Yamaha YSP-3300, YSP-4300 Quick Reference Guide

Quick Reference Guide

UCABGLVFH

English

Installation Connection Settings Playback

Connection

When external devices such as a TV, Blu-ray disc player, and/or game console are connected, audio and video signals are transmitted as shown below.

Audio connection

Video connection

Audio and video connection

This unit: Plays audio from TV broadcasts, Blu-ray discs, etc.

HDMI cable

yTips

Audio return channel (ARC) supported TV

• Connect an HDMI cable to the audio return channel supported jack (the jack with “ARC” indicated) on TV. In this case, you do not need to connect an optical cable.

• Activate the HDMI control function of this unit so as to activate the audio return channel (ARC) (refer to “HDMI setup” in the Owner's Manual).

What is audio return channel (ARC)?

A function transmits digital audio signal output from TV to this unit through an HDMI cable. By this function, an optical cable to connect TV and this unit is not needed.

■ Connecting a game console or satellite/cable TV tuner

■ Connecting the FM antenna (YSP-4300 only)

Connect the supplied FM antenna via the FM ANTENNA jack.

FM antenna

This Quick Reference Guide explains steps to connect external components to this unit and start playback. For detailed operation, refer to the “Owner’s Manual” in the supplied CD-ROM. Check that you received all of the supplied accessories referring to “Supplied accessories” of “Safety and Accessory Information” (separate booklet). For instructions on how to operate or set the external components, refer to the owner’s manual supplied with each component. In this guide, the YSP-CU4300 center unit is used for illustrative purposes.

Installation Connection Settings Playback

Installing YSP-4300/YSP-3300

Center unit Subwoofer

Center unit

• Install the center unit in the center of the left and right walls.

• Place the center unit on a TV stand in front of the TV. Use the TV Remote Repeater function if the center unit obstructs the remote control sensor on the TV (see page 12 of the Owner's Manual). Increase the height of the center unit if the TV stand is too high for center unit installation (see page 12 of the Owner's Manual).

• The listening position (such as sofa, etc.) should be located at the front of the center unit.

• The distance between the listening position and the center unit should be more than 1.8 m (6 ft).

• This unit can be mounted on a wall using WALL MOUNT BRACKET SPM-K20 (option). Refer to the SPM-K20 Install Manual and SPM-K20 Information for YSP-CU4300/ YSP-CU3300.

This unit creates surround effects by reflecting sound beams off the walls of your listening room. The arrows in the diagrams on the right indicate the images of paths of 5-channel sound beams. To achieve desired surround sound effects, install this unit where there are no objects such as furniture obstructing the path of sound beams.

1 Front left channel 4 Surround left channel 2 Center channel 5 Surround right channel 3 Front right channel

Subwoofer

• To prevent sound reflecting off of walls, angle the subwoofer slightly toward the center of the room.

• When installing the subwoofer on a rack, be sure the rack is strong enough to support the subwoofer and that it leaves sufficient space for heat discharge.

• The center unit and subwoofer communicate wirelessly. Subwoofer performance may be affected if the subwoofer is placed on a metal rack, or if there is a metal plate between the subwoofer and the center unit.

• The subwoofer can also be placed on its side (see page 13 of the Owner's Manual).

Parallel installation Corner installation

40° to 50°

Objects, such as furniture

Optical cable

Use to connect a TV that does not support audio return channel (ARC) to this unit.

TV: Plays video from TV broadcasts,

Blu-ray disc player, etc.

HDMI cable

Blu-ray disc player

HDMI cable

Game console

(HDMI compatible)

Satellite and cable TV tuner

(not HDMI compatible)

Optical cable

Composite video cable

• Do not connect the power cable until all connections are completed.

• Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/or jack.

■ Connecting a TV and a Blu-ray disc player

For the cable connection, follow the procedure below.

HDMI cable (optional)

Input the digital audio/video signals of the Blu-ray disc player to this unit.

HDMI cable (optional)

The digital video of the Blu-ray disc player is reflected on TV.

U.S.A., Canada, Europe, Russia, and China models only

Optical cable (supplied)

Play back digital sounds of TV on this unit. y

To AC wall outlet

Video signals

Audio signals

HDMI

OUTPUT

Blu-ray disc player

123

HDMI INPUT

OPTICAL OUTPUT

1. Remove the cap 2. Check the direction of the plug

External device (example) Connecting cable

1 Satellite/cable TV tuner HDMI cable (optional)

HDMI compatible

2 Game console HDMI cable (optional) 3 Game console HDMI cable (optional)

Optical cable (supplied) Composite video cable (optional)

RCA stereo cable (optional) Composite video cable (optional)

To AC wall outlet

U.S.A., Canada, Europe, Russia, and China models only

ANALOG OUTPUT

VIDEO

OUTPUT

VIDEO INPUT

VIDEO

OUTPUT

VIDEO INPUT

not HDMI compatible

HDMI

OUTPUT

Video signals

Audio signals

4 Satellite/cable TV tuner

5 Game console

HDMI

OUTPUT

HDMI

OUTPUT

OPTICAL OUTPUT

yTip

To connect a device with an AUX output jack, connect its AUX output jack to the AUX INPUT DIGITAL (coaxial) jack on this unit via a commercial coaxial digital audio cable.

■ Connecting the wireless subwoofer

To connect the supplied subwoofer to the center unit wirelessly, the same group ID must be assigned to the center unit and subwoofer. The default group ID for both components is A1, enabling wireless connection by simply plugging the subwoofer's power cable into an electrical outlet. When using the transmitter (YIT-W12TX)*, the same group ID must be assigned to the center unit and subwoofer. The default group ID of YIT-W12TX is A1. The LINK indicator lights when the subwoofer is on and the subwoofer and center unit are connected wirelessly.

When the center unit enters standby mode, the subwoofer and LINK indicator turn off.

* For details of YIT-W12TX, refer to “Safety and Accessory Information”

(separate booklet).

■ Preparing remote control

Install the batteries Operation range

Pull up on the latch to release the cover

Insert the protrusions into the slots and close the cover

Battery × 2 (AAA, R03, UM-4)

Group ID switches

A B

A B C

1 2 3

LINK

LINK indicator

Blinks: Establishing

Lights: Connection

To AC wall outlet

1 2 3

LINK

connection

established

Within 6 m (20 ft)

Printed in Malaysia ZD75600 [En] © 2012 Yamaha Corporation

Installation Connection Settings Playback

Carrying out AUTO SETUP for appropriate surround effects

The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.

Place the IntelliBeam microphone at your normal listening position.

Assemble the cardboard microphone stand and place the IntelliBeam microphone on top of it horizontally as shown below.

12345

Fit in

Remove

Fit in

Use the supplied cardboard microphone stand to place the IntelliBeam microphone at the same height as your ears would be when you are seated. Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects obstruct the path of sound beams.

IntelliBeam microphone Upper limit

Center height of this unit

Within 1 m (3.3 ft)

Cardboard microphone stand

1.8 m (6.0 ft) or more

Press the key on the remote control.

The power of this unit turns on.

Listening position

Lower limit

Turn the TV on and switch the TV’s input to display video content from this unit.

When this unit is connected to the HDMI input on the TV (as shown in “Connecting a TV and a Blu-ray disc player” in this Quick Reference Guide), switch the TV’s input to “HDMI1”.

Place horizontally

Center line

Cardboard microphone stand

Run through

IntelliBeam microphone

Make sure that your listening room is as quiet as possible.

For accurate measurement, turn off air conditioner or other devices that make noises.

Note

Follow the instructions below and then leave the room. If you remain in the room, you may obstruct the beam, or the microphone may pick up any sounds you make, possibly resulting in improper configuration of settings. When leaving the room, bring this Quick Reference Guide with you. The AUTO SETUP procedure takes about 3 minutes. Wait outside the room during the AUTO SETUP procedure. To cancel the AUTO SETUP procedure after it is started, press the RETURN key on the remote control.

Press the ENTER key to start the AUTO SETUP procedure and then leave the room within 10 seconds.

The screen automatically changes during the AUTO SETUP procedure. If the AUTO SETUP procedure is complete, this unit rings the chimes and the results will be displayed on the TV. If “ENVIRONMENT CHECK:Failure” is displayed, see page 27 of the Owner’s Manual and run the measurement process again.

yTips

• The results displayed depend on the position of the unit.

• If you hear a buzzer sound and an error message appears on the TV, look for a solution in “If an error message is displayed” on page 27 of the Owner’s Manual. Then press the RETURN key to run the measurement process again.

Press the ENTER key.

Measurement results are applied to this unit.

• You can save the several measurement results pressing the SYSTEM MEMORY key (see page 28 of the Owner's Manual).

ENVIRONMENT CHECK: Success BEAM MODE: 5Beam/Plus2

AUTO SETUP START

Will begin in 10 sec.

Please leave the room

----------

[RETURN]:Cancel

(After 3 min.)

SHOW RESULT

MESUREMENT COMPLETE.

[ENTER]:Save set-up.

[RETURN]:Do not save set-up.

AUTO SETUP COMPLETE

Please remove the MIC

from Sound Projector

and the listening position.

Press [SYSTEM MEMORY] key

to save set-up in the memory.

Installation Connection Settings Playback

Playing back

Confirm that this unit and other audio/video devices are properly connected by playing a DVD or BD on the Blu-ray disc player. The following explains the playback procedure when this unit, TV, and Blu-ray disc player are connected as shown in “Connecting a TV and a Blu-ray disc player” in this Quick Reference Guide.

Press the key to turn on this unit.

Turn on your TV and Blu-ray disc player connected to this

unit.

Press the HDMI1 key to select the Blu-ray disc player as the input source.

HDMI1

Switch the TV’s input to HDMI 1.

Play back a DVD or BD on the Blu-ray disc player.

Press the VOLUME (+/-) key to adjust the volume.

yTip

Use TV remote control to mute the sound from TV.

Press the SURROUND key and then the CINEMA DSP keys

Input source name

to set your sound preferences.

yTips

When this unit does not play back, check the following

• The connection between this unit and Blu-ray disc player.

• The audio output settings of Blu-ray disc player is set to digital sound output.

• The TV’s input is switched to this unit.

■ FM tuning (YSP-4300 only)

Press the FM key.

Press the TUNING / key to specify the frequency.

■ Playing music stored on an iPod via YIT-W12TX

Connect YIT-W12TX to the iPod.

For details of YIT-W12TX, refer to “Safety and Accessory Information” (separate booklet).

Start playback of music stored on the iPod.

■ Playing music stored on a computer via YIT-W12TX

Connect YIT-W12TX to the computer via the USB cable for YIT-W12TX.

USB

Play music stored on the computer.

For details of YIT-W12TX, refer to “Safety and Accessory Information” (separate booklet).

yTip

You can select the language for the menu display. Press and hold the SETUP key until the “OSD LANGUAGE” menu appears. Press the S/T key to select the desired language. Press the SETUP key again to exit the setup menu.

Connect the IntelliBeam microphone to the INTELLIBEAM MIC jack on the rear of the unit.

AUTO SETUP

(PREPARATION & CHECK)

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from Sound Projector. The MIC should be set

at ear level when seated.

Measurement takes about 3min.

After [ENTER] is pressed,

please leave the room.

IntelliBeam microphone (supplied)

Cardboard microphone stand (supplied)

[ENTER]:Start [RETURN]:Cancel

Remove the IntelliBeam microphone.

Keep the IntelliBeam microphone in a safe place. The settings are automatically saved in the system memory.

■ Enjoying TV in surround sound

Select the desired TV channel.

Press the TV key.

yTip

HDMI control function

You can use the TV remote control to operate this unit if your TV supports the HDMI control function. See page 31 of the Owner’s Manual.

Playing music stored on an iPod or USB device over a USB connection (YSP-4300 only)

■

Connect the iPod to the USB jack on the front of this unit using the USB cable supplied with

Connect a USB device to the USB jack on the front of this unit.

the iPod.

For more information on playing music stored on the iPod, refer to “Playing music stored on an iPod or USB device over a USB connection” in the Owner's manual.

For detailed operation, refer to the Owner’s Manual on the supplied CD-ROM.

For more information on playing music stored on USB device, refer to “Playing music stored on an iPod or USB device over a USB connection” in the Owner's manual.