Owner’s Manual
Active 120
2 in 1 Cycle Cross Trainer
Item #52060
ACTI VE
12 0
17JANUARY2013
www.yorkfitness.com
www.yorkfitness.com
2
Table of contents
Congratulations on
purchasing your exercise
equipment from
You have chosen a high quality, safe and
innovative piece of equipment as your
training partner and we are certain it will
keep you motivated on the way to achieving
your personal tness goals.
Please take the time to read this owner’s
manual as it will help you to get the most out
of your new exercise equipment.
For more information visit www.yorktness.com
CONTENTS
Safety information 03
Customer support 04
Assembly instructions 05
Operational instructions 11
Troubleshooting 16
Fitness guide 18
Exploded drawing 20
Part list 22
Protect the environment by not disposing
of this product or batteries with household
waste. Check your local authority for
recycling advice and facilities.
www.yorkfitness.comwww.yorkfitness.com
3
Safety information
Please read this instruction manual before you
begin assembly. Great care has been taken
to design these instructions and following
them will help you with quicker assembly and
minimize the risk of injury.
It is important that you keep these
instructions for future reference.
This list is not exhaustive - You are
responsible for your own safety!
• Always assemble and operate the equipment on a
level surface.
• Ensure the equipment is stable before use.
• Always ensure that the equipment has adequate
space on each side.
• Ensure that the seat height is adjusted correctly. You
should be stable and balanced while on the saddle.
• Adjust the seat height to ensure that you
have a good downward pedal stroke without
overstretching, don’t compromise your balance.
• Try to ensure that your back is straight while
exercising, especially for long periods.
• The safety level of this equipment can only be
maintained if it is regularly examined for wear and tear.
• Replace defective components immediately and
keep the equipment out of use until it is repaired.
• Use only the adjustment setting as described in the
instructions. Always use the correct adjustment pin
/ xing.
• Always check that any pins / xings are tight and
secure before use and after adjustment.
• Never leave any adjustment devices projecting from
the equipment.
• Always consult your doctor before undertaking any
exercise program.
• Always wear suitable clothing and footwear. (e.g.
tracksuit / shorts / training shoes)
• Remove all personal jewelry before exercising.
• Ensure you warm-up well before using the equipment
as this will help to prevent muscle strain.
• After eating, allow 1-2 hours before exercising as
this will help to prevent muscle strain.
• Never overload the equipment. (See maximum user
weight)
• Never use the equipment in any other manner other
than the ways explained in these instructions and
any wall-chart supplied.
• Injuries to health may result from incorrect or
excessive training.
• Parents and others in charge of children should be
aware of their responsibility, because the natural
play instinct and the fondness of experimenting
of children can lead to situations and behavior for
which the training equipment is not intended.
• If children are allowed to use the equipment, their
mental and physical development and above all
their temperament should be taken into account.
They should be controlled and instructed in the
correct use of the equipment.
• The equipment is under no circumstances suitable
as a children’s toy.
• Children should not be allowed on or around the
equipment, especially when it is not in use.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
• This product is not suitable for therapeutic purposes.
• This product has an integrated speed independent
braking system without a constant power mode that
is governed by magnetic resistance.
• This product has been tested for use in a home
environment and is warranted for In Home,
personal, family or household use.
• Due to our continuous policy of product
development, York Fitness reserves the right to
change specications without notice.
CAUTION! The instructions must be
followed carefully in the assembly, use
and maintenance of your equipment. The
warranty does not cover damage due to
negligence of the assembly, adjustment and
maintenance instructions described herein.
Maximum user weight: 110kg
Safety Standards
This equipment meets the requirements of the
EU’s EMC and Low Voltage directives (where
applicable), EN957- 1, 9 Class HC. Therefore
the equipment carries the following marks:
www.yorkfitness.com
4
Customer support
Should you require any assistance regarding this product please gather the following
information and then contact us using the details below:
• Serial No. - This can be found on the sticker below, located as indicated.
• Original purchase date
• Place of purchase
• Information about the place and conditions of use
• Precise description of the issue / defect
Use only on a level surface
Not suitable for therapeutic purpose
Manufacturer: YORK BARBELL
Contact: York Way, Daventry, England, NN11 4YB
Product Name: York Active 120 Cycle Cross Trainer
Max User Weight: 110KG
Safety Standards: EN957-1,9 Class HC
Electrical info: Adaptor 9V, 500mA
SERIAL NO:
52060-
Product’s Name
Serial Number
This product label is an example only, it is not the
real product name and serial number of the item
you have bought.
Underside of the
main body.
ACTIVE
120
IMPORTANT!! - Please retain your sales receipt, York Fitness Customer Care may request
proof of purchase to validate eligibility for warranty service. Warranty cover starts from the date
shown on the proof of purchase.
ENGLAND
The best way to contact us is via the website:
www.yorktness.com
York Barbell UK Ltd.
York Way, Daventry,
England, NN11 4YB
Tel: 0844 225 3112
AUSTRALIA
The best way to contact us is via the website:
www.yorktness.com.au
York Fitness Australia
1/2 Swaffham Rd, Minto,
PO Box 5130, NSW 2566
Tel: 1800 730 149
www.yorkfitness.comwww.yorkfitness.com
5
Assembly instructions
Care & Maintenance
• This equipment should not be placed outdoors, in a garage or an outbuilding. Keep the equipment in a dry
place with as little temperature variation as possible.
• We recommend placing a mat beneath the equipment to protect both the equipment and your ooring.
• Always place the equipment in a dry environment.
• Use a warm, damp cloth to keep the product clean.
• No wet cleaning of electrical components. Unplug before any care and maintenance.
• The safety level of the equipment can be maintained only if it is regularly examined for damage and wear. This
includes any ropes, pulleys, nuts, bolts, moving parts, bushes, chains, wheels, bearings & connection points etc.
• Ensure that you inspect the product regularly - at least once a week is recommended.
• Ensure that all xings are tight before use.
• Always replace damaged / worn components with original parts from the manufacturer.
Prepare your work area - It is important you assemble the product in a clean and uncluttered space.
Work with a friend - We recommend you have someone assist you with the assembly as some
of the components are quite heavy.
Open the carton - Check any warnings on the carton and make sure you have it the right way up.
Unpack the carton - Remove all the parts and lay them out on the oor.
Blister Pack
STEP 1
STEP 4
STEP 5
STEP 6
STEP 7
N-6 x 2
(M5*0.8*15L)
N-3 x 10
(D15.4*D8.2*2T)
N-5 x 10
(M8*1.25*20L)
N-4 x 10
(D22*D8.5*1.5T)
O x 1
(114*76*43)
N-3 x 4
(D15.4*D8.2*2T)
N-2 x 4
(M8*1.25*15L)
N-4 x 4
(D22*D8.5*1.5T)
N-12 x 2
(M8*1.25*25L)
N-11 x 2
(D29*21*M8)
N-3 x 2
(D15.4*D8.2*2T)
N-9 x 2
(D25*D8.5*2T)
N-10 x 2
(D26*D19.5)
N-7 x 8
(M6*15L)
N-8 x 8
(D14*D6.5*0.8T)
N-1 x 4
(M8*1.25*75L)
www.yorkfitness.com
6
Make sure you have the following parts:
Z x1 C x1
S x1
H x1
B x1
O x1
E x1F x1
G x1
R x1 A x1
U x1 V x1 W x1 N x1
Assembly instructions
www.yorkfitness.comwww.yorkfitness.com
7
N-1 x 4
N-4 x 4
N-3 x 4
N-2 x 4
G
N-1
Z
F
N-1
N-4
N-3
N-2
1
UP
DOWN
FORWARD
BACKWARD
U-3
U
V
U-4
2
www.yorkfitness.com
8
C
Z
C-3
D-7
3
N-7 x 8
N-8 x 8
H
P
N-7 N-8
4
Assembly instructions
www.yorkfitness.comwww.yorkfitness.com
9
N-9 x 2
N-11 x 2
N-10 x 2
N-3 x 2
N-12 x 2
N-10
N-10
C
Q
S
N-11
N-12
N-3
N-9
5
N-3 x 10
N-4 x 10
N-5 x 10
6
Q
O
N-5
E
B
N-4
N-3
C
N-5
N-3
A
N-4
www.yorkfitness.com
10
A-2 x 4
N-6 x 2
7
N-6
W
C
A-1
A-2
B-4
C-3
Final Check
Your equipment is now assembled.
Please make the following nal checks:
• Make sure all screws / bolts are tightened.
• Make sure the equipment is on a at, level surface.
ACTIVE
12 0
Assembly instructions
www.yorkfitness.comwww.yorkfitness.com
11
Hand Pulse Sensors
This exercise equipment is tted with 2 hand
pulse sensors. To obtain a pulse reading you
must have both your left and right hands on
the sensors at the same time. Do not grip the
hand sensors too tight and allow the computer
a few seconds to display the reading.
Hand Pulse Sensor
Levelling
To help you level the equipment on uneven
surface, 2 height adjusters are included on the
rear stabilizers. Simply twist these around to
adjust the height of the equipment.
ACT IV E
1 2 0
Adjust The Seat
Simply adjust the knob under the seat to
move forward or backward.
Adjust The Seat Height
Note: Do not pull the seat out too far - the maximum is indicated
with a piece of tape on the seat post.
1. Unscrew the hand wheel.
2. Adjust the seat up or down to your required height - to line it
up correctly, make sure the number and line is visible at the
top of the seat post mounting tube.
3. Re-screw the hand wheel - make sure it is screwed tightly.
4. The basic rule for getting the seat height right is that as the
pedal reaches its lowest point, the leg is almost straight.
ACT IVE
1 2 0
Operational instructions
www.yorkfitness.com
12
Console
This exercise equipment features a speed
independent braking (resistance) system. The
resistance is controlled by a magnet, which is
moved closer or further away from the ywheel
- the closer the magnet is to the ywheel the
higher the resistance.
MODE
BODY FAT RECOVERY DOWN UP
P1 P2
P3
P4
P5 P6
P12P11
P10P9P8
P7
RESET START/STOP
ITEM DESCRIPTION
TIME • Workout time displayed during exercise.
• Range 0:00 ~ 99:59
SPEED • Workout speed displayed during exercise.
• Range 0.0 ~ 99.9
DISTANCE • Workout distance displayed during exercise.
• Range 0.0 ~ 99.9
CALORIES • Burned calories during workout display.
• Range 0 ~ 999
PULSE • Pulse bpm displayed during exercise.
• Pulse alarm when over preset target pulse.
RPM • Rotation per minute
• Range 0 ~ 999
WATT • Workout power consumption
• In Watt Program mode, computer will remain preset watt value
(setting range 0~350)
MANUAL • Manual mode workout.
PROGRAM • 12 PROGRAM selection.
USER • User creates resistance level prole.
H.R.C. • Target HR training mode.
Operational instructions
www.yorkfitness.comwww.yorkfitness.com
13
Key Function:
FUNCTION DESCRIPTION
Up • Increase resistance level
• Setting selection.
Down • Decrease resistance level
• Setting selection.
Mode • Conrm setting or selection.
Reset • Hold on pressing for 2 seconds, computer will reboot and start
from user setting.
• Reverse to main menu during presetting workout value or stop
mode.
Start/ Stop • Start or Stop workout.
Recovery • Test heart rate recovery status.
Body Fat • Test body fat% and BMI.
Power On
Plug in power supply, computer will power on and display all segments on LCD for 2 seconds.
Enter into user data setting mode (Age, Sex, Height, Weight)
After 4 minutes without pedaling or pulse input, console will enter into power saving mode.
Press any key may wake the console up.
Manual Mode
Press START in main menu may start workout in manual mode.
1. Press UP or DOWN to select workout program, choose Manual and press Mode to enter.
2. Press UP or DOWN to preset TIME, DISTANCE, CALORIES, PULSE and press MODE
to confirm.
3. Press START/STOP keys to start workout. Press UP or DOWN to adjust load level.
4. Press START/STOP keys to pause workout. Press RESET to reverse to main menu.
Program Mode
1. Press UP or DOWN to select workout program, choose the Program and press Mode to
enter. (Total Program = 12)
2. Press UP or DOWN to preset TIME.
3. Press START/STOP key to start workout. Press UP or DOWN to adjust load level.
4. Press START/STOP key to pause workout. Press RESET to reverse to main menu.
www.yorkfitness.com
14
User Program Mode
1. Press UP or DOWN to select workout program, choose User and press Mode to enter.
2. Press UP or DOWN to set load level of each column, and press MODE to next one.
(Total column = 20)
3. Hold on pressing MODE to nish or quit setting.
4. Press UP or DOWN to preset workout TIME.
5. Press START/STOP key to start workout. Press UP or DOWN to adjust load level.
6. Press START/STOP key to pause workout. Press RESET to reverse to main menu.
H.R.C. mode
1. Press UP or DOWN to select workout program, choose H.R.C. and press Mode to enter.
2. Press UP or Down to select 55%.75%.90% or TAG (TARGET H.R.) (default: 100).
3. Press UP or DOWN to preset workout TIME.
4. Press START/STOP key to start or stop workout. Press RESET to reverse to main menu.
WATT Mode
1. Press UP or DOWN to select workout program, choose WATT and press Mode to enter.
2. Press UP or DOWN to preset WATT target. (default: 120)
3. Press UP or DOWN to preset TIME.
4. Press START/STOP key to start workout. Press UP or DOWN to adjust Watt level.
5. Press START/STOP key to pause workout. Press RESET to reverse to main menu.
Recovery
1. User must be holding the handgrip. When the pulse value is displayed on the computer,
press on the RECOVERY key.
2. TIME shows “0:60” (seconds) and count down.
Computer will show F1 to F6 after count down to 0 to test heart rate recovery status.
1.0 OUTSTANDING
1.0 « F « 1.9 EXCELLENT
2.0 « F « 2.9 GOOD
3.0 « F « 3.9 FAIR
4.0 « F « 5.9 BELOW AVERAGE
6.0 POOR
Operational instructions
www.yorkfitness.comwww.yorkfitness.com
15
Body Fat Mode
1. When workout stop, press BODY FAT key.
2. Hold on handgrip, after 8 seconds, computer will show BMI, FAT% and fat symbol.
3. Press BODY FAT key again reverse to main menu.
B.M.I. (Body mass index) integrated
B.M.I SCALE LOW LOW/MED MEDIUM MED/HIGH
RANGE « 20 20 - 24 24.1 - 26.5 » 26.5
Body Fat
Sex \ Symbol LOW ( - ) LOW/MED ( + ) MEDIUM ( ▲ ) MED/HIGH ( ◆ )
MALE <13% 13%-25.9% 26%-30% >30%
FEMALE <23% 23%-35.9% 36%-40% >40%
Troubleshooting:
CODE DESCRIPTION
E-1 Hands are not hold on tightly on grips during BODY FAT test.
E-4 Check the user’s age, height, weight gure setting when the test
result is out of the range of FAT% 5~50 and BMI 5~50%
E-2 Check if cables are well connected or damaged.
www.yorkfitness.com
16
Troubleshooting
If you have a problem with your exercise equipment, before you do anything else please check
that all the cables have been connected correctly. Loose cables are very common and many
problems can be solved by making sure the cables are properly connected.
The following table details the most common problems and how to x them. If you still have a problem
after going through the troubleshooting guide please call your local YORK distributor for advice.
PROBLEM CAUSE CORRECTION
NO DISPLAY No power Plug in power
NO SPEED
DISPLAY
Wires are damaged or not
connected properly
Verify all wires are connected
properly
Speed sensor is too far from
magnet
Contact your local YORK distributor
PARTIAL DISPLAY
The PA board is not connected
properly
Verify all wires are connected
properly
Disconnect and re-connect all
cables
Contact your local YORK distributor
NO PULSE
SIGNAL
Wires are damaged or not
connected properly
Verify all wires are connected
properly
Too much hand movement Dry palms
Palms too wet Grip using moderate pressure
Hand Pulse Sensor is being gripped
too tightly
Remove all rings
User is wearing rings Contact your local YORK distributor
FOR YOUR OWN SAFETY, DO NOT OPEN PROTECTIVE CASING. IF ERROR PERSIST,
PLEASE CONTACT YOUR LOCAL YORK DISTRIBUTOR FOR ADVICE. KEEP THE EQUIPMENT
OUT OF USE UNTIL IT IS REPAIRED.
If you are having problems with your heart rate reading, please note that some bres
used in clothes eg) polyester, create static electricity that may prevent a reliable heart rate
reading. Mobile phones, TV’s, microwaves and other electrical appliances that generate an
electromagnetic eld may also interfere with heart rate measurement.
www.yorkfitness.comwww.yorkfitness.com
17
Notes
www.yorkfitness.com
18
Fitness guide
Correct Cycling Form
• Sit on the cycle, with your feet on the pedals and inside the pedal straps.
• Ensure that the seat height is adjusted correctly - you should be stable and balanced whilst on the saddle. The
basic rule for getting the seat height right is that as the pedal reaches its lowest point, the leg is almost straight.
• Try to ensure that your back is straight whilst exercising, especially for long periods.
Correct Cross-training Form
To start using the cross trainer, simply stand on the foot pedals with the front of your shoes close to the front edge
of the pedal cap. Place your hands at a comfortable position on the handlebars. Simply move your highest foot
forward and follow the natural path of the machine.
Start on a load level that is comfortable to familiarize yourself with the machine. Once you are comfortable, start
adjusting the load level to achieve the workout desired.
Forward and Reverse: The cross trainer can be used in the forward and reverse direction to vary the muscles that
you workout. This will also vary your workout helping you to stay motivated. To change directions, simply slow the
pedals down until they stop and switch directions.
Load Level Adjustment: The load level of cross trainer can be changed at any time during your workout.
Adjusting your load level will allow you to increase or decrease your intensity level.
Suggested Stretches
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never
bounce.
1. Hamstring Stretch
Sit with one leg
extended. Bring the
sole of the opposite
foot toward you and
rest it against the inner
thigh of your extended
leg. Reach toward your
toes as far as possible.
Hold for 15 counts, then
relax. Repeat 3 times
for each leg. Stretches:
Hamstrings, lower back
and groin.
2. Calf/Achilles Stretch
With one leg in front of
the other, reach forward
and place your hands
against a wall. Keep your
back leg straight and
your back foot at on the
oor. Bend your front leg,
lean forward and move
your hips toward the
wall. Hold for 15 counts,
then relax. Repeat 3
times for each leg. To
cause further stretching
of the achilles tendons,
bend your back leg as
well. Stretches: Calves,
achilles tendons and
ankles.
3. Quadriceps Stretch
With one hand against
a wall for balance,
reach back and grasp
one foot with your
other hand. Bring your
heel as close to your
buttocks as possible.
Hold for 15 counts, then
relax. Repeat 3 times
for each leg. Stretches:
Quadriceps and hip
muscles.
4. Inner Thigh Stretch
Sit with the soles of your
feet together and your
knees outward. Pull your
feet toward your groin
area as far as possible.
Hold for 15 counts, then
relax. Repeat 3 times.
Stretches: Quadriceps
and hip muscles.
www.yorkfitness.comwww.yorkfitness.com
19
How Long Should I Exercise For?
That really depends on your current level of tness. If you’re just starting out on a new exercise program, you should
start gradually and build up - do not try to do too much too quickly. 30 minutes, 3 times a week should be enough.
Don’t push yourself too hard - you should never feel exhausted during or following exercise.
Heart Rate Training
To get the most out of your new piece of tness equipment and see the best results from your training you should
exercise at the right level of effort, and that means listening to your heart! Working out to a target heart rate means
you can direct your workout to achieve different goals:
Good health - For those wishing to improve quality of life and general well being. Your sessions will need to be
done at an intensity of between 50 - 60% of your estimated maximum heart rate, should last about 30 minutes and
can be done on most days of the week.
Weight loss - To see a signicant reduction in body fat, your sessions must be a little more intense - between 60
and 70% of your estimated maximum heart rate. These sessions can also be performed on most days of the week
for up to 30 minutes.
Improving tness levels - These sessions should be performed at 70 - 80% of your estimated maximum heart rate
and can also involve bouts of interval training that would have your heart rate peaking for short times near your
maximum heart rate level. These are intense sessions and will require at least a 48 hour rest between sessions.
Calculating Your Target Heart Rate
First, you need to nd your estimated maximum heart rate using the formula “220 minus your age in years”. So, if
you are 35 years old your estimated maximum heart rate is:
220 - 35 = 185 beats per minute (bpm)
Next, to calculate your target heart rate, simply multiply your estimated maximum heart rate (185bpm) by the
applicable percentage. So, if your goal is better health:
185 x 60% = 111bpm
NOTE: The important issue to remember with all estimated calculations is that they are just estimates - if you don’t
feel comfortable exercising at your target then reduce it to a level you are comfortable with.
Heart rate training requires you to monitor your heart rate throughout the workout. For this we recommend using
a chest strap (if your machine has a wireless receiver) or a heart rate monitor. For more information please get in
touch using the Contact Us details.
Always consult your doctor before undertaking a new exercise regime. If you experience nausea, dizziness or other
abnormal symptoms during exercise, stop at once and consult your doctor.
www.yorkfitness.com
20
N-12
N-11
N-3
N-9
S
U
U-3
U-4
V
H
Z
N-4
N-3
N-2
G
P
N-8
N-7
N-10
N-3
N-5
Q
N-4
N-6
W
C
A-2
A-1
B
O
N-4
N-3
N-5
N-5
N-3
E
N-4
F
N-1
Exploded drawing
www.yorkfitness.comwww.yorkfitness.com
21
E C D P
B T K
L
J
F G
A M
O W R
Q I
S H U V
E-2
E-3
E-4
E-1
B-5
B-3
B-6
B-2
B-1
F-2
G-3
G-1
G-2
V-2V-1
U-1
U-2
U-3
U-4
U-5
U-6
F-1
F-3
A-1
A-2
B-4
C-3
D-2
D-12
D-11
D-4 D-7
D-5
D-8
D-6
D-10
P-11
P-10
P-9
P-8
P-5
P-4
P-3
P-6
P-2
P-1
J-1
J-2
I-3
I-2
I-4I-5
J-5
J-4J-3
L-2
L-4
Q-2
Q-1
Q-3
Q-5
Q-4
M-9
M-6M-1M-2M-3M-4M-5
M-7
M-8
L-5
L-6
L-8
L-7
L-9
K-8
K-9
T-5T- 4T-3T-2T-1
T-7
T-6
K-1
K-2
K-3
K-4
K-5
K-6
K-7
L-1
L-3
L-11
L-10
K-10
K-11
P-12
P-7
D-3
D-1
C-2
C-1
www.yorkfitness.com
22
YORK REF. REF. DESCRIPTION QTY.
52060-001 A COMPUTER SET 1
52060-002 A-1 COMPUTER (SM-2789-67) 1
52060-003 A-2 BOLT (M5*0.8*10L) 4
52060-004 B FIXING BAR SET 1
52060-005 B-1 FIXING HANDLEBAR 1
52060-006 B-2 FOAM (D23X7TX460L) 2
52060-007 B-3 HAFF BALL END CAP 2
52060-008 B-4 HAND PULSE CABLE (600L) 2
52060-009 B-5 HAND PULSE SENSOR (PE18) 2
52060-010 B-6 SCREW (ST4*15L) 2
52060-011 C HANDLEBAR POST SET 1
52060-012 C-1 HANDLEBAR POST 1
52060-013 C-2 BUSHING - D19.15X(D25.6X32)XL(17+3) 2
52060-014 C-3 UPPER COMPUTER CABLE (900L) 1
52060-015 D MAIN FRAME SET 1
52060-016 D-1 MAIN FRAME 1
52060-017 D-2 INNER TUBE 1
52060-018 D-3 MOTOR 1
52060-019 D-4 SCREW (ST4.2*1.4*15L) 4
52060-020 D-5 SENSOR CABLE (100L) 1
52060-021 D-6 BOLT (M5X0.8X12L) 1
52060-022 D-7 LOWER COMPUTER CABLE (1200L) 1
52060-023 D-8 TENSION CABLE (D1.5*200 L) 1
52060-024 D-9 BEARING (#6003ZZ) 2
52060-025 D-10 ELECTRIC CABLE (150L) 1
52060-026 D-11 KNOB 1
52060-027 D-12 INNER TUBE 1
52060-028 E MOVEABLE HANDLEBAR 1
52060-029 E-1 RIGHT MOVEABLE BAR 1
52060-030 E-2 LEFT MOVEABLE BAR 1
52060-031 E-3 MUSHROOM CAP 2
52060-032 E-4 FOAM (D30*7T*390L) 2
52060-033 F FRONT STABILIZER SET 1
52060-034 F-1 FRONT STABILIZER 1
52060-035 F-2 RIGHT MOVEABLE CAP 1
52060-036 F-3 LEFT MOVEABLE CAP 1
52060-037 G REAR STABILIZER SET 1
52060-038 G-1 REAR STABILIZER 1
52060-039 G-2 ADJUSTABLE CAP 2
52060-040 G-3 SCREW (ST4X1.41X10L) 2
52060-041 H PEDAL 2
52060-042 I CRANK SET 1
52060-043 I-1 CRANK 2
52060-044 I-2 ANTI-LOOSEN NUT (M10*1.25*7T) 2
52060-045 I-3 SIDE COVER 2
52060-046 I-4 ROUND COVER 2
52060-047 I-5 SCREW (ST4X1.41X15L) 8
52060-048 J CHAIN COVER SET 1
52060-049 J-1 ROUND RING FOR CHAIN COVER 1
52060-050 J-2 SCREW (ST4.2X1.4X20L) 4
52060-051 J-3 LEFT CHAIN COVER 1
52060-052 J-4 RIGHT CHAIN COVER 1
52060-053 J-5 SCREW (ST4X1.41X20L) 4
52060-054 K FIXING PLATE FOR MAGNET SET 1
52060-055 K-1 FIXING PLATE FOR MAGNET 1
52060-056 K-2 SPRING (D1.0*42L) 1
52060-057 K-3 NYLON NUT (M6*1*6T) 1
52060-058 K-4 FLAT WASHER (D13*D6.5*1.0T) 1
52060-059 K-5 NYLON NUT (D6*D19*1.5T) 1
52060-060 K-6 NUT (M6*1*6T) 1
52060-061 K-7 HEX BOLT (M6*65L) 1
52060-062 K-8 NYLON NUT (M8*1.25*8T) 1
52060-063 K-9 BOLT (M8*52L) 1
52060-064 K-10 MAGNET 8
52060-065 K-11 PLATE FOR MAGNET 7
YORK REF. REF. DESCRIPTION QTY.
52060-066 L FIXING PLATE FOR IDLE WHEEL SET 1
52060-067 L-1 FIXING PLATE FOR IDLE WHEEL 1
52060-068 L-2 SPRING (D3*D17*59L) 1
52060-069 L-3 FLAT WASHER (D50*D10*3.0T) 1
52060-070 L-4 PLASTIC WASHER (D10*D24*0.4T) 1
52060-071 L-5 HEX BOLT (M8*1.25*30L) 1
52060-072 L-6 FLAT WASHER (D30*D8.2*3.0T) 1
52060-073 L-7 FIXING RING (D13*D10*1.9T) 1
52060-074 L-8 IDLE WHEEL 1
52060-075 L-9 C-CLIP - S-10(1T) 1
52060-076 L-10 NUT (M8*1.25*6T) 1
52060-077 L-11 NYLON NUT (M8*1.25*8T) 1
52060-078 M BELT WHEEL SET 1
52060-079 M-1 WAVED WAHSER (D17*D22*0.3T) 2
52060-080 M-2 FLAT WASHER (D23*D17.2*1.5T) 1
52060-081 M-3 C-CLIP - S-17(1T) 2
52060-082 M-4 BELT - 420(1067)L PJ5 1
52060-083 M-5 BELT WHEEL 1
52060-084 M-6 CRANK AXLE 1
52060-085 M-7 ROUND MAGNET 1
52060-086 M-8 HEX BOLT (M6*1.0*15L) 4
52060-087 M-9 NYLON NUT (M6X1.0X6T) 4
52060-088 N-1 SQUARE NECK BOLT (M8X1.25X75L) 4
52060-089 N-2 DOMED NUT (M8X1.25X15L) 4
52060-090 N-3 SPRING WASHER (D15.4XD8.2X2T) 16
52060-091 N-4 CURVED WASHER (D22XD8.5X1.5T) 14
52060-092 N-5 ALLEN BOLT (M8X1.25X20L) 10
52060-093 N-6 BOLT (M5*0.8*20L) 2
52060-094 N-7 SCREW (M6X15L) 8
52060-095 N-8 FLAT WASHER (D14XD6.5X0.8T) 8
52060-096 N-9 FLAT WASHER (D25XD8.5X2T) 2
52060-097 N-10 WAVED WAHSER (D26*D19.5*0.3T) 2
52060-098 N-11 SCREW COVER - D29*21(M8) 2
52060-099 N-12 HEX BOLT (M8X1.25X25) 2
52060-100 O PROTECTIVE COVER 1
52060-101 P PEDAL SET 1
52060-102 P-1 PEDAL SET 2
52060-103 P-2 END CAP 4
52060-104 P-3 NYLON NUT (M10*1.5*10T) 2
52060-105 P-4 FLAT WASHER (D20*D11*2.0T) 2
52060-106 P-5 BUSHING - D19.15X(D25.6X32)XL(17+3) 4
52060-107 P-6 BUSHING (D29*D11.9*9T) 4
52060-108 P-7 C-CLIP (D21.5XD17.5X1.2T) 4
52060-109 P-8 JONIT 2
52060-110 P-9 FLAT WASHER (D24*D13.5*2.5T) 2
52060-111 P-10 LADDER BOLT (M10*1.5*58L) 2
52060-112 P-11 SCREW COVER - D30*17(M12) 2
52060-113 P-12 SCREW COVER - D28*17(M10) 2
52060-114 Q MOVEABLE SUPPORTING TUBE SET 1
52060-115 Q-1 MOVEABLE SUPPORTING TUBE 2
52060-116 Q-2 BUSHING - D19.15X(D25.6X32)XL(17+3) 8
52060-117 Q-3 FRONT PEDAL AXLE 2
52060-118 Q-4 C-CLIP (D21.5XD17.5X1.2T) 4
52060-119 Q-5 WAVED WASHER (D26*D19.5*0.3T) 2
52060-120 R ADAPTOR (OUTPUT 9VA) 1
52060-121 S AXLE - D19X374.5(M8X1.25) 1
52060-122 T FLYWHEEL SET 1
52060-123 T- 1 FLY WHEEL 1
52060-124 T- 2 FLYWHEEL AXLE - D10X120L(3/8"-26UNF) 1
52060-125 T- 3 FIXING RING (D13*D10*1.9T) 1
52060-126 T- 4 NUT - D9.5X3T(3/8"-26UNFX3T) 1
52060-127 T- 5 ANTI-LOOSEN NUT (3/8"-26UNF*6.5T) 2
52060-128 T- 6 NUT - D9.5X5T(3/8"-26UNFX5T) 2
52060-129 T- 7 BEARING (#6000ZZ) 2
52060-130 U SEAT ADJUSTMENT TUBE SET 1
Part list
www.yorkfitness.comwww.yorkfitness.com
23
YORK REF. REF. DESCRIPTION QTY.
52060-131 U-1 SEAT 1
52060-132 U-2 SEAT ADJUSTMENT TUBE 1
52060-133 U-3 FLAT WASHER (D25XD8.5X2T) 1
52060-134 U-4 CLUB KNOB 1
52060-135 U-5 FLAT WASHER (D18*D8.5*1.2T) 3
52060-136 U-6 NYLON NUT (M8*1.25*8T) 3
52060-137 V SEAT POST SET 1
52060-138 V-1 OVAL CAP (25*50*28L) 2
52060-139 V-2 SEAT POST 1
52060-140 W PROTECTIVE COVER 1
www.yorkfitness.com
Loading...