Yamaha YSP-5600 User Manual

Digital Sound Projector

Owner’s Manual

English

for Europe model

Read the supplied booklet “Quick Reference Guide” before using the unit.

FEATURES 4

What you can do with this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Preparing remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Controls and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PREPARATIONS 11

General setup procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

a Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

b Connecting a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

c Connecting playback devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

d Other connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Connecting a subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Wired network connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

e Connecting the power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

f Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Displaying the menu screen on the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Selecting the language for menu display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Auto setup for appropriate surround effects (IntelliBeam) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Operating the unit by TV’s remote control (HDMI control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

PLAYBACK 37

Basic operation for playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Enjoying sound based on your preference . . . . . . . . . . . . . . . . . . . . . . . . 38

Playback with 3D surround sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Playback with surround sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Enjoying three-dimensional surround sound (CINEMA DSP 3D/CINEMA DSP) . . . . . . . . . . . . . . . . . . . . . . . . 39

2-channel playback (stereo playback mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Delivering sound to a specified location (target playback mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Playing back digitally compressed formats (such as MP3, etc.) with enriched sound

(Compressed Music Enhancer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Clear playback of human voices (CLEAR VOICE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Adjusting the position from which dialog is heard (Dialog Lift) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Adjusting volume for each channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Using useful features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Saving energy with the Eco function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Switching information displayed in the front panel display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Saving this unit’s settings to system memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Wireless playback of audio via Bluetooth connection . . . . . . . . . . . . . . 46

Listening to music from a Bluetooth device (Receiving) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Listening to audio through Bluetooth speakers or headphones (transmitting) . . . . . . . . . . . . . . . . . . . . . . . 49

En 2

NETWORKS 50

APPENDIX 91

Network functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Connecting to a network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Wired network connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Wireless network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Connecting a mobile device to the unit directly (Wireless Direct) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Playing back music stored on media servers (PCs/NAS) . . . . . . . . . . . . 61

Media sharing setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Playing music files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Listening to Internet radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Playback of Internet radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Registering favorite Internet radio stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Playing back music with AirPlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Playback of iTunes/iPod music contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Playing back music stored on mobile devices . . . . . . . . . . . . . . . . . . . . . 66

Using a mobile device to play songs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

SETTINGS 67

Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Setting the setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Setup menu list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Settings each input source (Option menu) . . . . . . . . . . . . . . . . . . . . . . . . 84

Setting the option menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Option menu list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Advanced setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Setting the advanced setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Advanced setup list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Updating the unit’s firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Using “Network Update” in the setup menu to update firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Updating firmware with connection of a USB flash drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Messages in the front panel display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Status indicator on the wireless subwoofer kit SWK-W16 . . . . . . . . . . 99

When surround effect is not enough . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Installing and adjusting the sound reflection board YRB-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Basic Knowledge of Surround Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

What is a Digital Sound Projector? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

What is Object Based Audio? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Yamaha’s Audio Technologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Network information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

En 3

FEATURES

Audio

Control

Audio

Network contents

Mobile

devices

Control

Audio

Bluetooth

headphones

Mobile

devices

MusicCast devices

HDMI

Control

BD/DVD player

This unit’s

remote control

Audio/ Video*

Audio Audio/

Video*

HDMI

Control

TV remote control

The unit

Audio

Control

Audio

Subwoofer (optional or available

from third-party manufactures)

Wireless subwoofer kit

SWK-W16

* Supports 4K video and HDCP version 2.2

Sound beams are reflected off walls and a ceiling using unique real surround sound formats and techniques, allowing listeners to enjoy their preferred acoustic environment.

• Automatically and quickly adjusts surround sound effects for the listening room setup (IntelliBeam)

. p. 30

• Emphasize the sense of immersion and reality of the sound field with overhead sounds fed via height channels (3D Surround Sound)

. p. 38

• Reproducing stereo or multichannel sounds with the sound fields like actual movie theaters and concert halls (CINEMA DSP 3D/CINEMA DSP)

. p. 39

• Enjoying compressed music with enhanced sound (Compressed Music Enhancer)

. p. 42

• Delivering sound to a specified location (Target playback mode)

. p. 41

Sequential operation of a TV, this unit, and BD/DVD player (HDMI Control)

. p. 35

Listen to audio input to the unit with Bluetooth headphones or speakers

. p. 49

Plays back audio content from Bluetooth

devices

. p. 47

Share music via your home network

. p. 5

Dedicated apps for mobile devices

. p. 5

Wide variety of supported content

• Media server (PC/NAS)

. p. 61

• Internet radio

. p. 62

•AirPlay

. p. 64

• Music stored on mobile devices

. p. 66

What you can do with this unit

FEATURES ➤ What you can do with this unit En 4

Achieve true 3D surround sound including height

The sound image of the system

channel audio with the unit alone

Unrestricted playback of music over a network using MusicCast CONTROLLER

Until now, digital sound projectors have reproduced a two-dimensional sound field with five distinct sound beams: left front, right front, center, left surround, and right surround.

This unit reproduces a three-dimensional sound field offering a greater sense of immersion and depth by directing additional two sound beams (left height and right height) upward. It also enables playback in the DTS:X or Dolby Atmos format, which uses height channel audio signals as input sources. It further incorporates CINEMA DSP 3D, which produces a more effective sound field.

Dialog Lift function

When playing movies, this feature can be adjusted so that audio such as narratives and dialog is output from the center speakers, as in a movie theater where speakers are installed behind the screen, allowing for a sense of integration of conversation with the movements of the actors (p. 42).

The free dedicated app for mobile devices, MusicCast CONTROLLER, allows you to listen to music stored on mobile devices such smartphones, or on servers, or to listen to Internet radio stations and many kinds of major streaming services.

This app also allows you to distribute content to other MusicCast-enabled devices for synchronized playback.

See the “MusicCast Setup Guide” for details. Search for “MusicCast CONTROLLER” on the App Store or Google Play.

Bluetooth

You can receive and play audio from a Bluetooth device, such as a mobile device over a wireless connection. You can also transmit audio input to the unit to a Bluetooth headphones.

functions

Using HOME THEATER CONTROLLER (WLAN) to easily operate the unit

The free dedicated app for mobile devices, HOME THEATER CONTROLLER (WLAN), allows you to easily operate the unit, performing such tasks as configuring sound beams on a visual screen, selecting an input source, and adjusting the volume on a mobile device.

Search for “HOME THEATER CONTROLLER (WLAN)” on the App Store or Google Play.

Wireless subwoofer connection using the wireless subwoofer kit

The unit and the subwoofer can be connected via a wired connection. In addition, a wireless connection can be established using the wireless subwoofer kit (SWK-W16) (p.

25).

• In this manual, iOS and Android mobile devices are collectively referred to as “mobile devices”. The specific type of mobile device is noted in explanations as needed.

FEATURES ➤ What you can do with this unit En 5

About this manual

• In this manual, operations that can be performed using either the front panel keys or the remote control are explained using the remote control.

• indicates supplementary explanations for better use.

• indicates precautions for use of the unit and its feature limitations.

Supplied accessories

Before connecting, make sure you have received all of the following items.

The unit Wireless subwoofer kit (SWK-W16)

Supplied accessories

Remote control Batteries

Optical cable (1.5 m)

(AAA, R03, UM-4) (x2)

Stands (x2) Screws (For the stands; x2) Subwoofer cable (3 m) System control cable (3 m)

Power cable (2 m)

IntelliBeam microphone (6 m) Cardboard microphone stand

• Owner’s Manual CD-ROM • Quick Reference Guide •MusicCast Setup Guide

China model only: Instead of the optical cable, a digital coaxial audio cable is supplied.

The shape of the power cable plug varies depending on where the unit was purchased.

• The supplied optical cable may not be needed depending upon connections.

FEATURES ➤ Supplied accessories En 6

Preparing remote control

Battery × 2 (AAA, R03, UM-4)

Press down on the arrow and slide the cover in the direction in which it points.

Slide the cover back to close it.

Within 6 m

Before installing batteries or using the remote control, be sure to read battery and remote control precautions in “Quick Reference Guide” (separate booklet).

Installing the batteries

Operation range

FEATURES ➤ Supplied accessories En 7

Controls and functions

STATUS

INTELLIBEAM MIC

CONNECT

INPUT

VOLUME

123 4 5 6

798

The unit (front, top)

1 STATUS indicator

Lights to show the system condition. Glows green: Power on Glows red: Power off (when the HDMI control or network

standby is activated) Turns off: Power off

2 (Wi-Fi) indicator

Shows the status of wireless network connection (p. 52).

3 (Bluetooth) indicator

Shows the status of Bluetooth connection (p. 46, 49).

4 Remote control sensor

Receives infrared signals from the remote control (p. 10).

5 Front panel display

Displays the unit’s settings, such as the name of an audio input source or surround mode (p. 44). The setting values are also displayed.

6 INTELLIBEAM MIC jack

For connecting the supplied IntelliBeam microphone (p. 31).

7 INPUT/CONNECT key

INPUT key

Select an audio input source.

CONNECT key

Use to control the unit using the dedicated MusicCast CONTROLLER app for mobile devices. See the MusicCast Setup Guide for details.

8 VOLUME (+/-) keys

Adjust the volume of the unit (p. 37).

9 z key

Turn on/off the unit.

• When the unit is turned off, this unit consumes a small amount of power in order to search for HDMI signals or to receive signals from a network device.

• The front panel display turns on for 3 seconds only when the unit is operated.

• “Dimmer” can adjust the brightness of the front panel display and indicators in the setup menu (p. 78).

FEATURES ➤ Controls and functions En 8

The unit (rear)

• So that the HDMI and NETWORK jacks may be easily located, the illustration of the rear of the unit used in this manual shows their respective positions with the labels used on the unit itself.

IN 1

12 4 7

563

(HDCP2.2)

SYSTEM

SUBWOOFER

CONNECTOR

OUT

AUX2 TV OPTICAL IR-IN IR-OUT

AUX1

1 SYSTEM CONNECTOR jack

Connect to a Yamaha subwoofer so that the subwoofer functions according to the unit’ power on and off (p. 25).

2 SUBWOOFER OUT jack

For connecting to the subwoofer using a wired connection (p. 25).

3 AUX1 analog input jacks

For connecting to a playback device equipped with the analog audio output jacks (p. 24).

4 AUX2 digital coaxial input jack

For connecting to a playback device equipped with a digital coaxial audio output jack (p. 24).

AC IN

UPDATE ONLY

RS-232C

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI

OUT

(ARC)

SYSTEM

SUBWOOFER

AUX2 TV OPTICAL

CONNECTOR

OUT

AUX1

IR-IN IR-OUT

UPDATE ONLY

IN 2

IN 3

IN 4

HDMI

OUT

(ARC)

RS-232C

5 TV and OPTICAL jacks

For connecting to a playback device equipped with an digital optical audio output jack (p. 22, 23).

6 IR-IN, IR-OUT, and RS-232C jacks

They are control expansion jacks for commercial use only.

7 UPDATE ONLY jack

Use to update this unit’s firmware (p. 88).

8 HDMI IN 1–4 jacks

For connecting an HDMI-compatible playback device such as a BD/DVD player, a satellite and cable TV tuner, and a game console (p. 23).

9 HDMI OUT (ARC) jack

For connecting to an HDMI-compatible TV and outputting video/audio signals (p. 22).

NETWORK

0 NETWORK jack

A AC IN jack

NETWORK

For connecting to a network with a network cable (p. 52).

Connect the supplied power cable (p. 27).

FEATURES ➤ Controls and functions En 9

Remote control

d e

f g

j k

l m

5 6

Infrared signal transmitter

1 ECO key

Turn the Eco function on or off (p. 44).

2 Input selector keys, NET key

Input selector keys

Select an audio input source to be played back (p. 37).

NET key

Select an audio input via a network (p. 50). Each time the key is pressed, the input source is selected as follows: SERVER  NET RADIO  AirPlay  Streaming music service (if available)  MusicCast Link  SERVER  …

3 SYSTEM MEMORY keys

Save IntelliBeam measurements, speaker volume, and other settings (p. 45).

4 SUB (+/-) key

Adjust the volume of the subwoofer (p. 37).

5 MUTE ( ) key

Mute the sound (p. 37).

6 SETUP ( ) key

Display the setup menu (p. 67).

7 S/T/W/X keys, ENTER key

Change the setting (p. 67).

8 RETURN ( ) key

Return to the previous menu screen.

9 CINEMA DSP program keys

When playback is in surround playback mode, select the CINEMA DSP programs (p. 39).

0 SURROUND key

Switch to surround playback mode (p. 39).

A 3D SURROUND key

Switch to 3D surround playback mode (p. 38).

B CLEAR VOICE key

Turn the CLEAR VOICE function on or off (p. 42).

C ENHANCER key

Turn Compressed Music Enhancer to on or off (p. 42).

D z key

Turn on/off the unit (p. 37).

E NET RADIO (1–3) keys

F DIALOG LIFT key

Use the Dialog Lift function to adjust the height from which dialog is heard (p. 42).

G VOL (+/-) key

Adjust the volume of the unit (p. 37).

H OPTION ( ) key

Display the option menu for each input source (p. 84).

I INFO ( ) key

Switch the information display on the front panel (p. 44).

J STEREO key

Switch to stereo playback mode (p. 41).

K TA R G E T key

Switch to target playback mode (p. 41).

L WPS/CH LEVEL key

WPS key

Use the key when connecting to a wireless router (access point) that supports the WPS (push button) feature (p. 54).

CH LEVEL key

Adjust the volume balance during playback (p. 43).

M CONNECT key

Use to control the unit using the dedicated MusicCast CONTROLLER app for mobile devices. See the MusicCast Setup Guide for details.

FEATURES ➤ Controls and functions En 10

PREPARATIONS

General setup procedure

1 Installation (p. 12)

2 Connecting a TV (p. 22)

3 Connecting playback devices (p. 23)

4 Other connections (p. 25)

5 Connecting the power cable (p. 27)

6 Initial settings (p. 28)

This completes all the preparations. Enjoy playing movies, music and other content with the unit!

• See “NETWORKS” (p. 50) for information regarding network connection and audio playback via a network.

Position the unit to achieve the optimal surround sound effects. The unit can also be mounted on a wall.

Connect a TV to the unit.

Connect video devices (such as BD/DVD players) to the unit.

Connect a subwoofer. Use a network cable to connect the unit to a router in preparation for wired network connection.

After all the connections are complete, plug in the power cable.

Perform initial setup, such as adjusting surround sound effects, before attempting playback.

PREPARATIONS ➤ General setup procedure En 11

Height channel audio is output in a diagonal direction upward and forward from the unit (p. 5).

Depending upon the rack, table-top stand, or floor stand used, the stands may not be necessary.

• Install the unit in the center of the left and right walls.

• This unit can be mounted on a wall (p. 17).

• The listening position (such as sofa, etc.) should be located at the front of the unit.

• The distance between the listening position and the unit should be more than 1.8 m.

• Set the listening position as far from the back wall as possible (the optimal listening position is halfway between the unit and the back wall, or slightly closer to the back wall).

• To achieve desired surround sound effects, be sure that obstacles such as furniture may not obstruct the path of sound beams (p. 13).

• Be sure that the unit installed with at least 5 cm of empty space above and below it.

• Leaving as much space as possible in a diagonal direction in front of, and above, the unit when installing it.

• Attach the supplied stands to the unit if it will be installed on a rack

(p. 16).

1 2 3 4 5 6

a Installation

This unit reflects sound beams off of walls and a ceiling to create the surround sound effect. The position of this unit in relation to the listening position, walls, and a ceiling is important to achieving the desired surround sound effects. Refer to pages 12 to 16 when installing the unit. When installing this unit on a rack behind which there is limited space, for example, it may be easier to connect external devices to this unit first. This will depend upon the installation location. See pages 22 to 27 for information regarding the connection of external devices.

Notes

• Be sure to install this unit on a large, stable stand where it does not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children.

• There is a built-in antenna on the top of the unit. Do not install it on a metal rack, and do not stack metal items on top of the unit.

• The unit’s speakers are not magnetically shielded. Do not install hard disk drives or similar devices near the unit.

• Do not stack the unit directly on top of other playback devices, or vice versa. Heat and vibrations may result in damage or malfunction.

Recommended place for installation

PREPARATIONS ➤ a Installation En 12

Objects, such as furniture

Parallel installation: Viewed from above

40° to 50°

Objects, such as furniture

Corner installation: Viewed from above

Viewed from the side

Sound beams are reflected off the ceiling

Sound beam output varies depending upon the 3D surround/Surround setting (p. 38, 39) and the channel output setting (p. 73). The illustration above shows the path of sound beams when 3D surround is enabled and “Front” in the Channel Out setting is set to “Beam”.

Viewed from the side

The illustrations above show the path of sound beams when 3D surround is enabled (p. 38) and “Front” in the Channel Out setting is set to “Stereo”. (p. 73).

Sound beams are reflected off the ceiling

More than

1.8 m

More than 1.8 m

1 2 3 4 5 6

Example for installing the unit

This unit outputs sound beam as shown in the illustrations below. Install this unit where there are no obstacles such as furniture obstructing the path of sound beams. Otherwise, the desired surround sound effects may not be achieved.

If the unit is installed so that it is parallel to a wall, install it as close to the exact center of the wall as possible.

If the unit is installed in a corner of a room, position it at a 40–50° angle to the adjacent walls.

Parallel installation

Install this unit as close to the exact center of the wall as possible.

• If the unit cannot be installed evenly between the left and right walls, sound beams can be adjusted to achieve natural surround sound effects (p. 16).

Ideal installation condition

Install this unit as close to the exact front of your normal listening position as possible. The distance between listening position and the unit should be more than 1.8 m.

PREPARATIONS ➤ a Installation En 13

Irregularly shaped rooms with solid walls on all sides

Irregularly shaped rooms that are open to a hallway on one side

1 2 3 4 5 6

Installing in a non-square room

Install this unit so that the sound beams can be reflected off the walls.

• If this unit cannot be repositioned, or the listening position cannot be changed, the optional YRB-100 sound reflection board may be installed for a better surround sound experience (p. 100).

PREPARATIONS ➤ a Installation En 14

Objects, such as

furniture

1 2 3 4 5 6

Example for installing the unit in living room

• The legs on a table are not considered obstacles as sound beams normally pass through them. A cupboard installed facing the wall reflects sounds.

• As the heavy curtains absorb sounds, the sound features of the listening room is different from the case with the curtain opened and the case with the curtain closed. Using saving settings function enables to save the best settings for each case of listening room (p. 45).

Unrecommended listening environments

This unit creates surround sound by reflecting projected sound beams off the walls and the ceiling of your listening room. The surround sound effects produced by this unit may not be sufficient when this unit is installed in the following locations.

• Rooms with walls inadequate for reflecting sound beams

• Rooms with acoustically absorbent walls and ceiling

• Rooms with measurements outside the following range: W (3 to 7 m) × H (2 to 3.5 m) × D (3 to 7 m)

• Rooms where objects such as furniture are likely to obstruct the path of sound beams

• Rooms with less than 1.8 m from the listening position to this unit

• Rooms where the listening position is close to the walls

• Rooms where the listening position is not in front of this unit

• Rooms with a complex shape, such as a slanted ceiling (ceiling lights do not obstruct sound beams)

Enjoying surround effects regardless of conditions (My Surround)

The My Surround function creates rich surround sound effects in rooms with less than optimal surround sound conditions. See “Channel Out” (p. 73) for more information.

PREPARATIONS ➤ a Installation En 15

Left front channel adjusted

When left front channel sound is

unnatural

Stand (supplied)

Screws (supplied) Stand (supplied)

1 2 3 4 5 6

This unit’s AUTO SETUP (p. 30) can be used to automatically adjust sound beams to achieve the optimal surround playback environment according to the listening room setup. In addition to using AUTO SETUP, sound beams can be adjusted manually to achieve surround sound effects best suited to the listening room setup when the unit is installed as described below.

Installing the unit near a corner of the room

When installing the unit near a corner of the room as shown in the illustration below, front channel sound may seem to come from an unnatural direction if beam settings are configured using AUTO SETUP.

Should this occur, adjust the left and right front channels using “Image Location” (p. 72) in the setup menu to achieve more natural sound.

Installing the unit in an irregularly shaped room

When the unit is installed in a room that is not rectangular, sound beams may not be properly reflected off the walls as shown in the illustration below.

Should this occur, perform AUTO SETUP, and then adjust the angle of beam from the channel from which sound is not properly heard using “Horizontal Angle” (p. 70) in the setup menu to achieve even distribution of sound.

Adjusting sound beams to achieve optimal surround sound effects

Installing the stands

Install the stands (supplied) on the bottom of the unit. Align and insert the protrusion on the stands into the holes on the rear panel of the unit as shown in the illustration, and then tighten the screws (supplied) to lock the stands in place. The stands need not be installed when the unit is mounted on a wall using the optional Wall Mount Bracket SPM-K30.

PREPARATIONS ➤ a Installation En 16

Wall Mount Bracket (SPM-K30)

4- 7

24- 7x22

114

730

188 355 182355

26.5

71.5

19.4

112.4

SPM-K30 (optional)

YSP-5600

(mm)

1 2 3 4 5 6

Installing the unit on a rack

The unit can be installed on a shelf, either above or below the TV, on a third-party rack. The rack and the shelf on which the unit is placed should be large enough to allow

adequate ventilation around the unit and the rack should be sturdy enough to support the weight of both the unit and the TV.

Mounting the unit on a wall

The unit can be mounted on a wall using the optional Wall Mount Bracket (such as SPM-K30).

Notes

Instructions for mounting the unit are not included in the Installation Manual supplied with the SPM-K30. Always follow the instructions provided in this Owner’s Manual.

Dimensions when the unit is mounted using the SPM-K30

Be sure to refer to the dimensions below and leave adequate space for ventilation around the unit.

PREPARATIONS ➤ a Installation En 17

730 mm

Large wall mount bracket (left)

Large wall mount bracket (right)

Screw (M4; supplied with the SPM-K30)

4mm self-tapping screws (available from third-party manufacturers)

Washers (available from third-party manufacturers)

Installing into a dray wall

Installing directly into a wall, etc.

25 mm or more

Dry wall

25 mm or more

Beam, etc.

1 2 3 4 5 6

• The SPM-K30 may not be available in some countries or regions.

• When the unit will be installed using the wall mount bracket, all installation work should be performed by a qualified contractor or experienced retail staff. The customer should not attempt to install the unit themselves. Improper installation may cause the unit to fall, resulting in personal injury.

• Installation must be secure enough to bear the weight of the unit and the wall mount bracket, possibly for years to come, and must also be secure enough to withstand vibrations, such as those caused by earthquakes. Improper installation may cause the unit to fall, resulting in personal injury.

• To prevent the unit from falling, attach it to a wall constructed of drywall (plasterboard).

• Be sure to use screws capable of supporting the weight of the wall mount bracket and the unit (with steps 2 and 7). Using items other than the specified screws, such as shorter screws, nails, or double-sided tape, may cause the unit to fall, resulting in personal injury.

• To ensure safety, all screws must be tightened securely. Loose screws may cause the unit to fall, resulting in personal injury.

• Be sure to leave adequate space for ventilation around the unit so that heat generated by the unit is allowed to dissipate. Failure to provide adequate space around the unit may cause the unit to overheat internally, resulting in a fire.

• Do not lean on the unit or apply excessive force to the top of the unit. Doing so may cause the unit to fall, resulting in personal injury.

• Fix cables in place so that they will not become loose. If a foot or hand becomes accidentally entangled in, or catches on, a loose cable, the unit may fall, resulting in personal injury.

• Once the unit is installed, safety checks should be conducted on a regular basis. When the unit is used over an extended period of time, screws can become loose and the installation can weaken due to the passage of time, vibrations, etc.

• Note that Yamaha cannot be held liable for accidents, including falling of the unit, resulting from improper installation of the unit, or for damage to walls.

Assemble the large wall mount bracket.

Align the screw holes A on the left bracket with those on the right bracket, and tighten the screws.

Attach the wall mount bracket assembled in step 1 to the wall.

In order to secure the unit to the wall, the bracket must first be attached to the wall in a manner suited to the structure and quality of the wall.

• In order to secure the unit to the wall, drive six (or more) tapping screws from the outside through the holes in the wall mount bracket.

PREPARATIONS ➤ a Installation En 18

Screws (M4; supplied with the SPM-K30)

Small wall mount bracket (Type B)

Screw hole (left side)

Screw hole (right side)

Screws(M4; supplied with the SPM-K30)

Safety wire

Slip one end through the loop at the other end

Slip the safety wire between the bracket and the projector

1 2 3 4 5 6

Attach the small wall mount brackets to the unit.

Attach the safety wires to the small wall mount brackets (left and

right) to prevent the unit from falling.

PREPARATIONS ➤ a Installation En 19

Fit the hook into the hole.

Slide the unit to the right.

Screws (M6; supplied with the SPM-K30)

Bottom side of the unit

1 2 3 4 5 6

Fit the mounting guide hooks of the small wall mount brackets

attached to the unit into the holes on the left and right sides of the large wall mount bracket and then slide the unit to the right.

• Hold the unit tight with both hands when attaching or removing the unit to or from the wall. Holding the unit loosely could cause the unit to fall, resulting in personal injury.

Align the holes in the large wall mount bracket with the holes in the

bottom of the small wall mount brackets, and then use two of the screws (M6; supplied with the SPM-K30) to secure the unit.

PREPARATIONS ➤ a Installation En 20

Secure the safety wire to the wall.

Screw (available

from third-party

manufactures)

Washer (supplied with the SPM-K30)

Secure the safety wire to the wall.

1 2 3 4 5 6

Pass the screws through the loops of the safety wires and then

tighten the screws to secure the safety wires to the wall.

• Attach the safety wires tight.

• Keep the two other washers for future use.

PREPARATIONS ➤ a Installation En 21

HDMI

(ARC)

OUT

(ARC)

HDMI HDMI

The unit (rear)

HDMI OUT (ARC) jack

ARC-compatible HDMI input

The unit (rear)

HDMI OUT (ARC) jack HDMI input

TV jack Audio output

(digital optical)

1. Remove the cap 2. Check the direction of the plug

1 2 3 4 5 6

b Connecting a TV

Connect a TV to the unit so that video input to the unit can be output to the TV. You can also enjoy playback of TV audio on the unit.

• Use a 19-pin HDMI cable with the HDMI logo printed on it. A cable with a maximum length of 5 m is recommended to prevent degradation of signal quality.

• For playback of 3D and 4K video content, use a high-speed HDMI cable.

• This unit supports HDCP version 2.2, a copy protection technology. To enjoy playback of 4K video, connect the unit to the HDMI IN jack (one compatible with HDCP 2.2) on an HDCP 2.2-compliant TV.

TVs that support Audio Return Channel (ARC)

Connect the TV to the unit with an HDMI cable (not supplied).

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI

OUT (ARC)

NETWORK

SYSTEM

SUBWOOFER

CONNCETOR

OUT

AUX1

When connecting a TV that supports Audio Return Channel (ARC), enable the HDMI control function (p. 77).

• Use an ARC-compatible HDMI cable.

What is Audio Return Channel (ARC)?

In order for the unit to play audio from a TV, the TV must usually be connected to the unit via an audio cable as well as an HDMI cable. If, however, the TV supports Audio Return Channel (ARC), TV audio signals can be input to the unit via the HDMI cable that outputs video signals from the unit to the TV.

UPDATE ONLY

AUX2 TV OPTICAL IR-IN

IR-OUT

RS-232C

TVs that do not support Audio Return Channel (ARC)

Connect the TV to the unit with an HDMI cable (not supplied) and an optical cable.

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI

OUT (ARC)

AUX2 TV OPTICAL IR-IN

UPDATE ONLY

IR-OUT

SYSTEM

SUBWOOFER

CONNCETOR

OUT

AUX1

• If the TV has no optical jack

Connect the audio output jack on the TV to the AUX1 (analog) input jack or AUX2 (digital coaxial) jack on the unit, and set “TV Input” in the setup menu to “Analog [AUX 1]” or “Coaxial [AUX 2]” accordingly (p. 77). TV audio can be played through the unit by pressing the TV key on the remote control.

OUT

(ARC)

NETWORK

RS-232C

HDMI HDMI

OPTICAL

HDMI

PREPARATIONS ➤ b Connecting a TV En 22

HDMI

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI HDMI

The unit (rear)

HDMI IN 1–4 jacks

HDMI output

Video device

The unit (rear)

OPTICAL jack

Audio output

(digital optical)

1. Remove the cap 2. Check the direction of the plug

Video device

To video output jack

To video input jack

1 2 3 4 5 6

c Connecting playback devices

Connect video devices such as BD/DVD players, set-top boxes (STBs) and game consoles to the unit. Depending on the video/audio output jacks available on your video device, choose one of the following connections. We recommend using an HDMI connection if the video device has an HDMI output jack.

HDMI connection

Connect a video device to the unit with an HDMI cable (not supplied).

• This unit supports HDCP version 2.2, a copy protection technology. When using an HDCP 2.2-compliant playback device, such as a set-top box, connect it to the unit via the HDMI IN 1 jack. When connecting playback devices that do not support HDCP version 2.2, any HDMI IN jack (1–4) may be used.

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI

OUT (ARC)

NETWORK

AUX2 TV OPTICAL IR-IN

IR-OUT

UPDATE ONLY

RS-232C

SYSTEM

SUBWOOFER

CONNCETOR

OUT

AUX1

The audio/video played on the video device will be output though the unit by switching input to HDMI 1–4 using the HDMI 1–4 key on the remote control.

• Once the HDMI control function has been activated (p. 35), video and audio content from playback devices can be output from the TV even when this unit is off (HDMI signal pass-through).

• Use a 19-pin HDMI cable with the HDMI logo printed on it. A cable with a maximum length of 5 m is recommended to prevent degradation of signal quality.

• For playback of 3D and 4K video content, use a high-speed HDMI cable.

• When audio from the video device cannot be output via the HDMI jack, use an optical cable to connect the video device to the unit via the digital optical output jack on the video device and the OPTICAL jack on the unit. If the video device is connected to the unit in this way, change “Audio Assign” to “Optical” in option menu (p. 85).

Optical connection

Connect a video device to this unit via the optical cable. Next, connect the video device’s video output to the TV’s video input.

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI

OUT (ARC)

NETWORK

UPDATE ONLY

SYSTEM

SUBWOOFER

AUX2 OPTICAL

CONNCETOR

OUT

AUX1

OPTICAL

IR-IN IR-OUT

RS-232C

The audio played on the video device will be output though the unit by switching input to OPTICAL using the OPTICAL key on the remote control.

PREPARATIONS ➤ c Connecting playback devices En 23

OPTICAL

COAXIAL

AUX2

The unit (rear)

AUX2 (digital

coaxial) jack

Audio output

(digital coaxial)

Video device

To video output jack

To video input jack

The unit (rear)

AUX1 (analog) jacks

Audio output

(analog)

Video device

To video output jack

To video input jack

1 2 3 4 5 6

Coaxial connection

Connect a video device to this unit via a digital coaxial cable. Next, connect the video device’s video output to the TV’s video input.

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI

OUT (ARC)

NETWORK

SYSTEM

SUBWOOFER

CONNCETOR

OUT

AUX1

The audio played on the video device will be output though the unit by switching input to AUX2 using the AUX 2 key on the remote control.

UPDATE ONLY

TV OPTICAL

AUX2

IR-IN IR-OUT

RS-232C

Analog connection

Connect a video device to this unit via a stereo cable (not supplied). Next, connect the video device’s video output to the TV’s video input.

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI

OUT (ARC)

NETWORK

AUX2 TV OPTICAL

UPDATE ONLY

IR-IN IR-OUT

RS-232C

AUDIO

SYSTEM

SUBWOOFER

CONNCETOR

OUT

AUX1

The audio played on the video device will be output though the unit by switching input to AUX1 using the AUX 1 key on the remote control.

PREPARATIONS ➤ c Connecting playback devices En 24

SYSTEM

CONNECTOR

SUBWOOFER

OUT

INPUT SYSTEM

CONNECTOR

The unit (rear)

Subwoofer

SWK-W16

1 2 3 4 5 6

d Other connections

Connecting a subwoofer

A subwoofer can be connected to the unit for use with the unit. There are two ways to connect a subwoofer to the unit: use a third-party RCA monaural cable, or use the wireless subwoofer kit SWK-W16 to connect via a wireless connection.

Connecting a subwoofer via cable

Use a third-party RCA monaural cable to connect the subwoofer to the unit via the monaural input jack on the subwoofer and the SUBWOOFER OUT jack on the unit.

When connecting a Yamaha subwoofer equipped with a system connector, connect a system control cable (or third-party 3.5mm monaural mini plug cable) to the SYSTEM CONNECTOR on the unit. This connection is required to turn the unit and subwoofer on and off at the same time.

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI

OUT (ARC)

NETWORK

AUX2 TV OPTICAL

UPDATE ONLY

IR-IN IR-OUT

RS-232C

SYSTEM

SUBWOOFER

CONNCETOR

OUT

AUX1

Using the wireless subwoofer kit SWK-W16

The wireless subwoofer kit SWK-W16 enables wireless connection of a subwoofer to the unit.

❑ Installing the SWK-W16

Install the SWK-W16 on or near the subwoofer. If subwoofer vibrations cause the SWK-W16 to move when installed on the subwoofer, install it elsewhere or fix it in place so that it does not move.

When the unit is connected to the subwoofer via the cable, set the subwoofer output to “Wired” in the setup menu (p. 74)

• See documentation supplied with the subwoofer for more information.

PREPARATIONS ➤ d Other connections En 25

SUBWOOFER

OUT

SYSTEM

CONNECTOR

INPUT

SYSTEM

CONNECTOR

To an AC wall outlet

Subwoofer cable

(supplied)

To an AC wall outlet

System control cable

(supplied)

SWK-W16

Subwoofer

Status indicator

Rear side

SUBWOOFER

OUT

SYSTEM

CONNECTOR

SUBWOOFER

PAIRING

SUBWOOFER PAIRING button

1 2 3 4 5 6

❑ Connecting the cables

Connect subwoofer cable to the SUBWOOFER OUT jack on the

SWK-W16 and the subwoofer’s input jack.

If the Yamaha subwoofer has a SYSTEM CONNECTOR jack, connect system control cable to the SYSTEM CONNECTOR jack on the SWK-W16 and the subwoofer’s SYSTEM CONNECTOR jack. When the unit is turned on and off, the subwoofer turns on and off at the same time.

Plug the power cables for the subwoofer and the SWK-W16 into an

AC wall outlet.

When the unit is turned on, a wireless connection between the unit and SWK-W16 will be established. The status indicator glows green once the wireless connection is established.

❑ Configuring subwoofer output

Set subwoofer output to “Front/Wireless” (default setting) in the setup menu (p. 74). The unit and the wireless subwoofer kit are automatically connected via wireless

connection when the unit is turned on, or when subwoofer output in the setup menu is set to “Front/Wireless”.

• When using the Yamaha NS-SW300 subwoofer, adjusting subwoofer controls as follows is recommended. (Adjustment values may be changed in accordance with the listening environment or personal preferences.)

– Set VOL (volume) to 4.5

– Set HIGH CUT to 3.5

– Set PHASE to REV (reverse)

– Set B.A.S.S. to MOVIE

• Configure the subwoofer’s setting so that it turns on/off when the unit is turned on/off.

• The wireless subwoofer kit SWK-W16 cannot be used while the subwoofer is connected to the unit via cables.

❑ Pairing the SWK-W16 with the unit

If the indicator on the SWK-W16 flashes red and no sound is coming from the subwoofer during playback, move the SWK-W16 closer to the unit to improve

conditions for wireless communications, and follow the procedure below to pair the SWK-W16 with the unit.

Set “Bass Out” for “Subwoofer” in the setup menu to “Front/

Wireless”.

Select “Pairing” for “Subwoofer” in the setup menu.

• See “Troubleshooting” (p. 93, 99) if the indicator on the wireless subwoofer kit does not glow green.

Use a pointed object, such as a ballpoint pen, to press and hold the

SUBWOOFER PAIRING button on the rear panel of the SWK-W16 for three seconds.

PREPARATIONS ➤ d Other connections En 26

The unit (rear)

To an AC wall outlet

1 2 3 4 5 6

Wired network connections

For a wired connection, connect one end of the network cable to the NETWORK jack on the rear panel of the unit and the other end to a router. For details, refer to “NETWORKS” (p. 50).

e Connecting the power cable

After all the connections are complete, plug in the power cable.

AC IN

SYSTEM

SUBWOOFER

CONNCETOR

OUT

AUX1

(HDCP2.2)

AUX2 TV OPTICAL

IN 1

IN 2

IN 3

IN 4

HDMI

OUT (ARC)

UPDATE ONLY

IR-IN IR-OUT

RS-232C

PREPARATIONS ➤ e Connecting the power cable En 27

TV remote control (example)

Switch input sources

The unit (rear)

Setup Menu

Beam

Sound HDMI Display Information

IntelliBeam

Horizontal Angle Vertical Angle Beam Travel Length Focal Length Image Location Channel Out Subwoofer

OPTION ( )

SETUP ( )

1 2 3 4 5 6

f Initial settings

Displaying the menu screen on the TV

Visual operation of this unit is possible by displaying its menu screen on the TV.

Turn on the unit and the TV, and then use the input button on the TV’s remote control to switch input so that video input from this unit is displayed.

When this unit and the TV are connected as shown below, select “HDMI 1” using the TV’s remote control.

IN 1

(HDCP2.2)

IN 2

IN 3

IN 4

HDMI

OUT

(ARC)

NETWORK

AUX2 TV OPTICAL IR-IN

HDMI

UPDATE ONLY

IR-OUT

RS-232C

HDMI INPUT

123

HDMI

SYSTEM

SUBWOOFER

CONNCETOR

OUT

AUX1

OUT

(ARC)

The menu display

The menu is displayed on the TV screen when the SETUP ( ) key or OPTION ( ) key is pressed. When the TV is receiving HDMI

signals, the menu is superimposed over video content. Press the SETUP ( ) key twice or OPTION ( ) key a second time to cancel menu display.

• The setup menu (p. 67) can only be displayed on a TV screen. It cannot be shown in the front panel display.

PREPARATIONS ➤ f Initial settings En 28

Initial screen display

Share Wi-Fi Settings

You can share the wireless (Wi-Fi) settings of the network with Sound Projector using a device with iOS7 or later.

[ENTER]:Start [RETURN]:Cancel [ ]:OSD Language

OSD Language

ENGLISH

DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS

РУССКИЙ

SVENSKA TÜRK

When the unit is turned on for the first time after purchase, the screen below will be displayed. (“ViewScreen” is shown in the front panel display.)

While this screen is displayed, an iOS device (such as an iPhone) can be used to easily connect the unit to a wireless network. See the Quick Reference Guide for more information.

If you will not use an iOS device to connect to a wireless network, press the RETURN () key.

• You can use this function to connect to a wireless network at any time by selecting “Share Wi-Fi Settings (iOS)” from the setup menu. However, be aware that if a different wireless network, or a Bluetooth device, has already been configured, doing so will erase any previous settings.

• This screen will not be displayed if the unit is connected to a router via its NETWORK jack (wired connection).

• Be aware that if the IntelliBeam microphone is connected while the screen shown above is displayed (p. 30), setup will be canceled, and the screen will switch to the auto measurement screen.

Selecting the language for menu display

Turn the unit and TV on.

Switch the TV’s input to display video input from this unit (p. 28).

Press and hold the SETUP ( ) key until the “OSD Language” menu

appears on the TV.

When the menu is not displayed

• Confirm the following cases.

– The HDMI input jack of your TV and the HDMI OUT (ARC) jack of the unit are connected.

– The input of your TV is set to “HDMI 1” (example).

Use the S/T key to select the desired language and press the

ENTER key.

Settings

, ENGLISH (default), DEUTSCH, FRANÇAIS, ESPAÑOL, ITALIANO, NEDERLANDS,

РУССКИЙ, SVENSKA, TÜRK

Press the SETUP ( ) key to exit the setup menu.

PREPARATIONS ➤ f Initial settings En 29

Auto setup for appropriate surround effects (IntelliBeam)

Remove

Fit in

Run through

Place horizontally

Fit in

IntelliBeam microphone

Upper limit

Within 1 m

Center height of

this unit

Cardboard

microphone stand

Within 1 m

Listening position

1.8 m or more

Lower limit

Center line

IntelliBeam microphone

Cardboard microphone stand

First use the “IntelliBeam” function to adjust each channel so that this unit provides the optimal viewing and listening environment.

• The AUTO SETUP procedure may not be run successfully if this unit is installed in one of the rooms described in “Unrecommended listening environments” (p. 15).

• In order for this unit to provide the optimal listening environment, adjust each channel first using the “IntelliBeam” function. The My Surround function can be used to enjoy rich surround sound in these types of rooms as well. See “Channel Out” (p. 73) for more information.

• Do not connect the IntelliBeam microphone to an extension cable as doing so may result in an inaccurate sound optimization.

Installing the IntelliBeam microphone

Place the IntelliBeam microphone at your normal listening position.

❑ Assembling the supplied cardboard microphone stand

• Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would be when you are seated.

• Position the IntelliBeam microphone so that it is parallel with the floor.

Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects obstruct the path of sound beams.

However, any objects that are in contact with the walls will be regarded as a protruding part of the walls.

PREPARATIONS ➤ f Initial settings En 30

+ 82 hidden pages

Yamaha YSP-5600 User Manual

CONTENTS

FEATURES

What you can do with this unit

Supplied accessories

Preparing remote control

Controls and functions

PREPARATIONS

General setup procedure

a Installation

b Connecting a TV

c Connecting playback devices

d Other connections

Connecting a subwoofer

Wired network connections

e Connecting the power cable

f Initial settings

Displaying the menu screen on the TV

Selecting the language for menu display

Auto setup for appropriate surround effects (IntelliBeam)