Operator's Manual
21" Rear & Side Discharge
Mulching Lawn Mower
Model Series 430
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A. FORM NO. 769-00564B
(10/2003)
TABLEOFCONTENTS
Content
Important Safe Operation Practices
Slope Gauge
Assembling Your Lawn Mower
Know Your Lawn Mower
Operating Your Lawn Mower
Maintaining Your Lawn Mower
Page Content Page
3 Servicing Your Lawn Mower 13
6 Making Adjustments 14
7 Off Season Storage 15
9 Trouble Shooting Guide 15
10 Illustrated Parts 16
12 Warranty 20
FINDINGMODELNUMBER
This Operator's Manual is an important part of your new lawn mower. It will help you assemble, prepare and
maintain the unit for best performance. Please read and understand what it says.
Before you start assembling your new equipment, please locate the model plate on the
equipment and copy the information from it in the space provided below. A sample model plate is
also given below. You can locate the model plate by standing at the operating position and
looking down at the rear of the deck. This information will be necessary to use the
manufacturer's web site and/or help from the Customer Support Department or an authorized
service dealer.
Copy the model number here:
'_RD_BN)/_ MTD LLC
www.yardman.com 330-220-4683
P. O. BOX 361131
CLEVELAND,0H 44136
800-800-7310
Copy the serial number here:
CUSTOMERSUPPORT
Please doNOTreturntheunitto the retailer fromwhereit waspurchased,withoutfirstcontactingCustomerSupport.
If you have difficulty assembling this product or have any questions regarding the controls, operation or
maintenance of this unit, you can seek help from the experts. Choose from the options below:
Visit yardman.com for many useful suggestions. Click on Customer Support button and you
will get the four options reproduced here. Click on the appropriate button and help is
immediately available.
answer you are
looking for could be just
a mouse c//cA awayf
If you prefer to reach a Customer Support Representative, please call 1-800-800-7310.
,r f
answer are
looking for could be just
a mouse c//cA away!
" f
M nual
En ine
The engine manufacturer is responsible for all engine-related issues with regards to
performance, power-rating, specifications, warranty and service. Please refer to the engine
manufacturer's Owner's/Operator's Manual, packed separately with your unit, for more
information.
SECTION1: IMPORTANTSAFEOPERATIONPRACTICES
WARNING" This symbol points out important safety instructions which, if not followed, could endanger
the personal safety and/or property of yourself and others. Read and follow all instructions in this manual
before attempting to operate this machine. Failure to comply with these instructions may result in personal
injury. When you see this symbol--HEED ITS WARNING
WARNING" This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can result in
serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to
observe the following safety instructions could result in serious injury or death.
WARNING" Engine exhaust, some of its constituents, and certain vehicle components contain or
emit chemicals known to State of California to cause cancer and birth defects or other
reproductive harm.
GeneralOperation
1. Read this operator's manual carefully in its entirety
before attempting to assemble this machine. Read,
understand, and follow all instructions on the
machine and in the manual(s) before operation. Be
completely familiar with the controls and the proper
use of this machine before operating it. Keep this
manual in a safe place for future and regular
reference and for ordering replacement parts.
2. This machine is a precision piece of power
equipment, not a plaything. Therefore, exercise
extreme caution at all times. Your unit has been
designed to perform one job: to mow grass. Do not
use it for any other purpose.
3. Never allow children under 14 years old to operate
this machine. Children 14 years old and over
should read and understand the operation
instructions and safety rules in this manual and
should be trained and supervised by a parent. Only
responsible individuals who are familiar with these
safe operation rules should use this machine.
4. Thoroughly inspect the area where the equipment
is to be used. Remove all stones, sticks, wire,
bones, toys and other foreign objects which could
be tripped over or picked up and thrown by the
blade. Thrown objects can cause serious personal
injury. Plan your mowing pattern to avoid discharge
of material toward roads, sidewalks, bystanders
and the like. Also, avoid discharging material
against a wall or obstruction which may cause
discharged material to ricochet toward operator.
5. To help avoid blade contact or a thrown object
injury, stay in the operator zone behind the handles
and keep bystanders, helpers, children and pets at
least 75 feet from the machine while it is in
operation. Stop machine if anyone enters the area.
6. Always wear safety glasses or safety goggles
during operation and while performing an
adjustment or repair to protect your eyes. Thrown
objects which ricochet can cause serious injury to
the eyes.
7. Wear sturdy, rough-soled work shoes and close-
fitting slacks and shirts. Shirts and pants that cover
the arms and legs and steel-toed shoes are
recommended. Never operate this machine in bare
feet, sandals, slippery or light weight (e.g. canvas)
shoes.
8. Do not put hands or feet near rotating parts or
under the cutting deck. Contact with the blade can
amputate hands and feet.
9. A missing or damaged discharge cover can cause
blade contact or thrown object injuries.
10. Many injuries occur as a result of the mower being
pulled over the foot during afall caused by slipping
or tripping. Do not hold on to the mower if you are
falling; release the handle immediately.
11. Never pull the mower back toward you while you
are walking. If you must back the mower away from
a wall or obstruction first look down and behind to
avoid tripping and then follow these steps:
a. Step back from the mower to fully extend
your arms.
b. Be sure you are well balanced with sure
footing.
c. Pull the mower back slowly, no more than
half way toward you.
d. Repeat these steps as needed.
5. Do not operate the mower while under the influence
of alcohol or drugs.
6. Do not engage the self-propelled mechanism on
units so equipped while starting engine.
7. The blade control handle is a safety device. Never
attempt to bypass its operation. Doing so makes
the safety device inoperative and may result in
personal injury through contact with the rotating
blade. The blade control handle must operate
easily in both directions and automatically return to
the disengaged position when released.
8. Neveroperatethemowerinwetgrass.Alwaysbe
sureofyourfooting.Aslipandfallcancause
seriouspersonalinjury.Ifyoufeelyouarelosing
yourfooting,releasethebladecontrolhandle
immediatelyandthebladewillstoprotatingwithin
threeseconds.
9. Mowindaylightorgoodartificiallight.Walk,never
run.Stopthebladewhencrossinggraveldrives,
walkwaysorroads.
10.Iftheequipmentshouldstarttovibrateabnormally,
stoptheengineandcheckimmediatelyforthe
cause.Vibrationisgenerallyawarningoftrouble.
11.Shuttheengineoffandwaituntilthebladecomes
toacompletestopbeforeremovingthegrass
catcheroruncloggingthechute.Thecuttingblade
continuestorotateforafewsecondsafterthe
engineisshutoff.Neverplaceanypartofthebody
inthebladeareauntilyouaresurethebladehas
stoppedrotating.
12.Neveroperatemowerwithoutpropertrailshield,
dischargecover,grasscatcher,bladecontrol
handleorothersafetyprotectivedevicesinplace
andworking.Neveroperatemowerwithdamaged
safetydevices.Failuretodoso,canresultin
personalinjury.
13.Mufflerandenginebecomehotandcancausea
burn.Donottouch.
14.Onlyusepartsandaccessoriesmadeforthis
machinebytheoriginalequipmentmanufacturer
(O.E.M).Failuretodosocancausepersonalinjury.
15.Ifsituationsoccurwhicharenotcoveredinthis
manual,usecareandgoodjudgment.Contactyour
dealerforassistance.Telephone1-800-800-7310
forthenameofyournearestdealer.
DoNot:
1. Do not mow near drop-offs, ditches or
embankments, you could lose your footing or
balance.
2. Do not mow slopes greater than 15 degrees as
shown on the slope gauge.
3. Do not mow on wet grass. Unstable footing could
cause slipping.
Children
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the mower and the mowing activity. They do not
understand the dangers. Never assume that children
will remain where you last saw them.
1. Keep children out of the mowing area and under
the watchful care of a responsible adult other than
the operator.
2. Be alert and turn mower off if a child enters the
area.
3. Before and while moving backwards, look behind
and down for small children.
4. Use extreme care when approaching blind corners,
doorways, shrubs, trees, or other objects that may
obscure your vision of a child who may run into the
mower.
5. Keep children away from hot or running engines.
They can suffer burns from a hot muffler.
6. Never allow children under 14years old to operate
a power mower. Children 14 years old and over
should read and understand the operation
instructions and safety rules inthis manual and
should be trained and supervised by a parent.
SlopeOperation
Slopes are a major factor related to slip and fall
accidents which can result in severe injury. Operation
on slopes requires extra caution. If you feel uneasy on a
slope, do not mow it. Before operating this unit on a
slope or hilly area, use the slope gauge on page 6 to
measure slopes. If the slope is greater than 15 degrees,
do not mow it.
Do:
1.
Mow across the face of slopes; never up and down.
Exercise extreme caution when changing direction
on slopes.
,
Watch for holes, ruts, rocks, hidden objects, or
bumps which can cause you to slip or trip. Tall
grass can hide obstacles.
,
Always be sure of your footing. A slip and fall can
cause serious personal injury. If you feel you are
losing your balance, release the blade control
handle immediately, and the blade will stop rotating
within 3 seconds.
Service
SafeHandlingof Gasoline
1. To avoid personal injury or property damage use
extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.
Serious personal injury can occur when gasoline is
spilled on yourself or your clothes which can ignite.
2. Wash your skin and change clothes immediately.
3. Use only an approved gasoline container.
4. Never fill containers inside avehicle or on a truck or
trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
5. Ifpossible, remove gas-powered equipment from
the truck or trailer and refuel it on the ground. If this
is not possible, then refuel such equipment on a
trailer with a portable container, rather than from a
gasoline dispenser nozzle.
6. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
7. Extinguishallcigarettes,cigars,pipesandother
sourcesofignition.
8. Neverfuelmachineindoorsbecauseflammable
vaporswillaccumulateinthearea.
9. Neverremovegascaporaddfuelwhiletheengine
ishotorrunning.Allowenginetocoolatleasttwo
minutesbeforerefueling.
10.Neveroverfillfueltank.Filltanktonomorethan½
inchbelowbottomoffillernecktoprovidespacefor
fuelexpansion.
11.Replacegasolinecapandtightensecurely.
12.Ifgasolineisspilled,wipeitofftheengineand
equipment.Moveunittoanotherarea.Wait5
minutesbeforestartingtheengine.
13.Neverstorethemachineorfuelcontainerinside
wherethereisanopenflame,sparkorpilotlightas
onawaterheater,spaceheater,furnace,clothes
dryerorothergasappliances.
14.Toreducefirehazard,keepmowerfreeofgrass,
leaves,orotherdebrisbuild-up.Cleanupoilorfuel
spillageandremoveanyfuelsoakeddebris.
15.Allowamowertocoolatleast5minutesbefore
storing.
GeneralService
1. Never run an engine indoors or in a poorly
ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
2. Before cleaning, repairing, or inspecting, make
certain the blade and all moving parts have
stopped. Disconnect the spark plug wire and
ground against the engine to prevent unintended
starting.
3. Check the blade and engine mounting bolts at
frequent intervals for proper tightness. Also,
visually inspect blade for damage (e.g., bent,
cracked, worn) Replace blade with the original
equipment manufacture's (O.E.M.) blade only,
listed in this manual. "Use of parts which do not
meet the original equipment specifications may
lead to improper performance and compromise
safety!"
4. Mower blades are sharp and can cut. Wrap the
blade or wear gloves, and use extra caution when
servicing them.
5. Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
6. Never tamper with safety devices. Check their
proper operation regularly.
7. After striking aforeign object, stop the engine,
disconnect the spark plug wire and ground against
the engine. Thoroughly inspect the mower for any
damage. Repair the damage before starting and
operating the mower.
8. Never attempt to make a wheel or cutting height
adjustment while the engine is running.
9. Grass catcher components, discharge cover, and
trail shield are subject to wear and damage which
could expose moving parts or allow objects to be
thrown. For safety protection, frequently check
components and replace immediately with original
equipment manufacturer's (O.E.M.) parts only,
listed in this manual. "Use of parts which do not
meet the original equipment specifications may
lead to improper performance and compromise
safety!"
10. Do not change the engine governor setting or
overspeed the engine. The governor controls the
maximum safe operating speed of the engine.
11. Maintain or replace safety and instruction labels, as
necessary.
12. Observe proper disposal laws and regulations.
Improper disposal of fluids and materials can harm
the environment.
YourResponsibility
• Restrict the use of this power machine to persons
who read, understand and follow the warnings and
instructions in this manual and on the machine.
/ WARNING
USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY.
¢O
U.I
.=1:
u.I
a=
nl
0'3
&i
Z
I--
U.I
0'3
I
15°
_kWARNING
Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn
and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain your footing and you could slip,
resulting in serious injury.
Operate RIDING mowers up and down slopes, never across the face of slopes.
Operate WALK-BEHIND mowers across the face of slopes, never up and down slopes.
SECTION3: ASSEMBLINGYOURLAWNMOWER
RemovingUnitFromCarton
• Remove staples, break glue on top flaps or cut tape
at carton end and peel top flap to open carton.
• Remove loose parts if included with unit.
• Cut corners and lay carton down flat. Remove
packing material.
• Roll or slide unit out of carton. Check carton
thoroughly for loose parts.
NOTE: Make sure not to crimp cables while removing
the loose parts or the entire unit from the carton.
HardwarePack
Please identify each piece
of the hardware pack as
shown here.
Wing
Nut
1/4-20 (2)
Carriage
Bolt
1/4-20 (2)
ToolsRequired
• Pair of Pliers
• Funnel
NOTE: Reference to right or left hand side of the mower
is observed from the operating position.
• Raise the lower handle, as shown in Figure 2, until
it snaps into place.
• Raise the upper handle as shown in Figure 2.
• Tighten the two wing nuts which are already on the
handle. See Figure 3.
Figure 2
Tighten these
wing nuts
DisconnectingSparkPlug
• Before setting up your lawn mower, disconnect the
spark plug wire from the spark plug. See Figure 1.
Spark Plug
Wire
,,
,!!j J I_
_,lJ II-
Spark Plug
Figure 1
AssemblingHandle
• For shipping purposes, the grass bag was placed
on top of the unit. Remove it from the unit and set it
out of the way. See Figure 2.
Lower
Upper
Handle
Figure 3
NOTE: Make sure to route the cables outside the lower
handle. Also do not crimp the cables while lifting the
handle up.
• Remove the hairpin clips from the outer hole in the
weld pins on the handle bracket assemblies. Using
a pair of pliers, squeeze one leg of the lower handle
against the handle bracket assemblies. Insert the
hairpin clip into the inner hole on the weld pin.
Repeat on other side. See Figure 4.
• After you have moved the hairpin clip, install the
carriage bolt, (carriage bolt must go to the inside of
handle) included in the hardware pack, inthe upper
hole on the handle mounting bracket. Secure with
one plastic wing nut, also included in the hardware
pack. See Figure 4. Repeat process on other side.
Handle
AssemblingGrassCatcher
Carriage Bolt
Upper_
Hole
Handle
Mounting
Wing Nut
Move H _inClip
Figure 4
Fasten the cable to the lower handle with the two
cable ties found on the lower handle. Pull the cable
ties tight and trim off the excess. See Figure 5.
Cable Tie
Post on _
Cable
NOTE: If your mower's grass catcher has been already
assembled before shipping, proceed to the next
section. Ifit is unassembled, follow the steps below.
Insert frame into grass bag with the black plastic
side on the bottom of bag. See Figure 7.
Insertframe
Frame
Figure 7
• Slip the side openings of the plastic channel on the
bag over the hooks on the grass catcher frame.
Secure bag to the frame by working the six plastic
channels on bag over frame.
• All the plastic channels attach from the outside of
bag. See Figure 8.
Plastic
Channel
Grass Catcher
Figure 5
AttachingStarterRope
• The rope guide is attached to the right side of upper
handle. Loosen the wing nut which secures the rope
guide. See Figure 6.
• With the spark plug wire disconnected and
grounded, hold the blade control handle against the
upper handle, and pull the starter rope out of the
engine. Release the blade control handle. Slip the
starter rope into the rope guide. Tighten wing nut.
Slip rope into
rope gu__, jing Nut
Rope
Guide
Figure 8
AttachingGrassCatcher
• Lift the rear discharge door and place the grass
catcher on the pivot rod. Let go of discharge door so
that it rests on the grass catcher. See Figure 9.
Figure 6
Figure 9
RemovingGrassCatcher
• Lift the rear discharge door on the mower, and lift
the grass catcher up.
• Release the rear discharge door.
ConvertingtoSide-Discharge
• Your mower has been shipped as a mulcher. To
convert it to a side-discharge mower, lift the
mulching plug. Slide the two hooks on the side-
discharge deflector under the hinge pin on the
mulching plug assembly. Lower the mulching plug.
See Figure 10.
Mulching
Plug
Pin ge
fSide
Chute
Deflector
Figure 10
• Do not remove the side mulching plug at any time,
even when you are not mulching.
_ ARNING: Never operate the mower
without the mulching cover, the grass catcher
bag, or the discharge chute properly installed.
SECTION4: KNOWYOURLAWNMOWER
Read this owner's manual and safety rules before operating your lawn mower. Compare the illustrations in Figure
11 with your lawn mower to familiarize yourself with the location of various controls and adjustments.
Blade Control
Handle
Recoil Starter _
Grass
Spark Plug
Mulch Plu(
Side-Discharge /
Chute
BladeControlHandle
The blade control handle is located on the upper handle
of the mower. The blade control handle must be
depressed in order tooperate the unit. Release the
blade control handle to stop the engine and the blade.
Figure 11
,_ WARNING: The blade control handle is asafety device. Never attempt to bypass its
Height Adjustment
Lever
operations. The blade will be rotating whenever
the engine is running.
CuttingHeightAdjustmentLever
This lever, located at each wheel, lets you adjust cutting
height of the grass. Remember to put all four levers at
the same height to avoid uneven cut.
ThrottleControl
The engine is equipped with a constant speed throttle
for maximum engine and cutting performance.
RecoilStarter
The recoil starter is attached to the handle. Stand
behind the unit and pull the recoil starter to start engine.
Primer
The primer is used to pump gas into the carburetor. Use
it to assist in starting a cold engine, but do not use it
when restarting a warm engine after a short shutdown.
MulchingPlug
The mulching plug is used only for mulching purposes.
Instead of collecting the grass clippings in a grass
catcher, some mower models have the option of
recirculating the clippings back to the lawn. This is
called mulching.
SECTION5: OPERATINGYOURLAWNMOWER
GasandOilFill-Up
,i_ WARNING" Never fill fuel tank indoors, or
• Service the engine with gasoline and oil as
when engine is running or hot. Do not smoke
when filling up the fuel tank.
instructed in the separate engine manual packed
with your mower. Read instructions carefully.
BeforeStartingMower
• Attach spark plug wire to spark plug. Make certain
the metal cap on the end of the spark plug wire is
fastened securely over the metal tip on the spark
plug.
StartingEngine
,_ WARNING" Be sure no one other than theoperator is standing near the lawn mower while
starting engine or operating mower.
WARNING: Never run engine indoors or in
enclosed, poorly ventilated areas. Engine
exhaust contains carbon monoxide, an
odorless and deadly gas.
• Push the primer three times. Wait two seconds
between each push. In temperatures below 55° F,
prime five times. Do not prime to restart awarm
engine after a short shutdown.
• Standing behind the mower, depress the blade
control handle and hold it against the upper handle.
• Grasp starter handle and pull rope out slowly until
engine reaches start of compression cycle (rope
will pull slightly harder at this point). Let the rope
rewind slowly. Pull rope with a rapid, continuous,
full arm stroke. Keeping a firm grip on the starter
handle, let the rope rewind slowly.
NOTE: See your engine manual packed with your unit
for more detailed instructions.
StoppingEngine
• Release blade control handle to stop the engine
and the blade.
• Disconnect spark plug wire and move away from
spark plug to prevent accidental starting.
WARNING" Keep hands, feet, hair and
loose clothing away from any moving parts on
engine and lawn mower.
10
OperatingYourLawnMower
• Once the engine has started, squeeze the blade
control handle against the upper handle to run the
lawn mower.
• Do not operate the mower without the mulching
cover, the grass catcher bag, or the discharge
chute properly installed.
• Be sure that the lawn is clear of stones, sticks, wire,
or other objects which could damage lawn mower
or engine. Such objects could be accidently thrown
by the mower in any direction and cause serious
personal injury to the operator and others.
• For best results, do not cut wet grass because it
tends to stick to the underside of the mower,
preventing proper discharge of grass clippings,
poor mulching conditions, and could cause you to
slip and fall. New grass, thick grass, or wet grass
may require a narrower cut.
• For a healthy lawn, always cut off one-third or less
of the total length of the grass. Lawn should be
trimmed in fall as long as there is growth.
,_ WARNING" Ifyou strike a foreign object,
stop the engine. Remove spark plug wire from
spark plug, thoroughly inspect the mower for
any damage. Repair the damage before
restarting and operating the mower. Extensive
vibration of the mower during operation is an
indication of damage.
BaggingGrassClippings
You can use the grass catcher bag to collect clippings
while you are operating the mower.
• Attach the grass catcher following instructions on
page 8 of this manual. Grass clippings will
automatically collect in the bag as you run mower.
• Operate mower till the grass bag is full.
• Stop the engine completely by releasing the control
handle. Make sure that the unit has come to a
complete stop.
• Lift discharge door and pull grass bag up and away
from the mower to dispose of the grass clippings.
UsingtheMulcher
• For effective mulching, do not cut wet grass
because it tends to stick to the underside of the
deck, preventing proper mulching of grass
clippings. New or thick grass may require a
narrower cut. The ground speed should be
adjusted to the condition of the lawn. Ifmowing has
been delayed and the grass has been allowed to
grow in excess of 4", mulching is not
recommended. Mow using the grass bag (if so
equipped) to reduce the grass height to 3-1/4"
maximum before mulching.
AdjustingCuttingHeight
Refer to height adjustments section of this manual on
page 14 for instruction on how to adjust the cutting
height and the handle height.
• For best results in mowing, keep the cutting height
position high until you have determined which
cutting height is preferred.
11
SECTION6: MAINTAININGYOURLAWNMOWER
IMPORTANT:Make sure to avoid muffler and
WARNING" Always stop engine and
disconnect spark plug wire before performing
any maintenance or adjustments on the mower.
surrounding areas while the mower engine is hot
because temperature of these areas of the engine may
exceed 150° F.
WARNING: Never tip mower more than 90
degrees in any direction and do not leave it
tipped for long. Oil can drain into the upper part
of the engine causing a starting problem.
CleaningtheLawnMower
• Clean underside of the mower deck after each use
to prevent any build-up of grass. Ifthis debris
accumulates, it will cause rust and corrosion.
NOTE: We do not recommend the use of pressure
washers or garden hose to clean your unit. These may
cause damage to bearings or the engine. The use of
water will result in shortened life and reduced
serviceability.
• Disconnect spark plug wire. Drain gasoline from the
mower, or place a piece of plastic under gas cap.
• Tilt the mower so that the side with the air cleaner is
facing up. Hold the mower firmly.
• Scrape and clean the underside of the deck with a
suitable tool. Do not spray with water.
• Put mower back on its wheels and remove plastic.
EngineMaintenance
A list of key maintenance jobs required for good
performance by the mower is given below. Follow the
engine manual for detailed list and instructions.
• Change engine oil as specified in the engine
manual. Check oil level before starting engine
every time.
• Service foam filter in the air cleaner as specified in
the engine manual. Service air filter more frequently
in extremely dusty conditions.
• Clean engine periodically. Remove dirt and debris
with a cloth or brush.
• Clean spark plug and reset the gap to.030" at least
once a season or every 50 hours of operation.
• Inspect muffler periodically, and replace if
necessary. Damaged mufflers or spark arresters
can create a fire hazard.
Lubrication{seeFigure12)
Wheels
• Lubricate the wheels and bearings, if so equipped,
at least once a season with light oil or engine oil.
Also, if the wheels are removed for any reason,
lubricate the surface of the pivot arm axle and the
inner surface of the wheel with light oil.
ChuteDeflector& RearDischargeDoor
• Lubricate the torsion spring and the pivot point on
each end of the rear discharge door using a light oil.
This will prevent rusting.
Engine
• Follow the engine manual instructions and
recommended schedule for lubricating engine.
Pivot Points
• Lubricate the pivot points on the discharge chute
door, blade control handle and the cutting height
adjustment lever at least once aseason with light
oil. The blade control handle must operate freely in
both directions. The cutting height adjustment
levers should be able to move easily.
Lubricate
EL
Follow engine manual
for lubrication
/
Lubricate
12
Figure 12
SECTION7: SERVICINGYOURLAWNMOWER
BladeCare
Periodically inspect the blade adapter and pulley for
cracks, especially if you strike a foreign object. Replace
when necessary.
,_ WARNING" When removing the cutting
To Sharpen Blade:
• The blade can be sharpened with a file or on a
• Follow the original angle of grind as a guide. Make
blade for sharpening or replacement, protect
hands by using heavy gloves or a thick rag to
grasp the cutting blade.
Disconnect spark plug wire from spark plug.
Turn mower on its side making sure that the air filter
and the carburetor are up.
Remove the bolt and blade support which holds the
blade and adapter to the engine crankshaft. See
Figure 13. Remove the blade and adapter from the
crankshaft.
Blade Adapter
Blade
Hex Bolt
Figure 13
grinding wheel. Do not attempt to sharpen the
blade while it is still on the mower.
sure that each cutting edge receives an equal
amount of grinding to prevent an unbalanced blade.
NOTE: An unbalanced blade will cause excessive
vibration when rotating at high speeds, may cause
damage to the mower and could break causing
personal injury.
The blade can be tested by balancing iton a round
shaft screwdriver. See Figure 14. Remove metal
from the heavy side until it balances evenly. It is
recommended that the blade always be removed
from the adapter for the best test of balance.
1. Insertscrew driver through hole
d!
2. Bladeshould be parallel to ground
Screw
Driver _ _ Blade
I. O_(_) O
Ground
Figure 14
• Before reassembling the blade and the blade
adapter to the unit, lubricate the engine crankshaft
and the inner surface of the blade adapter with light
oil (or engine oil). Also lubricate the bolt hole and
bolt.
• Install the blade adapter on the crankshaft with the
"star" away from the engine. Refer to Figure 13.
Place the blade with the side marked bottom (or
with part number) facing away from the adapter.
• Align the blade bell support over the blade with the
tabs in the holes of the blade and insert the hex
bolt. Tighten the center bolt to 450 in. Ibs. min., 600
in. Ibs. max.
IMPORTANT:Toensure safe operation, all nuts and
bolts must be checked periodically for correct tightness.
13
ReplacingRearFlap
• To remove rear flap, cut off the flat end of the wire
rod which secures it to the deck. See Figure 15.
Attach the new flap and new rod to deck, bending
the ends of the new rod over to secure to deck.
Rear Discharge
; raandkl:t Door
SECTION8: MAKINGADJUSTMENTS
AdjustingHandleHeight
Your mower is shipped with the handle in the higher
height position. To lower height, proceed as follows.
• Remove the starter rope from the rope guide.
• Remove the upper handle by removing the hand
knobs and carriage bolts. Lay upper handle out of
the way, being careful not to bend or kink cables.
• Remove the hairpin clips from the weld pins on the
handle brackets. Refer to Figure 4.
• Remove the carriage bolts and wing nuts from the
handle brackets. Press out on the legs of the lower
handle. Remove lower handle from the mower.
• Turn the lower handle
around so the notch on
the bottom of the lower
handle isfacing forward
as shown in the box
here. Reassemble,
placing the bottom Lower _h
holes in the handle over
the weld pins in the
handle mounting
bracket.
• Reassemble the upper
handle to the lower handle.
• Insert hairpin clips in the inner holes of the weld
pins and replace the carriage bolts and wing nuts
on the handle brackets. Attach the starter rope as
instructed in the "Assembling Your Lawn Mower"
section.
\
Handle
__;__ _ Handle
Figure 15
Rear Flap Bracket
AdjustingCuttingHeight
IMPORTANT: All wheels must be placed inthe same
relative position. For rough or uneven lawns, move the
height adjustment lever to a higher position. This will
help stop scalping of the grass.
An adjusting plate and
thumb lever at each wheel
position provides cutting
height adjustment. Each
adjusting plate has nine
height positions. Height of
cut will change when you
move the thumb lever
from one position to
another.
Simply depress the
lever towards the
wheel and move the lever assembly to desired
position. See the illustration in the box above.
Adjustment
Lever
AdjustingCarburetor
NOTE: A dirty air cleaner may cause an engine to run
rough too. Make sure that the air cleaner is clean and
attached to the carburetor before deciding to adjust the
carburetor.
,i_ WARNING: If any adjustments are made tothe engine (e.g. carburetor) while the engine is
running, keep clear of all moving parts. Be
careful of heated surfaces like the muffler.
To adjust carburetor, please follow the engine manual.
14
SECTION9: OFF-SEASONSTORAGE
Prepare your lawn mower for storage at the end of the
season or if the unit will not be used for 30 days or
more. Store the mower in a clean, dry area.
Gasoline
• Do not store gasoline from one season to another.
Gasoline, stored more than one month, may affect
engine performance.
• Replace your gasoline can if it starts to rust. Rust
and/or dirt in the gasoline will cause problems.
Engine
• Follow recommendations in the accompanying
engine manual for off-season storage of the
engine.
Mower
• Store unit in a clean, dry area. Do not store next to
corrosive materials, such as fertilizer or rocksalt.
• Clean underside of the mower according to
instructions on page 12.
NOTE: We do not recommend the use of pressure
washers or garden hose to clean your unit. They may
cause damage to bearings or the engine. The use of
water will result in shortened life and reduce
serviceability.
• Lubricate the mower as instructed on page 12.
• You can fold your mower's handle for convenience
of storage.
• Inspect and replace/sharpen blade, if required.
Refer to page 13.
NOTE: If storing the mower in an unventilated or metal
storage shed, make sure to rustproof the equipment
with a light oil or silicone.
SECTION10: TROUBLE-SHOOTINGGUIDE
Problem Possible Cause Corrective Action
Engine fails to start
Engine runs erratic
Engine overheats
Occasional skip at high 1. Spark plug gap too close
speed
Idles poorly 1. Spark plug fouled, faulty, or gap too wide 1. Reset gap or replace spark plug.
Excessive vibration 1. Cutting blade loose or unbalanced 1. Tighten blade and adapter, balance blade.
Fails to mulch grass 1. Wet grass 1. Wait until grass is dry to cut.
Uneven cut 1. Wheels not in same height position 1. Reposition all wheels at same height.
NOTE: For repairs beyond the minor adjustments fisted above, contact your nearest authorized service dealer.
1. Blade control handle disengaged
2. Spark plug wire disconnected
3. Fuel tank empty, or stale fuel
4. Blocked fuel line
5. Faulty spark plug
6. Engine flooded
1. Spark plug wire loose
2. Blocked fuel line or stale fuel
3. Vent in gas cap plugged
4. Water or dirt in fuel system
5. Dirty air cleaner
1. Engine oil level tow
2. Air flow restricted
2. Dirty air cleaner 2. Clean air cleaner.
2. Bent cutting blade 2. Replace blade.
3. Bent engine crankshaft 3. Contact your nearest service center
2. Excessively high grass 2. Mow once at a high cutting height, then
3. Dull blade 3. Sharpen or replace blade.
2. Dull blade 2. Sharpen or replace blade.
1. Engage blade control handle.
2. Connect wire to spark plug.
3. Fill up tank with fresh gasoline.
4. Clean fuel line.
5. Clean, adjust gap, or replace.
6. Wait a few minutes and start again.
1. Connect and tighten spark plug wire.
2. Clean fuel line, fill tank with clean, fresh
gasoline.
3. Clear vent.
4. Drain fuel tank. Refill with fresh fuel.
5. Clean air cleaner. Refer to engine manual.
1. Fill crankcase with proper oil.
2. Clean lawn mower engine.
1. Adjust gap to.030 inches.
mow again at desired height.
15
SECTION11:PARTSLISTFORMODELSERIES430
3
2
15
52
55
41
37
18
19_
55\
39
23 2]
16
@
46
45
@
_4238_25
43
\
25
21
16
1 If Equipped
ModelSeries430
Ref. Part No.
No.
1. 747-1161A
2. 710-1205
3. 720-0279
4. 710-1174
5. 720-0284
6. 749-1092A
7. 749-0928A
8. 726-0240
9. 747-04080
10. 746-1130
746-1137
11. 664-04027
12. 714-0104
13. 732-04090
14. 732-04089
15. 731-04134
16. 732-1014
17. 747-0710
18. 732-0700
19. 731-1236
20. 748-0376C
21. 710-1044
22. 736-0524A
23. 17032A
24. 742-0741
25. 712-0431
26. 15261A
27. 687-02077
687-02076
28. 732-0404
29. 738-0507B
Description
Control Handle
Rope Guide
Handle Knob 1/4-20 Thd.
Curved Hd. Bolt 5/16-18 x 2"
Hand Knob
Upper Handle
Lower Handle
Cable Tie
Grass Catcher Frame
Control Cable - 40"
Control Cable - 53"
Grass Bag
Int. Cotter Pin 5/16" Dia.
Door Spring - R.H.
Door Spring - L.H.
Rear Discharge Door
Torsion Spring
Hinge Pin
Wire Rod
Rear Flap
Blade Adapter w/Star
Hex Bolt 3/8-24 x 1.5" Lg.
Blade Bell Support
Deflector Chute Adapter
21" Mulching Blade w/Star
Flange Nut 3/8-16 Thd.
Height Adj. Plate
Pivot Arm Assembly - RH (8" Wheels)
Pivot Arm Assembly - LH (7" Wheels)
Pivot Arm Assembly - LH (8" Wheels)
Pivot Arm Assembly - RH (7" Wheels)
Front Spring Lever
Shld. Bolt.5" Dia. x.357"
Ref.
No.
_lfEquipped
Part No.
30.
736-0504_
31.
720-0426
32.
732-04175
33.
687-02074
687-02100
687-02075
687-02099
34.
687-02071
687-02070
35.
782-5002A
36.
710-0654A
37.
782-5003
38.
710-1017
39. 710-1652
40. 787-01144
41. 787-01143
42. 787-01104
43. 734-04086
734-2004A
44. 736-0270
45. 687-02055
46. 731-04177
47. 710-0599
48. 782-5004A
49. 736-0451
51. 710-0703
52. 712-0397
53. 750-04162
54. 747-04035
55. 734-04087
734-2004A
56. 731-1426A_
57. 731-1506_
Description
Wave Washer
Spring Lever Knob
Rear Spring Lever
Height Adj. Assy. Comp.- RH (8" Whl)
Height Adj. Assy. Comp. - RH (7" Whl)
Height Adj. Assy. Comp. - LH (8" Whl)
Height Adj. Assy. Comp. - LH (7" Wht)
Pivot Arm R.H.
Pivot Arm L.H.
Front Baffle
Hex L-Wash.Scr. 3/8-16 x 1"
Rear Baffle - LH
Torx Mach AB-Tap Scr. 1/4 x.62"
HexlndWash. Scr. 1/4-20:.625
Handle Bracket - RH
Handle Bracket - LH
Deck 21"
Front Wheel 7" x 1.8"
Front Wheel 8" x 2.125"
Bell Washer 1/4" I.D.
Hinged Mulching Plug
Side Chute Deflector
Hex Hd Self-Tp Scr. 1/4-20 x.5"
Rear Baffle - RH
Shoulder Washer
Hex Carriage Screw 1/4-20
Wing Nut
Spacer,.375OD x.501D
Rear Door Pivot Rod
Rear Wheel 8" x 1.8"
Rear Wheel 8"x 2.125"
Hub Cap - Radial Spoke Yellow
Front Cover
17
NOTES
18
NOTES
19
MANUFACTURER'S LIMITED WARRANTY FOR:
YaRD.MaNTM
®
The limited warranty set forth below is given by MTD LLC with
respect to new merchandise purchased and used in the
United States, its possessions and territories.
"MTD" warrants this product against defects in material and
workmanship for a period of two (2) years commencing on the
date of original purchase and wilt, at its option, repair or
replace, free of charge, any part found to be defective in
materials or workmanship. This limited warranty shall only
apply if this product has been operated and maintained in
accordance with the Operator's Manual furnished with the
product, and has not been subject to misuse, abuse,
commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of
other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not
approved by MTD for use with the product(s) covered by this
manual will void your warranty as to any resulting damage.
Normal wear parts or components thereof are subject to
separate terms as follows: All normal wear parts or
component failures wilt be covered on the product for a period
of 30 days regardless of cause. After 30 days, but within the
two year period, normal wear part failures will be covered
ONLY IF caused by defects in materials or workmanship of
OTHER component parts. Normal wear parts and
components include, but are not limited to: batteries, belts,
blades, blade adapters, grass bags, rider deck wheels, seats,
snow thrower skid shoes, shave plates, auger spiral rubber,
and tires.
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE, through your local authorized
service dealer. To locate the dealer in your area, check your
Yellow Pages, or contact MTD LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, or call 1-800-800-7310 or log
on to our Web site at www.mtdproducts.com.
This limited warranty does not provide coverage inthe
following cases:
a,
The engine or component parts thereof. These items
may carry a separate manufacturer's warranty. Refer
to applicable manufacturer's warranty for terms and
conditions.
b,
Log splitter pumps, valves, and cylinders have asepa
rate one year warranty.
C.
Routine maintenance items such as lubricants, filters,
blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal
deterioration of the exterior finish due to use or
exposu_.
d,
MTD does not extend any warranty for products sold or
exported outside of the United States, its possessions
and territories, except those sold through MTD's
authorized channels of export distribution.
e,
Replacement parts that are not genuine MTD parts.
f.
Service completed by someone other than an
authorized service dealer.
g,
Transportation charges and service calls.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty, whether written or oral, except as
mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product,
shall bind MTD. During the period of the warranty, the
exclusive remedy is repair or replacement of the product
as set forth above.
The provisions as set forth in this warranty provide the
sole and exclusive remedy arising from the sale. MTD
shall not be liable for incidental or consequential loss or
damage including, without limitation, expenses incurred
for substitute or replacement lawn care services or for
rental expenses to temporarily replace a warranted
product.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions or
limitations may not apply to you.
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of safety features of the product shall void this warranty.
You assume the risk and liability for toss, damage, or injury to
you and your property and/or to others and their property
arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased
as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This
limited warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
IMPORTANT:Owner must present Original Proof of
Purchase to obtain warranty coverage.
MTD LLC, P.O.BOX361131CLEVELAND,OHIO44136-0019; Phone:1-800-800-7310
Loading...