Zamel VP-819B, VP-819W Operating Manual
VIDEO ENTRY PHONE DISPLAY
VP-819B / VP-819W
Thank you for buying this product from Zamel.
Zamel shall not accept any liability for any results of damage
and / or accidents caused by non-intended use of the product.
Before attempting to install this product, please read and understand
the entire Operating Manual to comply with the intended use.
Do not open or tamper with the product without prior authorization.
Otherwise your warranty rights for this product will be void.
2
SAFETY
• Always follow this Manual for your safety and to prevent damage to the product.
• Do not connect more than one load to a single power outlet at a time. Risk
of overheating the wiring or re!
• Do not connect or interface this device with incompatible products. Otherwise
there is a risk of an electrical short circuit, resulting in damage to this product.
• Protect the display main board and screen from deformation by any stress.
Do not apply heavy loads. Otherwise there is a risk of re.
• Do not clean the display screen or housing with water or detergents. Risk
of damage to the display housing and/or screen, electrical short circuit, and/or
re! Clean the display with a soft, dry cloth made of cotton or microbre. This will
prevent scratching the display screen. Never use toilet paper or tissues.
• Do not install in a highly humid indoor environment. Risk of electrical short circuit
and re!
• Disconnect the power cord from the mains by holding the plug and not the cable.
Damage to the power cord cable may result in an electric short circuit or a re.
• Do not plug the power cord into the mains with wet hands. Electrocution hazard!
• Do not attempt to disassemble, repair or alter this product on your own. Risk
of electrocution, damage to the product and/or re!
• Do not install a current breaker on the mains connection of the device.
Electrocution hazard!
PRODUCT DESCRIPTION
• 7” colour LCD touch screen
• 4-core wiring
• Intuitive interface
• Internal calls (display-to-display
intercom mode)
• Public Address mode
• Gate and wicket opening control
• Supports up to two CCTV feeds
• Supports up to two entrance panels
• On-demand video feed monitoring
from entrance panels and all
• connected CCTV cameras
• Two-way voice communication
• High display screen resolution:
800 x 480
• Clear voice handset-free device
• Language selection
• Intuitive buttons
• 10-step voice volume control
• 10-step brightness, contrast
and saturation control
• 10-step ringtone volume control
• 12 polyphonic ringtones
TECHNICAL DATA
• Operating temperature: -30°C to +60°C
• Supply voltage: 110-240 V AC
/ 50-60 Hz; 14.5 V DC / 0.8 A
• Power input: 7 W (max); 0.7 W
(standby)
• Operating RH: 0% to 95%
• Display dimensions: 208 x 115 x 25 mm
• Weight: 430 g
WIRING PROFILE
• ≤ 50 m (4 x 0.5 mm2)
• ≤ 75 m (4 x 0.75 mm2)
• ≤ 100 m (4 x 1.0 mm2)
PRODUCT COMPONENTS
• 1 x Display unit
• 1 x Operating Manual
• 1 x Base stand
• 2 x Wall plugs
• 2 x M4 x 30 screws
• 2 x 5-pin male connector
• 1 x 4-pin male connector
• 1 x 4-pin male connector
3
WIRING CONNECTION DIAGRAM
AD: Audio
VD: Video
PWR: Power
GND: Ground
DATA: Data communication
CCTV: CCTV feed in
KEY1/KEY2: Control voltage
J4
J4
J4
J4
ROOM 1
ROOM 2
ROOM 3
ROOM 4
ELECTRIC
CATCH 2
ELECTRIC
CATCH 1
DISPLAY 1
DISPLAY 2
4
Note:
(a) Wiring connection diagram for an entrance panel with electric catch no. 2 + extra external
power supply.
(b) Wiring connection diagram for electric catch no. 1 with the display output power
(GND and KEY1 contacts).
(c) External power supply port J4 (optional)
(d) Wiring connection diagram for the NC06 gate control module (Connector P3 GND
and DATA to NC06; COM NO/NC to gate control)
AD: Audio
VD: Video
PWR: Power
GND: Ground
DATA: Data communication
CCTV: CCTV feed in
KEY1/KEY2: Control voltage
J4
J4
J4
J4
BLUE
YELLOW
WHITE
RED
ROOM 1
ROOM 2
ROOM 3
ROOM 4
ELECTRIC
CATCH 1
DISPLAY 1
Loading...