Yale YRL226, YRL256 Installation Manual
Yale Assure Lever®
Touchscreen (YRL226) and Key-Free Touchscreen (YRL256)
Installation and Programming Instructions
This manual will walk you through all the required steps to add your new
Yale Assure Lever to your door.
• Remove existing door knob or lever
• Double check door measurements
• Install your Assure Lever
• Program your Assure Lever
• Add your Assure Lever to your smart home system or Yale Access
app if purchased with Yale Smart Module or Yale Access Upgrade kit
Tools Needed
Standard
Phillips Head
Screwdriver
Before you begin
DOWNLOAD
THE BILT APP
Tools Needed For New
Doors Or Adjusting Existing Door
Using the app on your smart
phone, scan this QR for step-by
-step installation instructions & to
register your lock
Drill
Utility
Knife
Pencil
Wood
Mortise
Chisel
Tape
Measure
Level
WARNING
This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65warnings.ca.gov.
Failure to follow these instructions could result in damage to the product, voiding the factory warranty and could lead to failure of the product to provide access.
P/N YRL-TS-MNL-0018 Rev B
1
Part of ASSA ABLOY
What's In The Box
Touchscreen
Keypad
Keys (YRL226)
OR
Cylinder
(YRL226)
Battery Cover
Key-Free
Cylinder
(YRL256)
Yale Smart Module
(not included with
NR models)
Let's Get Started
Installation Guide
and Door Template
Levers
Inside Lock
Mounting Hardware
Latch
(AYRL-DRIVE
Strike Plate
Adjustable Drive-In Latch
available for purchase)
AA Alkaline
Batteries
x4
#7 wood & #8-32
Machine x 20mm
Combination Screws
2
P/N YRL-TS-MNL-0018 Rev B
Mounting Plate
x2
#8-32 x 5/16"
Machine Screws
Battery
Cover
Key
x2
M4 x 22mm
Pan Head Machine
Screws
Part of ASSA ABLOY
1
Remove Existing Door Knob or Lever
Do not discard old lock hardware until Assure Lever has been successfully installed.
Frame
3
P/N YRL-TS-MNL-0018 Rev B
Part of ASSA ABLOY
2
Check Door Measurements And
Make Adjustments If Needed
Door Checker
Use door checker from installation guide envelope to verify your door measurements
and make any needed adjustments.
Check
Your Door
Let's Get Started
New Door Marking Template
With the door checker, use the template from installation guide envelope to prep
a new door that has not been predrilled for hardware.
Guide
Let's Get Started
New Door
Marking
Template
Outside of Right Hand Door
YRL226 Cylinder and Key Shown
YRL256 has Key-Free Cylinder (No Key)
4
P/N YRL-TS-MNL-0018 Rev B
Part of ASSA ABLOY
3
x4
Actual Size
Install Latch Strike Plateand
Right Hand Installation Shown
AYRL-DRIVE
Adjustable Drive-In Latch
available for purchase
2-3/8" through bolt posts, default
2-3/4" through bolt posts, optional
O
Note: Adjustment is based on backset
Outside
of Door
2-3/8" (60mm)
or
2-3/4" (70mm)
Backset
PULL
Frame
5
P/N YRL-TS-MNL-0018 Rev B
Part of ASSA ABLOY
4
Install Touchscreen Keypad
Right Hand Installation Shown
“TOP” mark must be
on top surface and tailpiece
in vertical position.
Incorrect orientation will
cause lock to fail.
Door face hole
must be at least
2-1/8".
If hole is too
small, a door lock
installation kit or
jig should be used
to increase hole
size.
Inside of
Right Hand Door
Outside of
Right Hand Door
6
P/N YRL-TS-MNL-0018 Rev B
Part of ASSA ABLOY
5
x2
Actual Size
Install Inside Mounting Plate
Right Hand Installation Shown
Inside of
Right Hand Door
Make sure keypad
and mounting plate
are straight before
tightening screws.
Inside of
Right Hand Door
Insert cable through cable hole
7
P/N YRL-TS-MNL-0018 Rev B
Part of ASSA ABLOY
6
Attach Cable
Right Hand Installation Shown
Inside of
Right Hand Door
Make sure
cable is secure
Use cable
hooks for
proper cable
routing. Do
not pinch
cable.
8
P/N YRL-TS-MNL-0018 Rev B
Part of ASSA ABLOY
7
x2
Actual Size
Install Inside Lock
Right Hand Installation Shown
“Click”
Inside of
Right Hand
Door
9
P/N YRL-TS-MNL-0018 Rev B
Part of ASSA ABLOY
Loading...