This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that
may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/
s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful
to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur
in all installations. If this product is found to be the source of interference, which can be determined by turning the product “OFF”
and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the leadin to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please contact Yamaha Systems Technology, Inc. 100 Century Center
Court, San Jose, CA95112, U.S.A.
• This manual applies to the CDR200t and CDR200t-NB.
The CDR200t front panel displays the YAMAHA brand name.
The CDR200t-NB front panel does not display a brand name.
Laser Diode Properties
Material : GaAlAs
Wavelength : 780-790 nm
Emission Duration : Continuous
Laser Output Power : Less than 44.6 µW*
*
T
his output is value measured at a
distance 200mm from the objective lens
surface on the optical pick-up block.
ANSI Class : Class 1
This compact disc player is
classified as a CLASS 1
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LASER product.
The CLASS 1 LASER
PRODUCT label must be
located on the exterior.
VORSICHT : UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG
GEOFFNET. NICHT DEM STRAHL AUSSETZEN.
VARNING : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN ÄR FARLIG.
VARO! : AVATAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTINA NÄKYMÄTTÖMÄLLE LASERS TEILYLLE. ÄLÄ KATSO SÄTESSEN.
ADVARSEL : USYNLIG LASERSTRALNING VED ÅBNING NÄR SIKKERHETSAF BYDERE ER UDE AF FUNKTION. UNDGÅ UDSETTELS FOR STRÅLING.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Varningsanvisning för
laserstrålning.
❢
WARNING
W ARNING ❢
• The temperature where CDR200t is located
should be between 5ºC and 40ºC (41ºF –
104ºF), when used in a fan-cooled system.
• Do not disassemble the CDR200t cover to
reduce the risk of electric shock.
• Always remove the disc before transporting
CDR200t.
i
Important Precautions
Important Precautions
Please read the following precautions before
attempting to operate CDR200t.
• Before recording a disc, be sure to clean the disc
and CDR tray using an air aerosol-type dust
remover.
A dust particle on the disc may cause recording
to fail, producing an unuseable disc.
• Always record in a dust-free environment. If the
disc must be removed from CDR200t before
recording is finished, store the disc in a clean,
dust-free environment.
• CDR200t contains no user serviceable parts.
Refer all servicing to qualified personnel.
• If any of the following should occur, CDR200t
should be serviced by qualified personnel:
Metal objects or liquids get inside CDR200t.
CDR200t does not operate normally or a marked
change in performance is noticed.
• Do not place heavy objects on the CD-R discs.
• Do not subject CDR200t and computer to impact
or shock when in use, as this may impair recording or playback.
• Yamaha is not responsible for any data or information losses resulting from the operation of
CDR200t.
Yamaha Corporation.
This document may not, in whole or in part, be copied, photocopied, reproduced,
translated, transmitted or reduced to any electronic medium of machine readable
form without prior consent in writing from Yamaha.
MS-DOS and Windows are registered trademarks of Microsoft, Inc.
Macintosh is a registered trademark of Apple Computer, inc.
Unix is a registered trademark of UNIX System Laboratories.
All other trademarks are the property of their respective companies.
iii
ts Reserved.
■
Introduction
Thank you for purchasing a Yamaha CDR200t drive. Please read this
manual before using the drive in order to make the best use of the
superior CDR200t functions. After reading, please retain this manual
for future reference.
CDR200t Features
2xS Recording - 6xS Reading
The CDR200t is a CD-ROM recorder capable of recording at double
speed (2xS), or normal speed (1xS). It can read discs at up to 6xS.
■
Compatible with Seven Different Formats
The CDR200t can both record and read seven different formats: CDROM, CD-ROM XA, CD-I, CD-DA, CD-Bridge (multisession), CDExtra, and Video CD. The CDR200t is also equipped with an analog
audio output terminal (headphones) for CD-DA.
■
SCSI 2 for High-Volume, High-Speed Data Transfer
The CDR200t features SCSI 2, the second generation SCSI interface
for connecting computers and peripheral devices. SCSI 2 provides
high-speed transmission of large quantities of data, which is especially important when working with image data.
Introduction
■
Compatible with Windows 95 Plug and Play
SCSI IDs are set automatically by the SCAM protocol (level 1).
■
Orange Book Part 2 Compatible 5-Mode Recording
The CDR200t conforms to the five recording modes outlined in the
Orange Book Part 2: Track at Once, Multisession, Disc at Once, Session at Once, and Packet Writing.
1
Loading...
+ 15 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.