Yamaha T50D, T60D, F60D, F50D User Manual
OWNER’S MANUAL
F50D
T50D
F60D
T60D
U.S.A.Edition
LIT-18626-06-11
6C1-28199-10
EMU25060
Read this owner’s manual carefully before operating your outboard motor.
ZMU01690
Important manual information
EMU25100
To the owner
Thank you for choosing a Yamaha outboard
motor. This Owner’s Manual contains information needed for proper operation, maintenance and care. A thorough understanding
of these simple instructions will help you obtain maximum enjoyment from your new
Yamaha. If you have any question about the
operation or maintenance of your outboard
motor, please consult a Yamaha dealer.
In this Owner’s Manual particularly important
information is distinguished in the following
ways.
The Safety Alert Symbol means
ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!
EWM00780
WARNING
Failure to follow WARNING instructions
could result in severe injury or death
the machine operator, a bystander, or a
person inspecting or repairing the outboard motor.
ECM00700
CAUTION:
A CAUTION indicates special precautions
that must be taken to avoid damage to the
outboard motor.
to
al, please consult your Yamaha dealer.
NOTE:
The F50TR, T50TR, F60TR, T60TR and the
standard accessories are used as a base for
the explanations and illustrations in this
manual. Therefore some items may not apply to every model.
EMU25110
F50D, T50D, F60D, T60D
OWNER’S MANUAL
©2004 by Yamaha Motor Corporation, USA
1st edition, May 2004
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, USA
is expressly prohibited.
Printed in Japan
P/N LIT-18626-06-11
NOTE:
A NOTE provides key information to make
procedures easier or clearer.
Yamaha continually seeks advancements in
product design and quality. Therefore, while
this manual contains the most current product information available at the time of printing, there may be minor discrepancies
between your machine and this manual. If
there is any question concerning this manu-
Table of contents
General information ..........................1
Identification numbers record.......... 1
Outboard motor serial number .......... 1
Key number....................................... 1
Emission control information ........... 1
North American models..................... 1
Star labels ......................................... 2
Safety information ........................... 3
Important labels............................... 4
Warning labels ..................................4
Caution labels ...................................4
Basic boating rules (Rules of the
road) .............................................. 5
Steering and sailing rules and sound
signals............................................. 5
Rules when encountering vessels .... 5
Other special situations..................... 6
Fueling instructions ......................... 8
Gasoline............................................ 9
Engine oil ..........................................9
Battery requirement......................... 9
Battery specifications ...................... 10
Propeller selection......................... 10
Start-in-gear protection ................. 11
Basic components ..........................12
Main components.......................... 12
Fuel tank .........................................12
Fuel joint ......................................... 13
Fuel gauge ...................................... 13
Fuel tank cap .................................. 13
Air vent screw ................................. 13
Remote control................................ 13
Remote control lever....................... 13
Neutral interlock trigger................... 14
Neutral throttle lever........................ 14
Throttle friction adjuster................... 14
Engine stop lanyard switch .............15
Main switch .....................................15
Power trim and tilt switch on remote
control or tiller handle ................... 16
Power trim and tilt switch on bottom
engine cowling .............................. 16
Trim tab with anode ........................ 16
Tilt support lever for power trim and
tilt or hydro tilt model..................... 17
Top cowling lock lever(s) (turn
type) .............................................. 17
Flushing device ...............................17
Tachometer ..................................... 17
Digital tachometer ...........................18
Low oil pressure warning indicator..18
Low oil pressure warning indicator..18
Overheat warning indicator .............19
Overheat warning indicator (digital
type) .............................................. 19
Speedometer (digital type) .............. 19
Trim meter.......................................20
Trim meter (digital type) ..................20
Hour meter (digital type).................. 20
Trip meter........................................21
Clock ...............................................21
Fuel gauge ......................................22
Fuel warning indicator ..................... 22
Low battery voltage warning
indicator ........................................22
Warning system ............................ 23
Overheat warning............................23
Low oil pressure warning ................23
Operation ......................................... 25
Installation..................................... 25
Mounting the outboard motor .......... 25
Breaking in engine ........................ 26
Procedure for 4-stroke models........26
Preoperation checks ..................... 26
Fuel .................................................26
Controls...........................................27
Engine ............................................. 27
Checking the engine oil level ..........27
Filling fuel...................................... 27
Ring Free Fuel Additive................... 28
Operating engine .......................... 28
Feeding fuel (portable tank) ............28
Starting engine ................................ 29
Warming up engine....................... 30
Manual start and electric start
models ..........................................30
Shifting.......................................... 31
Forward (tiller handle and remote
control models) .............................31
Reverse (automatic reverse lock
Table of contents
and power trim and tilt models)..... 31
Stopping engine ............................ 32
Procedure ....................................... 32
Trimming outboard motor.............. 32
Adjusting trim angle ........................ 33
Adjusting boat trim ..........................34
Tilting up and down ....................... 34
Procedure for tilting up.................... 35
Procedure for tilting down ...............36
Cruising in shallow water .............. 36
Power trim and tilt models / power
tilt models...................................... 36
Cruising in other conditions........... 37
Maintenance..................................... 38
Specifications ................................ 38
Transporting and storing outboard
motor ........................................... 39
Storing outboard motor ...................40
Procedure ....................................... 40
Lubrication (except oil injection
models) ......................................... 41
Cleaning and anticorrosion
measures ...................................... 41
Battery care..................................... 42
Flushing power unit......................... 42
Cleaning the outboard motor .......... 43
Checking painted surface of
motor............................................. 43
Periodic maintenance.................... 43
Replacement parts.......................... 44
Maintenance chart .......................... 45
Maintenance chart (additional)........ 46
Greasing ......................................... 47
Cleaning and adjusting spark plug.. 47
Checking fuel system...................... 48
Inspecting fuel filter ......................... 49
Cleaning fuel filter ...........................49
Inspecting idling speed ................... 50
Changing engine oil ........................50
Checking wiring and connectors ..... 52
Exhaust leakage ............................. 52
Water leakage................................. 52
Engine oil leakage........................... 52
Checking power trim and tilt
system .......................................... 52
Checking propeller ..........................53
Removing the propeller ................... 54
Installing the Propeller..................... 54
Changing gear oil ............................ 55
Cleaning fuel tank ...........................56
Inspecting and replacing anode(s) .. 56
Checking battery (for electric start
models) .........................................57
Connecting the battery .................... 58
Disconnecting the battery................ 58
Checking top cowling ......................58
Coating the boat bottom..................59
Trouble Recovery............................ 60
Troubleshooting ............................ 60
Temporary action in emergency ... 63
Impact damage ...............................63
Replacing fuse ................................63
Power trim and tilt will not operate ..64
Starter will not operate ....................64
Emergency starting engine .............65
Treatment of submerged motor .... 66
Procedure........................................ 66
Consumer information ................... 67
Important warranty information for
U.S.A. and Canada ..................... 67
YAMAHA MOTOR
CORPORATION, U.S.A.
FOUR-STROKE OUTBOARD
MOTOR THREE-YEAR LIMITED
WARRANTY ............................... 69
IMPORTANT WARRANTY
INFORMATION IF YOU USE
YOUR YAMAHA OUTSIDE
U.S.A. OR CANADA ................... 71
General information
EMU25170
Identification numbers record
EMU25182
Outboard motor serial number
The outboard motor serial number is
stamped on the label attached to the port
side of the clamp bracket or the upper part of
the swivel bracket.
Record your outboard motor serial number in
the spaces provided to assist you in ordering
spare parts from your Yamaha dealer or for
reference in case your outboard motor is stolen.
1. Outboard motor serial number location
1. Key number
EMU25220
Emission control information
EMU25230
North American models
This engine conforms to U.S. Environmental
Protection Agency (EPA) regulations for marine SI engines. See the label affixed to your
engine for details.
EMU25242
Approval label of emission control certificate
This label is attached to the bottom cowling.
New Technology; (4-stroke/HPDI) EM
EMU25190
Key number
If a main key switch is equipped with the motor, the key identification number is stamped
on your key as shown in the illustration.
Record this number in the space provided for
reference in case you need a new key.
1
1
ZMU03570
1. Approval label location
ZMU01699
EMU25262
Manufactured date label
This label is attached to the clamp bracket or
the swivel bracket.
1
ZMU04701
General information
particular label.
1
ZMU05088
1. Star labels location
EMU25280
One Star—Low Emission
The one-star label identifies engines that
meet the Air Resources Board’s 2001 exhaust emission standards. Engines meeting
these standards have 75% lower emissions
than conventional carbureted two-stroke engines. These engines are equivalent to the
U.S. EPA’s 2006 standards for marine engines.
1. Manufactured date label location
EMU25272
Star labels
Your outboard motor is labeled with a California Air Resources Board (CARB) star label. See below for a description of your
ZMU01702
EMU25290
Two Stars—Very Low Emission
The two-star label identifies engines that
meet the Air Resources Board’s 2004 exhaust emission standards. Engines meeting
these standards have 20% lower emissions
than One Star-Low-Emission engines.
2
General information
ZMU01703
EMU25300
Three Stars—Ultra Low Emission
The three-star label identifies engines that
meet the Air Resources Board’s 2008 exhaust emission standards. Engines meeting
these standards have 65% lower emissions
than One Star-Low-Emission engines.
ZMU01704
EMU25361
Safety information
●
Before mounting or operating the outboard
motor, read this entire manual. Reading it
should give you an understanding of the
motor and its operation.
Before operating the boat, read any own-
●
er’s or operator’s manuals supplied with it
and all labels. Be sure you understand
each item before operating.
Do not overpower the boat with this out-
●
board motor. Overpowering the boat could
result in loss of control. The rated power of
the outboard should be equal to or less
than the rated horsepower capacity of the
boat. If the rated horsepower capacity of
the boat is unknown, consult the dealer or
boat manufacturer.
Do not modify the outboard. Modifications
●
could make the motor unfit or unsafe to
use.
Never operate after drinking alcohol or tak-
●
ing drugs. About 50% of all boating fatalities involve intoxication.
Have an approved personal flotation de-
●
vice (PFD) on board for every occupant. It
is a good idea to wear a PFD whenever
boating. At a minimum, children and nonswimmers should always wear PFDs, and
everyone should wear PFDs when there
are potentially hazardous boating conditions.
●
Gasoline is highly flammable, and its vapors are flammable and explosive. Handle
and store gasoline carefully. Make sure
there are no gas fumes or leaking fuel before starting the engine.
●
This product emits exhaust gases which
contain carbon monoxide, a colorless,
odorless gas which may cause brain damage or death when inhaled. Symptoms include nausea, dizziness, and drowsiness.
Keep cockpit and cabin areas well ventilated. Avoid blocking exhaust outlets.
●
Check throttle, shift, and steering for proper operation before starting the engine.
●
Attach the engine stop switch lanyard cord
to a secure place on your clothing, or your
arm or leg while operating. If you accidentally leave the helm, the cord will pull from
the switch, stopping the engine.
Know the marine laws and regulations
●
where you will be boating—and obey
them. For basic boating rules, see “Rules
3
General information
of the road” on page 5.
●
Stay informed about the weather. Check
weather forecasts before boating. Avoid
boating in hazardous weather.
●
Tell someone where you are going: leave
a Float Plan with a responsible person. Be
sure to cancel the Float Plan when you return.
Use common sense and good judgment
●
when boating. Know your abilities, and be
sure you understand how your boat handles under the different boating conditions
you may encounter. Operate within your
limits, and the limits of your boat. Always
operate at safe speeds, and keep a careful
watch for obstacles and other traffic.
●
Always watch carefully for swimmers during the engine operation.
●
Stay away from swimming areas.
●
When a swimmer is in the water near you
shift into neutral and shut off the engine.
Be informed about boating safety. Additional
publications and information can be obtained
from many organizations, including the following:
United States Coast Guard
Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer Affairs
U.S. Coast Guard Headquarters
Washington, D.C. 20593-0001
Boating Safety Hotline: 1-800-368-5647
National Marine Manufacturers Association (NMMA)
401 N. Michigan Ave.
Chicago, Il 60611
Marine Retailers Association of America
155 N. Michigan Ave.
Chicago, Il 60601
EMU25380
Important labels
EMU25395
Warning labels
ZMU03678
EMU25401
Label
EWM01260
WARNING
●
Be sure shift control is in neutral before
starting engine. (except 2HP)
●
Do not touch or remove electrical parts
when starting or during operation.
●
Keep hands, hair, and clothes away
from flywheel and other rotating parts
while engine is running.
EMU25464
Caution labels
ZMU04702
EMU25472
Label
ECM01190
CAUTION:
Transport and store the engine only as
4
General information
shown. Otherwise, engine damage could
result from Leaking oil.
EMU25500
Basic boating rules (Rules of
the road)
Just as there are rules which apply when you
are driving on streets and high ways, there
are waterway rules which apply when you
are driving your boat. These rules are used
internationally, and are also enforced by the
United States Coast Guard and local agencies. You should be aware of these rules,
and follow them whenever you encounter
another vessel on the water.
Several sets of rules prevail according to
geographic location, but are all basically the
same as the International Rules of the Road.
The rules presented here in your Owner’s
Manual are condensed, and have been provided for your convenience only. Consult
your local U.S. Coast Guard Auxiliary or Department of Motor Vehicles for a complete
set of rules governing the waters in which
you will be using your boat.
EMU25510
Steering and sailing rules and sound
signals
Whenever two vessels on the water meet
one another, one vessel has the right-ofway; it is called the “stand-on” vessel. The
vessel which does not have the right-of-way
is called the “give-way” or “burdened” vessel.
These rules determine which vessel has the
right-of-way, and what each vessel should
do.
Stand-on vessel
The vessel with the right-of-way has the duty
to continue its course and speed, except to
avoid an immediate collision. When you
maintain your direction and speed, the other
vessel will be able to determine how best to
avoid you.
Give-way vessel
The vessel which does not have the right-ofway has the duty to take positive and timely
action to stay out of the way of the Stand-On
vessel. Normally, you should not cross in
front of the vessel with the right-of-way. You
should slow down or change directions briefly and pass behind the other vessel. You
should always move in such a way that the
operator of the other vessel can see what
you are doing.
“The general prudential rule”
This rule is called Rule 2 in the International
Rules and says,
“In obeying and construing these rules due
regard shall be had to all dangers of navigation and collision, and to any special circumstances, which may render a departure from
the above rules necessary in order to avoid
immediate danger.”
In other words, follow the standard rules except when a collision will occur unless both
vessels try to avoid each other. If that is the
case, both vessels become “Give-Way” vessels.
EMU25520
Rules when encountering vessels
There are three main situations which you
may encounter with other vessels which
could lead to a collision unless the Steering
Rules are followed:
Meeting:
sel head-on)
Crossing:
er vessel’s path)
Overtaking:
passed by another vessel)
In the following illustration, your boat is in the
center. You should give the right-of-way to
any vessels shown in white area (you are the
Give-Way vessel). Any vessels in the shad-
(you are approaching another ves-
(you are traveling across the oth-
(you are passing or being
5
General information
ed area must yield to you (they are the GiveWay vessels). Both you and the meeting
vessel must alter course to avoid each other.
Meeting
If you are meeting another power vessel
head on, and are close enough to run the risk
of collision, neither of you has the right-ofway! Both of you should alter course to avoid
an accident. You should keep the other vessel on your port (left) side. This rule doesn’t
apply if both of you will clear one another if
you continue on your set course and speed.
Crossing
When two power driven vessels are crossing
each other’s path close enough to run the
risk of collision, the vessel which has the other on the starboard (right) side must keep out
of the way of the other. If the other vessel is
on your right, you must keep out of its way;
you are the Give-Way vessel. If the other
vessel is on your port (left) side, remember
that you should maintain course and direction, provided the other vessel gives you the
right-of-way as it should.
Overtaking
If you are passing another vessel, you are
the “Give-Way” vessel. This means that the
other vessel is expected to maintain its
course and speed. You must stay out of its
way until you are clear of it. Likewise, if another vessel is passing you, you should
maintain your speed and direction so that the
other vessel can steer itself around you.
EMU25530
Other special situations
There are three other rules you should be
aware of when driving your boat around other vessels.
Narrow channels and bends
When navigating in narrow channels, you
should keep to the right when it is safe and
practical to do so. If the operator of a powerdriven vessel is preparing to go around a
bend that may obstruct the view of other water vessels, the operator should sound a prolonged blast on the whistle (4 to 6 seconds).
If another vessel is around the bend, it too
should sound the whistle. Even if no reply is
heard, however, the vessel should still proceed around the bend with caution. If you
navigate such waters with your boat, you will
need to carry a portable air horn, available
6
General information
from local marine supply stores.
Fishing vessel right-of-way
All vessels which are fishing with nets, lines
or trawls are considered to be “fishing vessels” under the International Rules. Vessels
with trolling lines are not considered fishing
vessels. Fishing vessels have the right-ofway regardless of position. Fishing vessels
cannot, however, impede the passage of
other vessels in narrow channels.
Sailing vessel right-of-way
Sailing vessels should normally be given the
right-of-way. The exceptions to this are:
1. When the sailing vessel is overtaking
the power-driven vessel, the power-driven vessel has the right-of-way.
2. Sailing vessels should keep clear of any
fishing vessel.
3. In a narrow channel, a sailing vessel
should not hamper the safe passage of
a power-driven vessel which can navigate only in such a channel.
Reading buoys and other markers
The waters of the United states are marked
for safe navigation by the lateral system of
buoyage. Simply put, buoys and markers
have an arrangement of shapes, colors,
numbers and lights to show which side of the
buoy a boater should pass on when navigating in a particular direction. The markings on
these buoys are oriented from the perspective of being entered from seaward (the boater is going towards the port). This means that
red buoys are passed on the starboard
(right) side when proceeding from open water into port, and black buoys are to port (left)
side. When navigating out of port, your position with respect to the buoys should be reversed; red buoys should be to port and
black buoys to starboard.
Many bodies of water used by boaters are
entirely within the boundaries of a particular
state. The Uniform State Waterway Marking
System has been devised for these waters.
This system uses buoys and signs with distinctive shapes and colors to show regulatory or advisory information. These markers
are white with black letters and orange
boarders. They signify speed zones, restricted areas, danger areas, and general information.
Remember, markings may vary by geographic location. Always consult local boating authorities before driving your boat in
unfamiliar waters.
7
General information
EMU25540
Fueling instructions
EWM00010
WARNING
GASOLINE AND ITS VAPORS ARE HIGHLY FLAMMABLE AND EXPLOSIVE!
●
Do not smoke when refueling, and keep
ZMU01708
away from sparks, flames, or other
sources of ignition.
●
Stop engine before refueling.
●
Refuel in a well-ventilated area. Refuel
portable fuel tanks off the boat.
●
Take care not to spill gasoline. If gasoline spills, wipe it up immediately with
8
General information
dry rags.
●
Do not overfill the fuel tank.
Tighten the filler cap securely after re-
●
fueling.
●
If you should swallow some gasoline,
inhale a lot of gasoline vapor, or get
gasoline in your eyes, get immediate
medical attention.
If any gasoline spills onto your skin, im-
●
mediately wash with soap and water.
Change clothing if gasoline spills on it.
Touch the fuel nozzle to the filler open-
●
ing or funnel to help prevent electro-
static sparks.
ECM00010
CAUTION:
Use only new clean gasoline which has
been stored in clean containers and is not
contaminated with water or foreign matter.
EMU25570
Gasoline
If knocking or pinging occurs, use a different
brand of gasoline or premium unleaded fuel.
EMU25680
Engine oil
Recommended engine oil:
4-stroke motor oil with a combination
of corresponding SAE and API as
shown in the chart
Engine oil quantity (excluding oil filter):
2.5 L (2.64 US qt) (2.20 Imp.qt)
ECM01050
CAUTION:
All 4-stroke engines are shipped from the
factory without engine oil.
Recommended gasoline:
Regular unleaded gasoline with a minimum octane rating of 86 (Pump Octane Number) = (R+M)/2
Gasohol
There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used
if ethanol content does not exceed 10% and
the fuel meets minimum octane ratings.
Yamaha does not recommended gasohol
containing methanol because it can cause
fuel system damage or engine performance
problems.
9
ZMU01710
EMU25700
Battery requirement
ECM01060
CAUTION:
Do not use a battery that does not meet
the specified capacity. If a battery which
does not meet specifications is used, the
General information
electric system could perform poorly or
be overloaded, causing electric system
damage.
For electric start models, choose a battery
which meets the following specifications.
EMU25711
Battery specifications
Minimum cold cranking amps (CCA/
SAE):
380.0 A
Minimum marine cranking amps (MCA/
ABYC):
502.0 A
Minimum reserve capacity (RC/SAE):
124 minutes
NOTE:
The engine cannot be started if battery voltage is too low.
EMU25742
Propeller selection
The performance of your outboard motor will
be critically affected by your choice of propeller, as an incorrect choice could adversely
affect performance and could also seriously
damage the motor. Engine speed depends
on the propeller size and boat load. If engine
speed is too high or too low for good engine
performance, this will have an adverse effect
on the engine.
Yamaha outboard motors are fitted with propellers chosen to perform well over a range
of applications, but there may be uses where
a propeller with a different pitch would be
more appropriate. For a greater operating
load, a smaller-pitch propeller is more suitable as it enables the correct engine speed
to be maintained. Conversely, a larger-pitch
propeller is more suitable for a smaller operating load.
Yamaha dealers stock a range of propellers,
and can advise you and install a propeller on
your outboard that is best suited to your application.
x
-
123
ZMU04606
1. Propeller diameter in inches
2. Propeller pitch in inches
3. Type of propeller (propeller mark)
x
-
123
ZMU04607
1. Propeller diameter in inches
2. Propeller pitch in inches
3. Type of propeller (propeller mark)
NOTE:
Select a propeller which will allow the engine
to reach the middle or upper half of the operating range at full throttle with the maximum
boat load. If operating conditions such as
light boat loads then allow the engine r/min to
rise above the maximum recommended
range, reduce the throttle setting to maintain
10
General information
the engine in the proper operating range.
For instructions on propeller removal and installation, see page 53.
EMU25770
Start-in-gear protection
Yamaha outboard motors or Yamaha-approved remote control units are equipped
with start-in-gear protection device(s). This
feature permits the engine to be started only
when it is in neutral. Always select neutral
before starting the engine.
11
Basic components
EMU25795
Main components
NOTE:
* May not be exactly as shown; also may not be included as standard equipment on all models.
F50D, T50D, F60D, T60D
1
12
2
11
10
9
8
13
3
4
16
14 15
17 18
SPEED
YAMAHA
TRIP TIME BATT
set
Km/h
knot
mph
km
mile
mode
5
6
7
1. Top cowling
2. Top cowling lock lever
3. Drain screw
4. Anode
5. Anti-cavitation plate
6. Trim tab (anode)
7. Propeller*
8. Cooling water inlet
9. Anode(s)
10. Clamp bracket
11. Tilt support lever
12. Flushing device
13. Remote control box (side mount type)*
14. Digital tachometer*
ZMU05090
15. Digital speedometer*
16. Tachometer*
17. Trim meter*
18. Fuel tank*
EMU25802
Fuel tank
If your model was equipped with a portable
fuel tank, its function is as follows.
EWM00020
WARNING
The fuel tank supplied with this engine is
its dedicated fuel reservoir and must not
be used as a fuel storage container. Com-
12
Basic components
mercial users should conform to relevant
licensing or approval authority regulations.
2
1
4
3
ZMU02284
1. Fuel joint
2. Fuel gauge
3. Fuel tank cap
4. Air vent screw
EMU25830
Fuel joint
This joint is used to connect the fuel line.
EMU25841
Fuel gauge
This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the approximate amount of fuel remaining in the
tank.
EMU25850
Fuel tank cap
This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.
EMU25860
Air vent screw
This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.
EMU26180
Remote control
The remote control lever actuates both the
shifter and the throttle. The electrical switches are mounted on the remote control box.
1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine stop lanyard switch
7. Throttle friction adjuster
EMU26190
Remote control lever
Moving the lever forward from the neutral position engages forward gear. Pulling the lever back from neutral engages reverse. The
engine will continue to run at idle until the lever is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.
1. Neutral “ ”
2. Forward “ ”
3. Reverse “ ”
4. Shift
5. Fully closed
13
6. Throttle
7. Fully open
EMU26201
Neutral interlock trigger
To shift out of neutral, first pull the neutral interlock trigger up.
1. Neutral interlock trigger
EMU26211
Neutral throttle lever
To open the throttle without shifting into either forward or reverse, put the remote control lever in the neutral position and lift the
neutral throttle lever.
NOTE:
The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed
position.
Basic components
1. Fully open
2. Fully closed
EMU25970
Throttle friction adjuster
A friction device provides adjustable resistance to movement of the throttle grip or the
remote control lever, and can be set according to operator preference.
To increase resistance, turn the adjuster
clockwise. To decrease resistance, turn the
adjuster counterclockwise.
EWM00030
WARNING
Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to move throttle lever or grip,
which could result in an accident.
When constant speed is desired, tighten the
adjuster to maintain the desired throttle setting.
14
Basic components
EMU25990
Engine stop lanyard switch
The lock plate must be attached to the engine stop switch for the engine to run. The
lanyard should be attached to a secure place
on the operator’s clothing, or arm or leg.
Should the operator fall overboard or leave
the helm, the lanyard will pull out the lock
plate, stopping ignition to the engine. This
will prevent the boat from running away under power.
EWM00120
WARNING
Attach the engine stop switch lanyard
●
to a secure place on your clothing, or
your arm or leg while operating.
Do not attach the lanyard to clothing
●
that could tear loose. Do not route the
lanyard where it could become entangled, preventing it from functioning.
●
Avoid accidentally pulling the lanyard
during normal operation. Loss of engine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly. This
could cause people and objects in the
boat to be thrown forward.
NOTE:
The engine cannot be started with the lock
plate removed.
1. Lanyard
2. Lock plate
EMU26090
Main switch
The main switch controls the ignition system;
its operation is described below.
●
“”
(off)
With the main switch in the “ ” (off) position, the electrical circuits are off, and the key
can be removed.
“”
(on)
●
With the main switch in the “ ” (on) position, the electrical circuits are on, and the key
cannot be removed.
●
“”
With the main switch in the “ ” (start) position, the starter motor turns to start the engine. When the key is released, it returns
automatically to the “ ” (on) position.
(start)
15
Basic components
EMU26141
Power trim and tilt switch on remote
control or tiller handle
The power trim and tilt system adjusts the
outboard motor angle in relation to the transom. Pressing the switch “ ” (up) trims the
outboard motor up, then tilts it up. Pressing
the switch “ ” (down) tilts the outboard motor down and trims it down. When the switch
is released, the outboard motor will stop in its
current position.
NOTE:
For instructions on using the power trim and
tilt switch, see pages 32 and 34.
EMU26151
Power trim and tilt switch on bottom engine cowling
The power trim and tilt switch is located on
the side of the bottom engine cowling. Pressing the switch “ ” (up) trims the outboard
motor up, then tilts it up. Pressing the switch
“ ” (down) tilts the outboard motor down
and trims it down. When the switch is released, the outboard motor will stop in its
current position.
EWM01030
WARNING
Use the power trim and tilt switch located
on the bottom engine cowling only when
the boat is at a complete stop with the engine off. Attempting to use this switch
while the boat is moving could increase
the risk of falling overboard and could
distract the operator, increasing the risk
of collision with another boat or an obstacle.
UP
DOWN
ZMU03592
NOTE:
For instructions on using the power trim and
tilt switch, see page 34.
EMU26241
Trim tab with anode
The trim tab should be adjusted so that the
steering control can be turned to either the
right or left by applying the same amount of
force.
EWM00840
WARNING
An improperly adjusted trim tab could
cause difficult steering. Always test run
after the trim tab has been installed or replaced to be sure steering is correct. Be
sure you have tightened the bolt after adjusting the trim tab.
If the boat tends to veer the left (port side),
turn the trim tab rear end to the port side “A”
in the figure. If the boat tends to veer the right
(starboard side), turn the trim tab end to the
starboard side “B” in the figure.
ECM00840
CAUTION:
The trim tab also serves as an anode to
16
Basic components
protect the engine from electrochemical
corrosion. Never paint the trim tab as it
will become ineffective as an anode.
3
2
1
B
A
1
ZMU05093
1. Top cowling lock lever(s)
ZMU02525
1. Trim tab
2. Bolt
3. Cap
EMU26340
Tilt support lever for power trim and
tilt or hydro tilt model
To keep the outboard motor in the tilted up
position, lock the tilt support lever to the
clamp bracket.
ZMU03595
EMU26372
Top cowling lock lever(s) (turn type)
To remove the engine top cowling, turn the
lock lever(s) and lift off the cowling. When installing the cowling, check to be sure it fits
properly in the rubber seal. Then lock the
cowling again by returning the lever(s) to the
lock position.
EMU26460
Flushing device
This device is used to clean the cooling water passages of the motor using a garden
hose and tap water.
NOTE:
For details on usage, see page 42.
1
ZMU05095
1. Flushing device
EMU26470
Tachometer
This gauge shows the engine speed and has
the following functions.
17
1
2
ZMU04578
1. Tachometer
2. Warning indicator(s)
EMU26491
Digital tachometer
The tachometer shows the engine speed
and has the following functions.
NOTE:
All segments of the display will light momentarily after the main switch is turned on and
will return to normal thereafter.
Basic components
warning indicators only operate when the engine is equipped with the appropriate functions.
EMU26501
Low oil pressure warning indicator
If oil pressure drops too low, this indicator will
flash. For further information, see page 23.
ECM00020
CAUTION:
Do not continue to run the engine if the
●
low oil pressure warning indicator is on
and the engine oil level is lower. Seri-
ous engine damage will occur.
●
The low oil pressure warning indicator
does not indicate the engine oil level.
Use the oil dipstick to check the re-
maining oil quantity. For further infor-
mation, see page 27.
1
2
3
5
6
1. Tachometer
2. Trim meter
3. Hour meter
4. Low oil pressure warning indicator
5. Overheat warning indicator
6. Set button
7. Mode button
NOTE:
The water separator and engine trouble
7
4
ZMU03601
ZMU04754
EMU26521
Low oil pressure warning indicator
If oil pressure drops too low, the warning indicator will start to blink. For further information, see page 23.
ECM00020
CAUTION:
●
Do not continue to run the engine if the
low oil pressure warning indicator is on
and the engine oil level is lower. Seri-
ous engine damage will occur.
The low oil pressure warning indicator
●
18
Basic components
does not indicate the engine oil level.
Use the oil dipstick to check the remaining oil quantity. For further information, see page 27.
1
ZMU01736
1. Low oil pressure warning indicator
EMU26571
Overheat warning indicator
If the engine temperature rises too high, this
indicator will flash. For further information on
reading the indicator, see page 23.
ECM00050
CAUTION:
Do not continue to run the engine if the
overheat warning indicator is on. Serious
engine damage will occur.
warning indicator will start to blink. For further information on reading the indicator, see
page 23.
ECM00050
CAUTION:
Do not continue to run the engine if the
overheat warning indicator is on. Serious
engine damage will occur.
1
ZMU01737
1. Overheat warning indicator
EMU26600
Speedometer (digital type)
This gauge shows the boat speed.
ZMU04715
EMU26581
Overheat warning indicator (digital
type)
If the engine temperature rises too high, the
19
1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Warning indicator(s)
NOTE:
After the main switch is first turned on, all
segments of the display come on as a test.
Loading...