Yale YRL236 Installation And Programming Instructions

Download

Page 1

Yale Assure Lever Key Free Push Button Installation and Programming Instructions

™

(YRL236)

#8-32 x 5/16"

#7 wood & #8-32 machine x 20mm

Combination screws

Machine screws

M4 x 22mm

Pan head machine

screws

Before you begin

DOWNLOAD

THE BILT APP

for step-by-step installation

instructions & to register

your product

Template

Levers

Optional Smart Module*

*Yale Smart Module is not included with YRL236-NR models.

Battery Cover

Key Free

Cylinder

Strike Plate

AA Alkaline

Batteries

Key

Latch

Battery Cover

Interior Lock

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO

THE PRODUCT AND VOID THE FACTORY WARRANTY

P/N YRL-LKFPBINSTL-FUL Rev A

Interior Mounting Plate

Page 2

Preparing to Install

Tools Needed

Standard

Phillips Head

Screwdriver

Tools necessary only for new doors or adjusting existing prep.

Drill

Utility Knife

Pencil

Wood Mortise

Chisel

Template

Tape

Measure

Level

P/N YRL-LKFPBINSTL-FUL Rev A

Page 3

Checking Measurements

2-3/8" or 2-3/4"

(60mm or 70mm)

Backset

2-1/8" (54mm)

Diameter

1-3/8" or 1-3/4"

(35mm or 44.5mm)

Door Thickness

1" (25mm)

Diameter

P/N YRL-LKFPBINSTL-FUL Rev A

Page 4

Determining Door Handing

Inswinging Door

Interior

Left Hand Right Hand

Exterior

Face a door swinging open

away from you.

If it swings open to the right,

it is a right hand door. If it

swings open to the left, it is a

left hand door.

Latchbolt Curve

Outswinging Door

Left Hand

Reverse

Face a door swinging open

If it swings open to the right, it

is a right hand reverse door. If it

swings opens to the left, it is a

left hand reverse door.

Interior

Exterior

toward you.

Right Hand

Reverse

Curve of latchbolt must contact strike plate first.

Optional

Smart Module

Frame

Inside of Door

Door Strike Plate

Exterior

Outside of Door

P/N YRL-LKFPBINSTL-FUL Rev A

Page 5

Preparing Door & Frame

Necessary for new doors or adjusting existing prep.

2-1/8"

(54mm)

Dia.

2-3/8" (60mm)

(25mm)

Dia.

2-3/4" (70mm)

Backset

Frame

Inside

of Door

Drill holes 1/2 way

through door then

complete from other side

to prevent splitting.

Frame

1" (25mm) Deep

P/N YRL-LKFPBINSTL-FUL Rev A

Page 6

Installing Latch & Strike Plate

Right Hand Installation Shown

2-3/8" through bolt posts

default

PULL

2-3/4" through bolt posts

optional

Outside of Door

*2-3/8" (60mm) or 2-3/4" (70mm)

Note: Adjustment based on backset

*Backset

Frame

P/N YRL-LKFPBINSTL-FUL Rev A

Page 7

Installing Push Button

Right Hand Installation Shown

“TOP” mark must be

on top surface and tailpiece

in vertical position.

Incorrect orientation will

cause lock to fail.

Inside of

Right Hand Door

Outside of

Right Hand Door

P/N YRL-LKFPBINSTL-FUL Rev A

Page 8

Installing Interior Mounting Plate

Right Hand Installation Shown

Inside of

Right Hand Door

Inside of Right Hand Door

P/N YRL-LKFPBINSTL-FUL Rev A

Page 9

Attaching the Cable Assembly

Right Hand Installation Shown

Inside of

Right Hand Door

Use cable hooks for

proper cable

routing.

Ensure cable is securely fastened into adapter.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 10

Installing Interior Lock

Right Hand Installation Shown

Inside of

Right Hand

Door

“Click”

P/N YRL-LKFPBINSTL-FUL Rev A

Page 11

Installing Exterior Key Free Cylinder

Outside of Right Hand Door

Latch

Bar

Key free cylinder must be installed

with bar away from latch.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 12

Installing Exterior Lever

Press pin while installing

lever so lock is not damaged.

Outside of Right Hand Door

P/N YRL-LKFPBINSTL-FUL Rev A

Page 13

Installing Interior Lever

Inside of Right Hand Door

Press pin while installing

lever so lock is not damaged.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 14

Testing Mechanical Operation

Test interior and exterior operation with door open.

Outside of Right Hand Door

Test thumbturn and both levers in locked and unlocked positions. If operation fails, check installation beginning with Step 3 and refer to

Hardware Troubleshooting.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 15

Installing Optional Smart Module

(if included)

Inside of Right Hand Door

Batteries must not be

installed prior to inserting

and/or removing module.

NOTE: If a Smart module was included with your lock, it is in a separate box with additional module installation instructions.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 16

Installing Batteries & Cover

Inside of Right Hand Door

Congratulations, you've installed the

Yale Assure Lever Key Free Push Button ( )!YRL236

Programming Instructions will help

you customize your product.

™

P/N YRL-LKFPBINSTL-FUL Rev A

Page 17

Testing Push Button Operation

Test with door open.

A Master Enty Code must be created upon installation or after resetting the lock to factory default. Programming and use of lock is not possible until this step has been successfully completed. See of Programming Instructions below.

Enter Entry Code

Press

If push button operation test fails, check installation beginning with Step 2.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 18

Reset Button

Interior Lock

When resetting the lock, all user codes, including the Master Entry Code*, are deleted. All programming features are reset to original default settings. See “Factory Settings”.

1. Remove the battery cover and batteries.

2. Remove the interior lock to access the reset button.

3. The reset button (see image above) is marked.

4. Re-insert 3 batteries and hold the reset button for 3 seconds.

5. While still holding the reset button, insert the 4th battery, and hold the reset button for an additional 3 seconds.

6. Release the reset button.

7. Re-install the interior lock onto the door.

*Upon reset, Master Entry Code creation is the only option available and must be performed prior to any other programming of the lock.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 19

Settings

Factory Setting

Master Entry (PIN) Code

Audio Mode

Automatic Re-lock

Automatic Re-lock Time

Inside Indicator Light

Lockout Mode

One Touch Locking

Registration required*

Enabled

Disabled

30 Seconds

Disabled (Off)

Disabled

Enabled

Shutdown Time 60 Seconds

Wrong Code Entry Limit

5 Times

*The Master Entry Code must be created prior to any other programming of the lock.

NOTE TO INSTALLER AND CONSUMER

While Yale has included several features to prevent lockout

(9-Volt battery jumper, low battery warnings), it is still possible for a lockout situation to occur. Because this product does not have a mechanical override (a key), Yale recommends to use

this product in an environment where there are additional entry points into the dwelling.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 20

Cycle lock in both the locked and unlocked positions. If problems are found:

Tailpiece and spindle will not mate and ﬁt into the interior escutcheon

a. Ensure that your door is between 1-3/8" and 1-3/4" thick b. Ensure that the square shaped spindle has “Top” writing and arrow facing upwards c. Place the tailpiece in the vertical position d. Verify that the thumb turn is in the horizontal (unlocked) position

Thumbturn does not rotate electronically or physically

a. Verify that inside of the lock is properly seated on the mounting bracket b. Ensure that the square shaped spindle has “Top” writing and arrow facing upwards c. Place the tailpiece in the vertical position d. Verify that the thumb turn is in the horizontal (unlocked) position

I'm getting an alert when I try to lock or unlock the door electronically

a. Do not turn or depress the lever during operation, this could cause a jam alarm b. Check that thumb turn does not have anything preventing it from physically rotating c. Verify that you can rotate thumb turn freely

My lock is not making any sound when I push buttons

a. Using the programming tree in the manual to verify that Audio is enabled b. If Audio is enabled, ensure that the white cable, that connects the keypad to the interior of the lock, is not pinched or broken

When rotating the thumbturn I hear noise

a. A little bit of noise is normal when operating the thumbturn b. If cranking, grinding or clicking occurs please verify your installation

The locking pins will not retract when I try to install the levers

a. If the thumb turn is in vertical (locked) position, rotate the thumb turn the horizontal (unlocked) position and it will retract

P/N YRL-LKFPBINSTL-FUL Rev A

Page 21

Programming Instructions

Speaker

Master Entry Code must be created before any further programming. Max User Codes = 250 with Smart Module and 25 without.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 22

Creating Master Entry Code

Creating a Master Entry Code must be performed upon installation or after resetting the lock to factory default. Programming and use of lock is not possible until this step has been successfully completed.

Press

Enter 4-8 digit Master Entry Code.

Press

P/N YRL-LKFPBINSTL-FUL Rev A

Page 23

Creating User Entry Codes

Master Entry Code must be created ﬁrst. *Max user codes = 250 with Smart Module and 25 without.

Enter Master Entry Code

Press

Press Press

Adding more User Codes:

Press Enter 4-8 digit Entry Code

Press

Enter 4-8 digit Entry Code Press

(code ﬂashes)

To end programming:

Press

P/N YRL-LKFPBINSTL-FUL Rev A

Page 24

Unlocking Door with Entry Code

Enter Entry Code

Press

Code Chart

Master:

User Name:

Duplicate if necessary

Entry Code Management

Entry Code

P/N YRL-LKFPBINSTL-FUL Rev A

Page 25

All Code Lockout Mode: This feature is enabled by the Master code. When enabled, it restricts all user (except Master) entry code access. When attempting to enter a code while the unit is in Lockout, unit ﬂashes and sounds a Lockout alarm.

Audio Mode: The audio setting for entry code veriﬁcation is set to Enable (1) by default; otherwise it can be set to Disable (3) for quiet areas.

Automatic Re-lock Time: After a successful code entry or manual unlock, the lock will automatically re-lock after each unlock in an effort to keep your home secure. This feature is optional, and can be turned off. In the ON mode, the lock will automatically re-lock after thirty (30) seconds.

Inside Indicator Light: Located on the interior escutcheon. Shows active status (Locked) of lock and can be enabled or disabled in the Advanced Lock Settings (Main Menu selection #3).

Low Battery: When battery power is low, the Yale logo button lights RED when unit is used. If battery power is completely lost, use the 9Volt battery override. To use the 9V battery override apply 9V battery, in either direction, to terminals below the keypad for backup power option. Enter your entry code to unlock the door.

Master Entry Code: The Master Entry Code is used for programming and for feature settings. It must be created prior to programming the lock. The Master code will also operate (unlock/lock) the lock.

Smart Module Setting: With the optional Smart Module installed, this setting becomes available thru the Main Menu (7) and allows

the lock to connect with a network controller.

One Touch Locking: When the latch is retracted, activating the keypad will extend the latch (during Automatic Re-lock duration or when Automatic Re-lock is disabled). When One-Touch Re-lock is not in use (disabled), any valid entry code will re-lock the lock.

Shutdown Time: The unit will shutdown (ﬂashing RED) for sixty (60) seconds and not allow operation after the wrong code entry limit (5 attempts) has been met.

Tamper Alert: Audible alarm sounds if attempting to forcibly remove outside lock from door.

User Entry Code: The User code operates the lock. Maximum number of user codes is 250 with Smart Module and 25 without. Note:

When deleting User Entry Code(s), screen will display User Number (not entry code) being deleted.

Wrong Code Entry Limit: After ﬁve (5) unsuccessful attempts at entering a valid entry code, the unit will shut down and not allow operation for sixty (60) seconds.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 26

Feature Programming Through Menu Mode Using Master Entry Code*

1. Enter 4-8 digit Master Entry Code* followed by key.

2. Enter digit corresponding to the function to be performed followed by the key.

*The Master Entry Code must be created prior to any other programming of the lock.

Master PIN Code Setting

User PIN Code Registration

Advanced Lock Settings

Delete

Automatic Re-lock

Inside Indicator Light

Continue

Complete

Continue

Complete

Continue

Complete

Disable

30 sec

60 sec

2 min

3 min

Continue

Enable

Disable

Audio Mode

All Code Lockout Mode

**Network Module Setting

One Touch Locking

Enable

Disable

Enable

Disable

Join the Network

Exit the Network

P/N YRL-LKFPBINSTL-FUL Rev A

Enable

Disable

Complete

Default settings in bold.

**This function appears only with network module installed.

Page 27

Symptom

Suggested Action

* When batteries are replaced, Smart Module locks have a real time clock that will be set

through the User Interface (UI); it is recommended to verify correct date and time

particularly those locks operating under Daylight Saving Time (DST).

P/N YRL-LKFPBINSTL-FUL Rev A

Page 28

FCC:

Class B Equipment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Ÿ Reorient or relocate the receiving antenna. Ÿ Increase the separation between the equipment and receiver. Ÿ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Ÿ Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modiﬁcations to this device, not expressly approved by ASSA ABLOY Residential Group, Inc. could void the user's authority to operate the equipment.

Industry Canada:

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement.

Product Support Tel 1-855-213-5841 • www.yalehome.com

Yale® and Yale Real Living® are registered trademarks of ASSA ABLOY Residential Group, Inc.

Assure Lever™ is a trademark of ASSA ABLOY Residential Group, Inc.

Other products' brand names may be trademarks or registered trademarks of their respective

owners and are mentioned for reference purposes only.

permission of ASSA ABLOY Residential Group, Inc. is prohibited.

P/N YRL-LKFPBINSTL-FUL Rev A

Page 29

®®

Yale Z Plus Module

-Wave

Installation and Programming Instructions

Installing the Z Plus Module-Wave

IMPORTANT: the batteries be removed priormust to removing and/or inserting the network module:

• Remove battery cover and batteries.

• Remove and/or insert Network Module.

• Reinstall batteries and battery cover.

Enrolling/Unenrolling the Network Module:

This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products. This device must be used in conjunction with a Security Enabled Z-Wave Controller in order to fully utilize all implemented functions. This product can be operated in any Z-Wave network with other Z-Wave certiﬁed devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

To Enroll/Add the Module (Inclusion Mode):

• Enter the 4-8 digit Master code followed by the key.PIN

• Press the key followed by the key.

To Unenroll/Remove the Module (Exclusion Mode):

• Enter the 4-8 digit Master code followed by the key.PIN

• Press the key followed by the key.

Factory Reset - If No Controller:

• See the Lock Installation Manual

• Please use this procedure only when the network primary controller is missing or otherwise inoperable.

For System Integrators: Speciﬁc Z-Wave Plus association and parameter information for your lock is available at YaleHome.com/ZwavePlus.

P/N 202- - - Rev DAYR ZW INSTAL FUL

Page 30

Warning: Changes or modiﬁcations to this device, not expressly approved by Yale Security Inc. could void the user's authority to operate the equipment.

FCC:

Contain : U4A- 0FCC ID YRHCPZW FM Model: 2-YRMZW US This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Rules. These limits are designed to provideFCC reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and

receiver.

 Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV

technician for help.

and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. En vertu des règlements d'Industrie Canada, cet émetteur radio ne peut fonctionner avec une antenne d'un type et un maximum (ou moins) approuvés pour gagner de l'émetteur par Industrie Canada. Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente ( ) ne dépasse pas ce qui estPIRE nécessaire pour une communication réussie.

Section 7.1.3 of -RSS GEN This Device complies with Industry Canada License-exempt standard(s).RSS Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada RSS standard exemptes de licence(s). Son fonctionnement est soumis aux deux conditions suivantes: 1) ce dispositif ne peut causer des interférences, et 2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.

THIS DEVICE COMPLIES WITH PART OF THE FCC RULES15 . OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND THIS DEVICE MUST ACCEPT ANY, (2) INTERFERENCE RECEIVED INCLUDING INTERFERENCE, THAT MAY CAUSE UNDESIRED OPERATION.

Industry Canada: Contain : 6982A- 0IC YRHCPZW FM Model: 2-YRMZW US Section 7.1.2 of -RSS GEN Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type

Product Support Tel 1-855-213-5841 • www.yalehome.com

Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.

Yale® and Yale Real Living® are registered trademarks of Yale Security Inc., an ASSA ABLOY Group Company.

Other products’ brand names may be trademarks or registered trademarks of their respective owners and are mentioned for

This radio transmitter 6982A- 0 has beenYRHCPZW FM approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Le présent émetteur radio 6982A- 0 a étéYRHCPZW FM approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

CAN ICES NMB-3B/ -3B

YALE, with its unique global reach and range of products, is the world's favorite lock

– the preferred solution for securing your home, family and personal belongings.

ASSA ABLOY is the global leader in door opening solutions,

dedicated to satisfying end-user needs for security, safety and convenience.

Page 31

®®

Yale ZigBee Module

Installation and Programming Instructions

Installing the ZigBee Module

IMPORTANT: the batteries be removed priormust to removing and/or inserting the network module:

• Remove battery cover.

• Remove batteries.

• Remove and/or insert network module.

• Reinstall batteries.

• Replace cover.

Enrolling/Unenrolling the Network Module:

This device is a security enabled ZigBee product that is able to use encrypted ZigBee messages to communicate to other security enabled ZigBee products. This device must be used in conjunction with a Security Enabled ZigBee Controller in order to fully utilize all implemented functions. This product can be operated in any ZigBee network with other ZigBee certiﬁed devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

To Enroll the Module (Inclusion Mode):

• Enter the 4-8 digit Master code followed by the key.PIN

• Press the key followed by the key.

To Unenroll the Module (Exclusion Mode):

• Enter the 4-8 digit Master code followed by the key.PIN

• Press the key followed by the key.

P/N 202- - - Rev CAYR ZB INSTAL FUL

Page 32

FCC:

FCC ID YRHCPZB FM: U4A- 0 Model: 2YRMZB This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Rules. These limits are designed to provideFCC reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and

receiver.

 Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

 CTVonsult the dealer or an experienced radio/

technician for help.

This equipment complies with radiation exposureFCC limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada: IC YRHCPZB FM: 6982A- 0 Model: 2YRMZB This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and

2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux d'IndustrieCNR Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.

Important Note: Radiation Exposure Statement:

This equipment complies with radiation exposure limitsIC set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Note Importante: (Pour l’utilisation de dispositifs mobiles) Declaration d’exposition aus radiations:

Cet équipement est conforme aux limites d´exposition aux rayonnements établies pour un environnement nonIC contrôlé. Cet équipment doit être installé et utilisé avec un mimimum de 20 cm de distance entre la source de rayonnement et votre corps.

This device complies with Part 15 of the rules.FCC Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modiﬁcations not expressly approved by manufacturer could void the user’s authority to operate the equipment.

IMPORTANT! Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Product Support Tel 1-855-213-5841 • www.yalehome.com

Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.

Yale® and Yale Real Living® are registered trademarks of Yale Security Inc., an ASSA ABLOY Group Company.

Other products’ brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only.

IMPORTANT! Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IMPORTANT! Tous les changements ou modiﬁcations pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de l’utilisateur pour actioner cet équipment.

CAN ICES NMB-3B/ -3B

YALE, with its unique global reach and range of products, is the world's favorite lock

– the preferred solution for securing your home, family and personal belongings.

ASSA ABLOY is the global leader in door opening solutions,

dedicated to satisfying end-user needs for security, safety and convenience.