23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
SPECIFICATIONS
Tuner section
FM
Tuning rangeUS, Canadian Model:
Antenna terminalExternal antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity9 dBf
Selectivity75 dB at 400 kHz
Signal-to-noise ratio67 dB (stereo),
Harmonic distortion at 1 kHz
Separation35 dB at 1 kHz
Frequency response30 – 15,000 Hz
e Vehicle Company
Published by Sony Engineering Corporation
1
CDC-R504MP/X504MP
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
• US, Canadian model
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
• AEP, UK model
CAUTION
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
This compact disc player is classified as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
This label is located on the bottom of the chassis.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
SAFETY-RELATED COMPONENT WARNING!!
optical pick-up
semi-fixed resistor
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
CDC-R504MP/X504MP
D
Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable
CDs)
This unit can play the following discs:
Type of discsLabel on the disc
Audio CD
MP3 files
• Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
• You cannot play a CD-R/CD-RW that is not finalized∗.
• You can play MP3 files recorded on CD-ROMs, CD-Rs, and
CD-RWs.
• A CD-R/CD-RW to which a session can be added can be played.
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
∗ A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CN301) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CN301
J-2502-076-1
SERVO BOAR
CN2
3
CDC-R504MP/X504MP
TABLE OF CONTENTS
1. GENERAL
Location of Controls................................................................ 5
Connections (US, Canadian Model)........................................ 6
Connections (AEP, UK Model) ............................................... 7
2. DISASSEMBLY
2-1. Sub Panel Assy.................................................................... 9
2-2. CD Mechanism Block ......................................................... 9
2-3. Main Board ....................................................................... 10
2-4. Chassis (T) Sub Assy ........................................................10
2-5. Roller Arm Assy ................................................................ 11
3-16. IC Block Diagrams............................................................ 31
4. EXPLODED VIEWS
4-1. Main Section ..................................................................... 35
4-2. Front Panel Section ...........................................................36
4-3. CD Mechanism Section (1) ............................................... 37
4-4. CD Mechanism Section (2) ............................................... 38
4-5. CD Mechanism Section (3) ............................................... 39
4-6. CD Mechanism Section (4) ............................................... 40
5. ELECTRICAL PARTS LIST ........................................41
4
LOCATION OF CONTROLS
SECTION 1
GENERAL
CDC-R504MP/X504MP
This section is extracted
from instruction manual.
5
CDC-R504MP/X504MP
CONNECTIONS (US, Canadian Model)
6
CONNECTIONS (AEP, UK Model)
CDC-R504MP/X504MP
7
CDC-R504MP/X504MP
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET
2-1.SUB PANEL ASSY
(Page 9)
2-2.CD MECHANISM BLOCK
(Page 9)
2-3.MAIN BOARD
(Page 10)
2-7.OPTICAL PICK-UP
(Page 12)
2-4.CHASSIS (T) SUB ASSY
(Page 10)
2-5.ROLLER ARM ASSY
(Page 11)
2-6.CHASSIS (OP) ASSY
(Page 11)
2-8.SL MOTOR ASSY (M902)
(Page 12)
2-10. SERVO BOARD
(Page 13)
2-9.LE MOTOR ASSY (M903)
(Page 13)
8
Note : Follow the disassembly procedure in the numerical order given.
s
)
2-1. SUB PANEL ASSY
3
two claws
CDC-R504MP/X504MP
1
two
screws
(+PTT 2.6
x
6)
2-2. CD MECHANISM BLOCK
5
CD mechanism block
4
sub panel assy
7
bracket (CD)
6
two
screws
(+PTT 2.6
2
two claw
x
4)
2
screw
(+PTT 2.6
x
6)
3
4
CN301
1
screw
(+PTT 2.6
x
6
9
CDC-R504MP/X504MP
)
2-3. MAIN BOARD
1
three ground point screws
(+PTT 2.6
3
MAIN board
x
6)
2
two
screws
x
(+PTT 2.6
insulating sheet
6
2-4. CHASSIS (T) SUB ASSY
2
two
screws
(+P 1.7
5
SENSOR board
3
claw
x
2.2)
4
claw
1
two
screws
x
(+P 1.7
6
2.2)
chassis (T) sub assy
10
2-5. ROLLER ARM ASSY
4
worm wheel (RA)
1
spring (RAL)
3
washer (0.8-2.5)
5
roller arm assy
2
spring (RAR)
CDC-R504MP/X504MP
2-6. CHASSIS (OP) ASSY
0
coil spring (damper)
4
washer
5
gear (LE1)
lever (D)
6
8
qa
chassis (OP) assy
1
CN1
9
two coil springs (damper)
7
slider (R)
2
Remove the six solderings.
3
tension coil spring (KF)
11
CDC-R504MP/X504MP
)
2-7. OPTICAL PICK-UP
5
claw
2
chucking arm sub assy
1
tension coil spring (CHKG
7
optical pick-up
2-8. SL MOTOR ASSY (M902)
6
main shaft
4
rack (SL)
3
screw
(+B 1.4
x
5)
12
2
SL motor assy (M902)
1
screw
(+P 1.4
x
1.8)
2-9. LE MOTOR ASSY (M903)
qf
two toothed lock
(+M 1.4
bracket (LEM)
qs
(+M 1.7
screw
x
)
screws
2.5)
6
screw
(+P 1.7
x
qd
2.2)
qa
screw
(+M 1.7
qg
(M903)
0
woam (LEB) assy
x
2.5)
LE motor assy
7
leaf spring (LE)
8
screw
(+M 1.7
9
bearing (LEB)
2
washer
gear (LE1)
3
lever (D)
x
CDC-R504MP/X504MP
2.5)
4
5
slider (R)
2-10. SERVO BOARD
1
Remove the eight solderings.
1
Remove the soldering.
6
SERVO board
2
Remove the three solderings.
4
toothed lock
(M 1.7)
5
screw
claw
3
CN1
13
CDC-R504MP/X504MP
SECTION 3
DIAGRAMS
3-1. IC PIN DESCRIPTIONS
• IC3 CXD3059AR (DIGIT AL SER VO/DIGITAL SIGNAL PROCESSOR) (SERVO BOARD (1/2))
Pin No.Pin NameI/OPin Description
1MIRRI/OMirrer signal input/output
2DFCTI/ODefect signal input/output
3FOKI/OFocus OK signal input/output
4VSS—Ground pin
5LOCKI/ONot used in this set. (Open)
6MDPOSpindle motor servo control signal output
7SSTPIDisc most inner detection signal input
8IOVSS1—Digital ground pin for I/O
9SFDROSled drive signal output
10SRDROSled drive signal output
11TFDROTracking drive signal output
12TRDROTracking drive signal output
13FFDROFocus drive signal output
14FRDROFocus drive signal output
15IOVDD1—Digital power supply pin for I/O
16AVDD0—Analog power supply pin for I/O
17AVSS0—Analog ground pin
18NC—Not used. (Open)
19EIE signal input
20FIF signal input
21TEIITracking error signal input from the DSSP block
22TEOOTracking error signal output to the RF amp block
23FEIIFocus error signal input from the DSSP block
24FEOOFocus error signal output form the RF amp block
25VCI/O
26AIA signal input
27BIB signal input
28CIC signal input
29DID signal input
30NC—Not used. (Open)
31AVDD4—Analog power supply pin
32RFDCOI/O
33PDSENSIReference voltage input for PD
34AC SUMORFAC suming amp signal output
35EQ INIEqualizer circuit signal input
36LDOAPC amp signal output
37PDIAPC amp signal input
38NC—Not used. (Open)
39RFCIEQ cut off frequency adjustment input
40AVSS4—Analog ground pin
41RFACOORFAC signal output
42RFACIIRFAC signal input or EFM signal input
43AVDD3—Analog power supply pin
44BIASIAsymmetry circuit constant current input
45ASYIIAsymmetry comparate voltage input
46ASYOOEFM full swing signal output
47VPCOOCharge pomp output for wideband EFM PLL
48VCTLIVCO2 control voltage input for wideband EFM PLL
49AVSS3—Analog ground pin
VC voltage output to the RF amp block
Center voltage input from the DSSP block by command select
RFDC signal output
RFDC signal input from the DSSP block by command select
14
CDC-R504MP/X504MP
Pin No.Pin NameI/OPin Description
50CLTVIVCO1 control voltage input
51FILOOFilter signal output for master PLL
52FILIIFilter signal input for master PLL
53PCOOCharge pomp output for master PLL
54AVDD5—Analog power supply pin
55DDVROUTODC/DC converter output
56DDVRSENIDC/DC converter output voltage monitor signal input
57AVSS5—Analog ground pin
58DDCRIReset signal input for DC/DC converter
59NC—Not used. (Open)
60BCKIID/A interface bit clock signal input
61PCMDIID/A interface serial data signal input
62LRCKIID/A interface LR clock signal input
63LRCKOD/A interface LR clock signal output
64VSS—Digital ground pin for internal
65PCMDOD/A interface serial data signal output
66BCKOD/A interface bit clock signal output
67VDD—Digital power supply pin for internal
68EMPHONot used in this set. (Open)
69EMPHIINot used in this set. (Fixed at “L”.)
70IOVDD2—Digital power supply pin for I/O
71DOUTODigital out signal output
72, 73TESTITest pin Normally “L”.
74IOVSS2—Digital ground pin for I/O
75NC—Not used in this set. (Open)
76XVSS—Ground pin for master clock
77XTAOOCrystal oscillation circuit output (16.9344 MHz)
78XTAIICrystal oscillation circuit input (16.9344 MHz)
79XVDD—Power supply pin for master clock
80AVDD1—Analog power supply pin
81AOUT1OL channel analog signal output
82VREFLOL channel reference voltage output
83AVSS1—Analog ground pin
84AVSS2—Analog ground pin
85VREFROR channel reference voltage output
86AOUT2OR channel analog signal output
87AVDD2—Analog power supply pin
88NC—Not used. (Open)
89IOVDD0—Digital power supply pin for I/O
90RMUTOR channel “O” detection flug output
91LMUTOL channel “O” detection flug output
92NC—Not used. (Open)
93XTSLIX’tal select signal input 16.9344 MHz: “L”, 33.8688 MHz: “H”
94IOVSS0—Digital ground pin for I/O
95XTACNIOscillation circuit control input “H”: Oscillation start, “L”: Oscillation stop
96SQSOOSub 80 bit and PCM peak, level data signal output CD text data signal output
97SQCKIClock signal input for SQSO read out
98SBSOOSub P-W serial data signal output Not used in this set. (Open)
99EXCKIClock signal input for SBSO read out Not used in this set. (Open)
100XRSTISystem reset signal input “L”: reset
101SYSMIMute signal input “H”: mute Not used in this set. (Fixed at “L”.)
102DATAISerial data signal input
103VSS—Digital ground pin for internal
15
CDC-R504MP/X504MP
Pin No.Pin NameI/OPin Description
104XLATILatch signal input
105CLOKISerial data transfer clock signal input
106VDD—Digital power supply pin for internal
107SENSOSENS signal output
108SCLKIClock signal input for SENS serial data read out
109ATSKI/OInput/output for anti-shock
110WFCKOWFCK signal output Not used in this set. (Open)
111XUGFOXUGF signal output Not used in this set. (Open)
112XPCKOXPCK signal output Not used in this set. (Open)
113GFSOGFS signal output
114C2POOC2PO signal output
115SCOROSub cord sync signal output
116VDD—Digital power supply pin for internal
117C4MO4.2336 MHz signal output Not used in this set. (Open)
118WDCKOWord clock signal output Not used in this set. (Open)
119COUTI/OTrack count signal input/output Not used in this set. (Open)
120NC—Not used. (Open)
1DAVDD—Power supply pin for D/A output converter (+3.3 V)
2BBE-MPONot used in this set. (Open)
3DAVSS—Ground pin for D/A output converter
4 to 6NCOONot used in this set. (Open)
7UNISOOSONY-BUS data signal output
8UNISIISONY-BUS data signal input
9UNICKOOSONY-BUS clock signal output
10VDD1—Power supply pin for internal core (+3.3 V)
11MMODIFlash microcomputer write detection signal input Not used in this set.
12OSCOUTOHigh speed operation clock signal output (27 MHz)
13OSCINIHigh speed operation clock signal input (27 MHz)
14VSS1—Ground pin for internal core
15XINILow speed operation clock signal input (32.768 kHz)
16XOUTOLow speed operation clock signal output (32.768 kHz)
17VDD2—Power supply pin for internal core (+3.3 V)
18MOD1—Pull up: “H”
19RESETIReset signal input
20NCOONot used in this set. (Open)
21ACC INIAccessory power supply detection signal input
22TEST INITest mode detection signal input
23TEL ATTITelephone attenuate detection signal input
24ATTOAudio mute control signal output
25XKEYONOKey power supply control signal output Not used in this set. (Open)
26NCOONot used in this set. (Open)
27KEYACKIKey acknowledge detection signal input
28TU ATTINITuner mute ZERO cross detection signal input
29, 30NCOONot used in this set. (Open)
31BUINIBack up power supply detection signal input
32 to 35NCOONot used in this set. (Open)
36BUSONOBUS on signal output
37SYSRSTOSystem reset signal output
38EJECT OKOCD servo IC eject OK signal output
39 to 41NCOONot used in this set. (Open)
42Z MUTEIMechadeck mute zero cross detection signal input L/R
43 to 46NCOONot used in this set. (Open)
47CD ONICD mechanism power supply control signal input (“H”: Power on)
48CDM ONICD mechanism deck power supply control signal input (“H”: Power on)
49, 50NCOONot used in this set. (Open)
51AREASEL1IDestination function setting input 1
52AREASEL2IDestination function setting input 2
53AREASEL3IDestination function setting input 3
54LCD CTLO
55, 56NCOONot used in this set. (Open)
57DSSAODSSA on/off change signal output (Cut off rear)
58PANEL SWIFront panel attachment detection signal input “L”: with panel, “H”: without panel
59DIAGICondition signal input from the power IC
60VOLATTOElectronic volume attenuate control signal output
61, 62NCOONot used in this set. (Open)
63VSS2—Ground pin for I/O port
64TU ATTOTuner mute control signal output
65NCOONot used in this set. (Open)
“H” output: LCD unit and key confusion, power off
“L” output: LCD unit and key confusion, power on
17
CDC-R504MP/X504MP
Pin No.Pin NameI/OPin Description
66NS MASKONoise mask signal output
67EEP CKOOSerial clock signal output for EEPROM communication
68EEP SIOI/OSerial data signal input/output for EEPROM communication
69NCOONot used in this set. (Open)
70AMPSTBOPower regulator IC standby signal output
71 to 73NCOONot used in this set. (Open)
74NCOONot used in this set.
75NCOONot used in this set. (Open)
76LCDSOOSerial data signal output to the LCD driver
77LCDCEOChip enable signal output to the LCD driver
78LCDCKOOSerial clock signal output to the LCD driver
79I2C SIOI/OI2C BUS serial data signal input/output
80NCOONot used in this set. (Open)
81I2C CKOOI2C BUS serial clock signal output
82DAVNIRDS data block synchronization detection signal input
83SIRCSIRemote control signal input
84NCOONot used in this set. (Open)
85BEEPOBeep signal output to the power amp
86 to 88NCOONot used in this set. (Open)
89VDD3—Power supply pin for I/O port (+3.3 V)
90NCOONot used in this set. (Open)
91VSS3—Ground pin for I/O port
92QUALITYINoise detection signal input
93VSMIS meter voltage detection signal input
94KEYIN1IKey signal input 1
95KEYIN0IKey signal input 0
96NCOONot used in this set.
97KEYIN2IKey signal input (EJECT, OFF, SOURCE switch)
98REIRotary encoder signal input
99L METERILevel meter voltage detection signal input
3-6. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS3-7. WAVEFORMS
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
f
•
• C : panel designation.
• A : B+ Line.
• B : B– Line.
• H : adjustment for repair.
•Voltages and waveforms are dc with respect to ground
• CD mechanism section
no mark : CD PLAY
• Main (1/2), (2/2) and Display sections
no mark : FM
: internal component.
Note:
The components identified by mark 0 or dotted
line with mark 0 are criti-
cal for safety.
Replace only with part
number specified.
under no-signal (detuned) conditions.
(): AM
<>: CD PLAY
4
W or less unless otherwise
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
∗: Impossible to measure
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J: CD PLAY
F: FM
f: AM/MW/LW
a : AUX
• Abbreviation
CND : Canadian model.
For printed wiring boards.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
a
•
•: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A)parts face are indicated.
• Abbreviation
: Through hole.
C
Q
These are omitted
EB
E
CB
These are omitted
C
BE
These are omitted
CND : Canadian model.
— Servo Board —
(MODE: CD PLAY)
1
Approx. 100mVp-p
IC3 wa (TEI)
2
Approx. 100mVp-p
IC3 wd (FEI)
3
IC3
(A), wk (C)
wh
4
IC3
(B), wl (D)
wj
5
IC3
(RFACO)
ra
6
16.9344MHz
IC3
(XTAO)
uj
7
0V
0V
Approx.
150mVp-p
Approx.
150mVp-p
Approx.
0.8Vp-p
2Vp-p
1Vp-p
— Main Board —
1
27MHz
IC501 qs (OSCOUT)
2
32.768kHz
qg
(XIN)
IC501
3
q;
(XTO)
IC51
2.2Vp-p
1.8Vp-p
0.9Vp-p
18.43MHz
ia
(X1)
IC4
2222
3-8. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 21 for Circuit Boards Location. : Uses unleaded solder.
CDC-R504MP/X504MP
A
B
C
D
E
F
G
H
1
Q6
C83
C74
C85
R116
R149
C92
R145
R142
R143
R141
R140
R85
C1
C2
R117
234567891011121314
Q5
R107
C22
C24
C42
C81
R39
R148
R70
R22
R24
C60
R37
R147
C39
R42
C23
R23
C25
C30
R25
C34
R41
R43
R55
R54
C50
C57
C107
X2
R146
C35
R124
R133
C32
R38
C40
C38
C49
R61
C64
C46
C47
C6
R12
FB2
R49
C63
Q1
C10
R72
C37
R45
R53
R79
C48
R7
R44
R46
C44
C43
C65
FMB7
R1
C4
CN1
C5
FMB8
R101
R139
R106
IC7
IC8
R111
C75
R64
C56
R18
R123
C19
C91
C115
C86
Q3
R110
IC4
Q2
C33
R126
C77
R40
R109
R92
R56
C58
C54
R52
R91
R16
R29
R50
R47
C36
R60
C29
C28
C41
R77
X1
C59
R48
R136
R114
R5
C8
C27
R68
R76
CN2
R6
BP2
R13
BP3
IC3
C55
R78
C53
R98
C52
R97
R65
FB5
R4
C7
C26
R26
R57
R81
R119
R62
R73
R27
C45
R129
R59
R67
R9
R21
R3
R19
R28
R115
R17
C18
C67
R128
R71
R74
R69
R2
FB1
C79
R127
R87
R80
R8
R20
R108
C51
R86
BP1
R122
C66
C110
R99
R144
C109
SW3
SW2
(Page 28)
C21
C3
R14
R15
C11
IC1
C13
C16
R10
C14
SW1
R11
2323
• Semiconductor
Location
Ref. No.Location
IC1G-2
IC3C-10
IC4E-2
IC7B-2
IC8C-2
Q1B-4
Q2B-2
Q3B-2
Q5A-2
Q6A-2
CDC-R504MP/X504MP
3-9. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 22 for Waveforms.
C45
R50
TP94
TP96
C35
TP97
R38
R40
C41
R52
TP116
TP98
TP99
C37C34
C39
R41
C38
TP127
IC3
R42
R43
R45
C42
C40
R49
R44
C44
C43
R46
TP137
C46
TP141
R53
R59
R56
R67
R60
R71
C54
TP180
C52
C58
C53
C59
TP181
C81
R70
TP167C55
TP175
R68
R72
C50
R61
R54
R55
C47
C49
C48
C107
C65
C64
R77
X1
C57
R78
R76
R79
R97
C60
R98
CN2
TP129
TP72
TP123
TP128
TP139
TP53
TP56
R65
TP55
TP54
R114
R133
R124
TP48
TP49
TP47
TP133
TP135
TP42
TP51
TP37
TP41
TP132
TP136
TP46
TP36
TP39
TP38
TP43
TP40
(Page 26)
FB2
FB5
R48
R149
C33
TP63
TP62
TP343
TP344
TP65
TP59
TP60
TP57
R64
TP61
R29
C29
C28
TP140
R13
R6
BP2
C22
C23
CN1
TP21
TP22
TP23
TP24
TP25
TP26
C4
TP27
TP28
TP29
TP30
R1
TP32
TP33
C5
TP34
TP35
C24
C25
R22
R24
TP71
BP3
R25
R23
C6
TP50
C27
Q1
TP44TP45
R12R7
C30
C10
(Page 25)
2424
• Refer to page 22 for Waveform.
3-10. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 31 for IC Block Diagrams.
CDC-R504MP/X504MP
(Page 24)
FB1
SW3
SW2
SW1
M903
M901
M902
TP7
TP8
TP9
TP11
TP12
TP19
TP20
TP17
TP18
TP13
TP14
TP15
TP16
R69
R147
IC4
R127
R57
R128
R129
R146
TP52
R62
C51
R119
C36
R136
C63SW4
IC B/D
R117
X2
R37
C32
C21
R18
C19
R20
R19
R17
C18
R123
TP58
R21
C26
R16
R10
R28
R27R26
C7
R4
R2
R3
C8
R5
C13
R14R15
C1
C2
C3
C11
C16
R9
C14
R11
IC1
R8
R47
R39R73
R148
R126
R122
C67C56
R81
R85
R86
R87
R140
C66
R145
R141
R142
R143
TP31
R74
R80
R115
R91
R92
C86
C115
R110
C75
R144
R108
R109
R99
C77
TP226
C79
TP230
TP231
TP249
R111
C91
C92
C109
IC8
C110
R116
BP1
IC B/D
C83
R107
Q6
C74
IC7
C85
Q3Q5
R106R101
R139
Q2
2525
CDC-R504MP/X504MP
3-11. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 32 for IC Block Diagrams.
• Refer to page 22 for Waveforms.
IC401
JC26
R519
R573
IC B/D
R539
R405
R406
R408
R407
R409
C411
C410
R410
R411
R402
R636
R531
R563
R559
R564
R560
C427
C412
R429
R428
C416
Q403
C415
Q402
D503
(Page 27)
C509
TU1
R51
J1
Q3
C3
C4
C1
C2
C6
D1
C5
R5R4
R1
Q1
R16
R15
C9
R10
R8
R6
R7
R9
L1
C53
C54
IC51
R58
C62
IC B/D
C407
C402
R59
C51
C52
Q51
C58
R52
C57
C55
C56
R56
R57
R53
R55
C60C59
R540
R54
X51
Q52
R61
Q503
R557
R520
R537
R532
R530
R528
C405
D402
C404
C403
C406
R538
R419
C429
R549
D401
C419
R534
R418
C420
C428
Q401
C430
C401
R12
R11
R422
R421
C8
C7
R415
R416
R417
R401
C426
C425
C408
R414
R413
C409
(Page 24)
CN301
L304
L305
L306
C304
C301 C305
C302
L310
C308
C310
D301
C309
C303
L308
L309
C307
JC19
JW144
JW145
L303
L307
L302
R303
JW143
JW142
R521R522
R544
R592
R567
R558
R551
C515
R506
X502
C512
R508
C514
C502
C504
R579
R591
C508
C507
C517
C503
X501
D587
D586
R535
R593
R543
R556
R552
R503 R565
R505 R566
C513
R547
R509
IC501
C501
R512
R510
R513R514
R511
R541
R518
C516
C510
C511
R501R596R502
R504
R595
2626
3-12. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 34 for IC Block Diagram.
C441
C461
C431
R441
R461
R431
R442
R462
R432
Q441
Q461
Q431
C765 C766C764
C751
C750
D751
D753
D755
D757
C333
C334
CDC-R504MP/X504MP
J331
(Page
26)
C451
C481
C471
R451
R481
R471
R452
R482
R472
Q451
Q481
Q471
Q491
Q492
R492
R491
C491
D492
D491
R443 C442
R463 C462
R433 C432
R453 C452
R493
C492
C756R756
C753
R752
C755
C754
IC750
IC B/D
C761
C758
C759
C760
D759
D760
D752
D754
D756
D758
D761
D762
R609
C701
D609
C602 C601
C617
C618
C630
C628
C626
C624
D601
C631
C629
C627
CN601
FU601
C625
L601
IC602
C621
L501
C632
R631
R632
Q581
Q631Q651
R584
Q582
R633
R634
R585D580
Q580
C703
D581
JW53
R582
R583
S702
R653
R654
C623
JC2
L502
C622
D651
R652
R651
D703
D702
R701
R731R732
L374L373L372
R735
L731
R734
C732
C731
R733
D731
CN701
(Page 30)
D711
D712
C704
2727
CDC-R504MP/X504MP
3-13. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 21 for Circuit Boards Location. : Uses unleaded solder.
583-262-380-01 ILLUMINATOR (LCD)
593-262-374-01 GUIDE (VOLUME), LIGHT
601-861-209-11 AUX BOARD
613-262-355-01 PANEL, FRONT BACK
62X-3384-688-1 CASE ASSY (for FRONT PANEL)
101A-3372-444-A CHASSIS (T) SUB ASSY
1023-253-729-11 SPRING (LTR), TENSION COIL
1033-257-892-11 SPRING (DAMPER), COIL
1043-257-892-01 SPRING (DAMPER), COIL
1053-253-695-11 SPRING (KF), TENSION COIL
IC9016-705-180-01 IC LC75827W
IC9716-600-163-01 IC RS-770 (IR)
< JUMPER RESISTOR >
JC9031-216-864-11 METAL CHIP05%1/10W
LED901 6-500-476-01 LED SML310BA1TT86 (MENU)
LED902 6-500-476-01 LED SML310BA1TT86 (MENU)
LED903 6-500-476-01 LED SML310BA1TT86 (OFF)
LED904 6-500-476-01 LED SML310BA1TT86
(+ >M, m . –)
LED905 6-500-476-01 LED SML310BA1TT86 (1)
LED906 6-500-476-01 LED SML310BA1TT86 (MENU)
LED907 6-500-476-01 LED SML310BA1TT86 (PTY,AF/TA)
LED908 6-500-476-01 LED SML310BA1TT86 (MENU)
LED909 6-500-476-01 LED SML310BA1TT86 (4)
LED910 6-500-476-01 LED SML310BA1TT86 (3)
LED911 6-500-476-01 LED SML310BA1TT86 (2)
LED912 6-500-476-01 LED SML310BA1TT86 (5)
LED913 6-500-476-01 LED SML310BA1TT86 (6)
LED914 6-500-476-01 LED SML310BA1TT86 (ATT)
LED915 6-500-476-01 LED SML310BA1TT86 (EQ)
LED916 6-500-476-01 LED SML310BA1TT86 (DSPL)
LED917 6-500-476-01 LED SML310BA1TT86 (H-BASS)
LED918 6-500-476-01 LED SML310BA1TT86 (BTM/SENS)
LED919 6-500-476-01 LED SML310BA1TT86 (SOURCE,MODE)
LED920 6-500-476-01 LED SML310BA1TT86 (Z)
LED921 6-500-855-01 LED CL-490S-WF-SD-TS (LCD BACK LIGHT)
LED922 6-500-855-01 LED CL-490S-WF-SD-TS (LCD BACK LIGHT)
< TRANSISTOR >
Q9018-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
R9011-216-194-00 METAL CHIP6805%1/8W
R9021-216-819-11 METAL CHIP6805%1/10W
R9031-216-194-00 METAL CHIP6805%1/8W
R9041-216-819-11 METAL CHIP6805%1/10W
R9051-216-819-11 METAL CHIP6805%1/10W
R9061-216-821-11 METAL CHIP1K5%1/10W
R9071-216-823-11 METAL CHIP1.5K5%1/10W
R9081-216-823-11 METAL CHIP1.5K5%1/10W
R9091-216-825-11 METAL CHIP2.2K5%1/10W
R9101-216-194-00 METAL CHIP6805%1/8W
R9111-216-819-11 METAL CHIP6805%1/10W
R9121-216-819-11 METAL CHIP6805%1/10W
R9131-216-821-11 METAL CHIP1K5%1/10W
R9141-216-823-11 METAL CHIP1.5K5%1/10W
R9151-216-823-11 METAL CHIP1.5K5%1/10W
R9161-216-825-11 METAL CHIP2.2K5%1/10W
R9171-216-827-11 METAL CHIP3.3K5%1/10W
R9181-218-867-11 METAL CHIP6.8K5%1/10W
R9191-216-825-11 METAL CHIP2.2K5%1/10W
R9201-216-825-11 METAL CHIP2.2K5%1/10W
R9211-216-017-00 RES-CHIP475%1/10W
R9221-216-295-11 SHORT CHIP0
R9311-216-033-00 METAL CHIP2205%1/10W
R9321-216-033-00 METAL CHIP2205%1/10W
R9331-216-033-00 METAL CHIP2205%1/10W
R9341-216-033-00 METAL CHIP2205%1/10W
R9351-216-033-00 METAL CHIP2205%1/10W
R9361-216-033-00 METAL CHIP2205%1/10W
R9371-216-033-00 METAL CHIP2205%1/10W
R9381-216-033-00 METAL CHIP2205%1/10W
R9391-216-033-00 METAL CHIP2205%1/10W
R9401-216-033-00 METAL CHIP2205%1/10W
R9501-216-808-11 METAL CHIP825%1/10W
R9511-216-821-11 METAL CHIP1K5%1/10W
R9521-216-824-11 METAL CHIP1.8K5%1/10W
R9531-216-824-11 METAL CHIP1.8K5%1/10W
R9711-216-049-11 RES-CHIP1K5%1/10W
R9721-216-821-11 METAL CHIP1K5%1/10W
R9811-216-295-11 SHORT CHIP0
R9821-216-295-11 SHORT CHIP0
R9831-216-295-11 SHORT CHIP0
R9841-216-801-11 METAL CHIP225%1/10W
R9851-216-801-11 METAL CHIP225%1/10W
R9861-216-801-11 METAL CHIP225%1/10W
R9871-216-811-11 METAL CHIP1505%1/10W
R9881-216-811-11 METAL CHIP1505%1/10W
R9911-216-864-11 METAL CHIP05%1/10W
R9921-216-840-11 METAL CHIP39K5%1/10W
R9931-216-857-11 METAL CHIP1M5%1/10W
R9941-216-827-11 METAL CHIP3.3K5%1/10W
R9951-216-827-11 METAL CHIP3.3K5%1/10W
R9961-216-827-11 METAL CHIP3.3K5%1/10W
IC516-803-747-01 IC TDA7333-013TR (R504MP)
IC4016-705-518-01 IC BD3809FS-FE2
IC5016-804-065-01 IC MN101E01KSH
IC6028-759-659-13 IC PST3428UL
IC7506-705-360-01 IC TDA8588BJ/N2
< JACK >
J11-815-185-13 JACK (ANTENNA)
J3311-774-698-11 JACK, PIN 2P (AUDIO OUT REAR)
< JUMPER RESISTOR >
JC21-216-864-11 METAL CHIP05%1/10W
JC61-216-296-11 SHORT CHIP0
JC71-216-864-11 METAL CHIP05%1/10W
JC101-216-864-11 METAL CHIP05%1/10W
JC111-216-864-11 METAL CHIP05%1/10W
JC131-216-864-11 METAL CHIP05%1/10W
JC141-216-296-11 SHORT CHIP0
JC171-216-296-11 SHORT CHIP0
JC181-216-296-11 SHORT CHIP0
JC191-216-296-11 SHORT CHIP0
JC201-216-864-11 METAL CHIP05%1/10W
JC221-216-864-11 METAL CHIP05%1/10W
JC241-216-296-11 SHORT CHIP0
JC251-216-864-11 METAL CHIP05%1/10W
JC261-216-296-11 SHORT CHIP0
R4061-216-811-11 METAL CHIP1505%1/10W
R4071-216-811-11 METAL CHIP1505%1/10W
R4081-216-811-11 METAL CHIP1505%1/10W
R4091-216-811-11 METAL CHIP1505%1/10W
R4101-216-809-11 METAL CHIP1005%1/10W
R4111-216-809-11 METAL CHIP1005%1/10W
R4131-216-845-11 METAL CHIP100K5%1/10W
R4141-216-845-11 METAL CHIP100K5%1/10W
R4151-216-857-11 METAL CHIP1M5%1/10W
R4161-216-832-11 METAL CHIP8.2K5%1/10W
R4171-216-827-11 METAL CHIP3.3K5%1/10W
R4181-216-833-11 METAL CHIP10K5%1/10W
R4191-216-857-11 METAL CHIP1M5%1/10W
R4281-216-845-11 METAL CHIP100K5%1/10W
R4291-216-845-11 METAL CHIP100K5%1/10W
R4311-216-809-11 METAL CHIP1005%1/10W
R4321-216-841-11 METAL CHIP47K5%1/10W
R4331-216-864-11 METAL CHIP05%1/10W
R4411-216-809-11 METAL CHIP1005%1/10W
R4421-216-841-11 METAL CHIP47K5%1/10W
R4431-216-864-11 METAL CHIP05%1/10W
R4511-216-809-11 METAL CHIP1005%1/10W
R4521-216-841-11 METAL CHIP47K5%1/10W
R4531-216-864-11 METAL CHIP05%1/10W
R4611-216-809-11 METAL CHIP1005%1/10W
R4621-216-841-11 METAL CHIP47K5%1/10W
R4631-216-864-11 METAL CHIP05%1/10W
R4711-216-809-11 METAL CHIP1005%1/10W
R4721-216-841-11 METAL CHIP47K5%1/10W
R4811-216-809-11 METAL CHIP1005%1/10W
R4821-216-841-11 METAL CHIP47K5%1/10W
R4911-216-857-11 METAL CHIP1M5%1/10W
R4921-216-864-11 METAL CHIP05%1/10W
R4931-216-805-11 METAL CHIP475%1/10W
R5011-216-864-11 METAL CHIP05%1/10W
R5021-216-809-11 METAL CHIP1005%1/10W
R5031-216-809-11 METAL CHIP1005%1/10W
R5041-218-871-11 METAL CHIP10K0.5%1/10W
R5051-218-871-11 METAL CHIP10K0.5%1/10W
R5061-216-845-11 METAL CHIP100K5%1/10W
R5081-216-813-11 METAL CHIP2205%1/10W
R5091-216-864-11 METAL CHIP05%1/10W
R5101-216-801-11 METAL CHIP225%1/10W
R5111-216-801-11 METAL CHIP225%1/10W
R5121-216-801-11 METAL CHIP225%1/10W
R5131-216-845-11 METAL CHIP100K5%1/10W
R5141-216-845-11 METAL CHIP100K5%1/10W
R5181-249-417-11 CARBON1K5%1/4W
R5201-216-845-11 METAL CHIP100K5%1/10W
R5211-216-825-11 METAL CHIP2.2K5%1/10W
R5221-216-825-11 METAL CHIP2.2K5%1/10W
R5281-216-845-11 METAL CHIP100K5%1/10W
R5301-216-845-11 METAL CHIP100K5%1/10W
R5311-216-845-11 METAL CHIP100K5%1/10W
R5321-216-845-11 METAL CHIP100K5%1/10W
R5371-216-845-11 METAL CHIP100K5%1/10W
(X504MP)
R5381-216-845-11 METAL CHIP100K5%1/10W
(R504MP)
R5391-216-864-11 METAL CHIP05%1/10W
R5401-216-864-11 METAL CHIP05%1/10W
R5411-216-845-11 METAL CHIP100K5%1/10W
R5431-216-845-11 METAL CHIP100K5%1/10W
R5441-216-821-11 METAL CHIP1K5%1/10W
R5471-216-864-11 METAL CHIP05%1/10W
R5491-216-845-11 METAL CHIP100K5%1/10W
(X504MP:AEP,UK)
R5511-216-845-11 METAL CHIP100K5%1/10W
(R504MP/X504MP:US,CND)
R5521-216-864-11 METAL CHIP05%1/10W
R5561-216-864-11 METAL CHIP05%1/10W
R5571-216-809-11 METAL CHIP1005%1/10W
R5581-216-845-11 METAL CHIP100K5%1/10W
(X504MP)
R5591-216-845-11 METAL CHIP100K5%1/10W
R5601-216-845-11 METAL CHIP100K5%1/10W
(US,CND)
R5631-216-845-11 METAL CHIP100K5%1/10W
R5641-216-845-11 METAL CHIP100K5%1/10W
(AEP,UK)
R5651-216-809-11 METAL CHIP1005%1/10W
R5661-218-871-11 METAL CHIP10K0.5%1/10W
R5671-216-833-11 METAL CHIP10K5%1/10W
(R504MP)
R5731-216-864-11 METAL CHIP05%1/10W
R5791-216-809-11 METAL CHIP1005%1/10W
R5821-216-821-11 METAL CHIP1K5%1/10W
R5831-216-821-11 METAL CHIP1K5%1/10W
R5841-216-849-11 METAL CHIP220K5%1/10W
R5851-216-849-11 METAL CHIP220K5%1/10W
R5911-216-809-11 METAL CHIP1005%1/10W
R5921-216-864-11 METAL CHIP05%1/10W
(R504MP)
R5931-216-864-11 METAL CHIP05%1/10W
R5951-216-833-11 METAL CHIP10K5%1/10W
R5961-216-864-11 METAL CHIP05%1/10W
R6091-249-417-11 CARBON1K5%1/4W
R6311-249-425-11 CARBON4.7K5%1/4W
R6321-216-841-11 METAL CHIP47K5%1/10W
R6331-216-841-11 METAL CHIP47K5%1/10W
R6341-216-829-11 METAL CHIP4.7K5%1/10W
R6361-216-845-11 METAL CHIP100K5%1/10W
R6511-216-821-11 METAL CHIP1K5%1/10W
(AEP,UK)
R6521-249-437-11 CARBON47K5%1/4W
(AEP,UK)
R6531-216-833-11 METAL CHIP10K5%1/10W
(AEP,UK)
R6541-216-833-11 METAL CHIP10K5%1/10W
R7011-249-401-11 CARBON475%1/4W
R7311-249-417-11 CARBON1K5%1/4W
R7321-249-417-11 CARBON1K5%1/4W
R5341-216-833-11 METAL CHIP10K5%1/10W
R5351-216-845-11 METAL CHIP100K5%1/10W
R7331-216-834-11 METAL CHIP12K5%1/10W
R7341-216-834-11 METAL CHIP12K5%1/10W
R7351-216-820-11 METAL CHIP8205%1/10W
FB11-216-864-11 METAL CHIP05%1/10W
FB21-216-864-11 METAL CHIP05%1/10W
FB51-216-864-11 METAL CHIP05%1/10W
< IC >
IC16-705-366-01 IC LA6560-TE-L-E
IC38-753-216-86 IC CXD3059BR
IC46-804-028-01 IC MB90487PFV-G-105-BNDE1
IC76-705-364-01 IC R1114N151D-TR-FA
IC86-705-365-01 IC TC94A34FG-002
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
MEMO
CDC-R504MP/X504MP
49
CDC-R504MP/X504MP
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.DateDescription of Revision
1.02004. 01New
50
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.