Yaesu FT60 User Manual

FT-60R

Technical Supplement

2005 VERTEX STANDARD CO., LTD. EH017M90B

VERTEX STANDARD CO., LTD.

4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan

VERTEX STANDARD

US Headquarters

10900 Walker Street, Cypress, CA 90630, U.S.A.

International Division

8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A.

YAESU EUROPE B.V.

P.O. Box 75525, 1118 ZN Schiphol, The Netherlands

YAESU UK LTD.

Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K.

VERTEX STANDARD HK LTD.

Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong

Introduction

This manual provides the technical information necessary for servicing the FT-60R VHF/UHF Dual Band Transceiver.

Servicing this equipment requires expertise in handing surface-mount chip components. Attempts by non-qualified persons to service this equipment may result in permanent damage not covered by the warranty, and may be illegal in some countries.

Two PCB layout diagrams are provided for each double-sided board in this transceiver. Each side of the board is referred to by the type of the majority of components installed on that side (“Side A” or “Side B”). In most cases one side has only chip components (surface-mount devices), and the other has either a mixture of both chip and leaded components (trimmers, coils, electrolytic capacitors, ICs, etc.), or leaded components only.

While we believe the information in this manual to be correct, VERTEX STANDARD assumes no liability for damage that may occur as a result of typographical or other errors that may be present. Your cooperation in pointing out any inconsistencies in the technical information would be appreciated.

Contents

Specifications ....................................................................................................................................................................2

Exploded View & Miscellaneous Parts .......................................................................................................................4

Block Diagram ..................................................................................................................................................................5

Circuit Description .......................................................................................................................................................... 7

Alignment ..........................................................................................................................................................................9

Board Units (Schematics, Layouts & Parts)

MAIN Unit ................................................................................................................................................................ 13

VR Unit ...................................................................................................................................................................... 47

Specifications

General

Frequency Ranges: RX 108 - 137 MHz (Air Band), (Cellular Blocked) 137 - 520 MHz (AM/FM),

700 - 999.990 MHz (FM)

TX 144-148 MHz, 430-450 MHz

Channel Steps: 5/10/12.5/15/20/25/50/100 kHz Frequency Stability: ±5 ppm @ 14 °F to 140 °F (–10 °C to +60 °C) Repeater Shift: ±600 kHz (144 MHz), ±1.6/5.0/7.6 MHz (430 MHz) Emission Type: F2 (F2D), F3 (F3E) Antenna Impedance: 50 W Supply Voltage: Nominal: 7.2 V DC, Negative Ground

(Negative Ground) Operating: 6.0 ~ 16.0 V DC (EXT DC Jack)

11.0 ~ 16.0 V DC (EXT DC Jack with Charging)

Current Consumption: 125 mA (Receive) (Approx. @7.2 V) 45 mA (144 MHz, Standby, Saver Off)

47 mA (430 MHz, Standby, Saver Off) 19 mA (Standby, Saver On)

0.8 mA (Auto Power Off)

1.5 A (5 W TX, 144 MHz)

1.6 A (5 W TX, 430 MHz)

Operating Temperature: –4 °F to 140 °F (–20 °C to +60 °C) Case Size: 2.3” (W) x 4.3” (H) x 1.2” (D) (58 x 109 x 30 mm) (W/O knob, antenna, and belt clip) Weight: 13.05 Oz (370 g) with FNB-83, and antenna

Transmitter

RF Power Output: 5.0 W (High) / 2.0 W (Middle) / 0.5 W (Low) (Approx.) Modulation Type: Variable Reactance F2 (F2D), F3 (F3E) Maximum Deviation: ±5.0 kHz (F2D, F3E) Spurious Emission: At least 60 dB down (@ High and Middle power)

At least 40 dB down (@ Low power)

Microphone Impedance:2 kW

Receiver

Circuit Type: Double-Conversion Superheterodyne Intermediate Frequencies: 1st: 47.25 MHz, 2nd: 450 kHz Sensitivity : 0.8 µV TYP for 10 dB SN (108-137 MHz, AM)

(Cellular Blocked) 0.2 µV for 12 dB SINAD (137-140 MHz, FM)

0.16 µV for 12 dB SINAD (140-150 MHz, FM)

0.2 µV for 12 dB SINAD (150-174 MHz, FM)

0.3 µV TYP for 12 dB SINAD (174-300 MHz, FM)

0.8 µV for 10 dB SN (300-336 MHz, AM)

0.25 µV for 12 dB SINAD (336-420 MHz, FM)

0.2 µV for 12 dB SINAD (400-470 MHz, FM)

0.25 µV for 12 dB SINAD (470-520 MHz, FM)

0.5 µV TYP for 12 dB SINAD (800-900 MHz, FM)

0.8 µV TYP for 12 dB SINAD (800-999.990 MHz, FM)

Selectivity: 12 kHz/35 kHz (–6 dB /–60 dB) AF Output: 400 mW @ 8 W for 10 % THD (@ 7.5 V)

Specifications are subject to change without notice, and are guaranteed within the 144 and 430 MHz amateur bands only. Frequency ranges will vary according to transceiver version; check with your dealer.

RA0321900 RUBBER CAP

RA0111400 RING NUT (x2 pcs)

RA0210600 RUBBER PACKING (x2 pcs)

RA0209900 KNOB

RA0209800 KNOB

RA0209700 VOLUME KNOB

G6090160 LCD

RA032090B LCD HOLDER

RA0324700 INTER CONNECTOR

RA0324800 REFLECTOR SHEET

RA0107000 TERMINAL PLATE R (x2 pcs)

RA0211200 INTER CONNECTOR

RA0595200 HOLDER

VR-Unit

Exploded View & Miscellaneous Parts

RA0611600 WINDOW

RA0599500 FRONT CASE ASSY (W/ MIC SHEET, PACKING PAD(YER), SP NET,LIGHT GUIDE, DOUBLE FACE(WINDOW))

RA0322000 RUBBER

CP7968001 PANEL ASSY

M4090142B SPEAKER



RA0613500 RUBBER KNOB

RA0110200 HOLDER RUBBER

MAIN-Unit

RA0616500 SPONGE RUBBER

RA0322800 TERMINAL PLATE

RA021080A (Lot. 5-) SPACER RA0210800 (Lot. 1-4) SPACER

RA021020A RUBBER PACKING

RA055770B (Lot. 31-) LATCH NAIL C RA0123500 (Lot. 1-30) LATCH NAIL B

CAUTION

The mic element must be desoldered and removed from the PCB on order to reinstall its protective rubber cover.

Therefore, be careful not to remove this cover unless mic element replacement is necessary.

VXSTD P/N

No.

U9900068



U9900063



U9900051



U02206007



Non-designated parts are available only as part of a designated assembly.



Screw List

Description TAPTITE SCREW M2X4NI#3 TAPTITE SCREW 2X3.3NI TAPTITE SCREW M2X4B#3 SEMS SCREW SM2.6X6B

Qty.

2 2 2









CP7969001 REAR CASE ASSY (W/ SMA CNNECTOR)

RA0618700 PAD (x2 pcs)



RA0318700 BLIND SHEET

CP7970001 BELT CLIP ASSY

Exploded View & Miscellaneous Parts

Note

Block Diagram

Note

Circuit Description

VHF Reception

Incoming VHF signal is passed through the low-pass filter network, antenna switching diode D1066 (HVC131) and D1068 (RLS135), and low-pass filter network to the RF amplifier Q1085 (3SK296ZQ). The amplified RF sig- nal is passed through band-pass filtered again by varactor-tuned resonators L1060, L1061 and L1062, and D1063, D1064, and D1065 (all HVC365), then applied to the 1st mixer Q1083 (3SK296ZQ) along with the first local signal from the PLL circuit.

The first local signal is generated between 191.25 MHz and 195.25 MHz by the VHF VCO, which consists of Q1067 (2SC5006), switching diodes D1034, D1035 (both

HSC277), and varactor diodes D1036, D1037 (both HVC365) according to the receiving frequency.

UHF Reception

Incoming UHF signal is passed through the low-pass filter network, antenna switching diodes D1060 and D1082 (both HSC277), and Low-pass filter network to the RF amplifier Q1081 (3SK296ZQ). The amplified RF signal is passed through band-pass filtered again by varactor-tuned resonators L1049, L1050 and L1051, and D1054, D1055, and D1056 (all HVC350B), then applied to the 1st mixer Q1080 (3SK296ZQ) along with the first local signal from the PLL circuit.

The first local signal is generated between 382.75 MHz and 402.75 MHz by the UHF VCO, which consists of Q1065 (2SC5006) and varactor diodes D1030 (HVC375B), D1031 (HVC350B) and switching diode D1032 (HSC277) according to the receiving frequency.

and associated circuitry, and high-pass filter consisting of Q1007 (NJM12902V) and associated circuitry. The filtered audio signal is applied to the audio volume, then passes through the AF ampplifire Q1008 (TDA7233D) and MIC/ SP jack to the internal speaker or an external speaker.

Squelch Control

When no carrier received, noise at the output of the detector stage in Q1044 (TA31136FN) is amplified and band- pass filtered by the noise amp section of Q1044 (TA31136FN). The resulting DC voltage is applied to pin 47 of main CPU Q1031 (HD64F2266), which compares the squelch threshold level to that which set by the SQL knob.

While no carrier is received, pin 35 of Q1031 (HD64F2266) remains “low,“ squelch gate Q1005 and Q1091 (both DTC144EE) to turns off to disable any demodulated audio pass.

Transmit Signal Path

The speech signal from the microphone to AF amplified Q1019 (NJM12902V). The amplified speech signal passes through low-pass filter network Q1019 (NJM12902V) to deviation controlled by Q1030 (BU2090FS).

VHF Transmit Signal Path

The adjusted speech signal is delivered to VHF VCO Q1067 (2SC5006) which frequency modulates the trans- mitting VCO made up of D1037 (HVC365).

The modulated transmit signal passes through buffer amplifier Q1068 and Q1070 (both 2SC5006).

IF and Audio Circuits

The 47.25 MHz first IF signal is applied to the monolithic crystal filters XF1001 which strip away unwanted mixer products, and the IF signal is applied to the first IF amplifier Q1049 (2SC4915). The amplified first IF signal is then delivered to the FM IF subsystem IC Q1044 (TA31136FN), which contains the second mixer, limiter amplifier, noise amplifier, and FM detector.

The second local signal is generated by 46.8 MHz crystal X1002 and Q1041 (2SC4915), produces the 450 kHz sec- ond IF signal when mixed with first IF signal within Q1044 (TA31136FN).

The 450 kHz second IF signal is applied to the ceramic filter CF1001 which strip away unwanted mixer products to the ceramic discriminator CD1001 which removes any amplitude variations in the 450 kHz IF signal before detection of speech.

The detected audio passes through the de-emphasis network, low-pass filter consisting of Q1007 (NJM12902V)

The filtered transmit signal applied to the Pre-Drive amplifier Q1071 (2SC5006) and Drive amplifier Q1074 (2SK2596), then finally amplified by Power amplifier Q1075 (RD07MVS1) up to 5 Watts. This two stages pow- er amplifier's gain is controlled by the APC circuit.

The 5 Watts RF signal passes through low-pass filter network, antenna switch D1050 (RLS135), and another low- pass filter network, and then deliver to the ANT jack.

UHF Transmit Signal Path

The adjusted speech signal is delivered to UHF VCO Q1065 (2SC5006) which frequency modulates the trans- mitting VCO made up of D1030 (HVC375).

The modulated transmit signal passes through buffer amplifier Q1066 and Q1069 (both 2SC5006).

Circuit Description

The 5 Watts RF signal passes through high-pass filter and high-pass filter network, antenna switch D1044 (RLS135), and another low-pass filter network, and then deliver to the ANT jack.

TX APC Circuit

A portion of the Power amplifier output is rectified by D1051 (UHF: D1046 and D1047) (all RB751S), then de- livered to APC Q1054 (TA75S01F), as a DC voltage which is proportional to the output level of the power amplifier.

The APC Q1054 (TA75S01F) is compared the rectified DC voltage from the power amplifier and the reference voltage from the main CPU Q1031 (HD64F2266), to produce a control voltage, which regulates supply voltage to the Drive amplifier Q1074 (2SK2596) and Power amplifier Q1075 (RD07MVS1), so as to maintain stable output power under varying antenna loading condition.

PLL

A portion of the output from the VCO Q1065 (UHF: 2SC5006) and Q1067 (VHF: 2SC5006), passes through buffer amplifier Q1066 (UHF), Q1068 (VHF), and Q1040 (all 2SC5006) programmable divider section of the PLL IC Q1037 (MB15A01PFV1), which divided according to the frequency dividing data that is associated with the setting frequency input from the main CPU Q1031 (HD64F2266). It is then sent to the phase comparator.

The 11.7 MHz frequency of the reference oscillator circuit made up of X1002 is divided by the reference frequency divider section of Q1037 (MB15A01PFV1) into 2340 or 1872 parts to become 5 kHz or 6.25 kHz comparative reference frequencies, which are utilized by the phase comparator.

The phase comparator section of Q1037 (MB15A01PFV1) compares the phase between the frequency-divided oscillation frequency of the VCO circuit and comparative frequency and its output is a pulse corresponding to the phase difference. This pulse is integrated by the charge pump and loop filter of Q1037 (MB15A01PFV1) into a control voltage (VCV) to control the oscillation frequency of the VCOs.

Alignment

Introduction

The FT-60R is carefully aligned at the factory for the specified performance across the amateur band. Realignment should therefore not be necessary except in the event of a component failure. Only an authorized Vertex Standard representative should perform all component replacement and service, or the warranty policy may be void.

The following procedures cover the adjustments that are not normally required once the transceiver has left the factory. However, if damage occurs and some parts subsequently are replaced, realignment may be required. If a sudden problem occurs during normal operation, it is likely due to component failure; realignment should not be done until after the faulty component has been replaced.

We recommend that servicing be performed only by authorized Vertex Standard service technicians who are experienced with the circuitry and fully equipped for repair and alignment. If a fault is suspected, contact the dealer from whom the transceiver was purchased for instructions regarding repair. Authorized Vertex Standard service technicians realign all circuits and make complete performance checks to ensure compliance with factory specifications after replacing any faulty components.

Those who do undertake any of the following alignments are cautioned to proceed at their own risk. Problems caused by unauthorized attempts at realignment are not covered by the warranty policy. Also, Vertex Standard reserves the right to change circuits and alignment procedures in the interest of improved performance, without notifying owners.

Under no circumstances should any alignment be attempted unless the normal function and operation of the transceiver are clearly understood, the cause of the malfunction has been clearly pinpointed and any faulty components replaced, and realignment determined to be absolutely necessary.

Required Test Equipment

The following test equipment (and familiarity with its use) is necessary for complete realignment. Correction of problems caused by misalignment resulting from use of improper test equipment is not covered under the warranty policy. While most steps do not require all of the equipment listed, the interactions of some adjustments may require that more complex adjustments be performed afterwards.

Do not attempt to perform only a single step unless it is clearly isolated electrically from all other steps. Have all test equipment ready before beginning and, follow all of the steps in a section in the order presented.

 RF Signal Generator with calibrated output level at 500

MHz

 Deviation Meter (linear detector)  In-line Wattmeter with 5% accuracy at 500 MHz  50-Ohm 10-W RF Dummy Load  8-Ohm AF Dummy Load  Regulated DC Power Supply adjustable from 6 to 15

VDC, 2A

 Frequency Counter: 0.2-ppm accuracy at 500 MHz  AF Signal Generator  AC Voltmeter  DC Voltmeter: high impedance  UHF Sampling Coupler  SINAD Meter

Alignment Preparation & Precautions

A 50-Ohm RF load and in-line wattmeter must be connected to the main antenna jack in all procedures that call for transmission; alignment is not possible with an antenna. After completing one step, read the next step to see if the same test equipment is required. If not, remove the test equipment (except dummy load and wattmeter, if connected) before proceeding.

Correct alignment requires that the ambient temperature be the same as that of the transceiver and test equipment, and that this temperature be held constant between 68 ~ 86° F (20° ~ 30° C). When the transceiver is brought into the shop from hot or cold air, it should be allowed some time to come to room temperature before alignment. Whenever possible, alignments should be made with oscillator shields and circuit boards firmly affixed in place. Also, the test equipment must be thoroughly warmed up before beginning.

Note: Signal levels in dB referred to in the alignment pro-

cedure are based on 0dBµ = 0.5µV.

Alignment

Test Setup

Set up the test equipment as shown below for transceiver alignment, and apply 9.9 V DC power to the transceiver. Refer to the drawings for Alignment Points.

RF Signal Generator

In-Line

Wattmeter

50-ohm RF

Dummy Load

Deviation

Meter

Frequency

Counter

8-ohm AF

Dummy Load

SINAD Meter

AF Signal

Generator

AF Signal Input

AF Signal Output

Regulated

9.9 VDC P.S.

FT-60R ALIGNMENT SETUP

Entering the Alignment Mode

Alignment of the FT-60R is performed using a front panel software-based procedure. To perform alignment of the transceiver, it must first be placed in the “Alignment Mode,” in which the adjustments will be made and then stored into memory.

To enter the Alignment mode:

1. Press and hold in the MONI and LAMP switches turn-

ing the radio on. Once the radio is on, release these two switches.

2. Press the keypad in the following sequence: [(

MHz)]  [0

3. Press the [F/W] key to cause “A0 REF.xxx” to appear on the display for five seconds, this signifies that the transceiver is now in the “Alignment Mode.”

( )

SET] 

[1(

SQ TYP)]  [7(P1)]  [V/M(PRI

)]

PLL Reference Frequency

1. Tune the frequency to 435.050 MHz, then set the transmit power level to “LOW.”

2. Press the [F/W] key, then press the [BAND(BAND DN key to set the alignment parameter to “A0 REF.xxx,” if needed.

3. With in five second of appearing the “A0 REF.xxx” on the display, press the PTT switch to activate the transmitter, adjust the DIAL knob so that the counter frequency reading is 435.050 MHz (±100 Hz).

RF Front-end Tuning

1. Connect the DC voltmeter to TP1015 on the MAIN unit, then inject a 439.050 MHz signal at a level of +10 dBµ (with 1 kHz modulation @±3.5 kHz deviation) from the RF signal generator.

2. Tune the frequency to 439.050 MHz.

3. Press the [F/W] key, then press the [BAND(BAND DN key to set the alignment parameter to “A1 TUN.xxx.”

4. With in five second of appearing the “A1 TUN.xxx” on the display, adjust the DIAL knob so that the DC voltmeter reaches maximum deflection. The FT-60R’s R F Front-end has a broad bandwidth. Therefore, prior to adjustment you must adjust the DIAL knob to set the frequency to the middle of the band, in step 2, so you can set peak in the DC voltmeter’s deflection in the center of the RF passband.

5. Tune the frequency to 145.050 MHz.

6. Inject a 145.050 MHz signal at a level of +10 dBµ (with 1 kHz modulation @±3.5 kHz deviation) from the RF signal generator.

7. Press the [F/W] key to recall the alignment parameter to “A1 TUN.xxx.”

8. With in five second of appearing the “A1 TUN.xxx” on the display, adjust the DIAL knob so that the DC voltmeter reaches maximum deflection. As in the previous section, be sure to set the DIAL knob for the center of the band prior to making this adjustment.

)]

TP1015

MAIN UNIT TEST POINT

Alignment

TX Power Output

1. Tune the frequency to 440.050 MHz, then set the transmit power level to “LOW.”

2. Press the [F/W] key, then press the [BAND(BAND DN key to set the alignment parameter to “A2 PWR.xxx.”

3. With in five second of appearing the “A2 PWR.xxx” on the display, press the PTT switch to activate the transmitter, adjust the DIAL knob so that the wattmeter reading is 0.5 Watts (±0.05 Watt).

4. Increase the Transmit power level to “MID.”

5. Press the [F/W] key to recall the alignment parameter “A2 PWR.xxx.”

6. With in five second of appearing the “A2 PWR.xxx” on the display, press the PTT switch to activate the transmitter, adjust the DIAL knob so that the wattmeter reading is 2.0 Watts (±0.1 Watt).

7. Increase the Transmit power level to “HIGH.”

8. Press the [F/W] key to recall the alignment parameter “A2 PWR.xxx."

9. With in five second of appearing the “A2 PWR.xxx” on the display, press the PTT switch to activate the transmitter, adjust the DIAL knob so that the wattmeter reading is 5.0 Watts (±0.1 Watt).

10. Tune the frequency to 146.050 MHz, then set the transmit power level to “LOW.”

11. Press the [F/W] key to recal the alignment parameter “A2 PWR.xxx.”

12. With in five second of appearing the “A2 PWR.xxx” on the display, press the PTT switch to activate the transmitter, adjust the DIAL knob so that the wattmeter reading is 0.5 Watts (±0.05 Watt).

13. Increase the Transmit power level to “MID.”

14. Press the [F/W] key to recall the alignment parameter “A2 PWR.xxx.”

15. With in five second of appearing the “A2 PWR.xxx” on the display, press the PTT switch to activate the transmitter, adjust the DIAL knob so that the wattmeter reading is 2.0 Watts (±0.1 Watt).

16. Increase the Transmit power level to “HIGH.”

17. Press the [F/W] key to recall the alignment parameter “A2 PWR.xxx” again.

18. With in five second of appearing the “A2 PWR.xxx” on the display, press the PTT switch to activate the transmitter, adjust the DIAL knob so that the wattmeter reading is 5.0 Watts (±0.1 Watt).

TX Deviation

1. Tune the frequency to 440.050 MHz, then set the transmit power level to “LOW.”

)]

2. Inject a 1 kHz audio tone at a level of 80 mV (–20 dBm) from the audio generator.

3. Press the [F/W] key, then press the [BAND(BAND DN key to set the alignment parameter to “A3 DEV.xxx.”

4. With in five second of appearing the “A3 DEV.xxx” on the display, press the PTT switch to activate the transmitter, adjust the DIAL knob so that the deviation meter reading is 4.2 kHz (±0.2 kHz) (EXP version: 4.5 kHz ±

0.2 kHz).

5. Tune the frequency to 146.050 MHz, then set the transmit power level to “LOW.”

6. Press the [F/W] key to recall the alignment parameter to “A3 DEV.xxx.”

7. With in five second of appearing the “A3 DEV.xxx” on the display, press the PTT switch to activate the transmitter, adjust the DIAL knob so that the deviation meter reading is 4.2 kHz (±0.2 kHz) (EXP version: 4.5 kHz ±

0.2 kHz).

)]

DCS TX Deviation

1. Tune the frequency to 440.050 MHz, then activate the DCS, and set the transmit power level to “LOW.”

2. Press the [F/W] key, then press the [BAND(BAND DN key to set the alignment parameter to “A4 DCS.xxx.”

3. With in five second of appearing the “A4 DCS.xxx” on the display, press the PTT switch to activate the transmitter (with no microphone input), adjust the DIAL knob so that the deviation meter reading is 0.7 kHz (±0.05 kHz).

4. Tune the frequency to 146.050 MHz, then activate the DCS, and set the transmit power level to “LOW.”

5. Press the [F/W] key to recall the alignment parameter to “A4 DCS.xxx.”

6. With in five second of appearing the “A4 DCS.xxx” on the display, press the PTT switch to activate the transmitter (with no microphone input), adjust the DIAL knob so that the deviation meter reading is 0.7 kHz (±0.05 kHz).

)]

Alignment

CTCSS TX Deviation

1. Tune the frequency to 440.050 MHz, then activate the CTCSS encoder with a “100 Hz” tone, and set the transmit power level to “LOW.”

2. Press the [F/W] key, then press the [BAND(BAND DN key to set the alignment parameter to “A5 CTC.xxx.”

3. With in five second of appearing the “A5 CTC.xxx” on the display, press the PTT switch to activate the transmitter (with no microphone input), adjust the DIAL knob so that the deviation meter reading is 0.7 kHz (±0.05 kHz).

4. Tune the frequency to 146.050 MHz, then activate the CTCSS encoder with a “100 Hz” tone, and set the transmit power level to “LOW.”

5. Press the [F/W] key to recall the alignment parameter to “A5 CTC.xxx.”

6. With in five second of appearing the “A5 CTC.xxx” on the display, press the PTT switch to activate the transmitter (with no microphone input), adjust the DIAL knob so that the deviation meter reading is 0.7 kHz (±0.05 kHz).

S-meter Sensitivity

1. Tune the frequency to 440.050 MHz.

2. Inject a 440.050 MHz signal at a level of –5 dBµV (with 1 kHz modulation @±3.5 kHz deviation) from the RF signal generator.

3. Press the [F/W] key, then press the [BAND(BAND DN key to set the alignment parameter to “A6 SM U/D.”

4. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

5. Increase the RF signal generator output level to +23 dBµV.

6. Press the [F/W] key to recall the alignment parameter to “A6 SM U/D.”

7. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

8. Tune the frequency to 850.050 MHz.

9. Inject a 850.050 MHz signal at a level of +5 dBµV (with 1 kHz modulation @±3.5 kHz deviation) from the RF signal generator.

10. Press the [F/W] key to recall the alignment parameter to “A6 SM U/D.”

11. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

12.Increase the RF signal generator output level to +31 dBµV.

13. Press the [F/W] key to recall the alignment parameter to “A6 SM U/D.”

14. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

15. Tune the frequency to 146.050 MHz.

16. Inject a 146.050 MHz signal at a level of –5 dBµV (with 1 kHz modulation @±3.5 kHz deviation) from the RF signal generator.

)]

17. Press the [F/W] key to recall the alignment parameter to “A6 SM U/D.”

18. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

19.Increase the RF signal generator output level to +23 dBµV.

20. Press the [F/W] key to recall the alignment parameter to “A6 SM U/D.”

21. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

22. Tune the frequency to 230.050 MHz.

23. Inject a 230.050 MHz signal at a level of –5 dBµV (with 1 kHz modulation @±3.5 kHz deviation) from the RF signal generator.

24. Press the [F/W] key to recall the alignment parameter to “A6 SM U/D.”

25. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

26.Increase the RF signal generator output level to +23 dBµV.

27. Press the [F/W] key to recall the alignment parameter to “A6 SM U/D.”

28. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

29. Tune the frequency to 350.050 MHz.

30. Inject a 350.050 MHz signal at a level of –5 dBµV (with 1 kHz modulation @±3.5 kHz deviation) from the RF signal generator.

31. Press the [F/W] key to recall the alignment parameter to “A6 SM U/D.”

32. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

33.Increase the RF signal generator output level to +23 dBµV.

34. Press the [F/W] key to recall the alignment parameter to “A6 SM U/D.”

35. With in five second of appearing the “A6 SM U/D” on the display, press the [(MHz)] key.

DC Voltmeter

1. Set the power supply voltage to 9.9 V.

2. Press the [F/W] key, then press the [BAND(BAND DN key to set the alignment parameter to “A7 BAT RV.”

3. With in five second of appearing the “A7 BAT RV” on the display, press the [HM/RV] key.

To close the alignment mote, just turn the power off by rotating the VOL knob fully counter clockwise. The next time the transceiver is turned on, normal operation may resume.

)]

MAIN Unit (Lot. 1 ~ 5)

Circuit Diagram

RX: 5.01 V

RX: 1.79 V

RX: 1.12 V

RX: 0.64 V

RX: 1.20 V



146 M: +10.4 dBµ 440 M: +7.0 dBµ 230 M: +11.9 dBµ 350 M: +12.9 dBµ 850 M: –0.5 dBµ

RX: 2.88 V

RX: 1.85 V

RX: 4.81 V

RX: 2.06 V

RX: 2.31 V

RX: 0.66 V RX: 3.96 V

RX: 3.65 V

RX: 2.73 V

RX: 0.71 VRX: 1.69 V

RX: 0.94 V

RX AM: 0.79 V RX AM: 0.67 V

RX: 1.84 V

RX AM: 0.19 V

RX AM: 3.95 V

RX: 3.98 V



RX AM: 1.58 V RX AM: 3.95 V

RX AM: 0.54 V

RX AM: 0.62 V

RX AM: 0.07 V

146 M: +6.7 dBµ 440 M: +3.1 dBµ 230 M: +7.8 dBµ 350 M: +8.6 dBµ 850 M: –3.0 dBµ

RX: 4.07 V

RX: 0.85 V

RX: 0.15 V

RX: 2.91 V

RX: 2.66 V

RX AM: 4.94 V

VHF VCO: 4.17 V

RX: 4.30 V

UHF VCO: 4.13 V

SHIFT ON: 4.19 V

146M TX: 4.81 V

SHIFT ON: 4.24 V

RX: 2.98 V

230M: 4.75 V

440M RX: 1.24 V 440M TX: 0.93 V 850M RX: 0.88 V

TX: 1.66 V

146M RX: 1.26 V 146M TX: 1.00 V 230M RX: 0.86 V

440M: 4.88 V

146M: 4.88 V

350M: 4.92 V

850M: 4.93 V

RX: 4.18 V

146M TX: 1.19 V 440M TX: 1.72 V

440M: 2.27 V 350M: 1.77 V 850M: 1.72 V

440M TX: 4.86 V

RX: 0.40 V

TX: 0.74 V

TX: 2.21 V

RX: 3.90 V

RX: 4.04 V

RX: 0.18 V

146M: 1.53 V 230M: 0.97 V

146M: +12.4 dBm 440M: +7.8 dBm

TX: 3.02 V

RX: 2.34 V

RX: 1.57 V

RX: 1.00 V

RX: 3.04 V

RX: 1.37 V

RX: 0.62 V

RX: 2.21 V

RX: 4.14 V

146M TX: 8.55 V 440M TX: 8.60 V

RX: 0.70 V

RX: 1.58 V

146M TX: 2.36 V 440M TX: 2.78 V

RX: 2.51 V

RX: 3.94 V

RX: 4.65 V

RX: 0.69 V

–2.8 dBµ

440M: 0.19 V 350M: 0.17 V

RX: 4.13 V

RX: 0.71 V

RX: 4.55 V

RX: 0.69 V

RX: 4.75 V

+1.5 dBµ

RX: 4.80 V

+7.8 dBµ

RX: 3.69 V

RX: 3.29 V

RX: 0.37 V

TX: 1.64 V

TX: 0.80 V

–8.4 dBµ

RX: 4.62 V RX: 0.77 V

440M: 0.74 V 350M: 0.69 V

440M: 2.62 V 350M: 2.67 V

RX: 2.61 V

RX: 0.84 V

RX: 0.24 V

RX: 2.54 V

RX: 0.84 V

TX: 1.64 V

440M: 4.14 V +3.3 dBµ 350M: 3.89 V +0.5 dBµ

TX: 0.81 V

146M: 2.06 V 230M: 2.03 V

RX: 2.76 V

RX: 2.71 V

TX: 2.41 V

TX: 4.80 V

TX: 2.38 V

TX: 1.67 V

TX: 0.84 V

RX: 12.8 V

RX: 1.14 V

RX: 0.45 V

RX: 2.98 V

RX: 2.05 V

RX: 5.01 V

RX: 12.9 V

RX: 8.64 V

RX: 4.07 V

RX: 2.41 V

RX: 12.7 V

RX: 13.5 V

RX: 3.01 V

RX: 12.9 V

RX: 3.56 V

RX: 0 V

RX: 9.08 V

RX: 5.01 V

RX: 2.97 V

RX: 2.05 V

RX: 2.08 V

RX: 1.90 V

RX: 2.05 V

SQL OFF: 0 V SQL ON: 2.96 V

POWER ON: 2.97 V

AF OFF: 2.95 V

RX: 2.16 V

RX: 1.88 V

MAX: 1.20 V

PTT ON: 2.91 V

LAMP KEY: 1.87 V MONI KEY: 1.49 V

RX: 2.95 V

LAMP ON: 2.97 V

RX: 1.43 V

RX: 2.96 V

RX: 5.23 V

RX: 13.6 V

RX: 13.8 V

RX: 4.85 V TX: 0 V

CHG: 13.2 V

CHG: 1.50 V

RX: 1.85 V

CHG: 1.90 V

RX: 1.88 V

RX: 1.92 V

RX: 1.90 V

RX: 5.01 V

RX: 1.86 V

RX: 2.05 V

RX: 5.01 V

RX: 2.09 V

RX: 1.91 V

RX: 2.09 V

RX: 1.85 V

RX: 1.91 V

EAI ON: 0 V EAI NOR: 4.97 V

RX: 2.98 V

RX WIDE: 2.02 V RX NARROW: 0 V

LOW CTCSS TONE ON: 2.05 V LOW CTCSS TONE OFF: 0 V

RX: 2.97 V

RX: 2.98 V

RX: 3.21 V

RX: 1.94 V

RX: 11.5 V

RX: 2.45 V

RX: 4.43 V

RX: 4.41 V

MAIN Unit (Lot. 1 ~ 5)

Note

MAIN Unit (Lot. 1 ~ 5)

Parts Layout (Side A)

BA DC FE G

HD64F2266

(Q1031)

BU2090FS

(Q1055)

RD07MVS1

(Q1075)

2SA1774 (FR)

(Q1051, 1056, 1057,

1059, 1060)

2SB1132 (BA) (Q1011, 1072)

2SC4617 (BR) (Q1015, 1017,

1073, 1088)

2SC5006 (24)

(Q1077, 1078,

1082, 1084)

2SC5277 (D2)

(Q1079)

3SK296ZQ (ZQ)

(Q1081, 1083)

DTA144EE (16)

(Q1032, 1052, 1061)

DTC144EE (26)

(Q1014, 1064,

1076, 1089, 1090)

NJU7007F2

(Q1087)

S-80848CNNB

(Q1016)

UMA8N (A8)

(Q1058, 1062, 1063)

DA221 (K)

(D1001)

HN2D01FU (A1)

(D1013, 1029, 1069)

DAN222 (N)

(D1028)

DAP222 (P)

(D1027)

+ 35 hidden pages