Yamaha WaveRunner GP800R (2001) Owner's/operator's Manual
2001
W aveRunner
GP800R
OWNER’S/OPERATOR’S
READ THIS MANUAL
CAREFULLY BEFORE OPERATION!
MANUAL
U.S.A. Edition
LIT-18626-04-05
EJU00270
CAUTION:
To the owner/operator
Thank you for choosing a Yamaha water-
craft.
This Owner’s/Operator’s Manual contains
information you will need for proper operation, maintenance, and care. A thorough
understanding of these simple instructions
will help you to obtain maximum enjoyment
from your new Yamaha. If you have any
questions about the operation or maintenance of your watercraft, please consult a
Yamaha dealer.
Because Yamaha has a policy of continuing product improvement, this product may
not be exactly as described in this Owner’s/
Operator’s Manual. Specifications are subject to change without notice.
This manual should be considered a permanent part of this watercraft and should
remain with it even if the watercraft is subsequently sold.
E
Important manual information:
In this manual, information of particular
importance is distinguished in the following
ways:
The Safety Alert Symbol means
ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!
WARNING
Failure to follow WARNING instructions
could result in severe injury or death to
the machine operator, passenger(s), a
bystander, or a person inspecting or
repairing the watercraft.
A CAUTION indicates special precautions that must be taken to avoid damage
to the watercraft.
NOTE:
A NOTE provides key information to make
procedures easier or clearer.
EJU00271
WaveRunner GP800R
OWNER’S/OPERATOR’S MANUAL
©2000 by Yamaha Motor Corporation, USA
1st Edition, September 2000
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, USA
is expressly prohibited.
Printed in USA
P/N LIT-18626-04-05
EJU00273
CONTENTS
GENERAL AND SAFETY
INFORMATION
E
1
FEATURES AND FUNCTIONS
OPERATION
MAINTENANCE AND CARE
TROUBLESHOOTING AND
EMERGENCY PROCEDURES
2
3
4
5
APPENDIX
READ THIS OWNER’S/OPERATOR’S MANUAL CAREFULLY
BEFORE OPERATING YOUR WATERCRAFT.
6
EJU00274
GENERAL AND
SAFETY
E
INFORMATION
Identification numbers
Primary Identification (PRI-ID) number .. 1-1
Hull Identification Number (HIN).............1-1
Engine serial number..............................1-1
Emission control information
Approval label of Emission control
certificate.................................................1-2
Manufactured date label.........................1-2
Important labels
Label location..........................................1-3
Warning labels ........................................1-4
Caution labels .........................................1-5
Other labels.............................................1-6
Safety information
Limitations on who may operate the
watercraft.................................................1-7
Cruising limitations..................................1-8
Operation requirements..........................1-9
Hazard information ...............................1-12
Watercraft characteristics.....................1-12
Rules of the Road
Steering and sailing rules .....................1-14
Rules when encountering vessels .......1-15
Other special situations ........................1-16
Reading buoys and other markers....... 1-16
To get more boating safety
information
United States Coast Guard ..................1-18
Other sources .......................................1-18
Watercraft Education and Training.......1-18
Enjoy your watercraft responsibly
..............................................1-18
.............................1-1
.................1-2
........................................1-3
..............................1-7
...................................1-14
.......1-19
1
E
EJU00699
Identification numbers
Record your Primary Identification (PRIID) number, Hull Identification Number (HIN)
and engine serial number in the spaces provided, to assist you in ordering spare parts
from a Yamaha dealer. Also record and keep
these ID numbers in a separate place in
case your watercraft is stolen.
EJU00700
Primary Identification (PRI-ID)
number
The PRI-ID number is stamped on a label
attached to the inside of the engine compartment.
EJU00701
Hull Identification Number
(HIN)
The HIN is stamped on a plate 2 attached
to the hull on the aft, starboard side.
EJU00288a
Engine serial number
The engine serial number is stamped on
a label 3 attached to the engine unit.
1-1
1
E
EJU00631a
Emission control
information
This engine conforms to the U.S. Environmental Protection Agency (EPA) regulations
for marine SI engines for the year 2001.
Approval label of Emission
control certificate
This label is attached to the electrical box
and the silencer of the carburetor.
1
Emission control information label
Manufactured date label
This label is attached to the electrical box
and the silencer of the carburetor.
2
Manufactured date label
1-2
EJU00293
Label location
E
Important labels
1-3
E
Warning labels
1
23
1-4
4
5
E
6
78
Caution labels
9
0
AB
1-5
E
Other labels
C
D
EF
G
1-6
E
EJU00686
Safety information
The safe use and operation of this
watercraft is dependent upon the use of
proper riding techniques, as well as upon
the common sense, good judgment, and
expertise of the operator. Every operator
should know the following requirements
before riding the watercraft.
● Before operating the watercraft, read the
Owner’s/Operator’s Manual, the Riding
Practice Guide, the Riding Instruction
card and all warning and caution labels
on the watercraft. Also, watch the Basic
Orientation Video provided with your
watercraft. These materials should give
you an understanding of the watercraft
and its operation.
● Never allow anyone to operate this water-
craft until they too have read the Owner’s/
Operator’s Manual, the Riding Practice
Guide, the Riding Instruction card and all
warning and caution labels, and if possi-
ble watched the Basic Orientation Video.
Showing them the video may help rein-
force the information contained in these
materials.
EJU00667a
Limitations on who may
operate the watercraft
● Yamaha recommends a minimum opera-
tor age of 16 years old.
Adults must supervise use by minors.
Know the operator age and training
requirements for your state. A boating
safety course is recommended and may
be required in your state. You can find
local rules by contacting the United
States Coast Guard (USCG), the National
Association of State Boating Law Administrators, or your local Power Squadron.
● This watercraft is designed to carry the
operator and one passenger. Never
exceed the maximum load limit or allow
more than 2 persons to ride the watercraft
at one time.
Maximum load: 160 kg (353 lb)
Load is the total weight of cargo, operator and passenger.
● Do not operate the watercraft with a pas-
senger on board until you have considerable practice and experience riding alone.
Operating the watercraft with a passenger
requires more skill. Take the time to
become accustomed to the handling
characteristics of the watercraft before
trying any difficult maneuvers.
1-7
E
EJU00613
Cruising limitations
● Scan constantly for people, objects, and
other watercraft. Be alert for conditions
that limit your visibility or block your vision
of others.
● Operate defensively at safe speeds and
keep a safe distance away from people,
objects, and other watercraft.
● Do not follow directly behind watercraft or
other boats.
● Do not go near others to spray or splash
them with water.
● Avoid sharp turns or other maneuvers
that make it hard for others to avoid you or
understand where you are going.
● Avoid areas with submerged objects or
shallow water.
● Ride within your limits and avoid aggres-
sive maneuvers to reduce the risk of loss
of control, ejection, and collision.
● This is a high performance boat—not a
toy. Sharp turns or jumping wakes or
waves can increase the risk of back/spinal
injury (paralysis), facial injuries, and bro-
ken legs, ankles and other bones. Do not
jump wakes or waves.
● Do not operate the watercraft in rough
water, bad weather or when visibility is
poor; this may lead to an accident causing injury or death. Be alert to the possibility of adverse weather. Take note of
weather forecasts and the prevailing
weather conditions before setting out on
your watercraft.
● As with any water sport, you should not
ride your watercraft without someone else
near by. If you ride further than swimming
distance from shore, you should ride by
another boat or watercraft, but make sure
you stay a safe distance away. It’s good
common sense!
● Never operate in water that is less than
60 cm (2 ft) deep, otherwise you increase
your chance of hitting a submerged
object, which could result in injury.
1-8
● This watercraft is not equipped with light-
ing required for night operation. Do not
operate the watercraft after sunset or
before dawn, otherwise you increase the
risk of colliding with another boat, which
could result in severe injury or death.
E
EJU00735a
Operation requirements
● All riders must wear a Coast Guard
approved personal flotation device (PFD)
that is suitable for personal watercraft
use.
● Wear protective clothing. Severe internal
injuries can occur if water is forced into
body cavities as a result of falling into
water or being near the jet thrust nozzle.
Normal swimwear does not adequately
protect against forceful water entry into
rectum or vagina. All riders must wear a
wetsuit bottom or clothing that provides
equivalent protection. Such clothing
includes thick, tightly woven, sturdy and
snug-fitting apparel such as denim, but
does not include spandex or similar fabrics, like those used in bicycle shorts.
1
Coast Guard approved PFD
2
Wetsuit bottom
● Eye protection is recommended to keep
wind, water, and glare from the sun out of
your eyes while you operate your watercraft. Restraining straps for eyewear are
made which are designed to float should
your eyewear fall in the water.
Footwear and gloves are recommended.
1-9
● Helmets meeting Snell or DOT standards
are required for IJSBA-sanctioned races.
You must decide whether to wear a hel-
met while you ride for recreation. You
should know that a helmet could help pro-
tect you in certain kinds of accidents and
that it could also injure you in others.
A helmet is designed to provide some
head protection. Although helmets cannot
protect against all foreseeable impacts, a
helmet might reduce your injuries in a col-
lision with a boat or other obstacle.
A helmet may have potential safety haz-
ards, as well. Falling into the water could
risk the chance of the helmet catching
water, commonly known as “bucketing,”
and the resulting strain on your neck
could cause choking, severe and perma-
nent neck injuries, or death. A helmet
could also increase the risk of an accident
if it reduces your vision or hearing, or if it
distracts you or increases your fatigue.
How should you decide if a helmet’s
potential safety benefits outweigh its
potential risks for you? Consider your par-
ticular riding conditions. Consider factors
such as your riding environment, your
riding style and your riding ability. Also
consider the likelihood of traffic conges-
tion, and the water surface conditions. If
you decide to wear a helmet based upon
your riding circumstances, choose one
carefully. Look for a helmet designed for
personal watercraft use, if possible. Con-
sider a helmet meeting Snell or DOT stan-
dards. If you will be engaging in closed-
course competition, follow the helmet
requirements of the sanctioning organiza-
tion.
E
● NEVER operate the watercraft after con-
suming alcohol or taking other drugs.
● For reasons of safety and proper care of
the watercraft, always perform the preoperation checks listed on page 3-5
before operating the watercraft.
● The operator and passenger should
always keep both feet in the footwell when
the watercraft is in motion. Lifting your
feet increases your chances of losing your
balance, and your feet being hit by objects
outside the watercraft. Do not give a ride
to a child whose feet cannot reach the
floor of the footwell.
● Passenger should firmly hold on to the
operator.
● Always consult your doctor on whether it
is safe for you to ride this watercraft if you
are pregnant or in poor health.
1-10
● Do not attempt to modify this watercraft!
Modifications to your watercraft may
reduce safety and reliability, and render
the watercraft unsafe or illegal for use.
● Attach the engine shut-off cord (lanyard)
to wrist and keep it free from the handle-
bars so that the engine stops if the opera-
tor falls off. After riding, remove the
engine shut-off cord from the watercraft to
avoid accidental starting or unauthorized
use by children or others.
● Scan carefully for swimmers and stay
away from swimming areas. Swimmers
are hard to see and you could acciden-
tally hit someone in the water.
● Avoid being hit by another boat! You
should always take the responsibility to
watch for traffic; other boaters may not be
watching for you. If they do not see you,
or you maneuver more quickly than other
boaters expect, you risk a collision.
● Maintain a safe distance from other boats
or watercraft, and also watch for boats’ ski
ropes or fishing lines. Obey the “Rules of
the Road,” and be sure to check behind
you before making a turn. (See Rules of
the Road on pages 1-14 to 1-17.)
E
F0P03010
● This watercraft is included in the Class A
inboard boat classification of the U.S.
Coast Guard. A watercraft of this type
MUST carry a fire extinguisher of a B-1
classification, with a capacity of two
pounds or more when navigating in
waters under Coast Guard jurisdiction. In
addition, most state and local boating
laws also require that the fire extinguisher
be approved by the USCG.
1-11
E
EJU00313
Hazard information
● When transporting or storing your water-
craft, always place the fuel cock knob in
the “OFF” position, otherwise gasoline
may overflow from the carburetor.
● Never start the engine or let it run for any
length of time in an enclosed area.
Exhaust fumes contain carbon monoxide,
a colorless, odorless gas that may cause
loss of consciousness and death within a
short time. Always operate the watercraft
in an open area.
EJU00315a
Watercraft characteristics
● Jet thrust turns the watercraft. Releasing
the throttle completely produces only minimum thrust. If you are traveling at speeds
above trolling, you will have rapidly
decreasing ability to steer without throttle.
You may still have some turning ability
immediately after releasing the throttle,
but once the engine slows down, the
watercraft will no longer respond to handlebar input until you open the throttle
again or you reach a trolling speed. Practice turning in an open area without
obstructions until you have a good feel for
this maneuver.
● This watercraft are water-jet propelled.
The jet pump is directly connected to the
engine. This means that jet thrust will produce some movement whenever the
engine is running. There is no “neutral”
position.
● Keep away from intake grate 1 while the
engine is on. Items such as long hair,
loose clothing, or PFD straps can become
entangled in moving parts resulting in
severe injury or drowning.
● Never insert any object into the jet thrust
nozzle 2 while the engine is running.
Severe injury or death could result from
coming in contact with the rotating parts
of the jet pump.
1-12
● Stop the engine and remove the clip 3
from the engine shut-off switch 4 before
removing any debris or weeds, which may
have collected around the jet intake.
E
1-13
E
EJU00319
Rules of the Road
Yamaha watercraft is legally considered a powerboat. Operation of the
watercraft must be in accordance with
the rules and regulations governing the
waterway on which it is used.
Just as there are rules that apply when
you are driving on streets and highways,
there are waterway rules that apply when
you are operating your watercraft. These
rules are used internationally, and are also
enforced by the United States Coast Guard
and local agencies. You should be aware of
these rules, and follow them whenever you
encounter another vessel on the water.
Several sets of rules prevail according to
geographic location, but are all basically the
same as the International Rules of the
Road. The rules presented here in this
Owner’s/Operator’s Manual are condensed,
and have been provided for your convenience only. Consult your local U.S. Coast
Guard Auxiliary or Department of Motor
Vehicles for a complete set of rules governing the waters in which you will be operating
your watercraft.
Steering and sailing rules
Whenever two vessels on the water meet
one another, one vessel has the right-ofway; it is called the “stand-on” vessel. The
vessel that does not have the right-of-way is
called the “give-way” or “burdened” vessel.
These rules determine which vessel has the
right-of-way, and what each vessel should
do.
Stand-on vessel
The vessel with the right-of-way has the
duty to continue its course and speed,
except to avoid an immediate collision.
When you maintain your direction and
speed, the other vessel will be able to determine how best to avoid you.
Give-way vessel
The vessel which does not have the rightof-way has the duty to take positive and
timely action to stay out of the way of the
stand-on vessel. Normally, you should not
cross in front of the vessel with the right-ofway. You should slow down or change directions briefly and pass behind the other vessel. You should always move in such a way
that the operator of the other vessel can see
what you are doing.
The General Prudential Rule regarding
the right-of-way is that if a collision appears
unavoidable, neither boat has the right-ofway. Both boats must avoid the collision.
In other words, follow the standard rules
except when a collision will occur unless
both vessels try to avoid each other. If that is
the case, both vessels become give-way
vessels.
1-14
E
Rules when encountering
vessels
There are three main situations that you
may encounter with other vessels which
could lead to a collision unless the Steering
Rules are followed:
Meeting: you are approaching another
vessel head-on
Crossing: you are traveling across
another vessel’s path
Overtaking: you are passing or being
passed by another vessel
In the following illustration, your watercraft
is in the center. You should give the right-ofway to any vessels shown in the white area
(you are the give-way vessel). Any vessels
in the shaded area must yield to you (they
are the give-way vessels). Both you and the
meeting vessel must alter course to avoid
each other.
Meeting
If you are meeting another power vessel
head on, and are close enough to run the risk
of collision, neither of you has the right-ofway! Both of you should alter course to avoid
an accident. You should keep the other vessel on your port (left) side. This rule does not
apply if both of you will clear one another if
you continue on your set course and speed.
Crossing
When two power-driven vessels are
crossing each other’s path close enough to
run the risk of collision, the vessel which has
the other on the starboard (right) side must
keep out of the way of the other. If the other
vessel is on your starboard (right) side, you
must keep out of its way; you are the giveway vessel. If the other vessel is on your
port (left) side, remember that you should
maintain course and direction, provided the
other vessel gives you the right-of-way as it
should.
1-15
E
Overtaking
If you are passing another vessel, you are
the give-way vessel. This means that the
other vessel is expected to maintain its
course and speed. You must stay out of its
way until you are clear of it. Likewise, if
another vessel is passing you, you should
maintain your speed and direction so that
the other vessel can steer itself around you.
Other special situations
There are three other rules you should be
aware of when riding your watercraft around
other vessels.
Narrow channels and bends
When navigating in narrow channels, you
should keep to the right when it is safe and
practical to do so. If the operator of a powerdriven vessel is preparing to go around a
bend that may obstruct the view of other
water vessels, the operator should sound a
prolonged blast of four to six seconds on the
whistle. If another vessel is around the bend,
it too should sound the whistle. Even if no
reply is heard, however, the vessel should
still proceed around the bend with caution. If
you navigate such waters with your watercraft, you will need to carry a portable air
horn, available from local marine supply
stores.
Fishing vessel right-of-way
All vessels fishing with nets, lines or
trawls are considered to be “fishing vessels”
under the International Rules. Vessels with
trolling lines are not considered fishing vessels. Fishing vessels have the right-of-way
regardless of position. Fishing vessels cannot, however, impede the passage of other
vessels in narrow channels.
Sailing vessel right-of-way
Sailing vessels should normally be given
the right-of-way. The exceptions to this are:
1. When the sailing vessel is overtaking the
power-driven vessel, the power-driven
vessel has the right-of-way.
2. Sailing vessels should keep clear of any
fishing vessel.
3. In a narrow channel, a sailing vessel
should not hamper the safe passage of a
power-driven vessel that can navigate
only in such a channel.
Reading buoys and other
markers
The waters of the United States are
marked for safe navigation by the lateral
system of buoyage. Simply put, buoys and
markers have an arrangement of shapes,
colors, numbers and lights to show which
side of the buoy a boater should pass on
when navigating in a particular direction.
The markings on these buoys are oriented
from the perspective of being entered from
seaward (the boater is going towards the
harbor). Red buoys are passed on your starboard (right) side when proceeding from
open water into the harbor, and black buoys
are to your port (left) side. An easy way to
remember the meaning of the colors is the
phrase “red right returning.” When navigating out of the harbor, your position with
respect to the buoys should be reversed; red
buoys should be to port and black buoys to
starboard.
Many bodies of water used by boaters are
entirely within the boundaries of a particular
state. The Uniform State Waterway Marking
System has been devised for these waters.
1-16
E
This system uses buoys and signs with
distinctive shapes and colors to show regulatory or advisory information. These markers are white with black letters and orange
borders. They signify speed zones,
restricted areas, danger areas, and general
information.
Remember, markings may vary by geographic location. Always consult local boating authorities before riding your watercraft
in unfamiliar waters.
1-17
E
EJU00320
To get more boating
safety information
Be informed about boating safety. Additional publications and information can be
obtained from many organizations, including
the following.
United States Coast Guard
Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer
Affairs
U.S. Coast Guard Headquarters
Washington, D.C. 20593-0001
Boating Safety Hotline: 1-800-368-5647
Other sources
You can find local rules by contacting the
National Association of State Boating Law
Administrators, or your local Power Squadron.
Watercraft Education and
Training
The Online Boating Safety Course, available through the watercraft section of the
yamaha-motor.com website, is a free,
50 question learning course available to the
public. Upon successful completion of
80 percent or better, the user can request a
certificate of completion by mail or can
download one immediately. The Online
Boating Safety Course, provided by the
Boat/US Foundation, is approved by the
National Association of State Boating Law
Administrators (NASBLA) and recognized
by the United States Coast Guard. This
course meets the education requirement for
those states that recognize non-proctored,
NASBLA-approved courses.
Yamaha is the watercraft industry’s leading manufacturer to build awareness and
support for boating education. In 1997,
Yamaha launched its GET W.E.T. (Watercraft Education and Training) initiative and
has since reached out to over one million
Americans promoting the benefits of boating
education.
The Online Boating Safety Course:
http://www.boatus.com/onlinecourse/
1-18
EJU00322
Enjoy your watercraft
responsibly
You share the areas you enjoy when
riding your watercraft with others and with
nature. So your enjoyment includes a
responsibility to treat these other people,
and the lands, waters, and wildlife with
respect and courtesy.
Whenever and wherever you ride, think of
yourself as the guest of those around you.
Remember, for example, that the sound of
your watercraft may be music to you, but it
could be just noise to others. And the exciting splash of your wake can make waves
others won’t enjoy. Avoid riding close to
shoreline homes and waterfowl nesting
areas or other wildlife areas, and keep a
respectful distance from fishermen, other
boats, swimmers, and populated beaches.
When travel in areas like these is unavoidable, ride slowly and obey all laws.
Remember that pollution can be harmful
to the environment. Do not refuel or add oil
where a spill could cause damage to nature.
Remove your watercraft from the water and
move it away from the shoreline before refueling. And keep your surroundings pleasant
for the people and wildlife that share the
waterways: don’t litter!
When you ride responsibly, with respect
and courtesy for others, you help ensure
that our waterways stay open for the enjoyment of a variety of recreational opportunities.
E
1-19
EJU00326
FEATURES AND
FUNCTIONS
E
Location of main components
Operation of controls and other
functions
Seat .........................................................2-5
Hood........................................................2-6
Fuel tank filler cap...................................2-6
Oil tank filler cap......................................2-6
Fuel cock knob........................................2-7
Engine stop switch..................................2-8
Engine shut-off switch............................. 2-8
Choke lever.............................................2-8
Throttle lever ...........................................2-9
Start switch..............................................2-9
Cooling water pilot outlet ......................2-10
Steering system ....................................2-10
Quick Shift Trim System (QSTS)
selector..................................................2-11
Engine overheat warning system......... 2-13
Handgrip................................................2-14
Multifunction information center ...........2-15
Tachometer...........................................2-16
Speedometer ........................................2-16
Reset button..........................................2-16
Fuel meter.............................................2-17
Hour meter ............................................2-17
Fuel warning indicator...........................2-18
Oil warning indicator .............................2-18
Engine overheat warning indicator....... 2-18
Storage compartments .........................2-19
Yamaha Adjustable Sponson
(Y.A.S.)..................................................2-20
....................................................2-5
...............2-1
2
EJU00327
Location of main components
Handlebars
1
Use to control direction.
Fuel tank filler cap
2
Rope hole
3
Footwell
4
Use to place feet for balance.
Intake grate
5
Prevents debris from getting into the jet pump.
Speed sensor
6
E
2-1
Cooling water pilot outlet
1
Use to verify cooling water flow.
Bow eye
2
Use to attach rope for transporting, mooring or
towing the watercraft in an emergency.
Front storage compartment
3
Hood
4
Jet intake
5
Handgrip
6
Seat
7
Glove compartment
8
Yamaha Adjustable Sponson (Y.A.S.)
9
E
2-2
E
Engine shut-off cord (lanyard)
1
Attach to wrist so that the engine stops if the
operator falls off the watercraft.
Engine stop switch
2
Push to stop the engine normally.
Clip
3
Insert into the engine shut-off switch to enable
starting of the engine.
Remove to stop the engine or prevent accidental starting of the engine or unauthorized
use of the watercraft.
Quick Shift Trim System (QSTS) selector
4
Use to select the trim angle of the watercraft.
Engine shut-off switch
5
Remove the clip to stop the engine and disable it from starting.
Start switch
6
Push to start the engine.
Multifunction information center
7
Use to check watercraft operation.
Throttle lever
8
Use to accelerate and decelerate.
Choke lever
9
Oil tank filler cap
0
Fuel cock knob
A
Stern drain plugs
B
Use to drain water in the bilge when the watercraft is on dry land.
Jet thrust nozzle
C
Changes the direction of jet thrust according
to handlebar position.
Ride plate
D
2-3
E
Spark plugs/Spark plug caps
1
Electrical box
2
Protects electrical components from water.
Flush hose connector
3
Use to flush the engine cooling water passages.
Spark plug lead
4
Muffler
5
Fuel filter
6
Fuel tank
7
Oil tank
8
Battery
9
Fire extinguisher container
0
Water separator
A
2-4
E
EJU00328
Operation of controls and
other functions
EJU00335a
Seat
There is a seat latch 1 at the rear of the
seat to remove the seat.
To remove the seat:
Pull the seat latch 1 up, and then pull the
seat off.
To install the seat:
Insert the projection on the front of the
seat into the stay on the deck, and then
push the rear of the seat down to lock it in
place securely.
NOTE:
Make sure that the seat is properly secured
before operating the watercraft.
2-5
E
EJU00703
Hood
To open the hood, push the latch 1
down, and then lift the hood up.
To close the hood, push the hood down to
lock it in place.
NOTE:
Make sure that the hood is properly secured
before operating the watercraft.
EJU00347
Fuel tank filler cap
To remove the fuel tank filler cap 1, turn it
counterclockwise.
NOTE:
Make sure that the fuel tank filler cap is
properly secured before operating the watercraft.
EJU00001N
Oil tank filler cap
To remove the oil tank filler cap 2, turn it
counterclockwise.
NOTE:
Make sure that the oil tank filler cap is properly secured before operating the watercraft.
2-6
Loading...