better Ethernet cable to a PoE compatible device and run the cable to the installation
site. Ensure there is sufficient cable slack to perform the installation steps.

4. Determine whether the Access Point is powered using a Power Injector system, combining data and
power to the Access Point’s GE1/PoE port or will be powered from a conventional power adapter
providing power only to the Access Point’s DC-48V connector.

2.2 Precautions

Before installing the Access Point:

• Verify the intended deployment location is not prone to moisture or dust.

• Verify the environment has a continuous temperature range between 0° C to 40° C.

Installation Guide 9

2.3 Access Point Placement

For optimal performance, install the Access Point away from transformers, heavy-duty motors, fluorescent lights,
microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls
or floors block transmission. Install the Access Point in an open area or add Access Points as needed to improve
coverage.

Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough. An
area lit sharply might minimize coverage and create dark areas. Uniform antenna placement in an area (like even
placement of a light bulb) provides even, efficient coverage.

Place the Access Point using the following guidelines:

• Install the Access Point at an ideal height of 10 feet from the ground.

• Orient the Access Point antennas vertically for best reception.

• Point the Access Point antennas downward if attaching to the ceiling (external antenna models only).

To maximize the Access Point’s radio coverage area, conduct a site survey to define and document radio
interference obstacles before installing the Access Point.

2.3.1 Antenna Options

Two antenna suites are supported for the single radio, dual-band AP-6521 Series Access Point. One antenna suite
supporting the 2.4 GHz band, and another antenna suite supporting the 5 GHz band. Select an antenna best suited
to the intended operational environment of your Access Point.

10 AP-6521E Series Access Point

The 2.4 GHz antenna suite includes the following models:

Part Number Antenna Type Approximate Gain (dBi)

ML-2452-APA2-01 Dipole 3

ML-2452-HPA5-036 Dipole 2.9

ML-2499-HPA3-01R Dipole 4.6

ML-2499-APA2-01R Dipole 2

ML-2452-APA2GA1-01 Dipole 2

ML-2452-PNA5-01R Panel 4.5

ML-2452-PTA3M3-36 Patch 5

ML-2499-SD3-01R Patch 4.8

Internal Antenna PIFA 2.4

The 5 GHz antenna suite includes the following models:

Part Number Antenna Type Approximate Gain (dBi)

ML-2452-APA2-01 Dipole 5

ML-2452-HPA5-036 Dipole 4.9

ML-5299-APA1-01R Dipole 2

ML-5299-HPA1-01R Dipole 5

ML-2452-APA2GA1-01 Dipole 1

ML-2452-PNA5-01R Panel 5

ML-2452-PTA3M3-36 Patch 3

ML-5299-PTA1-0R Patch 5

Internal Antenna PIFA 6

For a more exhaustive overview of the antennas and associated components supported, refer to the Enterprise
Wireless LAN Antenna Specification Guide available at www.zebra.com/support

.

Installation Guide 11

2.3.2 Power Injector System

The Access Point can receive power via an Ethernet cable connected to the GE1/PoE port.

When users purchase a WLAN solution, they often need to place Access Points in obscure locations. In the past, a
dedicated power source was required for each Access Point in addition to the Ethernet infrastructure. This often
required an electrical contractor to install power drops at each Access Point location. The Power Injector merges
power and Ethernet into one cable, reducing the burden of installation and allowing optimal Access Point
placement in respect to the intended coverage area.

The Power Injector (Part No. AP-PSBIAS-2P2-AFR) is an 802.3af PoE injector. The Access Point can only use a Power
Injector when connecting to the Access Point’s GE1/PoE port. The Power Injector is separately ordered and not
shipped with the Access Point. A separate Power Injector is required for each Access Point comprising the network.

The Power Injector has no On/Off power switch. The Injector receives power and is ready for device connection and
operation as soon as AC power is applied. Refer to the Installation Guide shipped with the Power Injector for a
description of the device’s LEDs.The Power Injector can be installed free standing, on an even horizontal surface or
wall mounted using the Power Injector’s wall mounting key holes.

12 AP-6521E Series Access Point

!

!

The following guidelines should be adhered to before cabling the Power Injector to an Ethernet source and an
Access Point:

• Do not block or cover airflow to the Power Injector.

• Keep the Power Injector away from excessive heat, humidity, vibration and dust.

• The Power Injector isn’t a repeater, and does not amplify the Ethernet signal. For optimal performance,
ensure the Power Injector is placed as close as possible to the Ethernet switch. This allows the Access
Point to be deployed away from power drops.

• Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does not
exceed 100 meters (333 ft).

CAUTION To avoid problematic performance and restarts, disable POE from a

wired controller port connected to an Access Point if mid-span power
sourcing equipment (PSE) is used between the two, regardless of the

manufacturer.

CAUTION Ensure AC power is supplied to the Power Injector using an AC cable

with an appropriate ground connection approved for the country of
operation.

NOTE If not using the Power Injector to power the Access Point, the only other

approved power solution is the standard power supply (Part Number
PWRS-147376-01R). The standard power supply does not converge data
and power in one cable, and requires a separate data Ethernet
connection in addition to a power connection. This product is intended to
be supplied by a listed power adapter marked “Class 2” or “L.P.S” (or
“Limited Power Source”) and rated from 48Vdc, 0.27A minimum.

Installation Guide 13

!

2.4 Wall Mount Installation

To support wall mount installations, the Access Point is fastened directly to a flat wall surface. The wall should be
of gypsum board, plaster, wood or concrete in composition.

CAUTION An Access Point should be wall mounted to concrete or

plaster-wall-board (dry wall) only. Do not wall mount the Access Point
to combustible surfaces.

To install the Access Point to a wall surface:

1. Orient the Access Point by either its width or length.

2. Mark the mounting surface at the target screw insertion points.

3. At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall mounting screw and
stop when there is 1mm between the screw head and the wall.

4. If pre-drilling a hole, the recommended hole size is 2.8mm (0.11in.) if the screws are going directly into
the wall and 6mm (0.23in.) if wall anchors are being used.

5. If required, install and attach a security cable to the Access Point lock port.

6. Attach the antennas to their correct connectors.
For information on available antennas, see

7. Place the large center opening of each of the mount slots over the screw heads.

8. Slide the Access Point down along the mounting surface to hang the mount slots on the screw heads.

9. Cable the Access Point using either the Power Injector solution or an approved line cord and power supply.

For Power Injector installations:

a. Connect an RJ-45 CAT5 Ethernet cable between the network data supply (host) and the Power

Injector’s Data In connector.

b. Connect an RJ-45 CAT5 Ethernet cable between the Power Injector’s Data & Power Out connector

and the Access Point.

c. Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does

not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch. The Power Injector
receives power as soon as AC power is applied. For more information, see

Antenna Options.

Power Injector System.

For power adapter (Part Number PWRS-147376-01R) and line cord installations:

a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the

Access Point’s GE1/PoE.
b. Verify the power adapter is correctly rated according the country of operation.
c. Connect the power supply line cord to the power adapter.
d. Attach the power adapter cable to the DC-48V power connector on the Access Point.

14 AP-6521E Series Access Point

!

e. Attach the power supply line cord to a power supply.

10. Verify the behavior of the Access Point LEDs. For more information, see

11. The Access Point is ready to configure. For information on basic Access Point device configuration, see

Basic Access Point Configuration.

LED Indicator.

2.5 Suspended Ceiling T-Bar Installation

A suspended ceiling mount requires holding the Access Point up against the T-bar of a suspended ceiling grid and
twisting the Access Point chassis onto the T-bar.

To install the Access Point on a ceiling T-bar:

1. If desired, install and attach a security cable to the Access Point lock port.

2. If using an external antenna model, attach the antennas to their correct connectors.

3. For more information on the antenna options available to the Access Point, see

4. Cable the Access Point using either the Power Injector solution or an approved line cord and power supply.

CAUTION Do not connect to the power source until the cabling of the Access

Point is complete. Ensure PoE is not connected to the Access Point’s
console connector or risk rendering the console connector
permanently inoperable.

Antenna Options.

For Power Injector installations:

a. Connect an RJ-45 CAT5 Ethernet cable between the network data supply (host) and the Power

Injector’s Data In connector.
b. Connect an RJ-45 CAT5 Ethernet cable between the Power Injector’s Data & Power Out connector

and the Access Point.
c. Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does

not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch. The Power Injector

receives power as soon as AC power is applied. For more information, see

For power adapter (Part Number PWRS-147376-01R) and line cord installations:

a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the

Access Point’s GE1/PoE.
b. Verify the power adapter is correctly rated according the country of operation.
c. Connect the power supply line cord to the power adapter.
d. Attach the power adapter cable to the DC-48V power connector on the Access Point.
e. Attach the power supply line cord to a power supply.

Power Injector System.

5. Verify the behavior of the Access Point LEDs. For more information, see

Configuration

.

Basic Access Point

Installation Guide 15

6. Align the bottom of the ceiling T-bar with the back of the Access Point.

7. Orient the Access Point chassis by its length and the length of the ceiling T-bar.

8. Rotate the Access Point chassis 45 degrees clockwise.

9. Push the back of the Access Point chassis on to the bottom of the ceiling T-bar.

10. Rotate the Access Point chassis 45 degrees counter-clockwise. The clips click as they fasten to the T-bar.

11. Verify the behavior of the Access Point LEDs. For more information, see

LED Indicator.

12. The Access Point is ready to configure. For information on basic Access Point device configuration, see

Basic Access Point Configuration.

16 AP-6521E Series Access Point

!

!

2.6 Above the Ceiling (Plenum) Installation

An above the ceiling installation requires placing the Access Point above a suspended ceiling and installing the
provided light pipe under the ceiling tile for viewing the status LED of the unit. An above the ceiling deployment
enables installations compliant with drop ceilings, suspended ceilings and industry standard tiles from.625 to.75
inches thick.

NOTE The Access Point is Plenum rated to UL2043 and NEC1999 to support

above the ceiling installations. To ensure UL compliance and proper
Access Point operation within the Air Handling Plenum, the Access Point
must be installed with the bottom surface of the unit in contact with the
un-finished surface of the ceiling tile. Placing the product on the ceiling
tile will facilitate the positioning of the light pipe. Placement of the
product in the Air Handling Plenum off of, or away from, the unfinished
surface of the ceiling tile is not UL approved and certification of UL2043
compliance would be void in that case.

CAUTION Do not mount the Access Point directly to suspended ceiling tile with

a thickness less than 12.7mm (0.5in.) or a suspended ceiling tile with
an unsupported span greater than 660mm (26in.).

The mounting hardware required to install the Access Point above a ceiling consists of:

• Light pipe

• Badge for light pipe

• Decal for badge

To install the Access Point above a ceiling:

1. If possible, remove the adjacent ceiling tile from its frame and place it aside.

2. If required, install and attach a security cable to the Access Point’s lock port.

3. Mark a point on the finished side of the tile where the light pipe is to be located.

4. Create a light pipe path hole in the target position on the ceiling tile.

5. Use a drill to make a hole in the tile the approximate size of the Access Point LED light pipe.

CAUTION Take care not to damage the finished surface of the ceiling tile when

creating the light pipe hole and installing the light pipe.

6. Remove the light pipe’s rubber stopper (from the Access Point) before installing the light pipe.

7. Connect the light pipe to the bottom of the Access Point. Align the tabs and rotate approximately 90
degrees. Do not over tighten.

8. Fit the light pipe into hole in the tile from its unfinished side.

Installation Guide 17

!

9. Place the decal on the back of the badge and slide the badge onto the light pipe from the finished side of
the tile.

10. Attach the antennas to their correct connectors.

11. Align the ceiling tile into its former ceiling space.

12. Cable the Access Point using either the Power Injector solution or an approved line cord and power supply.

CAUTION Do not connect to the power source until the cabling of the Access

Point is complete. Ensure PoE is not connected to the Access Point’s
console connector or risk rendering the console connector
permanently inoperable.

For Power Injector installations:

a. Connect an RJ-45 CAT5 Ethernet cable between the network data supply (host) and the Power

Injector’s Data In connector.

b. Connect an RJ-45 CAT5 Ethernet cable between the Power Injector’s Data & Power Out connector

and the Access Point.

c. Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does

not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch. The Power Injector
receives power as soon as AC power is applied. For more information, see

For power adapter (Part Number PWRS-147376-01R) and line cord installations:

a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the

Access Point’s GE1/PoE.
b. Verify the power adapter is correctly rated according the country of operation.
c. Connect the power supply line cord to the power adapter.
d. Attach the power adapter cable to the DC-48V power connector on the Access Point.
e. Attach the power supply line cord to a power supply.

13. Verify the behavior of the Access Point LED light pipe. For more information, see

LED Indicator.

14. Place the ceiling tile back in its frame and verify it is secure.

15. The Access Point is ready to configure. For information on basic Access Point device configuration, see

Basic Access Point Configuration.

Power Injector System.

18 AP-6521E Series Access Point

2.7 LED Indicator

An AP-6521 Series Access Point has a single LED activity indicator on the front of the unit.

The LED provides a status display indicating error conditions, transmission, and network activity for the 5 GHz

802.11a/n (amber) radio or the 2.4 GHz 802.11b/g/n (green) radio.

Task 5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green)

Unadopted Off Blinking 5 times per second

Normal
Operation

Firmware
Update

Locate AP
Mode

• If this radio band is enabled:
Blink at 5 second interval

• If this radio band is disabled:
Off

• If there is activity on this band:
Blink at a 1Hz

On Off

Blink at 5Hz Blink at 5Hz

• If this radio band is enabled:
Blink at 5 second interval

• If this radio band is disabled:
Off

• If there is activity on this band:
Blink at a 1Hz

Installation Guide 19

3 Basic Access Point Configuration

For a WiNG Express SKU (AP-6521E), both the UI and an over the air (OTA) provisioning configuration are required
for a basic setup and network connection. For a non WiNG Express SKU (AP-6521), there’s no OTA support, and the
Access Point utilizes just the UI for its basic setup.

NOTE For information on using WiNG Express beyond this initial setup, refer to

the WiNG Express Users Guide to familiarize yourself with the WiNG
Express Access Point operating system. The guide is available at

www.zebra.com/support

To provide the Access Point a basic configuration and access management functions:

1. Power up the Access Point.
The Access Point can be powered using an appropriately rated power adapter, POE injector or POE switch

resource.

.

2. Connect to the Access Point.

For WiNG Express models

Connect to the WiNG Express SSID. For Windows systems, locate the SSID by selecting the network icon
on the bottom right corner of the screen. For MAC systems, locate the SSID by selecting the network icon
on the top right corner of the screen.

Open a browser (Chrome, Firefox or Internet Explorer) and enter http://express.zebra.com
screen displays.

For non-WiNG Express models:

:

. The login

Refer to the bottom of the Access Point to obtain the numeric IP address used for connecting to the device.
Point the Web browser to the Access Point’s IP address. The login screen displays.

20 AP-6521E Series Access Point

3. Enter the default username admin in the Username field.

4. Enter the default password admin123 in the Password field.

5. Select the Login button to load the management interface.

If this is the first time the WiNG Express interface has been accessed, a screen displays prompting for the
Access Point’s country code.

6. Select the Country Code specific to this Access Point’s deployment location.

Selecting the correct country is central to legal operation. Each country has its own regulatory restrictions
concerning electromagnetic emissions and the maximum RF signal strength that can be transmitted.
Select Apply to implement the selected Country Code. SKU's only support certain countries (for example:
a US SKU only includes US, Guam, Puerto Rico, American Samoa, US Virgin Islands and Mariana Island).

The Access Point automatically displays a Dashboard where users can assess network health and
conduct a diagnostic review of Access Point performance.

NOTE At some point in the Access Point’s initial setup, the default password

should be changed to enhance the security of the Access Point and WiNG
Express managed network. Refer to the Configuration > Management
screen to change the default password to a more secure password.

Installation Guide 21

7. Expand the Configuration menu item and select Basic.

8. Set the following Basic Configuration Settings for this Access Point:

• AP Name - Provide an AP Name used as this Access Point’s WiNG Express network identifier. If
setting this Access Point as a Virtual Controller, each Access Point managed by this Virtual Controller
lists this Access Point’s AP Name as its own. The AP Name is a required parameter.

• Country Code - If the Country Code was not set when the Access Point was initially powered on, set
the country now to ensure the Access Point’s legal operation. The Access Point’s wireless capabilities
are disabled until the required country code is set.

• Virtual Controller -Select this option to define this Access Point as a Virtual Controller capable of
managing and provisioning up to 24 Access Points of the same model. If selecting this Access Point
as a Virtual Controller, those Access Points managed by this Virtual Controller will list this Access
Point’s AP Name as its own. Only one Virtual Controller can be designated.

• Timezone - Use the drop-down menu to specify the geographic timezone where the Access Point is
deployed. Different geographic time zones have daylight savings clock adjustments, so specifying the
timezone correctly is important to account for geographic time changes.

• Date & Time - Set the date, hour and minute for the Access Point’s current system time. Specify
whether the current time is in the AM or PM.

• NTP Server - Optionally provide the IP address of a NTP server resource. Network Time Protocol (NTP)
manages time and/or network clock synchronization within the WiNG Express network. NTP is a
client/server implementation. Access Points (NTP clients) periodically synchronize their clock with a
master clock (an NTP server). For example, an Access Point resets its clock to 07:04:59 upon reading
a time of 07:04:59 from its designated NTP server.

9. Select Apply to implement the updates.

22 AP-6521E Series Access Point

10. Expand the Configuration menu item and select WAN.

11. Refer to the WAN Settings field and set the following:

• Enable - Select this option to allow a connection between the Access Point and a larger network or
outside world through the WAN port. Disable this option to isolate the WAN connection. No
connections to a larger network or Internet are possible. Clients cannot communicate beyond
configured subnets. Both the physical Port used to connect to the WAN and the virtual Interface
(VLAN) are also listed and fixed.

• DHCP Client - Select this option to enable DHCP for the Access Point WAN connection. This is
useful, if the target network or Internet Service Provider (ISP) uses DHCP. DHCP is a protocol that
includes mechanisms for IP address allocation and delivery of host-specific configuration
parameters from a DHCP server to a host. Some of these parameters are IP address, network mask,
and gateway. The WAN and LAN ports should not both be configured as DHCP clients.

• Static IP - Select this option to bypass DHCP address allocation resources and manually set the IP
address for the Access Point’s WAN connection. Manually provide the Access Point’s Static IP/Mask
and Default Gateway.

• PPPoE Settings - Optionally enable Point-to-Point Protocol over Ethernet (PPPoE) on the WAN
network. If PPPoE is enabled, provide the required Auth Type, Login Name and Login Password.
Server Name and Default Gateway are optional settings. PPP is a data-link protocol for dialup
connections allowing an Access Point to use a broadband modem (DSL, cable modem, etc.) for
access to high-speed data and broadband networks. Most DSL providers support (or deploy) the
PPPoE protocol. PPPoE uses standard encryption, authentication, and compression as specified by
the PPPoE protocol. PPPoE enables the Access Point to establish a point-to-point connection to an
ISP over an existing Ethernet interface.

Installation Guide 23

• Static IP / Mask - Specify an IP address for the WAN connection if using static address assignment
for the WAN port. An IP address uses a series of four numbers expressed in dot notation, for
example, 190.188.12.1. Additionally, specify a Mask for the access point’s WAN connection. This
number is available from the ISP for a DSL or cable-modem connection, or from an administrator if
the Access Point connects to a larger network.

• Primary/Secondary DNS/Default Gateway - If using a static IP or DHCP, enter the Primary and
Secondary DNS server resource’s numerical IP address and Default Gateway.

NOTE If segmenting traffic between the Access Point’s WAN and LAN, you’ll

need to create a VLAN. Complete steps 13 and 14 to define the required
VLAN. Otherwise, proceed to step 15.

12. Select Apply to implement the updates.

13. Expand the Configuration menu item and select Access Points. Each AP Name displays as a link that

can be selected to update the configuration of that specific Access Point. Select a target AP Name link
from amongst those displayed in the Access Points screen.

Refer to the LAN IP Interface Settings field, and add a VLAN and Static IP as required for enabling DHCP
(within the Configuration > Services screen) for client IP address requests and ensuring routable traffic.

24 AP-6521E Series Access Point

14. Select Apply to commit the updates to the selected Access Point’s configuration.

15. Expand the Configuration menu item and select Wireless.

The Wireless screen displays fields where Radio Settings and Wireless LAN settings can be defined. It is
recommended default radio settings remain as is for the Access Point’s basic setup. For information on
using WiNG Express beyond this initial setup, refer to the WiNG Express Users Guide. The guide is
available at www.zebra.com/support

.

In respect to the Radio Settings, the professional installer should be aware of the following:

NOTE The above example includes a field for setting the antenna gain. This

setting is only available for external antenna model Access Points and
does not display for internal antenna model Access Points.

• The Channels available for configuration are channels for which the product is approved in its
selected country. The professional installer must ensure the product is set to operate under
conditions, and on channels, approved by country regulations.

• Selecting Smart as the Power setting automatically configures radio power to not exceed the
maximum power allowed by the defined country. For static power settings, the professional installer
must ensure the configured power levels are compliant with local and regional regulations. The
county selected automatically limits the maximum output power that can be set.

• For external antenna model Access Points, configure the Antenna Gain based on the antenna used
in the deployment. The set gain value should include the antenna gain, along with any additional
components, such as extension cables used between the Access Point and the antenna.

In respect to the Wireless LAN settings, the professional installer should be aware WiNG Express
Access Points ship with a default WLAN (WINGExpress). However, this WLAN does not provide adequate
authentication to protect from unauthorized user access. An additional WLAN configuration should be
created and validated before deleting default WLAN.

Installation Guide 25

16. To create a new WLAN, select + Add from the upper, left-hand side of the Wireless LAN field.

17. Set the following configuration attributes for the new WLAN:

• Name - Provide a unique name for the WLAN as its WiNG Express network identifier. This is a
required setting.

• Enable - Select this setting to enable this WLAN within the WiNG Express managed Access Point
network and to provide some measure of data protection not available in the default WLAN.

26 AP-6521E Series Access Point

• SSID - Specify the WLAN's SSID. The WLAN SSID is case sensitive and alphanumeric. SSID length
should not exceed 32 characters. This is a required setting. Select Client-To-Client
Communication to enable client interoperability within this WLAN. The default is disabled,
meaning clients are not allowed to exchange packets with other clients. It does not necessarily
prevent clients on other WLANs from sending packets to this WLAN, but if this setting is disabled
on the other WLAN, clients are not permitted to interoperate at all.

• WLAN Type - The screen displays with the Open option selected. Naming and saving such a policy
(as is) would provide no security and might only make sense in a network wherein no sensitive data
is either transmitted or received. This default setting is not recommended.

If selecting Secure-PSK, enter a WPA2 Key to password protect the WLAN. Define whether the
key is entered in ASCII or HEX characters. Selecting Show to expose the key is not recommended.

If selecting Secure-802.1x, provide an IP address (or hostname) and a shared secret (password)
used to access an external RADIUS server resource designated to validate user requests to the
Access Point’s WLAN resources.

Selecting Guest displays fields for captive portal Web page creation, and is beyond the scope of
this basic WiNG Express Access Point configuration.

• Band -Select the 2.4 GHz and/or 5 GHz radio bands supports by the WiNG Express managed Access
Point and its connected client traffic. If this Access Point is designated as a Virtual Controller AP,
both radio bands should be enabled.

• VLAN - Use the spinner control to specify a VLAN from 1 - 4,094 for this WLAN. When a client
associates with a WLAN, the client is assigned a VLAN by load balance distribution. It is
recommended you do not use VLAN 1 with the WLAN if the WAN port has been enabled.

• Description - Optionally enter a WLAN description to further describe the WLAN’s deployment
objective within the WiNG Express managed network.

18. Select Apply to commit the updates to the Access Point’s WLAN configuration.

Installation Guide 27

19. Expand the Configuration menu item and select Services.

20. Select Enable DHCP Server to ensure the Access Point can provision IP addresses to requesting clients

over the specified interface.

NOTE A VLAN must be already configured and available to the DHCP server as

a viable interface between the Access Point and requesting client. Refer
to the LAN IP Interface Settings field (within the Edit Access Point
screen), and add a VLAN.

Select + Add and provide a starting and ending IP range of addresses that constitute a pool of addresses
available to requesting clients.

21. Select Apply to commit the updates to the Access Point’s DHCP configuration.

22. At this point, you’re ready to connect to the WiNG Express managed network using the security
restrictions applied to the newly created WLAN. Ensure the new secure WLAN has been enabled, and
check whether a client is able to access the WiNG Express network

.

NOTE Only when the new WLAN configuration is validated as accessible

should the existing WiNG Express default WLAN be deleted.

28 AP-6521E Series Access Point

4 Specifications

4.1 Electrical Characteristics

An AP-6521 Series Access Point has the following electrical characteristics:

Max DC Power
Consumption

12.95W (270mA@48V)

4.2 Physical Characteristics

An AP-6521 Series Access Point has the following physical characteristics:

Dimensions 6.0 (Length) x 5.5 (Width) x 1.63 (Tall) - Inches

152.4 (Length) x 139.7 (Width) x 41.1 (Tall) - Millimeters

Housing Plastic

Weight 0.60 lbs/0.272 kg

Operating
Temperature

Storage Temperature -40°F to 158°F/-40°C to 70°C

Operating Humidity 5 to 95% Relative Humidity non-condensing

Storage Humidity 85% Relative Humidity non-condensing

Operating Altitude
(max)

32°F to 104°F/0°C to 40°C

8,000 ft @ 28°C

Storage Altitude
(max)

Electrostatic
Discharge

30,000 ft @ 12°C

+/-15kV Air and +/-8kV Contact @ 50% Relative Humidity

Installation Guide 29

4.3 Radio Characteristics

An AP-6521 Series Access Point has the following radio characteristics:

Operating Channel (2.4 GHz) Channel 1 to 13 (2412 to 2472 MHz)

*Japan Only - Channel 14 (2484 MHz)

Operating Channel (5. GHz) Channels 36 - 165

802.11a Data Rates 6, 9, 12, 18, 24, 36, 48, 54 Mbps

802.11b Data Rates 1, 2, 5.5, 11 Mbps

802.11g Data Rates 6, 9, 12, 18, 24, 36, 48, 54 Mbps

802.11n Data Rates MCS0 to MCS15 at both HT20 and HT40 modes

Max Transmit Power (2.4GHz) 27 dBm

Max Transmit Power (5 GHz) 22 dBm

Transmit Power Adjustment 1 dB

NOTE

Channel 14 is valid only for 802.11b in Japan, 802.11g is not supported.

30 AP-6521E Series Access Point

5 Regulatory Information

5.1 Regulatory Overview

This guide applies to Part Numbers AP-6521-60010-US, AP-6521-60020-US, AP-6521-60010-EU,
AP-6521-60020-EU, AP-6521-60010-WR, AP-6521-60020-WR, AP-6521E-60010-US, AP-6521E-60020-US,
AP-6521E-60010-EU, AP-6521E-60020-EU, AP-6521E-60010-WR and AP-6521E-60020-WR.

AP-6521 Series Access Points are approved under MODEL: NCAP-500.

All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be
labeled as required.

Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user’s authority
to operate the equipment.

Zebra Access Points must be professionally installed and configured so that the Radio Frequency Output Power will
not exceed the maximum allowable limit for the country of operation.

Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or
attachments could cause damage and may violate regulations. Use of an unapproved antenna is illegal under FCC
regulations subjecting the end user to fines and equipment seizure.

5.2 Wireless Device Country Approvals

Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for
use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe.

Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at

www.zebra.com/doc

Note: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden,
Switzerland and the United Kingdom.

Operation of the device without regulatory approval is illegal.

5.2.1 Country Selection – Note for AP & Wireless Controller

Select only the country in which you are using the device. Any other selection will make the operation of this device
illegal. The US version of the Access Point will only have US listed in the country selection table. The US version
will be sold / used in the US protectorates: American Samoa, Guam, Puerto Rico, US Virgin Islands.

Installation Guide 31

5.2.2 Frequency of Operation – FCC and IC

5 GHz Only

The use on UNII (Unlicensed National Information Infrastructure) Band 1 5150-5250 MHz is restricted to indoor use
only, any other use will make the operation of this device illegal.

Industry Canada Statement:

Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful
interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning
they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or
damage to LE-LAN devices.

Avertissement: Le dispositive fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une
utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles
utilisant les mêmes canaux. Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux
(c.-à-d., qu'ils ont la priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer
du brouillage et/ou des dommages aux dispositifs LAN-EL.

2.4 GHz Only

The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited
by firmware.

5.3 Health and Safety Recommendations

5.3.1 Warnings for the use of Wireless Devices

Please observe all

5.3.2 Potentially Hazardous Atmospheres – Fixed Installations

You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc.
and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).

5.3.3 Safety in Hospitals

Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When
installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely
affected.

warning notices with regard to the usage of wireless devices.

Pacemakers

Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld
wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are
consistent with independent research and recommendations by Wireless Technology Research.

32 AP-6521E Series Access Point

Persons with Pacemakers:

• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.

• Should not carry the device in a breast pocket.

• Should use the ear furthest from the pacemaker to minimize the potential for interference.

• If you have any reason to suspect that interference is taking place, turn OFF your device.

Other Medical Devices

Please consult your physician or the manufacturer of the medical device, to determine if the operation of your
wireless product may interfere with the medical device.

5.4 RF Exposure Guidelines

5.4.1 Safety Information

Reducing RF Exposure—Use Properly

Only operate the device in accordance with the instructions supplied.

5.5 International

The device complies with internationally recognized standards covering human exposure to electromagnetic fields
from radio devices. For information on “International” human exposure to eletromagnic fields refer to the
Declaration of Conformity (DoC) at www.zebra.com/doc

.

5.6 EU

Remote and Standalone Antenna Configurations

To comply with EU RF exposure requirements, antennas that are mounted externally at remote locations or
operating near users at stand-alone desktop of similar configurations must operate with a minimum separation
distance of 20 cm from all persons.

5.7 US and Canada

Co-located statement

To comply with FCC RF exposure compliance requirement, the antennas used for this transmitter must not be
co-located or operating in conjunction with any other transmitter/antenna except those already approved in this
filling.

Remote and Standalone Antenna Configurations

To comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or
operating near users at stand-alone desktop of similar configurations must operate with a minimum separation
distance of 20 cm from all persons.

Installation Guide 33

5.8 Power Supply

This device is powered from a 802.3af compliant power source which is UL approved and certified by the
appropriate agencies.

5.9 Radio Frequency Interference Requirements—FCC

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

Restricted Band 5.60 – 5.65 GHz

5.10 Radio Frequency Interference Requirements – Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

5.10.1 Radio Transmitters

For RLAN Devices:

The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:

• Restricted Band 5.60 – 5.65 GHz

L'utilisation de RLAN de 5 GHz, pour utilisation au Canada est soumise aux restrictions suivantes:

• Bande Restreinte de 5,60 à 5,65 GHz

This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de
licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de

34 AP-6521E Series Access Point

brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible
de provoquer un fonctionnement indésirable

Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical
specifications were met.

5.11 CE Marking and European Economic Area (EEA)

The use of 2.4 GHz RLAN’s, for use through the EEA, have the following restrictions:

• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz.

• France, outside usage is restricted to 2.4 – 2.454 GHz.

• Italy requires a user license for outside usage.

5.12 Mexico

"La operación de este equipo está sujeta a lassiguientes dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicialy (2) este equipo o dispositivo debe aceptar cualquierinterferencia,
incluyendo la que pueda causar suoperación no deseada."

5.13 Statement of Compliance

Zebra hereby declares that this device is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from www.zebra.com/doc

.

Installation Guide 35

5.14 Waste Electrical and Electronic Equipment (WEEE)

English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For
information on how to return product, please go to: www.zebra.com/weee

Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Zebra
pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : www.zebra.com/weee

Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo
de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite:

www.zebra.com/weee.

Български: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщат на
Zebra за рециклиране. За информация относно връщането на продукти, моля отидете на адрес:

www.zebra.com/weee

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an
Zebra zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unter

www.zebra.com/weee

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere
restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il
seguente sito Web: www.zebra.com/weee

Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para
reciclagem. Para obter informações sobre como devolver o produto, visite: www.zebra.com/weee.

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te
worden teruggezonden voor recycling. Raadpleeg www.zebra.com/weee
terugzenden van producten.

Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy Zebra w
celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowej

www.zebra.com/weee.

Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti Zebra
k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce: www.zebra.com/weee

Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile.
Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: www.zebra.com/weee

Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás
céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a www.zebra.com/weee
weboldalra.

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för
återvinning. Information om hur du returnerar produkten finns på www.zebra.com/weee

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun
tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa www.zebra.com/weee

Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs
oplysningerne om returnering af produkter på: www.zebra.com/weee.

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται
στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος,
επισκεφθείτε τη διεύθυνση hwww.zebra.com/weee

.

.

.

στο ∆ιαδίκτυο.

.

.

voor meer informatie over het

.

.

.

36 AP-6521E Series Access Point

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati
għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur:

www.zebra.com/weee

Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la
Zebra pentru reciclare. Pentru informaţii despre returnarea produsului, accesaţi: www.zebra.com/weee

Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za
informacije o vračilu izdelka obiščite: www.zebra.com/weee

Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené
spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na: www.zebra.com/weee.

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją
„Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite: www.zebra.com/weee

Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreizējai
pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu, skatiet: www.zebra.com/weee

Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir.
Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin: www.zebra.com/weee.

Turkish WEEE Statement of Compliance

EEE Yönetmeliğine Uygundur

.

.

.

.

.

Installation Guide 37

5.15 Japan (VCCI) - Voluntary Control Council for Interference Class B ITE

この装置は、情報処理装置等電波障害自主規制協議会 （ＶＣＣＩ）の基準に基づくク
ラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としています
が、この装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引
き起こすことがあります。 取扱説明書に従って正しい取り扱いをして下さい。

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may
cause radio interference. Install and use the equipment according to the instruction manual.

5.16 Korea Warning Statement for Class B ITE

기 종 별 사 용 자 안 내 문

B급 기기

( 가정용 방송통신기기 )

Class B (Broadcasting

Communication Device for Home

이 기기는 가정용 (B 급 ) 으로 전자파적합등록을
한 기기로서 주로 가정에서 사용하는 것을 목적

으로 하며 , 모든 지역에서 사용할 수 있습니다 .

This device obtained EMC registration mainly for home use
(Class B) and may be used in all areas.

Use)

5.17 Other Countries

Australia

Use of 5 GHz RLAN’s in Australia is restricted in the following band 5.50 – 5.65 GHz.

Brazil

Regulatory declarations for AP-6521 - BRAZIL

Note: The certification mark applied to the AP-6521 is for Restrict Radiation Equipment. This equipment operates
on a secondary basis and does not have the right for protection against harmful interference from other users
including same equipment types. Also this equipment must not cause interference to systems operating on primary
basis.

For more information consult the website http://www.anatel.gov.br

Declarações Regulamentares para AP-6521 - Brasil

Nota: "A marca de certificação se aplica ao Transceptor, modelo AP-650. Este equipamento opera em caráter
secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo,
e não pode causar interferência a sistemas operando em caráter primário.”

Para maiores informações sobre ANATEL consulte o site: http://www.anatel.gov.br

38 AP-6521E Series Access Point

Chile

“Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a
radiaciones electromagnéticas.”.

"This device complies with the Resolution Not 403 of 2008, of the Undersecretary of telecommunications, relating
to electromagnetic radiation.”

Mexico

Restrict Frequency Range to: 2.450 – 2.4835 GHz.

Taiwan

NOTICE!

According to: Administrative Regulations on Low Power Radio Waves Radiated Devices

Article 12

Without permission granted by the DGT, any company, enterprise, or user is not allowed to change frequency,
enhance transmitting power or alter original characteristic as well as performance to an approved low power
radio-frequency devices.

Article 14

The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If
found, the user shall cease operating immediately until no interference is achieved.

The said legal communications means radio communications is operated in compliance with the
Telecommunications Act.

The low power radio-frequency devices must be susceptible with the interference from legal communications or
ISM radio wave radiated devices. Wireless devices operate in the frequency band of 5.25-5.35 GHz, limited for
Indoor use only.

臺灣

低功率電波輻射性電機管理辦法

第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象
時，應立 ? 停用，? 改善至無干擾時方得繼續使用。
前項合法通信，指依電信規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干
擾。

Installation Guide 39

Wireless devices operate in the frequency band of 5.25-5.35 GHZ, limited for Indoor use.

在 5.25-5.35 赫頻帶內操作之無線資訊傳輸設備，限於室內使用。

Korea

For radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following expressions should be displayed:

1. “This radio equipment cannot provide a service relevant to human life safety, as it can be crossed” through the
user manual, etc.

당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다

2. “This radio equipment cannot provide a service relevant to human life safety, as it can be crossed” through the
user manual, etc.

당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다

40 AP-6521E Series Access Point

6 Support

If you have a problem with your equipment, contact support for your region.

Contact information is available at: www.zebra.com/support

When contacting support, please provide the following information:

• Serial number of the unit

• Model number or product name

• Software type and version number

Support responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements. If you
purchased your product from a business partner, contact that business partner for support.

.

6.1 Customer Support Web Sites

Support located at: www.zebra.com/support provides information and online assistance including developer
tools, software downloads, product manuals and online repair requests.

6.2 Manuals

Documentation is available at: www.zebra.com/support.

Installation Guide 41

15

7 AP-6521 Series Access Point China ROHS Compliance

部件名称

(Parts)

金属部件

(Metal Parts)

电路模块

(Circuit Modules)

电缆及电缆组件

(Cables and Cable Assemblies)

塑料和聚合物部件

(Plastic and Polymeric Parts)

光学和光学组件

(Optics and Optical Components)

电池

(Batteries)

有害物质

铅

(Pb)

OOOO OO

XOOO O O

OOOO OO

OOOO OO

OOOO OO

OOOO OO

汞

(Hg)

镉

(Cd)

六价铬

(Cr(VI))

多溴联

苯

(PBB)

多溴二苯

醚

(PBDE)

本表格依据 SJ/T 11364 的规定编制。
O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量 要求以下。

X: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定 的限量要求。 ( 企业

可在此处，根据实际情况对上表中打 “×” 的技术原因进 行进一步说明。）

This table was created to comply with China RoHS requirements for the AP-6521 Access Point.

42 AP-6521E Series Access Point

Zebra Technologies Corporation
Lincolnshire, IL 60069 USA

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered
trademark of Symbol Technologies, Inc., a Zebra Technologies company.

MN001366A01 Revision B April 2015