BG
RX-E100 / CDX-E100
Natural Sound Stereo Receiver/Natural Sound Compact Disc Player
Récepteur Stéréo/Lecteur Compact Disque
RL
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
SUPPLIED ACCESSORIES • After unpacking, check that the following parts are contained.
ACCESSOIRES FOURNIS • Après le déballage, vérifier que les pièces suivantes sont incluses.
MITGELIEFERTES ZUBEHÖR
• Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
MEDFÖLJANDE TILLBEHÖR• Kontrollera efter det apparaten packats upp att följande delar finns med.
ACCESSORI IN DOTAZIONE •
Verificare che tutte le parti seguenti siano contenute nell’imballaggio
dell’apparecchio.
ACCESORIOS INCLUIDOS • Desembale el aparato y verificar que los siguientes accesorios están en la caja.
BIJGELEVERDE ACCESSOIRES
• Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
<RX-E100>
• Remote control
• Télécommande
• Fernbedienungseinheit
• Fjärrkontrollen
• Telecomando
• Mando a distancia
• Afstandbediening
SLEEP
A
REP
D
PEAK
MD CD
MD REC
MODE START
TIME
B
RNDM
MODE
VOLUME
TAPE
AUX
TUNER
PRESET
PTY SELECT
TAPE
DUBBING
• AM loop antenna
• Antenne cadre AM
• MW-Rahmenantenne
• AM ramantenn
• Antenna AM ad uso interno
• Antena de cuadro de AM
• AM ringantenne
DISP
C
PROG
E
TAPE
• Indoor FM antenna
• Antenne intérieure FM
• UKW-Innenantenne
• FM inomhusantenn
• Antenna FM per interni
• Antena interior de FM
PTY SEEKFREQ PS/PTY/RT/CT
START
• FM binnenantenne
• Batteries (size AAA, UM-4, R03)
• Piles (format AAA, UM-4, R03)
TAPE REC
• Batterien (Größe AAA, UM-4, R03)
• Batterier (Storl. AAA, UM-4, R03)
• Batterie (size AAA, o UM-4, o R03)
• Pilas (tamaño AAA, tipo UM-4, R03)
• Batterijen (maat AAA, UM-4, R03)
<CDX-E100>
• RCA Pin Cable
• Câble de raccordement RCA
• RCA-Stiftkabel
• RCA stiftkabel
• Cavo con spinotti a spillo RCA
• Cable con clavijas RCA
• RCA (tulpstekker) kabel
• System Control Cable
• Câble de commande du système
• Systemsteuerkabel
• Systemkontrollkabel
• Cavo di telecomando del sistema
• Cable de control del sistema
• Systeembedieningskabel
ENGLISH
INTRODUCTION
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the
best performance, read this manual carefully. It will guide you in operating your YAMAHA product.
FEATURES
<RX-E100>
• Minimum RMS Output Power per Channel
40 W + 40 W (6Ω, 20 - 20,000Hz, 0.1% THD)
• Full Operation System Remote Control
• 40-Station FM/AM Preset Tuning
• Multi-Function RDS Reception
• SUBWOOFER Output Terminal
The receiver (RX-E100) and CD player (CDX-E100) are the main units of the YAMAHA E100 series. You could upgrade
the system by adding the cassette deck (KX-E100) and MD recorder (MDX-E100)*.
* MD recorder (MDX-E100) may not be available for some areas.
<CDX-E100>
• S-bit DAC and 8fs Digital Filter
• Optical Digital Output
• Random, Repeat, and Program Play
• CD TEXT Display
• Peak Level Search
• Tape Programming
English
CONTENTS
PRECAUTIONS...................................................2
GETTING STARTED
The remote control ...............................................3
Connecting the speakers .......................................4
Connecting the system..........................................5
<RX-E100>
NAMES OF BUTTONS AND CONTROLS .......6
BASIC OPERATIONS
Listening to a source.............................................8
TUNER OPERATIONS
Listening to the radio............................................ 9
Presetting stations ............................................... 10
RECEIVING RDS STATIONS
Receiving RDS data ...........................................11
PTY SEEK mode................................................ 12
Optional settings for RDS functions...................13
USING THE BUIL T-IN TIMER
Setting the clock ................................................. 14
Adjusting the brightness of the display .............. 14
Before using the timer ........................................ 15
Timer play and recording ...................................15
Sleep timer.......................................................... 16
<CDX-E100>
NAMES OF BUTTONS AND CONTROLS .....17
COMPACT DISC PLAYER OPERATIONS
CD playback .......................................................19
Selecting the time display and CD TEXT ..........20
Random-sequence play.......................................20
Repeat play .........................................................21
Program play ......................................................21
Peak level search ................................................22
ADD KX-E100 AND/OR MDX-E100 TO YOUR
SYSTEM
Operating the cassette deck, KX-E100 and MD
recorder, MDX-E100 with the remote control ... 23
Before recording .................................................24
Dubbing setting ..................................................24
TAPE programming ............................................25
ADDITIONAL INFORMATION
CD preventive care .............................................26
Troubleshooting..................................................26
Specifications .....................................................28
E-1
PRECAUTIONS: READ THIS BEFORE OPERATING THE UNIT
CAUTIONS
• To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
• Install your unit in a well ventilated, cool, dry, clean
place – away from windows, heat sources, vibration,
dust, moisture, or cold. To avoid humming sounds,
locate the unit away from other electrical appliances,
motors, and transformers. To prevent fire or electrical
shock, do not expose to rain and water.
• (U.K. and Europe models only)
Be sure to allow at least 10 cm of ventilation space at
the top, on left, right, and back sides of RX-E100.
• Do not operate the unit upside-down. It may overheat,
possibly causing damage.
• Never open the cabinet. If something drops into the set,
contact your dealer.
• Do not use force on switches, knobs or cords.
• Always set the VOLUME control to minimum before
starting playback of an audio source: increase the
volume gradually to an appropriate level after play has
started.
• When not planning to use this unit for long periods of
time (i.e., vacation, etc.), disconnect the AC power plug
from the wall outlet.
• Grounding or polarization – Precautions should be taken
so that the grounding or polarization of the unit is not
defeated.
• Do not clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
• Be sure to read the “Troubleshooting” section on
common operating errors before concluding that your
unit is faulty.
• Do not place another component on top of this unit, as
damage or discoloration on the surface of the unit may
result.
• To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
• When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
• Do not plug the AC power plug to the wall outlet before
you finish all connections.
• The voltage to be used must be the same as that
specified on this unit. Using this unit with a higher
voltage than that which is specified is dangerous and
may result in a fire or other type of accident causing
damage. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage
other than that which is specified.
• When listening to the receiver at a high volume level for
a long time, the temperature inside the unit rises. To
prevent overheating and possible damage to this unit,
the internal fan starts running.
• Sudden temperature changes and storage or operation in
an extremely humid environment may cause
condensation inside the cabinet.
The unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. This state is called the standby
mode. In this state, this unit is designed to consume a
very small quantity of power.
CAUTION FOR CARRYING THE UNIT
Before carrying the unit, first remove all discs from
the unit, press STANDBY/ON to turn the unit off,
then disconnect the AC power plug from the wall
outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wires in the mains lead are coloured in accordance
with the following code:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The wire which is coloured BLUE
must be connected to the terminal which is marked
with the letter N or coloured BLACK. The wire which
is coloured BROWN must be connected to the terminal
which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described above.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous
if engaged in a live socket outlet.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
This compact disc player is
classified as a CLASS 1
CLASS 1 LASER PRODUCT
LASER product.
The CLASS 1 LASER
PRODUCT label is located
on the rear exterior.
E-2
Laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
GETTING STARTED
The remote control
This remote control controls a whole system: not only
RX-E100 but also CDX-E100. Moreover, a cassette deck
(KX-E100) and MD recorder (MDX-E100) that level up
your system can be operated by it. Operating buttons for
each unit are explained on the pages below:
Receiver, RX-E100: p.7
CD player, CDX-E100: p.18
Cassette deck, KX-E100: p.23
MD recorder, MDX-E100: p.23
Loading the batteries for the remote control
1 Remove the battery compartment cover.
Notes
• Use only AAA, UM-4, R03 batteries for replacement.
• Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
• Remove the batteries if the remote control will not be used for
an extended period of time.
• If batteries leak, dispose of them immediately. Avoid touching
the leaked material or letting it come in contact with clothing,
etc. Clean the battery compartment thoroughly before
installing new batteries.
Remote control operation range
NATURAL SOUND STEREO RECEIVER RX-E100
DISPLAY
STANDBY/ON PHONES
Remote control
sensor
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOUR MIN
BASS TREBLE BALANCE
+-+-
VOLUME
PRESET/TUNINGPRESET/BAND
RL
MAXMIN
INPUT
English
2 Insert 4 batteries into the battery compartment.
3 Replace the battery compartment cover.
Battery replacement
If you find that the remote control must be used closer to
the main unit than usual, the batteries are weak. Replace
batteries with new ones.
Within approximately
6 m (20 feet)
30°
30°
Notes
• There should be no large obstacles between the remote control
and the main unit.
• If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp, etc.),
it might cause the remote control not to work correctly. In this
case, reposition the main unit to avoid direct lighting.
E-3
GETTING STARTED
Connecting the speakers
Never plug the AC power cord to the wall outlet until all connections are completed.
Follow the steps as shown below to connect the system using the supplied cords and accessories.
Right speaker Left speaker
FM antenna
3
75 Ω UNBAL
FREQUENCY
FM ANT GND AM ANT
STEP
AB E
L
TAPE
R
OUT IN IN
L
MD
R
D
C
1 Connect the Speakers.
1 Unscrew the knob.
2 Remove approx. 5 mm (1/4”) of insulation from
each of the speaker wires and insert the bare wire
into the terminal.
3 Tighten the knob to secure the wire.
AM loop antenna
2
6 Ω MIN./SPEAKER
SPEAKERS
1
LR
SYSTEM
SUBWOOFER
CONNETOR
OUT
To wall outlet
4
CD
AUX
3 Connect the FM Antenna.
75 Ω UNBAL
FM ANT
Red: positive(+)
Black: negative(–)
1
2 Connect the AM Antenna.
Set up the AM loop antenna, then connect it.
GND AM ANT
E-4
2
4 Connect the AC power cord to a wall outlet.
• Use external FM/AM antennas if you need better reception.
3
Consult your dealer.
• The AM loop antenna should be placed apart from the main
unit. The antenna may be hung on a wall.
To Connect the Subwoofer (optional)
You can reinforce the bass frequencies by adding a
subwoofer (optional).
Connect the SUBWOOFER OUT terminal of the unit to
the INPUT terminal of the subwoofer.
GETTING STARTED
Connecting the system
Connecting RX-E100 and CDX-E100
1 Connect ‰ to ‰ using the RCA pin cable.
Insert the plugs into the jacks of the same colour.
2 Connect RX-E100 and CDX-E100 with the system control cable.
The other SYSTEM CONNECTOR of CDX-E100 is for connecting MDX-E100 or KX-E100.
3 Connect the AC power plug of CDX-E100 to AC OUTLET of RX-E100.
<CDX-E100>
3
L
R
ANALOG
DIGITAL
OPTICAL
OUT
E
OUT
SYSTEM
CONNECTOR
English
To RX-E100
RCA pin cable
1
FREQUENCY
STEP
L
TAPE
R
OUT IN IN
L
MD
R
75 Ω UNBAL
FM ANT GND AM ANT
AB E
D
C
CD
AUX
6 Ω MIN./SPEAKER
System control cable
LR
SPEAKERS
SUBWOOFER
OUT
SYSTEM
CONNETOR
<RX-E100>
2
To wall outlet
Adding KX-E100 and MDX-E100 to the above system (For details, refer to the owner's manual
supplied with the respective component.)
1 Connect Å and ı of RX-E100 to Å and ı of KX-E100.
2 Connect Ç and Î of RX-E100 to Ç and Î of MDX-E100.
3 Connect an external component to the AUX terminal of RX-E100.
4 Connect DIGITAL OPTICAL OUT of CDX-E100 to DIGITAL OPTICAL IN of MDX-E100.
Take off the covers of the optical fiber cable plug, the DIGITAL OPTICAL OUT jack, and the DIGITAL OPTICAL
IN jack before making digital connections. Be sure to replace the terminal’s cover when the terminal on the rear panel
is not being used, in order to protect from dust.
5 AC OUTLET (CDX-E100)
Connect the AC power plug of MDX-E100 or KX-E100 (Except for the UK model).
E-5
RX-E100 NAMES OF BUTTONS AND CONTROLS
Front panel
NATURAL SOUND STEREO RECEIVER RX-E100
TIMER
STANDBY
DISPLAY
STANDBY/ON PHONES
MEMORY AUTO/MAN'L
TIME ADJ TIMER
PRESET/TUNINGPRESET/BAND
HOUR PTY SELECT MIN
BASS TREBLE BALANCE
VOLUME
MAXMIN
INPUT
~ STANDBY/ON (P.8)
Ÿ PHONES (P.8)
! DISPLAY (P.14)
⁄ MEMORY/TIME ADJ (P.10/P.14)
@ AUTO/MAN’L/TIMER (P.9/P.15)
¤ BASS (P.8)
# TREBLE (P.8)
‹ BALANCE (P.8)
$ INPUT (P.8)
+-+-
› VOLUME (P.8)
% PRESET/TUNING / PTY SELECT
fi PRESET/BAND (P.9)
^ Display (P.6)
fl Remote Control Sensor (P.3)
& TIMER indicator (P.15)
‡ STANDBY indicator (P.8)
Display
RL
(P.9/P.12)
HOUR/MIN (P.14)
PRESET
~ Multi-information display
Ÿ PRESET indicator (P.10)
! STEREO indicator (P.9)
⁄ TUNED indicator (P.9)
@ AUTO indicator (P.9)
¤ MEMORY indicator (P.10)
E-6
STEREO AUTO RDS PS PTY RT CT TIMER
SLEEPTUNED MEMORY PTY HOLD
# RDS indicator (P.11)
‹ RDS mode indicators (P.11)
$ PTY HOLD indicator (P.12)
› TIMER indicator (P.15)
% SLEEP indicator (P.16)
RX-E100 NAMES OF BUTTONS AND CONTROLS
SLEEP DISP
REP
PEAK
TIME
B
RNDM
MODE
VOLUME
TAPE
C
E
PTY SEEKFREQ PS/PTY/RT/CT
A
D
PROG
TAPE
START
Remote control
English
~ SLEEP (P.16)
Ÿ DISP (Display) (P.13)
! A/B/C/D/E (P.10)
⁄ POWER (P.8)
@ Preset numbers (P.10)
¤ FREQ PS/PTY/RT/CT (P.11)
# PTY SEEK MODE (P.12/P.13)
‹ PTY SEEK START (P.12/P.13)
$ VOLUME + – (P.8)
› TAPE (KX-E100) (P.23)
% MD (MDX-E100) (P.23)
fi AUX (The equipment connected to the AUX
terminal) (P.5)
^ CD (CDX-E100) (P.19)
fl TUNER (RX-E100) (P.10)
& PRESET/PTY SELECT / (P.10/P.12)
Note
• ›~fl are operation buttons and input selectors for each
component.
MD CD
AUX
TUNER
PRESET
PTY SELECT
MD REC
MODE START
TAPE REC
TAPE
DUBBING
E-7
RX-E100 BASIC OPERATIONS
Listening to a source
BASS TREBLE BALANCE
+-+-
BASS
SLEEP DISP
TIME
A
REP
B
RNDM
D
PEAK
TREBLE
PRESET/TUNINGPRESET/BAND
HOUR PTY SELECT MIN
C
PROG
E
TAPE
RL
POWER
PHONES
NATURAL SOUND STEREO RECEIVER RX-E100
TIMER
STANTBY
STANDBY/ON PHONES
DISPLAY
MEMORY AUTO/MAN'L
TIME ADJ TIMER
STANDBY/ON INPUTBALANCE
VOLUME
VOLUME
MAXMIN
INPUT
4 Play the source. (Refer to the owner’s manual
supplied with each selected component.)
5 Adjust the volume level by turning VOLUME on the
front panel or pressing VOLUME + on the remote
control.
6 If desired, adjust BASS, TREBLE, and BALANCE.
BASS: Turn this control clockwise to increase (or
counterclockwise to decrease) the low frequency
response.
TREBLE: Turn this control clockwise to increase (or
counterclockwise to decrease) the high frequency
response.
BALANCE: Adjust the balance of the output volume
from the left and right speakers to compensate for
sound imbalance caused by the speaker location or
listening room conditions
• These controls are only effective for the sound from the main
speakers.
PTY SEEKFREQ PS/PTY/RT/CT
MODE
START
VOLUME
TAPE
MD CD
AUX
TUNER
PRESET
PTY SELECT
MD REC
TAPE REC
TAPE
MODE START
DUBBING
VOLUME –/+
1 Set the volume to “MIN” by turning VOLUME.
2 Turn on the power by pressing STANDBY/ON on
the front panel, or POWER on the remote control.
• RX-E100 can be used to turn on or put in standby mode
the system connected E100 series components depending
on their prior standby/on status.
3 Select the desired input source by turning INPUT so
that the source appears on the display.
• When you operate the component connected to the AUX
terminal, turn INPUT to select AUX.
When you use headphones
Connect the headphones to the PHONES jack. You can
listen to the sound from the main speakers through the
headphones.
When you have finished using this
unit
Press STANDBY/ON on the front panel again or
POWER on the remote control to set this unit to the
standby mode.
• The STANDBY indicator lights up.
Auto power off function
RX-E100 will be put automatically into the standby mode
under the following conditions:
• The component connected to RX-E100 is in stop mode
and not operated for 30 minutes.
• TUNER or AUX is not selected as an input source.
E-8
TUNER OPERATIONS
Listening to the radio
You can find radio stations automatically and manually.
AUTO/MAN’L
NATURAL SOUND STEREO RECEIVER RX-E100
DISPLAY
MEMORY AUTO/MAN'L
STANDBY/ON PHONES
TIME ADJ TIMER
PRESET/BAND
Automatic tuning
1 Select TUNER by turning INPUT so that the
frequency of a radio station appears in the display.
2 Press PRESET/BAND to select the reception band.
Do not select the preset tuning mode (in which
“PRESET” appears on the display).
PRESET/TUNING /
PRESET/TUNINGPRESET/BAND
HOUR PTY SELECT MIN
BASS TREBLE BALANCE
+-+-RL
INPUT
VOLUME
INPUT
MAXMIN
Manual tuning
1 Follow steps 1 and 2 described in “Automatic
tuning.”
2 Press AUTO/MAN’L so that “AUTO” disappears
from the display.
3 Press TUNING (For a higher frequency) or
(For a lower frequency) to select your desired station.
• Each time you press TUNING or , the frequency
changes step by step.
English
3 Press AUTO/MAN’L so that “AUTO” appears in the
display.
4 Press PRESET/ TUNING (For a higher
frequency) or
(For a lower frequency).
5 The unit starts searching for a station.
STEREO AUTO
TUNED
When the unit finds a station, the unit stops searching
and “TUNED” appears on the display.
6 If the located station is not the one you want, repeat
steps 4 and 5 until a station you want is tuned.
Notes
• If automatic tuning search does not find the desired station, try
manual tuning as described next.
• When an FM stereo broadcast with sufficient signal strength is
received, “STEREO” appears on the display and you can listen
to stereo sound.
E-9
TUNER OPERATIONS
Presetting stations
The unit can preset station frequencies selected by
Automatic tuning or Manual tuning. Up to 40 stations can
be stored. With this function, you can select any desired
station by pressing the corresponding preset station
number.
PRESET/TUNING /
NATURAL SOUND STEREO RECEIVER RX-E100
MEMORY AUTO/MAN'L
STANDBY/ON PHONES
DISPLAY
TIME ADJ TIMER
PRESET/TUNINGPRESET/BAND
HOUR MIN
PTY SELECT
BASS TREBLE BALANCE
+-+-
To preset stations manually
1 Tune in a desired station.
(Refer to the previous page for the tuning procedure.)
2 Press MEMORY.
3 Within about 5 seconds, use PRESET/TUNING
/ to select a desired preset number. Continue
pressing PRESET/TUNING
group of the preset stations (A, B, C, D, and E).
VOLUME
MAXMIN
INPUT
RL
INPUTPRESET/BANDMEMORY
/ to select the
5 Repeat steps 1 to 4 until all desired stations are
preset.
Notes
• A new setting can be preset in place of a previous one.
• The preset stations are retained for a week after you disconnect
the AC power cord or a power failure occurs.
To preset stations automatically
1 Select TUNER as input source by turning INPUT.
2 Press MEMORY for about 2 seconds.
• The unit starts presetting stations, “AUTO” and
“MEMORY” will flash on the display.
Received stations are stored to A1, A2...A8 sequentially.
After 40 stations or all FM and AM stations are stored, the
display will show the preset station A1.
To recall a preset station
Press TUNER and select the desired number by pressing
PRESET/BAND and PRESET/TUNING / on the
front panel or PRESET
the remote control.
/ , A/B/C/D/E and 1-8 on
SLEEP DISP
TIME
A
D
C
REP
PEAK
PROG
B
RNDM
E
TAPE
A/B/C/D/E
STEREO
PRESET
TUNED
MEMORY
4 Press MEMORY.
•“MEMORY”, “PRESET”, and preset number will appear
on the display.
The arrow will appear for a second when
it is preset.
STEREO
PRESET
TUNED
MEMORY
E-10
TUNER
PRESET
PTY SEEKFREQ PS/PTY/RT/CT
MODE
VOLUME
TAPE
MD CD
AUX
TUNER
PRESET
PTY SELECT
MD REC
TAPE REC
TAPE
MODE START
DUBBING
1~8
START
RECEIVING RDS STATIONS
Receiving RDS data
RDS (Radio Data System) is a data transmission system
which has been introduced by FM stations in many
European countries. Stations using this system transmit an
inaudible stream of data in addition to the normal radio
signal. RDS data contains various types of information,
such as PS (Program Service), PTY (Program Type), RT
(Radio Text), and CT (Clock Time).
SLEEP DISP
TIME
A
D
FREQ PS/
PTY/RT/CT
TUNER
MD REC
REP
B
RNDM
PEAK
PTY SEEKFREQ PS/PTY/RT/CT
MODE
VOLUME
TAPE
MD CD
AUX
TUNER
PRESET
PTY SELECT
TAPE REC
TAPE
C
PROG
E
TAPE
START
PS
The name of the RDS station being received is displayed.
• If the unit cannot find a station with PS data, the unit stops
searching and “NO PS” appears on the display.
RDS PS PTY RT CT
PTY
The type of the program on the RDS station now being
received is displayed. You can make this unit search for a
station which is broadcasting a program of a desired
Playing CDsGetting Started
program type. (Refer to PTY program mode in the next
section for details.)
RDS PS PTY RT CT
RT
Information about the program (such as the title of the
track, artist name, etc.) on the RDS station being received
is displayed using a maximum of 64 alphabetical
characters, including umlaut sign. If other characters are
used in the RT data, they are displayed with an under-bar.
• If the unit cannot find a station with RT data, the unit stops
searching and “NO RT” appears on the display.
RDS PS PTY RT CT
English
MODE START
DUBBING
1 Tune in the FM station. (Refer to page 9, or you can
simply press TUNER on the remote control.)
2 Press FREQ PS/PTY/RT/CT to choose the mode.
Each time you press FREQ PS/PTY/RT/CT, the
type changes as follows:
CT
Current time is displayed.
• If the unit cannot find a station with CT data, the unit stops
searching and “NO CT” appears on the display.
RDS PS PTY RT CT
Note
• RDS may not work properly if the station you are tuned to is
not transmitting the RDS signal properly or if the signal
strength is weak.
• Some FM stations do not offer RDS service. Of those that do,
not all provide the same types of services. The types provided
by the received RDS station are dimmed on the display. Check
with your local radio stations for details on RDS services in
your area.
E-11
RECEIVING RDS STATIONS
PTY SEEK mode
To locate a station
You can locate a desired station by selecting a program
type. The unit searches all preset stations into the type of
programs currently being broadcast from the RDS
stations.
SLEEP DISP
TIME
A
D
MD REC
C
B
RNDM
MODE
VOLUME
TAPE
AUX
TUNER
PRESET
PTY SELECT
TAPE
DUBBING
PTY SEEKFREQ PS/PTY/RT/CT
PROG
E
TAPE
START
TAPE REC
REP
PEAK
MD CD
MODE START
PTY SEEK MODE
PTY SEEK START
PTY SELECT /
1 Tune in the FM station. (Refer to page 9, or you can
simply press TUNER on the remote control.)
2 Press PTY SEEK MODE once so that “PTY” and a
PTY program flashes on the display.
PTY
3 Within about 20 seconds, press PTY SELECT
(for a higher frequency) or (for a lower
frequency) until the desired program type appears on
the display.
4 Within about 20 seconds, press PTY SEEK START.
• If a station broadcasting the selected program type is
found, the unit stops searching and the Program Service
name appears on the display.
“PTY HOLD” appears on the display.
PRESET
RDS PTY
PTY HOLD
List of PTY (Program Type)
NEWS
News
AFFAIRS
Current Affairs
INFO
General Information
SPORT
Sports
EDUCATE
Education
DRAMA
Drama
CULTURE
Culture
SCIENCE
Science
VARIED
Light Entertainment
POP M
Pops
ROCK M
Rock
M.O.R. M
Middle of the Road
Music (Easy-listening)
LIGHT M
Light Classics
CLASSICS
Serious Classics
OTHER M
Other Music
E-12
5 Repeat step 4 until the desired station is located.
If there is no station broadcasting the program type
you select, “NO PTY” appears on the display, then
the Program Service name or frequency appears on
the display.
RECEIVING RDS STATIONS
Optional settings for
RDS functions
The tuner has the following functions which make use of
the RDS data service. These are originally in operation
ON. However, you can turn these functions OFF, if so
desired.
DISP
PTY SEEK MODE
PTY SEEK START
FREQ PS/
PTY/RT/CT
TUNER
SLEEP DISP
TIME
A
REP
B
RNDM
D
PEAK
PTY SEEKFREQ PS/PTY/RT/CT
MODE
VOLUME
TAPE
MD CD
AUX
TUNER
PRESET
PTY SELECT
MD REC
TAPE
MODE START
DUBBING
C
PROG
E
TAPE
START
TAPE REC
• If you receive an RDS station of some other country, the
built-in clock is synchronized with the time setting of the
country.
• If the built-in clock is not yet set for the current time or
reset due to a power failure, etc., it will be set for the time
defs
of the CT data automatically, whether this setting is ON
or OFF.
2. LOCAL = CT (ON/OFF)
If the RDS station being received employs the
local time (summer time, etc.) data service, its time
is displayed in the CT mode.
Playing CDsGetting Started
3. A.M. = RDS (ON/OFF)
RDS stations are searched instead of all FM
stations by the automatic preset tuning operation
when the setting is ON. (Refer to page 10.)
4. RT SPEED: ±0
Changes the scrolling speed of the radio text
decreasing the value and, in turn, reducing the
speed.
English
1 Select the FM band by pressing TUNER.
2 Press DISP to display the current time.
3 Press FREQ PS/PTY/RT/CT.
4 Each time you press PTY SEEK MODE the display
will change as follows:
1. CT = CLOCK (ON/OFF)
The tuner corrects the time of the built-in clock
automatically by synchronizing it with the CT data
on the RDS station being received.
Control Range: ±0 to ±3 (Preset value: ±0)
5 Choose the function ON or OFF by pressing PTY
SEEK START, confirming it in the display.
Press PTY SEEK START repeatedly to change the
value for RT SPEED.
• If there is no operation for about 20 seconds, this mode is
cancelled and turns into the frequency display. If the
station has PS data, it turns into the PS mode.
6 Press FREQ PS/PTY/RT/CT again to restore the
frequency display mode.
E-13
USING THE BUILT-IN TIMER
Setting the clock
You must set the clock before you use the timer functions.
The clock is based on a 24-hour system.
HOURDISPLAY
NATURAL SOUND STEREO RECEIVER RX-E100
DISPLAY
MEMORY AUTO/MAN'L
STANDBY/ON PHONES
TIME ADJ TIMER
BASS TREBLE BALANCE
PRESET/BANDTIME ADJ
1 While the power is on, press DISPLAY to display
the time.
2 While holding TIME ADJ, press HOUR to set the
hour.
• If you want to move the time in the reverse direction,
press HOUR while holding TIME ADJ and PRESET/
BAND.
3 While holding TIME ADJ, press MIN to set the
minutes.
• If you want to move the time in the reverse direction,
press MIN while holding TIME ADJ and PRESET/
BAND.
MIN
PRESET/TUNINGPRESET/BAND
HOUR PTY SELECT MIN
+-+-
RL
VOLUME
INPUT
MAXMIN
Adjusting the brightness
of the display
You can adjust the brightness of the display. If you have
connected the CD player (CDX-E100), cassette deck
(KX-E100), and/or MD recorder (MDX-E100) to this
unit, the brightness of the displays is automatically
adjusted to that of this unit.
DISPLAY
NATURAL SOUND STEREO RECEIVER RX-E100
MEMORY AUTO/MAN'L
STANDBY/ON PHONES
DISPLAY
TIME ADJ TIMER
PRESET/TUNINGPRESET/BAND
HOUR PTY SELECT MIN
BASS TREBLE BALANCE
+-+-
Press and hold DISPLAY for about two seconds so that
“Dimmer ±0” appears on the display. While holding
DISPLAY, turn INPUT clockwise to increase or
counterclockwise to decrease brightness.
RL
INPUT
VOLUME
INPUT
MAXMIN
To display the clock
Press DISPLAY.
The current time appears for about 8 seconds, then the
normal display returns.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
E-14
Control Range: ±0 to –6 (Preset value: ±0)
USING THE BUILT-IN TIMER
Before using the timer
If you want to use the cassette deck, KX-E100 or the MD
Recorder, MDX-E100 for timer play or recording, you
must first make the connections as shown in “Connecting
the system” on page 5. For details, refer to the instructions
supplied with the MDX-E100 or KX-E100.
Timer play and recording
By using the built-in timer, you can have the unit turn on
at a specified time and begin playing or recording
automatically. You can also specify the turn off time.
DISPLAY
NATURAL SOUND STEREO RECEIVER RX-E100
DISPLAY
STANDBY/ON PHONES
MEMORY AUTO/MAN'L
TIME ADJ TIMER
BASS TREBLE BALANCE
MIN
PRESET/TUNINGPRESET/BAND
HOUR PTY SELECT MIN
+-+-RL
HOURTIMER
VOLUME
INPUT
INPUT
MAXMIN
3. Timer REC
Select the recording component by turning INPUT.
If you like to enjoy timer play with TUNER or
AUX, select “REC Mode OFF”.
(Example)
4. ON Time
“ON Time” appears on the display for a second,
and changed to the time setting mode.
Press HOUR to set the hour.
Press MIN to set the minute.
5. OFF Time
Set the time the same way as above.
If you set the ON time but not OFF time, the timer
play or recording will finish automatically after an
hour.
Notes
• The display mode will change in about 8 seconds. If the
mode is changed before the setting is completed, call the
mode again by pressing DISPLAY once or more.
• If you select the input other than TUNER and AUX on
“2. Timer Input”, “3. Timer REC” is skipped.
English
1 Press DISPLAY.
Whenever DISPLAY is pressed, the display mode
changes as follows:
1. Clock Time (TIMER on/off mode)
If you have not set the clock yet “Set Clock”
appears. You need to set the current time as
described on page 14.
2. Timer Input
Select the source to be played by turning INPUT.
• Timer recording is possible only when you select
TUNER or AUX.
2 Press TIMER to complete the timer setting.
The system is put in the standby mode.
• The STANDBY and TIMER indicators light up.
If you continue using the system, press STANDBY/
ON to turn on this unit.
To cancel the timer play setting
Press DISPLAY to show the current time, then press
TIMER so that “TIMER” goes off from the display. You
can also cancel by pressing TIMER in standby mode.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
E-15
USING THE BUILT-IN TIMER
Sleep timer
The unit can be turned off automatically at a selected
SLEEP time.
A
D
SLEEP
REP
PEAK
B
SLEEP
1 Play the desired sound source.
2 Press SLEEP repeatedly until the desired sleep time
appears in the display.
Each time you press SLEEP, the sleep time changes
as follows:
TIME
RNDM
DISP
C
PROG
E
TAPE
3 The unit will turn off automatically when the selected
sleep time is reached.
SLEEP 2h00m
SLEEP 1h30m
SLEEP 1h00m
SLEEP 0h30m
SLEEP OFF
About 4 seconds after setting, the normal display will
resume.
• “SLEEP” will appear in the display.
E-16
CDX-E100 NAMES OF BUTTONS AND CONTROLS
NATURAL SOUND COMPACT DISC PLAYER CDX-E100
STANDBY/ON
~ STANDBY/ON (P.19)
Ÿ Display (this page)
! $/! (Skip/Search Backward)
⁄/› (Skip/Search Forward) (P.19)
Front panel
English
⁄ ^ (Play/Pause) (P.19)
@ & (Stop) (P.19)
¤ (Open/Close) (P.19)
# Disc Tray (P.19)
REPEAT
SF
TITLE ARTIST TRACK CD-TEXT
~ Multi-information Display
Ÿ * Pause indicator
! # Play indicator
⁄ A B Tape side indicator (P.25)
@ Music calendar
PROGRAM
Display
123456789
11 12 13 14 15 16 17 18 19 20
¤ RANDOM indicator (P.20)
# PROGRAM indicator (P.21)
‹ REPEAT S/F (Single or Full) indicator (P.21)
$ CD-TEXT indicator (P.20)
ABRANDOM
10
E-17
CDX-E100 NAMES OF BUTTONS AND CONTROLS
Remote control
~ TIME (P.20)
Ÿ REP (Repeat) (P.21)
SLEEP
A
D
REP
PEAK
TIME
B
RNDM
MODE
VOLUME
DISP
C
PROG
E
TAPE
PTY SEEKFREQ PS/PTY/RT/CT
START
! PROG (Program) (P.21)
⁄ RNDM (Random) (P.20)
@ PEAK (Peak Search) (P.22)
¤ TAPE (P.25)
# POWER (P.19)
‹ Numeric buttons (P.19)
$ CD input (P.19)
› $/! (Skip/Seach Backward) (P.19)
% ›/⁄ (Skip/Seach Forward) (P.19)
fi ^ (Play/Pause) (P.19)
^ & (Stop) (P.19)
TAPE
MD CD
AUX
TUNER
PRESET
PTY SELECT
MD REC
MODE START
TAPE REC
TAPE
DUBBING
E-18
COMPACT DISC PLAYER OPERATIONS
CD playback
NATURAL SOUND COMPACT DISC PLAYER CDX-E100
STANDBY/ON
STANDBY/ON
$/!/›/⁄
To play CDs
SLEEP
TIME
A
REP
B
RNDM
D
PEAK
PTY SEEKFREQ PS/PTY/RT/CT
MODE
VOLUME
TAPE
MD CD
AUX
TUNER
PRESET
PTY SELECT
MD REC
TAPE
MODE START
DUBBING
DISP
C
PROG
E
TAPE
START
TAPE REC
POWER
Numeric
buttons
CD
^
&
3 Press to open the disc tray, and place a CD on the
English
tray.
^&
0
0
1
-E
X
D
C
R
E
Y
A
L
P
C
IS
D
T
C
A
P
M
O
C
D
N
U
O
S
L
A
R
U
T
A
N
STANDBY/ON
4 Press ^ to start playback.
The unit starts playback of the CD.
To pause playback
⁄/›$/!
Press ^.
To resume play, press ^ again.
To stop playback
Press &.
To eject the CD
Press to open the disc tray, and remove the CD from
the tray.
To play a specific track on the disc
(Skip)
Direct play
Select a desired track using the numeric button.
(Example: To select 35, press +10 three times so that
“3 –” appears in the display, then press 5.)
Skip play
Press › to skip forward or $ to skip backward. Press
once for each track to be skipped.
Notes
• You cannot enter a number that is higher than the last track
number on the disc.
• These operations can also be performed when the unit is in the
pause or stop mode.
• During stop mode, if › or $ is pressed, the track number
successively changes to higher numbers (or lower numbers).
1 Press STANDBY/ON to turn on this unit and also
RX-E100.
2 Press CD on the remote control in order to operate
the CD player by the remote control.
To advance or reverse playback
rapidly (Search)
Press and hold ⁄ to advance playback rapidly, and !
to reverse playback rapidly.
E-19
COMPACT DISC PLAYER OPERATIONS
Selecting the time
display and CD TEXT
You can select any of four time displays by pressing
TIME. When you play a CD with CD TEXT, the disc
title, artist name, and track name are also displayed.
SLEEP
A
REP
B
D
PEAK
Each time you press TIME, the display changes as
follows:
• “CD-TEXT” appears on the display if a
CD has CD TEXT.
DISP
TIME
C
PROG
RNDM
E
TAPE
Elapsed time of the
current track
Remaining time of the
current track
Total disc play time
Total remaining time of
the disc
TIME
Random-sequence play
The unit can play all the tracks in a random sequence.
TIME
B
RNDM
C
PROG
E
DISP
RNDM
TAPE
SLEEP
A
REP
D
PEAK
Press RNDM.
• “RANDOM” appears on the display.
The unit starts random sequence play.
To cancel random-sequence play
mode
Press & or RNDM.
• “RANDOM” disappears from the display.
Notes
• This feature will not function during programming, or during
programmed play.
• If › is pressed during random-sequence play, the next
randomly programmed track will be played.
If $ is pressed, play will return to the beginning of the
current track.
• Total remaining time on the disc will not be displayed during
random-sequence play.
Disc title
Artist name
Track name
Note
• The disc title, artist names, or track names may not be
displayed with some CD TEXT discs. In this case, “(NO
ENTRY)” appears on the display.
E-20
COMPACT DISC PLAYER OPERATIONS
Repeat play
You can play any desired track or disc repeatedly.
Press REP to select the repeat mode.
SLEEP
A
REP
REP
B
D
PEAK
SINGLE REPEAT
The current track is played repeatedly.
REPEAT S
TIME
RNDM
DISP
C
PROG
E
TAPE
Program play
By creating a program, you can enjoy listening to your
favourite tracks in any desired order. As many as 30
tracks can be programmed in sequence.
SLEEP
A
REP
D
PEAK
MD CD
MD REC
TIME
B
RNDM
MODE
VOLUME
TAPE
AUX
TUNER
PRESET
PTY SELECT
TAPE
DISP
C
PROG
E
TAPE
PROG
Numeric
buttons
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE REC
› / $
English
FULL REPEAT
The current disc is played repeatedly.
• In random-sequence play mode, all randomly sequenced tracks
are played repeatedly in the same order.
REPEAT F
To cancel repeat play mode
Press REP successively until “REPEAT F” disappears
from the display.
^
MODE START
DUBBING
&
1 Press & to stop the unit.
2 Press PROG.
• “PROGRAM” appears in the display.
PROGRAM
3 Use the numeric buttons to select a track number
until the desired track number appears on the display.
PROGRAM
4 Repeat step 3 to program more tracks. You can select
the same track again.
5 Press ^ to start program play.
E-21
COMPACT DISC PLAYER OPERATIONS
To stop program play mode
Press &.
Note
• › or $ can be used during program play to skip to tracks
within the program.
To check program data
1. Press & to stop program play.
2. Press PROG. Then each time you press › /
$,
the track number and the program number are
displayed in the order of the program.
To change program data
1. Follow the preceding procedure described in “To
check program data.”
2. Display the track number to be changed by pressing
› /
$.
3. Press the numeric button of the desired track. The
previously programmed track will be cleared from
memory and the new one will be programmed.
Peak level search
This unit can find the peak sound level on the CD for
optimum adjustment of the recording volume level.
TIME
RNDM
DISP
C
PROG
E
TAPE
SLEEP
A
REP
B
D
PEAK
PEAK
Press PEAK while the player is stopped or the tray is
opened.
• It takes a few minutes to search for the peak level. When
found, the unit plays the peak level for 4 seconds repeatedly.
To cancel searching
To delete all program data
When program play is stopped, press &.
Press &.
E-22
ADD KX-E100 AND/OR MDX-E100 TO YOUR SYSTEM
Operating the cassette deck, KX-E100 and MD
recorder, MDX-E100 with the remote control
MDX-E100
SLEEP
A
D
MD REC
TIME
REP
B
RNDM
PEAK
PTY SEEKFREQ PS/PTY/RT/CT
MODE
VOLUME
TAPE
MD CD
AUX
TUNER
PRESET
PTY SELECT
TAPE
DISP
C
PROG
E
TAPE
,
START
*
TAPE REC
~ TIME (Same function as DISPLAY on
MDX-E100 remote control)
Ÿ REP (Repeat)
! PROG (Program)
⁄ RNDM (Random)
@ POWER
¤ Numeric buttons
# MD input
‹ MD REC/PAUSE
$ $/! (Skip/Search Backward)
› ›/⁄ (Skip/Search Forward)
% & (Stop)
fi ^ (Play/Pause)
KX-E100
1 POWER
2 TAPE input
3 TAPE REC/PAUSE
4 @# (Tape Direction)
5 $/! (Rewind/Music Search Backward)
6 ›/⁄ (Fast Forward/Music Search Fast
Forward)
7 & (Stop)
8 ^ (Play)**
English
* Input selectors when recording.
,
,
**There is no pause function on KX-E100.
,,
MODE START
DUBBING
E-23
ADD KX-E100 AND/OR MDX-E100 TO YOUR SYSTEM
Before recording
When you record by using MDX-E100 or KX-E100, you
must first make the connections as shown in “Connecting
the system” on page 5. For details, refer to the instructions
supplied with the MDX-E100 or KX-E100. A source from
the component which is connected to the AUX terminal
component can be recorded on a tape or MD.
Dubbing setting
There are six different combinations of components. Once
you choose a certain mode, recording starts and ends
automatically in a certain way for each mode.
MD REC
TAPE REC
TAPE
2
• Only the first track is recorded. After recording the
CD tray opens automatically.
3
4
• Same as CD (Tr1) = TAPE
5
Play unit
Record unit
DUBBING
MODE
MODE START
DUBBING
DUBBING
START
1 Decide the combination of the components. Each
time you press DUBBING MODE, the mode will
change in the below order.
1
• Recording automatically starts from the beginning
of the tape. (By pressing DUBBING START, the
tape automatically rewinds to the beginning if it is
in the middle.)
• When the recording on side A finishes while a
track is being played back, the recording on side B
starts from the beginning of the same track.
• The sound is automatically faded out when it gets
close to the end of side B.
• Same as CD = TAPE
6
• Recording automatically starts at the beginning of
the tape. (By pressing DUBBING START, the
tape automatically rewinds to the beginning if it is
in the middle.)
Play unit
Record unit
2 Press DUBBING START to start recording.
Note
• The displays 1~6 which include the component you have not
connected to your receiver (RX-E100) will be skipped.
E-24
ADD KX-E100 AND/OR MDX-E100 TO YOUR SYSTEM
TAPE Programming
By specifying the length of the tape, the CD player,
CDX-E100 programs tracks or helps you to program
tracks so they will fit onto the tape with the least amount
of unrecorded space remaining at each end of the tape.
There are three ways of programming.
1 Manual TAPE programming
REP
RNDM
SLEEP
A
REP
D
PEAK
MD CD
MD REC
TIME
B
RNDM
MODE
VOLUME
TAPE
AUX
TUNER
PRESET
PTY SELECT
TAPE
DISP
C
PROG
E
TAPE
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE REC
PROG
TAPE
3 Press PROG to start programming.
• “A B” appears in the display to indicate the direction
of the tape.
4 Select the desired track number using numeric
buttons.
• Repeat step 4 to continue programming tracks.
• The remaining time is shown on the display. If the track is
longer than the remaining time, “Error” appears on the
display.
5 Press TAPE to continue programming tracks on side
B.
• Repeat step 4.
6 Press PROG to confirm the program.
7 Choose CD = TAPE by pressing DUBBING
MODE, and press DUBBING START to start
recording.
2 Automatic TAPE programming
1 Repeat steps 1 and 2 of “Manual TAPE
programming”.
2 Press REP to start programming.
• Programming is done in the order on the CD from side A
to side B. When complete, the programmed track number
and total time are indicated in the display for 3 seconds.
English
DUBBING
MODE
MODE START
DUBBING
DUBBING
START
1 Insert the desired disc into the CD player, and load a
blank tape into the KX-E100.
2 Press TAPE repeatedly to select the length of tape to
be used. Each time you press TAPE, the length of the
tape changes as follows:
46 54
90 60
• You can use numeric buttons to input the length of the
tape.
3 Press PROG to confirm the program.
4 Choose CD = TAPE by pressing DUBBING
MODE, and press DUBBING START to start
recording.
3 Random TAPE programming
1 Repeat steps 1 and 2 of “Manual TAPE
programming”.
2 Press RNDM to start programming.
• Programming of CD tracks is done randomly from side A
to side B. When complete, the programmed track number
and total time are indicated in the display for 3 seconds.
3 Press PROG to confirm the program.
4 Choose CD = TAPE by pressing DUBBING
MODE, and press DUBBING START to start
recording.
E-25
ADDITIONAL INFORMATION
CD preventive care
• This compact disc player is designed for playing
compact discs bearing the
attempt to load any other type of disc into the unit.
The unit will also play 8-cm (3-inch) compact discs.
• Compact discs are not subjected to wear during play,
but damage to the disc surface when the disc is being
handled can adversely affect the disc’s play.
• Do not use cleaning discs or warped discs. All of these
could damage the unit.
or mark only. Never
To prevent a malfunction of this unit
• Do not use any non standard shaped CD (heart, etc.)
available on the market, because it may damage the
unit.
• Do not use a CD with tape, seals, or paste on it, because
damage to the unit may result.
• Compact discs are not affected by small particles of
dust or fingerprints on their playing surface, but even so
they should be kept clean. Wipe by using a clean, dry
cloth. Do not wipe with a circular motion; wipe straight
outward from the center.
• Do not try to clean the disc’s surface by using any type
of disc cleaner, record spray, antistatic spray or liquid,
or any other chemical-based liquid, because such
substances might irreparably damage the disc’s surface.
• Do not expose discs to direct sunlight, high temperature
or high humidity for a long period of time, because
these might warp or otherwise damage the disc.
No!
Troubleshooting
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the
simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the
power cord and contact your authorized YAMAHA dealer or service center for help. When taking the service, the
MDX-E100 or KX-E100 may be needed. For details, contact your authorized YAMAHA dealer or service center.
SYMPTOM CAUSE REMEDY
The unit does not switch ON when
the STANDBY/ON switch is pressed.
No sound from one speaker.
No sound from speakers.
No sound from an external unit
connected with this unit or play does
not begin.
RX-E100 RECEIVER
E-26
The AC power cord is not connected or not
completely connected.
Loose speaker connections.
Internal protection circuit is functioning.
Incorrect cord connections.
Input source selection is not proper.
Securely connect the power cord.
Connect properly.
Unplug the AC power cord from the wall outlet, and
then plug in again.
Connect the cords properly. If the problem persists,
the cords may be defective.
Make a proper input source selection.
ADDITIONAL INFORMATION
SYMPTOM CAUSE REMEDY
Excessive static in FM broadcasts.
Noise increases during stereo
broadcasts.
Stereo broadcasts are noisy and
STEREO indicator blinks on and off.
Cannot select preset stations.
Buzzing or static during AM
broadcasts.
RX-E100 RECEIVER
AM broadcast sensitivity is poor.
Cannot set timer.
The unit does not work normally.
Play does not begin.
Play is delayed, or begins at the
wrong place.
CD synchronized recording or
Automatic recording function does
not work.
Sound “skips.”
CDX-E100 CD PLAYER
Sound “hums.”
Noise from inside of the unit.
The remote control does not work.
TV functions strangely when the
REMOTE CONTROL
remote control is being used.
Interference from starting motor of a nearby
car.
Interference from the thermostat of a nearby
electrical appliance.
Antenna input is too weak due to obstructions
or excessive distance from the broadcasting
station.
Insufficient antenna input.
Preset memory has been erased.
Interference from sources such as lightning,
fluorescent lights, electric motors or
thermostat of nearby electrical appliance.
TV or microprocessor is being used nearby.
Radio signal is weak or the antenna is not
properly connected.
Current time is not set.
The internal microcomputer has been frozen
by an external electric shock (lightning,
excessive static electricity, etc.) or the power
supply with low voltage.
The disc is damaged.
There is moisture on the laser pick-up.
The disc has been loaded upside down.
The disc is dirty.
The disc may be scratched or damaged.
The system cable is not connected securely.
The unit is being subjected to vibrations or
impacts.
The disc is dirty.
Improper cable connections.
The disc may be warped.
The batteries of the remote control are too
weak.
Remote control is too far away or is being
used at an incorrect angle.
Direct sunlight or lighting (of an inverter type
of fluorescent lamp, etc.) is striking the
remote control sensor of the unit.
Remote control is being used near TV set
with a remote control sensor.
Position the FM antenna as high and as far away
from nearby roads as possible. Connect using a
coaxial cable.
Check the antenna connection.
Install a multi-element type FM antenna if possible.
Install an antenna appropriate for the electric field
strength of your area.
Reprogram memory presets.
The problem is difficult to eliminate, but can be
lessened by grounding AM loop antenna.
Move away from TV or microprocessor.
Properly connect the AM loop antenna.
Change orientation of the AM loop antenna.
Install an external AM loop antenna.
Set current time.
Unplug the AC power cord from the wall outlet, and
then plug in again after about one minute.
Check the disc carefully; replace it if necessary.
Wait 20 to 30 minutes after switching the unit ON
before trying to play a disc.
Reload the disc with the label side facing up.
Clean the disc.
Check the disc carefully; replace it if necessary.
Connect the system cable properly.
Relocate the unit.
Clean the disc.
Securely connect the audio cables. If the problem
persists, the cables may be defective.
Replace the disc.
Replace the batteries with new ones.
Use within 6 meters and 60 degree radius.
Change the position of the unit.
Relocate this unit away from the TV or cover the
TV’s remote control sensor.
English
E-27
ADDITIONAL INFORMATION
Specifications
<RX-E100>
Amplifier section
Minimum RMS output power per channel
.............................................. 50 W + 50 W (6Ω 1kHz 0.07% THD)
.................................. 40 W + 40 W (6Ω 20 - 20,000Hz 0.1% THD)
DIN Standard output power per channel (Europe model)
................................................ 60 W + 60 W (4Ω 1kHz 0.7% THD)
Input sensitivity/Impedance
CD/TAPE/MD/AUX
............................................................................ 150 mV/47 k-ohms
Tuner section
Tuning range
FM
[U.S.A. and Canada models]
..............................................................................87.5 – 107.9 MHz
[U.K., Europe, Australia, and General models]
..........................................................................87.50 – 108.00 MHz
AM
[U.S.A. and Canada models]
................................................................................. 530 – 1710 kHz
[U.K., Europe, and Australia models]
................................................................................. 531 – 1611 kHz
[General model]
................................................................. 530/531 – 1710/1611 kHz
Sensitivity
FM (S/N 30dB)
................................................................................................1.5 µV
FM (S/N 26dB) (DIN)
................................................................................................1.8 µV
AM
.......................................................................................... 300 µV/m
General
Power supply
[U.S.A. and Canada models]
............................................................................... AC 120 V, 60 Hz
[Australia model]
............................................................................... AC 240 V, 50 Hz
[U.K. and Europe models]
............................................................................... AC 230 V, 50 Hz
[General model]
.................................................... AC 110/120/220/240 V, 50/60 Hz
Power consumption
[U.S.A. and Canada models]
................................................................................................ 110 W
[U.K., Europe, Australia, and General models]
................................................................................................ 100 W
Dimensions (W x H x D)
..........................................................................217 x 108 x 312 mm
Weight
................................................................................................. 4.5 kg
Accessories
.................................................................................. Remote control
Batteries
Indoor FM antenna
AM loop antenna
<CDX-E100>
CD player section
D/A converter
..........................................................................................S-bit DAC
Frequency response (2 – 20,000 Hz)
............................................................................................. ±0.5 dB
S/N ratio
............................................................................................... 102 dB
Laser Diode Properties
• Material: GaAIAs
• Wavelength: 780 nm
• Emission duration: continuous
• Laser output: max. 44.6 µW*
* This output is the value measured at a distance of about 200 mm
from the objective lens surface on the Optical Pick-up Block.
General
Power supply
[U.S.A. and Canada models]
............................................................................... AC 120 V, 60 Hz
[Australia model]
............................................................................... AC 240 V, 50 Hz
[U.K. and Europe models]
............................................................................... AC 230 V, 50 Hz
[General model]
.................................................... AC 110/120/220/240 V, 50/60 Hz
Power consumption
.................................................................................................. 13 W
Dimensions (W x H x D)
..........................................................................217 x 108 x 290 mm
Weight
................................................................................................. 3.0 kg
Accessories
................................................................................... RCA pin cable
System control cable
Specifications are subject to change without notice.
E-28
AANVULLENDE INFORMATIE
Technische gegevens
<RX-E100>
Versterkergedeelte
Minimaal RMS uitgangsvermogen per kanaal
........................................ 50 W + 50 W (6 Ohm 1kHz 0,07% THD)
............................ 40 W + 40 W (6 Ohm 20 - 20.000Hz 0,1% THD)
DIN standaard uitgangsvermogen per kanaal (Modellen voor Europa)
.......................................... 60 W + 60 W (4 Ohm 1kHz 0,7% THD)
Ingangsgevoeligheid/Impedantie
CD/TAPE/MD/AUX
..........................................................................150 mV/47 kiloOhm
Tunergedeelte
Afstembereik
FM
[Modellen voor U.S.A. en Canada]
..............................................................................87,5 – 107,9 MHz
[Modellen voor Groot-Brittannië, Europa, Australië en algemene
modellen]
..........................................................................87,50 – 108,00 MHz
AM
[Modellen voor U.S.A. en Canada]
................................................................................. 530 – 1710 kHz
[Modellen voor Groot-Brittannië, Europa en Australië]
................................................................................. 531 – 1611 kHz
[Algemene modellen]
................................................................. 530/531 – 1710/1611 kHz
Gevoeligheid
FM (S/R 30 dB)
.................................................................................... 1,5 microWatt
FM (S/R 26 dB) (DIN)
.................................................................................... 1,8 microWatt
AM
...............................................................................300 microWatt/m
Algemeen
Stroomvoorziening
[Modellen voor U.S.A. en Canada]
...............................................120 VIEWCAM wisselstroom, 60 Hz
[Modellen voor Australië]
...............................................240 VIEWCAM wisselstroom, 50 Hz
[Modellen voor Groot-Brittannië en Europa]
...............................................230 VIEWCAM wisselstroom, 50 Hz
[Algemene modellen]
.................... 110/120/220/240 VIEWCAM wisselstroom, 50/60 Hz
Stroomverbruik
[Modellen voor U.S.A. en Canada]
................................................................................................ 110 W
[Modellen voor Groot-Brittannië, Europa, Australië en algemene
modellen]
................................................................................................ 100 W
Afmetingen (B x H x D)
..........................................................................217 x 108 x 312 mm
Gewicht
................................................................................................. 4,5 kg
Accessoires
.............................................................................. Afstandbediening
Batterijen
FM binnenantenne
AM ringantenne
<CDX-E100>
CD-speler gedeelte
D/A converter
..........................................................................................S-bit DAC
Frequentierespons (2 - 20.000 Hz)
............................................................................................. ±0,5 dB
S/R verhouding
............................................................................................... 102 dB
Eingenschappen laserdiode
• Materiaal: GaAIAs
• Golflengte: 780 nm
• Emissieduur: continu
• Laser uitgangsvermogen: max. 44,6 microWatt*
* Dit uitgangsvermogen is de waarde op ongeveer 200 mm afstand
van het oppervlak van de lens op het Optische pick-up blok.
Algemeen
Stroomvoorziening
[Modellen voor U.S.A. en Canada]
...............................................120 VIEWCAM wisselstroom, 60 Hz
[Modellen voor Australië]
...............................................240 VIEWCAM wisselstroom, 50 Hz
[Modellen voor Groot-Brittannië en Europa]
...............................................230 VIEWCAM wisselstroom, 50 Hz
[Algemene modellen]
.................... 110/120/220/240 VIEWCAM wisselstroom, 50/60 Hz
Stroomverbruik
.................................................................................................. 13 W
Afmetingen (B x H x D)
..........................................................................217 x 108 x 290 mm
Gewicht
................................................................................................. 3,0 kg
Accessoires
....................................................................RCA (tulpstekker) kabel
Systeembedieningskabel
Technische gegevens kunnen zonder voorafgaande berichtgeving
gewijzigd worden.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia V423480
Loading...