Yale YRD220ZW605 Quick Start Guide

™

Yale Real Living
Touchscreen Deadbolt Quickstart Guide

For Technical Assistance call Yale:

1-800-810-WIRE (9473).

For more information go to: www.yalerealliving.com

1

(2) M4 x 25.4mm

[8-32 x 1"]

Flat Head

Combination Screws

2

(2) M4 x 25.4mm
[8-32 x 1"]
Flat Head
Combination Screws

Detail A

Inside Mounting Plate

Components

Quick Start Instructions

Installation Instructions

Door Marker

Outside Escutcheon

Inside Escutcheon Assembly:

• Inside Mounting Plate

• Inside Escutcheon

• Battery Cover

4 AA Alkaline Batteries

Bolt

Strike Plate

Screw Pack (7 screws)

2 Keys

Tools Needed

 Phillips #2 screwdriver
 2-1/8" (54mm) hole saw
 1" (26mm) boring bit
 7/64" (2.5mm) drill bit
 Chisel & hammer

Outside Escutcheon

3

4

Inside Mounting Plate

(2) M6 x 59.5mm

[15/64 x 2-11/32"]

Pan Head Machine Screws

Cable

See Detail B

5

Inside Escutcheon

7

6

(3) M4 x 8mm
[8-32 x 5/16"]

Pan Head Screws

Battery Cover

9

8

10

Harness Clip

Detail B

Directions

1. Install bolt in door.

NOTE: The bolt must be in a retracted position
when installing the lockset.

Attach with two (2) M4 x 25.4mm screws
supplied.

2. Install strike on the door frame.

3. Route the cable through 2-1/8" diameter hole.

NOTE: Cable must go

under bolt and through.

See Detail A.

4. Insert outside escutcheon while routing cable
through inside mounting plate’s 1/2" hole; insert
mounting plate “tongue” into bottom slot of
outside escutcheon and tailpiece through bolt.

5. Secure inside mounting plate to outside
escutcheon using (2) M6 x 59.5mm pan head
machine screws. Do not over-tighten.

6. Attach cable connector to inside escutcheon
circuit board (See Detail B above). Press firmly
with thumbs so that back edge (wires) of
connector lines up with arrows on PCB.

An ASSA ABLOY Group brand

CAUTION:

Use care when assembling to ensure that cable
lies against the back recessed area of the inside
escutcheon.

Position and bend the cable, using the harness
clip as shown in Detail B to prevent binding
when installing the escutcheon over the mounting
plate.

7. Slide inside escutcheon over mounting plate.

8. Install and secure using (3) M4 x 8mm pan
head screws through the battery housing into
the mounting plate.

9. Insert four (4) AA alkaline batteries. The lock
responds, “Welcome to Yale Real Living.”

Note: Refer to programming instructions prior to
completion of step 10.

10. Install battery cover and tighten
screw with #2 Phillips screwdriver.

P/N AYRD220-INST-QUK Rev B

Programming

Yale Real Living

™

Touchscreen Deadbolt Quickstart Guide

Open Door With PIN Code

1. Touch the screen with
the back of your hand
or fingers to activate.

1 2 3 4

M

1. Touch the screen with
the back of your hand
or fingers to activate

.

2. Enter the 4-8 digit Master
PIN code* followed by
the

key.

Lock Response: “Menu

mode, enter number, press
the

key to continue.”

3. Enter digit corresponding
to the function to be
performed followed by
the

key.

Follow the voice
commands.

4. Press the

key to
complete the process
and conclude the
programming session.

Note: If the lock is
connected to a controller,
it is recommended that it
be programmed through the
centralized user interface
(PC or hand-held device)
to ensure communication
between the lock and the
controller unit.

*Default Master Pin Code must be changed
prior to any programming of lock.

Master PIN Setting*

Register User PIN

Auto Relock

Volume

Language

All Code Lock-Out

HCP Module

Setting**

**This function appears only
with network module installed.

M

Register

Delete

Enable

Disable

High

Low

Silent

English

Spanish

French

Enable

Disable

Register

Delete

User Number (UN)

5

 1~25 : without network module
 1~250 : with network module

U

Continue

Complete

Continue

Complete

Features

• For proper security, the Master
PIN code* must be changed
prior to programming the lock.

• PIN codes can be 4 to 8
digits in length.

• The
accept an entry, and also to
conclude a programming
session.

• The
enter or to continue additional
steps in a programming
sequence.

For more information go to: www.yalerealliving.com

key is used to enter or

key is used either to

*The factory default Master
PIN code is: 1 2 3 4 5 6 7 8.

For Technical Assistance call Yale:

1-800-810-WIRE (9473).

2. Enter PIN code.

3. Touch the
key to confirm

the selection.

4. Unlock.

P/N AYRD220-INST-QUK Rev B

An ASSA ABLOY Group brand