YOKOGAWA XL100, XL112, XL111, XL114, XL121 User Manual

...

Download

User's Manual

XL100 Datum-Y

クイックマニュアル QuickSetupManual

IMXL120P

1stEdition:Apr.2007(YMI)

XL111,XL112,XL114 ポータブルデータロガ−(Datum-Y) XL121,XL122,XL124 ポータブルデータステーション(Datum-Y)

XL111,XL112,XL114 PortableDataLogger(Datum-Y) XL121,XL122,XL124 PortableDataStation(Datum-Y)

IM XL120P

Introduction

Thank you for purchasing our XL100 Portable Data Station/Portable Data

Logger.

This Quick Setup Manual briefly describes the key operations as well as setting

examples of the XL100 upon actual measurement, so that you can operate the

XL100 for the first time.

In addition to this manual, the User’s Manual and Communication Function

Manual contained in the CD-ROM are available separately. The User’s Manual

provides detailed information regarding all of the functions and operations of the

XL100 excluding the communication functions. The Communication Function

Manual provides information necessary for using communication functions and

creating communication programs. Use them together with this Quick Setup

Manual. The Communication Function Manual is available only for the Portable

Data Station.

After reading this manual, keep it in an easily accessible place for later

reference. This manual will come in handy when you are unsure of how to

operate the product.

Notes

• The contents of this manual are subject to change without prior notice.

• Figures and illustrations representing display views in this manual may differ

from actual views.

• Every effort has been made to ensure accuracy in the preparation of this

manual. However, should any doubts arise or errors come to your attention,

please contact the vendor from which you purchased the product.

• The contents of this manual may not be transcribed or reproduced, in part or

in their entirety, without prior permission.

Trademarks

The company and product names referred to in this document are either

trademarks or registered trademarks of their respective holders.

Revisions

First Edition: April, 2007

1st Edition: April 2007 (YMI)

IM XL120P

Safety Precautions

When operating the instrument, be sure to observe the cautionary notes given

in “Safety Precautions” on pages 4 and 5 and section 3.1, “Handling

Precautions” in the User’s Manual. If you use the instrument in any way other

than as instructed, the instrument’s protective measures may be impaired.

The following safety symbols are used on the instrument and in this manual.

WARNING

Indicates a hazard that may result in the loss of life or serious injury of the user unless the described instruction is abided by.

CAUTION

Indicates a hazard that may result in an injury to the user and/or physical damage to the product or other equipment unless the described instruction is abided by.

Note

Indicates information that is essential for handling the instrument or should be noted in order to familiarize yourself with the instrument’s operating procedures and/or functions.

TIP

Indicates information that complements the present topic.

IM XL120P

Contents

Introduction ............................................................................. 1

Safety Precautions.................................................................. 2

1. Checking the Contents of the Package ........................ 4

2. Flow of Operation ........................................................... 5

3. Names and Functions of Parts ...................................... 6

4. How to View the Display ................................................. 9

5. Introduction of the Main Functions............................. 15

Input Type and Calculation .................................................................. 15

Alarm Function ..................................................................................... 16

Saving Data ........................................................................................... 17

Triggers ................................................................................................. 18

File Operations ..................................................................................... 18

Communication Function .................................................................... 19

6. Operation Mode and Basic Key Operations ............... 21

Operation Modes and Switching the Operation Mode ...................... 21

Switching the Display in Free Running Mode or Logging Mode...... 22

Switching the menu in Setting Mode .................................................. 22

Key Operations for Entering Characters ............................................ 23

Key Operations for Entering Values .................................................... 23

7. Signal Wiring ................................................................. 24

8. Connecting to the Power Supply and Turning the

Power Switch ON/OFF .................................................. 26

Connecting the Power Supply ............................................................. 26

Turning the Power Switch ON/OFF ..................................................... 27

9. Setting the Input Channel ............................................ 29

10. Setting the Data Save Operation ................................. 33

11. Confirming the Settings and Performing the Measure-

ment ............................................................................... 38

12. Inserting an External Storage Medium and Saving Data . 39

Inserting an External Storage Medium ............................................... 39

Starting the Data Save Operation ....................................................... 40

Stopping the Data Save Operation ..................................................... 40

13. Analyzing the Saved Data ............................................ 41

Loading the Saved Data File ................................................................ 41

Loading the Measured Data ................................................................. 43

Displaying Statistical Calculation Values ........................................... 43

14. Troubleshooting ............................................................ 44

Index....................................................................................... 45

IM XL120P

1. Checking the Contents of the Package

Unpack the box and check the contents before operating the instrument. Should

the product you have received be the wrong model, lack any items, or show any

problems in its appearance, contact the vendor from whom you purchased the

product.

Instrument Main Unit

Check the model and suffix code printed on the nameplate on the rear panel to

ensure that the XL100 is exactly as specified in your purchase order.

XL100

No.

Model

When inquiring about the product to the vender, please also give the vendor this number.

Accessories

Make sure that the package contains all the accessories listed below and that

they are all free from any damage.

These are attached to the XL100.

Terminal block unit

Rubber boot

AC adapter

Quick setup manual (this manual)

CD-ROM

Contains Standard Software and PDF manuals (User's Manual, Quick Setup Manual, and Communication Function Manual).

c h

(Ex.: 95052)

Screwdriver for terminals

Side cover (Supplied with the XL121, XL122, and XL124)

TIP

For details on peripherals and spare parts, see page 3 in the User’s Manual.

IM XL120P

2. Flow of Operation

Connect the wires

Connect the power supply and turn the power ON

Configure

• Set the input

• Save the data

Set other items (as necessary)

• Alarm

• Display

• Calculation

• Communications

• Hardware

• System

Confirm the settings and measure

Save the data

Free Running Mode

Logging Mode

Set the language

Initial startup only

Analyze the data

• Review Mode

• Logging & Review Mode

Process the file (as necessary)

• Rename the file

• Delete the files

• Copy the data

Reference chapter/ section in the User’s Manual

3.3-3.5

Page 24

Page 26

Page 28

Page 29

Page 33

Page 38

Page 39

Page 41

Reference page in this manual

3.6, 4.1

Chapter 5

9.1

Chapter 6 Chapter 7 Chapter 8 Chapter 10 Chapter 4, 11, etc.

11.6, 11.7

9.1

9.2

9.7

9.8

9.9

IM XL120P

3. Names and Functions of Parts

Front Panel

HOME REVIEW FILE

SETTING

HOLD

TIME / DIV

SAVE

RANGE

DISPLAY

GROUP

MARK

SET

ESC

SELECT

START / STOP

Display

Displays measured data, operation status, setup menu, settings, etc.

Terminal block unit

Terminal block unit where probes are connected.

Keys

Operation status LED

POWER : Illuminates when the power is ON CHARGE : Illuminates when the battery is being charged START : Illuminates while logging

Status display section

Data display, setting menu, and setting display section

For the wiring procedure, see page 23.

For the viewing the displays, see page 9.

Keys

HOME REVIEW FILE

SETTING

HOLD

TIME / DIV

SAVE

RANGE

DISPLAY

GROUP

MARK

SET

ESC

SELECT

START / STOP

IM XL120P

1. HOME Key

Press this key to enable Free Running Mode for measuring instantaneous values (see page 21).

2. REVIEW Key

Press this key to enable Logging & Review Mode in which past measured data can be viewed while logging (see page 21) or enable Review Mode in which saved data can be analyzed (see page 21).

3. FILE Key

Press this key to enable File Operation Mode in which file names can be changed, measured data can be copied, setting data can be saved or loaded, and so on (see page 21).

4. SETTING Key

Press this key to set measurement conditions, conditions for saving measured data, alarm conditions, etc.

5. HOLD Key

Press this key to hold the display so that the measured values are not updated or to release the display. In addition, hold this key down to enable or disable key lock.

6. TIME/DIV Key

Press this key to switch the time axis (the time per grid (division)).

7. ESC Key

Press this key to cancel a key operation.

8. SET Key

Press this key to set settings entered through the keys.

9. START/STOP Key

Press this key to start/stop logging.

10. RANGE Key

Press this key to change the input range or span (scale).

11. DISPLAY Key

Press this key to switch the display in Free Running Mode or Logging Mode (see page

22). Press this key also to switch between marker display and statistical calculation display in Review Mode.

12. SAVE Key

Press this key to manually save or print the measured data or screen data.

13. GROUP Key

Press this key to switch the displayed group of measurement, calculation, and communication input channels.

14. Fast Forward Key

Press this key to move the marker to the left or right by 1 division on the review display (see page 43).

15. MARK Key

Press this key to select a marker to be activated on the review display (see page 43).

16. Arrow/SELECT Key

Press the arrow keys to select items on the display. Press this key also to move the marker to the left or right on the review display (see page 43). Press the SELECT key to confirm a selection.

3. Names and Functions of Parts

IM XL120P

Side Panel

For details on connecting the power supply and turning the power ON/OFF, see pages 26 and 27.

For details on how to insert the CF card or SD card, see page 39.

CF card slot

SD card slot*

Trigger input/output terminal

RS-485 connector*

Ethernet port*

Power switch

AC adapter jack

RS-232 connector*

For a description, see section 3.9.

For a description, see section 3.8.

For a description, see section 4.7.

For a description, see section 3.5.

For a description, see section 3.4.

For a description, see section 3.8.

For a description, see section 4.1.

For a description, see section 3.6.

Digital I/O connector

USB port for USB memory

USB port for connecting a PC*

* Supported only on the XL121, XL122, and XL124

USB

RS485 RS232LAN

TRIGGER

ALARM

LOGIC/PULSE

GND

OUT

DC INPUT

POWER

12V

20W MAX

The reference sections are those of the User’s Manual.

Rear Panel

Screwdriver for terminals (accessory)

Press the screwdriver towards the spring (right in this figure) to detach it.

Battery cover

Holds the lithium ion battery (94009) sold separately .

Name plate

3. Names and Functions of Parts

IM XL120P

4. How to View the Display

Status Display Section

1. Operation Mode

Displays the mode: Free Running, Logging, Logging & Review, Setup, or

File Operation.

2. User name

Displays the login user name when the key login function (see section 11.7

in the User’s Manual) is turned ON.

3. Group Name (For the procedure to set groups, see section 7.2 in the

User’s Manual)

Displays the group name of the displayed measurement channel.

4. Alarm Status (For a description of the alarm function, see page 16)

The status is displayed using different icon colors as follows:

Gray: No alarm setting Yellow-green: Alarm setting enabled Red: Alarm activated

5. Alarm Output Status

The status is displayed using different icon colors for each alarm output

channel (1 to 4) as follows:

Gray: No alarm setting Yellow-green: Alarm setting enabled Red: Alarm outputting

6. Date/Time (For the procedure to set the date/time, see section 4.3 in the

User’s Manual)

Displays the year, month, day, hour, minute, and second.

7. Sampling Interval

Displays the sampling interval (measurement/save interval of measured

data) when in Free Running, Logging, or Logging & Review Mode.

8. Various Icons

The following icons are used to display the operation status, interface usage

status, etc.

An icon shown when the data save destination is set to internal memory. The icon blinks when there is access to the internal memory. The icon is gray when the data save destination is not set to internal memory.

IM XL120P

An icon shown when the data save destination is set to internal memory and the save mode is set to DIVISION. The icon blinks when there is access to the internal memory.

An icon shown when the data save destination is set to internal memory and the memory full operation is set to REPEAT. The icon blinks when there is access to the internal memory.

An icon shown when the data save destination is set to internal memory and the memory full operation is set to DELETE. The icon blinks when there is access to the internal memory.

An icon shown when the data save destination is set to internal memory, the save mode is set to DIVISION, and the memory full operation is set to REPEAT. The icon blinks when there is access to the internal memory.

An icon shown when the data save destination is set to internal memory, the save mode is set to DIVISION, and the memory full operation is set to DELETE. The icon blinks when there is access to the internal memory.

An icon shown when the data save destination is set to CF card. The icon blinks when there is access to the CF card. The icon is gray when the data save destination is not set to CF card.

An icon shown when the data save destination is set to CF card and the save mode is set to DIVISION. The icon blinks when there is access to the CF card.

An icon shown when the data save destination is set to CF card and the memory full operation is set to REPEAT. The icon blinks when there is access to the CF card.

An icon shown when the data save destination is set to CF card and the memory full operation is set to DELETE. The icon blinks when there is access to the CF card.

An icon shown when the data save destination is set to CF card, the save mode is set to DIVISION, and the memory full operation is set to REPEAT. The icon blinks when there is access to the CF card.

An icon shown when the data save destination is set to CF card, the save mode is set to DIVISION, and the memory full operation is set to DELETE. The icon blinks when there is access to the CF card.

An icon shown when the data save destination is set to SD card. The icon blinks when there is access to the SD card. The icon is gray when the data save destination is not set to SD card. (Supported only on the XL121, XL122, and XL124.)

An icon shown when the data save destination is set to SD card and the save mode is set to DIVISION. The icon blinks when there is access to the SD card. (Supported only on the XL121, XL122, and XL124.)

An icon shown when the data save destination is set to SD card and the memory full operation is set to REPEAT. The icon blinks when there is access to the SD card. (Supported only on the XL121, XL122, and XL124.)

4. How to View the Display

IM XL120P

An icon shown when the data save destination is set to SD card and the memory full operation is set to DELETE. The icon blinks when there is access to the SD card. (Supported only on the XL121, XL122, and XL124.)

An icon shown when the data save destination is set to SD card, the save mode is set to DIVISION, and the memory full operation is set to REPEAT. The icon blinks when there is access to the SD card. (Supported only on the XL121, XL122, and XL124.)

An icon shown when the data save destination is set to SD card, the save mode is set to DIVISION, and the memory full operation is set to DELETE. The icon blinks when there is access to the SD card. (Supported only on the XL121, XL122, and XL124.)

An icon shown when there is data saved in the backup memory. The icon blinks when there is access to the backup memory. The icon is gray when there is no data saved to the backup memory.

An icon shown when the interface is set to LAN, LAN/RS-232, or LAN/RS-485. For other cases, the icon is gray. (Supported only on the XL121, XL122, and XL124.)

An icon shown when the interface is set to USB. For other cases, the icon is gray. (Supported only on the XL121, XL122, and XL124.)

An icon shown when the communication protocol is set to Modbus (slave). The icon is gray when set to Modbus (master). (Supported only on the XL121, XL122, and XL124.)

An icon shown when the communication protocol is set to Modbus (master). The icon is gray when set to Modbus (slave). (Supported only on the XL121, XL122, and XL124.)

An icon shown when the printer output is turned ON and the sampling interval is greater than or equal to 1 minute. The icon is gray when the printer output is OFF. (Supported only on the XL121, XL122, and XL124.)

An icon shown when the printer output is turned ON and the sampling interval is less than or equal to 30 seconds. This indicates that only manual print is valid using the SAVE key. (Supported only on the XL121, XL122, and XL124.)

An icon shown when the display update is held. The icon is gray when the display is not held.

An icon shown when key lock is enabled. The icon is gray when key lock is disabled.

An icon shown when the AC adapter is connected.

An icon shown when the AC adapter is not connected, and the XL100 is

running on a battery. Shows the remaining battery power using four levels

(

→ → → ).

4. How to View the Display

IM XL120P

Data Display Section

Waveform & Digital Display

1. Waveform

Waveforms of measured data, calculated data, and communication input data. Waveforms of logic input are shown at the lower section of the screen as shown in the figure above.

2. Time Axis

Displays the time axis (time per grid (division)) specified by the TIME/DIV key.

3. Alarm Line

Displayed with a dotted line at the position of the alarm value of the selected channel (active channel).

4. Scale Upper Limit

Shows the display upper limit of the active channel.

5. Scale Lower Limit

Shows the display lower limit of the active channel.

6. Pen

Displayed at the current value position of each channel. The active channel is shown highlighted in reverse video.

7. Usage Indication Bar of the Storage Media

Displays using a blue bar the amount of space used with respect to the total space on the storage medium that is specified to be the save destination of the measured data.

Total space on the save destination medium

Used space

Free space

8. Grid

The grid can be turned ON/OFF.

4. How to View the Display

IM XL120P

9. Elapsed Time

Displays the elapsed time from the start of the logging operation.

10. Digital Display

Displays the current values of the measured data, calculated data, and

communication input data using numeric values.When an alarm is occurring, the

value is shown in red in reverse video.

11. Unit

Displays preset characters such as °C or an arbitrary specified characters (up to 6

characters).

12. Channel No./Tag

Displays the channel number and the specified tag (up to 8 characters). The

active channel is shown highlighted (reverse video).

Other Data Displays

In addition to the waveform & digital display, other displays are available including the

waveform display that does not show numeric values. For a description of the data

displays below, see section 2.3, “Data Display” in the User’s Manual.

• Digital Display

Displays the numeric values of the instantaneous values and statistical

calculation values.

• Bar Graph Display

Displays a bar graph in place of a waveform.

4. How to View the Display

IM XL120P

• Review Display

Displays the waveforms of data saved in the past.

• Logging & Review Display

Displays both the waveforms of data currently being logged and the

waveforms of data saved in the past.

• Alarm Summary Display

Displays the alarm status in a list.

• Log Display

Displays the log data of error messages and communications.

4. How to View the Display

IM XL120P

5. Introduction of the Main Functions

Input Type and Calculation

As shown in the table below, the available input types are analog input, which includes DC voltage, thermocouple, and RTD, and other inputs, which consist of pulse signal (1 channel) and logic signals (2 channels). In addition, the arithmetic calculations between two inputs can be performed and assigned to a calculation channel and displayed in the same fashion as measured values. The statistics of measured values can also be displayed. For details on the input settings, see chapter 5, “Setting the Input Channels.” For details on calculation, see chapter 8, “Setting the Calculation of Measured Data.”

Input/Calculation Description

DC voltage Measures a DC voltage in the range of ±100 mV to ±50 V.

Thermocouple Selectable from the following types: R, S, B, K, E, J, T, N, W,

L, and U.

RTD Selectable from Pt100 and JPt100 types.

Pulse signal Displays the pulse input as number of revolutions, integrated

value, or instantaneous value.

Logic signal Displays the logic waveform at the lower section of the display by

taking input voltage less than or equal to 0.9 V to be OFF (0) and input voltage greater than or equal to 2.1 V to be ON (1).

Calculation Performs arithmetic calculations using measured data,

calculated data, communication data, and arbitrary assigned constants and displays the result.

Statistical calculation Calculates and displays the maximum, minimum, average,

peak (P-P), or rms value of the measured value.

Voltage

Thermocouple

RTD

Signal input

Displays the measured/calculated data

Pulse/Logic input

TIP

You must connect a digital I/O cable sold separately to the input terminal (digital I/O connector) to apply pulse or logic signals. (See section 3.4 in the User's Manual.)

IM XL120P

Alarm Function

Generates an alarm when the measured/calculated value meets a certain

condition. When an alarm occurs, information notifying the alarm occurrence is

displayed on the screen. In addition, an alarm signal can be delivered from the

output terminal (digital I/O connector) on the rear panel of the XL100 by

connecting a digital I/O cable (option). You can select the alarm conditions from

the following table.

For details on the settings, see chapter 6, “Setting Alarms” in the User’s

Manual.

Input Type Setting Alarm Condition

Level OFF Not set alarm conditions. or Pulse Hi An alarm occurs when the measured/calculated

value is greater than or equal to the alarm value.

Lo An alarm occurs when the measured/calculated

value is less than or equal to the alarm value.

Window IN An alarm occurs when the measured/calculated

value is within the lower limits and upper limits of the alarm range.

Window OUT An alarm occurs when the measured/calculated

value is outside the lower limits and upper limits of the alarm range.

Logic OFF Not set alarm conditions.

Hi An alarm occurs when the logic input changes

from low to high.

Lo An alarm occurs when the logic input changes

from high to low.

Alarm value

Alarm release

Measured value

Alarm occurrence

Measured value

Alarm value

Alarm occurrence

Alarm value

Alarm release

Measured value

Alarm occurrence

Window IN

Window OUT

Measured value

Alarm release

Alarm value

Alarm occurrence

Alarm release

5. Introduction of the Main Functions

IM XL120P

Saving Data

Measured data, calculated data, setting data, and so forth can be saved to the XL100 internal memory or an external storage medium (CF card or SD card) that is inserted in the XL100.

Save the data

Supported only on the XL121, XL122, and XL124

TIP

The XL100 is equipped with a USB port for USB memories. However, data cannot be saved directly to a USB memory (see section 3.9 in the User’s Manual).

The types of data that can be saved are as follows:

Type Description

Logging data The instantaneous values of the measured/calculated data

can be saved at a specified sampling interval. The data save operation is started or stopped with the START/STOP key. The save operation can also be started or stopped when a specific event (see “Trigger” on the next page) occurs. The logging data contains alarm information.

Manual sampled data The measured/calculated data (instantaneous values) of all

channels can be saved by pressing the SAVE key in Free Running Mode.

Alarm data The same information as the alarm summary display can be

saved by pressing the SAVE key during alarm summary display.

Screen image data The image data of the screen being displayed can be saved

by pressing the SAVE key in Free Running Mode, etc.

Setting data The setting data of the XL100 can be saved in File Operation

Mode.

Log data The same information as the log display can be saved by

pressing the SAVE key during log data display.

Backup file If the data save operation is not carried out normally to the

internal memory or external storage medium (CF card or SD card), the data is saved to the backup memory of the XL100. The saved data can be copied to an external storage medium.

5. Introduction of the Main Functions

IM XL120P

Triggers

In addition to using the START/STOP key to start or stop the logging, a trigger for starting (or stopping) the save operation of the logging data (measured/ calculated data) can be configured for automatic operation. The trigger for logging can be selected from the list below and configured.

Type Description

None Not set trigger conditions.

External A trigger is activated when a signal is applied to

the external trigger input terminal.

Level High limit (H) A trigger is activated when the measured value is greater

than or equal to the specified value.

Low limit (L) A trigger is activated when the measured value is less than

or equal to the specified value.

Window IN A trigger is activated when the measured value is within the

specified lower and high limits.

Window OUT A trigger is activated when the measured value is outside

the specified lower and high limits.

Alarm A trigger is activated when an alarm occurs on the specified

alarm output channel.

Time A trigger is activated at the specified time.

Timer The time at which the data save operation is stopped can

be specified. Logging is stopped after the specified time elapses.

File Operations

The following file operations are available.

Operation Type Description

Rename Renames files saved on an external storage medium (CF card

or SD card) or internal memory.

Save setting data Saves setting data to an external storage medium (CF card, SD

card, and USB memory), internal memory, or setting memory.

Load setting data Loads the setting data saved on an external storage medium

(CF card, SD card, and USB memory), internal memory, or setting memory and changes the settings.

Copy data Copies the files saved to the an external storage medium (CF

card or SD card), internal memory, or setting memory to an external storage medium (CF card, SD card, or USB memory), internal memory, or setting memory.

Copy backup memory Copies the files saved to the backup memory (memory to which

data is saved when data cannot be saved to an external storage medium or internal memory) to an external storage medium (CF card or SD card) or internal memory.

Format Formats an external storage medium (CF card or SD card),

backup memory, or internal memory.

5. Introduction of the Main Functions

IM XL120P

Communication Function (Supported only on the XL121, XL122, and XL124)

FTP Client/Server

The Ethernet interface can be used to automatically transfer measurement data

files to an FTP server connected to the network or access the XL100 from a PC

through FTP to retrieve data on the external storage medium or internal

memory of the XL100.

Ethernet

FTP server

Hub

Automatically save measured data

Load measured data

FTP client

Ethernet

Hub

FTP server

Web Server

By configuring the XL100 to be a Web server, the XL100 screen can be shown

on the PC. You can monitor the measured data and switch the display from the

PC.

Ethernet

Hub

Monitor the measured data

Web server

Monitor the measured data

5. Introduction of the Main Functions

IM XL120P

E-mail transmission

An e-mail can be sent automatically from the XL100 when an alarm occurs.

Ethernet

Hub

Send e-mail

Receive e-mail

Serial Communication

The USB interface or serial interface can be used to change the XL100 settings from a PC or retrieve data into the PC through command communication. In addition, Modbus communication is possible on the serial interface. The Modbus master function enables the measured data of a measuring instrument connected as a Modbus slave to be retrieved as communication input data. The data can be assigned to a communication channel and displayed on the XL100 in a similar fashion to measurement and calculation channels.

Change settings and load data

USB, RS-232, RS-485

Command communication

RS-232, RS-485

Modbus communication

Modbus master

Measurement instrument

Modbus slave

For details on the communication functions, see the Communication Function Manual (contained in the CD-ROM).

5. Introduction of the Main Functions

IM XL120P

6. Operation Mode and Basic Key Operations

Operation Modes and Switching the Operation Mode

As shown in the figure below, the XL100 has six operation modes: (1) Free

Running Mode in which instantaneous values are measured, (2) Logging Mode

in which continuous measurement is performed while saving data, (3) Logging

& Review Mode in which past measured data can be viewed while the logging

operation is in progress, (4) Review Mode in which saved data is analyzed, (5)

File Operation Mode in which file operations such as saving and loading of the

setup data is performed, and (6) Setting Mode in which various settings such as

the measurement conditions are specified. The keys in the figure below are

used to switch between these modes.

HOME

REVIEW

FILE

SETTING

START / STOP

Review Mode

Setting Mode

Free Running Mode

File Operation Mode

Logging Mode

Logging & Review Mode

Switch the display

Wavef orm

Digital

Bar graph

Alarm summary

Log

Switch the display

Wavef orm

Digital

Bar graph

Alarm summary

Log

Setting menu

Select

Input

Display

Alarm

Calculation

Hardware

Marker measurement

Set

File operation

Select

Rename files

Delete files

Setup file Copy data files

Copy backup memory

Format

Set

REVIEW

Statistical

calculation

System information

System

information

Data Save

Communication

System

Initialize log

Marker

measurement

Statistical calculation

IM XL120P

Switching the Display in Free Running Mode or Logging Mode

To switch to a display other than waveform & digital display, press DISPLAY to

show the display switch pop-up menu, select the display using the arrow keys,

and press SELECT.

DISPLAY

SELECT

Display the menu

Select the display

Confirm the display

Switching the menu in Setting Mode

Press the arrow keys to select the desired item, and press SELECT. A

selection list, a setting window, or a setting menu that is one level lower is

displayed. To return to the original setting menu, press ESC.

SELECT

Select the setup item

Confirm the setup item

ESC

6. Operation Mode and Basic Key Operations

IM XL120P

Key Operations for Entering Characters

For settings that require characters to be entered, a character entry window

opens as shown below.

To enter a character, press the arrow keys to move the cursor in the character

selection area, select the character, and press SELECT. To set the entered

value, press SET.

Character entry area

Character selection area

Character type selection area

(A: alphabet characters. 0: numeric characters and symbols)

Backspace

Delete

Key Operations for Entering Values

For settings that require a value to be entered, a value entry window opens as

shown below. Press the up and down arrow keys to increment or decrement

the value and the left and right arrow keys to move along the digits. To set the

entered value, press SET. The window will not close when you press SET if a

value outside the range is entered. Enter a value within the range.

6. Operation Mode and Basic Key Operations

IM XL120P

7. Signal Wiring

Signal Input Wiring (for Clamp Screws)

Be sure to also read the precautions in section 3.3, “Wiring the Input Signal

Cable” in the User’s Manual when wiring cables.

CAUTION

Do not apply an input exceeding the following values. Otherwise, the XL100 may break down.

• Maximum input voltage

100 mV, 500 mV, and 1 V range and TC input: ±10 VDC

5 V, 10 V, 50 V, and 1-5V/f.s. range: ±60 VDC

• Maximum common mode noise voltage

30 VACrms (50/60 Hz) or ±60 VDC

Wiring Procedure

1. Open the terminal cover of the terminal block unit.

2. Wire the input signal cables to the input terminals.

As shown below, loosen the terminal screws using the screwdriver provided,

insert the signal wires, and fasten the terminal screws.

3. Close the terminal cover of the terminal block unit.

Enlarged view

Accessory screwdriver for terminals

Signal wire

Terminal cover

Terminal block unit

TIP

The terminal block unit can be removed. For the procedure to remove the terminal block unit, see section 3.3, “Wiring the Input Signal Cable” in the User’s Manual.

IM XL120P

Wiring Diagram

Use wires of the following specifications.

TC input

DC voltage input

RTD input

–

Lead wire resistance per wire

of 10 Ω or less. Make the

resistance of the three wires equal.

Extension leadwire

DC voltage input

–

DC current input

Shunt resistor

Example: For 4 to 20 mA input, use a shunt

resistor of 250 Ω ± 0.1%.

–

Note

• For clamp terminals, use wires of the following specifications.

• Conductive cross-sectional area for single wire: 0.14 mm2 to 2.5 mm2, stranded wire: 0.14 mm2 to 1.5 mm

AWG: 26 to 14

• Length of the stripped section of the wire: Approx. 7 mm

Input signal wires whose diameter is 0.3 mm or less may not be securely fastened. Fold over the conducting section of the wire, for example, to make sure that the wire is securely fastened to the clamped terminal.

•RTD input terminals A (+) and B (–) are isolated on each channel. Terminal b is shorted internally across all channels.

Other Wiring

• For a description of the pulse input, logic input, and alarm output wiring, see

section 3.4, “Wiring the Pulse Input, Logic Input, and Signal Cables” in the

User’s Manual.

• For a description of the external trigger input/output wiring, see section 3.5,

“Wiring the External Trigger I/O Signal Cables” in the User’s Manual.

7. Signal Wiring

IM XL120P

8. Connecting to the Power Supply and Turning the Power Switch ON/OFF

Connecting the Power Supply

Be sure to also read the precautions in section 3.6, “Connecting the Power

Supply” in the User’s Manual when connecting the power supply.

WARNING

• Use only the power cord and AC adapter supplied by YOKOGAWA Meters & Instruments for the XL100.

• Check that the power source voltage matches the supply voltage rating (100 to 240 VAC), and then connect the power cord.

Connecting the AC Adapter

Follow the steps below to connect the AC adapter.

1. Check that the power switch is OFF.

2. Connect the AC adapter to the AC adapter jack of the XL100.

3. Connect the plug of the power cord supplied with the AC adapter to the

power connector of the AC adapter.

4. Connect the other end of the power cord to the power outlet that meets the

power rating (requirements).

Power supply rating of the AC adapter

Supply voltage rating 100 to 240VAC

Allowable supply voltage range 90 to 264 VAC

Power supply frequency rating 50/60 Hz

2. Connect.

3. Connect.

4. Connect.

1. Check that the power is OFF.

AC adapter

AC adapter jack

Power cord

IM XL120P

Turning the Power Switch ON/OFF

The power switch is located on the right side panel of the XL100. To turn the power ON, press the I (ON) side of the power switch. Press the O on the other side to turn the power OFF.

Power switch

Power Switch Operation When the Side Cover Is Attached

(Supported only on the XL121, XL122, and XL124)

You can operate the power switch with the rubber boot and side cover attached by opening the power switch cover. When attaching the accessory side cover, fasten the side cover attachment screw to fix the cover to the XL100.

Side cover

Power switch cover

Side cover attachment screw

Rubber boot

Open from this end.

Display at Power ON

When the power is turned ON, the XL100 shows the startup screen followed by the self-test screen. When the self-test completes normally, the XL100 shows “Self Test OK” followed by the Waveform & Digital display of Free Running Mode. For the corrective action when an error message is displayed, see section 4.1, “Turning ON/OFF the Power Switch” in the User’s Manual.

8. Connecting to the Power Supply and Turning the Power Switch ON/OFF

IM XL120P

Language Setting at Startup

When you start up the XL100 for the first time (the first time you turn on the

XL100 after purchase), you must set the language that you are going to use.

Follow the procedure below to set the language.

Once you set the language, the XL100 will start up using the specified language

the next time.

1. When you turn the power switch ON, the following screen appears.

2. Use the arrow keys to select the language, and press SELECT.

3. The language is set, and a self-test starts automatically.

TIP

To change the language once you set it, press SETTING, select HARDWARE > LANGUAGE, and change the setting.

8. Connecting to the Power Supply and Turning the Power Switch ON/OFF

IM XL120P

9. Setting the Input Channel

This chapter explains the steps to set the input channel using an example in which a

thermocouple (type E, measurement range: 0.0 to 1000.0°C) is input to CH1. The

settings of other input channels are not changed from the default settings.

For details on setting the input channels, see chapter 5, “Setting the Input

Channels” in the User’s Manual.

Keys

Display

Move the cursor to CH01.

SELECT

SETTING

Change to Setting Mode.

Show the INPUT menu.

SELECT

Show the ANALOG INPUT setting screen.

IM XL120P

SELECT

Keys

Display

SELECT

Show the CH01 setting screen.

Show the MODE selection list.

Move the cursor to TC.

SELECT

Select TC.

Move the cursor to MODE.

9. Setting the Input Channel

IM XL120P

SELECT

Keys

Display

10.

11.

12.

Move the cursor to RANGE.

Show the RANGE selection list.

Move the cursor to E.

13.

SELECT

Select E.

14.

Move the cursor to SPAN LOWER.

9. Setting the Input Channel

IM XL120P

Keys

Display

SELECT

15.

16.

Show the SPAN LOWER entry window.

Enter 0.0.

17.

SET

Set SPAN LOWER settings.

• To perform measurement:

• To configure other settings:

HOME

SETTING

18.

SET

The changed settings are confirmed.

9. Setting the Input Channel

IM XL120P

10. Setting the Data Save Operation

This chapter explains the steps to save measured data using an example in which the sampling interval is set to 1 min, the data save destination is set to CF card, and the end trigger is set to timer (seven days later). The settings for saving other measured data are not changed from the default settings. For details on the settings for saving measured data, see section 9.1, “Setting the Save Operation of Measured and Calculated Data” in the User’s Manual.

SELECT

Keys

Display

Move the cursor to DATA SAVE.

SETTING

Change to Setting Mode.

Show the DATA SAVE setting screen.

Show the SAMPLING INTERVAL selection list.

SELECT

IM XL120P

SELECT

Move the cursor to 1 min.

Select 1 min.

Move the cursor to SAVE MEDIA.

SELECT

Show the SAVE MEDIA selection list.

Move the cursor to CF CARD.

Keys

Display

10. Setting the Data Save Operation

IM XL120P

SELECT

10.

11.

Confirm CF CARD.

Move the cursor to TRIGGER.

12.

SELECT

Show the TRIGGER setting screen.

13.

Move the cursor to END TRIGGER.

Keys

Display

SELECT

14.

Show the END TRIGGER setting screen.

10. Setting the Data Save Operation

IM XL120P

15.

16.

SELECT

Show the TRIGGER TYPE selection list.

17.

Move the cursor to TIMER.

Keys

Display

SELECT

18.

Select TIMER.

19.

Move the cursor to TIMER.

SELECT

Show the TIMER SETTINGS window.

10. Setting the Data Save Operation

IM XL120P

20.

21.

Enter 0168:00:00.

Keys

Display

SET

Set END TRIGGER settings.

• To perform measurement:

• To configure other settings:

HOME

SETTING

22.

SET

The changed settings are confirmed.

10. Setting the Data Save Operation

IM XL120P

11. Confirming the Settings and Performing the Measurement

When you are done with the settings, press

HOME

to switch to Free Running

Mode and check the settings.

The figure below shows the display that appears when the XL100 is configured

as explained in section chapter 9, “Setting the Input Channel” and 10, “Setting

the Data Save Operation.”

Check whether the displayed values are correct. If the measured values are not

correct, switch back to Setting Mode, and check that the input settings are

correct. If the measured values are not correct even though the input settings

are correct, see chapter 14, “Troubleshooting.”

If the CF Card icon is gray, the save destination is not set to the CF card.

Sampling interval

CF card icon

Measured value

Scale upper limit

Scale lower limit

TIP

• To switch to a display other than waveform & digital display, press DISPLAY to show the display switch pop-up menu, select the display using the arrow keys, and press SELECT. (The steps are explained in page 22.)

• Press TIME/DIV to switch the time axis (the time per grid (division)).

• Press RANGE to change the input range or span (scale).

IM XL120P

12. Inserting an External Storage Medium and Saving Data

Inserting an External Storage Medium

CF cards (Type II) and SD cards can be used on the XL100 as external storage

media.

For the handling precautions of the external storage media, the estimated

amount of stored data, and other information, see section 4.7, “Inserting and

Removing the External Storage Media” in the User’s Manual.

Inserting or Removing a CF Card

Insert the CF card firmly into the CF card slot on the side panel of the XL100.

To remove the CF card, press the CF card eject button to the left of the CF card

slot, and pull the CF card out.

CF card eject button

CF card slot

CF card

Inserting or Removing a SD Card (Supported only on the XL121,

XL122, and XL124)

Insert the SD card firmly into the SD card slot on the side panel of the XL100.

To remove the SD card, press the SD card, and then pull it out.

SD card slot

SD card

IM XL120P

Starting the Data Save Operation

To start the data save (logging) operation, press

START / STOP

. When the data save

operation starts, the START LED illuminates. If a start trigger (see page 18) is

specified, the logging operation starts when the trigger condition is met. The

START LED blinks until the trigger condition is met.

HOME

REVI

TIME

RANGE

START

/ STOP

START/STOP key

START LED

Usage Indication of the External Storage Media

The amount of space used is displayed using a blue bar with respect to the total

space on the storage medium that is specified to be the save destination of the

measured data.

Total space on the save destination medium

Used space

Free space

Stopping the Data Save Operation

Press

START / STOP

. If a stop trigger (see page 18) is specified, the logging operation

stops automatically when the trigger condition is met.

TIP

•A file name “YYMMDDhhmmss.DLO” (YY: year, MM: month, DD: day, hh: hour, mm: minute, ss: second) is automatically assigned to measurement data files (“YYMMDDhhmmss.CSV” if the data type is set to ASCII). You can also assign an arbitrary file name. For the procedure to assign an arbitrary file name, see section 9.1, “Setting the Save Operation of Measured and Calculated Data” in the User’s Manual.

• The measured/calculated data (instantaneous values) can be saved by pressing SAVE in Free Running Mode. For the procedure to save the data manually, see section 9.3, “Manually Saving Measured and Calculated Data” in the User’s Manual.

• The saved data file can be renamed, deleted, or copied to another external storage medium in File Operation Mode. For these operations, see sections 9.7 to 9.9 in the User’s Manual.

• If the data fails to be written to the save destination for some reason, the data is saved to the backup memory. For details on the backup memory, see section 9.1, “Manually Saving Measured and Calculated Data” in the User’s Manual.

12. Inserting an External Storage Medium and Saving Data

IM XL120P

13. Analyzing the Saved Data

Loading the Saved Data File

The steps to load measured data saved to a CF card is given below.

TIP

If you press REVIEW in Logging Mode, the XL100 switches to Logging & Review Mode (see page 21).

SELECT

Keys

Display

Change to Review Mode.

Show the LOAD FILE window.

Show the LOAD FILE selection list.

SELECT

REVIEW

Move the cursor to CF CARD.

IM XL120P

Move the cursor to the file shown in the FILE area.

Select the file.

Keys

Display

SET

The file is loaded, and the data is displayed as shown in the figure on the right.

Select CF CARD.

SELECT

13. Analyzing the Saved Data

IM XL120P

Loading the Measured Data

Two markers (three markers including marker ALM when an alarm is activated) are shown in Review Mode. A measured value at an arbitrary position can be read by moving the markers horizontally.

Active maker

Marker A

Time difference between the markers

Marker B

Measured value at marker A

Measured value at marker B

Difference in the measured values or calculated values

Time at the active marker position

Selecting the Marker

Press

MAR

to select marker A and B alternately. The selected marker (active

marker) is displayed with a thick line.

Moving the Marker

Press the left or right arrow key. Hold the key down to move the marker quickly.

Moving the Marker by One Division

Press (fast forward key) to move the active marker to the left or right

by one division.

Displaying Statistical Calculation Values

Press

DISPLA

in Review Mode to display the maximum, minimum, average, peak

(P-P), and rms values from the start to the end of the logging operation. Press

to perform statistical calculation between markers A and B. Press

DISPLA

again to return to the marker display.

Statistical calculation values

13. Analyzing the Saved Data

IM XL120P

14. Troubleshooting

The table below lists the major symptoms and their corrective actions. For the

procedure to check the items under “Things to Check”, see the referenced

section written in section 12.1, “Troubleshooting” in the User’s Manual. For the

corrective action for error messages, see the referenced section written in

section 12.2, “Messages and Their Corrective Actions” in the User’s Manual.

Symptom Things to Check

Nothing appears even when For AC power operation the power is turned ON. • Check that the power cord is properly connected to the

power outlet.

• Check that the power supply is within the allowed supply voltage range.

For battery operation

• Check that the battery is loaded correctly.

• Check that the battery is charged adequately.

The measurement display • Check that noise is not riding on the input is odd. signal.

• Check that the wires are correctly connected.

• Check that the ambient temperature and humidity are within the allowed specifications.

Keys do not work. Check that the key lock ( ) is not shown at the upper

right corner of the display.

Unable to save/load from the • Turn the power switch OFF and then back internal memory. ON. It may be restored by the power-on self-test.

• There may have been a power problem while the internal memory was being accessed. Format the internal memory in File Operation Mode. Note that the data saved in the memory will be lost in the process.

Unable to save/load from the • Check that the external storage medium is correctly external storage medium. inserted.

• Check that the external storage medium is formatted.

• Check that there is sufficient free space on the external storage medium.

Unable to set or control the • Check that the communication parameters are matched. instrument using • Check that the specifications of the cable is suitable for communication commands. the application.

• Check that the electrical specifications are correct.

Unable to print. • Check that the printer is turned ON.

• Check that the specifications of the connection cable are correct.

• Check that the cable is correctly connected.

• Check that the communication parameters on the XL100 and printer are matched.

• Check that the chart is loaded correctly in the printer.

IM XL120P

Index

e-mail transmission 20 elapsed time 13 ESC key 7 external storage medium 39 external trigger 18

fast forward key 7, 43 FILE key 7, 21 File Operation Mode 21 file operations 18 format 18 Free Running Mode 21 front panel 6 FTP server 19

grid 12 GROUP key 7 group name 9

hold 11 HOLD key 7 HOME key 7, 21, 38

icons 9 input settings 29 input type 15 internal memory 9, 17, 18

key lock 11 keys 6

AC adapter 11, 26 accessories 4 active channel 12 active marker 43 alarm 16, 18 alarm data 17 alarm function 16 alarm line 12 alarm output status 9 alarm status 9 alarm summary display 14 arrow keys 7

backup file 17 backup memory 11 bar graph display 13 battery 8, 11 battery, remaining power 11

CF card 10, 17, 39 channel No. 13 character entry 23 CHARGE LED 6 communication function 19 copy backup memory 18 copy data 18

data save operation, setting of 33 data save operation, starting of 40 data save operation, stopping of 40 data, saving of 17 date/time 9 DC current 25 DC voltage 15, 25 differential calculation 15 digital display 13 DISPLAY key 7, 22, 43 display switching 22

IM XL120P

level 18 load setting data 18 log data 17 log display 14 logging & review display 14 Logging & Review Mode 21 logging data 17 Logging Mode 21 logic 15

manual print 11 manual sampled data 17 MARK key 7, 43 marker 43 measured data, loading of 43 menu switching 22 Modbus 11, 20 model 4

operation mode 9, 21

Pen 12 POWER LED 6 power supply, connection of 26 power switch, turning ON/OFF of 27 printer 11 pulse 15

RANGE key 7 rear panel 8 rename 18 review display 14 REVIEW key 7, 21, 41 Review Mode 21, 43 RS-232 8, 20 RS-485 8, 20 RTD 15, 25

sampling interval 9, 33 SAVE key 7 save setting data 18 saved data file, loading of 41 scale 12 screen image data 17 SD card 10, 39 SELECT key 7 serial communication 20 SET key 7 setting data 17 SETTING key 7, 21, 29, 33 Setting Mode 21 side panel 8 signal input wiring 24 START LED 6, 40 START/STOP key 7, 21, 40 Statistical Calculation 15 statistical calculation 43 status display section 6, 9 storage media, usage indication bar of 12

tag 13 terminal block unit 6 terminal cover 24 thermocouple 15, 25, 29 time 18 time axis 12 TIME/DIV key 7 timer 18, 33 triggers 18

unit 13 usage indication of the external storage media 40 USB 20 user name 9

values, entry of 23

Index