Yamaha YSP-1100 User Manual
OYAMAHA
YSP-llOO
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
OUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power supply cable from being walked on or
pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over,
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
I En
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by YAMAHA may
void your authority, granted by the FCC, to use the product.
2. IMPORTANT:
When connecting this product to accessories and/or another
product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use of
this product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact YAMAHA Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by YAMAHA Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying
blaring or distortion ~ and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries
Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.
II En
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place with at least 5 cm of space above (or below) this unit away from direct sunlight, heat sources, vibration, dust, moisture,
and/or cold.
3 Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
- Other components, as they may cause damage and/or
discoloration on the surface of this unit.
- Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
- Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
7 Do not plug in this unit to a wall outlet until all connections are
complete.
8 Do not operate this unit upside-down. It may overheat, possibly
causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of this
unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cable
disconnected from a wall outlet or this unit during a lightning
storm.
14 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed.
The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
17 Before moving this unit, press STANDBY/ON to set this unit in
standby mode, and disconnect the AC power plug from the wall
outlet.
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave the unit alone.
19 When using the unit for a long time, the unit may become warm.
Turn the power off, then leave the unit alone for cooling.
20 Install this unit near the AC outlet and where the AC power plug
can be reached easily.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
WARNING
THE POWER SUPPLY CABLE OF THIS UNIT MUST BE
CONNECTED TO THE MAIN SOCKET OUTLET VIA A
PROTECTIVE EARTHING CONNECTION.
This unit is not disconnected from the AC power source as long
as it is connected to the AC wall outlet, even if this unit itself is
turned off. This state is called the standby mode. In this state,
this unit is designed to consume a very small quantity of power.
IMPORTANT
Please record the serial number of this unit in the space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain this
Owner’s Manual in a safe place for future reference.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with Canadian ICES-
003.
FOR U.K. CUSTOMERS
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below. Note that the plug severed from
the mains lead must be destroyed, as a plug with bared
flexible cord is hazardous if engaged in a live socket outlet.
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE;
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED. Make sure that neither core is connected to the
earth terminal of the three pin plug.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Ill En
CONTENTS
INTRODUCTION
OVERVIEW...........................................................2
FEATURES............................................................3
USING THIS MANUAL.......................................4
SUPPLIED ACCESSORIES
CONTROLS AND FUNCTIONS
Front panel......................................................................6
Front panel display
Rear panel.......................................................................8
Remote control
.........................................................
...............................................................
................................
........................
PREPARATI
INSTALLATION
Before installing this unit.............................................11
Installing this unit.........................................................11
CONNECTIONS
Connecting a TV
Connecting a DVD player/recorder
Connecting a VCR........................................................18
Connecting a digital satellite tuner or
a cable TV tuner.......................................................19
Connecting a digital airwave tuner
Connecting other external components........................21
Connecting a subwoofer...............................................22
Connecting the power supply cable
About the RS-232C/REMOTE IN/IR-OUT
terminals...................................................................23
.................................................
.................................................
..........................................................
.............................
..............................
.............................
SETUP
GETTING STARTED
Installing batteries in the remote control......................24
Operation range of the remote control
Using the remote control..............................................25
Turning on the power
USING SET MENU.............................................26
Displaying the OSD......................................................26
The flow chart of SET MENU
CHANGING OSD LANGUAGE
AUTO SETUP (IntelliBeam)
The flow chart of AUTO SETUP
Installing the optimizer microphone
Using AUTO SETUP (IntelliBeam)
USING THE SYSTEM MEMORY
Convenient usage of the system memory
Saving settings..............................................................36
Loading settings
........................................
.........................
...................................................
.....................................
.......................
..............................
................................
............................
............................
...................
....................
...........................................................
15
24
28
29
36
Stereo plus 3 beam........................................................43
3 beam...........................................................................43
Enjoying 2-channel sources
in surround sound.....................................................45
Adjusting surround mode parameters
5
6
7
9
II
ENJOYING STEREO SOUND..........................47
Stereo playback
............................................................
PLAYING BACK SOUND CLEARLY
(My beam).........................................................48
Using auto-adjust function
Using manual-adjust function
...........................................
USING SOUND FIELD PROGRAMS
What is a sound field?...................................................50
Sound field program descriptions
Turning on CINEMA DSP programs...........................52
Turning off CINEMA DSP programs
Adjusting CINEMA DSP effect levels.........................54
..........................
......................................
..............
................................
..........................
46
47
48
49
50
51
54
USING THE VOLUME MODE
(Night listening mode/TV volume
16
17
equal mode)
USING BASS SOUND ENHANCER
(TruBass)
......................................................
..........................................................
55
57
USING THE SLEEP TIMER.............................58
Setting the sleep timer
20
23
Canceling the sleep timer
ADVANCED OPERATION
..................................................
.............................................
58
59
MANUAL SETUP................................................60
Using MANUAL SETUP
BEAM MENU..............................................................62
SOUND MENU............................................................66
INPUT MENU..............................................................68
DISPLAY MENU.........................................................70
ADJUSTING THE AUDIO BALANCE
24
25
Using the test tone
Using the audio output being player back
SELECTING THE INPUT MODE
ADJUSTING SYSTEM PARAMETERS
27
29
30
31
36
37
Using the system parameters
Setting the MEMORY PROTECT...............................76
Setting the MAX VOLUME
Setting the TURN ON VOLUME................................78
Setting the DEMO MODE
Setting the FACTORY PRESET..................................79
REMOTE CONTROL FEATURES
Setting remote control codes........................................81
Controlling other components
Using the TV macro
............................................
...........
........................................................
....................
...................
.........
........................................
........................................
...........................................
.................
......................................
.....................................................
61
72
75
76
81
72
73
76
77
78
I I
82
84
BASIC OPERATION
PLAYBACK.........................................................39
Selecting the input source
Playing back sources
Adjusting the volume...................................................41
Muting the sound
ENJOYING SURROUND SOUND
5 beam...........................................................................42
............................................
....................................................
.........................................................
...................
42
ADDITIONAL INFORMATION
TROUBLESHOOTING......................................86
39
40
Audio formats...............................................................89
Audio information
GLOSSARY
.........................................................
........................................................
89
89
INDEX...................................................................90
41
SPECIFICATIONS
.............................................
91
1 En
OVERVIEW
It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of
wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of
surround sound experience as your local movie theater.
YAMAHA YSP-1100 Digital Sound Projector challenges this preconception that complicated speaker setup and
troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.
This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is
not only easy to set up, but which is also capable of reproducing the kind of powerful surround sound you have been
waiting for from its built-in 2 woofers and 40 full-range small speakers.
You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly
directional sound that comes in on the listening position from all directions.
The YSP-1100 projects sound beams containing surround sound information for the front right (R), front left (L),
surround right (SR) and surround left (SL) speaker positions, which are reflected off the walls of your listening room
before reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector
creates true-to-life 5.1 channel surround sound that makes you feel as if there are actual speakers around the room.
Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.
Imaginary
front right
speaker
2 En
Imaginary
front left
speaker
Imaginary
center
speaker
Imaginary
surround right
speaker
Listening position
Imaginary
surround left
speaker
FEATURES
Digital Sound Projector
This unit employs the digital sound projector technology
that allows one slim unit to control and steer multiple
channels of sound to generate multi channel surround
sound, thus eliminating the need for satellite loudspeakers
and cabling normally associated with conventional
surround sound systems. This unit is also equipped with
the following beam modes so that you can enjoy the
surround sound.
♦ 5 beam
♦ Stereo plus 3 beam
♦ 3 beam
This unit also employs the stereo playback and my beam.
My beam
This unit employs the my beam so that you can achieve a
clear sound in noisy environment. You can adjust the
beam angle manually or automatically using the supplied
remote control.
Cinema DSP Digital
This unit employs the Cinema DSP Digital technology
developed by YAMAHA Electronics Coip. so that you can
experience movies at home with all the dramatic sound
impact that the director intended to convey.
Versatile Remote Control
The supplied remote control come with preset remote
control codes to be used to control the DVD player, VCR,
cable TV tuner and digital satellite tuner connected to this
unit. In addition, the remote control is equipped with the
macro capability so that you can perform a series of
operations with the press of a single button.
AUTO SETUP (IntelliBeam)
This unit employs the automatic sound beam and acoustic
optimization technology with the aid of the supplied
optimizer microphone so that you can avoid troublesome
listening-based speaker setup and achieve highly accurate
sound beam adjustments that best match your listening
environment.
Compatibility with the Newest Technologies
This unit employs decoders compatible with Dolby
Digital, DTS (Digital Theater Systems), Dolby Pro Logic,
Dolby Pro Logic II and DTS Neo:6.
♦ Dolby Digital
This is the standard audio signal format used on DVDs and
other purely digital media. This surround technology deliver
high-quality digital audio for up to 5.1 discrete channels to
produce a directional and more realistic effect.
♦ DTS (Digital Theater Systems)
This is an audio signal format used on DVDs and other purely
digital media. This surround technology deliver high-quality
digital audio for up to 5.1 discrete channels to produce a
directional and more realistic effect.
♦ Dolby Pro Logic
This sophisticated, matrix decoding technology up-converts
any 2 channel source audio to a 5.1 channel full bandwidth
playback, resulting in a surround sound experience.
♦ Dolby Pro Logic II
This is fundamentally a redesigned version of Dolby Pro
Logic that employs 2 stereo surround channels, a subwoofer
and a greatly enhanced steering logic. As a result, this
improved technology provides an exceptionally stable sound
field that simulates 5.1 to a much greater degree than the
original Dolby Pro Logic. In addition, Dolby Pro Logic II
features Movie, Music and Game modes specifically designed
for movies, music and games respectively.
♦ DTSNeo:6
This technology decodes the conventional 2 channel sources
for 6 channel playback, enabling playback with the full-range
channels with higher separation. Music mode and Cinema
mode are available to play back music and movie sources
respectively.
lnte\l/Beam
The “lnte\l/Beam ” logo and ‘TntelliBeam” are trademarks of
YAMAHA Corporation.
[CINEM
trademarks of YAMAHA Corporation.
nniDOLBYl
DIGITAL
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
^2^ ” logo and “Cinema DSP” are registeredThe“
E2t
“DTS” and “Neo:6” are trademarks of Digital Theater Systems,
Inc.
Manufactured under license from 1 Ltd. Worldwide patents
applied for.
The “ I'-- ” logo and “Digital Sound Projector™” are trademarks
of 1 Ltd.
SRScmj
TruBass
TruBass, SRS and the “ C#) ” symbol are registered trademarks
of SRS Labs, Inc. TruBass technology is incorporated under
license from SRS Labs, Inc.
3 En
USING THIS MANUAL
Notes
• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the
supplied owner’s manual for the component.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In such cases, the operation is
described using remote control operation.
• indicates a tip for your operation.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and product, the product has priority.
1 Install this unit In your listening room.
See “INSTALLATION” on page 11.
2 Connect this unit to your TV and other external components.
See “CONNECTIONS” on page 15.
3 Prepare the remote control and turn on the power of this unit.
See “GETTING STARTED” on page 24.
4 Run AUTO SETUP.
See “AUTO SETUP (IntelliBeam)” on page 29.
5 Play back a source.
See “PLAYBACK” on page 39.
6 Change the beam modes and/or CINEMA DSP settings.
See “ENJOYING SURROUND SOUND” on page 42.
If you want to make additional settings
and adjustments
7 Run MANUAL SETUP to fine-tune settings and/or set remote control codes.
See “MANUAL SETUP” on page 60 and “REMOTE CONTROL FEATURES” on page 81.
4 En
SUPPLIED ACCESSORIES
Check that you have received all of the following parts.
Remote control (x1)
STANDBY/ON POWER POWER
(^) o
ysTBj lIvcRl IÎd^I HauxI
IMPUTI INPUT2 MACRO
VOL MODE SEtÌjP INPUTMODE SLEEP
l[E) o o o
a a a a
5BEAM ST^BEAM 3BEAM
CD CD ŒD
STEREO MY BEAM SURROUND
QD CD CD
MUSIC MOVIE SPORTS
S CD CD
OFF c»:>
CD GD CD
CH LEVEL MENU
^YAMAHA
Batteries (x2)
(AA, R6, UM-3)
OSD video pin cable (x1)
(Yellow)
Optimizer microphone (x1)
Cable clamp (x1)
Optical cable (x1)
Digital audio pin cable (x1)
^
Cardboard microphone
stand (x1)
O
Power supply cable (x1)
5 En
Front pane!
CONTROLS AND FUNCTIONS
© OPTIMIZER MIC jack
Use to connect the supplied optimizer microphone to be
used to run AUTO SETUP (see page 30).
© Front panel display
Shows information about the operational status of this
unit.
@ Remote control sensor
Receives infrared signals from the remote control.
© INPUT
Press repeatedly to switch between input sources (TV,
STB, VCR, DVD or AUX). See page 39 for details.
Outputs a test tone to experience the sound beam (see
page 72).
® VOLUME-/+
Controls the volume level of all audio channels (see
page 41).
® STANDBY/ON
Turns on the power of this unit or sets it to the standby
mode (see page 25).
Nates
• When you turn on the power of this unit, you will hear a click
and there will be a 4 to 5-second delay before it can reproduce
sound.
• In the standby mode, this unit consumes a small amount of
power in order to receive infrared-signals from the remote
control.
6 En
Front panel display
(T) ®
CONTROLS AND FUNCTIONS
InightIÌìLeepI
■■■■■ ■■■■■ ■■■■■
■■■■■ ■■■■■ fliflii
■■■■■ iiiia ■■■■■
■■■■■ ■■■■! ■■■■■
■■■■■ ■■■■■ ■■■■■
■■■■■ ■■■■■ ■■■■■
■■■■■ ■■■■■ ■■■■■
[€ltg PCM □□DIGITAL □□PLi]
■■■■■ ■■■■■ ■■■■■
■■■■■ ■■■■■ ■■■■■
■■■■■ ■■■■■ ■!■■■
■ ■■■■ ■■■■■ ■■■■■
■ ■■■■ ■■■■■ ■■■■■
■■■■■ ■■■■■ ■■■■■
■ ■■■■ ■■■■■ ■■■■■
■■■■■ ■■■■■ ■■■■■ ■llfll ■■■■■ ■■■■■ ■■■■■ flllfll
■■■■■ ■■■■■ ■■■■■ !■■■■ ■■■■■ ■■■■■ ■■■■■ lina
aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa
aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa
aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa
aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa
aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa
© NIGHT indicator
Lights up when one of the night listening modes is
selected (see page 55).
© SLEEP indicator
Lights up when the sleep timer is turned on (see page 58).
© Decoder indicators
Light up when the corresponding decoder of this unit is in
operation (see page 44).
VOL
0 Volume level indicator
Shows the current volume level (see page 41).
0 Multi-information display
Shows information when you adjust the parameters of this
unit.
You can adjust the brightness of the front panel display using the
DISPLAY MENU parameters in MANUAL SETUP (see
page 70).
7 En
CONTROLS AND FUNCTIONS
Rear panel
© RS-232C/REMOTE IN terminals
These are control expansion terminals for factory use only
(see page 23).
© DVD COAXIAL DIGITAL IN jack
Use to connect a DVD player/recorder via a coaxial digital
connection (see page 17).
© AUX OPTICAL DIGITAL IN Jack
Use to connect an external component via an optical
digital connection (see page 21).
© TV/STB OPTICAL DIGITAL IN jack
Use to connect a TV, a digital satellite tuner or a cable TV
tuner via an optical digital connection (see pages 16, 19
and 20).
© TV/STB AUDIO IN jacks
Use to connect a TV, a digital satellite tuner or a cable TV
tuner via an analog audio connection (see pages 16, 19
and 20).
® VCR AUDIO IN jacks
Use to connect a VCR via an analog audio connection
(see pages 17 and 18).
© SUBWOOFER jack
Use to connect a subwoofer (see page 22).
© VCR VIDEO IN jack
Use to connect a VCR via a composite analog video
connection (see page 18).
® DVD/AUX VIDEO IN jack
Use to connect a DVD player/recorder or an external
component via a composite analog video connection
(see page 17).
® DVD/AUX COMPONENT VIDEO IN jacks
Use to connect a DVD player/recorder or an external
component via a component analog video connection
(see page 17).
® STB VIDEO IN jack
Use to connect a digital satellite tuner or a cable TV tuner
via a composite analog video connection (see pages 19
and 20).
® STB COMPONENT VIDEO IN jacks
Use to connect a digital satellite tuner or a cable TV tuner
via a component analog video connection (see pages 19
and 20).
® VIDEO OUT jack
Use to connect to the video input jack of your TV via a
composite analog video connection to display the OSD of
this unit (see page 16).
® COMPONENT VIDEO OUT jacks
Use to connect to the video input jacks of your TV via a
component analog video connection to display the OSD of
this unit (see page 16).
® IR-OUT terminal
This is a control expansion terminal for factory use only
(see page 23).
® AC IN
Use to connect the supplied power supply cable
(see page 23).
8 En
Remote control
The functions of some buttons change depending on the
position of the operation mode selector ((g)). This section
basically describes the functions of the remote control
used to control this unit.
You can also control other components using the remote control
once you set the appropriate remote control codes. See
“Controlling other components” on page 82 for details.
(i>
CONTROLS AND FUNCTIONS
0
Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
(2) STANDBY/ON
Sets this system to the standby mode (see page 25).
(3) Transmission indicator
Lights up when infrared control signals are being output.
0
Input selector buttons
Use to select an input source (STB, VCR, DVD, AUX or TV).
Use to change the control area of the remote control. ((g):TV/AV)
® VOL MODE
Turns on or off the volume modes (see page 55).
® AUTO SETUP
Use to enter the AUTO SETUP menu (see page 29).
® Numeric buttons
Use to enter numbers. ((g):TV/AV)
® STEREO
Use the playback sources in 2-channel stereo (see
page 47).
® Sound field program buttons
Use to select sound field programs (see page 50).
® CH LEVEL
Adjusts the volume level of each channel (see page 73).
® Cursor buttons ^ / Yz / <] / |>, ENTER
Use to select and adjust SET MENU items.
Use to select DVD menu items. ((g):TV/AV)
© TEST
Outputs a test tone when adjusting the output level of each
speaker (see page 72).
® VOLUME+/-
Increases or decreases the volume level of this unit (see
page 41).
® MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level (see page 41).
© TV INPUT
Switches the input source or the TV (see page 82).
® DVD playerA^CR control buttons
Use to control the DVD player or the VCR (see pages 82
and 83).
© My beam microphone
Use to collect the test tones from this unit when using the
my beam auto-adjust function (see page 48).
9 En
CONTROLS AND FUNCTIONS
® TV POWER
Turns on the power of the TV or sets it to the standby
mode (see page 82).
® AV POWER
Turns on the power of the selected component or sets it to
the standby mode (see pages 82 and 83).
@ INPUT1/INPUT2
Selects the input source of the TV (see page 82).
(g) MACRO
Use to set the TV macro (see page 84).
® SLEEP
Sets the sleep timer (see page 58).
@ INPUTMODE
Switches between input modes (AUTO, DTS or
ANALOG). See page 75 for details.
(g) Beam mode buttons
Change the beam mode settings (see pages 42, 47 and 48).
@ SURROUND
Selects the surround mode for playback (see page 42).
(g) MY BEAM
Use to select the my beam as the beam mode (see
page 48).
@ TruBass
Use to effectively reproduce the bass sound (see page 57).
@) MENU
Displays the setup menu on your TV monitor (see
pages 31 and 61).
Display the DVD menu. (@):TV/AV)
(g Operation mode selector
Selects the operation mode of this unit. Select YSP when
operating this unit and select TV/AV when operating the
TV or other AV components set up the appropriate remote
control codes.
@ RETURN
Use to select sleep timer settings or return to the previous
SET MENU screen.
Use to return to the previous DVD menu screen or exit the
DVD menu. (g;TV/AV)
(g) TVVOL+/-
Adjusts the volume level of the TV (see page 82).
® CH+/-
Switches between channels of the TV or the VCR (see
pages 82 and 83).
® TV MUTE, CODE SET
Mutes the audio output of the TV (see page 82).
Use to set up remote control codes (see page 81).
10 En
INSTALLATION
This section describes a suitable installation location to install the unit using a metal wall bracket, a rack or a stand.
Before installing this unit Installing this unit
This unit creates surround sound by reflecting projected
sound beams off the walls of your listening room. The
surround sound effects produced by this unit may not be
sufficient when the unit is installed in the following
locations.
• Rooms with surfaces inadequate for reflecting sound
beams
• Rooms with acoustically absorbent surfaces
• Rooms with measurements outside the following range
W (3 to 7 m) X H (2 to 3.5 m) x D (3 to 7 m)
• Rooms with less than 1.8 m from the listening position
to the speaker positions
• Rooms where objects such as furniture are likely to
obstruct the path of sound beams
• Rooms where the listening position is close to the walls
• Rooms where the listening position is not in front of
this unit
Make sure you leave an adequate amount of ventilation
space so that heat can escape. Make at least 5 cm of space
above or below this unit.
Side view
5 cm or more
Install this unit where there are no obstacles such as
furniture obstructing the path of sound beams. Otherwise,
the desired surround sound effects may not be achieved.
You may install this unit in parallel with the wall or in the
comer.
Parallel installation
Install this unit in the exact center of the wall when it is
measured from the left and right comers.
An object, such as furniture
Corner installation
Install this unit in the comer at a 40° to 50° angle from the
adjacent walls.
40° to 50°
Front
Rear
Side
Notes
• We do not recommend installing this unit so that it is positioned
directly on the floor of your listening room. Please install this
unit using a metal wall bracket, rack or stand.
• This unit weighs 9.0 kg. Be sure to install this unit where it will
not fall subject to vibrations, such as from an earthquake, and
where it is out of the reach of children.
• When using a cathode-ray tube (CRT) TV, do not install this
unit directly above your TV.
• This unit is shielded against magnetic rays. However, if the
picture on your TV screen becomes blurred or distorted, we
recommend moving the speakers away from your TV.
An object, such as furniture
11 En
INSTALLATION
■ Installation examples
Example 1
Install this unit as close to the exact center of the wall as possible.
Example 2
Install this unit so that the sound beams can be reflected off the walls.
Example 3
Install this unit as close to the exact front of your normal listening position.
12 En
INSTALLATION
■ Using a metal wall bracket
You can use the optional metal wall bracket to mount this
unit on the wall in your listening room.
Metal wall bracket
This unit
TV
Refer to the instructions supplied with the metal bracket for
details on how to attach the metal bracket to the wall or how to
attach this unit to the metal bracket.
■ Using a stand
You can mount your TV on the stand placed on a
commercially available rack to install this unit under your
TV.
stand
■ Using a TV stand
You can use the optional TV stand to install this unit. For
detailed information on installing this unit using a TV
stand, refer to the installation manual supplied with the
optional TV stand.
TV
This unit
3
This unit
Refer to the instructions supplied with the stand for details on
how to install the stand or how to mount this unit and the TV on
the stand.
■ Using a rack
You can install this unit either above or under your TV in a
commercially available rack.
When this unit is instaiied above your TV
When this unit is installed under your TV
Note
Make sure that the rack is large enough to allow adequate
ventilation space around this unit (see page 11) and that it is
strong enough to support the weight of both this unit and your TV.
13 En
INSTALLATION
■ Affixing this unit
Peel off the film from each of the four supplied fasteners
and then secure them to the bottom four comers of this
unit and the top of the rack, etc.
This unit
Notes
• Do not install this unit on top of a slanted surface. This unit may
fall over and cause injury.
• Make sure you wipe the surface of the rack, etc. before securing
the fasteners. Applying the tape to a dirty or wet surface will
weaken the sticking power of the tape, and this unit may fall as
a result.
14 £n
CONNECTIONS
This unit is equipped with the following types of audio/video input/output jacks:
For audio input For video input
• 2 optical digital input jacks • 3 composite analog input jacks
• 1 coaxial digital input jack • 2 sets of component analog input jacks
• 2 sets of analog input jacks For video output
• 1 composite analog output jack
• 1 set of component analog output jacks
Use these audio/video input/output jacks to connect external components such as your TV, DVD player, VCR, digital
satellite tuner, cable TV tuner and game console. Further, by connecting a subwoofer to this unit, you can enjoy
reinforced low bass sounds. For details on how to connect various types of external components to this unit, see pages 16
to 22.
CAUTION
Do not connect this unit or other components to the main power until all connections between components are complete.
Audio connection
Video connection
TV
To prevent cables from becoming unplugged, place the supplied
cable clamp with the open side facing upward, attach it to the rear
panel of this unit in a suitable position and then affix cables in the
cable clamp.
Optical fiber cable
15 £n
CONNECTIONS
Conneeting a TV
Connect a TV to this unit and display the OSD for easy viewing when you adjust the system parameters in SET MENU.
■ Audio connections
Connect the analog audio output jacks of your TV to the
TV/STB AUDIO IN jacks of this unit. If your TV has an
optical digital output jack, connect the optical digital
output jack of your TV to the TV/STB OPTICAL
DIGITAL IN jack of this unit in addition to the analog
audio connection. Once the digital audio connection is
made, digital audio signals can be input to this unit during
■ Video connections
Connect the video input jacks of your TV to the VIDEO
OUT jacks of this unit. If your TV has component video
input jacks, connect the component video input jacks of
your TV to the COMPONENT VIDEO OUT jacks of this
unit in addition to the composite video connection. Once
the component video connection is made, you can enjoy
images with better resolution.
digital broadcasting.
• The circuits of composite and component video signals are independent of each other.
• To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 15).
Note
If you connect this unit to the analog audio and optical digital audio output jacks at the same time as shown in the left illustration below,
the digital audio signals output at the optical digital output jack take priority over the analog audio signals output at the analog audio
output jacks.
TV
Cables used for audio connections
Audio pin cable (supplied)
(White) f-CtQZ
(Red) (Red)
Optical cable (supplied)
^^81 {(
16
^ (White)
Cables used for video connections
(Yellow)
......................................
Component video pin cable
(Green) c^DIIDIh^
( ^
....................M-......
(Red) czQOg-J
Video pin cable (supplied)
Jill 1 ц
^ 1 ))
\\
—(Yellow)
(Green)
Connecting a DVD player/recotder
Connect a DVD player/recorder and enjoy DVDs.
CONNECTIONS
■ Audio connections
Connect the optical digital output jack of your DVD
player/recorder to the DVD COAXIAL DIGITAL IN jack
of this unit. In case you connect this unit to a DVD/VCR
combo player/recorder, connect the analog audio output
jacks of your DVD/VCR combo player/recorder to the
VCR AUDIO IN jacks of this unit in addition to the
optical digital audio connection.
To prevent the potical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 15).
■ Video connections
Connect the video output jack of your DVD player/
recorder to the DVD/AUX VIDEO IN jack of this unit. If
your DVD player/recorder has component video output
jacks, connect the component video output jacks of your
DVD player/recorder to the DVD/AUX COMPONENT
VIDEO IN jacks of this unit. Once the component video
connection is made, you can enjoy images with better
resolution.
Notes
• Check that your DVD player/recorder is properly set to output Dolby Digital and DTS digital audio signals. If not, adjust the system
settings of your DVD player/recorder. For details, refer to the operation manual supplied with your DVD player/recorder.
• If your DVD player/recorder does not have a coaxial digital output jack, make an optical digital audio connection instead
(see page 21).
Cables used for audio connections
Audio pin cable
(White)
(Red)
Digital audio pin cable (supplied)
(Orange)
ih
(White)
(Red)
(Orange)
Cables used for video connections
Video pin cable
Component video pin cable
(Green)
.......
|||
......
iHj
(Blue) czl' Mlii-l—j^
(Red) cNQKIM
(Green)
MhIIIII ■ N (Blue)
LlJI Hi y (Red)
17 £n
CONNECTIONS
Connecting a VCR
Connect a VCR and enjoy video cassette tapes.
■ Audio connections ■ Video connections
Connect the analog audio output jacks of your VCR to the Connect the video output jack of your VCR to the VCR
VCR AUDIO IN jacks of this unit. VIDEO IN jack of this unit.
Nate
Be sure to match the left and right output jacks of your VCR with the left and right input jacks of this unit.
VCR
Analog audio
output
<
R L
# ©
Video
output
•
k
1 1
Cables used for audio connections
Audio pin cable
18 £n
Cables used for video connections
Video pin cable
(Yellow)
(Yellow)
Connecting a digital satellite tuner or a catie TV tuner
CONNECTIONS
Connect a digital satellite tuner or a cable TV tuner and enjoy
■ Audio connections
Connect the optical digital output jack of your digital
satellite tuner or cable TV tuner to the TV/STB OPTICAL
DIGITAL IN jack of this unit. Connect the analog audio
output jacks of your digital satellite tuner or cable TV
tuner to the TV/STB AUDIO IN jacks of this unit in
addition to the optical digital audio connection.
To prevent the potical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 15).
Digital satellite tuner
digital satellite broadcasting or cable TV broadcasting.
■ Video connections
Connect the video output jack of your digital satellite
tuner or cable TV tuner to the STB VIDEO IN jack of this
unit. If your digital satellite tuner or cable TV tuner has
component video output jacks, connect the component
video output jacks of your digital satellite tuner or cable
TV tuner to the STB COMPONENT VIDEO IN jacks of
this unit. Once the component video connection is made,
you can enjoy images with better resolution.
Cables used for audio connections
Audio pin cable
optical cable
Hi—
(White)
(Red)
Cables used for video connections
Video pin cable
Component video pin cable
(Green)
...............
(Blue) a 'lll-l—
(Red) cz| IB §
L-l llll M N (Red)
..
(Green)
19 En
CONNECTIONS
Connecting a digital airwave tuner
If your digital airwave tuner does not support analog broadcasting, make audio/video connections as shown below.
■ Audio connections
Connect the optical digital output jack of your digital
airwave tuner to the TV/STB OPTICAL DIGITAL IN jack
of this unit. Connect the TV/STB AUDIO IN jacks of this
unit to the analog audio output jacks of your TV in
addition to the optical digital audio connection between
your digital airwave tuner and this unit.
■ Video connections
Connect the video output jack of your digital airwave
tuner to the STB VIDEO IN jack of this unit. If your
digital airwave tuner has component video output jacks,
connect the component video output jacks of your digital
airwave tuner to the STB COMPONENT VIDEO IN jacks
of this unit. Once the component video connection is
made, you can enjoy images with better resolution.
To prevent the optical cable from being unplugged, afifix the optical cable in the supplied cable clamp (see page 15).
Digital airwave tuner
Optical digital
output
Video Component
output video output
-t—t-M-
Connect to the analog
audio output jacks of
the TV.
Rear panel of this unit
Note
You can only
make either a
composite or a
component video
connection.
DVD
COAXIAL
DIGITAL IN
Cables used for audio connections
Audio pin cable
Optical cable
20 En
AUX TV/STB
-----
OPTICAL
----
(White)
(Red)
Cables used for video connections
Video pin cable
(Yellow)
Component video pin cable
(Green)
(Blue)
(Red)
¡h
ЧЕЖ> (R^d)
..
(Green)
(Yellow)
(Blue)
CONNECTIONS
Connecting other external components
To connect other external components, connect the optical digital output jack of an external component to the AUX
OPTICAL DIGITAL IN jack of this unit. Use this connection method to connect an external component that supports an
optical digital connection or to connect a DVD player/recorder via an optical digital connection.
\ >/
-ii)l
To prevent the optical cable from being unplugged, afifix the optical cable in the supplied cable clamp (see page 15).
Hote
If you connect a DVD player/recorder via a coaxial digital connection, adjust settings for INPUT ASSIGNMENT (see page 68).
CD player, etc.
Cables used for connections
optical cable
21 En
CONNECTIONS
Connecting a subwoofer
To connect a subwoofer, connect the monaural input jack of your subwoofer to the SUBWOOFER jack of this unit.
If a subwoofer is connected to this unit, turn on the power of your subwoofer and then run AUTO SETUP (see page 29)
or select SWFR for BASS OUT in SUBWOOFER SET (see page 67).
22 En
Subwoofer pin cable
CONNECTIONS
Connecting the power supply cable
Once all other connections are complete, plug one end of the power supply cable into the AC IN terminal of this unit and
then plug the other end into the AC wall outlet.
To the AC outlet
f
1
ogogogogogogogogo
ogogogogogogogogo
About the RS-232C/REM0TEIN/IR-OUT terminals
The RS-232C, REMOTE IN and IR-OUT terminals do not support normal external component connections. These are
control expansion terminals for factory use only.
RS-232C terminal REMOTE IN terminal
____
I
o
I H H
X DVD TV/STB
COAXIAL —OPTICAL—
— DIGITAL INPUT
----
23 En
GETTING STARTED
Installing batteries in the remote control
1 Press and hold the ^ mark on the battery
cover and then slide off the cover.
2 Insert the two supplied batteries (AA, R6,
UM-3) into the battery compartment.
Make sure you insert the batteries according to the
polarity markings (+/-).
Remove the transparent sheet before using the remote control.
Operation range of the remote control
The remote control transmits a directional infrared beam.
Use the remote control within 6 m of this unit and point it
toward the remote control sensor on this unit during
operation.
3 Close the battery cover.
Notes
• Change all of the batteries if you notice the following
conditions; the operation range of the remote control decreases,
the indicator does not blink or its light becomes dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• Exhausted batteries may leak. If the batteries have leaked,
dispose of them immediately. Avoid touching the leaked
material or letting it come into contact with clothing, etc. Clean
the battery compartment thoroughly before installing new
batteries.
• Do not throw away batteries with general house waste. Dispose
of them correctly in accordance with your local regulations.
• The contents of the memory stored in the remote control may be
erased in the following cases:
- The remote control is left without batteries for more than 2
minutes.
- Exhausted batteries remain in the remote control.
- The buttons on the remote control are accidentally pressed
when you change batteries.
• If the memory stored in the remote control is unwantedly
erased, insert new batteries and reset the remote control codes
again.
Nates
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
- places of high humidity, such as near a bath
- places of high temperatures, such as near a heater or a stove
- places of extremely low temperatures
- dusty places
• Do not expose the remote control sensor on this unit to direct
sunlight or lighting such as inverted fluorescent lamps.
• If the batteries grow old, the effective operation distance of the
remote control decreases considerably. If this happens, replace
the batteries with two new ones as soon as possible.
24 £n
GETTING STARTED
Using the remote control
This section describes how to control this unit using the
supplied remote control. The functions of the remote
control change depending on the position of the operation
mode selector. Set the operation mode selector to YSP to
switch to the operation mode of this unit. The buttons on
the remote control numbered © to 0 are operational only
when you select YSP. Also, functions of the buttons
numbered ® to ® vary depending on the position of the
operation mode selector. The corresponding functions of
the buttons, see page 9.
You can control other components by setting the appropriate
remote control codes (see page 81). Once the remote control code
for each input source (DVD, VCR, STB, TV or AUX) is set, see
“Controlling other components” on page 82 for further
information on the specific functions of the available remote
control buttons for each input source.
Operational buttons only when YSP is
selected
Turning on the power
Press STANDBY/ON on the front panel or on
the remote control to turn on the power of
this unit.
The volume level appears in the front panel display
and then the input source and beam mode currently
selected are displayed.
ch/J
Front panel
Remote control
2 Press STANDBY/ON on the front panel or on
the remote control again to set this unit to
the standby mode.
Nate
When the unit is in the standby mode, only STANDBY/ON on the
front panel or on the remote control is operational, and the other
control buttons on the front panel or on the remote control are not
operational until the power of this unit is turned on.
25 En
USING SET MENU
Displaying the OSD
This section simply describes how to display the OSD (on-screen display) of this unit on your TV screen and set the
parameters for your listening room. Once this is complete, you can enjoy real surround sound while watching TV in the
comfort of your own home.
Note
The OSD is not output at the COMPONENT VIDEO OUT jacks of this unit. Connect the VIDEO OUT jack of this unit to the video
input jacks of your TV to display the OSD.
Press TV on the remote control to display the
OSD of this unit on your TV screen.
It may take a few seconds before this unit’s OSD
appears on your TV screen.
If the OSD does not appear, use the remote control
provided with your TV to switch the video input until
the OSD appears.
II
1 Check that the video input jack on your TV is
connected to the VIDEO OUT Jacks of this
unit to display the OSD of this unit.
2 Press STANDBY/ON on the front panel or on
the remote control to turn on the power of
this unit.
Front panel
Remote control
3 Turn on the power of your TV.
4 Set the operation mode selector to YSP to
switch to the operation mode of this unit.
OSD screen example
26 En
u
Loading...