Yamaha CRX-D430 Owner's Manual

Download

CD RECEIVER

CRX-D430

OWNER’S MANUAL

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place with at

least 10 cm on the top, 10 cm on the left and right, and 10 cm at the back of this unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical appliances, motors, or

transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold

to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this

unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:

– other components, as they may cause damage and/or

discoloration on the surface of this unit.

– burning objects (i.e. candles), as they may cause fire, damage

to this unit, and/or personal injury.

– containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections are

complete.

8 Do not operate this unit upside-down. It may overheat, possibly

causing damage. 9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cable from the wall outlet, grasp

the plug; do not pull the cable. 11 Do not clean this unit with chemical solvents; this might damage

the finish. Use a clean, dry cloth. 12 Only voltage specified on this unit must be used. Using this unit

with a higher voltage than specified is dangerous and may cause

fire, damage to this unit, and/or personal injury. Yamaha will not

be held responsible for any damage resulting from use of this unit

with a voltage other than specified. 13 To prevent damage by lightning, keep the power cord and outdoor

antennas disconnected from a wall outlet or this unit during a

lightning storm. 14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed.

The cabinet should never be opened for any reasons. 15 When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet. 16 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty. 17 Before moving this unit, press ASTANDBY/ON to set this unit

to the standby mode, and disconnect the AC power plug from the

wall outlet. 18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power cable from the outlet,

then leave this unit alone. 19 When using this unit for a long time, this unit may become warm.

Turn the power off, then leave this unit alone for cooling. 20 The batteries shall not be exposed to excessive heat such as

sunshine, fire, or like. 21 Install this unit near the AC outlet and where the AC power plug

can be reached easily.

22 Excessive sound pressure from earphones and headphones can

cause hearing loss.

CAUTION

The use of optical instruments with this product will increase eye hazard.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

The laser component in this product is capable of emitting radiation exceeding the limit for Class 1.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Make sure that neither core is connected to the earth terminal of the three pin plug.

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

APPENDIX

ENJOYING

PLAYBACK

ENJOYING

RADIO

Controls on the front panel.................................... 2

Controls on the remote control ............................. 3

Making preparations .............................................. 4

Connecting speakers/an external

component/antennas .............................................. 4

Installing batteries in the remote control ................... 5

Adjusting the clock .................................................... 5

Basic operation of this unit .................................... 6

Turning on the power................................................. 6

Selecting an input source ........................................... 6

Adjusting the volume level ........................................ 6

Adjusting sounds ....................................................... 6

Listening through the headphones............................. 6

Changing the brightness of the display...................... 6

Setting a wake-up timer ............................................. 7

Setting a sleep timer................................................... 7

Playback operations ................................................8

Playing back discs ..................................................... 8

Repeat playback......................................................... 9

Random playback ...................................................... 9

Program playback ...................................................... 9

Index search (Audio CD only)................................. 10

Listening to your iPod™ ......................................... 10

Switching the playback information display ........... 11

Listening to FM/AM broadcast............................12

Selecting broadcast stations..................................... 12

Presetting broadcast stations automatically............. 12

Selecting preset stations........................................... 12

Editing the name of the preset radio stations........... 12

Receiving radio data system information ................ 13

Listening to DAB broadcast .................................14

Listening to DAB stations ....................................... 14

Advanced DAB operations ...................................... 14

Switching the DAB information.............................. 15

Troubleshooting.....................................................16

General..................................................................... 16

Disc playback .......................................................... 17

iPod™ playback....................................................... 17

Radio reception........................................................ 18

Remote control ........................................................ 18

Notes on discs.........................................................19

Disc information ...................................................... 19

Handling a disc ........................................................ 19

Glossary..................................................................20

Specifications .........................................................21

• Minimum RMS output power

(6 Ω , 1 kHz, 0.1% THD) 25 W + 25 W

• iPod playback function

• Sophisticated DAB/FM/AM tuner

• Playability of music CDs and MP3/WMA discs

• Easy operation with multi jog dial

• Random and direct preset tuning

■ Supplied accessories

Before using this product, make sure you received all of the following accessories.

❏ Remote control (☞ P. 3 ) ❏ Batteries (AAA, R03, UM-4) (x2) (☞ P. 5) ❏ Indoor FM antenna (☞ P. 5 ) ❏ AM loop antenna (☞ P. 5) ❏ Indoor DAB antenna (☞ P. 5) ❏ Dock cover (☞ P. 2)

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ENJOYING PLAYBACK

ENJOYING RADIO

APPENDIX

Features

About this manual

• y indicates a tip for your operation.

• Notes contain important information about safety and operating instructions.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority.

CONTROLS ON THE FRONT PANEL

2 En

The circled alphabets (A to O) correspond to the ones in the operation descriptions.

STANDBY/ON (☞ P. 5, 6, 7)

Display (☞ P. 11, 15)

Disc tray (☞ P. 8)

(open/close tray) (☞ P. 8)

(play), BAND (☞ P. 6, 8, 9, 12, 14)

(pause) (☞ P. 8)

(stop), CLEAR

(☞ P. 8, 9, 10, 12, 13)

PHONES jack (☞ P. 6 )

TIME MODE (☞ P. 5, 6, 7)

Multi jog dial

FUNCTION (☞ P. 6, 10, 12, 14, 15)

PROGRAM/MEMORY (☞ P. 9, 10, 12)

Remote control sensor (☞ P. 3)

INPUT (☞ P. 6 , 8, 10, 12)

VOLUME (☞ P. 6 )

Controls on the front panel

POWER

STANDBY/ON

PHONES

TIME

MODE

FUNCTION

PROGRAM

/MEMORY

BAND

VOLUM E

INPUT

CLEAR

TUNING/PRESET/TIME

PUSH-ENTER

ABC DEFG

HI J KL M N O

iPod

Top view

iPod terminal (☞ P. 10)

Dock cover (supplied)

You can attach the dock cover to protect the terminal when you do not use your iPod with this unit.

3 En

INTRODUCTION

The circled numbers (1 to L) correspond to the ones in the operation descriptions.

1 STANDBY/ON (☞ P. 6, 7) 2 Input selector buttons (☞ P. 6, 10, 12) 3 TIMER (☞ P. 7 ) 4 DIMMER (☞ P. 6 ) 5 Numeric buttons (☞ P. 8, 9, 10, 12) 6 PROG, MEMORY (☞ P. 9, 10, 12) 7 RANDOM (☞ P. 9) 8 REPEAT (☞ P. 9) 9 INFO (☞ P. 11, 13, 15)

0 , , , MENU, ENTER, ,

(☞ P. 6, 8, 9, 10, 12, 14, 15)

A (☞ P. 8 )

B FOLDER / (☞ P. 8) C SLEEP (☞ P. 7 ) D BAND (☞ P. 6, 12, 14) E INDEX (☞ P. 10) F PRESET / (☞ P. 12)

G TUNING / (☞ P. 12) H CLEAR (☞ P. 9, 10, 12) I FUNCTION (☞ P. 6 , 10, 12, 14, 15) J A-B (☞ P. 9) K VOLUME +/– (☞ P. 6 ) L MUTE (☞ P. 6 )

Use the remote control within 6 m of this unit and point it toward the remote control sensor.

• Be careful not to spill liquid on the remote control.

• Be careful not to drop the remote control.

• Do not leave the remote control in the following places: – hot or humid places, such as near a heater or in a bathroom – extremely cold places – dusty places

Controls on the remote control

MUTE

FOLDER VOLUME

ENTER

INFO

RANDOM FUNCTION

A-BREPEAT

PROG

MEMORY

CLEAR

TIMER

STANDBY/ON

SLEEP

DIMMER INDEX BAND

AUX

iPod

TUNER

789

TUNING

PRESET

456

H I

6 7

Lights up when button is pressed.

30˚ 30˚

Within 6 m

Notes

RUNNING H/F 1

4 En y The circled numbers and alphabets correspond to the ones on the attached sheet.

• Turn off the audio component before connecting it to this unit.

• Also refer to the instructions of the components to be connected.

•

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly.

• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/ or the speakers.

• Use speakers with 6 Ω or higher impedance.

• Digital signals are output at the DIGITAL OPTICAL jack only when you play a disc with this unit.

Making preparations

Connecting speakers/an external component/antennas

CAUTION

Do not connect the power cable of this unit until all cable connections are completed.

Notes

OUT

OUT IN

AUX

FM ANT GND AM ANT

TUNER

DAB ANT

SUBWOOFER

OUT

DIGITAL

OPTICAL

SPEAKERS

6 MIN./SPEAKER

75 UNBAL

INPUT

OUTPUT

OPTICAL IN

CD-R, etc.

Left speakerRight speaker

Optical cable

When you connect an external component using an optical cable, insert the cable plug until it makes a click sound.

Subwoofer

Subwoofer cable

10 mm

Audio cables

Be sure to insert each plug securely.

■ Connecting speaker cables

Making preparations

5 En

PREPARATION

If there is a problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use commercially available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center.

• Do not use an old battery together with new one.

• Do not use different types of batteries (for example, alkaline and manganese) together.

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.

• Dispose of the batteries according to the regional regulations.

• If a battery starts leaking, dispose of it immediately. Be careful not to let leaking battery acid come into contact with your skin or clothing. Before inserting new batteries, wipe the compartment clean.

(Operation available only on the front panel)

1 Press

STANDBY/ON to turn on this unit.

2 Press

TIME MODE to select “TIME” and

then push the multi jog dial (J).

3 Rotate and push the multi jog dial (

) to

set the current hour.

4 Rotate and push the multi jog dial (

) to

set the current minute.

5 Push the multi jog dial (

) again to

complete the time setting.

The clock is displayed in 24-hour format.

Adjust the clock before using the timer function of this unit.

OUT

OUT IN

AUX

FM ANT GND AM ANT

TUNER

DAB ANT

SUBWOOFER

OUT

DIGITAL OPTICAL

SPEAKERS

6 MIN./SPEAKER

75 UNBAL

Indoor FM antenna (supplied)

Indoor DAB antenna (supplied)

Extend the cord vertically and attach it to a window frame or wall using drawing pin, etc.

Ground (GND terminal)

To an AC wall outlet

AM loop antenna (supplied)

Installing batteries in the remote control

Notes

Batteries (supplied)

Make sure you insert the batteries according to the polarity markings (+ and –).

Adjusting the clock

Note

Basic operation of this unit

6 En y The circled numbers and alphabets correspond to the ones on the attached sheet.

Press 1STANDBY/ON (or ASTANDBY/ON) to turn on this unit.

Press it again to set this unit to the standby mode.

• You can select whether to display the clock (ECO OFF mode) or not (ECO ON mode) when this unit is in the standby mode. Press and hold ITIME MODE during standby mode until “ECO OFF” or “ECO ON” appears.

• To charge your iPod while this unit is in the standby mode, select “ECO OFF”.

• The memory back-up circuit prevents the clock setting from being lost even if this unit is in the standby mode. However, the clock setting will be lost if the power cable is disconnected from the AC wall outlet or if the power supply is cut off for more than four minutes.

• In the standby mode, this unit consumes a small amount of power.

Press one of the input selector buttons (2) repeatedly (or press NINPUT) to select the input source from CD, iPod, TUNER (FM/AM/ DAB), and AUX.

• Press DBAND (or EBAND) to select FM, AM, or

DAB.

• For details on CD, iPod, and tuner operations, refer to

pages 8, 10, 12, and 14.

• When you select AUX, this unit outputs sound played

back on the component which is connected to the AUX IN jacks. While AUX is selected as the input source, this unit does not output signals at the AUX OUT jacks.

Press KVOLUME + (or rotate OVOLUME clockwise) to increase the volume level and press KVOLUME – (or rotate it counterclockwise) to decrease it.

■ Muting the sound

Press LMUTE.

To restore audio output to the previous volume level, press it again or press KVOLUME +/–.

1 Press

FUNCTION (or KFUNCTION).

2 Press

/ repeatedly (or rotate the multi jog dial (J)) to select the setting from “Bass” (low frequency), “Treble” (high frequency), and “Balance” (speaker balance), and then press 0ENTER (or push the multi jog dial (J)).

3 Press

/ repeatedly (or rotate the multi jog dial (J)) to adjust the setting and then press 0ENTER (or push the multi jog dial (J)).

The setting ranges are as follows:

Bass ..................... –10 dB to +10 dB

Treble................... –10 dB to +10 dB

Balance................ L +6 to R +6

These settings have no effect on the audio signals output at the AUX OUT jacks and the DIGITAL OPTICAL OUT jack.

Connect the headphone plug to the HPHONES jack.

While headphones are connected, the sound from the speakers and subwoofer is cut off.

Press 4DIMMER repeatedly.

You can select the brightness level from bright, mid dim, and dim.

Basic operation of this unit

Turning on the power

Selecting an input source

Adjusting the volume level

Adjusting sounds

Note

Listening through the headphones

Changing the brightness of the display

Basic operation of this unit

7 En

BASIC

OPERATION

You can turn on this unit and play the selected input source automatically at a specified time. Also, you can set this unit to the standby mode after a certain time.

Adjust the clock before setting the timer (☞ P. 5 ).

(Operation available only on the front panel)

1 Press

TIME MODE repeatedly until “TIMER” appears, and then push the multi jog dial (J).

2 Rotate and push the multi jog dial (

)

clockwise to select “TIMER ON”.

3 Rotate and push the multi jog dial (

) to set the time (hour and minute) you want to start playback.

4 Rotate and push the multi jog dial (

) to select the input source you want to play back.

You can select the input source from FM, AM, DAB, CD, and iPod.

When you select CD, the playback begins with the first track/file. When you select iPod, the playback resumes from where it was stopped.

5 Rotate and push the multi jog dial (

) to set the duration time.

You can set the duration time in 10-minute steps (30 to 90 minutes). When you select “– –”, this unit does not turn to the standby mode automatically.

While a wake-up timer is activated, appears at the right top of the display.

6 Press

STANDBY/ON (or ASTANDBY/

ON) to set this unit to the standby mode.

You can set this unit to the standby mode by using the sleep timer function.

■ To cancel the wake-up timer

Select “TIMER OFF” in step 2.

Once you set a wake-up timer, you can activate or deactivate it by pressing 3TIMER.

This unit automatically turns to the standby mode after the specified interval.

Press CSLEEP repeatedly to set the interval for the sleep timer.

You can select the interval from 30 minutes, 60 minutes, and 120 minutes. The display automatically dims when the sleep timer is activated.

■ To set the sleep timer more accurately

1 Press

TIME MODE repeatedly until “SLEEP” appears, and then push the multi jog dial (J).

2 Rotate and push the multi jog dial (

) to

set the interval (5 to 240 minutes).

You can set the interval in 5-minute steps (5 to 60 minutes), 10-minute steps (60 to 120 minutes), or 30minute steps (120 to 240 minutes).

■ To cancel the sleep timer

Press CSLEEP repeatedly until the normal display appears. Also, you can cancel the sleep timer by selecting “SLEEP OFF” in the step 2 of “To set the sleep timer more accurately”.

• The sleep timer does not turn off other component connected to this unit.

• The sleep timer is canceled if you turn this unit to the standby mode.

While a sleep timer is activated, appears at the right top of the display.

Setting a wake-up timer

Note

Setting a sleep timer

Notes

SLEEP

Playback operations

8 En y The circled numbers and alphabets correspond to the ones on the attached sheet.

Some operations may be different or restricted depending on the disc. Before playing back, check the compatibility of your disc with this unit (☞ P. 19).

1 Press

INPUT repeatedly to select “CD”.

2 Press

and then place a CD on the disc

tray with the printed label facing up.

If you press D while this unit is in the standby mode, this unit turns on with CD selected and the disc tray opens.

3 Press

(or

The disc tray closes and playback starts automatically.

When this unit is turned on with a disc loaded, disc playback starts automatically.

■ To stop playback

Press

(or

■ To pause playback

Press

(or F). To return to normal playback,

press

(or E).

■ To skip tracks

• To skip to the start of the current track, press

(or rotate the multi jog dial (J) counterclockwise one click).

• To skip to the next track, press

(or rotate the

multi jog dial (J) clockwise one click).

• To skip to the previous track, press

twice (or

rotate the multi jog dial (J) counterclockwise two clicks).

■ To search backward/forward

• For backward search, press and hold

• For forward search, press and hold

You can push the multi jog dial (J) and rotate it counterclockwise/clockwise for backward/forward search. Push it again to cancel search.

■ To specify a track for playback

Press the numeric button(s) (5) to enter the track number you want to play.

For an MP3 or WMA disc, the number assigned to each file corresponds to the file sequence in the disc, not in the individual folders.

■ To select a folder/file for an MP3 or WMA format file

1 Press

FOLDER / to select a folder,

and press 0ENTER.

2 Press

/ to select a file.

3 Press

ENTER to start playback of the

selected folder/file.

■ About MP3 or WMA files

You can play back MP3 or WMA files recorded on your CD-R or CD-RW. This unit regards folders in a disc as albums, and files as tracks as shown below. Folder hierarchy is disregarded.

• Depending on the conditions of recording such as software

recording setting, this unit may not be able to play a disc in the order shown above.

• The folders/files within the same level are played back in the

alphanumeric order.

• This unit can play back up to 255 files and 255 folders.

However, less than 255 files/folders may be displayed if some files/folders are not playable on this unit.

• Copyright-protected files cannot be played back.

Playback operations

Playing back discs

Note

Notes

1 2

3 4

7 8

5 6

Folder (Album)

File (Track)

Root directory

Playback operations

9 En

ENJOYING

PLAYBACK

Press 8REPEAT repeatedly to select the desired repeat play mode.

The repeat playback mode changes as follows:

■ To repeat between two points (A-B repeat)

1 During playback, press

A-B at the point

where you want to start repeat playback.

2 Press

A-B again at the point where you

want to end repeat playback.

■ To cancel A-B repeat

Press JA-B again.

Repeat playback mode is canceled when the disc is removed.

Press 7RANDOM.

■ To cancel random play

Press it again to cancel random playback mode.

Random playback mode is canceled when the disc is removed.

Press

PROG

(or

PROGRAM/MEMORY

)

when playback is stopped.

This unit turns into the program edit mode.

Press

ENTER

or the multi jog dial (J).

3 Press the numeric button(s) (

) (or rotate the multi jog dial (J)) to enter the track/file number you want to program, and then press

ENTER (or push the multi jog dial (J)).

4 Repeat step 3 until you finish programing all

desired tracks.

You can program up to 40 tracks/files.

• For MP3 or WMA files recorded on a disc, the time of the

file is not displayed.

• For MP3 or WMA files recorded on a disc, the number

assigned to each file corresponds to the file sequence in the disc, not in the individual folders.

5 Press and hold

PROG (or LPROGRAM/

MEMORY) to store the tracks you

programmed.

6 Press

(or

) to start playback in the

program playback mode.

■ To check or correct the programmed tracks/files

1 Press

PROG (or LPROGRAM/MEMORY) when this unit is in the program playback mode and playback is stopped.

This unit turns into the program edit mode.

Press

ENTER

or the

multi jog dial

(J)

repeatedly to check the program order.

3 To correct a programmed track/file, display

the track number to be corrected, and use the numeric button(s) (5) enter the track number to be newly programmed.

To delete an unwanted track, press HCLEAR (or

CLEAR).

Repeat playback

Note

Random playback

Note

Program playback

(Full repeat)

Normal playback

(Single repeat)

(Folder repeat, MP3/WMA disc only)

Notes

CD Program

P01 T008 01:23

Time of the trackProgrammed

track

Program

number

P02 T008 01:23

Elapsed time of the track

Currently played track

Program number

Example

Playback operations

10 En y The circled numbers and alphabets correspond to the ones on the attached sheet.

4 To finish checking or correcting the

programmed tracks, press and hold 6PROG (or LPROGRAM/MEMORY).

■ To exit program playback mode

To return to the normal playback mode, press 6PROG when this unit is in the program edit mode. To recall the programmed tracks, press 6PROG (or LPROGRAM/ MEMORY when playback is stopped and then press

(or

■ To clear the programmed order

Press and hold HCLEAR (or GCLEAR) when this unit is in the program playback mode and playback is stopped.

When you open the disc tray, the programmed order is cleared.

If your disc contains index numbers, you can start playback from any desired index number.

1 Press

INDEX.

2 Enter the index number using the numeric

button(s) (5).

■ To cancel the index search

Press EINDEX again.

The index system is a method for sub-dividing tracks into smaller divisions for easier search. If a disc contains an index, usually the

index mark ( ) is printed on the leaflet in the CD case.

• Not all discs have index numbers.

• If the selected index number does not exist in the disc, this unit starts playback from the last index of the disc.

• For some discs playback may start slightly prior to the actual designated index point.

This unit equips the iPod terminal on the top panel where you can directly station your iPod and control playback of your iPod using the supplied remote control.

1 Plug your iPod to the iPod terminal on the

top panel of this unit.

• Use this unit with the iPod dock adapter (supplied with your iPod or commercially available) appropriate for your iPod. Unless your iPod is firmly stationed in the terminal, audio signals may not be output properly.

• Do not connect any iPod accessories (such as headphones) to your iPod when it is stationed in the terminal.

2 Press

iPod (or press NINPUT repeatedly)

to select “iPod” and start playback.

If you plug your iPod while playing when any other source is selected as the input source (or even when this unit is in the standby mode), this unit automatically begins playback of the iPod.

3 Select the iPod playback mode.

1Press IFUNCTION and then 0ENTER (or

press KFUNCTION and then push the multi jog dial (J)).

2Press 0/ (or rotate the multi jog dial (J))

to select the desired mode and then press

ENTER (or press the multi jog dial (J)).

Note

Index search (Audio CD only)

Notes

Listening to your iPod™

Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod touch are supported.

Notes

Mode Playback

information

Playback control

Menu mode

Displayed on the display of this unit.

By the remote control of this unit

Click wheel mode

Displayed on your iPod.

By the remote control of this unit or your iPod

iPod dock adapter (supplied with your iPod or commercially available)

Playback operations

11 En

ENJOYING

PLAYBACK

4 Select a song you want to play back.

The buttons on the remote control correspond to the click wheel of iPod and you can control your iPod with them.

• You can switch the playback information display by pressing

INFO. For details, refer to “Switching the playback

information display” below.

• You can disconnect your iPod during playback.

Some features may not be compatible depending on the model or the software version of your iPod.

Press 9INFO repeatedly during playback.

Some special characters may not be shown properly.

■ Audio CDs

Elapsed time of the current track (Default)

Remaining time of the current track

Total time of the disc

Remaining time of the disc

Track name

Artist name

Disc title

Back to the default display

* Displayed only when you play a CD TEXT disc.

■ iPod (menu mode) or MP3/WMA files

Scrolling display (Default)

Elapsed time of the current file

Remaining time of the current file

File name

Song title

Artist name

Album name

Year

Comment

Back to the default display

*1 Scrolling display shows the song title, artist name, and album

name of the selected item in sequence.

*2 Displayed only when you play back MP3/WMA disc.

Note

Switching the playback information display

Note

ENTER

iPod

Remote control

Artists 9

Frankie Zipper

Item selected at the previous menu

Currently selected item

Example (menu mode)

T001 01:23

T001 -04:23

TTL T014 31:23

TTL T014 -30:00

Road to India

Frankie Zipper

Made-to-order

to-order-Franki

T0001 01:23

T0001 -04:23

Road-to-India

Road to India

Frankie Zipper

Made-to-order

2008

Live at LDFU

Listening to FM/AM broadcast

12 En y The circled numbers and alphabets correspond to the ones on the attached sheet.

Press

2TUNER

(or press

INPUT

repeatedly until “FM”, “AM”, or “DAB” is displayed).

2 Press

BAND (or

BAND

) repeatedly to

select “FM” or “AM”.

3 Press and hold

TUNING / .

This unit automatically searches and tunes into a station.

(When you control this unit with the front panel) Push the multi jog dial (J) repeatedly to select “Auto tune”, and then rotate the multi jog dial (J) to start searching.

• If the signal received from the station you want to select is weak, tune into it manually. Press

TUNING /

repeatedly or

select “Manual tune” in step 3 above and rotate the

multi jog dial

(

) to tune into the desired station.

• If the signal is weak and noise occurs during FM stereo reception, follow the procedure below to set this unit to the monaural mode.

1Press IFUNCTION and then press 0ENTER (or press

FUNCTION and then push the

multi jog dial

(J))

2 Press

(or rotate the

multi jog dial

(J)) to select

“

MONO

” instead of “STEREO

” and then press 0ENTER

(or

push the

multi jog dial (J)

Press and hold 6MEMORY (or LPROGRAM/ MEMORY) until “Auto memory” begins to flash.

• Up to 30 FM and 20 AM stations can be preset.

• “COMPLETE” is displayed when automatic preset

tuning is finished.

Automatic preset tuning overwrites the existing preset stations.

■ Presetting favorite broadcast stations manually

1 Tune into the station to be preset.

Refer to “Selecting broadcast stations” on this page.

2 Press

MEMORY (or LPROGRAM/

MEMORY).

« Within 4 seconds

Press FPRESET u / d (or rotate the multi jog dial (

J)) to select a desired preset

number.

« Within 4 seconds

Press 6MEMORY (or LPROGRAM/ MEMORY)

■ Deleting preset stations

Select the preset station and press HCLEAR (or

CLEAR). To delete all FM or AM preset stations, press

and hold HCLEAR (or GCLEAR).

Press FPRESET / repeatedly to select the desired preset station.

(When you control this unit with the front panel) Push the multi jog dial (J) repeatedly to select “Preset tune”, and then rotate the multi jog dial (J) to select the desired preset station.

You can also select the desired preset station using the numeric buttons (5).

1 Select the preset radio station you want to

edit the name.

2 Push and hold the multi jog dial (

) until

the cursor flashes.

Listening to FM/AM broadcast

Selecting broadcast stations

Presetting broadcast stations automatically

Note

Selecting preset stations

Editing the name of the preset radio stations

13 En

Listening to FM/AM broadcast

ENJOYING

RADIO

3 Rotate the multi jog dial (

) to select a character and then push it to confirm your selection.

• You can enter alphabets (A to Z) and/or numbers

(0-9).

• To enter a blank space, select the blank between

“Z” and “0”.

• To delete the input character, press GCLEAR.

• To delete all characters, press GCLEAR for more

than 3 seconds.

4 Repeat step 3 until you finish editing.

5 Push and hold the multi jog dial (

1 Tune into an FM station.

2 Press

INFO repeatedly to select desired

information and wait until blinking stops.

The mode changes as follows:

PROGRAM SERVICE

The name of the station being received is displayed. The frequency will be displayed, if no program service data is found.

PROGRAM TYPE

The program type is displayed (refer to the table on this page).

RADIO TEXT

Information about the program being received is displayed using a maximum of 64 alphanumeric characters. The mode is automatically switched to PROGRAM SERVICE mode, if no radio text data is found.

CLOCK TIME

The current time is displayed and updated every minute. “CT NONE” is displayed if no time data is found.

Normal display

• The available Radio Data System information types vary depending on the station.

• If the signal transmission of the FM Radio Data System station is too weak, this unit may not be able to receive Radio Data System information completely. In particular, RADIO TEXT information uses a lot of bandwidth, so it may not be available even when other modes are selectable.

Program type

Receiving radio data system information

Notes

News News Current Affairs Current Affairs Information Information Sport Sport Education Education Drama Drama Cultures Cultures Science Science Varied Speech Varied Speech Pop Music Pop Music Rock Music Rock Music Easy Listening Easy Listening Light Classics Light Classics Serious Classic Serious Classic Other Music Other Music Weather & Metr Weather & Meteorology Finance Finance Children's Prog Children’s Program Social Affairs Social Affairs Religion Religion Phone In Phone In Travel & Tourin Travel & Touring Leisure & Hobby Leisure & Hobby Jazz Music Jazz Music Country Music Country Music National Music National Music Oldies Music Oldies Music Folk Music Folk Music Documentary Documentary Alarm Test Alarm Test Alarm-Alarm! Alarm-Alarm!

Listening to DAB broadcast

14 En y The circled numbers and alphabets correspond to the ones on the attached sheet.

1 Press

BAND (or EBAND) repeatedly to

select “DAB”.

When you select “DAB” for the first time, this unit automatically scans for DAB services in your area, it takes about 90 seconds to finish scanning.

Press

repeatedly and then press

0ENTER

(or rotate and push the

multi jog

dial

(J)) to select the desired channel.

• When the selected DAB service has a secondary service, the SECONDARY indicator flashes in the front panel display for 5 seconds.

• When the selected DAB service is a secondary DAB service, the SECONDARY indicator lights up.

• “Off air” appears when this unit cannot receive specified DAB service.

■ Displaying a signal strength

Use this feature to adjust the positioning of the DAB antenna and this unit. It is effective at maximizing the DAB reception capability.

1 Press

FUNCTION (or KFUNCTION)

while listening to a DAB station.

2 Press

/ repeatedly and then press

ENTER (or rotate and push the multi jog

dial (J)) to select “Manual tune”.

3 Press

ENTER.

Press again to return to the normal display.

■ Updating the DAB channel list

1 Press

FUNCTION (or KFUNCTION)

while listening to a DAB station.

2 Press

/ repeatedly and then press

ENTER (or rotate and push the multi jog

dial (J)) to select “Full Scan” or

“Local Scan”.

• Local Scan: This unit scans specified ranges in

band III.

• Full Scan: This unit scans all ranges in band III. If new DAB channels are found, they are added to the

DAB channel list.

■ Selecting preset DAB stations

You need to preset DAB stations in advance. See “Presetting favorite broadcast stations manually” on page 12. You can preset up to 99 stations.

1 Press

FUNCTION (or KFUNCTION)

while listening to a DAB station.

2 Press

/ repeatedly and then press

ENTER (or rotate and push the multi jog

dial (J)) to select “Preset tune”.

3 Press

/ repeatedly and then press

0ENTER

(or rotate and push the multi jog

dial (J)) to select the station you want to

listen to.

Listening to DAB broadcast

Listening to DAB stations

Note

Advanced DAB operations

15 En

Listening to DAB broadcast

ENJOYING

RADIO

■ Rearranging the channel list

1 Press

FUNCTION (or KFUNCTION)

while listening to a DAB station.

2 Press

/ repeatedly and then press

0ENTER

(or rotate and push the multi jog

dial (J)) to select “Station order”.

3 Press

/ repeatedly and then press

ENTER (or rotate and push the multi jog

dial (J)) to select “Alphanumeric” or

“Ensemble”.

• Alphanumeric: Channels are listed in

alphanumeric order (0-9, A-Z) by the first letter of the station name.

• Ensemble: This option will list active stations

(stations that can be received by this unit) at the top of the channel list. Channels that are in the list but have no service in your area are listed at the bottom of the channel list.

■ Compressing the dynamic range

Some DAB broadcasters transmit a wide dynamic range (enabling high quality sound), accompanied by dynamic range control data. The dynamic range control can be used to compress the dynamic range of the broadcast, making softer sounds easier to hear.

1 Press

FUNCTION (or

FUNCTION

)

while listening to a DAB station.

2 Press

/ repeatedly and then press

0ENTER

(or rotate and push the multi jog

dial (J)) to select “Dynamic Range”.

3 Press

/ repeatedly and then press

0ENTER

(or rotate and push the multi jog

dial (J)) to select from “0”, “1/2”, or “1”.

• 0: This unit does not compress the dynamic range.

• 1/2: Medium dynamic range compression.

• 1: Maximum dynamic range compression.

Press

9INFO

repeatedly to select the desired

information. Dynamic label segment

Program type

Ensemble name

Current date and time

Audio mode and bitrate

Channel name/frequency

Signal error rate (0-99)

The lower the figure, the better the quality of the received broadcast.

Software version

Back to dynamic label segment

Switching the DAB information

TROUBLESHOOTING

Troubleshooting

If there is any problem with this unit, check the following items. If you cannot solve your problem with the following remedies or if your problem is not listed below, turn off and unplug the unit, then consult the nearest authorized Yamaha dealer or service center.

General

Problem Cause Solution Refer to

Power turns on but immediately shuts off.

The speakers make no sound.

Sound suddenly turns off.

Sound is small on one side.

The volume does not increase or sounds are distorted.

This unit does not operate properly.

Sound played on this unit cannot be recorded with an external recorder.

The clock setting has been cleared.

A digital equipment or high frequency equipment near this unit produces noises.

The power cable may be connected improperly.

The speaker cable may be shorted. Make sure all speaker cables are connected

This unit may receive a strong electrical shock such as from a lightening bolt or excessive static electricity.

The volume may be set to the minimum level.

The mute function may be enabled. Cancel the mute function. P. 6 The input source may be incorrect. Select the correct input source. P. 6

The cables may be connected improperly. Make sure all cables are connected properly. P. 4, 5 The disc loaded into this unit may be not

compatible. The sleep timer might be set. Turn on this unit and play the source again. P. 6

The cables may be connected improperly. Make sure all cables are connected properly

The power of the equipment connected to the output jacks of this unit may be turned off.

This unit may receive a strong electrical shock, such as from a lightening bolt or excessive static electricity, or drop in power supply.

You may be trying to make a digital recording with an analog source.

The power to this unit may have been lost for more than four minutes.

This unit may be placed close to the digital equipment or high-frequency equipment.

Make sure the power cable is plugged into the outlet firmly.

properly.

Set this unit to the Standby mode, then disconnect the power cable. Wait for about 30 seconds, then connect the power cable and turn on this unit.

Adjust the volume level. P. 6

Make sure you use a disc supported by this unit.

and adjust the speaker balance. Turn on the power of the equipment

connected to the output jacks of this unit.

Set this unit to the Standby mode, then disconnect the power cable. Wait for about 30 seconds, then connect the power cable and turn on this unit.

Use proper audio sources. P. 6

Make sure the power cable is plugged into outlet firmly, then set the clock again.

Place this unit further away from such equipment.

P. 5

P. 4

—

P. 1 9

P. 4 , 6

—

P. 5

—

16 En

17 En

Troubleshooting

APPENDIX

Disc playback

Problem Cause Solution Refer to

Some button operations do not work.

Some discs do not support certain functions of this unit.

—

Playback does not start immediately

when pressing

(or

The disc may not be set in the disc tray properly.

Set the disc in the disc tray properly. P. 8

The disc may be dirty. Wipe the disc clean. P. 19 The disc loaded into

this unit

may be not

compatible with this unit.

Make sure you use a disc supported by this unit.

P. 1 9

If this unit is moved from a cold place to warm one, condensation may be form on the disc reading lens.

Wait for one to two hours, then try again. —

The message “No Disc” appears even though a disc is set.

The disc loaded into

this unit

may be not

compatible with this unit.

Make sure you use a disc supported by this unit.

P. 1 9

iPod™ playback

Problem Cause Solution Refer to

“Unplugged” is displayed and the iPod is not recognized.

The iPod is not connected securely. Remove the iPod and plug it again. P. 10

Use a proper iPod dock adapter supplied with your iPod.

—

18 En

Troubleshooting

Radio reception

Problem Cause Solution Refer to

The preset tuning function does not work.

The preset station settings may have been erased.

Preset radio stations again. P. 12

The preset station settings have been cleared.

The power to this unit may be lost more than a week.

Make sure the power cable is plugged into outlet firmly, and then preset the stations again.

P. 5, 12

The auto tuning function does not work.

The antenna may be connected improperly.

Make sure the antenna is connected properly. P. 5

The radio station you selected may be far away from your area or radio wave reception is weak in your area.

Try manual tuning to increase the signal quality.

P. 1 2

(FM) Too much noise is generated during stereo broadcast.

The FM antenna may be connected improperly.

Make sure the FM antenna is connected properly.

P. 5

The radio station you selected may be far away from your area or radio wave reception is weak in your area.

Try manual tuning to increase the signal quality or use a commercially available multi-channel outdoor antenna.

P. 5, 12

Switch the reception mode of this unit to monaural.

P. 1 2

(FM) Even with an outdoor antenna, radio wave reception is weak (audio is distorted).

Multipath reflection or other radio interferences may occur.

Change the height, direction, or placement of the antenna.

—

(AM) Too much noise is generated.

The noises may be generated from atmospheric electricity, lightening, fluorescent lights, motors, or thermostat electric devices.

Connect an outdoor antenna and establish better grounding to decrease noises. However, it is difficult to eliminate these types of noises.

P. 5

If too much noise is generated especially in the evening, this unit may be placed close to a TV.

Place this unit further away from a TV. —

(DAB) Cannot tune into any DAB stations.

There is no DAB coverage in your area. —

(DAB) The service reception is weak.

The positioning of the indoor DAB antenna and/or the unit is not optimal for DAB reception.

Display the signal strength and find the best position for the DAB antenna and this unit.

P. 1 4

Remote control

Problem Cause Solution Refer to

The remote control does not work for operating this unit.

The remote control may be operated outside the remote control operation range.

Use the remote control within the operation range.

P. 3

The remote control sensor on this unit may be exposed to direct sunlight or lighting (inverted fluorescent lamps).

Change the lighting or the orientation of this unit.

—

The batteries may be worn out. Replace the batteries with new ones. P. 5

19 En

APPENDIX

This unit is designed for use with audio CD, CD-R, and CD-RW. Also, this unit can play back 8 cm compact discs.

This unit can play back discs bearing any of the logo marks above. A disc logo mark is printed on the disc and the disc jacket.

Do not load any other type of disc into this unit. Doing so may damage this unit.

This unit can play back the following data discs:

• MP3 files, recorded on CD-R/RW (fs 44.1, 48 kHz/32, 64, 96, 128, 192, 256, or 320 kbps and variable bit encoded MP3 files (CBR and VBR))

• WMA files, recorded on CD-R/RW (fs 44.1 kHz/192 kbps or less and variable bit encoded WMA files (CBR and VBR))

• ISO 9660 for CD-R/RW

• CD-R/RW cannot be played back unless finalized. Finalize

means to process the information stored in the disc so as to make it compatible with other players.

• Use reliable discs. Some discs cannot be played back

depending on the disc characteristics or recording conditions.

• Do not use any non-standard shaped discs such as a heart-

shaped disc.

• Do not use discs with many scratches on their surface.

• Copyright-protected WMA files cannot be played back on this

unit.

• The sampling rate 48 kHz is downsampled to 44.1 kHz for

playback.

• Do not touch the surface of the disc. Hold a disc by its edge (and the center hole).

• Do not leave a disc in the disc tray when not playing.

• Do not use a pencil or pointed marker to write on the disc.

• Do not put a tape, seal, glue, or other attachments on a disc.

• Do not use a protective cover to prevent scratches.

• Do not use a disc that has a printable surface using a commercially available label printer.

• Do not expose a disc under direct sunlight, high temperature, high humidity, or a lot of dust.

• If a disc becomes dirty, wipe it with a clean, dry cloth from the center out to the edge. Do not use record cleaner or paint thinner.

• To avoid malfunction, do not use a commercially available lens cleaner.

• Do not insert more than one disc into the disc tray at one time. This can cause damages to both this unit and the discs.

• Do not use an 8 cm-disc adapter. Load an 8 cm (3 inch) disc as it firmly sits on the disc tray. If loaded improperly, the disc can impede the disc tray opening/closing.

• Do not insert fingers when closing the disc tray. This can lead to injury.

• Do not insert any foreign objects into the disc tray.

• Do not insert a cracked, warped, or glued disc.

Notes on discs

Disc information

Note

Notes

Handling a disc

Note

Do not use any lens cleaners as they may be a cause of malfunction.

Caution

GLOSSARY

20 En

■ MP3

One of the audio compression methods used by MPEG. It employs the irreversible compression method, which achieves a high compression rate by thinning out the data of hardly audible part to human ears. It is said to be capable of compressing the data quantity by about 1/11 (128 kbps) while maintaining a similar audio quality to music CD.

■ WMA

An audio compression method developed by Microsoft Corporation. It employs the irreversible compression method, which achieves a high compression rate by thinning out the data of hardly audible part to human ears. It is said to be capable of compressing the data quality by about 1/22 (64 kbps) while maintaining a similar audio quality to music CD.

■ iPod

iPod is a portable media player designed and marketed by Apple Inc. iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

■ DAB

DAB (Digital Audio Broadcasting), also known as digital radio, is a new way of radio broadcasting. DAB is broadcast using digital signals instead of analog signals, resulting in near CD-quality sound. Analog signals (i.e. AM/FM) are susceptible to interference (i.e. distortion and noise) caused by electrical equipment, weather conditions, tall buildings, mountains, etc.; digital signals are not. Thus, with DAB, there is virtually interference-free reception and no hiss or crackle.

Another advantage of DAB is that a large amount of information can be carried within the digital signal. DAB is broadcast in blocks of data called ensembles (also known as multiplexes). Several radio programs (called primary services) can be broadcast simultaneously in each ensemble. This means that you can choose between several radio programs within one frequency.

In addition to the audio signal, secondary services are also broadcast and displayed on this unit’s front panel display. Part of the secondary services are text data information called DLS (Dynamic Label Segment). For more information, see page 15.

With DAB, there is no need to remember channel frequencies, either. All broadcasts are selected by simply selecting the service name.

• You can tune the range of channels are 10A to 12D in UK.

• The sound quality and PAD/SI information are controlled by the DAB broadcaster, not this unit. Not all DAB broadcasters transmit PAD/SI information.

• DAB signals are broadcast in Band-III (174 – 240 MHz).

Glossary

Notes

Ensemble

(Multiplex)

Primary services

Audio signal and Secondary service

21 En

APPENDIX

■ Audio section

• Minimum RMS output power per channel

......................................... 25 W + 25 W (6 Ω , 1 kHz, 0.1% THD)

• Input sensitivity/impedance

AUX ...................................................................... 350 mV/47 kΩ

• Frequency response

CD etc. ................................................. 20 Hz to 20 kHz, ±0.5 dB

• Total harmonic distortion

CD etc. 1kHz ...................................................................... 0.03%

• Signal to noise ratio (IHF-A network)

CD etc. (350 mV, input shorted) .......................................... 98 dB

■ FM section

• Tuning range (50 kHz steps) .......................... 87.50 to 108.00 MHz

• Signal to noise ratio (mono) ................................................... 65 dB

• Sensitivity (S/N 30 dB) ...................................................... 1.0 µV/m

■ AM section

• Tuning range (9 kHz steps) .................................... 522 to 1629 kHz

• Signal to noise ratio ................................................................ 35 dB

• Sensitivity ......................................................................... 600 µV/m

■ DAB section

• Tuning range (BAND III) ............................. 174 MHz to 240 MHz

• Input ....................................................................... 50 Ω , (nominal)

• Sensitivity .......................................................................... –96 dBm

• Selectivity ......................................................................... 35 dB typ.

• Audio out ................................................................ Stereo, 2.0 Vp-p

• Digital out ................................................... 24 bit/48 kHz resolution

■ CD player section

• Signal to noise ratio .............................................................. 110 dB

• Total harmonic distortion ..................................................... 0.005%

• Separation .............................................................................. 100 dB

■ General

• Power supply ......................................................... AC 230 V, 50 Hz

• Power consumption .................................................................. 80 W

• Standby power consumption ................................................... 0.5 W

• Laser pick up

Material............................................................................GaAlAs

Wavelength ............................................................... 790 ±25 nm

Laser output ............................................................. 8 mA or less

• Dimensions (W x H x D) .............................. 210 x 109 x 359.5 mm

• Weight ................................................................................... 4.65 kg

* Specifications are subject to change without notice.

Specifications

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

ADVARSEL - USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅKING.

VAROITUS! - SUOJAKOTEL OA EI SAA AVATA. LAITE SISÄLTÄÄ LASERDIODIN, JOKA LÄHETTÄÄ (NÄKYMÄTÖNTÄ) SILMILLE VAARALLISTA LASERSÄTEILYÄ.

ADVARSEL - USYNLING LASERBESTRÅLING NÅR DENNE DELEN ER ÅPEN OG SIKKERHETSSPERREN ER UTKOBLET. UNNGÅ UTSETTELSE FOR STRÅLING.

CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.

VORSICHT! UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL GEÖFFNET UND WENN SICHERHEITSVER RIEGELUNG ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!.

VARNING - OSYNLING LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG.

Limited Guarantee for European Economic Area (EEA) and Switzerland

Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).

The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been discontinued or is considered uneconomic to repair.

Conditions

1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a

statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the product may be returned at the customer’s expense.

2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.

3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.

4. The following are excluded from this guarantee: a. Periodic maintenance and repair or replacement of parts due to normal wear and tear. b. Damage resulting from:

(1) Repairs performed by the customer himself or by an unauthorised third party. (2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to

ensure the product is adequately packaged when returning the product for repair.

(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper

use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in the country where it is used.

(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control. (5) Defects of the system into which this product is incorporated and/or incompatibility with third party products. (6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety

standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.

(7) Non AV (Audio Visual) related products.

(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident.)

5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.

6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the

product.

7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.

This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising from their sales/purchase contract.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

Printed in China

CQX1A1390Z

The circled numbers and alphabets correspond to those in the Owner’s Manual.

常圆圈的数字和文字与说明书中的同类数字和文字相对应。

■ Front panel/ 前部面板 /

CRX-D430/CRX-430

BTJ

イラストに記載されている数字やアルファベットは、取扱説明書中のキーなどに付記されている数字やアルファベットに対応しています。

フロントパネル

POWER

STANDBY/ON

PHONES

TIME

MODE

FUNCTION

PROGRAM

/MEMORY

BAND

VOLUME

INPUT

CLEAR

TUNING/PRESET/TIME

PUSH-ENTER

ABC DEFG

HI J KL M N O

00_sheet_CRX-D430_BTJ.book Page 1 Thursday, Sep tember 18, 2008 1:27 PM

Black process 45.0° 240.0 LPI

■ Remote control/ 遥控器 /

リモコン

STANDBY/ON

2 3

6 7

SLEEP

AUX

TIMER

456

789

RANDOM FUNCTION

DIMMER INDEX BAND

MEMORY

PROG

INFO

iPod

CLEAR

A-BREPEAT

TUNER

PRESET

TUNING

H I

ENTER

FOLDER VOLUME

MUTE

Printed in China

CQE1A423Z

Yamaha CRX-D430 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual