Yamaha CRW8824SX User Manual
CD-R/RW Drive
CD-R/RW Drive
CRW8824SX
CRW8824SX
SERIES
SERIES
OWNER’S MANUAL
OWNER’S MANUAL
BEDIENUNGSANLEITUNG
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
MANUAL DE INSTRUCCIONES
FCC INFORMATION
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party: Yamaha Corporation of America
Address: 6600 Orangethorpe Ave.
Buena Park, CA 90620
Telephone: 714-522-9011
Fax: 714-228-3913
Type of Equipment: CD Recordable/Rewritable Drive
Model Name: CRW8824SX
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that
may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product
in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause
interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is found to be the source of interference, which can be determined
by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America,
6600 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.
LASER INFORMATION
Laser Diode Properties
Material: GaAlAs
Wavelength: 780-787 nm
Emission Duration: Continuous
Laser Output Power: Less than 44.6 µW*
* This output is value measured at a distance 200
mm from the objective lens surface on the optical
pick-up block.
ANSI Class : Class 1
Eigenschaften der Laserdiode
Material: GaAIAs
Wellenlänge: 780-787 nm
Strahldauer: Kontinuierlich
Laser-Ausgangsleistung: Weniger als 44,6 µW*
* Diese Leistung wurde in einem Abstand von 200
mm ab der Linsenoberfläche des optischen
Sensorblocks gemessen.
ANSI-Klasse: Klasse 1
Caractéristiques de la diode laser
Matériau: GaAIAs
Longueur d'onde: 780-787 nm
Durée d'émission: Continue
Puissance de sortie du laser: Moins de 44,6 µW*
* Cette valeur de sortie a été mesurée à une
distance de 200 mm depuis la lentille sur le bloc
capteur optique.
Classe ANSI: Classe 1
Propiedades del diodo láser
Material: GaAlAs
Longitud de onda: 780-787 nm
Duración de la emisión: Continua
Potencia de salida láser: Menos de 44.6 µW*
* Esta salida es el valor medido a una distancia de
200 mm de la superficie del objetivo del bloque
captor óptico.
Clase ANSI : Clase 1
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
ACHTUNG
Halten Sie sich beim Bedienen und Einstellen der
Bedienungselemente sowie bei der Bedienungsabfolge
an die Anleitung, da sonst gefährliche Strahlen austreten
können.
ATTENTION
L’emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d’éventuelles
radiations pouvant être dangereuses.
PRECAUCION
El usar los controles o ajustar o realizar procedimientos
diferentes a los especificados aquí resultará en
peligrosas exposiciones a la radiación.
VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL EST OUVERT.
EVITEZ TOUTE EXPOSITION AU FAISCEAU.
CD-R/RW Drive
CD-R/RW Drive
CRW8824SX
CRW8824SX
SERIES
SERIES
English
OWNER’S MANUAL
i
SAFETY PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
These precautions explain how to use the device correctly and safely, thereby preventing injury to
yourself or to others. This section has been sub-divided into a WARNING section and a CAUTION
section, according to the likelihood and nature of any potential injuries or damage inflicted. They
relate to your personal safety, and also help you minimize the risk of damaging the device. Please
read these sections carefully before proceeding.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even
death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions
include, but are not limited to, the following:
● Do not open the device or attempt to disassemble or modify it.
Otherwise, there is an increased risk of electrical shock or fire. The device contains no userserviceable parts. If it appears to be malfunctioning, have it inspected by qualified service personnel.
● Do not look inside the device.
If you expose your eyes to the laser inside the device, you risk losing your vision.
● Do not insert fingers or foreign objects into the device.
Otherwise, there is an increased risk of personal injury, electrical shock, damage to the device or fire.
Please take particular care if small children are present.
● Do not expose the device to rain, use it near water or in damp or wet conditions or place containers
on it containing liquids which might spill into any openings.
Otherwise, there is an increased risk of electrical shock, fire or personal injury.
● Follow the Owner’s Manual carefully.
Otherwise, there is an increased risk of personal injury, electrical shock, fire or damage to the unit.
Follow the correct procedure when setting up the device.
● If unusual smells, sounds or smoke emanate from the device or if liquids enter the device, switch
the computer off immediately and unplug it from the power outlet.
Otherwise, there is an increased risk of electrical shock, fire or damage to the device. Return the
device immediately to the store at which it was purchased or alternatively, to the nearest Yamaha
Service Center (listed at the back of this manual).
● Make sure the computer is electrically grounded
Otherwise, there is an increased risk of electrical shock.
● When opening up the computer, always unplug the computer from the electrical outlet. Do not
touch the plug with wet hands.
Otherwise, there is an increased risk of electrical shock.
● When used in a fan-cooled system, the drive should not be exposed to temperatures outside the
range 5 ~ 35°C (41 ~ 95°F).
ii
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you
or others, or damage to the instrument or other property. These precautions include, but are not
limited to, the following:
● Always unplug the computer from the electrical outlet if it will not be used for a prolonged period of
time or if there is a risk of lightning.
Otherwise, there is an increased risk of electrical shock, short-circuiting or fire.
● Do not expose the device to excessive heat or vibrations or extreme cold or heat (such as in direct
sunlight or near a heater).
Otherwise, the front panel may become disfigured or the internal components may be damaged.
● Do not use the device near other electrical products such as televisions, radios or speakers.
Otherwise, this may cause interference which can affect the proper operation of those other products.
● Do not place the device in an unstable position.
Otherwise, it may accidentally fall down and be damaged or cause personal injury.
● Mount the device horizontally.
Otherwise, written data may be destroyed. Set the device up according to the instructions in the
Owner’s Manual.
● Always remove the disc from the tray before transporting the device.
Otherwise, written data may be destroyed.
● When cleaning the device, never use benzene, paint thinners, detergents or chemical-impregnated
wiping cloths. Also, do not place vinyl, plastic or rubber objects on the device.
Otherwise, the device may be damaged or its front panel may become discolored. Use a soft, dry
cloth to wipe the device.
● Do not rest your weight on or place heavy objects on the device and do not use excessive force on
the buttons, switches or connectors.
Otherwise, there is an increased risk of damage to the device or personal injury.
● Do not listen to audio with headphones at high volume and for prolonged periods of time.
Otherwise, there is an increased risk of hearing loss.
● Before using the device, set the volume dial to its lowest setting.
Otherwise, sudden bursts of sound can cause hearing loss.
● Do not place the device near sources of magnetic interference, such as computer displays.
Magnetic interference can affect the operation and stability of the device.
● Have the device serviced regularly.
Otherwise, dust can build up inside the device, increasing the risk of fire or damage. For information
about servicing charges, contact the store at which the device was purchased or alternatively, the
nearest Yamaha Service Center (listed at the back of this manual). The device should be serviced
about once a year.
iii
■ About CD-R/RW discs
Please read the following regarding the handling of CD-R/RW discs.
1. Do not expose discs to excessive heat or vibrations or extreme cold or heat (such as in
direct sunlight or near a heater).
2. Do not touch disc surfaces.
When handling a disc, hold it by its edges.
3. Remove dust and dirt from disc surfaces.
Use air-based dust removers. The surfaces may be scratched if wiped with a dry cloth.
4. Do not write or stick labels on disc surfaces except where indicated.
5. Do not clean discs with chemicals or detergents.
6. Do not bend or drop discs.
1. The information contained in this manual is subject to change
without prior notice.
2. All trademarks contained in this manual belong to their respective
owners.
3. Yamaha does not bear any responsibility for any outcome as a
result of using this device.
4. Reproduction of this manual, either in part or in full, is expressly
forbidden.
■ Precautions for Transportation
Before transporting the device, always put it in its original box. If the device is transported
without adequate packing, the internal components can become damaged and cause the
device to malfunction.
■ Distributing Discs
When writing important data or preparing data for distribution to others, make sure that the
disc can be read properly before writing duplicates.
■ Copyrights
When writing to CD-R/RW, make sure that you are not infringing any copyrights. It is illegal
to copy audio CDs for non-personal use. When backing up software, please make sure that
you are not infringing any software copyrights for that product.
■ WARRANTY
YAMAHA AND SUPPLIERS ACCEPT NO LIABILITY FOR THE LOSS OF ANY DATA OR
ANY PROBLEMS CAUSED AS A RESULT. AS A PRECAUTION, IT IS RECOMMENDED
THAT THE DISCS ARE TESTED AFTER THEY HAVE BEEN WRITTEN TO.
FURTHERMORE, UNDER NO CIRCUMSTANCES DOES YAMAHA AND SUPPLIERS
GUARANTEE THE RELIABILITY OF THE DISCS.
iv
Table of Contents
Setup Flowchart .................................................................. 1
Windows Users ............................................................................... 1
Macintosh Users ............................................................................. 2
Introduction ....................................................................... 3
Features of the CRW8824SX Drive ................................................. 3
System Configuration ............................................................ 4
Computer ........................................................................................ 4
Software .......................................................................................... 5
Discs ................................................................................................ 6
Tool ................................................................................................. 7
Front and Rear of Unit ........................................................... 8
Front Panel ..................................................................................... 8
Rear Panel ....................................................................................... 9
Installation ....................................................................... 10
First Steps ..................................................................................... 10
Setting Up The CRW8824SX Drive ............................................ 12
Installing a SCSI Adapter Card ..................................................... 13
Connecting the Drive .................................................................... 16
Verifying the Hardware Installation .............................................. 20
Operation ......................................................................... 22
Loading a Disc........................................................................ 22
Ejecting the Disc .................................................................... 22
Manually Ejecting a Disc in an Emergency............................ 23
Troubleshooting ................................................................. 24
Appendix .......................................................................... 27
Writing Modes .............................................................................. 27
About the Firmware ...................................................................... 29
LED Indicator Messages................................................................ 30
CRW8824SX Specifications .......................................................... 31
Index............................................................................... 33
©2000 Yamaha Corporation. All Rights Reserved.
This document may not, in whole or in part, be copied, photocopied,
reproduced, translated, transmitted or reduced to any electronic medium of
machine readable form without prior consent in writing from Yamaha.
Windows is a registered trademark of Microsoft Corporation.
Macintosh is a registered trademark of Apple Computer, Inc.
All other trademarks are the property of their respective companies.
v
24X: 3,600 KB/sec
Setup Flowchart
These flowcharts show the procedure for setting up the CRW8824SX drive. For
easy cross-referencing, the relevant pages in this manual are also given.
Windows Users
STEP
Do you have a SCSI adapter
card?
1
YES
STEP
Check that the SCSI adapter
card is recognized correctly
2
Go to Control Panel | System | Device
Manager tab. Double-click on SCSI
controllers to check that the adapter card is
recognized correctly by the computer’s OS.
Set up the CRW8824SX drive
STEP
1. Set the switches at the rear of the drive.
3
(P.10, 11)
2. Connect the SCSI and power cables,
then switch the drive on. (P.16-18)
STEP
Check that the CRW8824SX drive
is recognized correctly (P.20)
4
Go to Control Panel | System | Device
Manager tab. Double-click on CDROM
to check that the drive is recognized
correctly by the computer’s OS.
NO
STEP
Obtain a SCSI adapter card
1-1
Recommended models:
Adaptec AHA-2940-series (PCI)
Install the SCSI adapter card
STEP
Read this manual and insert the
1-2
SCSI card into the appropriate
PCI slot on the computer.
Install the CD writing software
STEP
For details about how to install the
software, refer to the documentation that
5
came with it.
Start using the CRW8824SX
STEP
drive!
6
Use the drive to create audio CDs, to
back up data on your hard disk, or for
whatever purpose suits your needs.
1
Macintosh Users
Setup Flowchart
STEP
Does your Macintosh have
a built-in SCSI connector?
1
YES
Set up the CRW8824SX drive
STEP
1. Set the switches at the rear of the drive.
2
(P.10, 11)
2. Connect the SCSI and power cables,
then switch the drive on. (P.16-18)
STEP
Check that the CRW8824SX
drive is recognized correctly
3
Use the Apple System Profiler and check
that the drive is recognized correctly.
STEP
Install the CD writing
software
4
For details about how to install the
software, refer to the documentation
that came with it.
Start using the CRW8824SX
STEP
drive!
5
Use the drive to create audio CDs, to
back up data on your hard disk, or for
whatever purpose suits your needs.
NO
STEP
Obtain a SCSI adapter card
1-1
Recommended model:
Adaptec PowerDomain 2930U (PCI)
Install the SCSI adapter card
STEP
Read this manual and insert the
1-2
SCSI card into the appropriate
PCI slot on the computer.
2
Introduction
Features of the CRW8824SX Drive
High speed
CD-R/RW discs can be written/rewritten at up to 8X speed. For example, an
audio CD (74 minutes/650 MB) can be created in approximately 10 minutes.
Data reading at up to 24X speed is supported.
CD TEXT support
CD TEXT is a capability that adds text data to an audio CD. Information such as
the song name or artist name can be recorded using writing software. The text
data on the disc you create can be displayed by a CD player that is compatible
with CD TEXT.
Wide compatibility
To ensure compatibility with a wide range of discs, technical data has been
exchanged with major disc manufacturers. 700 MB discs are also supported.
High-fidelity audio
Writing software can be used to extract digital audio data at up to 24X speed.
(This data can be saved in WAVE format in a Windows environment, or in AIFF
format in a Macintosh environment.) Digital sound can be recorded with
complete fidelity even when writing at 8X speed.
Reliable writing
Yamaha’s proprietary Pure-Phase Laser System*1 improves jitter values*2 to allow
the signal to be recorded accurately. In addition, the 4 MB buffer memory and
Running OPC
*3
technology further enhance reliability.
*1. Pure-Phase Laser System (patent applied for)
Technology that reduces phase interference of the laser beam, so that it shines accurately on the disc.
*2. Jitter value
An important measure of recording quality. This has been improved 25% compared with Yamaha models
not using this technology.
*3. Running OPC
CD-R/RW discs vary by manufacturer in their recording characteristics, and the laser output required to
write data differs by disc. Running OPC is technology that solves this problem by automatically adjusting
the output of the laser according to the material of the disc on which data is being written.
3
System Configuration
In order to use the CRW8824SX drive, your computer system will need to meet
the following set of requirements.
Computer
The minimum system requirements for using the CRW8824SX drive are as
follows:
● For PC/AT-compatible computers:
OS: Windows 95/98/98SE (Second Edition), Windows NT4.0 with Service
Pack 3 or later, Windows 2000.
CPU: Pentium-class or better, 200MHz or faster.
RAM: 32MB (64MB recommended).
● For Macintosh computers:
OS: Mac OS 8 to Mac OS 9.
CPU: PowerPC G3/300 or better.
RAM: 32MB (64MB recommended).
CD-ROM drive.
● A spare PCI expansion slot for a SCSI card (if one hasn’t been installed yet).
● A SCSI card to connect SCSI devices (including the CRW8824SX) to your
computer. Make sure it has a D-sub half-pitch 50-pin pin-type external
connector. Yamaha recommends any of Adaptec’s AHA-2940-series cards
(PCI slot).
n Many Apple Macintosh computers have built-in SCSI connectors. However, if your
Macintosh does not have a built-in SCSI connector, you will need to obtain a PCI
bus SCSI adapter card. (Yamaha recommends Adaptec’s PowerDomain 2930U card.)
n For details about how to install the SCSI adapter card, refer to the documentation
that came with it.
4
System Configuration
Software
The software requirements for using the CRW8824SX drive are as follows:
● CD writing software. This software must support the CRW8824SX drive for
writing to CD-R or CD-RW.
n For details about how to install and use the software, refer to the documentation
that came with it.
n Please verify the settings for your system setup (hardware, OS, etc.).
● When temporarily storing data on a hard disk prior to writing to CD-R/RW,
you will need an extra area of 50 ~ 100MB free hard disk space. When
creating an image file of the data on hard disk before writing to CD-R/RW, you
will need as much hard disk space as the original data, plus an extra 50 ~
100MB. However, this extra area is not needed when backing up directly from
CD-ROM.
n Data is written to disc much more reliably when writing from an image file,
eliminating the likelihood of errors occurring. Furthermore, this solution is ideal
when making multiple copies of discs since the original data is backed up to hard
disk as an image file.
5
Loading...