Zamel ASP-02 User guide

STAIRCASE LIGHTING TIMERy ASP-02 INSTRUCTION MANUAL

Zakład Mechaniki i Elektroniki

ZAMEL sp.j.

J.W. Dzida, K. Łodzińska

ul. Zielona 27, 43-200 Pszczyna, Poland

Tel. [phone], Fax [phone]

www.zamelcet.com, e-mail: [e-mail]

DESCRIPTION

The ASP-02 staircase timer is desi­gned for corridor and staircase lighting
control. After the circuit triggering the
timer keeps the light ON for the preset
time and then switches it OFF. It has an
adjustable ON-time setting of 10 seconds
to 14 minutes. ON-time may be adjusted
by means of a potentiometer. The timer is
fitted with a counter-interlock circuit. The
ASP-02 staircase timer may by applied
as a time relay for delayed switch-OFF.
It is possible to mount the device under a
push button, in a deep junction box of 60
mm diameter.

FEATURES

ی Staircase lighting control,
ی Continuous ON-time adjustment of 10

seconds to 14 minutes,
ی Relay state indicator – red LED,
ی Device triggering by means of the L or

N wire,

ی Applicable together with the single

pole push buttons, illuminated,
ی Easy applicable together with any exi-

sting electrical system,
ی Counter-interlock function,
ی Relay voltage output, maximum load

5 A.

TECHNICAL DATA

Power supply cables: L(black), N(blue)

Input rated voltage: 230 V~

Input voltage tolerance: from -15 to +10 %

Nominal frequency: 50 / 60 Hz

Rated power consumption: 10,5 mA

Time adjustment range: from 10 s to 14 min

Time accuracy adjustment: ±10 %

Time repeatability adjustment: ±5 %

Time adjustment: continuous (rotational potentiometer)

Load supply indicator: red LED

Number of switch cables: 4

Section of connecting cables: 1 mm

Connecting cable length: 10 cm

Ambient temperature range: from -20 to +45

Operating position: free

Protection degree: IP20

Protective class: II

Overvoltage category: II

Pollution degree: 2

Reference standards: PN-EN 60669-1; PN-EN 60669-2-1

ASP-02

Release cable: IN (red)

Output cable: (P) brown

Control: relay 5 A / 250 V AC1 1250VA

2

Mounting: for 60 mm junction box

Dimensions: 50 x 50 x 15 mm

Weight: 28 g

PN-EN 61000-4-2,3,4,5,6,11

o

C

The device should be
connected to a sin­glephase system ac­cordingly to current

CAUTION

standards. The device
connection swill be de-

scribed in this manual.
Only qualied electricians are allowed
to connect, assembly and adjust the ti­me r. It is ne ce ss ar y to rea d t his manu al
before the timer mounting. Do not di­sassembly the timer casing or you will
lose any warranty rights and expose
yourself to the electric shock hazard.
Before mounting operation make sure
of disconnecting the connection wires
from the electric network. Use a cross­head screwdriver of 3.5 mm diameter
to mount the device. The timer should
be carried, stored and used in an ap ­propriate way. Do not mount the timer
in c ase of any dev ice par ts lack, dama­ge or deformation. In case of malfunc­tion please notify the manufacturer.

APPERANCE

Load supply indicator

Time adjustment

Release cable (IN)

Power supply cable (N)

Output cable (P)

Power supply cable (L)

d

e

r

e

u

l

b

n

w

o

r

b

k

c

a

l

b

VER. 002_12.12.2008

1. Disconnect the electric network by

means of an appropriate cut-off, cur­rent limiting circuit-breaker or separa­tor.

2. Check if there is no any voltage be-

tween power leads by means of an
appropriate gauge.

3. Place the ASP-02 timer in a junction

box and connect leads accordingly to
electrical diagram.

4. Connect power supply circuit.

5. Adjust the light ON-time required by

means of the potentiometer.

FUNCTIONING

CONNECTINGMOUNTING

L/N

d

e

r

e

u

l

b

n

w

o

r

b

k

c

a

l

b

The timer is ready to work just right
after its appropriate connecting. The light
will be ON for the preset ON-time after
the timer is triggered by means of a single
pole push button. When the preset time
is over, the light will be OFF automatical­ly until the timer is triggered once again.
The staircase timer may be connected
either to three-conductor or four-con­ductor wiring. Check carefully if trigger
and load circuits have been connected
correctly. The timer may be damaged if
connected inappropriately. In case of the
counter-interlock circuit lack the light is
continuously ON when the trigger push
button is blocked.

INNER DIAGRAM

NL

IN

t

EXAMPLE OF INSTALLATION

r

e

d

b

l

u

e

b

r

o

w

n

b

l

a

c

k

DIMENSIONS

TIME COURSE PRODUCT FAMILY

The ASP-02 is a member of the ASx
staircase timer family.

Version 24 V AC/DC

for ASM-02 available

Device version:

01 – three - or four-conductor

wiring

02 – anti-lock system

RELAY CAPACITY

375 W 180 W

90 W 150 W

10 – dimmer function

Type of casing:

M – monomodular
N – surface mounting
H – hermetical
P – for junction box mounting

Device symbol

VER. 002_12.12.2008