Yamaha CD-1330 Service manual

MICRO COMPONENT SYSTEM
MCS-1330
CD PLAYER
CD-1330
The MCS-1330 consists of the R-1330, CD-1330 and NS-BP400. This service manual is for the CD-1330. For service manual of the R-1330 and NS-BP400, please refer to the following publication number:
R-1330/NS-BP400: 101127
MCS-1330 は、R-1330、CD-1330 および NS-BP400 で構成されています。 このサービスマニュアルは CD-1330 用です。
R-1330、NS-BP400 用のサービスマニュアルは下記管理ナンバーを参照してください。
R-1330/NS-BP400: 101127
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known and understood by the users, and have therefore not been restated.
WARNING:
IMPORTANT:
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifi cations are subject to change without notice or obligation to retrofi t. Should any discrepancy appear to exist, please contact the distributor's Service Division.
WARNING:
IMPORTANT:
Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury,
destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative.
The presentation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
CONTENTS
TO SERVICE PERSONNEL ........................................2–4
PREVENTION OF ELECTROSTATIC DISCHARGE ......5
SYSTEM COMPOSITION /
FRONT PANEL ...............................................................6
REAR PANELS ...........................................................7–8
SPECIFICATIONS /
INTERNAL VIEW .......................................................... 10
DISASSEMBLY PROCEDURES / TEST MODE / UPDATING FIRMWARE /
ファームウェアの書き込み
テストモード
システム構成
参考仕様
.........................................9
...................................14–15
.....................................16–20
....................... 6
分解手順
........... 11–13
IMPORTANT NOTICE
DISPLAY DATA .............................................................21
IC DATA ...................................................................22–27
PIN CONNECTION DIAGRAMS .............................28–29
BLOCK DIAGRAM ........................................................ 31
PRINTED CIRCUIT BOARDS .................................32–38
SCHEMATIC DIAGRAMS ....................................... 39–41
REPLACEMENT PARTS LIST ................................ 43–53
REMOTE CONTROL .....................................................54
101130
Copyright © 2008 All rights reserved.
This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
CD-1330
P.O.Box 1, Hamamatsu, Japan
animate '08.11
CD-1330
TO SERVICE PERSONNEL
1. Critical Components Information Components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally installed.
2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits.
• Meter impedance should be equivalent to 1500 ohms shunted by 0.15 μF.
WALL
OUTLET
• Leakage current must not exceed 0.5mA.
• Be sure to test for leakage with the AC plug in both polari­ties.
EQUIPMENT
UNDER TEST
INSULATING
TABLE
AC LEAKAGE
TESTER OR
EQUIVALENT
WARNING: CHEMICAL CONTENT NOTICE!
This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.
About lead free solder /
無鉛ハンダについて
All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder.
Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work.
• Sn + Ag + Cu (tin + silver + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)
Caution:
As the melting point temperature of the lead free solder is about 30°C to 40°C (50°F to 70°F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder.
本機に搭載されているすべての基板およびハンダ付けに よる接合部は無鉛ハンダでハンダ付けされています。
無鉛ハンダにはいくつかの種類がありますが、修理時に は下記のような無鉛ハンダの使用を推奨します。
󱾁 Sn+Ag+Cu(錫+銀+銅) 󱾁 Sn+Cu(錫 + 銅) 󱾁 Sn+Zn+Bi(錫 + 亜鉛 + ビスマス)
注意:
無鉛ハンダの融点温度は通常の鉛入りハンダに比べ 30 〜 40℃程度高くなっていますので、それぞれのハンダに合っ たハンダごてをご使用ください。
CD-1330
2
CD-1330
WARNING: Laser Safety
This product contains a laser beam component. This component may emit invisible, as well as visible radi­ation, which may cause eye damage. To protect your eyes and skin from laser radiation, the following pre­cautions must be used during servicing of the unit.
1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm/1 feet away from the laser pick-up unit at all times. Do not stare at the laser beam at any time.
2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.
3) CAUTION: Use of controls, adjustments or perform­ance of procedures other than those specified herein may result in hazardous radiation exposure.
Laser Emitting conditions:
1) When the Top Cover is removed, and the STANDBY/ ON SW is turned to the “ON” position, the laser com­ponent will emit a beam for several seconds to de­tect if a disc is present. During this time (5-10 sec.) the laser may radiate through the lens of the laser pick-up unit. Do not attempt any servicing during this period!
If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be ex­posed to any laser emissions.
2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this manual. Adjustment of this control can increase the laser emission level from the device.
警告:レーザーの安全対策
本機はレーザー光線を放射する部品を搭載しています。 この部品が放射するレーザー光線は目に損傷を起こしま す。このレーザー光線から目及び肌を保護するために、 本機の修理作業中は下記の注意を厳守してください。
1) テスト時または修理時、目及び肌を光ピックアップか
ら 30cm 以上離してください。いかなる場合もレー ザー光線を見つめないでください。
2) 光ピックアップの再調整及び分解はしないでくださ
い。
3) このマニュアル上で指定されている以外の制御、調整、
手順はレーザー光線を照射される結果を招く恐れがあ ります。
レーザー放射条件
1) トップカバーを取り外し STANDBY/ON スイッチを ON
にすると、ディスク検知のため5〜10秒間、光ピッ クアップからレーザー光線が放射されます。この間、 修理はしないでください。
ディスクが検知されなければ、レーザー光線の放射は 停止します。ディスクがセットされている場合、ディ スクで遮られるのでレーザー光線は修理担当者に届き ません。
2) レーザーパワーレベルは光ピックアップ基板上の VR
により調整可能ですが、工場出荷前に調整セット済み なので、この VRは廻さないでください。この VRを廻 すと装置からのレーザー光線の放射レベルが上がる恐 れがあります。
Laser Diode Properties
Material: GaAlAs
Wavelength: 795 nm
Emission Duration: continuous
Laser Output: max. 160 μW *
* This output is the value measured
at a distance of about 200 mm from the objective lens surface on the Optical Pick-up Block.
レーザー
レーザータイプ:GaAlAs 波長: 795nm レーザー出力: 最大 160 μ W
CD-1330
3
CD-1330
T model
U, K, A, G models
L model
Warning for power supply
The primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off !
This primary area is not shielded so it is possible to accidentally touch copper tracks and/or components when servicing the player. Service personnel have to take precautions to prevent touching this area or components in this area.
Note: The screws on the DVD mechanism may never be touched, removed or re-adjusted. Handle the DVD mechanism with care when the unit has to be exchanged! The DVD mechanism is very sensitive for dropping or giving shocks.
CD-1330
4
CD-1330
PREVENTION OF ELECTROSTATIC DISCHARGE
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protect­ed)” can generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as brushing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
Grounding for electrostatic breakdown prevention
1. Human body grounding. Use the antistatic wrist strap to discharge the static electricity from your body.
2. Work table grounding. Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.
Caution:
The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch the optical pickup.
Anti-static wrist strap
1M-ohms
Conductive material (sheet) or steel sheet
CD-1330
5
CD-1330
SYSTEM COMPOSITION /
The MCS-1330 consists of the R-1330, CD-1330 and NS-BP400.
システム構成
MCS-1330は、R-1330、CD-1330および NS-BP400 で 構成されています。
MCS-1330
NS-BP400 NS-BP400
R-1330
CD-1330
FRONT PANEL
CD-1330 (U, T, K, A, G, L, J models)
CD-1330
6
REAR PANELS
CD-1330 (U model)
CD-1330
Bottom view
CD-1330 (T model)
CD-1330 (K model)
CD-1330
7
CD-1330
CD-1330 (A model)
CD-1330 (G model)
CD-1330 (L model)
CD-1330 (J model)
Bottom view
CD-1330
8
CD-1330
SPECIFICATIONS /
Player Section /
Playback System /
......................................................................... CD, CD-R/RW
Audio Section /
Output Level /
................................................................................. 2 ±0.3 V
Signal to Noise Ratio /
......................................................................105 dB or more
Dynamic Range /
......................................................................100 dB or more
Harmonic Distortion / 歪率 (1 kHz)
......................................................................0.003 % or less
Frequency Response /
...................................................................... 2 Hz to 20 kHz
Other Output Equipment /
.......................................................... System control-terminal
General /
Power Consumption /
U, T, K, A, G, L models ................................................ 15 W
J model .......................................................................... 10 W
Power Supply /
U model ........................................................... AC 120 V, 60 Hz
T model ............................................................ AC 220 V, 50 Hz
K model ............................................................ AC 220 V, 60 Hz
A model ............................................................ AC 240 V, 50 Hz
G model ........................................................... AC 230 V, 50 Hz
L model .........................................AC 220/230-240 V, 50/60 Hz
J model ....................................................... AC 100 V, 50/60 Hz
プレーヤー部
再生システム
オーディオ部
出力レベル
ダイナミックレンジ
総合
電源電圧
(1 kHz, 0 dB)
信号対雑音比
周波数特性
その他の出力端子
消費電力
参考仕様
Dimensions (W x H x D) /
...................300 x 67 x 300 mm (11-3/4" x 2-5/8" x 11-3/4")
Weight / 質量
...............................................................3.8 kg (8 lbs. 5 oz.)
Finish /
Black color ................................. U, T, K, A, G, L, J models
Silver color ................................. U, T, K, A, G, L, J models
Accessories /
Audio pin cable (1.0 m) .................................................. x 1
Mini pin cable (0.6 m) .................................................... x 1
* Specifications are subject to change without notice due to product
improvements.
※ 参考仕様および外観は予告なく変更されることがあります。
U ............................. U.S.A. model
T..........................Chinese model
K ...........................Korean model
A ......................Australian model
MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson Multimedia.
“iPod” is a trademark of Apple Inc., registered in the U.S. and other countries.
iPodは、米国およびその他の国々で登録された AppleInc.の商標または登 録商標です。
仕上げ
付属品
寸法(幅 × 高さ × 奥行き)
G ...................... European model
L...................... Singapore model
J ........................Japanese model
DIMENSIONS /
寸法図
255 (10-1/16")
300 (11-13/16")
235 (9-1/4")
67 (2-5/8") 300 (11-13/16")
CD-1330
Unit: mm (inch)
単位:mm(インチ)
9
CD-1330
INTERNAL VIEW
Top view
4512 3
67 8
Front view
9
1
OPERATION (5) P.C.B.
2
OPERATION (7) P.C.B. (L model)
3
DIGITAL (2) P.C.B.
4
DIGITAL (1) P.C.B.
5
OPERATION (3) P.C.B.
6
OPERATION (4) P.C.B.
7
Loader Mechanism Ass’y
8
OPERATION (9) P.C.B.
9
OPERATION (1) P.C.B
10
OPERATION (6) P.C.B
11
OPERATION (8) P.C.B.
10 11
CD-1330
10
CD-1330
DISASSEMBLY PROCEDURES /
(Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet.
1. Removal of Top Cover
a. Remove 4 screws (➀) and 2 screws (➁). (Fig. 1) b. Remove the top cover. (Fig. 1)
Top cover
トップ カ バ ー
1
OPERATION (6) P.C.B.
OPERATION (8) P.C.B.
Front panel ass'y
フロントパネルASSY
3
CB205
CB162
分解手順
(番号順に部品を取り外してください。)
AC 電源コンセントから、電源コードを抜いてください。
1. トップカバーの外し方
a. ①のネジ 4 本、②のネジ 2 本を外します。(Fig.1) b. トップカバーを取り外します。(Fig.1)
2
1
Plate side (R)
プレートサイド(R)
リッド
Flatblade screwdriver
マイナスドライバー
Lid
5
Hook
フック
4
CB152
OPERATION (9)
P. C . B .
Lid
リッド
Plate side (L)
プレートサイド(L)
Hook
フック
5
3
Fig. 1
2. Removal of Front Panel Ass’y
a. Open the disc tray, remove the lid and close the disc
tray. (Fig. 1)
b. Remove 2 screws (
(L and R). (Fig. 1)
c. Remove 2 screws ( d. Remove CB152, CB162 and CB205. (Fig. 1) e. Release 2 hooks and then remove the front panel
ass’y. (Fig. 1)
) and then remove the plate side
) and 2 screws (➄). (Fig. 1)
2. フロントパネル ASSY の外し方
a. ディスクトレイを開けてリッドを取り外し、ディスク
トレイを閉じます。(Fig.1)
b. ③のネジ 2 本を外し、プレートサイド(L、R)を取り
外します。(Fig.1) c. ④のネジ2 本、⑤のネジ 2本を外します。(Fig.1) d. CB152、CB162、CB205 を外します。(Fig.1) e. フック 2 箇所を外し、フロントパネル ASSY を取り外
します。(Fig.1)
CD-1330
11
CD-1330
3. Removal of OPERATION (3) P.C.B.
a. Remove 4 screws (➅) and 2 screws (➆). (Fig. 2) b. Remove CB1. (Fig. 2) c. Pull up the OPERATION (3) P.C.B.. (Fig. 2) d. Remove CB301. (Fig. 2)
4. Removal of Loader Mechanism Unit
a. Remove 4 screws (➇). (Fig. 2) b. Remove CB602 and CB603. (Fig. 2) c. Remove CB601 and ground the terminal face of the
flexible flat cable with a clip or the like. (Fig. 2)
d. Remove the loader mechanism unit. (Fig. 2)
78
2. OPERATION(3)P.C.B. の外し方
a. ⑥のネジ 4 本、⑦のネジ 2本を外します。(Fig.2) b. CB1 を外します。(Fig.2) c. OPERATION(3)P.C.B.を持ち上げます。(Fig.2) d. CB301 を外します。(Fig.2)
4.ローダーメカユニットの外し方
a. ⑧のネジ 4 本を外します。(Fig.2) b. CB602、CB603 を外します。(Fig.2) c. CB601 を外し、カード電線の端子面をクリップ等で
アースします。(Fig.2)
d. ローダーメカユニットを取り外します。(Fig.2)
OPERATION (3) P.C.B.
6
6
CB1
Loader mechanism unit
ローダーメカユニット
17 mm (0.67")
Terminal side
端子面
Clip
クリップ
8
7
CB602 CB603
DIGITAL (1) P.C.B.
CB601
CB301
CD-1330
Use a clip or the like to ground the unit.
クリップ 等 で アースし てくだ さ い 。
Fig. 2
12
CD-1330
When checking the P.C.B.s:
• Spread the rubber sheet and the cloth. Then place the sub chassis unit on the cloth and check it. (Fig. 3)
• Reconnect all cables (connectors) that have been disconnected.
• When connecting the flexible flat cable, be careful with polarity.
• Connect the ground points of the front panel ass’y and OPERATION (3) P.C.B. to the chassis with a ground lead or the like. (Fig. 3)
P.C.B.をチェックする場合には:
・ ゴムシートと布を敷き、その上にサブシャーシユニッ
トを置いてチェックします。(Fig.3) ・ 外したケーブル(コネクター)をすべて接続します。 ・ フラットケーブルを接続する際、極性に注意してく
ださい。 ・ フロントパネル ASSY と OPERATION(3)P.C.B. のアー
スをアース線等でシャーシに接続してください。
(Fig.3)
Ground lead
アース線
Ground lead
アース線
Rubber sheet and cloth
ゴ ム シ ートと布
Front panel ass'y
フロントパネルASSY
OPERATION (3) P.C.B.
Ground lead
アース線
Chassis
シャーシ
Fig. 3
CD-1330
13
CD-1330
TEST MODE /
Check the FL display and indicators for display/indication condition.
テストモード
Check the FL display and Indicators
1. While pressing those 3 keys of this unit as indicated in the figure below, press the “ON/STANDBY, OFF” switch to turn on the power and keep pressing those 3 keys.
"USB" indicator"POWER" indicator
FL ディスプレイとインジケーターの表示状態をチェック します。
● FL ディスプレイとインジケーターの確認
1. 本機 の下 図に 示す 3 つ の キーを押し ながら “O N/ STANDBY、OFF” スイッチを押して電源を入れ、3 つ のキーを押し続けます。
FL display
"ON/STANDBY, OFF" switch
2. With these 3 keys pressed continuously, check that all indicators (POWER, USB) are lit. At the same time, check that all segments of the FL dis­play are lit.
3. Release these 3 keys. Then check that all indica­tors (POWER, USB) as well as all segments of the FL display are turned off.
4. The Test Mode is activated.
While pressing these keys, press the “ON/STANDBY, OFF” switch to turn on the power.
これらのキーを押しながら、“ON/STANDBY、OFF” スイッチを押して電源を入れます。
FL display /
Release the key
キーを離す
FL ディスプレイ表示
All segments ON
全セグメント点灯
All segments OFF
全セグメント消灯
2. 3 つのキーを押したまま、全てのインジケーター (POWER、USB)が点灯していることを確認します。
同時に、FL ディスプレイの全セグメントが点灯し ていることを確認します。
3. 3 つのキーを離します。
全てのインジケーター(POWER、USB)と、FL ディ スプレイの全セグメントが消灯していることを確 認します。
4. テストモードが起動します。
CD-1330
14
CD-1330
Operation Procedure of Test Mode
Function list of panel keys /
Panel key /
OPEN/CLOSE Disc tray open/close /
PLAY/PAUSE
STOP Trace off /
SKIP+/SEARCH+ Trace on /
SKIP-/SEARCH-
パネルキー
Function list of remote control keys /
Key /
キー
CD/USB
PURE DIRECT
OPEN/CLOSE Disc tray open/close /
DIMMER
DISPLAY Firmware version is displayed. /
1 Laser on /
2 Focus on /
3 TE measure /
4
5 Traverce stop /
6
7
8 Spindle off /
9
0–
ENTER
CLEAR
PROGRAM
REPEART
RANDOM
SEARCH -
A-B REPEAT
SEARCH +
PAUSE
SKIP -
PLAY Trace on /
SKIP + Trace on /
STOP Trace off /
テストモード時のパネルキー
ディスクトレイ オープン/クローズ
トレースオフ
トレースオン
テストモード時のリモコンキー
ディスクトレイ オープンクローズ
レーザーオン
フォーカスオン
TE 測定
Traverce in /
トラバースイン
トラバースストップ
Traverce out /
トラバースアウト
Spindle reverce /
スピンドルリバース
スピンドルオフ
Spindle on /
スピンドルオン
トレース オン トレース オン
トレース オフ
* Press “5” key to stop traverce. /
* Press “5” key to stop traverce. /
* Press “8” key to stop spindle. /
* Press “8” key to stop spindle. /
Function /
Function /
ファームウェアバージョン表示
“5”
キーを押してトラバースを停止してください。
“5”
キーを押してトラバースを停止してください。
“8”
キーを押してスピンドルを停止してください。
“8”
キーを押してスピンドルを停止してください。
● テストモード時の操作
機能
機能
Display /
OPEN / CLOSE
TRACE off
TRACE on
Display /
OPEN / CLOSE
Yxxx xxxx
LASER on
FOCUS on
TE measure
TRV in
TRV stop
TRV out
SPDL rev
SPDL stop
SPDL on
TRACE on
TRACE on
TRACE off
表示
表示
Canceling Test Mode
Press the “ON/STANDBY, OFF” switch of this unit to turn off the power.
● テストモードの解除
本機の “ON/STANDBY、OFF” スイッチを押して電源を 切ります。
CD-1330
15
CD-1330
UPDATING FIRMWARE /
After replacing the following parts update the latest firm­ware according to the following procedure.
DIGITAL P.C.B. Microprocessor (IC304) of DIGITAL P.C.B.
ファームウェアの書き込み
Required tools
• Program downloader programs ....... FlashSta.exe
• Firmware .............................................. CD1330.S
CD1330.id
• RS232C cross cable “D-sub 9 pin female”
(Specifications)
Pin No.2 RxD Pin No.2 RxD
Pin No.3 TxD Pin No.3 TxD
Pin No.5 GND Pin No.5 GND
Pin No.7 RTS Pin No.7 RTS
Pin No.8 CTS Pin No.8 CTS
• RS232C conversion adaptor (Part No.: AAX88050)
Preparation and precautions before starting
the operation
• Download firmware downloader program and
firmware from the specified source to the same folder of the PC.
• Prepare the above specified RS232C cross cable.
• While writing, keep the other application software
on the PC closed. It is also recommended to keep the software on the task tray closed as well.
下記の部品を交換した場合、下記の手順により最新の ファームウェアの書き込みを行ってください。
DIGITALP.C.B. DIGITALP.C.B. のマイコン(IC304)
● 必要なツール
・ プログラム書き込み用プログラム....... FlashSta.exe
・ ファームウェア.....................................................CD1330.S
CD1330.id
・ RS232C クロスケーブル “D-sub9pin メス”
(仕様)
PinNo.2RxD PinNo.2RxD PinNo.3TxD PinNo.3TxD
PinNo.5GND PinNo.5GND
PinNo.7RTS PinNo.7RTS
PinNo.8CTS PinNo.8CTS
・ RS232C変換アダプター(部品番号:AAX88050)
● 操作前の準備と注意
・ PC へ指定のダウンロード先からファームウェア
書き込み用プログラムおよび、ファームウェアを 同じフォルダにダウンロードしてください。
・ RS232C クロスケーブルは必ず上記仕様のものを
用意してください。
・ 書き込み時は、PC 上の他のアプリケーションソ
フトは閉じてください。 さらに、タスクトレイ上にあるソフトも閉じてお くことを推奨します。
CD-1330
16
Loading...
+ 37 hidden pages