YAMAHA DSP1D, DSP1D-EX User Manual

Owner’s Manual

-EX

V480360 R3 1 IP 16

100 CR Printed in Japan

E

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all
installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on
different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in
is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : [phone]

Type of Equipment : DSP Unit

Model Name : DSP1D/DSP1D-EX

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference
that may cause undesired operation.

See user manual instructions if interference to radio reception is sus­pected.

* This applies only to products distributed by YAMAHA

CORPORATION OF AMERICA.

WARNING: THIS APPARATUS MUST BE EARTHED

(FCC DoC)

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be
connected to the terminal in the plug which is marked by the letter E
or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig
håndtering. Udskiftning må kun ske med batteri
af samme fabrikat og type. Levér det brugte
batteri tilbage til leverandoren.

VARNING
Explosionsfara vid felaktigt batteribyte. Använd
samma batterityp eller en ekvivalent typ som
rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.

VAROITUS
Paristo voi räjähtää, jos se on virheellisesti
asennettu. Vaihda paristo ainoastaan
laitevalmistajan suosittelemaan tyyppiin. Hävitä
käytetty paristo valmistajan ohjeiden
mukaisesti.

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen
back-up.

• This apparatus contains a lithium battery for memory
back-up.

• Raadpleeg uw leverancier over de verwijdering van de bat­terij op het moment dat u het apparaat ann het einde van
de levensduur of gelieve dan contact op te nemen met de
vertegenwoordiging van Yamaha in uw land.

•For the removal of the battery at the moment of the dis­posal at the end of life please consult your retailer or
Yamaha representative office in your country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small
chemical waste.

(lithium disposal)

This product contains a battery that contains perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate)

Windows® is a registered trademark of Microsoft in the U.S.A. and other countries.

2

86.5

20.5

3.1

4-ø6.5

2-R2

R2

2-R2

R5

t = 1.6

(82.1)

76.2

44.45

31.75

5.9

0

36.5

14.5

7.5

8

0

12

134

200

0

■

Precautions

•Do not place a container with liquid or small metal
objects on top of this unit. Liquid or metal objects inside
this unit are a fire and electrical shock hazard.

•Do not allow water to enter this unit or allow the unit to
become wet. Fire or electrical shock may result.

•Connect this unit’s power cord only to an AC outlet of the
type stated in this Owner’s Manual or as marked on the
unit. Failure to do so is a fire and electrical shock hazard.

•Be sure to connect to an appropriate outlet with a protec­tive grounding connection. Improper grounding can
result in electrical shock.

•Do not scratch, bend, twist, pull, or heat the power cord.
A damaged power cord is a fire and electrical shock haz­ard.

•Do not place heavy objects, including this unit, on top of
the power cord. A damaged power cord is a fire and elec­trical shock hazard. In particular, be careful not to place
heavy objects on a power cord covered by a carpet.

•Be sure to ground the unit to avoid the risk of electrical
shock

•If you notice any abnormality, such as smoke, odor, or
noise, or if a foreign object or liquid gets inside the unit,
turn it off immediately. Remove the power cord from the
AC outlet. Consult your dealer for repair. Using the unit
in this condition is a fire and electrical shock hazard.

• Should this unit/AC adapter/power supply be dropped or
the cabinet be damaged, turn the power switch off,
remove the power plug from the AC outlet, and contact
your dealer. If you continue using the unit without heed­ing this instruction, fire or electrical shock may result.

•If the power cord is damaged (i.e., cut or a bare wire is
exposed), ask your dealer for a replacement. Using the
unit with a damaged power cord is a fire and electrical
shock hazard.

•Do not remove the unit’s cover. You could receive an
electrical shock. If you think internal inspection, mainte­nance, or repair is necessary, contact your dealer.

•Do not modify the unit. Doing so is a fire and electrical
shock hazard.

•When setting up the product, make sure that the AC out­let you are using is easily accessible. If some trouble or
malfunction occurs, immediately turn off the power
switch and disconnect the plug from the outlet. Even
when the power switch is turned off, electricity is still
flowing to the product at the minimum level. When you
are not using the product for a long time, make sure to
unplug the power cord from the wall AC outlet.

•When rack-mounting the unit, allow enough free space
around the unit for normal ventilation. This should be:
10 cm behind, and 20 cm above.

•For normal ventilation during use, remove the rear of the
rack or open a ventilation hole.

•If the airflow is not adequate, the unit will heat up inside
and may cause a fire.

•This unit has ventilation holes at the rear and bottom to
prevent the internal temperature rising too high. Do not
block them. Blocked ventilation holes are a fire hazard.

•Hold the power cord plug when disconnecting it from an
AC outlet. Never pull the cord. A damaged power cord is
a potential fire and electrical shock hazard.

•Do not touch the power plug with wet hands. Doing so is
a potential electrical shock hazard.

•The digital circuits of this unit may induce a slight noise
into nearby radios and TVs. If noise occurs, relocate the
affected equipment.

•If the message “WARNING LOW BATTERY!” appears
when you turn on this unit, contact your dealer as soon
as possible about replacing the internal data backup bat­tery. The unit will still operate correctly, but data other
than the presets will be lost.

•Before you replace the battery, store your data to an ATA­compliant PC flash storage card via the CS1D, or store
the data to the personal computer by connecting the
computer to the PC CONTROL “RS-232-C” connector
on the DSP1D/DSP1D-EX.

•The unit is equipped with the ground connector to avoid
the risk of electrical shock.

•Be sure to ground the unit before you insert the power
plug into an AC outlet.

•If the power cord has three pins and the ground connec­tor on the AC outlet is grounded, the unit will be
grounded effectively.

Operating Notes

•The power must be turned on/off using the POWER
switch of this unit. Do not turn the power on/off by
plugging in the power cable, or by using a power strip or
circuit breaker. Doing so may cause malfunctions.

•Do not rapidly turn on and off the POWER switch of this
unit. Doing so may cause excessive current to damage the
system. You must allow at least five seconds to elapse
between power-on and power-off.

•For this unit, be sure to use a power voltage of the value
specified in the Specifications section of this Owner’s
Manual. If you apply a higher or lower voltage, a mal­function may result.

Rack Mounting Caution

If the unit is rack mounted and transported regularly,
for example, when on a tour, we recommend that the
rear of the unit be supported by fitting a pair metal
brackets, one each side. The following drawing pro­vides the information necessary to make such brackets.
Note that only one bracket is shown here and the
bracket for the other side must be bent in the opposite
direction.

3

22

22

22

22

Thank you for choosing the DSP unit “DSP1D/DSP1D-EX”, specifically designed for the Yamaha PM1D

digital audio mixing system. The DSP1D/DSP1D-EX is an engine controlled by the CS1D control surface.

Be sure to ask an authorized Yamaha service engineer to install the boards and

set up the unit. Never perform installation and setup by yourself.

The following optional boards can be installed in the DSP1D.

• CIB1D : Console interface board

• EMB1D : Engine management board

• PDB1D : Patch DSP board

• GDB1D : Group DSP board

• EDB1D : Effect DSP board

• IDB1D : Input DSP board

Front panel

■

CONFIGURATION

48CH 96CH

ENGINE ID

A B

CONTROL I/O

1 2

INPUT

POWER
ON/ OFF

ENGINE ID

A B

CONTROL I/O

1 2

INPUT

CONFIGURATION

48CH 96CH

1

2

3

Rear panel

■

IN

5

6

OUT

THRU

PC
CONTROL

RS-232-C

USB

WORD CLOCK

IN

MIDI CONTROL I/O

CONSOLE

1

IN

OUT

2

IN

OUT

REMOTE

RS-422

GPI

8

9

J

POWER

ON/ OFF

4

L

CONSOLE

CASCADE

I/O

1IN531 975 31

CONTROL I/O

CONSOLE

OUTPUT INPUT

CONSOLE

CASCADE

I/O

1

IN

1IN531 97531

OUT

2

IN

OUT

REMOTE

RS-422

2OUT64 2 1086 4 2

GPI

TIME CODE IN

DIGITAL I/O

2OUT6 4 2 108 6 4 2

MIDI

IN

OUT

THRU

PC
CONTROL

RS-232-C

USB

WORD CLOCK

IN

OFF

75Ω

ON

OUT

N OM

DIGITAL I/O

OUTPUT INPUT

7

OFF

75Ω

ON

TIME CODE IN

OUT

K

P

4

A

→

→

→

B

→

C

→

D

E

F

G

H

I

J

K

ENGINE ID A/B indicators

These indicators indicate whether the DSP1D/
DSP1D-EX is connected to the engine A or engine B
channel.
Indicator A lights up if the DSP1D/DSP1D-EX is con­nected to the engine A channel jacks of the CS1D con­trol surface (DIGITAL I/O jack A and CONTROL I/O
jack A). Indicator B lights up if the DSP1D/DSP1D­EX is connected to the engine B channel jacks of the
CS1D control surface (DIGITAL I/O jack B and CON­TROL I/O jack B).

Error indication

• If both ENGINE ID A and B indicators are flash­ing:

There is a malfunction in the internal board
(PDB, GDB, IDB1/2, EDB, EMB, or CIB). Or
the necessary board does not exist.

• If either ENGINE ID A or B indicator is flashing:

During the Mirror mode operation, the
ENGINE ID indicator for the unused DSP1D/
DSP1D-EX flashes, indicating that the unit is in
standby mode.

If Indicator A is flashing, unit A is in standby
mode. If Indicator B is flashing, unit B is in
standby mode.

CONTROL I/O 1/2 indicators

These indicators indicate which one of two CON­SOLE 1, 2 IN/OUT jacks ( 8 ) on the rear panel is cur­rently effective.

Note:

When you turn on the power to the DSP1D/
DSP1D-EX and the CS1D, and communication
between the DSP1D/DSP1D-EX and the CS1D is
established, one of these two indicators lights up. If
neither one lights up, check the connection of the
CONSOLE 1, 2 IN OUT jacks on the rear panel.

Error indication

• If the CONTROL I/O 1 indicator is flashing:

Communication between the CS1D control
surface and the DSP1D is not established.The
CONSOLE 1, 2 IN OUT jacks or the PC CON­TROL port is not connected correctly.

INPUT CONFIGURATION 48CH/96CH
indicators

These indicators indicate how many input channels
are currently available. On the DSP1D, the 48CH
indicator lights up. On the DSP1D-EX, the 96CH
indicator lights up.

Error indication

• If the INPUT CONFIGURATION 48CH is flashing:

The signal is not locking to the word clock.

POWER ON/OFF switch

Use this switch to turn the power to the DSP1D/
DSP1D-EX on or off. When the power is turned on,
the indicators 1 - 3 light up.

MIDI IN/OUT/THRU connectors

These connectors are used to transmit and receive
Program change messages, MMC, and other MIDI
messages among external MIDI devices.

PC CONTROL RS-232-C/USB ports

Connect these ports to a PC that runs Windows 2000
or Windows XP to control the PM1D system from the
PC. Use a D-sub, 9-pin cross cable (female to female)
to connect the RS-232-C port to the serial (COM)
port on the PC. Alternatively use a USB cable to con­nect the USB port to the USB port on the PC.

WORD CLOCK IN jack, 75 Ω ON/OFF
switch, and WORD CLOCK OUT jack

The WORD CLOCK IN jack is used to provide word
clock to the PM1D system from the connected exter­nal device, such as a clock generator. Use the WORD
CLOCK OUT jack to provide the word clock to the
connected external device from the PM1D. Use a BNC
cable with an impedance of 75 Ω for the WORD
CLOCK IN/OUT jacks.
The WORD CLOCK ON/OFF switch is used to termi­nate the word clock connection. Basically, if the
DSP1D/DSP1D-EX is the last device of the word clock
chain, or if nothing is connected to the WORD
CLOCK IN/OUT jacks, set this switch to ON.

CONSOLE 1, 2 IN/OUT jacks

These jacks are connected to the CONTROL I/O
CONSOLE jacks of the CS1D control surface to trans­mit or receive control signals. For connection, use a
genuine Yamaha cable or a BNC cable with an imped­ance of 50 Ω .

REMOTE RS-422 connector

This D-sub 9-pin connector is used to control a con­nected tape recorder or a hard disk recorder. Serial
commands can be transmitted through this connector
to play or stop such a recorder.

GPI connector

This connector is used to connect an external device
that supports GPI (General Purpose Interface), such
as a video editor to control the external device from
the PM1D system or to perform certain functions of
the PM1D system while controlling from the external
device. You can connect a custom-made external
switch here.

TIME CODE IN connector

This balanced XLR3-31 connector receives SMPTE
time code (LTC) for analog input from the external
device. The rated input level is –10 dB, and the pin
assignment is as follows.
1=ground, 2=hot, 3=cold

5

L

M

N

O

P

CONSOLE I/O 1, 2 slots

Connect these slots to the DIGITAL I/O CONSOLE
jacks of the CS1D control surface to transmit multi­channel digital audio signals. Use a genuine Yamaha
half-pitch 68-pin cable for connection.

CASCADE IN, OUT slots

Use one of these connectors to cascade two DSP1D/
DSP1D-EX units to transmit multi-channel digital
audio signals. Use a genuine Yamaha half-pitch 68-pin
cable to connect the CASCADE IN (or OUT) to the
CASCADE OUT (or IN) of another DSP1D/DSP1D­EX.

OUTPUT 1–6 slot

Use these slots to connect the INPUT connectors of an
analog output unit AO8 series or DIO8 digital I/O
unit to output multi-channel digital audio signals
from the DSP1D/DSP1D-EX. Use a genuine Yamaha
half-pitch 68-pin cable for connection.

Specifications

■

Sampling frequency

Power supply

Power consumption 170 W

Dimensions (W × H × D) 480 mm × 408.7 mm × 460.8 mm

Weight 33 kg

Operating temperature 10 – 35˚C

Fan circuit always fixed

Accessories power cable 2.5 m × 1

<External sync> 39.69 kHz – 50.88 kHz

<Internal sync> 44.1 kHz, 48 kHz

USA and Canada : 120 V, 60 Hz

Others : 230 V, 50 Hz

INPUT 1–10 slot

Use these slots to connect the OUTPUT connectors of
an analog input unit AI8 series or DIO8 digital I/O
unit series to input multi-channel digital audio signals
to the DSP1D/DSP1D-EX. Use a genuine Yamaha
half-pitch 68-pin cable for connection.

Ground connector

Be sure to ground the unit to avoid the risk of electrical
shock before you insert the power plug into an AC outlet.

This product comes with a 3-pin power cord. If the
ground connector of the AC outlet has already been
grounded, the unit will be grounded effectively by
using the 3-pin power cord.
Grounding the unit is also effective for preventing
hum and other noise.

Digital I/Os

I/O connectors Level Type

DIGITAL I/O INPUT 1 –10 RS-422 D-sub, half-pitch, 68-pin connector (female) × 10

DIGITAL I/O OUTPUT 1 – 6 RS-422 D-sub, half-pitch, 68-pin connector (female) × 6

DIGITAL I/O CASCADE IN, OUT RS-422 D-sub, half-pitch, 68-pin connector (female) × 2

DIGITAL I/O CONSOLE I/O 1, 2 RS-422 D-sub, half-pitch, 68-pin connector (female) × 2

CONTROL I/O CONSOLE 1 IN, OUT –0.225V — –1.825V/50 Ω

CONTROL I/O CONSOLE 2 IN, OUT –0.225V — –1.825V/50 Ω

REMOTE RS-422 RS-422 D-sub, 9-pin connector (female)

GPI

TIME CODE IN SMPTE format, Nominal –10 dB/10 k Ω XLR-3-31 type connector

MIDI IN, OUT, THRU MIDI format 5-pin DIN connector × 3

PC CONTROL RS-232-C RS-232-C D-sub, 9-pin connector (male)

PC CONTROL USB 0V — 3.3V B type USB connector

WORD CLOCK IN TTL/75 Ω (ON/OFF) BNC connector

WORD CLOCK OUT TTL/75 Ω

C-MOS IN, Open collector OUT
1 pin: 150mA, 8pin total: 500mA

BNC connector × 2

BNC connector × 2

D-sub, 25-pin connector (female)

BNC connector

6

Slots (for IDB1D board)

POWER

ON/ OFF

A B

ENGINE ID

1 2

CONTROL I/O

48CH 96CH

INPUT

CONFIGURATION

460.8

450

480

399.2

408.7

9.5

unit: mm

Unit Input channel

DPS1D INPUT 1-48 & ST IN 1-4

DPS1D-EX INPUT 1-96 & ST IN 1-8 (DSP1D + IDB1D for expansion)

*The DSP1D has an empty slot available for the IDB1D board.

■

Dimensions

*

•Specifications and appearance are subject to change without notice for improvement.

•For European Model
Purchaser/User information specified in EN55103-1 and EN55103-2.
Inrush Current: 31A
Conformed Environment: E1, E2, E3 and E4.

7

For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana
o el distribuidor autorizado que se lista debajo.

NORTH AMERICA

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: [phone]

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: [phone]

CENTRAL & SOUTH AMERICA

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,
Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: [phone]

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,
CEP 04534-013 Sao Paulo, SP. BRAZIL
Tel: [phone]

ARGENTINA

Yamaha Music Latin America, S.A.
Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,
Buenos Aires, Argentina
Tel: [phone]

PAN AMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: [phone]

EUROPE

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: [phone]

GERMANY

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: [phone]

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Central Europe GmbH,
Branch Switzerland

Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: [phone]

AUSTRIA

Yamaha Music Central Europe GmbH,
Branch Austria

Schleiergasse 20, A-1100 Wien, Austria
Tel: [phone]

CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA

Yamaha Music Central Europe GmbH,
Branch Austria, CEE Department

Schleiergasse 20, A-1100 Wien, Austria
Tel: [phone]

POLAND

Yamaha Music Central Europe GmbH
Sp.z. o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: [phone]

THE NETHERLANDS/
BELGIUM/LUXEMBOURG

Yamaha Music Central Europe GmbH,
Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: [phone]

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: [phone]

ITALY

Yamaha Musica Italia S.P.A.
Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: [phone]

SPAIN/PORTUGAL

Yamaha-Hazen Música, S.A.

Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: [phone]

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1
Box 30053
S-400 43 Göteborg, Sweden
Tel: [phone]

DENMARK

YS Copenhagen Liaison Office

Generatorvej 6A
DK-2730 Herlev, Denmark
Tel: [phone]

NORWAY

Norsk filial av Yamaha Scandinavia AB

Grini Næringspark 1
N-1345 Østerås, Norway
Tel: [phone]

OTHER EUROPEAN COUNTRIES

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: [phone]

AFRICA

Yamaha Corporation,
Asia-Pacific Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: [phone]

MIDDLE EAST

TURKEY/CYPRUS

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: [phone]

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jubel Ali,
Dubai, United Arab Emirates
Tel: [phone]

ASIA

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

25/F., United Plaza, 1468 Nanjing Road (West),
Jingan, Shanghai, China
Tel: [phone]

INDONESIA

PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: [phone]

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: [phone]

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: [phone]

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building
140 Paya Lebor Road, Singapore 409015
Tel: [phone]

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: [phone]

THAILAND

Siam Music Yamaha Co., Ltd.

891/1 Siam Motors Building, 15-16 floor
Rama 1 road, Wangmai, Pathumwan
Bangkok 10330, Thailand
Tel: [phone]

OTHER ASIAN COUNTRIES

Yamaha Corporation,
Asia-Pacific Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: [phone]

OCEANIA

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: [phone]

COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,
Asia-Pacific Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: [phone]

PA17

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: [phone]

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

© 2001 Yamaha Corporation