Zamel PBM-01 Instruction Manual

BISTABLE RELAY PBM-01 INSTRUCTION MANUAL

Zakład Mechaniki i Elektroniki

ZAMEL sp.j.

J.W. Dzida, K. Łodzińska

ul. Zielona 27, 43-200 Pszczyna, Poland

Tel. [phone], Fax [phone]

www.zamelcet.com, e-mail: [e-mail]

DESCRIPTION

The bistable relay PBM-01 is used to
control lighting or other devices by me­ans of monomodular pushbuttons con­nected in a parallel way. Pushing any
button causes switching on or switching
off the devices connected to output termi­nals. Using this system gives the possibi­lity of creating “intelligent” lighting control
systems.

FEATURES

● Bistable lighting control Input rated in-

dicator – LED green,

● relay mode indicator – LED red,

● system releasing from the L or N ca-

ble,

● cooperation with monostable push-

buttons equipped with illumination

lamps,

● TEST function,

● double-wire controll installation,

● voltage relay output - one NO (normal

closed) contact max 16 A capacity

● monomodular casing TH-35 DIN rail

installation.

TECHNICAL DATA

Input (supply) terminals: L, N

Input voltage tolerance: -15 ÷ +10 %

Rated power consumption: 24 mA

Supply voltage control indicator: LED green

Release control current: 930 μA

Power/relay supply indicator: LED red

Relay operating indicator: TEST button

Output relay parameters: 1NO - 16 A / 250 V AC1 4000 VA

Number of terminal clamps: 8

Section of connecting cables: 0,2 ÷ 2,50 mm

Ambient temperature range: -20 ÷ +45 oC

Overvoltage category: II

Reference standards: PN-EN 60669-1; PN-EN 60669-2-1

PBM-01

Input rated voltage: 230 V~

Nominal frequency: 50 / 60 Hz

Release terminals: IN, IN, IN

2

Operating position: freely

Mounting: rail TH 35 (PN-EN 60715)

Protection degree: IP20 (PN-EN 60529)

Protection level: II

Pollution degree: 2

Napięcie udarowe:

Dimensions: monomodular (17,5 mm) 90x17,5x66 mm

1 kV (PN-EN 61000-4-5)

Weight: 78 g

PN-EN 61000-4-2,3,4,5,6,11

The device is designed for
single-phase installation and
must be installed in accor­dance with standards valid
in a particular country. The

CAUTION

device should be connected

according to the details inc­luded in this operating manual. Installation,
connection and control should be carried
out by a qualifi ed electrician staff, who act
in accordance with the service manual and
the device functions. Disassembling of the
device is equal with a loss of guarantee
and can cause electric shock. Before in­stallation make sure the connection cables
are not under voltage. The cruciform head
screwdriver 3,5 mm should be used to in­stal the device. Improper transport, storage,
and use of the device infl uence its wrong
functioning.
It is not advisable to instal the device in the
following cases: if any device part is missing
or the device is damaged or deformed. In
case of improper functioning of the device
contact the producer.

The symbol means selective
collecting of electrical and electronical
equipment. It is forbidden to put
the used equipment together
with other waste

APPEARANCE

Input supply terminal (L) Input supply terminal (N)

Release terminals

(IN, IN, IN)

Supply voltage control indicator

Power/relay supply indicator

Relay test

Output (load)

relay terminals (11, 11, 14)

VER. 001_03.11.2009

MOUNTING, FUNCTIONING

CONNECTION

INNER DIAGRAM

1. Disconnect the power supply from the

mains by the phase fuse, the circuit­breaker or the switch-disconnector
that are joined to the proper circuit,

2. Check if there is no voltage on con-

nection cables by means of a spe­cial measure equipment,

3. Install PBM-01 device in the switch-

board on TH-35 DIN rail,

4. Connect the cables with the terminals

according to installing diagram,

5. Switch on the power supply from the

mains,

6. Push the TEST button several times

to check the relay operation correct­ness.

The device is ready to work after
switching on power supply. The relay
operation correctness can be checked
by pushing the TEST button placed
on the front panel. The system should
switch on and off the load connected to
its output terminals. Mono modular pu­shbuttons can be connected in a paralell
way which enables the lighting control
from different places. Lighted pushbut­tons version is possible.

DIMENSIONS

APPLICATION

L N

IN
IN
IN

T

11 1411

TIME COURSE

U

IN

RELAY CAPACITY

t

t

t

PRODUCT FAMILY

The time relay PBM-01 belongs to PBM
time relay product family.

Supply version:
24V - 24V AC/DC available for

PBM-01, PBM-02, PBM-03,

12-24V- 12÷24V AC/DC available for

PBM-05

U - universal supplying voltage

12÷230V AC/DC

Device version:
01 - basic
02 - extended: SET, RESET functions

and state storage
03 - with time limit function
04 - zero current consumption with

time limit function
05 - zero current consumption, SET,

RESET functions and time limit

function

Casing type:
M - modular version (TH 35 DIN rail)
P - fl ush junction box Ø60 version

Device type

WARRANTY CARD

There is 24 months guarantee on the product

Salesman stamp and signature, date of sale

LOCAL

CONTROL

CENTRAL RESET

BISTABLE RELAYS

Typical use:

The bistable relay operating the stair­case lighting (e.g. indoor lighting) are con­trolled by means of mono modular push­buttons that can be connected in a parallel
way. The buttons can be placed in different places which gives the possibility of creating universal
lighting systems control. The bistable relay cooperates with time relay PCM-04 (with set-ups:
MODE=F, TIME=3, RANGE=2) and the same gives additional function of the central bistable
relay switch off (reset) by momentary power cut.

Signal separator coordination SEM-01:

In the bistable control systems signal separators can be used to divide control signals into
particular relay groups.

1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product.

2. The manufacturer’s guarantee does not cover any of the following actions:
a) mechanical damage during transport, loading / unloading or under other circumstances,
b) damage caused by incorrect product mounting or misuse,
c) damage caused by unauthorised modifi cations made by the PURCHASER or any third parties to the product or any other devices

needed for the product functioning,

d) damage caused by Act of God or any other incidents independent of the manufacturer.

3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J.

4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation.

5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return.

6. The manufacturer’s guarantee is valid in the Republic of Poland.

7. The PURCHASER’s statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or

otherwise are not affected by this warranty.

VER. 001_03.11.2009