Zamel VP-809W, VP-809B Operating Manual

VIDEO ENTRY PHONE DISPLAY

VP-809B / VP-809W

Thank you for buying this product from Zamel.
Zamel shall not accept any liability for any results of damage and/or accidents
caused by non-intended use of the product.
Before attempting installation of this product, please read and understand the entire
Operating Manual to comply with the intended use.
Do not open or tamper with the product without prior authorization.
Otherwise your warranty rights for this product will be void.

2

SAFETY

• Always follow this Manual for your safety and to prevent damage to the product.

• Do not connect more than one load to a single power outlet at a time. Risk

of overheating the wiring or re!

• Do not connect or interface this device with incompatible products. Otherwise
there is a risk of an electrical short circuit, resulting in damage to this product.

• Protect the display main board and screen from deformation by any stress.

Do not apply heavy loads. Otherwise there is a risk of re.

• Do not clean the display screen or housing with water or detergents. Risk

of damage to the display housing and/or screen, electrical short circuit, and/or re!
Clean the display with a soft, dry cloth made of cotton or microbre.

This will prevent scratching of the display screen. Never use toilet paper
or tissues.

• Do not install in a highly humid indoor environment. Risk of electrical short circuit

and re!

• Disconnect the power cord from the mains by holding the plug and not the cable.

Damage to the power cord cable may result in an electric short circuit or a re.

• Do not plug the power cord to the mains with wet hands. Electrocution hazard!

• Do not attempt to disassemble, repair or alter this product on your own. Risk

of electrocution, damage to the product and/or re!

• Do not install a current breaker on the mains connection of the device.

Electrocution hazard!

PRODUCT DESCRIPTION

• 7” colour LCD touch screen

• 4-core wiring

• Intuitive interface

• Digital audio and video recorder (DVR)

• Internal calls (display-to-display intercom mode)

• Public Address mode

• Gate and wicket opening control

• Supports up to two CCTV feeds

• Supports up to two entrance panels

• Calendar mode

• Alarm clock

• Digital photo frame mode

• Media player

• Internal memory for up to 90 digital photos

• microSD card reader: supports up to 32 GB storage

• Gate entrance panel video feed recording and manual camera snapshot
functionality

• Leave Message (voice recorder) mode

• Automatic gate entrance panel camera snapshot at each Call button press

• Motion detection and automatic video feed sequence recording

• Automatic Away-from-Home Reply mode

3

• On-demand video feed monitoring from entrance panels
and all connected CCTV cameras

• Two-way voice communication

• High display screen resolution: 800 x 480

• Clear voice handset-free device

• 10-step voice volume control

• 10-step brightness, contrast and saturation control

• 10-step ringtone volume control

• 13 polyphonic ringtones

• Additional ringtones available from a microSD card

TECHNICAL DATA

• Operating temperature: -30°C to +60°C

• Supply voltage: 110-240 V AC / 50-60 Hz; 14.5 V DC / 0.8 A

• Power input: 9 W (max); 0.7 W (standby)

• Operating RH: 0% to 95%

• Maximum connection wiring length: 100 m

• Display dimensions: 186 x 127 x 15 mm

• Weight: 420 g

WIRING PROFILE

• ≤ 50 m (4 x 0.5 mm2)

• ≤ 75 m (4 x 0.75 mm2)

• ≤ 100 m (4 x 1.0 mm2)

PRODUCT COMPONENTS

• 1 x Display unit

• 1 x Operating Manual

• 1 x Base stand

• 2 x Wall plugs

• 2 x M4 x 30 screws

• 2 x 5-pin male connector

• 1 x 4-pin male connector

• 1 x 4-pin male connector

4

WIRING CONNECTION DIAGRAM

AD: Audio
VD: Video
PWR: Power
GND: Ground
DATA: Data communication
CCTV: CCTV feed in
KEY1/KEY2: Control voltage

a b

ROOM 1

ROOM 2

ROOM 3

ROOM 4

ELECTRIC
CATCH 2

ELECTRIC
CATCH 1

J4

J4

J4

J4

DISPLAY 1

DISPLAY 2

5

Note:
(a) Wiring connection diagram for an entrance panel with electric catch

no. 2 + extra external power supply.

(b) Wiring connection diagram for electric catch no. 1 with the display

output power (GND and KEY1 contacts).
(c) External power supply port J4 (optional)
(d) Wiring connection diagram for the NC06 gate control module

(Connector P3 GND and DATA to NC06; COM NO/NC to gate control)

AD: Audio
VD: Video
PWR: Power
GND: Ground
DATA: Data communication
CCTV: CCTV feed in
KEY1/KEY2: Control voltage

b

BLUE
YELLOW

WHITE
RED

J4

J4

J4

J4

ROOM 1

ROOM 2

ROOM 3

ROOM 4

ELECTRIC
CATCH 1

DISPLAY 1

6

• The second and each additional display may only output the video feeds from

the cameras to which they are connected.

• All displays can output the video feed of a CCTV camera connected

to the entrance panel port.

AD: Audio
VD: Video
PWR: Power
GND: Ground
DATA: Data communication
CCTV: CCTV feed in
KEY1/KEY2: Control voltage

J4

J4

J4

J4

ROOM 1

ROOM 2

ROOM 3

ROOM 4

DISPLAY 1

7

SYSTEM CONFIGURATION

The system can be installed in one of the congurations shown in the diagrams below:

• 2 gate entrance panels + 4 displays + 2 CCTV cameras for each display

• 1 gate entrance panel + 1 CCTV camera + 4 displays + 2 CCTV cameras for each

display

MAIN DISPLAY

DOOR 1

DOOR 2

DISPLAY 2 DISPLAY 3 DISPLAY 4

CAMERA 1 CAMERA 1 CAMERA 1 CAMERA 1

CAMERA 2 CAMERA 2 CAMERA 2 CAMERA 2

MAIN DISPLAY

CAMERA 3

DOOR 1

DISPLAY 2 DISPLAY 3 DISPLAY 4

CAMERA 1 CAMERA 1 CAMERA 1 CAMERA 1

CAMERA 2 CAMERA 2 CAMERA 2 CAMERA 2

8

PRODUCT DESCRIPTION

1. Power LED

2. LCD panel

3. Back / End Call / Main Menu button

4. Microphone

5. Power On/Off switch

6. microSD card slot (32 GB max.)

INSTALLING THE SYSTEM

1. Use the wiring connection diagram for the chosen system conguration

and verify that all wiring connections are correct.

2. Choose a suitable location in which to install the display unit. An installation

height between 1.5 and 1.6 m above the ground is recommended.

3. Verify that the power supply voltage is OFF before wiring the device.

4. Mount the back frame on the wall at the installation location.

5. Connect the wiring to the terminals, see the wiring connection diagram

for the chosen system conguration.

6. Install the display unit on the back frame.

7. Switch on the supply voltage of the device when completely installed.

1

2

3 4

5

6



150 cm

9

WIRING SPECIFICATIONS

The system supports two electric catch release congurations: with the open

command output by (i) an entrance panel or (ii) a system display (the display
open command output wire must have the shield connected to earth). If the open

command is output by an entrance panel, use this wiring specication:

• If the entrance panel is < 30 m away from the video entry phone display,

use YTDYw 4 x 0.5 mm

2

wiring.

• If the entrance panel is > 30 m away from the video entry phone display,

use YTDYw 4 x 0.5 mm

2

wiring.

If the open command is output by a display, use this wiring specication:

• If the entrance panel is < 30 m away from the video entry phone display,

use YTDYw 6 x 0.5 mm2 wiring.

• If the entrance panel is > 30 m away from the video entry phone display,

use YTDYw 6 x 0.8 mm

2

wiring.

RED
BLUE
YELLOW
WHITE

1
2
3
4

1
2
3
4

RED
BLUE
YELLOW
WHITE

GREEN

BROWN

ELECTRIC

CATCH

ENTRANCE PANEL

RED
BLUE
YELLOW
WHITE

1
2
3
4

1
2
3
4

RED
BLUE
YELLOW
WHITE

GREEN

BRAUN

ELECTRIC

CATCH

ENTRANCE PANEL

ENTRANCE PANEL

ELECTRIC CATCH

BLACK
GREEN

RED
BLUE
YELLOW
WHITE

RED
BLUE
YELLOW
WHITE
BRAUN

ENTRANCE PANEL

ELECTRIC CATCH

BLACK
GREEN

RED
BLUE
YELLOW
WHITE

RED
BLUE

YELLOW
WHITE
BRAUN

GREEN

GREEN

DISPLAY

DISPLAY

DISPLAY

DISPLAY

10

MENU OVERVIEW

When the display in in the sleep mode, press to open the menu shown below:

Item Icon Function Note

1

Call other displays / answer the entrance
panel call

2

Record an out-of-home reply message

3

Listening mode

4

Entrance panel / CCTV video feed display

5

Public Address mode

6

Settings

7

Browse and play back DVR les

Touch

to delete a le. Touch to open

the sound settings.

8

Browse and play back media les

Touch

to delete a le. Touch to open

the sound settings.

9

Time and calendar display

10

Browse and play back audio les

Touch

to delete a le. Touch to open
the sound settings. Touch to open the voice
message tone settings.

11

Display snapshots captured by the gate
entrance panel

Touch

to delete a le.

12

Browse and play back extra photos

Touch

to delete a le.

Note:

Swipe your nger left / right on the touch screen to browse the les back / forward.
Swipe your nger up to go back to the previous menu. Swipe your nger down
to adjust volume. Swiping your nger up / down in a le browsing menu scrolls

the screen pages back / forward.
Function items 2, 7, 8, 10, 11, and 12 require a microSD (max. 32 GB) card installed
in the display.

11

ANSWERING AN ENTRANCE PANEL CALL

When a visitor presses the Call button on the entrance panel, all connected indoor
displays will sound the call chime at the same time with the INCOMING CALL
message on each display screen.

Touch the

icon to answer the call. Touch the icon to output the calling entrance

panel camera feed on all other displays.

terminates the call. If the call is not answered by the time the call chime stops,

the display will enter the standby mode. Touch the

icon to release the electric catch

of the calling entrance panel during the call. The display will show DOOR OPEN. Touch

the

icon to open the gate. The display will show GATE OPEN. If another call

is coming in during your call, the display will show VISITOR AT DOOR 2. Touch

the

icon to answer and switch to the second call.

Note: Touch the

icon during an entrance call or an internal call (display-to-display

intercom mode) to mute your microphone. The display will show MUTE

. Touch

again to unmute your microphone, which the display will conrm with SPEAK

.

Operating a gate requires the NC06 gate control module in the system.

VIDEO FEED MONITORING

With the display on standby, touch to monitor the video feed from entrance panel 1.

Touch

again to switch to the next video feed.

The CCTV camera video feeds can only be monitored this way if the Port 4 status

is Enabled (see Table SYSTEM SETTINGS, item 5). Touch

to start a voice call with

the visitor at the entrance panel you are monitoring the video feed from. Touch

to unlock the door of the same entrance panel. Touch

to unlock the gate

of the same entrance panel.

When monitoring the video feed from Door1/Door2/CCTV1/CCTV2, touch and hold

or swipe your nger left or right on the screen to change the screen aspect from 16:9

to 4:3.

INCOMING CALL

12

PUBLIC ADDRESS MODE

The Public Address mode allows you to speak through all displays connected

to the video entry phone system. When the display is on standby, touch and hold
on the screen. The PUBLIC ADDRESS CALL message will be displayed. All other
displays in the system will display PUBLIC ADDRESS. You can now speak and
be received by other displays in the system.

INTERNAL CALLS (DISPLAY-TO-DISPLAY INTERCOM MODE)

The intercom mode allows two-way voice calls between two specic displays

in the video entry phone system. Touch

on the display on standby to call another

display in the system. If you have more than 2 displays in the video entry phone

system, choose the display you wish to call. Touch to answer an intercom mode

call. Touching

/ /

,

rejects an incoming intercom mode call or terminates

the intercom mode call in progress.

MULTIMEDIA

allows uploading of custom music les and voice messages.

CALENDAR

displays the time and the calendar.

MESSAGES

displays the last events logged by the system.

PHOTOS

is the digital photo frame mode, which displays the photos you have uploaded.

DISPLAY BRIGHTNESS / COLOUR / CONTRAST
/ ZOOM CONTROL

Touch

in the monitoring, incoming call, voice call, intercom, or public address
mode to open the display control screen and choose the desired control function icon
in the left part of the screen.

Icon Function

Colour

Brightness

Contrast

Voice

FunkcjaIkona

Kolor
Jasność
Kontrast
Głos

13

DO NOT DISTURB MODE

You can enable or disable the DO NOT DISTURB mode in the display System
Settings menu.

DISPLAY MONITORING

With the display on standby, touch and hold

to start listening through the
microphone of another display in the voice entry phone system. If you have more than
2 displays in the video entry phone system, choose the display to which you wish
to listen.

Note:
a) The user of the display that is listening will hear everything that the microphone

of the display being listened to captures. The display being listened to will not
output the sounds captured by the microphone of the display which is listening.

b) If you have more than 2 displays in the video entry phone system, verify that

the remote listening mode is enabled in the display to which you want to listen.
Go to System Settings and verify that Can Be Monitored is set to Enable.

MANUAL AUDIO RECORDING

Touch on the main screen to record an audio sequence. Touch again to stop
recording.

SNAPSHOT CAPTURE AND MANUAL VIDEO FEED
RECORDING

Manual snapshot capture: Touch when displaying a video feed from an entrance
panel or monitoring a video feed. A snapshot of the video frame will be captured.
The display will show the message IMAGE CAPTURED.
Manual video feed recording: Touch

when answering a call or monitoring
a video feed. The display will start recording the video feed and display the message
RECORDING. Touch

again to stop recording.
Automatic capture: To have the display automatically capture snapshots,
set the AUTO CAPTURE QUANTITY
in the System Settings to 1, 2 or 3. The display system will then capture and save
the set number of video snapshots to the microSD card when a call is made with
an entrance panel.

14

SYSTEM SETTINGS

With the display on standby, touch and open the System Settings menu .

LEAVE MESSAGE MODE

The mode allows each visitor to leave a voice message with the entrance panel when
no one answers the call. Activate the mode by setting AUTO LEAVING MESSAGE
to Enable in the System Settings. When the Leave Message mode is active,
the caller at an entrance panel will hear a recorded Away-from-Home Reply if they
press the Call button and the call chime ends unanswered. The Away-from-Home
Reply playback will end with a tone, after which the visitor may leave a voice
message. The voice message recording time is limited to 20 seconds. The entrance
panel will revert to the standby mode after this time has counted down. The default
Away-from-Home Reply can be replaced with a custom one you can record
on the microSD card.

15

Item System functions Options Note

1 LANGUAGE

Selects the
display interface
language.

Choose the language:
PL, EN, DE, FR, RU

2 DO NOT DISTURB

ENABLE The LED will ash if this mode is enabled.

DISABLE

The mode is disabled by default during
a call from an entrance panel,
display-to-display intercom (internal)
calls and the public address mode.

3 CAN BE MONITORED

ENABLE

This display can be monitored (listened
to) by other displays in the video entry
phone system if this option is set
to ENABLE.

DISABLE The mode is disabled by default.

4 MONITOR UNLOCK

ENABLE

Touch

to unlock the electric catch

linked to the entrance panel. Touch
to open the gate linked to the entrance
panel.

DISABLE

When this function is disabled, touching

followed by / will open
the door or the gate linked to the
entrance panel.

5 PORT STATE None / CCTV1 / CCTV1&2

6 DEVICE ADDRESS Room 1 / 2 / 3 / 4

Choose ROOM 1 on the display that
should be the main (master) display
of the system. The setting will be yellow
if the same device address is set in two
displays in the video entry phone system.

7 RESTORE DEFAULT ENTER

Restores the default factory settings
of this display.

8 FORMAT FLASH ENTER

Formats the embedded ash memory

of this display.

9 FORMAT SD CARD ENTER

Formats the microSD card installed
in the display.

10 COPY FILE TO SD CARD ENTER

Copies all les from the embedded
ash memory to the microSD card

in the display.

11 AUTO CAPTURE QUANTITY 01, 02, 03

Automatically captures 1, 2 or 3 video
feed snapshots during a call from
an entrance panel.

12 AUTO LEAVING MESSAGE

ENABLE

The visitor calling with an entrance
panel can leave a voice message after
the Away-from-Home Reply and tone.

DISABLE Disables this mode.

13 SCREENSAVER TIME 30 s, 1-3 min, 5, 10, 20, 30, 40, 50, 60 min

14 FIRMWARE VERSION

Displays the version of the rmware

installed on the display.

Switch the option setting with .

16

DVR (DIGITAL VIDEO RECORDER)

Start the DVR mode by touching . Touch

and

to open the DVR mode

settings.

Automatic DVR operation:

Set DVR to Enable in the System Settings. DVR can record video sequences
from each entrance panel and CCTV camera connected to the video entry
phone system.
If motion detection is enabled, the system will automatically record a video
sequence up to 7 minutes long in a cycle mode. The cycles of video sequence
recording are 1 minute + 1 minute + 5 minutes. If a camera detects movement

in its eld of view, its video feed will be recorded for 1 minute. Next, the video

feed is again scanned for motion. If there is no motion detected, the video feed
recording stops. If there is motion detected, the video feed will be recorded for
another 1 minute. Next, the video feed is again scanned for motion. If there
is no motion detected, the video feed recording stops. If there is motion
detected, the video feed will be recorded for another 5 minutes and
the recording then stops.

DVR will not work if the microSD card in the display has less than 2 GB capacity.
The minimum recommended capacity of the microSD card is 8 GB for the DVR
to work smoothly. Set the Resolution to 640x480 for a high video quality.
If the Begin and End Times have the same setting values, DVR will record
without interruption.

17

VIDEO SNAPSHOT CAPTURE SETTINGS

Functions:

Storage type Resolution Number of snapshots

Embedded ash memory

640 x 480 / 320 x 240,
as set in Resolution

100 snapshots max.

microSD card

640 x 480 / 320 x 240,
as set in Resolution

Depends on the microSD card
capacity

DVR RECORDING SETTINGS

Functions:

microSD card capacity Resolution Frame rate

2 GB – 32 GB

640 x 480 / 320 x 240,
as set in Resolution

2 / 4 / 6 / 8 / 10, as set in Frame
Rate

DVR SETTINGS

Item Settings Options Note

1 DVR

Enable DVR is enabled.

Disable The function is disabled.

2 FRAME RATE

2 / 4 / 6 / 8 / 10
frame/s

3 RESOLUTION 640 x 480 / 320 x 240

4

MOTION DETECT
SENSITIVITY

High / Normal / Low

Detects motion in the camera
FOV according to a pre-set
sensitivity.

Disable No motion is detected.

5 BEGIN TIME The time the DVR starts recording and detecting motion.

6 END TIME The time the DVR stops recording and detecting motion.

7 RECORD LOCATION

DOOR 1 / DOOR 2
/ CCTV1 / CCTV2

The video feed and motion
detection signal source
for the DVR.

Switch the option setting with .

18

ALARM CLOCK

Touch in the main menu. Next, touch

.

Opcje

Uwagi

Włączony Aktywuje funkcję DVR
Wyłączony

2 / 4 / 6 / 8 / 10 ramek

640x480 / 320x240
Wysoki / Normalny /

Niski
Wyłączony

Nie wykrywa ruchu.

Początek czasu nagrywania DVR oraz wykrywania ruchu

Koniec czasu nagrywania DVR oraz wykrywania ruchu

DRZWI 1 / DRZWI 2 /
CCTV1 / CCTV2

Miejsce nagrywania DVR oraz detekcji
ruchu

Deaktywuje funkcję

Wykrywa ruchy przy założeniu jednego z
profili.

Item. Settings Options Note

1

SYSTEM TIME
SETTING

Hour / Minutes / Seconds

2

SYSTEM DATE
SETTING

Day / Month / Year

3 ALARM RING TYPE 01 – 13

4

ALARM CLOCK
1 / 2 / 3 / 4

DISABLE

ALWAYS ACTIVE

Rings the alarm every day
for 1 minute at the pre-set
time.

ACTIVE ON SPECIFIC
DAYS

Rings the alarm for
1 minute at the pre-set time

on the specic days set.

Switch the option setting with .

19

CHIME SETTINGS

Touch in the main menu. Next, touch .

Opcje

Uwagi

Dzień/Miesiąc/Rok

01 - 13

WYŁĄCZONY

ALARMUJE KAŻDEGO DNIA
PRZEZ 1 MINUTĘ O USTAWIONEJ
GODZINIE

ZAWSZE AKTYWNY

ALARMUJE W USTAWIONE DNI
PRZEZ 1 MINUTĘ O USTAWIONEJ
GODZINIE

Godzina/Minuta/
Sekunda

AKTYWNY W
OKREŚLONE DNI

Item. Settings Options Note

1 CHIME TIME

0, 15, 20, 25, 30, 35, 40, 45,
50, 55, 60 s

The chime will stop after
the time set here.

2 CHIME VOLUME 00 – 99

00 - Chime muted
09 - Highest chime volume

3 RING TYPE

DOOR 1 / DOOR 2
/ INTERCOM

01 – 13

4 RING REPEAT

ENABLE

The ringtone will sound
repeatedly for a pre-set time.

DISABLE

The ringtone will sound
once.

5 NIGHT MODE

00 – 05

The ringtone will
be automatically muted
between 22:00 and 07:00.

DISABLE

Switch the option setting with .

20

ADVANCED SETTINGS

The Advanced Settings can be accessed by pressing and holding the Main Menu
button while powering on the display. The Advances Settings include:

• Door unlock time
1-10; 20, 30, 40, 50, 60, 70, 80, 90, 99 s

• Gate status
Normally open electric catch contact (NO)
Normally closed electric catch contact (NC)

• Gate unlock time

0.2, 0.5, 1-5 s

• System type
Single-family
Multi-family

The System Type setting applies to the P1 connector of the display linked to Door 1.

WARRANTY

24-month commercial warranty by the manufacturer

Reseller’s stamp and signature

with date of sale

1. ZAMEL Sp. z o.o. Gives a 24-month warranty for
the goods it sells.

2. The warranty given by ZAMEL Sp. z o.o. does not cover:
a) mechanical damage caused by transport,
loading/unloading or other circumstances;
b) damage caused by improper installation or operation
of the goods manufactured by ZAMEL Sp. z o.o.;

c) damage caused by any modications made by the BUYER

or any third party to the sold goods or to the equipment
required for the proper functioning of the sold goods;
d) damage caused by any force majeure
event or another fortuitous event beyond
any reasonable control of ZAMEL Sp. z o.o.;
e) the power supply (batteries) included (if any) with the
device as sold.

3. The BUYER shall make all warranty claims in writing at the point of sale or to ZAMEL Sp. z o.o.

4. ZAMEL Sp. z o.o. will examine each warranty claim as regulated by the applicable provisions of the Polish law.

5. The form of warranty claim resolution, i.e. replacement, repair or refund of the price of purchase, shall
be decided by ZAMEL Sp. z o.o.

6. This warranty does not exclude, limit or suspend any rights of the BUYER arising from the statutory
or regulatory laws concerning implied warranty for defects of sold goods.