Sound beams are reflected off walls using unique real surround sound
formats and techniques, allowing listeners to enjoy their preferred
acoustic environment.
• Automatically and quickly adjusts surround sound
effects for the listening room setup (IntelliBeam)
• Reproducing stereo or multichannel sounds with the
sound fields like actual movie theaters and concert
halls (CINEMA DSP)
• Enjoying compressed music with enhanced sound
(Compressed Music Enhancer)
• Delivering sound to a specified location (Target
playback mode)
. p. 32
. p. 40
. p. 45
. p. 44
HDMI
Control
Audio
HDMI Control
Audio/
Video
BD/DVD playerGame consoleSet-top boxThis unit’s
HDMI
Control
AudioAudio/
Audio/
Video
Video
TV remote control
Center unit (the unit)
HDMI
Control
Audio/
Video
remote control
Sequential operation of a TV, AV receiver,
and BD/DVD player (HDMI Control)
. p. 37
Control
Audio
Bluetooth devices
Plays back audio content from
Bluetooth
Simple operation using the
HOME THEATER CONTROLLER
FEATURES ➤ What you can do with this unitEn4
®
devices
. p. 48
. p. 50
PREPARATIONS
About this manual
• In this manual, operations that can be performed using either the front panel keys or the remote control
are explained using the remote control.
Supplied accessories
Before connecting, make sure you have received all of the following items.
The YSP-2500
Center unit (YSP-CU2500)Wireless subwoofer (NS-WSW120)
• indicates supplementary explanations for better use.
• indicates precautions for use of the unit and its feature limitations.
• According to the connection, the supplied optical cable may not be needed.
IntelliBeam microphone
(6 m (19.7 ft))
Cardboard microphone standNon-skid pads (8 pcs)
* (China model only) Instead of the optical cable, a coaxial digital
audio cable is supplied.
PREPARATIONS ➤ Supplied accessoriesEn5
Controls and functions
Center unit (front, top)
789
STATUS
12 3456
1 Remote control sensor
Receives infrared signals from the remote control (p. 9).
2 Remote control sensor of a TV
Receives infrared signals from the TV remote control when
the TV Remote Repeater function is enabled (p. 15).
3 STATUS indicator
Lights to show the system condition.
Glows green: Power on
Glows red: Power off (when the HDMI control or Bluetooth
standby is activated)
Turns off: Power off
4 Front panel display
Shows information about the operational status of this unit
(p. 8).
5 PHONES jack
For connecting the headphones (p. 44).
6 INTELLIBEAM MIC jack
For connecting the supplied IntelliBeam microphone (p. 33).
7 INPUT key
Selects the playback device (p. 39).
8 VOLUME (+/-) keys
Adjusts the volume of the unit (p. 39).
9 z key
Turns on/off the unit.
PHONES INTELLIBEAM MIC
• When the unit is turned off, this unit consumes a small amount of
power in order to search for HDMI signals or to receive infrared
signals from the remote control.
PREPARATIONS ➤ Controls and functionsEn6
Center unit (back)
12 3 4567
SYSTEM
SUBWOOFER
OUT
RL
CONNECTOR
AUX1
AUX2TVOPTICAL
HDMI
OUT (ARC)IN1IN2
IN3
SYSTEM
SUBWOOFER
RL
CONNECTOR
AUX2 TV OPTICAL
OUT
AUX1
OUT (ARC)IN1IN2
1 SYSTEM CONNECTOR jack
For connecting to the supplied subwoofer using a wired
connection (p. 29).
2 SUBWOOFER OUT jack
For connecting to the supplied subwoofer using a wired
connection (p. 29).
3 AUX1 analog input jacks
For connecting to a playback device equipped with the
analog audio output jacks (p. 27).
4 AUX2 coaxial digital input jack
For connecting to a playback device equipped with a coaxial
digital audio output jack (p. 27).
HDMI
IN3
89
5 TV/OPTICAL jacks
For connecting to a playback device equipped with an
optical digital audio output jack (p. 25, 26).
6 HDMI OUT (ARC) jack
For connecting to an HDMI-compatible TV and outputting
video/audio signals (p. 25).
7 HDMI IN 1–3 jacks
For connecting an HDMI-compatible playback device such
as a BD/DVD player, a satellite and cable TV tuner, and a
game console (p. 26).
8 TV Remote Repeater
Receives signals from a TV remote control via the front of the
center unit and transmits those signals to the TV when the TV
Remote Repeater function is activated (p. 15).
9 Power cable
For connecting to an AC wall outlet (p. 28).
PREPARATIONS ➤ Controls and functionsEn7
Front panel display
2 34567891
0A
1 HDMI indicator
Glows when HDMI signals are input.
2 HD indicator
Glows when HD audio signals (Dolby TrueHD, Dolby Digital
Plus, DTS-HD Master Audio, DTS-HD High Resolution, DTS
Express, or Multi-channel Linear PCM) are input.
3 SUR. indicator
Glows when multichannel audio signals are input.
4 TARGET indicator
Glows when target playback mode is enabled (p. 44).
5 UNIVOLUME indicator
Glows when the UniVolume function is enabled (p. 46).
6 ENHANCER indicator
Glows when the Compressed Music Enhancer function is
enabled (p. 45).
7 REPEATER indicator
Glows when the TV Remote Repeater function is enabled
(p. 15).
8 TX indicator
Glows while the wireless connection to the subwoofer is
being established (p. 29).
9 VOL indicator
Indicates the current volume level (p. 39).
0 CINEMA DSP indicator
Glows when a CINEMA DSP program is selected (p. 40).
A Multi information display
Displays an input source and surround information (p. 46).
Displays settings and information as alphanumeric
characters.
• Note that the front panel display turns off when the Eco function is
enabled and remains off unless an operation is performed.
• “DIMMER” can adjust the brightness of the front panel display in the
setup menu (p. 60).
• HD audio signals offer a higher quality sound than do conventional
digital audio signals.
PREPARATIONS ➤ Controls and functionsEn8
Remote control
Infrared signal transmitter
1E
2
3
F
G
4
H
5
I
6
J
7
8
K
9
0
L
A
B
C
M
N
D
1 ECO key
Turns the Eco function on or off (p. 46).
2 SURROUND key
Switches to surround playback mode (p. 40).
3 STEREO key
Switches to stereo playback mode (p. 44).
4 Input selector keys
Select the playback device (p. 39).
5 SYSTEM MEMORY keys
Saves IntelliBeam measurements, speaker volume, and
other settings (p. 47).
6 SUB (+/-) key
Adjusts the volume of the subwoofer (p. 39).
7 MUTE ( ) key
Mute the sound (p. 39).
8 SETUP ( ) key
Displays the setup menu (p. 51).
9 S/T/W/X keys, ENTER key
Change the setting (p. 51).
0 RETURN ( ) key
Returns to the previous menu screen.
A CINEMA DSP program keys
When playback is in surround playback mode, select the
CINEMA DSP programs (p. 40).
B UNIVOLUME key
Turns the UniVolume function on or off (p. 46).
C ENHANCER key
Turns Compressed Music Enhancer to on or off (p. 45).
D REPEATER key
Turns the TV Remote Repeater function on or off (p. 15).
E z key
Turns on/off the unit (p. 39).
F BEAM key
Switches the sound beam output method (p. 42).
G TAR GET key
Switches to target playback mode (p. 44).
H CLEAR VOICE key
Turns the CLEAR VOICE function on or off (p. 45).
I CH LEVEL key
Adjusts the volume balance during playback (p. 45).
J VOL (+/-) key
Adjusts the volume of the unit (p. 39).
K OPTION ( ) key
Displays the option menu for each input source (p. 63).
L INFO ( ) key
Switches the information display on the front panel (p. 46).
M BLUETOOTH STANDBY key
Turns the Bluetooth standby mode on or off (p. 50).
N SUBWOOFER PAIRING key
Used to pair the center unit with the subwoofer manually
(p. 75).
PREPARATIONS ➤ Controls and functionsEn9
Subwoofer
FrontBack
1 Connection indicator
Shows subwoofer’s connection status (p. 29).
Glows green: Power on
Glows red: Power off
2 INPUT jack
For connecting to the center unit using a wired connection
(p. 29).
3 SYSTEM CONNECTOR jack
For connecting to the center unit using a wired connection
(p. 29).
1
2
3
4
4 SUBWOOFER PAIRING key
Used to pair the center unit with the subwoofer manually
(p. 75). Use a pin or other pointed object to press this key.
5 Heat discharge unit
Discharges heat generated inside the subwoofer. Do not
cover the heat discharge unit.
6 Power cable
For connecting to an AC wall outlet (p. 28).
INPUT
SYSTEM CONNECTOR
SUBWOOFER PAIRING
5
6
INPUT
SYSTEM CONNECTOR
SUBWOOFER PAIRING
PREPARATIONS ➤ Controls and functionsEn 10
Installation
This unit reflects sound beams off of walls to create the surround sound effect. The position of this unit in relation to both the listening position and walls is important to achieving the
desired surround sound effects. When installing this unit on a rack behind which there is limited space, for example, it may be easier to connect external devices to this unit first. This
will depend upon the installation location. See “Connections” (p. 24) for more information.
Notes
• Be sure to install this unit on a large, stable stand where it does not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children.
• The subwoofer speakers are not magnetically shielded. Do not install hard disk drives or similar devices near the subwoofer.
• Do not stack the center unit and subwoofer directly on top of other playback devices, or vice versa. Heat and vibrations may result in damage or malfunction.
Recommended place for installation
• Install the center unit in the center of the left and right
walls.
• Place the center unit on a TV stand in front of the TV*.
• This unit can be mounted on a wall using the optional
Wall Mount Bracket SPM-K20 (p. 19).
* Use the TV Remote Repeater function if the center unit
obstructs the remote control sensor on the TV (p. 15).
If the center unit cannot be installed on a TV stand
because the stand is too high, the height of the center
unit can be adjusted (p. 16).
• The listening position (such as sofa, etc.) should be
located at the front of the center unit.
• The distance between the listening position and the
center unit should be more than 1.8 m (6 ft).
Center unit
• To prevent sound reflecting off of walls, angle the
subwoofer slightly toward the center of the room.
• When installing the subwoofer on a rack, be sure
the rack is strong enough to support the subwoofer
and that it leaves sufficient space for heat
discharge.
• The subwoofer can also be placed on its side
(p. 18).
Subwoofer
• To achieve desired surround sound effects, be
sure that obstacles such as furniture may not
obstruct the path of sound beams (p. 12).
❑ Wireless connections
The center unit and subwoofer communicate wirelessly. Subwoofer performance may be affected if the subwoofer is placed on a metal rack, or if there is a metal plate between the
subwoofer and the center unit. Use a wired connection to connect the subwoofer to the center unit if sounds are interrupted due to the installation condition (p. 29).
PREPARATIONS ➤ InstallationEn 11
Example for installing the unit
This unit outputs sound beam as shown in the illustrations below. Install this unit where
there are no obstacles such as furniture obstructing the path of sound beams.
Otherwise, the desired surround sound effects may not be achieved.
You may install this unit in parallel with the wall or in the corner.
Parallel installation
Install this unit in the exact center of the wall when it is measured from the left and right
corners.
Corner installation
Install this unit in the corner at a 40° to 50° angle from the adjacent walls.
Parallel installation (with 5 Beam)
Objects, such as
furniture
Corner installation (with Stereo + 3 Beam)
40° to 50°
Parallel installation
Install this unit as close to the exact center of the wall as possible.
Ideal installation condition
Install this unit as close to the exact front of your normal listening position as possible.
The distance between listening position and the unit should be more than 1.8 m (6 ft).
Objects, such as
furniture
More
than
1.8 m
(6 ft)
More than
1.8 m (6 ft)
PREPARATIONS ➤ InstallationEn 12
Installing in a non-square room
Install this unit so that the sound beams can be reflected off the walls.
Irregularly shaped rooms with solid walls on all sides
Irregularly shaped rooms that are open to a hallway on one side
• If this unit cannot be repositioned, or the listening position cannot be changed, the optional YRB-100 sound
reflection board may be installed for a better surround sound experience (p. 73).
PREPARATIONS ➤ InstallationEn 13
Example for installing the unit in living room
• As sound beams normally pass through tables, tables are not obstacles. And a
cupboard installed facing the wall reflects sounds.
• In a case of the listening room as shown in the illustration below, adjusting the position
of the right channel after AUTO SETUP (p. 32) enables to achieve more desired
surround sound effects (p. 55).
• As the curtains absorb sounds, the sound features of the listening room is different
from the case with the curtain opened and the case with the curtain closed. Using
saving settings function enables to save the best settings for each case of listening
room (p. 47).
Objects, such as
furniture
Unrecommended listening environments
This unit creates surround sound by reflecting projected sound beams off the walls of
your listening room. The surround sound effects produced by this unit may not be
sufficient when this unit is installed in the following locations.
• Rooms with walls inadequate for reflecting sound beams
• Rooms with acoustically absorbent walls
• Rooms with measurements outside the following range:
W (3 to 7 m (10 to 23 ft)) × H (2 to 3.5 m (7 to 11.5 ft)) ×
D (3 to 7 m (10 to 23 ft))
• Rooms where objects such as furniture are likely to obstruct the path of sound beams
• Rooms with less than 1.8 m (6 ft) from the listening position to this unit
• Rooms where the listening position is close to the walls
• Rooms where the listening position is not in front of this unit
Enjoying surround effects regardless of conditions (My
Surround)
The My Surround function creates rich surround sound effects in rooms with less than
optimal surround sound conditions. See “Switching between audio output methods for
surround playback” (p. 42, 43) for more information.
PREPARATIONS ➤ InstallationEn 14
If the TV remote control does not work properly after
the center unit is installed (TV Remote Repeater
function)
When the TV Remote Repeater function is enabled, the unit receives TV remote control
signals at the TV remote control sensor (on front) and transmits the signals from the TV
Remote Repeater (on rear). This function is useful when you cannot operate your TV
from the remote control because the remote control sensor of the TV is blocked by the
unit.
• This function can be used while the TV remote control is using infrared signals.
TV remote control sensor
TV remote control
SYSTEM
SUBWOOFER
RL
AUX2 TV OPTICAL
CONNECTOR
OUT
AUX1
OUT (ARC) IN1 IN2
HDMI
IN3
TV Remote Repeater
Turn on the unit.
1
Hold down the REPEATER key on the supplied remote control for
2
more than 3 seconds to enable the TV Remote Repeater function.
The REPEATER indicator on the front panel display will glow.
Disabling the TV Remote Repeater function
Hold down the REPEATER key on the supplied remote control for more than 3 seconds.
PREPARATIONS ➤ InstallationEn 15
Adjusting the height of the center unit
Turn the legs counter-clockwise to increase the height of the center unit if necessary.
Use the arrows (
of these legs, to confirm that the legs are positioned at the same height.
❑ Removing the legs
If the center unit obstructs the remote control sensor on the TV or signal transmitter for
3D glasses, remove the legs to decrease the height of the center unit.
The legs consist of components (inner legs) that are fixed to the center unit with screws,
and components (outer legs) that can be removed by rotating them.
Remove the outer legs.
1
Keep turning the outer legs counter-clockwise to remove them.
U) on the bottom of the left and right legs, and the scale on the insides
Adjustable range:
22 to 35 mm
(7/8 to 1-3/8 in)
Scale
Remove the inner legs.
2
Use a screwdriver to remove the screws.
Attach the one of the four supplied non-skid pads at each of the four
3
corners on the bottom of the center unit.
An example of pad positioning is shown in the illustration below.
• Store the legs and screws in a safe place out of the reach of children for later use and to prevent children
from accidentally swallowing screws.
PREPARATIONS ➤ InstallationEn 16
❑ Attaching the legs
Attach the innter legs.
1
Position the inner legs so that the arrow (U) on them points toward the rear
side, and insert the protrusions into the slots on the center unit.
Rear side
Use a screwdriver to tighten the screws and lock the inner legs in place.
Attach the outer legs.
2
Position the outer legs so that the arrow (U) on them points towards the rear
side, and turn them clockwise to attach them.
PREPARATIONS ➤ InstallationEn 17
Positioning the subwoofer on its side
The subwoofer can be laid on its side when positioned on a rack.
Remove the legs and washers attached to the bottom of the
1
subwoofer.
Use a screwdriver to remove screws.
Leg
Washer
• Store the legs, screws, and washers in a safe place out of the reach of children for later use and to
prevent children from accidentally swallowing screws or washers.
Place the subwoofer on its side as shown in the illustration, and
2
attach each of the four supplied pads at each of the four corners.
Position the subwoofer as shown in the illustration.
3
PREPARATIONS ➤ InstallationEn 18
Mounting the center unit on a wall
If your TV is mounted on a wall, the optional Wall Mount Bracket SPM-K20 can be used
to mount this unit on the wall under the TV.
See “Dimensions” (p. 22) for this unit and SPM-K20 dimensions.
• Be sure to read “SAFETY INSTRUCTIONS” in the Installation Manual supplied with the SPM-K20 before
mounting it.
• The template and screws supplied with the SPM-K20 are not used with this unit.
• SPM-K20 may not be available in some countries or regions.
• Space between this unit and the wall is limited. Therefore, use of a flexible HDMI cable, or right-angle
connector, (neither supplied) is strongly recommended.
Flexible HDMI cable or
right-angle connector
❑ Mounting the SPM-K20
Be sure that there is enough space on the wall to mount the wall mount bracket and this
unit. Follow the instructions below to mount both.
Attach the three supplied pads to the wall mount bracket as shown in
1
the illustration.
YSP-CU2500
SPM-K20
10.8 mm
28 mm
Follow instructions provided from this page through page 22.
PREPARATIONS ➤ InstallationEn 19
Attach the template supplied with this unit to the wall and use a thumbtack or pin to mark the position where screws will be inserted in the wall.
2
Template
Attach the template to the wall so that the center of
the template is aligned with the center of the TV.
Mount the wall mount bracket on the wall.
3
Screw self-tapping screws (not supplied) partway
into the wall where marked using the template.
The wall mount bracket is designed to be offset
slightly to the right of the center of this unit.
Mount the wall mount bracket on these
screws, and then tighten the screws.
Once screw position has been
marked, remove the template.
Screw self-tapping screws, at least six including the
two previously used, into as many holes around the
outer edges of the wall mount bracket as possible to
ensure sufficient strength.
PREPARATIONS ➤ InstallationEn 20
• Be sure that screws are inserted in a sturdy portion of the wall or pillar. Do not mount the bracket on a wall
made of materials such as mortar or veneer, which may chip or peel. If screws fall out, the wall mount
bracket will also fall, resulting in damage or injury.
25 mm or more
25 mm or more
Connect commercial cables to this unit.
5
Flexible HDMI cable or
right-angle connector
Beam, etc.
Drywall
Attach the spacer supplied with this unit to the bottom of this unit
4
Beam, etc.
using the screws also supplied with this unit.
Screw
Spacer
Do not tighten the screws until this unit has been mounted on the wall mount
bracket.
Mount this unit on the wall.
6
Insert the screws on this unit into the mounting holes on the left and right sides
of the wall mount bracket, and then slide this unit to the left.
• When mounting or removing it, hold this unit firmly with both hands. If this unit falls, damage or injury
could occur.
PREPARATIONS ➤ InstallationEn 21
Tighten screws.
7
❑ Dimensions
YSP-CU2500
SPM-K20
10.8
28
125
154.3
(mm)
944
Tighten the screws used to attach the spacer to this unit in step 4.
143
153.8
298.3
276.8
10.8
457
500
YSP-CU2500SPM-K20
16.7
(1.4 kg)
PREPARATIONS ➤ InstallationEn 22
5
125
33.5
13.5
188.3
166.8
51
54
(mm)
(mm)
Preparing remote control
Before installing batteries or using the remote control, be sure to read battery and remote control precautions in “Safety Brochure” (separate booklet).
Installing the batteries
Press down on the arrow
and slide the cover in the
direction in which it
points.
Battery × 2
(AAA, R03, UM-4)
Slide the cover back to close it.
Operation range
STATUS
Within 6 m (20 ft)
PREPARATIONS ➤ InstallationEn 23
Connections
When external devices such as a TV, BD/DVD player, and/or game console are connected, audio and video signals are transmitted as shown below.
See pages 25 through 29 for instructions on connecting each device.
Audio connection
This unit: Plays audio from TV broadcasts, BD/DVD discs, etc.
Video connection
Audio and video
connection
STATUS
Optical cable
Use to connect a TV that does not
support audio return channel (ARC)
to this unit (p. 25).
PHONES INTELLIBEAM MIC
HDMI cable
Audio from TV broadcast
HDMI cableHDMI cable
BD/DVD player
Game console (HDMI-compatible)Satellite and cable TV tuner
Optical cable
(not HDMI-compatible)
• Do not connect the power cable until all connections are completed.
• Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/or jack.
Video cable
TV: Plays video from TV
broadcasts, BD/DVD player, etc.
PREPARATIONS ➤ ConnectionsEn 24
Connecting a TV
Connect a TV to the unit so that video input to the unit can be output to the TV. You can also enjoy playback of TV audio on the unit.
• Use a 19-pin HDMI cable with the HDMI logo printed on it. A cable with a maximum length of 5 m is recommended to prevent degradation of signal quality.
• For playback of 3D and 4K video content, use a high-speed HDMI cable.
TVs that support Audio Return Channel (ARC)
Connect the TV to the unit with an HDMI cable (not supplied).
Center unit (rear)
SYSTEM
SUBWOOFER
RL
CONNECTOR
AUX2 TV OPTICAL
OUT
AUX1
When connecting a TV that supports Audio Return Channel (ARC), activate the HDMI
control function (p. 59).
Audio Return Channel (ARC)
ARC enables input and output of audio signals via a single HDMI cable. If the TV supports ARC, audio
signals from the TV can be input to this unit via the same HDMI cable used to output video signals from
this unit to the TV.
• Use an ARC-compatible HDMI cable.
HDMI OUT (ARC) jackHDMI input
HDMI
HDMI
OUT (ARC) IN1IN2
OUT (ARC)
HDMIHDMI
IN3
(ARC)
TV
TVs that do not support Audio Return Channel (ARC)
Connect the TV to the unit with an HDMI cable (not supplied) and an optical cable.
Center unit (rear)
SYSTEM
SUBWOOFER
RL
AUX2 TV OPTICAL
CONNECTOR
OUT
AUX1
TV jack
1. Remove the cap2. Check the direction of
• TVs not equipped with an optical jack
Audio content from the TV can be input via the AUX2 coaxial digital or AUX1 analog jack. Set “TV INPUT”
in the setup menu to “COAXIAL [AUX2]” or “ANALOG [AUX1]” accordingly (p. 60).
HDMI OUT (ARC) jackHDMI input
HDMI
OUT (ARC) IN1IN2
OUT (ARC)
TV
HDMIHDMI
IN3
OO
OPTICAL
Audio output
(digital optical)
the plug
HDMI
TV
PREPARATIONS ➤ ConnectionsEn 25
Loading...
+ 58 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.