York E4FD018, E4FD024, E4FD036, E4FD030, E4FD042 Technical Manual

...

Download

Page 1

TECHNICAL GUIDE

STELLAR 2000

10 SEER

SPLIT-SYSTEM HEAT PUMPS

MODELS: E*FD018 Thru E*FD060 (1.5 THRU 5 NOMINAL TONS, 1 PH )

E*FD036 Thru E*FD060 (3 THRU 5 NOMINAL TONS, 3 PH )

This product was manufactured in a plant whose quality system is certified/registered as being in conformity with ISO 9001.

Due to continuous product improvement, specifications are subject to change without notice.

Visit us on the web at www.york.com for the most up-to-date technical information.

Additional rating information can be found at www.ari.org

I N

with ARI.

M P

T C

U N

Certification applies only

when the complete

system is listed

LISTED

036-21030-003 Rev. B (0203)

DESCRIPTION

The EFD Series heat pump is the outdoor part of a versatile system designed to economically heat and cool a home or small business. The compact design of these outdoor units make them ideal for ground or roof installation. They are available with sweat connect field piping connections. These units have service valves and contain enough refrigerant charge for the outdoor unit, a matching indoor coil and 15 feet of interconnecting piping.

EFD heat pumps may be custom-matched with one of YORK's indoor line of evaporator blower sections, each designed to serve a specific function. Electric heaters are available for both single and three phase applications, in a variety of sizes.

For Add-On applications, the indoor coil may be applied in the supply duct of a conventional gas, oil or electric furnace. The heat pump will be the primary source of heat for the building with the furnace operating only when the heating requirement exceeds the capacity of the heat pump.

WARRANTY

5-year lim

5-year limited co

ited parts warranty.

mpressor warranty.

FEATURES

• QUALITY CONDENSER COILS - The coil is constructed of enhanced copper tube and aluminum fins.

• COIL PROTECTION - Coils are protected from damage by a polymer mesh applied between the coil face, and a PVC coated steel coil guard.

• DEFROST CONTROL - Time / Temperature defrost control provides field selectable time periods between defrost cycles (30, 60 and 90 minutes). LED lockout indicator, anti-short cycle timer protection are also provided. A built-in soft lockout helps to avoid nuisance trips on high pressure.

• PROTECTED COMPRESSOR - The compressor is internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protect the compressor if undesirable operating conditions occur. All units have standard crankcase heat for added protection (except 048 and 060, since they are scroll compressors).

• DURABLE FINISH - Cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and glossy earth tone finish insure less fading when exposed to sunlight.

• LOWER INSTALLED COST - Installation time and costs are reduced by the fully exposed refrigerant connections and the single panel covering of the electrical controls. The small base dimension means smaller mounting pads or less materials required for mounting, thus lowering installation costs.

• TOP DISCHARGE - The air from the top mounted fan is blown up away from the structure and any landscaping. This allows space saving arrangements of multi-unit installations.

• LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise up and away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. A compressor blanket accessory is available for those applications requiring further sound reduction.

• LOW MAINTENANCE - Long life permanently lubricated motor- bearings need no annual servicing.

• RE-USABLE SERVICE VALVES - Provided on all sweat fit- tings on both the liquid and vapor connections for ease of evacuating.

• U.L. and C.U.L. listed - approved for outdoor application.

Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

Page 2

036-21030-003 Rev. B (0203)

PHYSICAL AND ELECTRICAL DATA - 1 Phase

MODEL

E4FD018 E4FD024 E4FD030 E4FD036 E4FD042 E4FD048 E4FD060

Unit Supply Voltage 208/230-1-60

Normal Voltage Range

187 to 252

Minimum Circuit Ampacity 11.3 15.4 19.4 23.2 27.2 33.1 39.2

Max. Overcurrent Device Amps

Compressor Type

Compressor Amps

Rated Load 6.7 11.6 14.8 17.3 20.5 25.2 29.9

Locked Rotor 48 60 73 86 120 131 165

20 25 30 35 40 50 60

Recip Recip Recip Recip Recip

Scroll

Crankcase Heater Yes Yes Yes Yes Yes No No

Fan Motor Amps Rated Load 0.9 0.9 0.9 1.6 1.5 1.6 1.8

Fan Diameter Inches 18 18 18 18 24 24 24

Rated HP 1/8 1/8 1/8 1/4 1/4 1/4 1/3

Fan Motor

Nominal RPM 1075 1075 1075 1100 860 860 1100

Nominal CFM 2050 2050 2050 2200 3200 3200 4100

Face Area Sq. Ft. 14.1 14.1 14.1 14.1 20 20 24

Coil

Rows Deep 1111111

Fin / Inches 13 13 13 16 13 16 16

Liquid Line OD 3/8 3/8 3/8 3/8 3/8 3/8 3/8

Vapor Line OD 5/8 5/8 3/4 3/4 7/8 7/8 7/8

Unit Charge (Lbs. - Oz.)

4 - 11 4 - 12 5 - 3 5 - 11 7 - 6 7 - 6 9 - 5

Charge Per Foot, Oz. 0.680.680.680.680.700.700.70

Operating Weight Lbs. 158 162 168 173 225 210 246

PHYSICAL AND ELECTRICAL DATA - 3 Phase

MODEL

E4FD036 E4FD048 E4FD060 E4FD036 E4FD048 E4FD060

25 46

Unit Supply Voltage 208/230 - 3 - 60 460 - 3 - 60

Normal Voltage Range

187 TO 253 432 TO 504

Minimum Circuit Ampacity 15.2 20.1 25.0 8.0 9.0 11.4

Max. Overcurrent Device Amps

Compressor Type

Compressor Amps

Rated Load 10.9 14.8 18.5 5.8 6.5 8.3

Locked Rotor 78 91 125 40 46 67

25 30 40 15 15 15

Recip

Scroll

Recip

Scroll

Crankcase Heater Yes No No Yes No No

Fan Motor Amps Rated Load 1.6 1.6 1.8 0.8 0,8 1.0

Fan Diameter Inches 18 24 24 18 24 24

Rated HP 1/4 1/4 1/3 1/4 1/4 1/3

Fan Motor

Nominal RPM 1100 860 1100 1075 860 1100

Nominal CFM 2200 3200 4100 2200 3200 4100

Face Area Sq. Ft. 14.1 20 24 14.1 20 24

Coil

Rows Deep 111111

Fin / Inches 16 16 16 16 16 16

Liquid Line OD 3/8 3/8 3/8 3/8 3/8 3/8

Vapor Line OD 3/4 7/8 7/8 3/4 7/8 7/8

Unit Charge (Lbs. - Oz.)

5 - 11 7 - 6 9 - 5 5 - 11 7 - 6 9 - 5

Charge Per Foot, Oz. 0.68 0.70 0.70 0.68 0.70 0.70

Operating Weight Lbs. 173 210 246 173 210 246

1. Rated in accordance with ARI Standard 110, utilization range “A”.

2. Dual element fuses or HACR circuit breaker.

3. All scrolls listed with a superscript “B” are Bristol scrolls. All scrolls listed with a superscript “C” are Copeland scrolls.

4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.

2 Unitary Products Group

Page 3

036-21030-003 Rev. B (0203)

Additional R-22 Charge / Orifice Size for Various Matched Systems - 1 & 3 Phase

OUTDOOR UNIT E4FD018 E4FD024 E4FD030 E4FD036 E4FD042 E4FD048 E4FD060

Orifice in OD Distributor 37 45 51 59 67 76 76

FACTORY CHARGE, LBS. - OZ. 4-11 4-12 5-3 5-11 7-6 7-6 9-5

ID Orifice included w/Instruction Package 53 61 67 75 78, 81 84, 87 93

INDOOR COIL

COIL ORIFICE

G1FA/G1UA024S14, 17 59 53+2 - - - - - -

G1FA/G1UA030S14 65 53+5 61+0 - - - - -

G1FA/G1UA036S14 73 - 61+2 67+0 - - - -

G1FA/G1UA036S17 73 - - 67+5 - - - -

G1FA/G1UA048S17 84 - - - 75+3 81+5 84+0 -

G1FA/G1UA048S21 84 - - - 75+5 81+5 84+0 -

G1FA/G1UA060S21, 24 90 - - - - - 87+7 93+0

G2FD024(S,H)14, 17 61 53+5 61+0 - - - - -

G2FD030(S,H)17 65 - 61+2 67+0 - - - -

G2FD035(S,H)14 65 - 61+2 67+0 - - - -

G2FD036(S,H)17, 21 75 - - 67+5 75+0 - - -

G2FD042(S,H)21 78 - - 75+1 78+0 - -

G2FD046(S,H)17 78 - - - 75+3 78+0 - -

G2FD048(S,H)21, 24 84 - - - - 81+5 84+2 -

G2FD060(S,H)24 90 - - - - - 87+4 93+0

G2FD061SH24 90 - - - - - - 93+8

G1HD024 59 53+5 61+1 - - - - -

G1HD036 69 - - 67+5 75+0 - - -

G1HD048 81 - - - - 78+2 87+0 -

G1HD060 93 - - - - 81+9 87+0 93+8

F2RP/FP018 53 53+0 - - - - - -

F2RP/FP024 61 53+4 61+0 - - - - -

F2RP/FP030 65 - 61+2 67+0 - - - -

F2RP/FP036 75 - - 67+5 75+0 - - -

F2RP/FP042 78 - - - 75+3 78+0 - -

F2FP048 84 - - - - 81+5 84+2 -

F2FP060 90 - - - - - - 93+0

REFRIGERANT LINE ADDER OZ. / FT. 0.66 0.66 0.68 0.68 0.68 0.70 0.70

FOOTNOTES:

1. These orifices are factory mounted in the flow control device of each indoor coil.

REQUIRED SYSTEM ORIFICE + ADDITIONAL CHARGE, OZ.

PROCEDURES:

1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaportor and for 15 feet of interconnecting line tubing.

2. Verify the orifice size and additional charge required for specific evaportor coil in the system using the above table.

3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above.

4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaportor + adder for line set.

5. If the orifice in the evaportor was change

Unitary Products Group 3

Page 4

036-21030-003 Rev. B (0203)

COOLING CAPACITY - With Air Handler Coils

UNIT

MODEL

AIR HANDLER

ELECTRIC HEAT KW

COIL MODEL

RATED

CFM

NET MBH

TOTAL SENS.

COOLING

SEER

W/O TXV

SEER

+ TXV

1 and 3 Phase 10 SEER HP / N1AH / G2FD

E4FD018 N1AHB08 2,5,7.5,10 17 G2FD024(S,H)17 650 18.4 13.8 11.00 --- 9.10

E4FD024

E4FD030

N1AHB08 2,5,7.5,10 17 G2FD024(S,H)17 800 23.0 17.3 10.45 --- 9.15 N1AHB08 5,7.5,10,15,18 17 G2FD030(S,H)17 800 23.4 17.6 10.50 --- 9.40 N1AHB12 5,7.5,10,15,18 17 G2FD030(S,H)17 1000 29.0 21.8 10.50 --- 9.40 N1AHB12 5,7.5,10,15,18 17 G2FD036(S,H)17 1025 29.4 22.1 11.00 --- 9.40 N1AHB12 5,7.5,10,15,18 17 G2FD036(S,H)17 1220 35.0 26.3 10.00 --- 9.20

E4FD036

N1AHB12 5,7.5,10,15,18 17 G2FD042(S,H)17 1220 35.4 26.6 10.20 --- 9.15 N1AHB12 5,7.5,10,15,18 17 G2FD046(S,H)17 1220 35.4 26.6 10.20 --- 9.15

E4FD042

N1AHC16 5,7.5,10,15,20 21 G2FD042(S,H)21 1400 40.5 30.0 10.00 --- 9.15 N1AHC16 5,7.5,10,15,20 21 G2FD048(S,H)21 1425 41.5 30.7 10.10 --- 9.25 N1AHC16 5,7.5,10,15,20,25,30 21 G2FD048(S,H)21 1600 45.5 33.7 10.50 --- 9.40

E4FD048

N1AHD20 5,7.5,10,15,20,25,30 24 G2FD048(S,H)24 1600 45.5 33.7 10.50 --- 9.40 N1AHD20 5,7.5,10,15,20,25,30 24 G2FD060(S,H)24 1625 47.0 34.8 10.80 --- 9.65

E4FD060 N1AHD20 5,7.5,10,15,20,25,30 24 G2FD060(S,H)24 1800 59.0 44.0 11.00 --- 9.90

1 and 3 Phase 10 SEER HP / N1VS / G2FD

E4FD018 N1VSB12 5,7.5,10,15,18 17 G2FD024(S,H)17 650 19.0 14.3 12.00 --- 10.30

E4FD024

E4FD030

N1VSB12 5,7.5,10,15,18 17 G2FD024(S,H)17 800 23.6 17.7 11.70 --- 10.20 N1VSB12 5,7.5,10,15,18 17 G2FD030(S,H)17 850 24.0 18.0 11.80 --- 10.65 N1VSB12 5,7.5,10,15,18 17 G2FD036(S,H)17 1025 30.0 22.5 11.60 --- 9.30 N1VSB12 5,7.5,10,15,18 17 G2FD030(S,H)17 1025 29.0 21.8 11.30 --- 9.40 N1VSB12 5,7.5,10,15,18 17 G2FD036(S,H)17 1200 35.6 26.7 10.80 --- 9.50

E4FD036

N1VSB16 5,7.5,10,15,20 17 G2FD036(S,H)21 1200 35.6 26.7 11.00 --- 9.70 N1VSB12 5,7.5,10,15,18 17 G2FD046(S,H)17 1200 36.2 27.2 11.00 --- 9.80 N1VSC16 5,7.5,10,15,20 21 G2FD042(S,H)21 1225 36.2 27.2 11.20 --- 10.00

E4FD042 N1VSC16 5,7.5,10,15,20 21 G2FD048(S,H)21 1425 42.0 31.1 11.00 --- 10.00

E4FD048

N1VSC16 5,7.5,10,15,20 21 G2FD048(S,H)21 1600 46.0 34.0 11.00 --- 10.00 N1VSD20 7.5,10,15,20,25,30 24 G2FD060(S,H)24 1625 48.0 35.5 12.00 --- 10.60

E4FD060 N1VSD20 7.5,10,15,20,25,30 24 G2FD060(S,H)24 1800 60.0 45.0 11.50 --- 11.20

1 and 3 Phase 10 SEER HP / F2RP / FP / FV

E4FD018

E4FD024

E4FD030

E4FD036

E4FD042

E4FD048

E4FD060

Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210/240. Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow. EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at a 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions. SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power input in watt-hours during the same period.

1. G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number.

2. Single phase units require single phase 2HK heaters.

3. TXV = Use 1TV700 Series Kit.

4. To meet R=4.2 insulation requirements, substitute F2FP for F2RP, and F2FC for F2RC

5. FG8, FG9, and FL8 furnaces and F2RP / F2FP/F2FV air handlers have B.O.D (Blower on Delay) standard.

- = Not applicable

F2RP/F2FP018 2,5,8 18 --- 650 17.5 13.0 10.70 --- 9.80 F2RP/F2FP024 5,8,10,(10),(15) 18 --- 650 18.8 14.0 10.50 --- 10.45 F2RP/F2FP024 5,8,10,(10),(15) 18 --- 800 22.6 17.0 10.40 --- 9.40 F2RP/F2FP030 5,8,10,15,(10),(15) 18 --- 800 23.2 17.4 10.70 --- 9.50 F2RP/F2FP030 5,8,10,15,(10),(15) 18 --- 1050 29.0 21.8 10.50 --- 9.3 F2RP/F2FP036 5,8,10,15,(10),(15) 18 --- 1050 29.4 22.1 11.00 --- 9.4 F2RP/F2FP036 5,8,10,15,(10),(15) 18 --- 1200 34.2 25.7 10.00 --- 8.90 F2RP/F2FP042 5,8,10,15,(10),(15) 21 --- 1200 35.0 26.3 10.20 --- 9.20 F2RP/F2FP042 5,8,10,15,(10),(15) 21 --- 1500 40.5 30.0 10.00 --- 9.40 F2FP048 10,15, 20, 25, (10),(15) 24 --- 1450 41.5 30.7 10.30 --- 9.65 F2FP048 10,15, 20, 25, (10),(15) 24 --- 1650 46.0 34.0 10.00 --- 9.40 F2FP060 10,15, 20, 25, (10),(15) 24 --- 1800 57.5 43.1 10.00 --- 9.60 F2FV060 10,15, 20, 25, (10),(15) 24 --- 1800 59.0 44.2 11.00 --- 10.50

models. All ratings remain the same.

4,5

EER

4 Unitary Products Group

Page 5

COOLING CAPACITY - Upflow, Downflow, & Horizontal Furnaces and Coils

UNIT MODEL

E4FD018S06

E4FD024S06

E4FD030S06

E4FD036S06

E4FD036S25,46

E4FD042S06

E4FD048S06

For Notes see Page 5.

FURNACE**

CFM RANGE

(MIN.-MAX.)

575 725

750 950

900

1150

1050 1350

1275 1625

1400 1800

14,17 G1FA024S14,17 650 18.5 13.8 10.20 - 10.20

14 G1FA030S14 650 19.0 14.1 10.70 - 10.50

14,17 G1UA024S14,17 650 18.5 13.7 10.50 - 10.20

14 G1UA030S14 650 19.0 14.1 10.70 - 10.50

- G1HD024 650 18.8 14.0 10.50 - 10.45

14,17 G2FD024(S,H)14,17 650 18.8 14.0 10.50 - 10.35

17 G2FD030(S,H)17 650 19.0 14.1 10.50 - 10.50

14 G1FA030S14 850 23.0 17.7 10.00 - 9.15

17,21 G1FA036S17,21 850 23.4 18.0 10.30 - 9.65

14 G1UA030S14 850 23.0 17.7 10.00 - 9.15

17,21 G1UA036S17,21 850 23.4 18.0 10.30 - 9.65

- G1HD024 800 23.0 17.7 10.00 - 9.45

14,17 G2FD024(S,H)14,17 800 23.0 17.7 10.00 - 9.15

17 G2FD030(S,H)17 850 23.4 18.0 10.30 - 9.65

17 G2FD036(S,H)17 850 23.4 18.0 10.25 - 9.35

17,21 G1FA036S17,21 1025 29.0 21.8 10.50 - 9.30

17,21 G1UA036S17,21 1025 29.0 21.8 10.50 - 9.30

- G1HD036 1000 29.0 21.8 10.40 - 9.55

17 G2FD030(S,H)17 1025 29.0 21.8 10.50 - 9.30

14 G2FD035(S,H)14 1000 29.0 21.8 10.50 - 9.30

17 G2FD036(S,H)17 1025 29.4 22.1 11.00 - 9.40

21 G2FD036(S,H)21 1025 29.4 22.1 11.00 - 9.40

21,24 G1FA048S21 1250 35.6 26.7 10.30 - 9.20

21,24 G1UA048S21 1250 35.6 26.7 10.30 - 9.20

17,21 G2FD036(S,H)17,21 1200 35.0 26.3 10.00 - 8.90

21 G2FD042(S,H)21 1200 35.6 26.7 10.30 - 9.20

17 G2FD046(S,H)17 1200 35.6 26.7 10.30 - 9.20

21,24 G1FA048S21 1200 35.6 26.7 10.00 - 9.20

21,24 G1UA048S21 1200 35.6 26.7 10.00 - 9.20

17,21 G2FD036(S,H)17,21 1200 35.0 26.3 10.00 - 8.90

21 G2FD042(S,H)21 1200 35.6 26.7 10.00 - 9.20

17 G2FD046(S,H)17 1200 35.6 26.7 10.00 - 9.20

21,24 G1FA048S21 1450 41.5 30.7 10.50 - 9.70

21,24 G1UA048S21 1450 41.5 30.7 10.50 - 9.70

- G1HD048 1400 41.0 30.3 10.10 - 9.25

- G1HD060 1400 42.5 31.5 10.30 - 9.45

21 G2FD042(S,H)21 1400 40.5 30.0 10.00 - 9.15

17 G2FD046(S,H)17 1450 41.0 30.3 10.00 - 9.20

21,24 G2FD048(S,H)21,24 1450 41.5 30.7 10.10 - 9.25

24 G2FD060(S,H)24 1450 42.0 31.3 10.10 - 9.45

21,24 G1FA048S21 1600 46.0 34.0 10.70 - 9.45

21,24 G1FA060S21,24 1600 47.0 34.8 10.80 - 9.60

21,24 G1UA048S21 1600 46.0 34.0 10.70 - 9.45

21,24 G1UA060S21,24 1600 47.0 34.8 10.80 - 9.60

- G1HD048 1600 45.0 33.3 10.50 - 9.40

- G1HD060 1620 46.5 34.4 10.70 - 9.60

21,24 G2FD048(S,H)21,24 1600 45.5 33.7 10.50 - 9.40

24 G2FD060(S,H)24 1600 47.0 34.8 10.80 - 9.65

COIL

MODEL

RATED

CFM

NET MBH

TOTAL SENS.

036-21030-003 Rev. B (0203)

COOLING

SEER

W/O TXV

SEER + TXV

EER

Unitary Products Group 5

Page 6

036-21030-003 Rev. B (0203)

COOLING CAPACITY - Upflow, Downflow, & Horizontal Furnaces and Coils (Continued)

FURNACE**

UNIT MODEL

CFM RANGE

(MIN.-MAX.)

COIL

MODEL

RATED

21,24 G1FA048S21 1600 46.0 34.0 10.70 - 9.45

21,24 G1FA060S21,24 1600 47.0 34.0 10.80 - 9.60

21,24 G1UA048S21 1600 46.0 34.0 10.70 - 9.45

E4FD048S25,46

1400 1800

21,24 G1UA060S21,24 1600 47.0 34.8 10.80 - 9.60

- G1HD048 1600 45.0 33.3 10.50 - 9.40

- G1HD060 1620 46.5 34.4 10.70 - 9.60

21,24 G2FD048(S,H)21,24 1600 45.5 33.7 10.50 - 9.40

24 G2FD060(S,H)24 1600 47.0 34.8 10.80 - 9.65

21,24 G1FA060S21,24 1800 58.5 43.3 10.50 - 9.90

E4FD060S06

1600 2100

21,24 G1UA060S21,24 1800 58.5 43.3 10.50 - 9.90

- G1HD060 1800 57.0 42.2 10.50 - 9.20

24 G2FD060S24 1800 59.0 43.7 11.00 - 9.90

21,24 G1FA060S21,24 1800 58.5 43.3 10.50 - 9.90

E4FD060S25,46

1600 2100

21,24 G1UA060S21,24 1800 58.5 43.3 10.50 - 9.90

- G1HD060 1800 57.0 42.2 10.50 - 9.20

24 G2FD060(S,H)24 1800 59.0 43.7 11.00 - 9.90

1. TXV = Use 1TV700 Series Kit. * Requires a 2FD Blower Time Delay unless a standard furnace is equipped with one.

Refer to Quick Selection Chart for specific furnace match-up.

CFM

NET MBH

TOTAL SENS.

COOLING

SEER

W/O TXV

SEER + TXV

EER

HEATING PERFORMANCE - With Air Handler and Multi-Position Coils

UNIT

MODEL

COIL

MODEL

ARI HEATING

47° F 17° F HSPF -3°F 7°F 17° F 27°F 37°F 47°F 57°F

MBH COP MBH COP STD VS MBH KW MBH KW MBH KW MBH MBH MBH KW MBH KW MBH KW

OUTDOOR TEMP

1 AND 3 PHASE HP / AIR HANDLERS & COILS

F2RP/F2FP018 17.6 3.00 10 2.00 7.10 -- 4.4 1.09 7.2 1.1 10 1.25 12.4 1.3 15 1.42 17.6 1.53 21 1.75

E4FD018

E4FD024

E4FD030

E4FD036

E4FD042

E4FD048

E4FD060

1. Rated CFM same as for cooling.

2. Heating performance and efficiency is the same for TXV application. Heating MBH based on 70° DB entering indoor air, 72% RH outdoor air with 25

3. Integrated heating capacities include the effect of defrost cycles in the temperature range where they occur.

F2RP/F2FP024 17.8 3.10 10 2.00 7.10 -- 4.8 1.05 7.4 1.09 10 1.25 12.6 1.31 15.6 1.4 17.8 1.5 21.2 1.73 G2FD024(S,H)14, 17 18 3.06 9.9 2.00 7.10 7.2 5 1.02 7.6 1.1 9.9 1.23 12.8 1.32 15.6 1.38 18 1.52 22 1.72 F2RP/F2FP024 22.4 3.10 12.5 2.00 7.35 -- 6.1 1.5 9.3 1.6 12.5 1.75 15.6 1.92 18.8 2.02 22.4 2.13 27.1 2.23 F2RP/F2FP030 22.8 3.20 12.8 2.10 7.40 -- 6.3 1.55 9.4 1.68 12.8 1.68 16 1.9 19 2 22.8 2.14 27.7 2.3 G2FD024(S,H)14, 17 22.4 3.10 12.2 2.00 7.60 7.7 6.3 1.5 9.3 1.5 12.2 1.7 16 1.89 19.2 2.05 22.4 2.12 27 2.4 G2FD030(S,H)17 22.6 3.10 12.4 2.00 7.10 7.2 6.5 1.4 9.6 1.46 12.4 1.7 16 1.92 19 2.07 22.6 2.14 28 2.33 G2FD035(S,H)14 22.4 3.10 12.4 2.00 7.10 -- 6.6 1.5 9.8 1.6 12.4 1.7 16.2 1.9 19.2 2.06 22.4 2.15 28 2.3 F2RP/F2FP030 29 3.20 17 2.30 7.60 -- 10.4 2 13.8 2.1 17 2.23 21.2 2.35 24.8 2.48 29 2.58 34.2 2.68 F2RP/F2FP036 28.4 3.20 17.4 2.30 7.50 -- 10.2 1.95 13.6 2.11 17.4 2.22 22 2.37 24.8 2.5 28.4 2.57 34.6 2.69 G2FD030(S,H)17 29.2 3.20 17 2.30 7.60 7.8 10.4 2 13.8 2.18 17 2.21 21.8 2.4 25 2.6 29.2 2.58 34.2 3.7 G2FD035(S,H)14 29.2 3.20 17 2.30 7.60 -- 10.7 1.98 14 2.15 17 2.23 24 2.42 25.8 2.48 29.2 2.58 34.4 2.65 G2FD036(S,H)17, 21 29.2 3.20 17.4 2.30 7.60 7.7 10.8 2 14.2 2.11 17.4 2.22 24 2.4 25.6 2.48 29.2 2.54 34.6 2.67 F2RP/F2FP036 35.2 3.20 21 2.30 7.50 -- 10.8 2.5 15.4 2.63 21 2.8 24.8 2.95 28.4 3 35.2 3.26 43 3.47 F2RP/F2FP042 35.2 3.20 20 2.10 7.50 -- 10.8 2.5 15.6 2.6 20 2.6 25 2.94 28.6 3 35.2 3.2 43.2 3.4 G2FD042(S,H)21 35 3.20 20 2.10 7.40 7.6 10.8 2.2 15.4 2.62 20 2.6 25 2.76 28.8 2.95 35 3.2 43.2 3.45 G2FD046(S,H)17 35 3.20 20 2.10 7.40 7.6 10.8 2.2 15.8 2.6 20 2.7 25.2 2.76 28.8 2.95 35 3.2 44 3.46 G2FD036(S,H)17, 21 35.2 3.20 21 2.30 7.50 7.6 10.6 2.5 15.4 2.64 21 2.6 25 2.8 28.6 2.98 35.2 3.2 43 3.4 F2RP/F2FP042 39.5 3.20 22.6 2.20 7.4 - 11.7 2.50 17.2 2.76 22.6 3.00 28.0 3.26 33.9 3.50 39.5 3.62 48.7 4.01 F2FP048 40.5 3.30 23.8 2.28 7.5 - 13.1 2.60 18.5 2.84 23.8 3.10 29.1 3.28 35.0 3.50 40.5 3.60 49.8 4.00 G2FD042(S,H)21 39.0 3.24 23.2 2.2 7.4 - 13.4 2.81 18.3 2.95 23.2 3.09 28.1 3.23 33.6 3.39 39.0 3.53 46.7 3.76 G2FD046(S,H)17 39.0 3.28 23.2 2.20 7.4 - 13.0 2.80 18.1 2.92 23.2 3.10 28.3 3.26 33.8 3.40 39.0 3.46 47.8 3.80 G2FD048(S,H)21,24 39.5 3.40 23.4 2.28 7.4 7.5 13.1 2.50 18.2 2.67 23.4 2.90 28.6 3.04 34.2 3.20 39.5 3.31 48.6 3.60 F2FP048 47.0 3.30 28.0 2.3 7.8 - 15.7 3.16 21.8 3.36 28.0 3.57 34.2 3.77 40.9 4.00 47.0 4.17 56.1 4.50 G2FD048(S,H)21,24 47.0 3.50 28.0 2.32 8.0 8.0 16.1 3.30 22.1 3.40 28.0 3.50 33.9 3.67 40.7 3.80 47.0 3.96 54.8 4.20 G2FD060(S,H)24 47.0 3.46 28.0 2.32 8.0 8.0 16.1 3.3 22.0 3.41 28.0 3.50 34.0 3.67 40.7 3.80 47.0 3.94 54.9 4.10 F2FP060 61 3.30 39 2.40 8.20 -- 21.4 4.5 30.1 4.6 39 4.75 43 4.9 52.1 5.1 61 5.3 63 3.47 F2FV060 60 3.30 39 2.40 8.20 -- 21.1 4.3 31 4.7 39 4.8 43.2 4.91 52.3 5.09 60 5.25 63.2 3.4 G2FD060(S,H)24 60 3.40 39 2.40 8.50 8.5 21.1 4.4 26.2 4.6 38 4.7 43 4.85 51.8 5.1 60 5.3 63 3.45

feet of interconnecting piping and no supplemental electric heat operation.

6 Unitary Products Group

Page 7

036-21030-003 Rev. B (0203)

HEATING PERFORMANCE - With Furnace Coils

OUTDOOR TEMP

UNIT

MODEL

COIL

47° F 17° F HSPF -3°F 7°F 17° F 27°F 37°F 47°F 57°F

MBH COP MBH COP STD VS MBH KW MBH KW MBH KW MBH MBH MBH KW MBH KW MBH KW

ARI HEATING

1 AND 3 PHASE EFD / UPFLOW FURNACE & COILS

G1HD024

G1FA024S17

E4FD018

E4FD024

E4FD030

E4FD036

E4FD042

E4FD048

E4FD060

G1UA024S17

G1FA030S14

G1UA030S14

G1HD024

G1FA030S14

G1UA030S14

G1FA036S17,21

G1UA036S17,21

G1HD036

G1FA036S17,21

G1UA036S17,21

G1HD036

G1FA048S21

G1UA048S21

G1HD048

G1HD060

G1FA048S21

G1UA048S21

G1HD048

G1HD060

G1FA048S17,21

G1UA048S17,21

G1FA060S24

G1UA060S24

G1HD060

G1FA060S21,24

G1UA060S21,24

1. Rated CFM same as for cooling.

2. Heating performance and efficiency is the same for TXV application. Heating MBH based on 70° DB entering indoor air, 72% RH outdoor air with 25 feet of interconnecting piping and no supplemental electric heat operation.

3. Integrated heating capacities include the effect of defrost cycles in the temperature range where they occur.

18.2 3.08 9.9 2.00 7.1 - 4.3 1.25 7.1 1.35 9.9 1.45 12.7 1.55 15.5 1.65 18.2 1.73 21.5 1.79

18.0 3.00 9.9 2.00 7.1 - 4.4 1.23 7.2 1.34 9.9 1.45 12.6 1.56 15.5 1.67 18.0 1.76 21.6 1.88

18.2 3.06 9.9 2.00 7.1 - 4.3 1.25 7.1 1.35 9.9 1.45 12.7 1.55 15.5 1.65 18.2 1.74 21.5 1.81

22.0 3.00 12.2 2.00 7.5 - 5.8 1.55 9.0 1.67 12.2 1.8 15.4 1.91 18.6 2.03 22.0 2.15 26.7 2.30

22.0 2.94 12.2 2.00 7.6 - 5.8 1.51 9.0 1.65 12.2 1.79 15.4 1.93 18.6 2.06 22.0 2.19 26.7 2.35

22.4 3.00 12.4 2.00 7.1 - 5.9 1.57 9.1 1.69 12.4 1.82 15.7 1.94 18.9 2.07 22.4 2.19 27.2 2.33

29.6 3.36 18.3 2.36 7.8 - 10.9 2.03 14.6 2.5 18.3 2.27 22.0 2.39 26.0 2.51 29.6 2.58 35.4 2.75

29.2 3.20 17.0 2.30 8.0 - 10.2 1.99 13.9 2.11 17.5 2.23 21.1 2.35 23.7 2.41 28.4 2.55 33.1 2.72

36.4 3.28 20.4 2.38 7.4 - 9.7 2.01 15.1 2.26 20.4 2.51 25.7 2.77 29.7 2.95 36.4 3.25 44.6 3.56

35.0 3.2 20.0 2.10 7.4 - 8.9 1.93 14.7 2.21 20.4 2.49 26.1 2.77 30.0 2.97 37.0 3.29 44.8 3.62

39.5 3.32 23.4 2.28 7.4 - 13.0 2.60 18.2 2.81 23.4 3.01 28.6 3.21 34.2 3.39 39.5 3.49 48.3 3.84

39.5 3.36 23.4 2.28 7.4 - 13.1 2.63 18.3 2.82 23.4 3.01 28.5 3.20 34.2 3.36 39.5 3.45 48.5 3.77

39.5 3.40 23.4 2.34 7.4 - 12.8 2.68 18.1 2.84 23.4 3.01 28.7 3.20 32.8 3.27 40.0 3.49 48.2 3.74

47.0 3.48 28.0 2.32 8.0 - 13.3 2.73 18.4 2.87 23.4 3.01 28.4 3.13 34.2 3.31 39.5 3.45 46.3 3.65

47.0 3.46 28.0 2.32 8.0 - 16.1 3.23 22.0 3.39 28.0 3.54 34.0 3.69 40.7 3.85 47.0 3.98 54.9 4.18

47.0 3.42 28.0 2.30 8.0 - 15.1 3.24 21.5 3.40 28.0 3.57 34.5 3.73 39.1 3.83 47.0 4.03 56.0 4.27

47.0 3.46 28.0 2.32 8.0 - 15.1 3.21 21.5 3.37 28.0 3.54 34.5 3.70 39.1 3.79 47.0 3.98 56.0 4.21

60.0 3.10 38.0 2.40 8.2 - 18.1 4 26.2 4.5 38 4.95 43.1 4.9 52 5.1 60 3.25 72.1 5.9

61.5 3.40 39.0 2.40 8.2 - 18.2 4 26.5 4.4 39 4.98 43.2 4.85 52.1 5.2 61.5 3.26 73.1 5.95

Unitary Products Group 7

Page 8

036-21030-003 Rev. B (0203)

ACCESSORIES

Refer to Price Manual for specific model numbers.

Start Assist Kit (2SA067*)

Blower Time Delay - Available to increase efficiency when

installed. Installs on indoor section and maintains blower for approximately one minute after cooling thermostat has been satisfied.

Hard Start Kits - Provides required starting torque for use with Thermal Expansion Valve Kit.

Low Temperature Cutout (2LT06700224) - Prevents heat pump operation below -10°F ambient temperature.

Compressor Blanket - Designed to further reduce the normal operating sound.

Add-on Control (2AC02700701) - Provides interface for use of gas and oil furnaces with the heat pump system.

Thermal Expansion Valve Kit - 1TV0700 Series TXV kit used to improve system performance.

Outdoor Thermostat (2TD06700124) - Provides additional staging of supplemental electric heat.

Room Thermostats - A wide selection of matching thermostats is available to provide features required for any installation.

2H/1C, manual change-over electronic non-programmable thermostat.

3H/2C, non-programmable digital thermostat.

3H/2C, auto/manual changeover, electronic programmable, 7-day, thermostat.

* For the most current accessory information, refer to the price book or consult factroy.

SOUND RATINGS

EFD

MODEL

018 73

024 74

030 74

036

042

048

060

076

1. Compressor Blanket Factory Installed.

Rated in accordance with ARI Standard 270.

SOUND RATING

DECIBELS*

48" OVERHEAD CLEARANCE

VAPOR CONNECTION

LIQUID CONNECTION

3-1/8

AIR IN 4 SIDES

5-1/2

2-3/8

All dimensions are in inches. They are subject to change without notice. Certified dimensions will be provided upon request.

UNIT

MODEL

EFD

DIMENSIONS

018 30-1/8 24 24

024 30-1/8 24 24

030 30-1/8 24 24

036 30-1/8 24 24

REFRIGERANT

CONNECTION

LINE SIZE

LIQUID VAP OR

5/8

3/8

3/4

042 31-7/8 35 35

7/8048 31-7/8 35 35

060 37-7/8 35 35

8 Unitary Products Group

Page 9

TYPICAL INSTALLATION

036-21030-003 Rev. B (0203)

THERMOSTAT

POWER TO INDOOR BLOWER

TO COIL

NOTE: All outdoor wiring must be weatherproof

SUPPLY

NEC CLASS 2 WIRING

NEC CLASS 1 WIRING

Seal opening(s) with permagum or equivalent

WEATHERPROOF DISCONNECT SWITCH

24” SERVICE ACCESS CLEARANCE

TYPICAL FIELD WIRING - 1 Phase (Air Handler / Electrical Heat)

ALL WIRING TO BE ACCORDANCE WITH NATIONAL CODE AND/OR LOCAL CODES.

THERMOSTAT

7 WIRES

BorC

LorX

TERMINAL NOT USED ON ALL THERMOSTATS.

CHECK THE LOW VOLTAGE TERMINAL BLOCK ON THE INDOOR UNIT FOR THE ACTUAL ARRANGEMENT OF THE TERMINALS.

CONNECT POWER WIRING TO TERMINAL BLOCK 3TB ON UNITS WITHOUT ELECTRIC HEAT OR CIRCUIT BREAKER.

POWER WIRING

24V CONTROL WIRING (NEC CLASS 2)

IN AIR HANDLER WITH ELECTRIC HEAT

INDOOR UNIT

LOW VOLTAGE TERMINAL BLOCK

R C Y O W2

W1 BK

DEHUMIDIFICATION CONTROL CONNECTION (”Humidistat” Jumper must be removed).

CIRCUIT BREAKER

GND. LUG

48” OVERHEAD CLEARANCE

12” REAR AND SIDES

OUTDOOR

3,4

UNIT

R C Y O W X W1

CONTACTOR

POWER WIRING

208/230-1-60

GND.

SCREW

TYPICAL FIELD WIRING - 3 Phase (Air Handler / Electrical Heat)

INDOOR UNIT

GND. LUG

Unitary Products Group 9

POWER WIRING

POWER

SUPPLY

208/230-3-60

460-3-60

OUTDOOR UNIT

CONTACTOR

POWER WIRING

208/230-3-60

460-3-60

GND. SCREW

Page 10

036-21030-003 Rev. B (0203)

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E4FD018S06

INDOOR COIL MODEL NO. F2RP/F2FP018

CONDENSER

ENTERING AIR

TEMPERATURE

105

115

125

ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM 600 650 700

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 22.3 20.4 18.6 17.0 22.4 20.6 18.8 17.2 22.6 20.7 18.9 17.4

S.C. 14.7 14.8 14.9 15.1 15.2 15.3 15.5 15.6 15.8 15.8 15.9 16.1

K.W 1.51 1.54 1.54 1.53 1.52 1.56 1.56 1.56 1.56 1.59 1.61 1.60

T.C. 21.0 19.2 17.4 15.9 21.2 19.3 17.5 16.1 21.3 19.4 17.6 16.3

S.C. 14.0 14.0 14.1 14.3 14.5 14.4 14.6 14.8 14.9 14.9 15.0 15.2

K.W 1.59 1.60 1.58 1.56 1.61 1.62 1.61 1.58 1.65 1.66 1.65 1.62

T.C. 19.4 17.6 15.9 14.6 19.5 17.8 16.0 14.8 19.7 17.9 16.1 14.9

S.C. 13.0 12.9 13.0 13.2 13.4 13.4 13.4 13.6 13.8 13.8 13.8 14.0

K.W 1.70 1.68 1.65 1.62 1.72 1.70 1.67 1.64 1.76 1.75 1.72 1.69

T.C. 17.6 15.7 14.2 12.7 17.6 16.0 14.3 12.9 17.8 16.1 14.4 13.3

S.C. 11.7 11.6 11.6 11.2 11.9 12.0 12.0 11.5 12.3 12.4 12.3 12.5

K.W 1.80 1.75 1.72 1.69 1.82 1.80 1.74 1.71 1.86 1.85 1.78 1.74

T.C. 15.8 13.8 12.5 10.8 15.7 14.2 12.6 11.0 15.9 14.3 12.7 11.7

S.C. 10.4 10.3 10.2 9.2 10.4 10.6 10.6 9.4 10.8 11.0 10.8 11.0

K.W 1.90 1.82 1.79 1.76 1.92 1.90 1.81 1.78 1.96 1.95 1.84 1.79

T.C. 14.0 11.9 10.8 8.9 13.8 12.4 10.9 9.1 14.0 12.5 11.0 10.1

S.C. 9.19.08.87.28.99.29.27.39.39.69.39.5

K.W 2.00 1.89 1.86 1.83 2.02 2.00 1.88 1.85 2.06 2.05 1.90 1.84

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.

Air Handler Coil

N1AHB08 G2FD024(S,H)17 1.03 1.03 1.00

N1VSB12 G2FD024(S,H)17 1.07 1.07 1.00

F2RP/F2FP024 1.01 1.01 1.06

G1UA024S14 1.02 1.02 1.06

G1UA024S17 1.02 1.02 1.06

G2FD024(S,H)14 1.03 1.03 1.06

G2FD024(S,H)17 1.03 1.03 1.06

G1UA030S14 1.03 1.03 1.06

G1HD024 1.01 1.01 1.06

G1FA024S14 1.02 1.02 1.06

G1FA024S17 1.02 1.02 1.06

G1FA030S14 1.03 1.03 1.06

T.C. S.C. KW

10 Unitary Products Group

Page 11

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E4FD024S06

INDOOR COIL MODEL NO. F2RP/F2FP024

CONDENSER

ENTERING AIR

TEMPERATURE

105

115

125

ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM 750 800 850

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 27.0 24.8 22.6 20.4 27.3 25.3 22.7 20.5 27.9 25.2 22.9 20.7

S.C. 17.3 17.3 17.5 17.2 17.5 17.9 17.7 17.6 18.2 18.0 18.1 18.0

K.W 1.94 1.91 1.87 1.81 1.97 1.93 1.88 1.83 2.01 0.43 1.91 1.86

T.C. 26.7 24.3 22.0 19.9 26.6 24.5 22.0 19.8 26.8 24.4 22.1 20.2

S.C. 17.4 17.3 17.4 17.3 17.5 17.7 17.5 17.4 17.8 17.8 17.9 18.1

K.W 2.12 2.06 2.00 1.94 2.13 2.08 2.01 1.92 2.16 2.11 2.05 1.99

T.C. 24.7 22.5 20.3 18.3 24.9 22.6 20.4 18.4 24.9 22.7 20.5 18.8

S.C. 16.7 16.7 16.7 16.6 17.1 17.0 17.1 17.0 17.4 17.4 17.5 17.8

K.W 2.24 2.18 2.12 2.05 2.26 2.20 2.13 2.06 2.30 2.24 2.17 2.11

T.C. 22.5 20.5 18.4 17.0 22.6 20.6 18.6 17.0 22.7 20.7 18.6 17.1

S.C. 16.1 16.0 16.0 16.3 16.5 16.4 16.5 16.5 16.9 16.8 16.7 16.9

K.W 2.38 2.30 2.23 2.16 2.39 2.32 2.24 2.20 2.42 2.36 2.29 2.24

T.C. 20.3 18.4 16.9 15.2 20.4 18.4 17.0 15.6 20.4 18.5 17.1 15.8

S.C. 15.5 15.4 15.8 15.4 16.0 15.7 16.2 16.2 16.2 16.2 16.6 16.4

K.W 2.51 2.43 2.36 2.28 2.52 2.45 2.38 2.30 2.57 2.49 2.41 2.34

T.C. 18.1 16.3 15.4 13.4 18.2 16.2 15.4 14.2 18.1 16.3 15.6 14.5

S.C. 24.5 20.8 17.8 14.1 24.3 20.4 17.5 14.7 23.9 20.2 17.5 14.7

K.W 2.64 2.56 2.49 2.40 2.65 2.58 2.52 2.40 2.72 2.62 2.53 2.44

036-21030-003 Rev. B (0203)

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHB08 G2FD024(S,H)17 1.02 1.02 1.00

N1AHB08 G2FD030(S,H)17 1.04 1.04 1.00

N1AHB08 G2FD035(S,H)14 1.04 1.04 1.00

N1VSB12 G2FD024(S,H)17 1.04 1.04 0.91

N1VSB12 G2FD030(S,H)17 1.06 1.06 0.95

F2RP/F2FP030 1.03 1.02 1.05

G2FD024(S,H)14 1.02 1.05 1.00

G2FD024(S,H)17 1.02 1.05 1.00

G1HD024 1.02 1.02 1.00

G1UA030S14 1.02 1.02 1.00

G1UA036S17 1.04 1.04 1.00

G1UA036S21 1.04 1.04 1.00

G2FD030(S,H)17 1.04 1.04 1.00

G2FD035(S,H)14 1.04 1.04 1.00

G1FA030S14 1.02 1.02 1.00

G1FA036S17 1.04 1.04 1.00

G1FA036S21 1.04 1.04 1.00

T.C. S.C. KW

Unitary Products Group 11

Page 12

036-21030-003 Rev. B (0203)

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E4FD030S06

INDOOR COIL MODEL NO. F2RP/F2FP030

CONDENSER

ENTERING AIR

TEMPERATURE

105

115

125

ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM 1000 1050 1100

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 34.3 31.3 28.4 25.6 34.8 31.8 28.8 26.0 35.1 32.1 29.1 26.3

S.C. 21.4 21.3 21.4 21.3 22.2 22.1 22.2 22.1 22.8 22.8 22.9 22.8

K.W 2.37 2.30 2.22 2.15 2.41 2.34 2.27 2.20 2.46 2.38 2.31 2.24

T.C. 33.5 30.6 27.7 25.0 34.0 31.1 28.1 25.4 34.3 31.3 28.4 25.6

S.C. 21.3 21.3 21.3 21.3 22.2 22.2 22.2 22.2 23.0 22.9 23.0 23.0

K.W 2.63 2.55 2.46 2.37 2.68 2.60 2.50 2.42 2.72 2.64 2.55 2.46

T.C. 31.4 28.6 25.9 23.4 31.8 29.0 26.3 24.1 32.0 29.3 26.5 24.5

S.C. 20.9 20.8 21.0 20.9 21.8 21.8 22.0 22.4 22.7 22.7 22.9 23.2

K.W 2.84 2.75 2.65 2.56 2.89 2.80 2.70 2.62 2.93 2.84 2.74 2.67

T.C. 28.9 26.4 23.9 21.9 29.2 26.7 24.5 22.2 29.4 26.9 24.8 22.9

S.C. 20.4 20.3 20.6 20.8 21.4 21.3 22.0 21.7 22.4 22.3 22.9 23.1

K.W 3.05 2.95 2.84 2.75 3.09 3.00 2.90 2.80 3.14 3.04 2.95 2.87

T.C. 26.3 24.0 21.9 20.2 26.5 24.2 22.2 20.6 26.6 24.6 22.4 21.0

S.C. 19.8 19.7 20.1 20.3 20.9 20.9 21.0 20.7 21.9 22.1 21.9 21.1

K.W 3.24 3.13 3.03 2.94 3.29 3.18 3.08 3.00 3.33 3.23 3.13 3.06

T.C. 23.7 21.6 19.9 18.5 23.8 21.7 19.9 19.0 23.8 22.3 20.0 19.1

S.C. 19.2 19.1 19.6 19.8 20.4 20.5 20.0 19.7 21.4 21.9 20.9 19.1

K.W 3.43 3.31 3.22 3.13 3.49 3.36 3.26 3.20 3.52 3.42 3.31 3.25

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHB12 G2FD030(S,H)17 1.00 1.00 1.04

N1AHB12 G2FD035(S,H)14 1.00 1.00 1.04

N1AHB12 G2FD036(S,H)17 1.01 1.01 1.04

N1AHB12 G2FD036(S,H)21 1.01 1.01 1.04

N1VSB12 G2FD036(S,H)17 1.03 1.03 1.04

N1VSB12 G2FD030(S,H)17 1.00 1.00 1.04

F2RP/F2FP036 1.01 1.01 1.04

G2FD030(S,H)17 1.00 1.00 1.00

G2FD035(S,H)14 1.00 1.00 1.04

G1UA036S17 1.00 1.00 1.00

G1UA036S21 1.00 1.00 1.00

G2FD036(S,H)21 1.01 1.01 1.04

G2FD036(S,H)17 1.01 1.01 1.04

G1HD036 1.00 1.00 1.00

G1FA036S17 1.00 1.00 1.00

G1FA036S21 1.00 1.00 1.00

T.C. S.C. KW

12 Unitary Products Group

Page 13

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E4FD036S06, E4FD036S25, 46

INDOOR COIL MODEL NO. F2RP/F2FP036

CONDENSER

ENTERING AIR

TEMPERATURE

105

115

125

ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM 1100 1200 1300

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 40.6 37.3 34.1 31.0 41.0 37.7 34.4 31.4 40.9 37.6 34.7 31.6

S.C. 24.5 24.5 24.8 24.7 25.2 25.2 25.5 25.4 25.4 25.4 26.1 26.1

K.W 3.05 2.98 2.90 2.82 3.09 3.02 2.94 2.86 3.19 3.11 3.04 2.96

T.C. 39.8 36.6 33.4 30.4 40.2 37.0 33.7 31.0 40.5 37.2 34.0 31.3

S.C. 25.0 25.1 25.3 25.4 25.8 25.9 26.2 26.6 26.7 26.7 27.1 27.4

K.W 3.34 3.24 3.15 3.05 3.38 3.29 3.19 3.10 3.48 3.39 3.29 3.21

T.C. 36.9 33.9 30.9 28.3 37.2 34.2 31.4 28.6 37.4 34.4 31.6 29.0

S.C. 24.6 24.7 25.0 25.1 25.6 25.7 26.1 26.0 26.6 26.6 27.0 27.2

K.W 3.56 3.46 3.35 3.25 3.60 3.50 3.40 3.30 3.70 3.60 3.50 3.40

T.C. 33.2 30.6 27.9 25.5 33.4 30.8 28.1 26.0 33.7 31.0 28.4 26.4

S.C. 24.0 24.0 24.2 24.1 25.0 25.1 25.2 25.3 26.1 26.1 26.3 25.7

K.W 3.78 3.68 3.56 3.45 3.83 3.72 3.61 3.51 3.93 3.82 3.71 3.62

T.C. 29.2 26.9 24.6 22.8 29.4 27.1 24.8 23.2 29.5 27.3 25.2 23.5

S.C. 22.6 22.7 22.7 22.2 23.7 23.7 23.8 22.5 24.7 24.7 24.5 22.8

K.W 3.99 3.86 3.75 3.64 4.03 3.90 3.79 3.70 4.13 4.00 3.91 3.82

T.C. 25.2 23.2 21.3 20.1 25.4 23.4 21.5 20.4 25.3 23.6 22.0 20.6

S.C. 21.2 21.4 21.2 20.3 22.4 22.3 22.4 19.7 23.3 23.3 22.7 19.9

K.W 4.20 4.04 3.94 3.83 4.23 4.08 3.97 3.89 4.33 4.18 4.11 4.02

036-21030-003 Rev. B (0203)

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHB12 G2FD036(S,H)17 1.02 1.02 1.00

N1AHB12 G2FD036(S,H)21 1.02 1.02 1.00

N1AHB12 G2FD042(S,H)17 1.04 1.04 1.00

N1AHB12 G2FD046(S,H)17 1.04 1.04 1.00

N1VSB12 G2FD036(S,H)17 1.04 1.04 0.89

N1VSB16 G2FD036(S,H)21 1.04 1.04 0.89

N1VSB12 G2FD046(S,H)17 1.06 1.06 0.91

N1VSC16 G2FD042(S,H)21 1.06 1.06 0.91

F2RP/F2FP042 1.02 1.02 0.97

G1UA048S17 1.04 1.04 1.00

G1UA048S21 1.04 1.04 1.00

G1HD036 1.02 1.02 1.00

G2FD036(S,H)17 1.02 1.02 0.97

G2FD036(S,H)21 1.02 1.02 1.00

G2FD042(S,H)21 1.04 1.04 1.00

G2FD046(S,H)17 1.04 1.04 1.00

G1HD036 1.02 1.02 0.80

G1FA048S17 1.04 1.04 1.00

G1FA048S21 1.04 1.04 1.00

T.C. S.C. KW

Unitary Products Group 13

Page 14

036-21030-003 Rev. B (0203)

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E4FD042S06

INDOOR COIL MODEL NO. F2RP/F2FP042

CONDENSER

ENTERING AIR

TEMPERATURE

105

115

125

ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM 1400 1500 1600

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 47.0 42.9 38.8 35.0 47.4 43.2 39.1 35.7 47.6 43.5 39.4 36.0

S.C. 28.8 28.8 29.0 28.9 29.6 29.6 29.8 30.2 30.3 30.3 30.5 30.8

K.W 3.69 3.58 3.46 3.34 3.75 3.63 3.51 3.41 3.82 3.70 3.58 3.48

T.C. 46.4 42.3 38.2 34.7 46.7 42.6 38.5 35.0 46.9 42.8 38.7 35.3

S.C. 29.3 29.3 29.5 29.6 30.1 30.1 30.3 30.5 31.0 30.9 31.2 31.3

K.W 3.98 3.84 3.70 3.58 4.04 3.90 3.76 3.64 4.11 3.97 3.83 3.71

T.C. 44.1 40.2 36.3 32.9 44.5 40.5 36.7 33.2 44.6 40.6 37.0 33.6

S.C. 28.9 28.9 29.2 29.2 30.0 30.0 30.3 30.1 30.8 30.8 31.2 31.1

K.W 42.00 4.25 4.08 3.93 4.47 4.31 4.14 3.99 4.55 4.39 4.22 4.08

T.C. 41.3 37.6 34.0 30.8 41.5 37.8 34.3 31.1 41.6 38.0 34.4 31.8

S.C. 28.3 28.3 28.5 28.4 29.3 29.3 29.6 29.2 30.2 30.2 30.4 30.4

K.W 4.88 4.68 4.49 4.31 4.94 4.74 4.55 4.38 5.02 4.82 4.63 4.48

T.C. 38.1 34.7 31.4 28.8 38.3 34.9 31.6 29.2 38.5 35.0 31.8 29.5

S.C. 27.3 27.3 27.4 27.6 28.3 28.3 28.3 28.0 29.4 29.1 29.2 28.3

K.W 5.36 4.13 4.91 4.73 5.42 5.20 4.98 4.83 5.49 5.28 5.07 4.91

T.C. 34.9 31.8 28.8 26.8 35.1 32.0 28.9 27.3 35.4 32.0 29.2 27.2

S.C. 26.3 26.3 26.3 26.8 27.3 27.3 27.0 26.8 28.6 28.0 28.0 26.2

K.W 5.84 3.58 5.33 5.15 5.90 5.66 5.41 5.28 5.96 5.74 5.51 5.34

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHC16 G2FD042(S,H)21 1.00 1.00 1.03

N1AHC16 G2FD048(S,H)21 1.02 1.02 1.04

N1VSC16 G2FD048(S,H)21 1.04 1.04 0.97

F2FP048 1.02 1.02 1.00

G2FD042(S,H)21 1.00 1.00 1.03

G1UA048S21 1.02 1.02 0.99

G1HD048S 1.01 1.01 1.03

G2FD046(S,H)17 1.01 1.01 1.03

G1HD060S 1.05 1.05 1.04

G2FD048(S,H)21 1.02 1.02 1.04

G2FD048(S,H)24 1.02 1.02 1.04

G1FA048S21 1.02 1.02 0.99

T.C. S.C. KW

14 Unitary Products Group

Page 15

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E4FD048S06, E4FD048S25, 46

INDOOR COIL MODEL NO. F2FP048

CONDENSER

ENTERING AIR

TEMPERATURE

105

115

125

ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM 1450 1650 1750

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 54.3 50.2 46.1 42.3 55.0 50.8 46.6 42.8 55.4 51.2 47.1 43.5

S.C. 33.3 33.6 34.1 34.3 34.7 35.0 35.5 35.6 36.0 36.2 36.8 37.4

K.W 4.15 4.09 4.02 3.96 4.25 4.18 4.11 4.05 4.48 4.41 4.34 4.28

T.C. 52.6 48.6 44.6 40.9 53.1 49.1 45.0 41.5 53.5 49.5 45.5 42.0

S.C. 33.2 33.4 33.9 34.1 34.7 34.9 35.3 35.8 36.0 36.2 36.9 37.2

K.W 4.48 4.41 4.33 4.30 4.57 4.50 4.43 4.37 4.81 4.73 4.69 4.59

T.C. 49.5 45.7 41.8 38.5 49.8 46.0 42.4 39.0 50.1 46.3 42.7 39.3

S.C. 32.5 32.7 32.9 33.3 33.8 34.0 34.7 34.8 35.4 35.6 36.2 36.2

K.W 4.84 4.77 4.71 4.63 4.95 4.88 4.80 4.73 5.18 5.10 5.02 4.95

T.C. 45.8 42.3 38.9 35.7 46.3 42.6 39.3 36.2 46.4 43.0 39.6 37.4

S.C. 31.2 31.4 32.0 32.1 33.1 33.0 33.5 33.7 34.4 34.7 35.0 35.8

K.W 5.29 5.20 5.11 5.04 5.35 5.29 5.21 5.15 5.61 5.51 5.44 5.41

T.C. 42.0 38.9 35.8 33.0 42.4 39.3 36.1 34.1 42.4 39.3 36.5 34.6

S.C. 29.8 30.2 30.6 30.8 31.7 31.9 32.2 32.7 32.9 32.8 33.8 33.2

K.W 5.78 5.65 5.58 5.52 5.84 5.75 5.68 5.61 6.13 6.06 5.91 5.84

T.C. 38.2 35.5 32.7 30.3 38.5 36.0 32.9 32.0 38.4 35.6 33.4 31.8

S.C. 28.4 29.0 29.2 29.5 30.3 30.8 30.9 31.7 31.4 30.9 32.6 30.6

K.W 6.27 6.10 6.05 6.00 6.33 6.21 6.15 6.07 6.65 6.61 6.38 6.27

036-21030-003 Rev. B (0203)

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHC16 G2FD048(S,H)21 0.99 0.99 0.99

N1AHD20 G2FD048(S,H)24 0.99 0.99 0.99

N1AHD20 G2FD060(S,H)24 1.02 1.02 1.00

N1VSC16 G2FD048(S,H)21 1.00 1.00 0.94

N1VSD20 G2FD060(S,H)24 1.04 1.04 0.93

G1HD048S 0.98 0.98 0.98

G2FD048(S,H)21 0.99 0.99 0.99

G2FD048(S,H)24 0.99 0.99 0.99

G1UA048S21 1.00 1.00 1.00

G1UA060S21 1.02 1.02 1.00

G1UA060S24 1.02 1.02 1.00

G2FD060(S,H)24 1.02 1.02 1.00

G1HD060 1.01 1.01 0.99

G1FA048S21 1.00 1.00 1.00

G1FA060S21 1.02 1.02 1.00

G1FA060S24 1.02 1.02 1.00

T.C. S.C. KW

Unitary Products Group 15

Page 16

036-21030-003 Rev. B (0203)

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E4FD060S06, E4FD060S25,46

INDOOR COIL MODEL NO. F2FP060

CONDENSER

ENTERING AIR

TEMPERATURE

105

115

125

ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 65.4 60.2 55.2 50.3 66.2 60.9 55.7 50.9 66.8 61.5 56.3 51.7

S.C. 41.5 41.7 42.4 42.5 43.0 43.2 43.9 44.0 44.4 44.5 45.4 45.8

K.W 5.23 5.13 5.04 4.96 5.24 5.15 5.06 4.97 5.27 5.18 5.07 5.02

T.C. 64.5 59.3 54.1 49.3 65.2 59.9 54.8 50.1 65.8 60.5 55.3 50.7

S.C. 41.7 41.9 42.5 42.6 43.5 43.7 44.2 44.5 45.1 45.3 45.7 46.1

K.W 5.68 5.57 5.46 5.36 5.68 5.58 5.48 5.39 5.71 5.59 5.49 5.40

T.C. 62.0 56.9 51.8 47.3 62.6 57.5 52.4 48.0 63.1 58.0 53.0 48.4

S.C. 41.2 41.4 41.8 42.0 42.9 43.1 43.6 44.0 44.7 44.8 45.5 45.5

K.W 6.09 5.98 5.87 5.76 6.10 5.99 5.88 5.77 6.11 6.01 5.90 5.80

T.C. 59.0 54.0 49.1 44.8 59.4 54.6 49.7 45.3 59.6 54.9 50.2 45.9

S.C. 40.4 40.4 40.8 41.0 42.0 42.3 52.5 42.8 43.7 44.0 44.4 44.8

K.W 6.50 6.40 6.28 6.17 6.53 6.41 6.29 6.18 6.57 6.43 6.31 6.20

T.C. 55.6 50.2 46.4 42.2 56.0 51.5 46.9 42.7 56.2 51.7 47.3 43.4

S.C. 39.3 38.8 39.7 39.7 40.9 41.1 41.4 41.4 42.7 42.8 43.0 43.3

K.W 6.95 6.72 6.71 6.60 6.97 6.85 6.74 6.61 7.02 6.86 6.76 6.63

T.C. 52.3 46.4 43.7 39.6 52.7 48.3 44.1 40.1 52.8 48.6 44.3 40.8

S.C. 38.2 37.2 38.5 38.3 39.9 40.0 30.4 40.1 41.7 41.6 41.6 41.8

K.W 7.40 7.05 7.14 7.03 7.41 7.29 7.18 7.04 7.47 7.29 7.21 7.06

1650 1800 1950

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

F2FV060 1.03 1.03 1.00

N1VSD20 G2FD060(S,H)24 1.04 1.04 0.94

N1AHD2006 G2FD060(S,H)24 1.03 1.02 0.89

G1FA060S21, 1.00 0.99 1.00

G1HD060 0.99 0.99 0.99

G1UA060S21, 1.02 1.02 1.04

G2FD060(S,H)24 1.03 1.02 0.99

T.C. S.C. KW

16 Unitary Products Group

Page 17

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E4FD018S06

EVAPORATOR COIL MODEL NO F2RP/F2FP018

AIR TEMP. ENTERING OUTDOOR

UNIT

NOTE:

ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR

COIL

60 21.11.783.5621.71.783.6621.91.654.00

70 20.01.813.3320.91.833.4321.31.703.76

80 18.91.843.0820.01.883.2020.51.763.50

60 18.31.653.2618.51.673.2518.71.573.48

70 17.11.702.9517.61.723.0017.91.613.25

80 15.71.752.6416.61.772.7417.01.653.01

60 14.81.323.2516.81.613.0317.51.513.36

70 13.71.502.6615.81.662.7715.71.562.92

80 12.72.001.8414.71.722.5013.91.892.14

60 14.01.522.6714.41.532.7214.11.402.91

70 12.81.562.3713.31.582.4313.41.472.63

80 11.5 1.60 2.07 12.1 1.64 2.15 12.6 1.55 2.35

60 10.6 1.40 2.23 11.2 1.42 2.32 11.4 1.35 2.49

70 9.4 1.481.8710.01.472.0010.31.432.12

80 8.2 1.58 1.53 8.8 1.53 1.69 9.2 1.52 1.77

60 9.0 1.34 2.04 9.5 1.37 2.10 9.9 1.29 2.32

70 7.6 1.37 1.68 8.2 1.41 1.77 8.7 1.34 1.97

80 6.2 1.42 1.33 7.0 1.47 1.45 7.6 1.40 1.65

MBTUH

600 650 700

K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.

036-21030-003 Rev. B (0203)

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

F2RP/F2FP024 1.01 0.98 1.03

G2FD024(S,H)14,17 1.02 1.00 1.02

G1HD024 1.03 1.01 1.03

G1UA024S17 1.02 1.02 1.00

G1UA030S14 1.03 1.01 1.02

G1FA024S17 1.02 1.02 1.00

G1FA030S14 1.03 1.03 1.00

T.C. S.C. KW

Unitary Products Group 17

Page 18

036-21030-003 Rev. B (0203)

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E4FD024S06

EVAPORATOR COIL MODEL NO F2RP/F2FP024

AIR TEMP. ENTERING OUTDOOR

UNIT

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

AIR TEMP. ENTERING

INDOOR

COIL

60 27.2 2.21 3.72 27.4 2.17 3.80 27.0 1.97 4.12

70 26.1 2.27 3.46 26.7 2.25 3.58 26.5 2.04 3.90

80 25.0 2.48 3.03 25.9 2.47 3.16 26.0 2.26 3.47

60 23.2 2.01 3.39 23.2 2.05 3.32 23.7 1.90 3.66

70 22.0 2.07 3.13 22.4 2.12 3.10 23.2 1.98 3.44

80 20.8 2.23 2.74 21.6 2.30 2.76 22.6 2.15 3.08

60 18.4 1.63 3.27 21.0 1.99 3.06 21.8 1.87 3.39

70 17.4 1.86 2.73 20.1 2.05 2.84 19.9 1.93 3.00

80 16.5 2.56 1.88 19.2 2.20 2.54 18.1 2.42 2.18

60 17.2 1.89 2.63 17.7 1.91 2.68 17.3 1.75 2.86

70 16.1 1.93 2.41 16.8 1.96 2.48 16.9 1.82 2.67

80 15.0 2.02 2.15 15.9 2.06 2.22 16.4 1.95 2.44

60 13.0 1.73 2.20 13.5 1.80 2.20 14.0 1.67 2.45

70 12.0 1.75 2.01 12.5 1.83 2.00 13.1 1.70 2.25

80 10.9 1.76 1.82 11.5 1.86 1.81 12.2 1.72 2.07

60 10.8 1.72 1.89 11.2 1.75 1.93 11.7 1.64 2.14

70 9.5 1.721.6710.21.761.7410.41.671.88

80 8.2 1.67 1.48 9.1 1.73 1.59 9.1 1.65 1.67

MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.

750 800 850

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

F2RP/F2FP030 1.02 0.99 1.03

G2FD035(S,H)14 1.00 1.00 1.00

G2FD030(S,H)17 1.01 1.01 1.00

G2FD024(S,H)14,17 1.00 1.00 1.00

G1HD024 0.98 1.01 0.97

G1UA030S14 0.98 1.04 0.95

G1UA036S17,21 1.00 1.03 0.97

G1FA030S14 0.98 1.04 0.95

G1FA036S17,21 1.00 1.03 0.97

T.C. S.C. KW

18 Unitary Products Group

Page 19

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E4FD030S06

EVAPORATOR COIL MODEL NO F2RP/F2FP030

AIR TEMP. ENTERING OUTDOOR

UNIT

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR

COIL

60 34.52.763.7734.82.753.8234.92.733.86

70 33.02.863.4734.22.873.5934.72.883.64

80 31.72.943.2433.82.973.4334.63.003.49

60 29.62.553.4129.92.553.4430.12.553.46

70 28.0 2.64 3.11 29.0 2.66 3.20 29.5 2.68 3.23

80 26.52.722.8628.22.753.0129.02.783.06

60 26.82.413.2227.62.463.2727.82.483.26

70 25.32.512.9326.22.552.9926.52.572.99

80 23.92.622.6524.82.642.7325.22.672.74

60 23.22.302.9124.12.322.9924.52.353.00

70 21.22.352.6122.22.382.6922.82.422.71

80 19.22.422.2920.32.472.3821.02.522.41

60 18.2 2.07 2.58 18.5 2.11 2.57 18.8 2.17 2.54

70 16.52.132.2717.02.172.3017.42.222.30

80 14.72.191.9815.52.232.0416.02.272.07

60 15.01.982.2915.82.022.3716.42.082.39

70 13.6 2.01 2.04 14.2 2.06 2.09 14.8 2.11 2.12

80 12.12.051.7912.52.091.8213.22.141.86

MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.

1000 1050 1100

036-21030-003 Rev. B (0203)

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

F2RP/F2FP036 0.98 0.98 1.00

G2FD035(S,H)14 1.01 1.01 1.00

G1FD030S17 1.01 1.01 1.00

G1FD036S17,21 1.01 1.01 1.00

G1HD036 1.02 0.97 1.05

G1UA036S17,21 1.01 1.01 1.00

G1FA036S17,21 1.01 1.01 1.00

T.C. S.C. KW

Unitary Products Group 19

Page 20

036-21030-003 Rev. B (0203)

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E4FD036S06, E4FD036S25, 46

EVAPORATOR COIL MODEL NO F2RP/F2FP036

AIR TEMP. ENTERING OUTDOOR

UNIT

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

AIR TEMP. ENTERING

INDOOR

COIL

60 42.8 3.34 3.85 43.2 3.28 3.97 42.5 3.25 3.94

70 40.3 3.52 3.45 41.4 3.47 3.59 41.4 3.46 3.60

80 38.5 3.68 3.16 40.2 3.65 3.32 40.9 3.66 3.37

60 36.6 3.09 3.48 37.0 3.07 3.54 36.1 3.06 3.46

70 34.4 3.23 3.12 35.2 3.23 3.20 35.1 3.23 3.18

80 32.6 3.36 2.85 33.9 3.38 2.95 34.5 3.40 2.98

60 32.7 2.97 3.20 33.7 2.98 3.29 34.5 2.99 3.35

70 31.0 3.09 2.92 31.9 3.10 2.99 32.8 3.12 3.06

80 29.3 3.22 2.65 30.2 3.24 2.71 31.2 3.26 2.78

60 27.5 2.80 2.84 28.9 2.84 2.94 29.0 2.86 2.92

70 25.8 2.87 2.60 27.2 2.92 2.69 27.5 2.94 2.70

80 23.6 2.97 2.30 25.1 3.03 2.39 25.6 3.06 2.42

60 22.0 2.55 2.53 22.5 2.60 2.54 22.6 2.63 2.52

70 20.3 2.62 2.27 21.0 2.68 2.30 21.3 2.71 2.30

80 18.5 2.68 2.03 19.4 2.75 2.08 19.8 2.78 2.10

60 18.4 2.44 2.28 19.2 2.50 2.31 19.5 2.54 2.31

70 16.7 2.48 2.03 17.7 2.55 2.09 18.0 2.59 2.10

80 15.0 2.51 1.80 16.1 2.59 1.88 16.5 2.62 1.89

MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.

1100 1200 1300

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

F2RP/F2FP042 1.00 1.00 1.00

G2FD036(S,H)17 1.00 1.00 1.00

G2FD036(S,H)21 1.00 1.00 1.00

G2FD042(S,H)21 0.99 0.99 1.00

G2FD046(S,H)17 0.99 0.99 1.00

G1HD036 1.03 1.01 1.02

G1UA048S21 0.99 0.99 1.00

G1FA048S21 0.99 0.99 1.00

T.C. S.C. KW

20 Unitary Products Group

Page 21

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E4FD042S06

EVAPORATOR COIL MODEL NO F2RP/F2FP042

AIR TEMP. ENTERING OUTDOOR

UNIT

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR

COIL

60 49.83.584.0848.63.484.0947.93.484.04

70 47.83.893.6146.83.783.6346.13.733.63

80 47.64.333.2246.64.193.2645.94.073.30

60 41.33.413.5641.03.353.5940.23.333.54

70 39.83.683.1739.53.623.2039.13.603.19

80 39.54.082.8439.34.012.8838.93.932.90

60 37.93.273.4037.23.233.3737.13.223.38

70 36.03.562.9735.63.512.9735.63.492.99

80 35.23.912.6434.93.852.6635.13.822.69

60 31.63.073.0231.63.053.0431.63.053.04

70 30.33.382.6329.93.332.6330.23.332.66

80 29.63.672.3728.83.602.3529.53.592.41

60 23.22.812.4223.52.822.4423.72.832.46

70 22.23.012.1622.63.012.2022.83.022.21

80 21.13.231.9221.73.221.9821.93.231.98

60 19.22.592.1719.42.612.1819.72.652.18

70 18.22.761.9318.72.781.9718.92.811.97

80 16.82.891.7117.62.921.7717.72.941.77

MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.

1400 1500 1600

036-21030-003 Rev. B (0203)

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

F2FP048 1.02 0.99 1.03

G2FD042(S,H)21 0.99 0.98 1.01

G2FD046(S,H)17 0.99 0.96 1.03

G2FD048(S,H)21, 1.00 0.94 1.06

G1HD048 1.00 0.96 1.04

G1HD060 1.00 0.95 1.05

G1UA048S21 1.00 0.94 1.06

G1FA048S21 1.00 0.94 1.06

T.C. S.C. KW

Unitary Products Group 21

Page 22

036-21030-003 Rev. B (0203)

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E4FD048S06, E4FD048S25, 46

EVAPORATOR COIL MODEL NO F2FP048

AIR TEMP. ENTERING OUTDOOR

UNIT

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

AIR TEMP. ENTERING

INDOOR

COIL

60 55.4 3.90 4.17 57.6 4.02 4.20 56.7 3.83 4.34

70 55.3 4.47 3.63 55.2 4.34 3.73 54.8 3.90 4.13

80 55.2 5.24 3.09 52.8 4.68 3.31 52.7 4.20 3.68

60 47.0 4.25 3.24 47.1 3.70 3.73 48.9 3.74 3.83

70 46.9 4.27 3.23 47.0 4.18 3.30 47.2 3.80 3.64

80 46.3 4.89 2.77 46.9 4.80 2.87 45.4 4.10 3.25

60 37.3 3.27 3.35 42.6 3.99 3.13 43.0 3.64 3.47

70 37.0 3.68 2.94 42.6 4.07 3.07 42.2 3.82 3.24

80 36.2 5.36 1.98 42.1 4.62 2.67 39.7 5.06 2.30

60 35.8 3.69 2.85 36.8 3.72 2.90 37.7 3.57 3.10

70 34.8 3.83 2.66 36.2 3.89 2.73 36.4 3.62 2.95

80 33.5 4.24 2.32 35.5 4.33 2.40 35.0 3.90 2.63

60 28.7 3.30 2.55 29.2 3.30 2.59 29.4 3.05 2.83

70 27.5 3.57 2.25 28.0 3.57 2.30 28.4 3.29 2.53

80 26.2 3.87 1.99 26.8 3.86 2.04 27.3 3.55 2.26

60 24.6 3.04 2.38 25.0 3.04 2.41 25.4 2.81 2.66

70 23.2 3.34 2.03 23.6 3.34 2.07 23.9 3.08 2.28

80 21.8 3.54 1.81 22.2 3.53 1.85 22.6 3.26 2.03

MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.

1450 1600 1750

ID CFM

Multipliers for determining the performance with other indoor sections.

Coil

G2FD048(S,H)21,2 1.00 0.94 1.06

G2FD060(S,H)24 1.00 0.95 1.05

G1HD048 1.00 0.95 1.05

G1HD060 1.00 0.95 1.05

G1UA060S24 1.00 0.95 1.05

G1FA048S21 1.00 0.96 1.04

G1FA060S24 1.00 0.95 1.05

G1UA048S21 1.00 0.96 1.04

T.C. S.C. KW

22 Unitary Products Group

Page 23

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E4FD060S06, E4FD060S25, 46

EVAPORATOR COIL MODEL NO F2FP060

AIR TEMP. ENTERING OUTDOOR

UNIT

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR

COIL

60 70.05.583.7368.15.393.7566.15.233.75

70 71.75.823.6670.35.613.7268.75.443.75

80 71.66.793.1370.76.513.2369.76.313.28

60 60.3 5.33 3.32 59.9 5.19 3.38 57.7 5.11 3.31

70 60.85.563.2161.05.423.3059.35.343.26

80 60.36.352.7861.06.182.8959.76.082.88

60 55.44.983.2456.05.013.2753.84.953.17

70 56.05.373.0456.05.323.0755.55.293.06

80 55.76.002.7155.15.862.7556.45.842.82

60 49.74.833.0050.14.783.0549.84.733.07

70 48.45.242.6948.95.182.7549.05.142.77

80 46.65.552.4447.25.472.5147.65.452.54

60 39.74.712.4740.94.762.5238.74.752.39

70 38.54.982.2739.74.992.3337.74.992.22

80 37.35.352.0438.45.312.1236.85.312.03

60 35.14.652.2436.54.672.3236.84.652.35

70 33.54.882.0434.74.892.1035.14.892.13

80 32.15.061.8833.15.071.9433.65.081.97

MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.

1750 1800 1850

036-21030-003 Rev. B (0203)

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

F2FV060 0.98 0.98 1.00

GFD060(S,H)24 0.98 0.95 1.03

G1HD060 0.98 1.05 0.94

G1UA060S21,24 1.01 0.98 1.03

G1FA060S21,24 1.01 0.98 1.03

T.C. S.C. KW

Unitary Products Group 23

Page 24

MATCHING INDOOR COMPONENTS

ADD-ON COILS - FOR FURNACE APPLICATIONS

G1UA 1/2 CASED UPFLOW

G1FA FULL CASED UPFLOW

* Available with factory installed horizontal drain pan.

G1HD HORIZONTAL DUCT

AIR HANDLERS - FOR NON-FURNACE APPLICATIONS

N1AH OR N1VS MODULAR BLOWER (UPFLOW, HORIZONTAL AND DOWNFLOW)

G1NA UNCASED UPFLOW

G2FD* MULTI-POSITION (UPFLOW, HORIZONTAL AND DOWNFLOW)

Unitary 5005 Norman Product York OK Group Drive 73069

G2FD COIL

F2RC / F2FC OR F2RC / F2FP FAN COIL UNITS (UPFLOW, HORIZONTAL)

York E4FD018, E4FD024, E4FD036, E4FD030, E4FD042 Technical Manual

Specifications and Main Features

Frequently Asked Questions

User Manual